proel ms32 manual
TRANSCRIPT
-
8/18/2019 Proel MS32 Manual
1/57
PROELMS 32
PROGRAMMABLEMIDI SENDER
OWNER’S
MANUAL
-
8/18/2019 Proel MS32 Manual
2/57
2 Proel MS 32 Owner's Manual
INDEXSPECIFICATIONS....................................................................................................................... 3
MEMORY STRUCTURE ............................................................................................................ 4
MS 32 FRONT AND REAR VIEW ............................................................................................. 5
POWER ON.................................................................................................................................. 6
GLOBAL PARAMETERS........................................................................................................... 7POWER-ON NAME : ..............................................................................................................................................7
POWER-ON SET & PATCH RECALL : .................................................................................................................8BASIC RX MIDI CHANNEL : ................................................................................................................................9
FOOT CONTROLLER 1 CALIBRATION :........................................................................................................... 10FOOT CONTROLLER 2 CALIBRATION :........................................................................................................... 11CONTINUE SWITCH ASSIGNMENT:................................................................................................................. 12GLOBAL PARAMETERS FLOW CHART : .........................................................................................................13WRITE GLOBAL PARAMETER:.........................................................................................................................14
MODE......................................................................................................................................... 15
SET MODE................................................................................................................................. 16SET SELECTION (0~9): .......................................................................................................................................16START/STOP AND CONTINUE FUNCTIONS:................................................................................................... 17
NOTE:...................................................................................................................................................................17SET NAME : ........................................................................................................................................................19SONG SELECT :................................................................................................................................................... 20
"A" PART TX MIDI CHANNEL : .........................................................................................................................21"B" PART TX MIDI CHANNEL : .........................................................................................................................22SET PARAMETERS FLOW CHART:...................................................................................................................23
WRITE SET MEMORY: .......................................................................................................................................24
PATCH MODE........................................................................................................................... 250~9 PATCH SELECTION: ....................................................................................................................................25START/STOP AND CONTINUE FUNCTIONS: ..................................................................................................26EDIT PATCH PARAMETERS: .............................................................................................................................27
FC1 ASSIGN :........................................................................................................... ............................................28FC1 RANGE : .......................................................................................................................................................29FC2 ASSIGN :.......................................................................................................... .............................................30
FC2 RANGE : .......................................................................................................................................................31FC 1/2 LINK :........................................................................................................................................................32
PATCH BAY SWITCH 1-2 : .................................................................................................................................33PATCH BAY SWITCH 3-4 : .................................................................................................................................34A CHANNEL BANK SELECT CC00 & CC32 : ....................................................................................................35A CHANNEL PROGRAM CHANGE :.................................................................... ..............................................36
A CHANNEL PROGRAMMABLE "x" CONTROL CHANGE :............................................................................37A CHANNEL PROGRAMMABLE "y" CONTROL CHANGE :............................................................................38B CHANNEL BANK SELECT CC00 & CC32 : ....................................................................................................39
B CHANNEL PROGRAM CHANGE : ..................................................................................................................40B CHANNEL PROGRAMMABLE "x" CONTROL CHANGE : ............................................................................ 41B CHANNEL PROGRAMMABLE "y" CONTROL CHANGE : ............................................................................ 42
PATCH PARAMETERS FLOW CHART: .............................................................................................................43WRITE PATCH MEMORY:..................................................................................................................................44
FACTORY RESET & MIDI DATA DUMP.............................................................................. 45FACTORY RESET:...............................................................................................................................................46DATA MIDI DUMP (sending):..............................................................................................................................47
DATA MIDI DUMP (receiving): ...........................................................................................................................48
FREE MODE.............................................................................................................................. 49MESSAGE SELECTION.......................................................................................................................................49THE POSSIBLE MIDI MESSAGES:.....................................................................................................................50MIDI MESSAGE TRANSMISSION:............................ .........................................................................................52
MIDI CHANNEL/ PATCH BAY SWITCHES .......................................................................................................53
FACTORY SETUP & RANGE.................................................................................................. 54GLOBAL PARAMETERS.....................................................................................................................................54SET PARAMETERS .............................................................................................................................................54PATCH PARAMETERS.......................................................................................................................................54
TECHNICAL SPECIFICATIONS ............................................................................................ 55SPARE PARTS & OPTIONALS ............................................................................................... 56
-
8/18/2019 Proel MS32 Manual
3/57
Proel MS 32 Owner's Manual 3
SPECIFICATIONS Rear Panel I/O & switch :
MIDI In
MIDI Out with Phantom Power
MIDI Thru
Foot Controller 1 In (FC 1 In)
Foot Controller 2 In (FC 2 In
Patch Bay Switch 1 Out (PBS 1 Out)
Patch Bay Switch 2 Out (PBS 2 Out)
Patch Bay Switch 3 Out (PBS 3 Out)
Patch Bay Switch 4 Out (PBS 4 Out)
DC In
16 Switches, 3 Led
Display :
LCD 16 x 1
Mode :
Free
Patch
Set
Memory structure : (1 global, 10 sets, 100 patches)
Global parameter:1. Power On 10 characters name
2. Power On Set and Patch Number
3. RX Basic Midi Channel for Set and Patch recall Program Changes
4. Foot Controller 1 min/max calibrate
5. Foot Controller 2 min/max calibrate
6. Continue switch assign
10 Setseach containing:
1. 10 characters name
2. Song select to be sent (0~127/Off)
3. "A" part Midi Channel (1~16)
4. "B" part Midi Channel (1~16)
5. 10 Patches to be recalled
100 Patches10 for each Set containing 2 parts (A,B) midi data:1. FC 1 assign to CC (0~120 on channel A/B,AB, Off with min and max value)
2. FC 2 assign to CC (0~120 on channel A/B AB, Off with min and max value)
3.
FC1/2 link (On/Off)4. PBS 1-2-3-4 closed or opened (On/Off)
5. "A"- CC 00 (0~127/Off)
6. "A"- CC 32 (0~127/Off)
7. "A"- PC (1~128/Off)
8. "A"- xCC (0~120 at value 0~127/Off)
9. "A"- yCC (0~120 at value 0~127/Off)
10. "B"- CC 00 (0~127/Off)
11. "B"- CC 32 (0~127/Off)
12. "B"- PC (1~128/Off)
13. "B"- xCC (0~120 at value 0~127/Off)
14. "B"- yCC (0~120 at value 0~127/Off
-
8/18/2019 Proel MS32 Manual
4/57
4 Proel MS 32 Owner's Manual
MEMORY STRUCTURE
SET 0
SET 1
SET 9
Set name
Song select
"A" Midi Channel
"B" Midi Channel
10 Patches
"0~127/Off"
PATCH 0
PATCH 1
PATCH 9
"A"-CC 00
"A"-CC 32
"A"-PC
"A"- xCC
"A"- yCC
"SET NAME"
"0~127/Off"
"0~127/Off"
"1~128/Off"
"0~120"
"0~127/Off"
"0~120"
"0~120,A/B,AB
"0~127 (16 values) "
"On/Off"
"On/Off"
SET PARAMETERS
PATCH PARAMETERS
"0~9,0~9"
"1~16/Off"
"POWER-ON NAME"
GLOBAL PARAMETERS
"1~16"
"1~16"
"B"-CC 00
"B"-CC 32
"B"-PC
"B"- xCC
"B"- yCC
FC1
FC2
PBS1
PBS2
PBS3 PBS4
"127~0 (16 values)"
"0~120,A/B,AB
"0~127 (16 values) "
"127~0 (16 values)"
"1~128/Off"
"0~120"
"0~127/Off"
"0~120"
"0~127/Off"
"0~127/Off"
"On/Off"
"On/Off"
"min/max calibrate"
"min/max calibrate"
"Cnt,PBS,Cnt+PBS"
"on/off"
"0~127/Off" "0~127/Off"
-
8/18/2019 Proel MS32 Manual
5/57
Proel MS 32 Owner's Manual 5
MS 32 FRONT AND REAR VIEW
D C I N 9 V
F C 2
F C 1
P B4 P B 3 P B2 P B1
T HR U
O UT
I N
L C D C O NT RA S T
MI DI
-
8/18/2019 Proel MS32 Manual
6/57
6 Proel MS 32 Owner's Manual
POWER ON
When switched on the MS32 displays 3 subsequent screen shots before displaying the MASTER
screen shot;
first screen shot:
second screen shot:
third screen shot:
MASTER screen shot in the Patch mode:
PROEL MIDISender
MS-32 User Name
00 Basic Ch = 16
0 *FACTORY0* >0
-
8/18/2019 Proel MS32 Manual
7/57
Proel MS 32 Owner's Manual 7
GLOBAL PARAMETERS
- 10 characters name,
- SET and PATCH numbers displayed at power on
- the midi Basic channel and
- the calibrations for the Foot Controllers 1 and 2
- the assignment of the CONTINUE switch can be programmed as follows:
Power on the MS32 by keeping the "SELECT/CHANNEL" switch pressed; as soon as the stored
name is displayed, release the "SELECT/CHANNEL" switch;
POWER-ON NAME :
The "10 " and "10 " switches (
)
allow you to choose the character to beinserted.
(Keeping the switch pressed the characters
will shift automatically).
Use the " 5" and "6 " switches (
)
***User Name ***
Character Cursor
***User Name ***
-
8/18/2019 Proel MS32 Manual
8/57
8 Proel MS 32 Owner's Manual
Press and release:
- the "CCXXX/CONTINUE" switch (
) to confirm the data and pass to thedisplay/modification of the following "GLOBAL" parameter or
- the "SELECT/CHANNEL" switch (
) to confirm the data and exit from "GLOBAL" parameter
programming.
POWER-ON SET & PATCH RECALL :
Press the "10 " and "10 " switches (
)to choose the value (from 0 to 9) to be
inserted. (Keeping the switch pressed the
characters will shift automatically).
Use the " 5" and "6 " switches (
)
to move the cursor from SET to PATCH.
SET 0 & PATCH 0
SET 0 & PATCH 0
Value Cursor
-
8/18/2019 Proel MS32 Manual
9/57
Proel MS 32 Owner's Manual 9
Press and release:
- the "CCXXX/CONTINUE" switch (
) to confirm the data and pass to thedisplay/modification of the following "GLOBAL" parameter or
- the "SELECT/CHANNEL" switch (
) to confirm the data and exit from "GLOBAL" parameter
programming.
BASIC RX MIDI CHANNEL :
Press the "10
" and "10
" switches (
)to choose the value (from 1 to 16 or AL =
Omni On) to be inserted and the On/Off
condition. (Keeping the switch pressed the
characters will shift automatically).
Use the " 5" and "6 " switches (
)
to move the cursor from channel number to
On/Off
Basic RxCh 16 On
Basic RxCh 16 On
Value Cursor
-
8/18/2019 Proel MS32 Manual
10/57
10 Proel MS 32 Owner's Manual
Press and release:
- the "CCXXX/CONTINUE" switch (
) to confirm the data and pass to thedisplay/modification of the following "GLOBAL" parameter or
- the "SELECT/CHANNEL" switch (
) to confirm the data and exit from "GLOBAL" parameter
programming.
FOOT CONTROLLER 1 CALIBRATION :
FC1 mn -- Mx --
Position the Foot Pedal inserted in the FC1
socket at minimum value and press the
START/STOP switch;
Position the Foot Pedal at maximum valueand press the START/STOP switch (
).
OK is displayed twice on the screen.
FC1 mn Ok Mx Ok
-
8/18/2019 Proel MS32 Manual
11/57
Proel MS 32 Owner's Manual 11
Press and release:
- the "CCXXX/CONTINUE" switch (
) to confirm the data and pass to thedisplay/modification of the following "GLOBAL" parameter or
- the "SELECT/CHANNEL" switch (
) to confirm the data and exit from "GLOBAL" parameter
programming.
FOOT CONTROLLER 2 CALIBRATION :
FC2 mn -- Mx --
Position the Foot Pedal inserted in the FC2
socket at minimum value and press theSTART/STOP switch;
Position the Foot Pedal at maximum value
and press the START/STOP (
) switch.
OK is displayed twice on the screen.
FC2 mn Ok Mx Ok
-
8/18/2019 Proel MS32 Manual
12/57
12 Proel MS 32 Owner's Manual
Press and release:
- the "CCXXX/CONTINUE" switch (
) to confirm the data and pass to thedisplay/modification of the following "GLOBAL" parameter or
- the "SELECT/CHANNEL" switch (
) to confirm the data and exit from "GLOBAL" parameter
programming.
CONTINUE SWITCH ASSIGNMENT:
Continue=Cnt
Press the "10 " and "10 " switches ( )to select the Cnt (Continue), PBS (Patch
Bay Switches) or Cnt+PBS options.
Continue=Cnt
Value
-
8/18/2019 Proel MS32 Manual
13/57
Proel MS 32 Owner's Manual 13
GLOBAL PARAMETERS FLOW CHART :
"SELECT/CHANNEL" Switch
"CC XX/CONTINUE" Switch
POWER-ONNAME
POWER-ON
SET & PATCHRECALL
BASIC
RX MIDICHANNEL
FC 1CALIBRATION
FC 2CALIBRATION
EXIT
GLOBALPARAMETER
CONTINUESWITCH ASSIGN
-
8/18/2019 Proel MS32 Manual
14/57
14 Proel MS 32 Owner's Manual
WRITE GLOBAL PARAMETER:
Press and release the "SELECT/CHANNEL" switch (
) to confirm the data and exit from
"GLOBAL" parameter programming; the display will show the following message:
When using the WRITE switch the display will show the following message:
and will go back to the PATCH MASTER screen shot after some seconds:
WriteGlobal? W/S
Keep the WRITE/MODE switch (
)
pressed to store the GLOBAL parameters.
Press the START/STOP switch (
) toexit without storing the GLOBAL
parameters; the data of the previous
parameters will be lost.
WriteGlobal? W/S
Write Complete !
0 *FACTORY0* >0
-
8/18/2019 Proel MS32 Manual
15/57
Proel MS 32 Owner's Manual 15
MODE
When turned on, the MS32 is set in the PATCH mode.
Press and release the MODE/WRITE switch (
) to select one of the three operating modes of the
foot pedal as shown in the corresponding LEDs placed beside the display:
-
PATCH- FREE
- SET
Keep the MODE/WRITE switch pressed for some seconds to enter the functions WRITE SET or
WRITE PATCH.
-
8/18/2019 Proel MS32 Manual
16/57
16 Proel MS 32 Owner's Manual
SET MODE
In the SET mode it is possible to:
- recall the 10 SETS stored in the pedalboard using the switches from 0 to 9
- recall the 10 SETS stored in the pedalboard using the switches " "
- activate START/STOP and CONTINUE functions
- edit the SET parameters using the SELECT/CHANNEL" switch
SET SELECTION (0~9):
The pedalboard is in the SET mode when the SET LED is on, the cursor is under the SET Number
and the arrow points the SET Number.
When pressing one of the switches from 0 to 9 or one of the switches " ", the left side of the
display shows the SET number recalled and the 10 characters name associated to it.
All the set parameters are recalled :-
Song from 0 to 127/Off (midi message F3 00~7F)
- “A” part Midi Channel setting (from 1 to 16)
- “B” part Midi Channel setting (from 1 to 16)
- the stored PATCH of the new recalled SET is automatically selected
- all the recalled Set and Patch parameters are transmitted via Midi
Example:
press the switch no. 6 once or the " " switch six times, the display will show:
Note: The pedalboard allows you to recall alternatively two different sets using only one switch;
to recall alternatively the sets no. 3 and 7 press:
- the switch no. 3
- the switch no. 7
The pedalboard will now recall alternatively the sets no. 3 and 7 by pressing only switch no 7.
6
-
8/18/2019 Proel MS32 Manual
17/57
Proel MS 32 Owner's Manual 17
START/STOP AND CONTINUE FUNCTIONS:
When the switch START/STOP is pressed once, the START "FA" Midi message is sent to a
computer or a module sequencer connected via Midi to start a song; the display will show an "s".
If the switch START/STOP is pressed again, the STOP "FC" Midi message is sent to the equipment
connected to stop the song and the "s" is no longer displayed.
Pressing the "CONTINUE" switch while the pedalboard is in its "STOP" condition, the
CONTINUE "FB" Midi message is sent to play again the song from the previous stop position; the
display shows once again an "s".
Note: The CONTINUE function is linked to the Global "Continue switch assign" parameter.
To operate as CONTINUE control, the "Continue switch assign" parameter must beset in CNT or in PBS+CNT (cfr. page 11)
The CONTINUE switch can also operate only as PATCH BAY (PBS) selector if the
Global "Continue switch assign" parameter is set in PBS.The "s" symbol is no longer displayed when the CONTINUE switch is kept pressed.
(cfr. page 33/34)
NOTE:
Remember to set in LOCAL (INTERNAL CLOCK, REMOTE CONTROL, etc.) all theequipments (computer, module sequencer, etc.) connected via Midi to the MS 32 if you want to
control the START/STOP/CONTINUE functions from the pedalboard (note that no MIDI CLOCK signal is sent via midi from the MS-32).
0
-
8/18/2019 Proel MS32 Manual
18/57
18 Proel MS 32 Owner's Manual
EDIT SET PARAMETERS
When the pedalboard is in the SET mode press the "SELECT/CHANNEL" switch to edit theparameters of the selected "SET".
The display shows:
Press and release:
-
the "CCXXX/CONTINUE" switch (
) to confirm the data and pass to thedisplay/modification of the first "SET" parameter or
- the "SELECT/CHANNEL" switch (
) to exit from "SET" parameter programming.
EDIT
Edit S continue?
Edit S continue?
Name: *FACTORY0*
-
8/18/2019 Proel MS32 Manual
19/57
Proel MS 32 Owner's Manual 19
SET NAME :
Press and release:
- the "CCXXX/CONTINUE" switch (
) to confirm the data and pass to the
display/modification of the following "SET" parameter or
- the "SELECT/CHANNEL" switch (
) to confirm the data and exit from "SET" parameter
programming.
Press the "10 " and "10 " switches (
)
to select the character to be inserted.(Keeping the switch pressed the characters
will shift automatically).
Use the " 5" and "6 " switches (
)
to move the cursor.
Name: *FACTORY0*
Value Cursor
Song Sel: 0 Of
-
8/18/2019 Proel MS32 Manual
20/57
20 Proel MS 32 Owner's Manual
SONG SELECT :
Press and release:
- the "CCXXX/CONTINUE" switch (
) to confirm the data and pass to the
display/modification of the following "SET" parameter or- the "SELECT/CHANNEL" switch (
) to confirm the data and exit from "SET" parameter
programming.
Press the "10 " e "10 " switches (
) tochoose the value from 0 to 127 and On/Of
to be inserted.(Keeping the switch pressed the characters
will shift automatically).
Press the " 5" and "6 " switches (
)
to move the cursor from Song number to
On/Off
Song Sel: 0 Of
Value Cursor
A PartMIDI Ch 1
-
8/18/2019 Proel MS32 Manual
21/57
Proel MS 32 Owner's Manual 21
"A" PART TX MIDI CHANNEL :
Press and release:
- the "CCXXX/CONTINUE" switch (
) to confirm the data and pass to the
display/modification of the following "SET" parameter or- the "SELECT/CHANNEL" switch (
) to confirm the data and exit from "SET" parameter
programming.
Press the "10 " and "10 " switches (
)
to select a value from 1 to 16.(Keeping the switch pressed the characters
will shift automatically).
A PartMIDI Ch 1
Value
B PartMIDI Ch 2
-
8/18/2019 Proel MS32 Manual
22/57
22 Proel MS 32 Owner's Manual
"B" PART TX MIDI CHANNEL :
Press and release:
- the "CCXXX/CONTINUE" switch (
) to confirm the data and go back to the
display/modification of the first "SET" parameter or- the "SELECT/CHANNEL" switch (
) to confirm the data and exit from "SET" parameter
programming.
Press the "10 " and "10 " switches ( )
to select a value from 1 to 16.(Keeping the switch pressed the characters
will shift automatically).
B PartMIDI Ch 2
Value
Name: *FACTORY0*
-
8/18/2019 Proel MS32 Manual
23/57
Proel MS 32 Owner's Manual 23
SET PARAMETERS FLOW CHART:
SETNAME
SONGSELECT
"A" PART
TX MIDICHANNEL
"B" PART
TX MIDICHANNEL
EXIT
SETPARAMETER
"SELECT/CHANNEL" switch
"CC XXX/CONTINUE" switch
-
8/18/2019 Proel MS32 Manual
24/57
24 Proel MS 32 Owner's Manual
WRITE SET MEMORY:
When keeping the " MODE/WRITE" switch (
) pressed for some seconds
or
in Edit mode : pressing and releasing the "SELECT/CHANNEL" switch (
) to confirm the
data and exit from "SET" parameters programming
the following message will be displayed:
When using the WRITE switch, the display will show the following message:
and will go back to the SET MASTER screen shot after some seconds:
Press the "10 " and "10 " switches (
)
to select a SET from 0 to 9 where to store
the inserted parameters. (Keeping the
switch pressed the characters will shift
automatically).
Keeping the WRITE/MODE switch (
)
pressed the displayed SET is stored.
Press the START/STOP switch (
) to
exit without saving the SET. All the data
of the previously modified parameters are
lost.
WrteSet 0 ? W/S
WrteSet 0 ? W/S
Exit (no write)WriteSet Number
Write Complete !
-
8/18/2019 Proel MS32 Manual
25/57
Proel MS 32 Owner's Manual 25
PATCH MODE
In the PATCH mode it is possible to:
- recall the 10 PATCHES of the current SET stored using the switches from 0 to 9
- recall the 10 SETS stored using the " " switches
- activate the START/STOP and the CONTINUE functions
- edit the PATCH parameters using the "SELECT/CHANNEL" switch
0~9 PATCH SELECTION:
When the PATCH LED is on, the cursor is under the PATCH number and an arrow points the
PATCH number, the MS32 is in its PATCH selection mode.
Pressing one of the switches from 0 to 9 the display will show, on the right side of the screen, the
PATCH number of the current SET.
All the patch parameters are recalled and transmitted via Midi:
Example:
when the switch no. 3 is pressed, the display will show:
0 *FACTORY0* >3
SET Number SET Name PATCH Number
EDIT 0~9 PATCH SELECTION START/STOP
0~9 SET SELECTION
START/STOP
-
8/18/2019 Proel MS32 Manual
26/57
26 Proel MS 32 Owner's Manual
If the " " or " " switches are pressed it is possible to select a different patch SET.
Example: the currently recalled patch no. 3 belongs to the set no. 0.
The pedalboard has 10 Sets, numbered from 0 to 9 and each set includes 10
patches.
It is therefore possible to recall the patches no. 0-3, 1-3, 2-3…9-3, each of themwith different parameters.
Note: The MS-32 allows you to recall alternatively two patches by using only one switch; forexample, to recall alternatively the patches no. 3 e 7 press:
- switch no. 3
- switch no. 7
The pedalboard will now recall alternatively the two patches, 3 and 7, when pressing only
the switch no. 7.
START/STOP AND CONTINUE FUNCTIONS:
If the switch START/STOP is pressed once, the START "FA" Midi message is sent to a computer
or a module sequencer connected via Midi to start a song; the display will show an "s".
When the switch START/STOP is pressed again, the STOP "FC" Midi message is sent to the
equipment connected to stop the song; the "s" is no longer displayed.
Pressing the "CONTINUE" switch while the pedalboard is in its "STOP" condition, the
CONTINUE "FB" Midi message is sent to play the song from the previous stop position; the
display shows once again an "s".
Note: The CONTINUE function is linked to the Global "Continue switch assign" parameter.
To operate as CONTINUE control, the "Continue switch assign" parameter must be
set in CNT or in PBS+CNT (cfr. page 11)
The CONTINUE switch can also operate only as PATCH BAY (PBS) selector if the
Global "Continue switch assign" parameter is set in PBS.The "s" symbol is no longer displayed when the CONTINUE switch is kept pressed.
(cfr. page 33/34)
NOTE:
Remember to set in LOCAL (INTERNAL CLOCK, REMOTE CONTROL, etc.) all the
equipments (computer,module sequencer, etc.) connected via Midi to the MS 32 if you want to
control the START/STOP/CONTINUE functions from the pedalboard (note that no MIDI
CLOCK signal is sent via midi from the MS-32).
0 *FACTORY0* s>3
START or CONTINUE selected
-
8/18/2019 Proel MS32 Manual
27/57
Proel MS 32 Owner's Manual 27
EDIT PATCH PARAMETERS:
When the pedalboard is in the PATCH mode, press the "SELECT/CHANNEL" switch to edit the
parameters of the selected PATCH.
The display will show:
Press and release:
- the "CCXXX/CONTINUE" switch (
) to display or modify the first “PATCH” parameter or
- the "SELECT/CHANNEL" switch (
) to exit from “PATCH” parameter programming.
EDIT
Edit P continue?
Edit P continue?
FC1 to 7 AB On
-
8/18/2019 Proel MS32 Manual
28/57
28 Proel MS 32 Owner's Manual
FC1 ASSIGN :
Press and release:
- the "CCXXX/CONTINUE" switch (
) to confirm the data and display/modify the following
“PATCH” parameter or- the "SELECT/CHANNEL" switch (
) to confirm the data and exit from “PATCH” parameter
programming.
FC1 mn 0 Mx127
Press the "10 " and "10 " switches (
)
to select a Control Change value, from 0 to
120, the A/B/AB channel, and the On/Off
conditions.(Keeping the switch pressed the characterswill shift automatically).
Use the " 5" and "6 " switches (
)
to move the cursor back and forward.
FC1 to 7 AB On
Value Cursor
-
8/18/2019 Proel MS32 Manual
29/57
Proel MS 32 Owner's Manual 29
FC1 RANGE :
Press and release:- the "CCXXX/CONTINUE" switch (
) to confirm the data and display/modify the following
“PATCH” parameter or- the "SELECT/CHANNEL" switch (
) to confirm the data and exit from “PATCH” parameter
programming.
FC2 to 11 AB On
Use the "10 " and "10 " switches (
)
to select a value from 0 to 127 to be
inserted as minimum and maximum pedalvalues.(Keeping the switch pressed the characters
will shift automatically).
Use the " 5" and "6 " switches (
)
to move the cursor back and forward.
FC1 mn 0 Mx127
Value Cursor
-
8/18/2019 Proel MS32 Manual
30/57
30 Proel MS 32 Owner's Manual
FC2 ASSIGN :
Press and release:
- the "CCXXX/CONTINUE" switch (
) to confirm the data and display/modify the following“PATCH” parameter or
- the "SELECT/CHANNEL" switch (
) to confirm the data and exit from “PATCH” parameterprogramming.
FC2 mn 0 Mx127
FC2 to 11 AB On
Value Cursor
Press the "10 " and "10 " switches (
)
to select a Control Change value from 0 to
120, the A/B/AB channel, and the On/Off
position.(Keeping the switch pressed the characterswill shift automatically).
Use the " 5" and "6 " switches (
)
to move the cursor back and forward.
-
8/18/2019 Proel MS32 Manual
31/57
Proel MS 32 Owner's Manual 31
FC2 RANGE :
Press and release:- the "CCXXX/CONTINUE" switch (
) to confirm the data and display/modify the following
“PATCH” parameter or- the "SELECT/CHANNEL" switch (
) to confirm the data and exit from “PATCH” parameter
programming.
FC1/2 Link Of
FC2 mn 0 Mx127
Value Cursor
Press the "10 " and "10 " (
) to select
a value from 0 to 127 to be inserted as
minimum and maximum pedal values.(Keeping the switch pressed the characterswill shift automatically).
Use the " 5" and "6 " switches (
)
to move the cursor back and forward.
-
8/18/2019 Proel MS32 Manual
32/57
32 Proel MS 32 Owner's Manual
FC 1/2 LINK :
Press and release:- the "CCXXX/CONTINUE" switch (
) to confirm the data and display/modify the following
“PATCH” parameter or
- the "SELECT/CHANNEL" switch (
) to confirm the data and exit from “PATCH” parameter
programming.
Press the "10 " and "10 " switches (
)
to select the On/Off value of the Link
between the Foot Controllers 1 and 2.
When the Link is On each Foot Controller
transmits the parameters of both.
FC1/2 Link Of
Value
PBS1 Of PBS2 Of
-
8/18/2019 Proel MS32 Manual
33/57
Proel MS 32 Owner's Manual 33
PATCH BAY SWITCH 1-2 :
Note: The Patch bays stored in the ON condition can be rapidly activated and deactivated
when out of the EDIT mode by pressing the Continue switch.
The Patch Bay Switch function is linked to the Global "Continue switch assign"
parameter.
To operate as Patch Bay Switch (PBS) control, the "Continue switch assign"parameter must be set in PBS or in PBS+CNT (cfr. page 11)
Press and release:
-
the "CCXXX/CONTINUE" switch (
) to confirm the data and display/modify the following"PATCH" parameter or- the "SELECT/CHANNEL" switch (
) to confirm the data and exit from "PATCH" parameter
programming.
PBS3 Of PBS4 Of
PBS1 Of PBS2 Of
Value Cursor
Press the "10 " and "10 " switches (
)to select the On/Off condition to be
inserted for the patch bay switches 1 and 2.
Use the " 5" and "6 " switches (
)
to move the cursor back and forward.
-
8/18/2019 Proel MS32 Manual
34/57
34 Proel MS 32 Owner's Manual
PATCH BAY SWITCH 3-4 :
Note: The Patch bays stored in the On condition can be rapidly activated and deactivated
when out of the EDIT mode by pressing the Continue switch.
The Patch Bay Switch function is linked to the Global "Continue switch assign"
parameter.
To operate as PBS control, the "Continue switch assign" parameter must be set inPBS or in PBS+CNT (cfr. page 11)
Press and release:
-
the "CCXXX/CONTINUE" switch ( ) to confirm the data and display/modify the following"PATCH" parameter or
- the "SELECT/CHANNEL" switch (
) to confirm the data and exit from "PATCH" parameter
programming.
A c0= Of c32= 0f
PBS3 Of PBS4 Of
Value Cursor
Press the "10 " and "10 " switches (
)to choose the On/Off condition to be
inserted for the patch bay switches 3 and 4.
Use the " 5" e "6 " switches (
) to
move the cursor back and forward.
-
8/18/2019 Proel MS32 Manual
35/57
Proel MS 32 Owner's Manual 35
A CHANNEL BANK SELECT CC00 & CC32 :
Press and release:
- the "CCXXX/CONTINUE" switch (
) to confirm the data and display/modify the following"PATCH" parameter or
- the "SELECT/CHANNEL" switch (
) to confirm the data and exit from "PATCH" parameterprogramming.
A PC = Of
A c0= Of c32= 0f
Value Cursor
Press the "10 " and "10 " switches (
)
to select a value from 0 to 27, and the Off condition to be inserted for the A Midi
channel CC00 and CC32.
Use the " 5" and "6 " switches (
)
to move the cursor back and forward.
-
8/18/2019 Proel MS32 Manual
36/57
36 Proel MS 32 Owner's Manual
A CHANNEL PROGRAM CHANGE :
Press and release:
- the "CCXXX/CONTINUE" switch (
) to confirm the data and display/modify the following
"PATCH" parameter or- the "SELECT/CHANNEL" switch (
) to confirm the data and exit from "PATCH" parameter
programming.
A xCC 91 = 40
A PC = Of
Value
Press the "10 " and "10 " switches ( )
to select a value from 1 to 128 and the Off
condition to be inserted for the A channel
program change midi message.
-
8/18/2019 Proel MS32 Manual
37/57
Proel MS 32 Owner's Manual 37
A CHANNEL PROGRAMMABLE "x" CONTROL CHANGE :
Press and release:
- the "CCXXX/CONTINUE" switch (
) to confirm the data and display/modify the following"PATCH" parameter or
- the "SELECT/CHANNEL" switch (
) to confirm the data and exit from "PATCH" parameterprogramming.
A yCC 93 = 0
A xCC 91 = 40
Value Cursor
Press the "10 " and "10 " switches (
)
to select a value from 0 to 120 and 0 to
127, in the Off condition, to be inserted,
respectively, as the type and the value of A channel control change.
Use the " 5" and "6 " switches (
)
to move the cursor back and forward.
-
8/18/2019 Proel MS32 Manual
38/57
38 Proel MS 32 Owner's Manual
A CHANNEL PROGRAMMABLE "y" CONTROL CHANGE :
Press and release:
- the "CCXXX/CONTINUE" switch (
) to confirm the data and display/modify the following"PATCH" parameter or
- the "SELECT/CHANNEL" switch (
) to confirm the data and exit from "PATCH" parameterprogramming.
B c0= Of c32= 0f
A yCC 93 = 0
Value Cursor
Press the "10 " and "10 " switches (
)
to select a value from 0 to 120 and 0 to
127, in the Off condition, to be inserted,
respectively, as the type and the value of A channel control change.
Use the " 5" and "6 " switches (
)
to move the cursor back and forward.
-
8/18/2019 Proel MS32 Manual
39/57
Proel MS 32 Owner's Manual 39
B CHANNEL BANK SELECT CC00 & CC32 :
Press and release:
- the "CCXXX/CONTINUE" switch (
) to confirm the data and display/modify the following"PATCH" parameter or
- the "SELECT/CHANNEL" switch (
) to confirm the data and exit from "PATCH" parameterprogramming.
B PC = Of
B c0= Of c32= 0f
Value Cursor
Press the "10 " and "10 " switches (
)
to select a value from 0 to 127 and the Off
condition to be inserted for the B channel
CC00 and CC32.
Use the " 5" and "6 " switches (
)
to move the cursor back and forward.
-
8/18/2019 Proel MS32 Manual
40/57
40 Proel MS 32 Owner's Manual
B CHANNEL PROGRAM CHANGE :
Press and release:
- the "CC XXX/CONTINUE" switch (
) to confirm the data and display/modify the following
"PATCH" parameter or- the "SELECT/CHANNEL" switch (
) to confirm the data and exit from "PATCH" parameter
programming.
B xCC 91 = 40
B PC = Of
Value
Press the "10 " and "10 " switches (
)
to select a value from 1 to 128 and the Off
condition to be inserted for the B channel
program change.
-
8/18/2019 Proel MS32 Manual
41/57
Proel MS 32 Owner's Manual 41
B CHANNEL PROGRAMMABLE "x" CONTROL CHANGE :
Press and release:
- the "CCXXX/CONTINUE" switch (
) to confirm the data and display/modify the following"PATCH" parameter or
- the "SELECT/CHANNEL" switch (
) to confirm the data and exit from "PATCH" parameterprogramming.
B yCC 93 = 0
B xCC 91 = 40
Value Cursor
Press the "10 " and "10 " switches (
)
to select a value from 0 to 120 and 0 to
127, in the Off condition, to be inserted,
respectively, as the type and the value of B channel control change.
Use the " 5" and "6 " switches (
)
to move the cursor back and forward.
-
8/18/2019 Proel MS32 Manual
42/57
42 Proel MS 32 Owner's Manual
B CHANNEL PROGRAMMABLE "y" CONTROL CHANGE :
Press and release:
- the "CCXXX/CONTINUE" switch (
) to confirm the data and go back to thedisplay/modification of the first "PATCH" parameter or
- the "SELECT/CHANNEL" switch (
) to confirm the data and exit from "PATCH" parameterprogramming.
FC1 to 7 AB On
B yCC 93 = 0
Value Cursor
Press the "10 " and "10 " switches (
)
to select a value from 0 to 120 and 0 to
127, in the Off condition, to be inserted,
respectively, as the type and the value of B channel control change.
Use the " 5" and "6 " switches (
)
to move the cursor back and forward.
-
8/18/2019 Proel MS32 Manual
43/57
Proel MS 32 Owner's Manual 43
PATCH PARAMETERS FLOW CHART:
FC 1 ASSIGN
FC 1 RANGE
"SELECT/CHANNEL" Switch
"CC XXX/CONTINUE" Switch
FC 2 ASSIGN
FC 2 RANGE
PBS 1 & PBS 2
PBS 3 & PBS 4
A CC0 & CC32
A Program Change
A xControl Change
A yControl Change
B CC0 & CC32
B Program Change
B xControl Change
B yControl Change
EXIT PATCHPARAMETER
FC 1/2 LINK
-
8/18/2019 Proel MS32 Manual
44/57
44 Proel MS 32 Owner's Manual
WRITE PATCH MEMORY:
When keeping the " MODE/WRITE" switch (
) pressed for some seconds
or
in Edit mode : pressing and releasing the "SELECT/CHANNEL" switch (
) to confirm the
data and exit from "PATCH" parameters programming
the following message will be displayed:
When using the WRITE switch, the display will show:
and after some seconds will go back to the PATCH MASTER screen shot:
Write Complete !
WrtPtch 0-0? W/S
Press the "10 " and "10 " switches (
)
to choose the SET and one of the "0~9"
switches (
) to select a Patch (from 0-0to 9-9) where to store the inserted
parameters.
Keeping the WRITE/MODE switch (
)
pressed, the currently displayed PATCH is
stored.
Press the START/STOP switch (
) to exit
without storing the SET. The data of the
previously modified parameters will be
lost.
Patch Number
WrtPtch 0-0? W/S
Exit (no write)
Write
Set Number
0 *FACTORY0* >0
-
8/18/2019 Proel MS32 Manual
45/57
Proel MS 32 Owner's Manual 45
FACTORY RESET & MIDI DATA DUMP
The MS-32 pedalboard is provided with the following functions:
- FACTORY RESET to restore the original parameters set by the manufacturers.
- MIDI DATA DUMP (transmission) to download the memory parameters via Midi on a
connected Sequencer or Computer.
-
MIDI DATA DUMP (reception) to reload via Midi the memory parameters previously saved in a
connected Sequencer o Computer.
When powered-on through the " MODE/WRITE" switch, the display of the pedalboard shows the
following screen shot; release then the " MODE/WRITE" switch;
WrtPtch 0-0? W/S
Factory Reset
or
Data Midi Dump
Press the "0" or "9" switches (
) to select,
respectively, Factory Reset or Data Midi
Dump functions.
Press the START/STOP switch (
) to
exit from the Factory/Dump screen shot
and go back to the main menu.
Exit
0-Factory 9-Dump
-
8/18/2019 Proel MS32 Manual
46/57
46 Proel MS 32 Owner's Manual
FACTORY RESET:
Pressing and releasing the "0" switch, the display will show:
Press and release:
-
the "CC XXX/CONTINUE" switch (
) to reset the pedalboard with all the Factory parameters;
all the parameters of the GLOBAL, SET and PATCH memories are removed and reset at
"factory" value.- the "START/STOP" switch (
) to exit from the "FACTORY" function.
- If the Continue switch is pressed, the pedalboard will display:
and go back to the main screen shots.
- Press Start/Stop to exit from the "FACTORY" function; the pedalboard will display the main
screen shots.
Reset Continue?
Reset Continue?
Loading Factory!
-
8/18/2019 Proel MS32 Manual
47/57
Proel MS 32 Owner's Manual 47
DATA MIDI DUMP (sending):
Pressing and releasing the "9" switch, the display will show:
Press and release:
- the "CCXXX/CONTINUE" switch ( ) to start dumping the selected data (All, Global, Set, or
Patch) through the Midi Out (downloadable on a Sequencer or Computer)- the "START/STOP" switch (
) to exit from the "DUMP" function.
- If the Continue switch is pressed, the pedalboard will show:
When the data transmission is completed, the display will go back to the main screen shots..
Dump All Cont?
Dump All Cont?
Value
Press the "10 " and "10 " switches (
)to select the data to be inserted: All (all the
data), Glb (only the Global memory), Set
(only the 10 Set memories), Ptc (only the
100 Patch memories)
Dump All Cont?
Sending Dump.. !
-
8/18/2019 Proel MS32 Manual
48/57
48 Proel MS 32 Owner's Manual
DATA MIDI DUMP (receiving):
If a Data Midi Dump exclusive system is received (the same system generated by the pedalboard
when the Data Midi Dump is transmitting) via Sequencer or Computer, the MS-32 enters the Data
Midi Dump mode and will display the following screen shot:
alternating with the display of the different memories received.
- The pedalboard memories are thus loaded with the received Midi data, previously saved throughthe DATA MIDI DUMP (transmission) procedure.
Note : It is important not to accelerate the DATA DUMP procedure as the pedalboard needs
time to edit the data in the Flash memory.
If there is a reception problem or an error in the data loading, it is advisable to slow
down the dump procedure in the connected computer or sequencer.
- If the pedalboard is switched off during this procedure, incomplete data might be received.
When the data receiving is completed the pedalboard stops on the last memory received ordisplays:
This means the data reception was not successfully completed; it is necessary to switch thepedalboard off and activate the Factory Reset functioned described at pages 45/46.Retry the loading procedure controlling the dump speed and slowing it down if necessary.
Receiving Dump.!
Rx Dump Error..!
-
8/18/2019 Proel MS32 Manual
49/57
-
8/18/2019 Proel MS32 Manual
50/57
50 Proel MS 32 Owner's Manual
THE POSSIBLE MIDI MESSAGES:
CCXX switch
CC00 switch
CC32 switch
PC 0~127 switch
PC 1~128 switch
CC 07 switch
CC 10 switch
CC YY switch
CC 11 switch
CC 16 switch
Ch = 1 CC 16= 0
Ch = 1 CC 11= 0
CC 0 Continue? Ch = 1 CC 0= 0
Ch = 1 CC 10= 0
Ch = 1 CC 07= 0
Ch = 1 PC128= 0
Ch = 1 PC127= 0
Ch = 1 CC 32= 0
Ch = 1 CC 00= 0
CC 0 Continue? Ch = 1 CC 0= 0
-
8/18/2019 Proel MS32 Manual
51/57
Proel MS 32 Owner's Manual 51
CC 91 switch
CC 93 switch
CC 94 switch
SONG switch
Ch = 1 Song = 0
Ch = 1 CC 94= 0
Ch = 1 CC 93= 0
Ch = 1 CC 91= 0
-
8/18/2019 Proel MS32 Manual
52/57
52 Proel MS 32 Owner's Manual
MIDI MESSAGE TRANSMISSION:
When CC XXX and CC YYY are selected the display shows:
After selecting the type of Control Change to be sent using the " ", " " and "0~9" switches,
press the Continue switch (in this case "Start / stop" and "Continue" do not operate), the display
shows:
It is now possible to select the value to be sent through the above-described procedure.
NOTE : In the FREE mode the Foot Controllers 1 and 2 send the values of the selected midi
messages.
CC 0 Continue?
Ch = 1 CC 0= 0
Ch= 1 CC 07= 0Press the "10 " and "10 " switches (
)
to select the first and the second digit of
the value to be sent; use the switches from"0" to "9" (
) to select the unit of thethree-digit number and confirm the Midi
message transmission.
Press the Start/Stop and Continue switches
to activate the Start(FA), Stop (FC) e
continue (FB) messages. (cfr. page 22)
Value Value START/STOPCONTINUE
-
8/18/2019 Proel MS32 Manual
53/57
Proel MS 32 Owner's Manual 53
MIDI CHANNEL/ PATCH BAY SWITCHES
In the "FREE" mode it is possible to select the Midi channel where to send the messages and enterthe PATCH BAY SWITCHES section to activate the 4 On/Off:
.
MIDI CHANNEL/PATCH BAY SELECTION
Keep the "SELECT/CHANNEL" switch pressed for some seconds to select the midi channel and
the patch Bay
The display shows:
Press the " " and " " switches to select the Midi channel.
Press the "SELECT/CHANNEL" switch again to exit and go back to the FREE mode.
Press the "Continue" switch to display the PATCH BAY SWITCHES:
Press the switches from 1 to 4 to select alternatively the On or Off condition for the correspondingPATCH BAY switches.
Press the "SELECT/CHANNEL" switch to exit and go back to the FREE mode.
1on 2on 3on 4on
Ch= 1 Continue ?
Ch= 1 Continue ?
Channel
-
8/18/2019 Proel MS32 Manual
54/57
54 Proel MS 32 Owner's Manual
FACTORY SETUP & RANGE
GLOBAL PARAMETERS
FACTORY VALUE RANGE
"POWER-ON NAME" User Name ASCII
"0~9,0~9" 0-0 0~9-0~9
"1~16/Off" 16 On 1~16 On/Of "min/max calibrate" 30-97 0~126-1~127
"min/max calibrate" 30-97 0~126-1~127
SET PARAMETERS
FACTORY VALUE RANGE "SET NAME" FACTORY ASCII
"1~16" 1 1~16
"1~16" 2 1~16
"0~127/Off" 0 Of 0~127 On/Of
PATCH PARAMETERS
FACTORY VALUE RANGE "0~120,A/B,AB Of" 07 AB On 0~120 A/B/AB On/Of
"0~127 (16 values) " 00,8,16,24,32,40,48,
56,64,72,80,88,96,104,112,120,127
"127~0 (16 values)" 1270,8,16,24,32,40,48,
56,64,72,80,88,96,104,112,120,127
"0~120,A/B,AB Of" 11 AB On 0~120 A/B/AB On/Of
"0~127 (16 values) " 00,8,16,24,32,40,48,
56,64,72,80,88,96,104,112,120,127
"127~0 (16 values)" 1270,8,16,24,32,40,48,
56,64,72,80,88,96,104,112,120,127
"On/Off" Of On/Of
"On/Off Of On/Of
"On/Off" Of On/Of
"On/Off" Of On/Of
"0~127/Off" 0 On 0~127 On/Of
"0~127/Off" 0 On 0~127 On/Of
"1~128/Off" 1 On 1~128 On/Of
"0~120" 91 0~120 On/Of
"0~127/Off" 40 Of 0~127 On/Of
"0~120" 93 0~120 On/Of
"0~127/Off" 0 Of 0~127 On/Of
"0~127/Off" 0 On 0~127 On/Of
"0~127/Off" 0 On 0~127 On/Of
"1~128/Off"v 1 On 1~128 On/Of
"0~120" 91 0~120 On/Of
"0~127/Off" 40 Of 0~127 On/Of
"0~120" 93 0~120 On/Of
"0~127/Off" 0 Of 0~127 On/Of
-
8/18/2019 Proel MS32 Manual
55/57
Proel MS 32 Owner's Manual 55
TECHNICAL SPECIFICATIONS
MIDI System Exclusive ID Number: 00H2037H
RX MIDI CHANNEL: 1, 2, 3, …, 16, OMNI
TX MIDI CHANNEL: CHANNEL A: 1, 2, 3, …, 16CHANNEL B: 1, 2, 3, …, 16
MIDI MESSAGGES: cc00, cc32, PC, cc07, cc10, cc16, cc91,
cc93, cc94, Start (FA), Stop (FC),
Continue (FB), Song Select (F3), XXcc,
YYcc
PEDALBOARD SWITCHES
FUNCTIONS: ccXX/Continue, 10 /cc00, 0/cc32,1/pc0-127, 2/pc1-128, 3/cc07, 4/cc10,
ccYY/Start-Stop, Select/Channel,
10 /cc11, 5/cc16, 6/cc91, 7/cc93,
8/cc94, 9/Song, Mode/Write
DISPLAY: LCD with contrast control 16 character xuna line. Dim. 6.0 x 12.72 (W x H) mm.
POWER: DC IN supply 12/9V cc 750mA.
DC IN with Phantom Power through the MIDI
IN
MIDI: 1 Midi OUT with Phantom Power – 7 PIN/DIN1 Midi IN – 5 PIN/DIN
1 Midi THRU – 5 PIN/DIN
LIMITATIONS: The MS-32 is limited only to the
transmission of the messages listed on
page 3 of the owner’s manual. Proel
S.p.A. is not responsible for a different
use.
This product responds to the 83/33 E.C. directives concerning the elettro-magnetical compatibility (EMC)
-
8/18/2019 Proel MS32 Manual
56/57
56 Proel MS 32 Owner's Manual
SPARE PARTS & OPTIONALS
SPARE PARTS
PROEL/DISPLAY: Cod. 91LCDM32
PROEL/DISPLAY LABEL: Cod. 92ETCM32
PROEL/SWITCHS LABELS: Cod. 92ETTM32
PROEL/MIDI 5 PIN SOCKET: Cod. 91PRD5PL
PROEL/MIDI 7 PIN SOCKET: Cod. 91PRD7PL
PROEL/JACK SOCKET: Cod. P385
PROEL/DC IN SOCKET: Cod. PA38/25
PROEL/SWITCH: Cod. 93TSTCHP
PROEL/POWER SUPPLY: Cod. PPSM16
OPTIONALS
PROEL/DIN 7 PIN CABLE: Cod. RLD700
PROEL/DIN 5 PIN CABLE: Cod. SH120
PROEL/FOOT CONTROLLER: Cod. PVP16L
PROEL/PATCH BAY MONO CABLE: Cod. ROAD100LU5
PROEL/OWNER’S MANUAL: Cod. 92MNIM32
PROEL/HARD CASE FOR MS32: Cod. CPMS32
-
8/18/2019 Proel MS32 Manual
57/57
PROEL S.p.A.Zona Artigianale64027 Sant’Omero (TE) – ItalyTel: +39 0861 81241Fax: +39 0861 887862Proel web site: www.proelgroup.comE-mail: [email protected]
Copyright © 1999 PROEL S.p.A.Manufactured and printed in Italy