CODE : 00Z

CONTENTS

Parts marked with "!" are important for maintaining the safety of the set. Be sure to replace these parts with specifiedones for maintaining the safety and performance of the set.

This document has been published to be usedfor after sales service only.The contents are subject to change without notice.

PROGRAMMING MANUAL

LEAD-FREE SOLDER MODEL

XEA21SUPME

ELECTRONICCASH REGISTER

MODEL XE-A21S

■ LEAD-FREE SOLDER

CHAPTER 1. MASTER RESET AND PROGRAM RESET . . . . . . 1 - 1

CHAPTER 2. PROGRAM MODE . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1

CHAPTER 3. OP X/Z, X1/Z1, X2/Z2 MODE. . . . . . . . . . . . . . . . . . 3 - 1

XE-A21S LEAD-FREE SOLDER

■ LEAD-FREE SOLDERThe PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder. Thealphabet following the “LF” mark shows the kind of lead-free solder.

Example:

(1) NOTE FOR THE USE OF LEAD-FREE SOLDER THREAD

When repairing a lead-free solder PWB, use lead-free solder thread. Never use conventional lead solder thread, which may cause a breakdown or an accident.

Since the melting point of lead-free solder thread is about 40°C higher than that of conventional lead solder thread, the use of the exclusive-use soldering iron is rec-ommendable.

(2) NOTE FOR SOLDERING WORK

Since the melting point of lead-free solder is about 220°C, which is about 40°C higher than that of conventional lead solder, and its soldering capacity is inferior toconventional one, it is apt to keep the soldering iron in contact with the PWB for longer time. This may cause land separation or may exceed the heat-resistive tem-perature of components. Use enough care to separate the soldering iron from the PWB when completion of soldering is confirmed.

Since lead-free solder includes a greater quantity of tin, the iron tip may corrode easily. Turn ON/OFF the soldering iron power frequently.

If different-kind solder remains on the soldering iron tip, it is melted together with lead-free solder. To avoid this, clean the soldering iron tip after com-pletion of soldering work. If the soldering iron tip is discolored black during soldering work, cleanand file the tip with steel wool or a fine filer.

5mm

Lead-Free

Solder composition code (Refer to the table at the right.)

Solder composition

Sn-Ag-Cu

Sn-Ag-BiSn-Ag-Bi-Cu

Sn-Zn-Bi

Sn-In-Ag-Bi

Sn-Cu-Ni

Sn-Ag-Sb

Bi-Sn-Ag-PBi-Sn-Ag

a

b

z

i

n

s

p

Solder composition code

a

XE-A21S MASTER RESET and program reset

1 – 1

CHAPTER 1. MASTER RESET AND PROGRAM RESET

1. MASTER RESETTING

Master resetting clears the entire memory and resumes initial values.

Master resetting can be accomplished by using the following procedure:

Procedure :

1) Unplug the AC cord from the wall outlet, or set the mode switch to OFF position.

2) Let the ECR be without the memory backup battery.

3) Wait over 1 minute for discharging.

4) Set the mode switch to any position except OFF.

5) Plugin the AC cord to the wall outlet, or turn the mode switch from OFF position to another position.

The master reset can also be accomplished in the following case.

In case power failure occurs when the machine has no battery attached to it, the master reset operation is automatically performed after the powerhas been restored.

(This is because if power failure occurs with no battery attached to the machine, all the memories are lost and the machine does not work properlyafter power recovery; this requires the master reset operation.)

2. PROGRAM RESETTING (INITIALIZATION)

This resetting resumes the initial program without clearing memory.

This resetting can be operated at below sequence in PGM mode.

Procedure:

1) Unplug the AC cord from the wall outlet.

2) Wait over 1 minute for discharging.

3) Set the mode switch to the PGM position.

4) While holding down the FEED key, plugin the AC cord to the wall outlet.

Note: In case power failure occurs when the machine has no battery attached to it, the master reset operation is automatically performed after thepower has been restored.

CHAPTER 2. PROGRAM MODE

1. READING STORED PROGRAMS

The machine allows you to read every program stored in the PGM mode.

■ Key sequence for reading stored program

(*1)PLU code range can be specified by entering the start and end numbers according to the following procedure.When specifying a single time interval, PLU code, the start number has only to be entered.

■ SAMPLE PRINTOUTS

1. Programming report 1

Report name Key sequence

Programming report 1

Programming report 2 2 3

[Auto] key programming report 1 3

Printer density programming report 3 3

PLU programming report (*1)

CA/AT

CA/AT

CA/AT

CA/AT

Start PLU code @/FOR End PLU code PLU

: VARIOUS PROGRAM Refer to the programming section about the data of each JOB.

HEADER

*PGM*MODE TITLE

F01 ( - ) xx 007

-1000.00F02 % 1xxxx 000L100.00% -10.00%F04 NET1F05F06F07F08F09

F25F26F27F28

TAX1 ST

::

::

F40F41F42F43

::

:F67 COPYF68 EJF69 EJ END

SHARP

SHARPPRESENTS THE

BEST ECR

ISTHE BEST

#5 000000000000000000000000

00000000

#6#7#10 0000#11 0#15#19 00#35 007#50 007T 1 10.0000%

T2 4.0000%

05/02/2006 12:34PM

123456#1234

D99 T1234 071

T1234

DPT.99 0.00

GRS TAX1RFD TAX1TAX1TX1 EXPT

GRS MTAXRFD MTAXM-TAX 7GST EXPT

***RAxxx 9***POxxx 9TRANS CT NET3

DATE/TIME/CLERK NO

MACHINE NO. /CC-NO. / CLERK NAME

D01 T1234 073DEPT CODE/TAXABLE/ PROGRAM (*1)

DPT.01xxxxxx -1234.56

D02 T1234 073DPT.02 -1234.56

TEXT/PRICE WITH SIGN

(MAX department is decided by PGM selection.)

FUNCTION NO. /TEXT /HALO

FUNCTION NO. /TEXT /HALO

FUNCTION NO. /TEXT/PROGRAM (*2)

AMOUNT WITH SIGN

FUNCTION NO. /TEXT /PROGRAM (*2) HALO WITHOUT SIGN/ RATE WITH SIGN

FUNCTION NO./TEXT

F 44 CASH FUNCTION NO. /TEXT 008

F 45 CHECKxxx008

F 46 CHRAGExx008

F 47 CHARGE-F 48 CONV 1 00

F 49 CONV 2F 50 ****CID

AAAA 9999.9999

(JOB# 5) FUNCTION SELECT(JOB# 6) PRINT FUNCTION(JOB# 7) RECEIPT PRINT FORMAT(JOB#10) POWER SAVING PROGRAMMING(JOB#11) LOGO FORMAT(JOB#15) FUNCTION SELECT2 (JOB#19) DOUGHNUT TAX EXEMPT (JOB#35) ONLINE Timeout time (JOB#50) Thermal printer densityTAX1 RATE

/ 1.001 0.112 0.233 0.574 0.785 1.11

/PROGRAM (*3)

FUNCTION NO. /TEXT/PROGRAM (*4) CURRENCY SYMBOL/RATE

CYCLE TAX /BREAK POINT AMOUNT

0.10

LOGO TEXT

FUNCTION NO. /TEXT

(It is according with LOGOFORMAT.)

TAX2 RATE LOWER TAX LIMIT

FUNCTION NO. /TEXT /PROGRAM (*3)

FUNCTION NO. /TEXT /PROGRAM (*3)

T3 5.0000%0.20

TAX3

T4 ------ TAX4 ("------": INHIBIT)C#01 CLERK.01C#02 CLERK.02

C#25 CLERK.25

Clerk No. /Clerk name

: :

BETTY___

01

XE-A21S PROGRAM MODE

2 – 1

(*1) DEPT PROGRAM : ABC

(*2) (-)/[%] PROGRAM : ABC

(*3) MEDIA PROGRAM : ABC

(*4) CONVERSION PROGRAM : AB

2. Programming report 2

3. [Auto] key programming report

4. Printer density report

A: REGISTRATION TYPE A

NORMAL 0

SICS 1

B: LIMITATION DIGITS (*2) = 0 to 7

C: AMOUNT ENTRY TYPE C

Inhibited 0

Open 1

Preset 2

Open and Preset 3

A: ENTRY FOR ITEM A

ENABLE 0

DISABLE 1

B: ENTRY FOR SBTL B

ENABLE 0

DISABLE 1

C: LIMITATION DIGITS (for (-) key) = 0 to 7 (0 FIXED for [%n])

A: Footer print on Receipt A

No 0

Yes 1

B: Entry of amount tendered B

Non compulsory (Cash, check), Inhibit (Credit)

0

Compulsory 1

C: LIMITATION DIGITS (0=INHIBIT) = 0 to 8

A: OPEN RATE ENTRY A

ENABLE 0

DISABLE 1

B: PRESET RATE ENTRY B

ENABLE 0

DISABLE 1

: OTHERS PROGRAM Refer to the programming section about the data of each JOB.

GT2

HEADER

*PGM*MODE TITLE

05/02/2006 12:34PM

123456#1234

DATE/TIME/CLERK NO

MACHINE NO./CC-NO./ CLERK NAME

#61 00000000 (JOB#61) OTHERS1 #62 00000000 (JOB#62) OTHERS2#63 00000000 (JOB#63) OTHERS3 #64 00000000 (JOB#64) OTHERS4 #65 00000000 (JOB#65) OTHERS5 #66 00000000 (JOB#66) OTHERS6 #67 00000000 (JOB#67) OTHERS7 #68 00000000 (JOB#68) OTHERS8 #69 00000000 (JOB#69) OTHERS9 #70 00000000 (JOB#70) OTHERS10 #71 GT2 #72

#76 Z1 0000 GENERAL Z1 RESET COUNTER #77 Z2 0000 GENERAL Z2 RESET COUNTER#85 ___$ DOMESTIC CURRENCY SYMBOL#86 00 TRAINING CLERK #87 TRAINING TRAINING MODE TEXT#88 0 LANGUAGE MODE

(For the fixed messages) #90 0

EJ/PLU MEMORY TYPE(0: TYPE, 1: TYPE2)

#95 99

MAX NUBMER OF DEPT

$00000000000.00

GT3GT3 $00000000000.00

01

BETTY___

HEADER

*PGM* MODE TITLE

KEY TEXT

05/02/2006 12:34PM

123456#1234

DATE/TIME/CLERK NO

MACHINE NO. /CC-NO. / CLERK NAME

#01 1000CASH

DELETE (NO KEY)------

01

BETTY___

HEADER

*PGM* MODE TITLE

05/02/2006 12:34PM

123456#1234

DATE/TIME/CLERK NO

MACHINE NO. /CC-NO. / CLERK NAME

#01 5010 : 0123456789AB20 : 0123456789AB30 : 0123456789AB40 : 0123456789AB50 : 0123456789AB60 : 0123456789AB70 : 0123456789AB80 : 0123456789AB90 : 0123456789AB

Printing Sample (Light & Shade value between 10 to 90.)

Thermal printer density

01

BETTY___

XE-A21S PROGRAM MODE

2 – 2

5. PLU data report

(*1) PROGRAM : Y

2. USER PROGRAMMING

1) PRICE PROGRAMMING FOR [DEPT.] & (-) KEYS

If a price is set for a department which amount entry type is “INHIBIT” or“OPEN”, its amount entry type is set as below automatically.

MRS = 0

2) DEPT FUNCTION PROGRAMMING

Y: PROGRAM Y

SUBDEPT 0

PLU 1

YY: Department Code (01 to 99)

XXXXXX: Unit price (Max. 6digits)

“PRESET” 1 “INHIBIT”

“OPEN & PRESET” 1 “OPEN”

HEADER

*PGM*MODE TITLE

05/02/2006 12:34PM

123456#1234

DATE/TIME/CLERK NO

MACHINE NO. /CC-NO. /CLERK NAME

P001PLU001xxxxxx

0001-12001

P001 ----

-1234.56

TEXT/PRICE WITH SIGN

START CODE/ END CODE (RANGE DATA)

::

NOTE : The deleted PLU is not printed.

PLU CODE/Associated DEPT code/Type (*1)

01

BETTY___

When PLU is deleted at the programming JOB.

XXXXXX

YY XXXXXX

0

0

CA/ATDPTn

DPTnDEPT SHIFT

DEPT# SBTL

(-)

YY: Department code (01 to 99)

A: Taxable 4 A

No 0 ★

Yes 1

B: Taxable 3 B

No 0 ★

Yes 1

C: Taxable 2 C

No 0 ★

Yes 1

D: Taxable 1 D

No 0

Yes 1 ★

E: REGISTRATION TYPE A

NORMAL 0 ★

SICS 1

F: SIGN B

+ 0 ★

- 1

G: LIMITATION DIGITS = 0 to 7

0 : OPEN PRICE REGISTRATION INHIBIT.

H: AMOUNT ENTRY TYPE D

Inhibited 0

Open 1 ★

Preset 2

Open & Preset 3

MRS = 00010071(TAXABLE 1, NORMAL, SIGN (+), HALO = 7, OPEN)

ABCDEFGH

ABCDEFGHYY

0

0

DPTn@/FOR

@/FORDEPT#

CA/AT

DPTnDEPT SHIFT

XE-A21S PROGRAM MODE

2 – 3

3) (-) & [%] KEY FUNCTION PROGRAMMING

4) RATE PROGRAMMING FOR [%] ANDCONVERSION KEY.

The DECIMAL POINT must be entered for setting the decimal digits.

5) PROGRAMMING FOR CONVERSION

MRS = 00

6) PROGRAMMING FOR FUNCTION KEYS

MRS = 7 (Manual TAX), 9 (RA, PO)

7) PROGRAMMING FOR MEDIA KEYS

([#/ST] key is used for programming of CASH.)

MRS = 008

A: Taxable 4 A

No 0 ★

Yes 1

B: Taxable 3 B

No 0 ★

Yes 1

C: Taxable 2 C

No 0 ★

Yes 1

D: Taxable 1 D

No 0 ★

Yes 1

E: SIGN E

+ 0

- 1 ★

F: ENTRY FOR ITEM F

ENABLE 0 ★

DISABLE 1

G: ENTRY FOR SBTL G

ENABLE 0 ★

DISABLE 1

H: LIMITATION DIGITS (for (-) key) = 0 to 7

0 : OPEN PRICE REGISTRATION INHIBIT (for (-) KEY)

0 : FIXED for [%]

MRS = 00001007(NON-TAXABLE, MINUS SIGN, ITEM&SBTL, HALO = 7)

(RATE): XXX.XX: Rate for % (0.00 to 100.00)

XXXX.XXXX: Rate for CONVERSION (0.0000 to 9999.9999)

MRS = 0.00 (%n)

0.0000 (CONVERSION)

(-)

%n

0

ABCDEFGH CA/AT@/FOR

0

(RATE) CA/AT%n

CONV

A: OPEN RATE ENTRY A

ENABLE 0 ★

DISABLE 1

B: PRESET RATE ENTRY B

ENABLE 0 ★

DISABLE 1

A: LIMITATION DIGITS (0 = INHIBIT)

= 0 to 7 (for Manual TAX)

= 0 to 9 (for RA, PO)

A: Footer print on Receipt A

No 0 ★

Yes 1

(0 FIXED for RA/PO)

B: Entry of amount tendered B

Non compulsory (Cash, Check), Inhibit (Credit) 0 ★

Compulsory 1

(0 FIXED for RA/PO)

C: LIMITATION DIGITS (0=INHIBIT) = 0 to 8

CONV

0

AB CA/AT@/FOR

0

A CA/ATPO@/FOR

RA

TAX

(for Manual-TAX)

ABC @/FOR CH

CHK

#/ST

(for CASH)

0

CA/AT

XE-A21S PROGRAM MODE

2 – 4

8) DATA PROGRAMMING FOR PLUThere are programmed by below key sequence.The PLU code is increment automatically when one programming dataof a PLU is set.And it is operated continuously until depressing the [CA/AT] key.The JOB is automatically finalized when a maximum PLU code is programmed.

(Basic programming sequence)

Basic operation consists of below 2 kinds.

9) PROGRAMMING OF DEPARTMENTS TO BEASSOCIATED WITH PRICE PRESET

DELETE means to be set as a inhibited PLU in memory.When it is assigned some DEPT for the inhibited (deleted) PLU,the PLU is set the MRS value except its price.

10) PROGRAMMING OF PLU/SUBDEPT

11) PROGRAMMING OF DEPARTMENT TEXT

Characters can be entered by using the character layout on keyboard orusing numeric keys on keyboard.THE KEY ENTRY SEQUENCE FOR ENTERING ONE CHARACTER BY NUMERIC KEYS IS AS FOLLOWS:

MRS = DEPT. xx (xx: DEPT Code)

12) PROGRAMMING OF PLU TEXT

Characters can be entered by using the character layout on keyboard orusing numeric keys on keyboard.THE KEY ENTRY SEQUENCE FOR ENTERING ONE CHARACTERBY NUMERIC KEYS IS AS FOLLOWS:

MRS = PLU.xxxx (xxxx: PLU code)

13) PROGRAMMING OF FUNCTION TEXT

Characters can be entered by using the character layout on keyboard orusing numeric keys on keyboard.THE KEY ENTRY SEQUENCE FOR ENTERING ONE CHARACTERBY NUMERIC KEYS IS AS FOLLOWS:

MRS = Refer to the following table

XXXX: PLU CODE (1 to 1200)

ZZ: DEPT CODE (1 to 99)

YYYYYY: UNIT PRICE (6 digits)

MRS = DEPT1, Price: 0 (Create: PLU001 to PLU1200)

XXXX: PLU CODE (1 to 1200)

Y: 0 = SUBDEPT, 1 = PLU

MRS = 1 (PLU type)

(DATA)

(Code increment)

(Code entry)

PLU DPTn CA/ATXXXXPLU CODE

SBTL(DATA)DEPT#DEPT CODE

DEPT SHIFT DPTn

(DATA)

(Code increment)

(Code entry)

PLU SBTL CA/ATXXXX

PLU CODE

YYYYYY

(Code increment)

(Code entry)

PLU DPTn

DPTn

CA/ATXXXXPLU CODE

SBTLYYYYYYDEPT#DEPT CODE

0

ZZ

0

PLU DELETE (INHIBIT)

DEPT SHIFT

Y

(Code entry)

PLU SBTL CA/ATXXXX

PLU CODE

0

XX: Department Code (1 to 99)

(CHATACTERS): CHARCTER (Max. 12 Characters)

YYY 3 [00] KEY

YYY: CHARACTER CODE (3 DIGITS)

(or [000] KEY ACCORDING TO PGM PRESET)

XXXX: PLU CODE (1 to 1200)

(CHARACTERS): CHARACTER (Max. 12 Characters)

YYY3 [00] KEY

YYY: CHARACTER CODE (3 DIGITS)

(or [000] KEY ACCORDING TO PGM PRESET)

XX: FUNCTION CODE (Refer to the FUNCTION LIST)

(CHARACTERS): CHARACTER (Max. 8 Characters)

YYY 3 [00] KEY

YYY: CHARACTER CODE (3 DIGITS)

(or [000] KEY ACCORDING TO PGM PRESET)

DPTn (CHARACTERS)

XX

SBTL SBTL 1 CA/TA

DEPT#DEPT CODE

NO CHANGE

DPTnDEPT SHIFT

PLU (CHARACTERS)

NO CHANGE

(Code increment)

(Code entry)

XXXXSBTL SBTL2 CA/ATPLU CODE

(CHARACTERS)

NO CHANGE

XXSBTL @/FOR SBTL3 CA/AT

XE-A21S PROGRAM MODE

2 – 5

■ FUNCTION LIST

14) PROGRAMMING OF LOGO TEXT

Characters can be entered by using the character layout on keyboard orusing numeric keys on keyboard.THE KEY ENTRY SEQUENCE FOR ENTERING ONE CHARACTERBY NUMERIC KEYS IS AS FOLLOWS:

(Sample)

F-NO. FUNCTIONDEFAULT12345678

1 (-) (-)

2 %1 %1

3 %2 %2

4 NET1 NET1

5 TAXABLE1 ST TAX1 ST

6 GROSS TAX1 GRS TAX1

7 REFUND TAX1 RFD TAX1

8 NET TAX1 TAX1

9 EXEMPT TAX1 TX1 EXPT

10 TAXABLE2 ST TAX2 ST

11 GROSS TAX2 GRS TAX2

12 REFUND TAX2 RFD TAX2

13 NET TAX2 TAX2

14 EXEMPT TAX2 TX2 EXPT

15 TAXABLE3 ST TAX3 ST

16 GROSS TAX3 GRS TAX3

17 REFUND TAX3 RFD TAX3

18 NET TAX3 TAX3

19 EXEMPT TAX3 TX3 EXPT

20 TAXABLE4 ST TAX4 ST

21 GROSS TAX4 GRS TAX4

22 REFUND TAX4 RFD TAX4

23 NET TAX4 TAX4

24 EXEMPT TAX4 TX4 EXPT

25 GROSS M-TAX GRS MTAX

26 REFUND M-TAX RFD MTAX

27 NET M-TAX M-TAX

28 NON GST SUBTOTAL GST EXPT

29 PST TOTAL PST TTL

30 GST TOTAL GST TTL

31 TOTAL TAX TTL TAX

32 NET without TAX NET

33 NET2 NET2

34 REFUND REFUND

35 VOID VOID

36 VOID MODE VO I D

37 MANAGER VOID MGR VD

38 SBTL VOID SBTL VD

39 NO SALE NO S ALE

40 RA ***RA

41 PO ***PO

42 CUSTOMER TRANS CT

43 NET3 (SALES) NET3

44 CASH CASH

45 CHECK CHECK

46 GROSS CHARGE1 CHARGE

47 REFUND CHARGE1 CHARGE-

48 CONVERSION (PRESET RATE) CONV 1

49 CONVERSION (OPEN RATE) CONV 2

50 CASH IN DRAWER ****C ID

51 CASH+CHECK IN DRAWER CA+CH ID

52 CHECK CHANGE CHK /CG

53 VAT EXEMPT (For DOUGHNUT TAX Type1) VAT EXPT

54 (+) DEPT TOTAL *DEPT TL

55 (-) DEPT TOTAL DEPT ( - )

56 SUBTOTAL SUBTOTAL

57 MDS SBTL MDSE ST

58 TOTAL ***TOTAL

59 CHANGE CHANGE

60 ITEMS ITEMS

61 DEPT. REPO. TITLE DEPT

62 PLU REPO. TITLE PLU

63 TRANS. REPO. TITLE TRANS.

64 CLERK REPO. TITLE CLERK

65 HOURLY REPO. TITLE HOURLY

66 NON ADD CODE TEXT #

67 COPY RECEIPT TITLE COPY

68 EJ REPORT TITLE EJ

69 EJ REPORT END TITLE EJ END

X: LINE NO. (1 to 6)

(CHARACTERS): CHARACTER (Max. 24 Characters)

YYY3 [00] KEY

YYY : CHARACTER CODE (3 DIGITS)

(or [000] KEY ACCORDING TO PGM PRESET)

F-NO. FUNCTIONDEFAULT12345678

(CHARACTERS)

NO CHANGE

LINE NO.XSBTL @/FOR SBTL4 CA/AT

PRESENTS THE

BEST ECR

I STHE BEST

SHARP

SHARPMRS =

XE-A21S PROGRAM MODE

2 – 6

15) PROGRAMMING OF CLERK NAME

Characters can be entered by using the character layout on keyboard orusing numeric keys on keyboard.THE KEY ENTRY SEQUENCE FOR ENTERING ONE CHARACTERBY NUMERIC KEYS IS AS FOLLOWS:

MRS = CLERKxx (xx: clerk no.)

16) FOREIGN CURRENCY SYMBOL PROGRAMMING

Characters can be entered by using the character layout on keyboard orusing numeric keys on keyboard.THE KEY ENTRY SEQUENCE FOR ENTERING ONE CHARACTERBY NUMERIC KEYS IS AS FOLLOWS:

MRS = ____ ( _ : space code)

Note: This symbol is printed as the amount of CURRENCY CONVER-SION for PRESET RATE only.The amount symbol of CURRENCY CONVERSION for OPEN RATE is not printed.

17) TAX TABLE PROGRAMMING

72 BREAKPOINTS CAN BE PROGRAMMED FOR EACH TAXTABLE.(Case of interval between break point is 1 dollar or more and less than100 dollar, 36 breakpoints is programmed for each table.)

* DEPRESSION OF THE [SBTL] KEY AT THE FOLLOWING POINTS MEANS A TAX TABLE DELETE OPERATION.

MRS = NO TAX

18) TAX RATE PROGRAMMING

% TAX RATE &SIGN RATE xxx.xxxx = 0.0000 to 100.0000 %

LOWER TAX LIMITATION 0.00 to 999.99(This is invalid in VAT system.)

MRS = DELETE

19) RATE HALO PROGRAMMING FOR [%] KEY

The DECIMAL POINT must be entered for setting the decimal digits.

MRS = 100.00 (%)

XX: CLERK NO. (1 to 25)

(CHARACTERS): CHARACTER (Max. 8 Characters)

YYY3 [00] KEY

YYY : CHARACTER CODE (3 DIGITS)

(or [000] KEY ACCORDING TO PGM PRESET)

(CHARACTERS): CHARACTER (Max. 4 Characters)

YYY3 [00] KEY

YYY : CHARACTER CODE (3 DIGITS)

(or [000] KEY ACCORDING TO PGM PRESET)

(CHARACTERS)

NO CHANGE

XXSBTL @/FOR SBTL5 CA/AT

(CHARACTERS)

NO CHANGE

SBTL SBTL6 CA/AT

SBTL @/FOR

CA/AT

SBTL

xx.xxxx

xxxx

AB

*

TAX RATE

CYCLExxx

INITIAL TAX

(Table Delete programming)

(Table Delete programming)

DECLARATION OF TAX

8

xxxxx

LOWER TAX LIMIT

@/FOR @/FOR

@/FOR @/FOR

xxxxx

BREAK POINT

@/FOR @/FOR

A: INTERVAL BETWEEN BREAKPOINTS A

BELOW 1 DOLLAR 0

1 DOLLAR OR MORE AND LESS THAN 100 DOLLAR 1

B: TAX TABLE No. B

TABLE1 1

TABLE2 2

TABLE3 3

TABLE4 4

TAX RATE : 0.0001 to 99.9999

CYCLE : 0 to 9999

INITIAL TAX : 0 to 999

LOWER TAX LIMIT : 0 to 99999

BREAK POINT : 0 to 99999

A : TAX 1 PROGRAMMING 1

TAX 2 PROGRAMMING 2

TAX 3 PROGRAMMING 3

TAX 4 PROGRAMMING 4

XXX.XX: % HALO (0.00 to 100.00)

@/FOR

SBTL CA/AT

@/FOR9

0

0

(Inhibition programming)

xxx.xxxxTAX RATE

SBTL ATAX NO.

@/FOR xxxxx LOWER TAX LIMIT

FOR ADD TAX

XXX.XX

0

SBTL @/FOR % n29 CA/AT

XE-A21S PROGRAM MODE

2 – 7

20) [AUTO] KEY PROGRAMMING

It must be pushed same [AUTO] key as the programming [AUTO] key atthe end of any key entry.

Note: [ESC] key cannot be set at [AUTO] key programming.It acts as a key of ERROR ESCAPE function in this programming.

< [Auto] key function >

This machine has [AUTO] key which can be programmed the key-sequence data.When [AUTO] key is depressed, the machine works as same as theprogrammed key-sequence is entered.

21) DATE/TIME PROGRAMMING

Note: It cannot set the non-exist date (like Feb.-30th).

22) VARIOUS PROGRAMMING(EACH FUNCTIONS PROGRAMMING)

There are programmed by depressing ST-key after a data that want toset. And it is operated continuously until depressing the TL-key.

[JOB#1] MACHINE No. (6digits) -- XXXXXX --

MRS = 000000

[JOB#2] CONSECUTIVE No. (4digits) -- XXXX --

MRS = 0000

[JOB#5] FUNCTION SELECT -- ABCDEFGH --

MRS = 00000001

[JOB#6] PRINT FORMAT -- ABCDEFGH --

MRS = 11000011

Note: Case of RECEIPT, ECR is controlled the Journal Rewind Motor as below.

Executing mode : REG, MGR, OPXZ, X1/Z1, X2/Z2

Setting mode : PGM

DATE) XXXXXXXX: YYYYMMDD (Year-month-day) orDDMMYYYY (Day-month-Year) orMMDDYYYY (Month-day-Year)

(YYYY: 2000 to 2099)

(MM: 01 to 12)

(DD: 01 to 31)

The date entry format complies with the applicable PGM-modeprogramming.

TIME) HH: Hour (00 to 23)

MM: Minute (00 to 59)

MRS = DATE: 01012000 (MM/DD/YYYY)

TIME: 0000

(Free key)

max 25

Delete

AUTO AUTO CA/AT

XXXXXXXX DATE

HHMM TIME

#/SBTL

(NK) #/SBTL

0

AB

AB : JOB No.NK : PROGRAMMING DATA. (Numeric Keys)

CA/AT#/SBTL @/FOR

A: PO in REG mode A

ENABLE 0 ★

DISABLE 1

B: RA in REG mode B

ENABLE 0 ★

DISABLE 1

C: SUBTOTAL VOID in REG mode C

ENABLE 0 ★

DISABLE 1

D: INDIRECT VOID in REG mode D

ENABLE 0 ★

DISABLE 1

E: DIRECT VOID in REG mode E

ENABLE 0 ★

DISABLE 1

F: REFUND in REG mode F

ENABLE 0 ★

DISABLE 1

G: NO SALE in REG mode G

ENABLE 0 ★

DISABLE 1

H: FRACTIONAL QUANTITY H

YES (3digits decimal place) 0

NO 1 ★

A: PRINTER FORMAT A

JOURNAL 0

RECEIPT 1 ★

REG/MGR/VOID mode : Journal Rewind Motor is not driven.

PGM/OPXZ/XZ mode : Journal Rewind Motor is driven for rewinding reports anytime.

B: CONTENTS OF RECEIPT B

TOTAL 0

DETAIL 1 ★

C: TIME PRINTING (for all receipt) C

PRINT 0 ★

NOT PRINT 1

D: DATE PRINTING (for all receipt) D

PRINT 0 ★

NOT PRINT 1

XE-A21S PROGRAM MODE

2 – 8

[JOB#7] RECEIPT PRINT FORMAT -- ABCDEFGH --

MRS = 00000000

[JOB#10] POWER SAVING -- YXXX --

MRS = 0030

[JOB#11] LOGO PRINTING -- A --

MRS = 1

[JOB#15] FUNCTION SELECT2 -- ABCDEFGH--

MRS = 000000000

[JOB#19] QUANTITY FOR DOUGHNUT EXEMPT -- XX --(for CANADIAN TAX)

MRS = 0

xx : QUANTITY FOR DOUGHNUT TAX EXEMPT = 0 to 99

[JOB#35] ONLINE COMMUNICATION TIME OUT -- XXX --

MRS = 007

XXX: Time out time (1 to 255 sec)

[JOB#50] THERMAL PRINTER DENSITY CONTROL -- XX --

MRS = 50

XX: density (00 to 99)

00 : 70 % for standard 50 : 100 % (Standard density) 99 : 130 % for standard

[JOB#61] OTHERS1 PROGRAMMING -- ABCDEFGH --

MRS = 00100002

E: CONSECUTIVE NO. PRINTING E

PRINT 0

NOT PRINT 1 ★

F: Not used (Fixed at “0”)

G: ZERO SKIP IN PLU REPORT G

NOT SKIP 0

SKIP 1 ★

H: ZERO SKIP IN GENERAL,CLERK,HOURLY H

NOT SKIP 0

SKIP 1 ★

A, B: Not used (Fixed at “00”)

C: SUBTOTAL PRINT [AT] [SBTL] KEY C

NOT PRINT 0 ★

PRINT 1

D: MDSE SBTL PRINT AT [MDSE SBTL] KEY D

NOT PRINT 0 ★

PRINT 1

E, F, G: Not used (Fixed at “000”)

H: PURCHASE NO. PRINTING H

PRINT 0 ★

NOT PRINT 1

Y: POWER SAVING function when a time is displayed Y

Yes (Enable) 0 ★

No (Disable) 1

XXX: POWER SAVING TIME to POWER OFF= 001 to 254 (minutes) or 999 (Inhibit)

A: LOGO MESSAGE CONTROL A

3-LINE HEADER INSTEAD OF GRAPHIC LOGO 0

GRAPHIC LOGO ONLY 1 ★

GRAPHIC LOGO AND 3-LINE FOOTER 2

6-LINE HEADER 3

GRAPHIC LOGO AND 3-LINE HEADER 4

3-LINE HEADER AND 3-LINE FOOTER 5

A, B, C, D, E, F: Not used (Fixed at “000000”)

G: TAX DELETE in REG mode G

ENABLE 0 ★

DISABLE 1

H: MANUAL TAX in REG mode H

ENABLE 0 ★

DISABLE 1

A, B: Not used (Fixed at “00”)

C: Programming of MINUS dept/PLU C

Disable 0

Enable 1 ★

D: Fractional treatment D

Round off (4-DOWN, 5-UP) 0 ★

Raising to unit 1

Disregarding 2

E: [00] key or [000] key selection for [00] key position E

[00] key 0 ★

[000] key 1

F: Time format F

12hour 0 ★

24hour 1

G: Date format G

M-D-Y 0 ★

D-M-Y 1

Y-M-D 2

H: TAB H

0 0

1 1

2 2 ★

3 3

XE-A21S PROGRAM MODE

2 – 9

[JOB#62] OTHERS2 PROGRAMMING -- ABCDEFGH --

MRS = 00000000

[JOB#63] OTHERS3 PROGRAMMING -- ABCDEFGH --

MRS = 01010001

[JOB#64] OTHERS4 PROGRAMMING -- ABCDEFGH --

MRS = 00000000

[JOB#65] OTHERS5 PROGRAMMING -- ABCDEFGH --

MRS = 00000000

A: Not used (Fixed at “0”)

B: ERROR BEEP for missoperation B

LOCK ERROR 0 ★

MISSOPERATION 1

C: Key catch sound C

Yes 0 ★

No 1

D: Buffered Keyboard D

Yes 0 ★

No 1

E: VOID mode E

Enable 0 ★

Disable 1

F: Printing of VOID MODE in Z2 report F

Yes 0 ★

No 1

G: Printing of VOID MODE in Z1 report G

Yes 0 ★

No 1

H: Addition to the hourly total in VOID MODE H

No 0 ★

Yes 1

A: Receipting at the time of NO SALE A

Yes 0 ★

No 1

B: NO SALE after non-add code entry B

Disable 0

Enable 1 ★

C: NON-ADD code entry C

Enable 0 ★

Disable 1

D: Copy Receipt D

No 0

Yes 1 ★

E: Entry that causes the merchandise SUBTOTALto be smaller than zero. E

Enable 0 ★

Disable 1

F: Subtotal entry before tendering F

Noncompulsory 0 ★

Compulsory 1

G: Subtotal entry before direct non-tender finalization G

Noncompulsory 0 ★

Compulsory 1

H: Direct non-tender finalization after tendering H

Disable 0

Enable 1 ★

A: Printing of GT1 on Z report A

Yes 0 ★

No 1

B: Printing of GT2 on Z report B

Yes 0 ★

No 1

C: Printing of GT3 on Z report C

Yes 0 ★

No 1

D: Printing of Training GT on Z report D

Yes 0 ★

No 1

E: Printing of Z counter on Z report E

Yes 0 ★

No 1

F: Printing of DATA on PLU resetting report F

Yes 0 ★

No 1

G: Reset GT1,2,3 at the general Z1 report G

No 0 ★

Yes 1

H: OP X/Z report H

Enable 0 ★

Disable 1

A, B, C, D, E, F, G, H: Not used (Fixed at “00000000”)

XE-A21S PROGRAM MODE

2 – 10

[JOB#66] OTHERS6 PROGRAMMING -- ABCDEFGH --

MRS = 10001100

[JOB#67] OTHERS7 PROGRAMMING -- ABCDEFGH -- MRS = 00000000

[JOB#68] OTHERS8 PROGRAMMING -- ABCDEFGH --

MRS = 00100011

[JOB#69] OTHERS9 PROGRAMMING -- ABCDEFGH --

MRS = 00000000

[JOB#70] OTHERS10 PROGRAMMING -- ABCDEFGH --

MRS = 00000000

A: AFTER-TRANSACTION RECEIPT A

TOTAL ONLY 0

DETAILS 1 ★

B: AMOUNT PRINTING WHEN PLU UNIT PRICE IS 0 B

No 0 ★

Yes 1

C: CONVERSION SBTL PRINTING OF NATIVE SBTL C

Yes 0 ★

No 1

D: Not used (Fixed at “0”)

E: Compression print on journal at PGM/XZ mode E

No (Normal size) 0

Yes (Small size) 1 ★

F: Compression print on journal at REG/MGR/VOID mode F

No (Normal size) 0

Yes (Small size) 1 ★

Note: This selection is valid only when “PRINTING FORMAT” isset as “JOURNAL”. This selection is not valid for the printing data of EJ report.It is provided another selection job for EJ.

G: Logo Text Print on Journal G

No 0 ★

Yes 1

H: FOOTER PRINT CONTROL H

ALL RECEIPTS 0 ★

ON SELECTED FUNCTION KEY AT THE TIMEOF FINALIZATION 1

A, B, C, D, E, F, G, H: Not used (Fixed at “00000000”)

A, B: Not used (Fixed at “00”)

C: Temporary journal printing function of transaction C

Disable 0

Enable 1 ★

Note: It is a function to print one transaction data which is notfinalized (during a transaction) when a transaction is oper-ated at “RECEIPT OFF”.It is available only at “RECEIPT PRINTER TYPE”.

D: EJ print and clear at general Z1 report D

No 0 ★

Yes 1

E: PGM mode programming operation records in EJ E

DETAIL 0 ★

Header information only 1

Note: It is not effected for PGM reading and XZ reports.PGM reading and XZ reports are always treatment as“HEADRER ONLY”.

F: REG/MRG/VOID operation records in EJ F

DETAIL 0 ★

TOTAL 1

G: Compression print for EJ report G

No (Normal size) 0

Yes (Small size) 1 ★

H: Action when EJ file is full H

Continue (No warning) 0

Warning (near full warning) 1 ★

Lock (with near full warning) 2

A, B, C, D, E: Not used (Fixed at “00000”)

F: TAX PRINTING WHEN TAXABLE SUBTOTAL IS ZERO F

No 0 ★

Yes 1

G: TAX PRINTING WHEN TAX IS ZERO G

Yes 0 ★

No 1

H: Not used (Fixed at “0”)

A: SPLIT PRICING COUNTING A

QUANTITY 0 ★

PACKAGE 1

B: MULTIPLICATION ENTRY SYSTEM B

MULTIPLICATION ONLY 0 ★

SPLIT PRICING & MULTIPLICATION 1

C, D: Not used (Fixed at “00”)

E: TAX PRINTING WHEN GST is VAT E

Yes 0 ★

No 1

F: GST EXEMPT on X/Z F

PRINTED 0 ★

NOT PRINTED 1

GH: TAX SYSTEM = 00 to 11

AUTO TAX = 00

CANADA TAX (GST TYPE nn) = 01 to 11

XE-A21S PROGRAM MODE

2 – 11

[JOB#71] GT2 PROGRAMMING -- XXXXXXXXXXXXX --

MRS = 0000000000000

XXXXXXXXXXXXX : GT (13digits)

[JOB#72] GT3 PROGRAMMING -- XXXXXXXXXXXXX --MRS = 0000000000000

XXXXXXXXXXXXX : GT (13digits)

[JOB#76] GENERAL Z1 RESET REPORT COUNTER -- XXXX --MRS = 0000

XXXX : RESET COUNTER (4digits)

[JOB#77] GENERAL Z2 RESET REPORT COUNTER -- XXXX --MRS = 0000

XXXX : RESET COUNTER (4digits)

[JOB#86] TRAINING CLERK PROGRAMMING -- XX --MRS = 0

X : CLERK No. = 0 (INHIBIT), 1 to 25

23) DOMESTIC CURRENCY SYMBOL PROGRAMMING

(CHARACTERS): CHARACTER (Max. 4 Characters)

Characters can be entered by using the character layout on keyboard orusing numeric keys on keyboard.THE KEY ENTRY SEQUENCE FOR ENTERING ONE CHARACTERBY NUMERIC KEYS IS AS FOLLOWS:

YYY 3 [00] KEYYYY : CHARACTER CODE (3 DIGITS)(or [000] KEY ACCORDING TO PGM PRESET)

MRS = ___$ ( _ : space code)

This symbol is printed with (+) amount of domestic currency.The programmed characters is printed at left side of amount.

Ex) Case of “ US$ ”: | DEPT.01 US$1.00 | 2 Programmed symbol

If some space characters are programmed at the left side of symbol(like “ $”), they are not counted as the number of character of the cur-rency symbol. (In case of “ US$”, the number of character is 3.)

Ex) Case of “ US$”: (The currency symbol means “US$”) |AAAADEPARTMENT01 US$10000.00 | 2 Programmed symbol

24) TRAINING MODE TEXT PROGRAMMING

(CHARACTERS): CHARACTER (Max. 8 characters)

Characters can be entered by using the character layout on keyboard orusing numeric keys on keyboard.THE KEY ENTRY SEQUENCE FOR ENTERING ONE CHARACTERBY NUMERIC KEYS IS AS FOLLOWS:

YYY 3 [00] KEYYYY : CHARACTER CODE (3 DIGITS)(or [000] KEY ACCORDING TO PGM PRESET)

MRS = TRAINING

25) TEXT CHANGING (TO DEFAULT TEXT)

X: 0 = English text3 = Spanish text

MRS = 0

When this job is executed, below texts are set as default data.

(a) Function text(b) Each message text (LOGO, etc..)

26) RESETTING OF ALL COUNTER AND TOTALIZER

All counter, totalizer, EJ data all GTs, and all Z counter are reset.

(CHARACTERS)SBTL SBTL85 CA/AT

NO CHANGE

(CHARACTERS)SBTL SBTL87 CA/AT

XSBTL @/FOR88 CA/AT

0

HEADER

*PGM* MODE TITLE

LANGUAGE MODE

05/02/2006 12:34PM

123456#1234

DATE/TIME/CLERK NO

MACHINE NO. /CC-NO. /CLERK NAME

#88 0

01

BETTY___

SBTL 89 CA/TL@/FOR

HEADER

*PGM* MODE TITLE

JOB#

05/02/2006 12:34PM

123456#1234

DATE/TIME/CLERK NO

MACHINE NO. /CC-NO. /CLERK NAME

#89

01

BETTY___

XE-A21S PROGRAM MODE

2 – 12

27) CHANGING MEMORY TYPE(EJ RECORD AND PLU RECORD)

X : 0 = TYPE1 (EJ: 2000 records and PLU 1200 records)1 = TYPE2 (EJ: 3000 records and PLU 210 records)

MRS = 0

When this job is executed, EJ records are deleted and PLU records areset the default data after deleted all records even if same memory typeis entered.

28) MAXIMUM NUMBER OF DEPARTMENTT

XX : Max Number of DEPARTMENT

This job is used for the limitation of below functions.

(1) Programming for the department code over the maximum num-ber of department.

(2) Registration for the department code over the maximum num-ber of department.

(3) Registration for the PLU that is associated to department overthe maximum number of department.

(4) Printing for the department data over the maximum number ofdepartment at PGM READING and XZ REPORTS.

MRS = 99

29) SD CARD FUNCTION

[Key Sequence of SD Jobs]

(*1) When [SBTL] key is pushed, ECR prints the confirmation messageat “RECEIPT” (not print at JOURNAL) and enforces to select eitherexecuting or canceling this job. The buffered keys are cleared.

(*2) “1” is a keyword to execute this job.

(*3) If the MODE SWITCH is turned to another mode from PGM positionor the AC POWER is off when job is executed, the job is cancelled.

Note: If AC POWER is off when ECR accesses SD CRAD, the contentsin SD CARD may be broken.

The action of each job is as below.

[JOB#140] Format SD CARD

This job formats SD card. (It deletes all data on SD card.)After formatting card, the folder \SHARP\ECRXXX01 is made to a rootdirectory.And then, \ALL, \PROGRAM, \SALES, \EJPRINT, \EJ and \LOGO aremade to a folder “\SHARP\ECRXXX01”.The file “SRECORD.REC” is made to both folder“\SHARP\ECRXXX01\SALES” and “\SHARP\ECRXXX01\EJ”and it is set the default data.Notes: • All the data currently written in SD card is erased.

• The file “SRECORD.REC” is used for control the structureunder each folder.Any users dose not need to concern itscontents.

[JOB#141] Programming data saving to SD CARD

[JOB#147] Programming Data loading from SD CARD

The below data is saved or loaded. Files are set in the folder for “Programming Data”.

(*1) The contents of each file are same as the communication data of“ONLINE FUNCTION”. Details of “File No.” and “Table No.” are described in “ONLINE SPECIFICATION”. All data are converted touse at “Customer Support Tool” software on PC.

Notes: • If there is data of the same file name, the message of confir-mation does not display.Data is overwritten if there is data of the same file name.

• Each files are used only for the “Customer Support Tool” soft-ware on PC. Any users dose not need to concern its contents.

xxx : JOB code

140 : Format SD CARD

141 : Save Programming Data (ECR 3 SD)

144 : Save All RAM Data (ECR 3 SD)

145 : Load Graphic Logo Data (ECR 1 SD)

147 : Load Programming Data (ECR 1 SD)

148 : Load All RAM Data (ECR 1 SD)

XSBTL @/FOR90 CA/AT

HEADER

*PGM* MODE TITLE

MEMORY TYPE (0: TYPE1, 1: TYPE2)

05/02/2006 12:34PM

123456#1234

DATE/TIME/CLERK NO

MACHINE NO. /CC-NO. /CLERK NAME

#90 0

01

BETTY___

XXSBTL @/FOR95 CA/AT

xxx 1@/FOR CA/AT

CL

SBTLSBTL

(*1) (*2)

: Execute operation (*3)

: Cancel

File Name File/Table No. (*1) Field (*1)

1 Date and Time mtimtbl D0

2 Department deptdata 01 B000(Label, Preset, Price, Text)

3 PLU pludata 11 B000(Label, Preset, Price, Text)

4 Function programming

FuncText A4

Mfunctbl D8

5 Tax Table andRate

mtaxtbl D7

6 Logo message mlgxtbl D2

7 Clerk CsrData 51 All fields

8 Others Programming

mopttbl D1

XE-A21S PROGRAM MODE

2 – 13

[JOB#145] Graphic logo data loading

The below data is loaded. Files are set in the folder for “LOGO Data”.

(*1) The contents of each file are same as the communication data of“ONLINE FUNCTION”. Details of “File No.” and “Table No.” aredescribed in “ONLINE SPECIFICATION”. All data are converted touse at “Customer Support Tool” software on PC.

Note: Files are created only for the “Customer Support Tool” softwareon PC. Any users dose not need to concern its contents.

[JOB#144] All Data Saving

[JOB#148] All Data LoadingNotes: • In case of “DATA SAVING”, the message of confirmation for

overwritten the file on SD Card does not display. Data is over-written if there is data of the same file name.

• In case of “DATA LOADING”, the condition of ECR will returnto past condition. However, the message of confirmation foroverwritten does not display.

The below data is saved or loaded. Files are set in the folder for “ALLRAM BACKUP”.

Note: Each files are used only for the purpose of DATA BACKUP atECR. Any users dose not need to concern its contents.

■ DISPLAY AND PRINT:

File Name File/Table No. (*1) Field (*1)

1 Graphic LOGO LOGO E0

File Name

1 All RAM data All

Key Display Print NOTE

1 2 3 4 5 6 7 8 9 0

[STBL] P

141 P 1 4 1

[@/FOR] P 1 4 1

[SBTL] P -The buffered keys are cleared and the message isprinted on “receipt” only. (It is not print on “journal” and “EJ”.)

MESSAGE : MAX 8-lines(The message is fixed in ROM.)

(Not count up CC# at this time.)

[1] P 1

[CA/AT] S d - A C C E S S . (Count up CC#.)DISPLAY : “.” is blinking while executing job.

PRINT : JOB HEADDER is printed.And job code is printed.(Job code is printed only at SD jobs)

(SD ACCESS) S d - A C C E S S . DISPLAY: “.” is blinking while executing job. PRINTPRINT : (NON)

Case of NORMAL END 0. 0 0 DISPLAY: (INITIAL)PRINT : STATUS is printed(The message is fixed in ROM.)

Case of ERROR END E - S d - 0 1 DISPLAY: ERROR CODE (2-digits)PRINT : SD ERROR MESSAGE and ERROR

CODE (The message is fixed in ROM.)

Case of CHANGINGMODE KEY (to cancel)

0. 0 0 DISPLAY: (INITIAL)PRINT : SD CANCEL MESSAGE(The message is fixed in ROM.)

Case of POWER OFF E - S d - P. O F F DISPLAY: ERROR MESSAGEPRINT : MESSAGE of POWER OFF(The message is fixed in ROM.)

123456789012345678901234

(PRE-PRINT HEADDER)! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! !YOU SELECT SD CARD JOBPUSH [1]-KEY to EXECUTEPUSH [CL]-KEY to CANCEL! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! !

Don't turn the mode keywhile executing a job.

! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! !(Issuing Receipt)

HEADER

*PGM*

05/02/2006 12:34PM

123456#1234

#141

01

BETTY___

***NORMAL END

(Issuing Receipt)

SD ERROR

(Issuing Receipt)

01

SD CANCELED

(Issuing Receipt)

POWER OFF ERRORAT THE DEVICE CONTROLSET DATA&TIME AGAIN

(Issuing Receipt)

XE-A21S PROGRAM MODE

2 – 14

3. CHARACTER ASSIGNMENT METHOD

■ PROGRAMMING KEY LAYOUT

Note: The small characters on the bottom or lower right in each key indications or characters which can be used for character entries for text programming.

■ THE METHOD OF CHARACTER ENTRY AT TEXT PROGRAMMINGThe character can be entered by using character key or character code.

When the character can be entered in the text programming, the key layout is changed from “Function and [DEPT] key layout” to “CHARACTER KEYLAYOUT”.

In “CHARACTER KEY LAYOUT”, any key except the Numeric keys and [CL], [SBTL], [CA/AT] are assigned either the character or the control key forcharacter entry.

Any character can be entered by following method.

By character key:

By Numeric key (Character Code) :

(The list of Control Key)

The status of [SHIFT], [NUMBER] and [DC] are keeping until pushing same control key in each text entry. (STAY DOWN type)

And the corresponding indication is lighted up on the display while their status is “on”.

(Example)

Key Action

SHIFT Entry to shift the following character key. (ex. [SHIFT] 3 [A] : Enter the character “a”.)

NUMBER Entry the following numeric key as the number character. (ex. [NUMBER] 3 [1] : Enter the character “1”.)

(DC) Double size character: Change the following character to the double size character.

BS Back Space : Delete the last character.

[SHIFT] 3 [A] [B] [C] 3 [SHIFT] 3 [A] [B] [C] : Text “abcABC”.

[NUMBER] 3 [1] [2] [3] 3 [NUMBER] 3 [1] [2] [3] : Text “123” and numeric number 123.

[DC] 3 [A] [B] [C] 3 [DC] 3 [A] [B] [C] : Text “ABCABC”.

: Characters on Character key layout.

: Numeric character ("0"), "1", . . . , "9")

SHIFT (CHARACTER KEY)

NUMBER (NUMERIC KEY)

xxx [00]

xxx : Character Code

XE-A21S PROGRAM MODE

2 – 15

Printer

CODE CHARACTER

001 á

002 â

003 ê

004 î

005 ì

006 í

007 ô

008 ó

009 û

010 ú

011 œ

012

013 ú

014

015 ó

016 Λ

017 Ψ

018 Γ

019 ..

020 Ω

021 ∆

022 Θ

023 Ξ

024 Π

025 Σ

026 Υ

027 Φ

028

029 Ú

030

031 Ó

032 (Space)

033 !

034 "

035 #

036 $

037 %

038 &

039 '

040 (

041 )

042 *

043 +

044 ,

045 –

046 .

047 /

048 0

049 1

050 2

051 3

052 4

053 5

054 6

055 7

056 8

057 9

058 :

059 ;

060 <

061 =

062 >

063 ?

064 @

065 A

066 B

067 C

068 D

069 E

070 F

071 G

072 H

073 I

074 J

075 K

076 L

077 M

078 N

079 O

080 P

081 Q

082 R

083 S

084 T

085 U

086 V

087 W

088 X

089 Y

090 Z

091 Ä

092 Ö

093 Ü

094 ^

095 _

096

097 a

CODE CHARACTER

098 b

099 c

100 d

101 e

102 f

103 g

104 h

105 i

106 j

107 k

108 l

109 m

110 n

111 o

112 p

113 q

114 r

115 s

116 t

117 u

118 v

119 w

120 x

121 y

122 z

123 {

124 |

125 }

126 ß

127

128 !!

129 1

130 2

131 3

132 4

133 1/2134 F T135 1

136 3

137 p

138 p

139 d

140 e

141 F

142 T

143 4

144 ç

145 O

146 ¿

CODE CHARACTER

147 ù

148 à

149 Æ

150 φ

151 Å

152 ¤

153 é

154 è

155 Pt

156 ¡

157 Ñ

158 Õ

159 £

160 ¥

161

162

163

164

165 .

166 T 1167 T 2168 T 3169 T 4170 1 2171 1 3172 1 4173 2 3174 2 4175 3 4176

177 Á

178

179

180 A

181 a

182 E

183 e

184 I

185 i

186 U

187 u

188

189

190

191 Š

192

193

194

195

CODE CHARACTER

196

197

198

199

200

201

202

203

204

205

206

207

208 P

209

210

211 š

212

213

214

215

216

217

218

219

220

221

222

223

224 *

225 §

226 Ø

227 ^

228 2

229 ]

230 [

231

232 ä

233 ö

234 ü

235 æ

236 å

237 É

238 ñ

253 (DC)

CODE CHARACTER

Note: The character of this table is for reference. Please see actual display.(DC) : Double Code : ECR Control Character (Not used for text)

XE-A21S PROGRAM MODE

2 – 16

4. HELP FUNCTION

This function prints guidance messages of main cash register functions

by pushing the HELP key. If you push a number key and the HELP key

following the guidance messages, more detailed guidance messages

will be printed.

[PURPOSE]

The aim is to be able to easily program the register by printing the guid-

ance messages.

[PROGRAMMING]

(PGM-mode)

Follow the setup features below for the desired HELP printing settings.

JOB#6-A : Printer format receipt/journal.

JOB#66-E : Compression print on journal at PGM/XZ mode Small size/

Normal size.

JOB#66-F : Compression print on journal at REG/MGR/VOID mode

Small size/Normal size.

(REG/MGR-mode)

Even if ECR is in a receipt-off state, HELP printing is executed.

(Other)

HELP printing is written in electronic journal.

[OPERATION]

1. Available Mode of Help function

PGM, VOID, O/P X/Z, REG, MGR, X1/Z1, X2/Z2

2. The proper timing of when the HELP function will work is when the

transaction is finalized, not during the transaction operation.

Key operating sequences

If [HELP] key is pressed on the ECR, the following receipt is printed.

1-[HELP]: DATE/TIME

key No. Print menu

[HELP] 1 Date/Time setup

2 Rate of TAX setup

3 Department setup

4 Sales Z report

5 Logo setting

6 Receipt issue

7 What is P in Display

8 What is ERROR 32

9 SD card command

10 Install PC software

XX HELP

Help Menu

Help No.

HEADER

05/02/2006 12:34PM 01123456#1234 BETTY___

HELP MENU

1-[HELP]: DATE/TIME2-[HELP]: TAX3-[HELP]: DEPARTMENT4-[HELP]: SALES Z REPORT5-[HELP]: LOGO6-[HELP]: RECEIPT7-[HELP]: P IN DISPLAY8-[HELP]: ERROR 329-[HELP]: SD CARD10-[HELP]: PC S/W INSTALL------------------------OTHER ISSUE: PLEASE CALL 1-800-BE-SHARP

MACHINE NO. /CC-NO. /CLERK NAME

MODE TITLE

DATE/TIME/CLERK NO

DATE/TIME/CLERK NO MACHINE NO./CC-NO./CLERK NAME

MODE TITLE

(PGM MODE)DATE:XXXXXXXX-[SBTL] YYYYMMDD OR DDMMYYYY OR MMDDYYYY(DEFAULT)TIME:HHMM-[SBTL] (0000-2359)EX) 08/01/2006 PM4:30 (DATE FORMAT=M-D-Y) 08012006-[SBTL]1630-[SBTL]

05/02/2006 12:34PM 01123456#1234 BETTY___

1 DATE/TIME SETUP

HEADER

XE-A21S PROGRAM MODE

2 – 17

2-[HELP]: TAX

3-[HELP]: DEPARTMENT

4-[HELP]: SALES Z REPORT

5-[HELP]: LOGO

HEADER

05/02/2006 12:34PM 01 123456#1234 BETTY___

2 TAX RATE SETUP

(PGM MODE)

R:RATE(0.0000-100.0000%)

[SBTL]-9-[@]-N-[@]-R-[@]-Q-[SBTL]-[CA]

EX) TAX1(RATE=6.25%),

Q:MIN. TAXABLE AMOUNT

-[@]-300-[SBTL]-[CA]

MIN. AMT=$3.00[SBTL]-9-[@]-1-[@]-6.25

MACHINE NO. /CC-NO. /CLERK NAME

MODE TITLE

N:TAX NUMBER (1-4)

(0.00-999.99)

DATE/TIME/CLERK NO

DATE/TIME/CLERK NO MACHINE NO./CC-NO./CLERK NAME

MODE TITLE

(PGM MODE)1)PRICEXX-[DEPT#]-YYYYYY- [SBTL]-[CA]XX:DEPARTMENT CODE(1-99)YYYYYY:UNIT PRICE (MAX.6DIGITS)2)TEXT[SBTL]-1-[.]-XX-[DEPT#]-(TEXT)-[SBTL]-[CA]XX:DEPT CODE(1-99)TEXT CAN BE ENTERED BYUSING THE CHARACTERLAYOUT ON KEYBOARD ORNUMERIC KEY ON KEYBOARD.

05/02/2006 12:34PM 01123456#1234 BETTY___

3 DEPARTMENT PRICE&TEXT

HEADER

DATE/TIME/CLERK NO MACHINE NO./CC-NO./CLERK NAME

MODE TITLE

SALES Z REPORT SHOWS THEDAILY/ PERIODIC SALES1. DAILY Z REPORT(X1/Z1 MODE) [.]-[CA]: GENERAL [.]-[PLU]: PLU [.]-[CLK#]: CLERK [.]-[SBTL]: HOURLY2. PERIODIC Z REPORT(X2/Z2 MODE) [.]-[CA]: GENERAL

05/02/2006 12:34PM 01123456#1234 BETTY___

4 SALES Z REPORT

HEADER

HEADER

05/02/2006 12:34PM 01123456#1234 BETTY___

5 LOGO SETTING

(PGM MODE)1)LOGO FORMAT[SBTL]-11-[@]-A-[SBTL]- [CA]A=0:3LINE HEADER 1:GRAPHIC LOGO ONLY 2:GRAPHIC+3LINE FOOTER 3:6LINE HEADER 4:GRAPHIC+3LINE HEADER 5:3LINE HEADER/FOOTER2)LOGO TEXT[SBTL]-4-[.]-L-[@]- (TEXT)-[SBTL]-[CA]L:LINE NUMBER(1-6)TEXT CAN BE ENTERED BYUSING THE CHARACTERLAYOUT ON KEYBOARD ORNUMERIC KEY ON KEYBOARD.3)GRAPHIC LOGOPLEASE REFER TOCUSTOMER SUPPORT TOOL

MACHINE NO. /CC-NO. /CLERK NAME

MODE TITLE

DATE/TIME/CLERK NO

XE-A21S PROGRAM MODE

2 – 18

6-[HELP]: RECEIPT

7-[HELP]: P IN DISPLAY

8-[HELP]: ERROR 32

9-[HELP]: SD CARD

10-[HELP]: PC S/W INSTALL

DATE/TIME/CLERK NO MACHINE NO./CC-NO./CLERK NAME

MODE TITLE

05/02/2006 12:34PM 01123456#1234 BETTY___

6 RECEIPT ISSUE

WHETHER ISSUE RECEIPT ORNOT CAN BE CHANGED BYDEPRESSING [RCPT] KEYIF THE INDICATOR "_" APPEARS ONDISPLAY, RECEIPT IS NOTISSUED, IN THIS CASE,DEPRESSING [RCPT] KEY WILL ENABLE RECEIPTPRINT AGAIN

HEADER

DATE/TIME/CLERK NO MACHINE NO./CC-NO./CLERK NAME

MODE TITLE

05/02/2006 12:34PM 01123456#1234 BETTY___

7 WHAT IS P IN DISPLAY

[ERROR STATUS]

PAPER EMPTY[RESOLUTION]

INSERT NEW ROLL PAPER

HEADER

HEADER

DATE/TIME/CLERK NO MACHINE NO./CC-NO./CLERK NAME

MODE TITLE

05/02/2006 12:34PM 01

123456#1234 BETTY

8 WHAT IS ERROR 32

[ERROR STATUS]

NO ENTRY OF CLERK CODE[RESOLUTION]

ENTER A CLERK CODE

EX) ENTRY OF CLERK #1

1-[CLK#]

DATE/TIME/CLERK NO MACHINE NO./CC-NO./CLERK NAME

MODE TITLE

05/02/2006 12:34PM 01123456#1234 BETTY___

9 SD CARD COMMAND

(PGM MODE)[SBTL]-XXX-[@]-[SBTL]

XXX=140:FORMAT141:SAVE PROGRAMMING144:SAVE ALL RAM145:LOAD GRAPHIC LOGO147:LOAD PROGRAMMING148:LOAD ALL RAM(X1/Z1 MODE)

SAVE SALES DATA 650-[.]-[@]-[SBTL]

SAVE AND CLEAR EJ DATA 750-[.]-[@]-[SBTL]

PRINT EJ DATA ON SD 740-[@]-[SBTL]

HEADER

DATE/TIME/CLERK NO MACHINE NO./CC-NO./CLERK NAME

MODE TITLE

05/02/2006 12:34PM 01123456#1234 BETTY___

10 INSTALL PC SOFTWARE

1.INSERT CUSTOMER SUPPORT CD IN YOUR PC2.INSTALLATION PROGRAM RUNS AUTOMATICALLY(FOR USB CONNECTION)

3.AFTER INSTALLATION OF SOFTWARE,-TURN OFF ECR-CONNECT PC AND ECR VIA USB CABLE-TURN ON ECR-SELECT "INSTALL THE SOFTWARE AUTOMATICALLY" AT HARDWARE WIZARD

HEADER

XE-A21S PROGRAM MODE

2 – 19

CHAPTER 3. OP X/Z, X1/Z1, X2/Z2 MODE

Roughly speaking, the following sales reports are available:

1) OP X/Z reports (Individual cashier reports)

2) X1/Z1 reports (Daily total X and Z reports)

3) X2/Z2 reports (Periodic total X and Z reports)

4) Flash-read reports (Display sales amount)

In addition to the above reports that are to be used for program check-ing are also available.

[Purpose]The reports are each used to check sales data. The standard purposesof taking these reports are as follows:

OP X/Z reports : These reports are taken by operators in order toreport their own sales data.

X1/Z1 reports : These reports are taken by the supervisor or manager inorder to check and report daily sales totals at that point.

X2/Z2 reports : These reports are taken by the owner or manager inorder to check and report periodic (weekly or monthly)totals.

Flash-read : These reports are taken by the owner or manager inorder to check and display sales totals at that point.

[Operation]

In the table below those reports marked with a circle “ ” can be executed.

PRINTING REPORT

FLASH READING REPORT

OTHERS OPERATION

REPORT NAME KEYENTRY

MODE

DATA FOR READINGOPX/Z X1/Z1 X2/Z2

X Z X1 Z1 X2 Z2

GENERAL [CA/AT] *1, *6

PLU BY RANGE [PLU] PLU CODE *1, *2

CRERK (ALL) [CLK]# *1

CRERK (INDIVIDUAL) [CLK]# *1, *3

HOURLY (ALL) [#/SBTL] *1

REPORT NAME KEY ENTRY

MODE

DATA FOR READINGOPX/Z X1/Z1 X2/Z2

X Z X1 Z1 X2 Z2

DEPARTMENT [DPTn]or [SHIFT] 3 [DPTn]or NK 3 [DEPT#] DEPT CODE

*4

CID [@/FOR] *4

PAID TOTAL [CA/AT] *4

REPORT NAME JOB#

MODE

DATA FOR READINGOPX/Z X1/Z1 X2/Z2

X Z X1 Z1 X2 Z2

EJ report (ALL) 700 *5, *6

EJ report (Latest 10 records) 710 *5, *6

MODE: X : Daily operater X report Z : Daily operater Z report

X1 : Daily X report Z1 : Daily Z report

X2 : Periodic X report Z2 : Periodic Z report

(X report): The corresponding data is held in the ECR.

(Z report): The corresponding data is cleared in the ECR.

XE-A21S OP X/Z, X1/Z1, X2/Z2 MODE

3 – 1

• Stop of printing reports (Report cancel function):This ECR has the function of report stopping for PLU report and EJreport.

• Printing of GT on X reports:This ECR dose not print any GT on X reports.

*1 To read respective reports, it is necessary to follow the procedurebelow.

*2 PLU code range can be specified by entering the start and endnumbers according to the following procedure.When specifying a single PLU code, the start number has only to beentered.

*3 To read respective reports, it is necessary to follow the procedurebelow. The clerk code does not need to enter at the OPX/Z mode.In OPX/Z mode, it is issued the report of the assigned clerk.

*4 Reading display only.The displayed amount can be cleared by [CL] key.

*5 To read respective contents, it is necessary to follow the procedure below.

*6 It is able to print and clear the EJ memory at general Z1 report byPGM mode programming.In that case, the contents of EJ memory is printed just after issuedgeneral Z1 report.(Issuing general Z1 report 3 Clear daily DEPT & TRANS memory 3Issuing EJ memory 3 Clear EJ memory)

[Action]

Individual counters for the following Z reports are incremented whenthose reports are printed.

1) General daily total report (Z1)

2) General periodic total report (Z2)

[Additional function]

(1) Overflow markIf the amount or quantity in any totalizer other than GT to be printedon X or Z reports exceeds a programmed limit, the indication mark(overflow mark) is printed for the totalizer concerned.The overflow mark may be printed even if a totalizer does not reachthe maximum amount. This occurs, for example, when the amountor quantity in the totalizer gets smaller than the maximum amountdue to the entry of a negative amount after the overflowing of thetotalizer. This means that when the totalizer overflows once, theoverflow mark (for example, “!!”) is printed.

(2) MODE TITLEEach report is printed MODE TITLE at a header of report.The Report Titles are as follows.

(3) Report cancel functionIt can be cancelled by turned the mode switch to MGR position while the data is printed. (In this case, the contents of memory arenot cleared.)

(X report)Reading

Resetting(Z report)

KEY

Start No.XXXX XXXX

End No.

All

PLU@/FOR

Resetting

Reading

CLKEY

(Display amount) (Display initialize)

JOB# @/FOR CA/AT

Resetting

Reading

OPX report *OPX*

OPZ report *OPZ*

X1 report *X1*

Z1 report *Z 1*

X2 report *X2*

Z2 report *Z 2*

::

* * * * * 1 the report cancel symbol

123456789012345678901234

XE-A21S OP X/Z, X1/Z1, X2/Z2 MODE

3 – 2

ELECTRONIC JOURNAL REPORT

This job is own to print and clear EJ memory in X1/Z1 mode and OPXZ mode.

[Key sequence]

1) Reading and resetting of all records:[OPXZ, X1/Z1 mode]

2) Reading of the latest 10 records:[OPXZ, X1/Z1 mode]

[ACTION]

It prints all or parts of printing data in EJ memory.The printing format is same as each operation.

It is able to print and clear the EJ memory at general Z1 report by PGMmode programming.In that case, the contents of EJ memory is printed just after issued gen-eral Z1 report.(Issuing general Z1 report 3 Clear daily DEPT & TRANS memory 3Issuing EJ memory 3 Clear EJ memory)

[Report cancel function]

It can be cancelled by turned the mode switch to MGR position while EJdata is printed. (In this case, the contents of EJ memory are not cleared.)

[Key Sequence of SD Jobs]

(*1) When [SBTL]-key is pushed, ECR prints the confirmation message at “RECEIPT” (not print at JOURNAL) and enforces toselect either executing or canceling this job. The buffered keys arecleared.

(*2) “1” is a keyword to execute this job.

(*3) If the MODE SWITCH is turned to another mode from X1Z1 position or the AC POWER is off when job is executed, the job iscancelled.

Note: If AC POWER is off when ECR accesses SD CRAD, the contentsin SD CARD may be broken.

The action of each job is as below.

[JOB#650] Sales data saving

All sales data (Daily and term) save in SD card.This job is used for the purpose of using Electric Journal Data at the“Customer Support Tool” software on PC. Maximum 400 times data iskept in SD Card when the SD memory is not full.

The action is as below.

Step1) After reading the information of the current sub-folder in“SRECORD.REC” file, ECR creates the new sub-folder underthe folder for “Sales Data”.Its folder is named ASCII Character that is indicated the numberof sales data in SD Card. (Example: “1”, “2”, “3”,......)

Step2) Save the below data in new sub-folder that is created above step.

Spet 3) Create the “STATUS.REC” file in new sub-folderwhen all files are saved completely.

Step 4) Update the “SRECORD.REC” file for changing the structure ofsub-folder.

(*1) The contents of each file are same as the communication data of“ONLINE FUNCTION”. Details of “File No.” and “Table No.” aredescribed in “ONLINE SPECIFICATION”. All data are converted touse at “Customer Support Tool” software on PC.

Note: Each files are used only for the “Customer Support Tool” soft-ware on PC. Any users dose not need to concern its contents.

[JOB#750] Electric Journal Saving and Clearing on memory

Electric journal data is saved in SD card.This job is used for the purpose of using Electric Journal Data at the“Customer Support Tool” software on PC. Maximum 400 times data iskept in SD Card when the SD memory is not full.

Note: After saving EJ data, ECR is clear the Electronic Journal memory.

xxx: JOB code

650: Save Sales Data (ECR 3 SD)

750: Save and Clear EJ Data (ECR 3 SD)

yyy: JOB code

740: Printing EJ Data on SD (ECR 1 SD)

CA/AT@/FOR

(Reading)

(Reseting)700

710 @/FOR CA/AT

xxx 1

yyy

@/FOR CA/AT

CL

SBTL

(*1) (*2)

: Execute operation (*3)

: Cancel

File Name File/Table No. (*1) Field (*1)

1 Date and Time(When a job is operated)

mtimtbl D0

2 Department Sales Dept 01 All fields

3 Transaction Sales Trans 21 All fields

Func Text A4

4 Hourly Sales Hourly 61 All fields

5 Clerk Sales Csr Data 51 All fields

Csr Sal 52 All fields

6 PLU Sales Plu 11 All fields,All range1

File Name

1 Status information STATUS.REC

File Name

1 Record structure SRECORD.REC

750 @/FOR CA/AT

XE-A21S OP X/Z, X1/Z1, X2/Z2 MODE

3 – 3

The action is as below.

Step1) Save the below data in the folder for “Electric Journal for printing”.

Step2) After reading the information of the current sub-folder in“SRECORD.REC” file, ECR creates the new sub-folder underthe folder for “Electric Journal Data”.Its folder is named ASCII Character that is indicated the numberof sales data in SD Card. (Example: “1”, “2”, “3”,......)

Step3) Save the below data in new sub-folder that is created above step.

Spet4) Create the “STATUS.REC” file in new sub-folder when all files are saved completely.

Step5) Update the “SRECORD.REC” file for changing the structure of sub-folder.

Step6) Clear EJ DATA on memory at ECR.

(*1) The contents of each file are same as the communication data of“ONLINE FUNCTION”. Details of “File No.” and “Table No.” aredescribed in “ONLINE SPECIFICATION”. All data are converted touse at “Customer Support Tool” software on PC.

Notes: • The file in the EJPRINT folder on SD Card is overwritten.The message of confirmation for overwritten the file in theEJPRINT folder on SD Card does not display.

• Each files are used only for the “Customer Support Tool” soft-ware on PC. Any users dose not need to concern its contents.

[JOB#740] Electric journal print

ECR prints the below data that is already set in the folder for “EJPRINT Data”.

(*1) The contents of each file are same as the communication data of“ONLINE FUNCTION”. Details of “File No.” and “Table No.” aredescribed in “ONLINE SPECIFICATION”. All data are converted touse at “Customer Support Tool” software on PC.

Notes: • It is printed only the newest EJ DATA (That is saved at last byeither ECR or PC).

• Each files are used only for the “Customer Support Tool” soft-ware on PC. Any users dose not need to concern its contents.

■ DISPLAY AND PRINT: X1/Z1 MODE)

JOB ENTRY OPERATION: (Common action for all Jobs)

--- Continue to JOB END MESSAGE (NEXT PAGE)

File Name File/Table No. (*1) Field (*1)

1 EJ Data EJFILE A0

File Name File/Table No. (*1) Field (*1)

1 EJ Data EJFILE A0

File Name

1 Status information STATUS.REC

File Name

1 Record structure SRECORD.REC

File Name File/Table No. (*1) Field (*1)

1 EJ Data EJFILE A0

Key Display Print NOTE

1 2 3 4 5 6 7 8 9 0

750 [ . ] 7 5 0.

[@/FOR] 7 5 0.

[SBTL] - The buffered keys are cleared and the message isprinted on “receipt” only. (It is not print on “journal” and “EJ”.)

MESSAGE: MAX 8-lines(The message is fixed in ROM.)

(Not count up CC# at this time.)

[1] 1

[CA/AT] S d - A C C E S S . (Count up CC#.)DISPLAY: “ . ” is blinking

while executing job.PRINT : JOB HEADDER is printed.

And job code is printed.(Job code is printed only at SD jobs)

Case of EJ PRINT:The EJ DATA is printed as same as EJREPORT (#700) after printing job code.

(SD ACCESS) S d - A C C E S S . DISPLAY : “ . ” is blinkingwhile executing job.

PRINT : (NON)

::

123456789012345678901234

(PRE-PRINT HEADDER)! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! !YOU SELECT SD CARD JOBPUSH [1]-KEY to EXECUTEPUSH [CL]-KEY to CANCEL! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! !

Don't turn the mode keywhile executing a job.

! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! !(Issuing Receipt)

HEADER

*Z1*

05/02/2006 12:34PM

123456#1234

#750

01

BETTY___

XE-A21S OP X/Z, X1/Z1, X2/Z2 MODE

3 – 4

[JOB END MESSAGE] Case of DATA SAVING (“SALES” or “EJ DATA”):

The messages are printed on both RECEIPT and JOURNAL and recorded in EJ memory.

[JOB END MESSAGE] Case of EJ DATA PRINTING:

The report cancel symbol is printed on both RECEIPT and JOURNAL, but it is not recorded in EJ memory.The messages except the report cancel symbol are printed on both RECEIPT and JOURNAL and recorded in EJ memory.

[ERROR CODE LIST]

Key Display Print NOTE

1 2 3 4 5 6 7 8 9 0

NORMAL END 0. 0 0 DISPLAY: (INITIAL)PRINT : STATUS is printed (The message is fixed in ROM.)

ERROR END E - S d - 0 1 DISPLAY: ERROR CODE (2-digits)PRINT : SD ERROR MESSAGE and ERROR CODE(The message is fixed in ROM.)

CANCEL(CHANGING MODEKEY)

0. 0 0 DISPLAY: (INITIAL)PRINT : SD CANCEL MESSAGE(The message is fixed in ROM.)

POWER OFF E - S d - P. O F F DISPLAY: ERROR MESSAGEPRINT : MESSAGE of POWER OFF(The message is fixed in ROM.)

123456789012345678901234

***NORMAL END

(Issuing Receipt)

SD ERROR

(Issuing Receipt)

01

SD CANCELED

(Issuing Receipt)

POWER OFF ERRORAT THE DEVICE CONTROLSET DATA&TIME AGAIN

(Issuing Receipt)

Key Display Print NOTE

1 2 3 4 5 6 7 8 9 0

NORMAL END 0. 0 0 DISPLAY: (INITIAL)PRINT : (NON)

ERROR END E - S d - 0 1 DISPLAY : ERROR CODE (2-digits)PRINT : The report cancel symbol, SD ERROR

MESSAGE and ERROR CODE(The message is fixed in ROM.)

CANCEL(CHANGING MODEKEY)

0. 0 0 DISPLAY: (INITIAL)PRINT : The report cancel symbol and SD

CANCEL MESSAGE(The message is fixed in ROM.)

POWER OFF E - S d - P. O F F DISPLAY: ERROR MESSAGEPRINT : The report cancel symbol, POWER OFF

ERROR MESSAGE and Notes message(The message is fixed in ROM.)

123456789012345678901234

(Issuing Receipt)

SD ERROR 01* * * * * *

(Issuing Receipt)

SD CANCEL* * * * * *

(Issuing Receipt)

POWER OFF ERRORAT THE DEVICE CONTROLSET DATA&TIME AGAIN

(Issuing Receipt)

* * * * * *

No. Description

01 SD card is not find

02 SD CARD PROTECT SWITCH is set “PROTECED”

03 SD CARD WRITTING ERROR (Memory is full) (ECR cannot write the data on SD card.)

04 SD CARD READING ERROR (File is nothing)

05 SD CARD READING ERROR (File data is failed) (ECR cannot read the data on SD card.)

: >

10 Over limitation of data records (Over max record in sales or EJ data.)

: >

99 SD CARD ERROR (Anyhow error except above SD ERROR is occurred when ECRaccesses SD Card.)

XE-A21S OP X/Z, X1/Z1, X2/Z2 MODE

3 – 5

SHARP CORPORATIONInformation and Communication Systems GroupQuality Assurance DepartmentYamatokoriyama, Nara 639-1186, Japan

2006 November Printed in Japan t

COPYRIGHT 2006 BY SHARP CORPORATIONAll rights reserved.Printed in Japan.

No part of this publication may be reproduced,stored in a retrieval system, or transmitted.

In any form or by any means,

electronic, mechanical, photocopying, recording, or otherwise,without prior written permission of the publisher.

LEAD-FREE SOLDERCHAPTER 1. MASTER RESET and program reset1. Master resetting2. Program resetting (Initialization)

CHAPTER 2. PROGRAM MODE1. Reading Stored Programs2. USER PROGRAMMING3. Character assignment method4. HELP Function

CHAPTER 3. OP X/Z, X1/Z1, X2/Z2 MODEElectronic Journal Report