prof. k radhakrishna rao lecture 1 introduction to sensors, signals
TRANSCRIPT
Analog Circuits and Systems
Prof. K Radhakrishna Rao
Lecture 1 Introduction to Sensors, Signals and Systems
1
Some present day popular electronic products
o Cell phone
o Television
o Music system
o Radio
o Computers
o Watches and clocks
o Camera
o Medical instruments
o Printer
o ATM
o Home appliances
o Lighting
o Security systems
2
Electronic products: Sense and process signals (ECG)
o Sense, process, present o display audio output record oscilloscope and
o preserve processed signals o Storage in memory
3
Electronic products: Store information
4
Electronics Products: Output processed information in audio and or video form
5
Electronics Products: Activate/control devices using processed information
6
Electronics Products: Transmit and receive information
7
Electronic products
� Primary function is processing signals/data
Signals o Anything that carries
information is a signal ◦ Speech ◦ music ◦ scenery ◦ chirping of birds ◦ gestures
o chemical signals that control body functions
o Electronic products deal with electrical signals which are voltages and currents
8
Electronic products
Signals from real world o Electrical signals are derived from the real world through
transducers which convert a physical or chemical variable into an electrical signal
o Transducers produce analog signals which are continuous functions of independent variables
9
Strain Gage Bridge
¢ Vo+ = ((R+DR)/ 2R)Vexc
¢ Vo- = ((R-DR)/ 2R)Vexc ¢ Output Difference Signal =
(DR/R)Vexc, Output Common Mode Signal = Vexc/2
10
Some Transducers
11
Nature of Signals: Periodic Analog Signals
12
Problem
o Place your finger at the input terminal of an oscilloscope. What do you see?
o Ans: 50Hz/60Hz power line frequency signal.
13
Problem
o A periodic waveform is shown o Estimate the frequency and the harmonic content of the waveform.
14
Solution
0.1sin100 0.05sin300t tπ π+
15
Aperiodic Signals
16
Problem
o What can you say about the nature of the signal shown:
17
Spectrum and Bandwidth
o Spectrum is the distribution power as a function of frequency o Analog signals are characterized by their spectra. o The frequency range over which most of the signal power is
concentrated is called the bandwidth of the signal.
18
Spectra
19
Spectra
20
Problem
o Draw the spectrum of the following signal
( )( )5 sin1000 sin10000v t t=
21
Solution
( ) ( )sin sincos cos
2
A BA B A B− − +
=
Spectrum
22
Characteristics of some signals
o Speech signal has a band width of 300 Hz – 3 kHz o Video signal has a bandwidth of 25 Hz - 5 MHz to 100 MHz o HiFi music has a bandwidth of 20 – 30 kHz o ECG 0.04 to 150 Hz
23
Baseband Signal
o Some baseband signals of interest are biomedical, audio and video signals
o Baseband signals cannot be transmitted directly over long distances o Output from a transducer is used to modulate a carrier for
transmission over long distances
24
Noise
o Noise is unwanted electrical or electromagnetic energy that interferes with wanted signal
o When we measure ECG signal using electrodes, they also pick up the noise at 50/60 Hz
o When the ambient audience created noise is picked up by the microphone in a music performance
o Internal noise generated by the electronic components of the electronic circuit performing signal processing function
25
ECG Signal and 50/60Hz Noise
Noise dominating the signal
Narrow Band
26
Signal with Noise
Signal dominating the Noise
Narrow Band
27
Signal and Noise
o A signal is always contaminated by noise o The unwanted noise will have to be suppressed (filtering) or
reduced (cancellation) o Wanted signal may be strengthened with respect to noise
(amplification) o Improvement of signal-to-noise (S/N) ratio (SNR) is one of the
purposes of signal processing SNR = 10 log (signal power/noise power) decibels
28
Signal Processing
o Using a megaphone to communicate with a crowd (amplification) o Eliminating or reducing the ambient noise (filtering, and noise
cancellation and subtraction) o Selecting a radio station (selection) filtering (bandpass) o Smoke signal, Morse code, drum beats (coding/modulation, A/D
conversion/ multiplication) o Reading smoke signals and message sent by Morse Code
(Demodulation/Digital to Analog Conversion/ multiplication)
29
Analog signal processing
o Amplification of microphone output o Filtering 50 Hz interference from power line in ECG signal o Modulating a carrier with an audio signal (multiplication) o Storing music on a magnetic tape – as against this in digital it is
stored in memory
30
Why digital signal processing?
o Complexity and accuracy can be greatly improved if signals are processed in their digital coded form
o DSP leads to great reduction in cost, size, reliability and efficiency o Analog signals are encoded into digital form using analog-to-digital
converter o Powerful digital signal processing (DSP) devices are currently
available
31
Analog Circuits and Systems
Design of analog circuits and systems requires performing: o signal processing functions including, amplification, addition,
subtraction, integration, comparison, filtering and multiplication o signal generation o interfacing including sample and hold, A/D conversion and D/A
conversion o power supply management
32
Aim of the Course
The aim of the course ‘Analog Circuits and Systems’ is to design analog circuits and systems that perform signal processing functions, and signal generation using the devices including Op-Amps, amplifiers, multipliers and comparators.
33
Course Outcomes CO1 Understand the characteristics of linear one-port and two-port
signal processing networks CO2 Model one-port devices including R, L, C and diodes, two-port
networks, and active devices including amplifiers, Op Amps, comparators, multipliers, BJTs and FETs
CO3 Understand how negative and positive feedback influence the behaviour of analog circuits
CO4 Design VCVS, CCVS, VCCS, CCCS, and DC and SMPS voltage regulators
CO5 Design analog filters CO6 Design waveform generators, phase followers and frequency
followers
34
References
1. Applications of Operational Amplifiers: Third Generation Techniques (The BB electronics series); Jerald G. Graeme (Author); Mcgraw-Hill (Tx); First Edition 1973 https://archive.org/details/ApplicationsOfOperationalAmplifiers-3rdGenerationTechniques
2. Operational Amplifiers: Theory and Practice; James J Roberge; John Wiley & Sons; 1st Edition http://ocw.mit.edu/resources/res-6-010-electronic-feedback-systems-spring-2013/textbook/
3. Function circuits: design and applications; Yu Jen Wong, William E. Ott; McGraw-Hill, 1976
35