product maintenance handbook - micro elecmicroelec.co.uk/assets/technical...
TRANSCRIPT
330.PROD.GB.4 : 330.PROD.FPAGE.NONE.NONE.GB.4 Black i
23077 G4 142804044
CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®
CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®
CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®
CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow®CashFlow
The
330REFERENCE SERIES
ACCEPTOR
PRODUCT MAINTENANCEHANDBOOK
®
®
330.PROD.GB.4 : 330.PROD.FPAGE.NONE.NONE.GB.4 Black ii
ii ©, Mars, Inc., 1995.
CashFlow 330 acceptor Product Maintenance Handbook
Published by :
Mars Electronics International
Eskdale Road
Winnersh Triangle
Wokingham, Berkshire RG11 5AQ
United Kingdom
For information on translations and Distributors in your country, please write to the TechnicalCommunications Manager at the above address.
CashFlow 330 acceptor Product Maintenance Handbook
©, Mars, Inc., 1995. All rights reserved.
Except as permitted under the relevant local legislation, no part of this publication may becopied, photocopied, reproduced, transmitted, transcribed, or distributed in any form or by anymeans, or stored in a database or retrieval system, or translated into any language (natural orcomputer), or reduced to any electronic medium or machine readable form, except in anymanner specifically described in the documentation, without the prior written permission ofMars Electronics International.
Mars , CashFlow and the Mars Electronics International device are registered trademarks.
©, Mars, Inc., 1995.
Mars Electronics reserves the right to change the product or the product specifications at anytime. While every effort has been made to ensure that the information in this publication isaccurate, Mars Electronics disclaims any liability for any direct or indirect losses (howsoevercaused) arising out of use or reliance on this information.
This document does not necessarily imply product availability.
Part Number : 142804044
This Edition ( February 1995) Printed in the United Kingdom.
330.PROD.GB.4 : 330.PROD.GB.4.TOC Black iii
©, Mars, Inc., 1995. iii
CashFlow 330 acceptor Product Maintenance Handbook
TABLE OF CONTENTS
SAFETY AND EMC ...................................................................1
OVERVIEW .................................................................................2
INSTALLATION ..........................................................................3
MINI AND MIDI FRONT PLATES ......................................... 3MAXI FRONT PLATE ...........................................................4
CHANNEL MOUNTED .........................................................54" CHANNEL INSTALLATION ..................................... 55" CHANNEL MOUNTING........................................... 7
INITIALISING ..............................................................................8
CONFIGURATION .....................................................................9FACTORY CONFIGURATION .............................................. 9
Specific Coinsets ................................................ 9FIELD CONFIGURATION...................................................10
VIA MAN MACHINE INTERFACE (MMI) ................... 10To Inhibit a Coin ............................................... 11To Enable a Coin.............................................. 11
VIA MARS ROUTE ALPHA 250 TERMINAL........... 12Key Functions...................................................13Other Facilities Of The Terminal....................... 13Auto Repeating Keys........................................ 13Double Click Hotkeying..................................... 14Using The Terminal .......................................... 14
CLEANING THE ACCEPTOR .............................................. 19
FAULT-FINDING ......................................................................20
ELECTRICAL INTERFACES ................................................ 21
HOST INTELLIGENT INTERFACE (HI2) ........................... 21Electrical Specifications.................................... 21
APPLICATIONS SUPPORT ...............................................24
330.PROD.GB.4 : 330.PROD.GB.4.TOC Black iv
iv ©, Mars, Inc., 1995.
CashFlow 330 acceptor Product Maintenance Handbook
SUPPORT TOOLS ....................................................25
MACHINE INTERFACE PCB’s............................................. 26
COMPATIBILITY.................................................................26STANDARD VERSIONS 112 and 124, (0V COMMON12V & 24V) ................................................................27
PCB Connectors - versions 112 and 124 ......... 27Electrical Interfaces - versions 112 and 124..... 29
STANDARD VERSIONS 212 and 312, (0V COMMON12V) ...........................................................................31
PCB Connectors - version Standard 212.......... 31Electrical Interfaces .......................................... 33
DUAL POLARITY.......................................................35PCB Connector - Dual Polarity ......................... 36Electrical Specifications.................................... 36
REPLACING MODULES........................................................39REMOVING THE ACCEPTOR FROM TOP ENTRYADAPTOR..................................................................39REPLACING THE BACK COVER ............................. 40REMOVING THE ACCEPT GATE............................. 41CHANGING THE INTERFACE PCB.......................... 43
ACCESSORIES AND SPARES............................................ 45FRONT PLATES ........................................................45ADAPTOR & CHANNEL ............................................ 45BACK COVERS.........................................................46ACCEPT GATE MODULES ....................................... 47
CASHFLOW MODULES COMPATIBILITY ..................... 48
COMPATIBILITY with EARLIER PRODUCTS ................. 49
MARS ELECTRONICS INTERNATIONAL OFFICES ..... 50
MEI DISTRIBUTORS ..............................................................51
330.PROD.GB.4 : GEN.GEN.SAF_INST.NONE.NONE.GB.5 Black 1
©, Mars, Inc., 1995. 1
CashFlow 330 acceptor Product Maintenance Handbook
SAFETY AND EMC
International & National StandardsConformanceWhen installed and operated according to theinstructions for the particular unit, CashFlow® 330products are designed to meet the applicableSafety and Electro Magnetic Compatibilitystandards for any country in which they are used.
Maximum Operating VoltagesDo not apply more than the indicated voltage.
Dangerous EnvironmentsDo not operate in the presence of flammablegases, fumes or water.
Disposal of ProductDo not dispose of this product by incineration.
Warning: Before removing or replacing modulesSWITCH OFF or ISOLATE the ELECTRICITYSUPPLY to the host machine.
THIS MANUAL IS PROVIDED FOR USE ONLY BY PERSONNELTRAINED TO UNDERTAKE ELECTRICAL INSTALLATION.
330.PROD.GB.4 : 330.GEN.OVIEW.NONE.NONE.GB.3 Black 2
2 ©, Mars, Inc., 1995
CashFlow 330 acceptor Product Maintenance Handbook
OVERVIEW
The CashFlow 330 acceptor is made up of five basic modules,each of which is available in a number of variants:
• Accept Gate• Discriminator• Back Cover• Interface PCB• Interface PCB Cover
The acceptors are provided as standard with a serial interface. Thisinterface is also known as the HI2 interface.
Interface PCB’s are available which provide compatibility withearlier products.
Although a number of variants of acceptor are available the basicoperational principles remain the same.
Interface PCBCover
Discriminator
Back Cover
Interface PCB
Accept Gate
330.PROD.GB.4 : 330.GEN.FPLAT.NONE.NONE.GB.3 Black,White 3
©, Mars, Inc., 1995. 3
CashFlow 330 acceptor Product Maintenance Handbook
INSTALLATION
MINI AND MIDI FRONT PLATES
4. Connect any looms
1. Press acceptor squarelyon to front plate ensuringthat the boss on its base islocated firmly into hole onbottom clip
3.Engage back cover clip
2. Engage front plate clip
Bottom clip
NOTE: The same processis used with both typesof front plate
330.PROD.GB.4 : 330.GEN.FPLAT.NONE.NONE.GB.3 Black,White 4
4 ©, Mars, Inc., 1995.
CashFlow 330 acceptor Product Maintenance Handbook
MAXI FRONT PLATE
Acceptor Retaining Clip
AcceptorConnecting
Points
1. Locate all connection points squarely together.
2. Ensure that retaining clip at upper left is secured.
3. Engage firmly any looms to rear of acceptor.
Acceptor Retaining Clip
330.PROD.GB.4 : 330.GEN.CH_MT.NONE.NONE.GB.3 Black,White 5
©, Mars, Inc., 1995. 5
CashFlow 330 acceptor Product Maintenance Handbook
CHANNEL MOUNTED
The acceptor can be mounted in a 4" moulded channel, a 5" metalchannel or an industry standard channel forming part of the hostmachine
A remote reject unit can be used in conjunction with the 4" channel.
4" CHANNEL INSTALLATION
1 At least 3 of the lugs on the side of the channel must beutilised and firmly fitted onto the host machine.
2 Firmly engage looms to the rear of the acceptor.
3 Engage all location points of the acceptor and channel,and ensure that retaining clip at top left is engaged
4 Confirm that looms are not trapped or damaged
5 Switch on the machine and test the unit.
Acceptor in 4” Channel
330.PROD.GB.4 : 330.GEN.CH_MT.NONE.NONE.GB.3 Black,White 6
6 ©, Mars, Inc., 1995
CashFlow 330 acceptor Product Maintenance Handbook
REMOTE REJECT UNIT INSTALLATION
4" channel and Remote Reject Unit
1 Hold the unit at an angle so that the lugs on the rightbottom edge of the unit (A) can engage into the top ofthe channel (B).
2 Pivot the unit downwards and insert the bottom of theunit (C) into the rear of the channel (D) engagingretaining clip at (C).
3 Connect machine loom at point (E). Test to ensurecorrect fitting.
E
DB
C
A
330.PROD.GB.4 : 330.GEN.CH_MT.NONE.NONE.GB.3 Black,White 7
©, Mars, Inc., 1995. 7
CashFlow 330 acceptor Product Maintenance Handbook
5" CHANNEL MOUNTING
To achieve this satisfactorily the acceptor must first be mounted intoan MEI industry standard adaptor.
1 Ensure that the channel to be used is secured firmly intothe host machine.
2 Fit the acceptor into the adaptor, making firm contactwith location points and the retaining clip.
3 Ensure coin cup front is fitted at top of acceptor.
4 Firmly connect the looms to the acceptor, ensuring thatthey are not trapped.
5 Fit the adaptor into the Channel. Check position oflooms.
6 Switch on the machine and test the unit.
LocatingPoint
LocatingPoints
RetainingClip
Coin CupFront
LocatingPoints
330.PROD.GB.4 : 330.GEN.INIT_TST.NONE.NONE.GB.3 Black 8
8 ©, Mars, Inc., 1995.
CashFlow 330 acceptor Product Maintenance Handbook
INITIALISING
After installing the acceptor into the host machine the followingchecks should be made.
1 Press the reject button on the outside of the hostmachine. The reject lever should operate on theacceptor and the flight deck lid should open freely.
2 Release the reject button and the flight deck lid shouldclose fully. Ensure the lid is closed correctly and not leftpartly open.
3 Insert at least one of each coin/token type and checkthat they are all accepted.
4 Check that the coins are routed to the correct acceptand reject routes.
If for any reason the unit does not work correctly then refer to theFault-Finding chart.
NOTE.
For front plate mounted acceptors the reject lever is located to theback of the back cover.
For top entry mounted acceptors the reject lever is located to the topof the back cover.
Machine Interface
Host InterfaceHI2
RejectLever
Reject Lever
Front Entry Version Top Entry Version
330.PROD.GB.4 : 330.GEN.CONFIG.NONE.NONE.GB.3 Black,White 9
©, Mars, Inc., 1995. 9
CashFlow 330 acceptor Product Maintenance Handbook
CONFIGURATION
FACTORY CONFIGURATION
The CashFlow 330 acceptor is configured for:• Serial interface
and / or• Parallel interface
The accept gate modules are factory configured for specific producttypes. It is therefore essential that if you need to change the acceptgate you change like for like.
Specific Coinsets
The acceptor is pre-programmed to accept a specific range of coinsand/or tokens from the following countries.
This list does not preclude any other coinsets not specifically listed.
Australia Hungary Singapore
Austria India South Africa
Bahrain Israel South Korea
Belgium Italy Spain
Canada Japan Sweden
Colombia Kuwait Switzerland
Cyprus Malta Taiwan
Denmark Mexico Turkey
Eire Netherlands UAE
Finland New Zealand UK
France Norway USA
Germany Portugal
Greece Saudi Arabia
330.PROD.GB.4 : 330.GEN.CONFIG.NONE.NONE.GB.3 Black,White 10
10 ©, Mars, Inc., 1995
CashFlow 330 acceptor Product Maintenance Handbook
FIELD CONFIGURATIONThe CashFlow® 330 acceptor product offers various fieldconfiguration options. There are two methods available: via aninterface PCB (MMI) or by use of a Mars® Route Alpha 250 handheld terminal.
VIA MAN MACHINE INTERFACE (MMI)
The Man Machine Interface is designed to provide a simple stand-alone interface which allows frequently used functions to beaccessed and varied by an operator or route person.
The actual interface consists of a 4-bit DIL switch on the machineinterface PCB. The following functions are available:
• Inhibit an individual coin• Enable an individual coin
To change the function of the product there is a sequence of eventsthat must be followed in order:
1 Switch off power and remove the acceptor module fromthe machine.
2 Disconnect the loom(s).
3 Remove the interface PCB cover by pressingdownwards in the direction of the arrow on the cover.
4 Re-connect the loom(s).
5 Switch on power to the acceptor module.
6 Adjust the switch positions on the 4-bit DIL switch.
7 Replace the acceptor module back into machine.
8 Press the reject lever within a 4 minute time-out period.
9 Insert coins until desired function has been achieved.
10 Press the reject lever.
Set to enable a coin Interface PCB
4-bit DIL switch
330.PROD.GB.4 : 330.GEN.CONFIG.NONE.NONE.GB.3 Black,White 11
©, Mars, Inc., 1995. 11
CashFlow 330 acceptor Product Maintenance Handbook
Important points to remember• The acceptor module must be powered up before
changing the switch positions.• The reject lever must be pressed within the 4
minute timeout period to return to the normaloperational mode.
Care should be taken while the acceptor is not mounted in themachine.
To Inhibit a Coin
1 Adjust slide switches to: 1=ON, 2=ON, 3=OFF, 4=ON.
2 Press the reject lever.
3 Insert coins to be inhibited until they are accepted.
4 Press the reject lever to return to operational mode.
To Enable a Coin
1 Adjust slide switches to: 1=ON, 2=ON, 3=OFF, 4=OFF.
2 Press the reject lever.
3 Insert coins to be enabled until they are accepted.
4 Press the reject lever to return to operational mode.
When you have completed configuring the acceptor module theinterface PCB cover needs to be replaced. To do this follow theinstructions below:
1 Switch off power and remove the acceptor module fromthe machine.
2 Disconnect the loom(s). When disconnecting hold downthe interface PCB before pulling on the loom.
3 Replace the interface PCB cover.
4 Re-connect the loom(s).
5 Place the acceptor module back into the machine.
6 Switch on power.
7 Test the unit to ensure it is working correctly.
330.PROD.GB.4 : 330.GEN.CONFIG.CF_850.NONE.GB.3 Black,Red 12
12 ©, Mars, Inc., 1995.
CashFlow 330 acceptor Product Maintenance Handbook
VIA MARS ROUTE ALPHA 250 TERMINAL
The Mars Route Alpha 250 terminal is used to check or changecertain data held at addresses which affect the way the acceptoroperates. Each address has a unique number which identifies thefeature you wish to read or change.
The following pages will explain how to access and change the datain certain addresses. At the end of this section there is a list ofaddresses and the allowed values.
The terminal is connected via a six way terminal connector at thefront of the acceptor module as shown in the above diagram.
CashFlow® 330 connections to Terminal
Mars® Route Alpha Terminal
330.PROD.GB.4 : 330.GEN.CONFIG.CF_850.NONE.GB.3 Black,Red 13
©, Mars, Inc., 1995. 13
CashFlow 330 acceptor Product Maintenance Handbook
Key Functions
Reset Key: used to reset all modes and to initialise any settings thatyou have changed. If the reset key is pressed while an address isbeing updated then the address may not be updated. The reset keymust be pressed to activate the changes that you have made.
Up Key: used to increase the value displayed on the screen.
Down Key: used to decrease the value displayed on the screen.
Left Key: used to scroll the display to the left when a large numberis being accessed that cannot be fully displayed on the screen.
Right Key: used to scroll the display to the right when a largenumber is being accessed that cannot be fully displayed on thescreen.
Enter Key: used to change between the address and data displays.
Other Facilities Of The TerminalThe terminal has built-in features to speed up its use, including theability to scan at a higher speed with the keys auto repeating, toautomatically roll over from its highest to lowest address and toinform the operator should a communication error occur.Auto Repeating KeysIf either the UP or DOWN keys are kept pressed they automaticallyrepeat. The repeat speed of the key increases the longer the key isheld down.
DISPLAY
RESET
ENTERUP
RIGHT
DOWN
LEFT
330.PROD.GB.4 : 330.GEN.CONFIG.CF_850.NONE.GB.3 Black,Red 14
14 ©, Mars, Inc., 1995.
CashFlow 330 acceptor Product Maintenance Handbook
Double Click HotkeyingIf a key is doubled clicked (pressed twice in quick succession) thenthis causes the address number to increment by a larger amount.e.g. if the user starts at address number 1 then double clicks the UPkey, the address will jump to 40, double click again the address willjump to address 100 etc. You can also double click the DOWN keyto decrement by larger amounts.Using The Terminal
As soon as the terminal is connected to an acceptor it powers upand interrogates the product.
The terminal display will clear and briefly show a message thatindicates the version of software in the terminal. A display of [0 1.0]means software with a version number of 1.0 is fitted in the terminal.
After a few seconds the display will show the number [1.] or [1.-]. Notall configuration items are applicable to every product but all theaddress values are shown on the display. If the value for theaddress is applicable to the product a dash will be present at the farright position on the display. The value can then be accessed andchanged if required
.
Power up message Software version = 1.0
No dash displayed.Address is notaccessible for thisproduct
Dash is displayed.Address is thereforeaccessible
330.PROD.GB.4 : 330.GEN.CONFIG.CF_850.NONE.GB.3 Black,Red 15
©, Mars, Inc., 1995. 15
CashFlow 330 acceptor Product Maintenance Handbook
The basic operation to alter the information held in an address is:
1 Connect the terminal to the CashFlow acceptormodule.
2 Wait for the terminal to power up correctly.
3 Select the address by using the UP and DOWN keys.
4 Examine the data by pressing the ENTER key.
5 Alter the data value by pressing the UP or DOWN keysuntil the new value has been reached.
6 Press the ENTER key to return to displaying addresses.
7 Press the RESET key to initialise the new value.
When the terminal is displaying values stored at addresses, nodecimal point will be displayed.
If an error occurs with the communication between the terminal andthe acceptor the display will show an error message of four halfheight zeroes.
This message will stay on the display. Pressing the ENTER key willthen revert the display to showing the current address. If the erroroccurred while updating an address then the value of that addressshould be checked as it may not have been updated correctly.
As the screen is capable of only displaying four digits at any onetime the number displayed on the screen can be scrolled if it isgreater than 9999 by using the LEFT and RIGHT keys. The left orrightmost digit will flash indicating an extra digit can be examined byuse of the scrolling keys e.g. Value is 12345
Error message
Press RIGHT key
Press LEFT key
Flashing Flashing
330.PROD.GB.4 : 330.GEN.CONFIG.CF_850.NONE.GB.3 Black,Red 16
16 ©, Mars, Inc., 1995.
CashFlow 330 acceptor Product Maintenance Handbook
The tables below show you how the addresses can be reconfiguredand their possible values.
Ad
dre
ss
Par
amet
er
Ran
ge
Mea
nin
g
1 Coin 1 inhibit 0-1 0 = coin allowed,1 = inhibited
2 Coin 2 inhibit 0-1 0 = coin allowed,1 = inhibited
3 Coin 3 inhibit 0-1 0 = coin allowed,1 = inhibited
4 Coin 4 inhibit 0-1 0 = coin allowed,1 = inhibited
5 Coin 5 inhibit 0-1 0 = coin allowed,1 = inhibited
6 Coin 6 inhibit 0-1 0 = coin allowed,1 = inhibited
7 Coin 7 inhibit 0-1 0 = coin allowed,1 = inhibited
8 Coin 8 inhibit 0-1 0 = coin allowed,1 = inhibited
9 Coin 9 inhibit 0-1 0 = coin allowed,1 = inhibited
10 Coin 10 inhibit 0-1 0 = coin allowed,1 = inhibited
11 Coin11 inhibit 0-1 0 = coin allowed,1 = inhibited
12 Coin12 inhibit 0-1 0 = coin allowed,1 = inhibited
13Coin13 inhibit(Serial acceptor only)
0-1 0 = coin allowed,1 = inhibited
14Coin14 inhibit(Serial acceptor only)
0-1 0 = coin allowed,1 = inhibited
15 Accept direction 0-1 0 = left,1 = right
16 Strobes 1/2/4/8
Value = sum of codes1 = direction strobe left2 = direction strobe right4 = post gate left,8 = post gate right
21 Coin 1 type 0-20 = coin1 = value token2 = vend token
22 Coin 2 type 0-20 = coin1 = value token2 = vend token
330.PROD.GB.4 : 330.GEN.CONFIG.CF_850.NONE.GB.3 Black,Red 17
©, Mars, Inc., 1995. 17
CashFlow 330 acceptor Product Maintenance Handbook
23 Coin 3 type 0-20 = coin1 = value token2 = vend token
24 Coin 4 type 0-20 = coin1 = value token2 = vend token
25 Coin 5 type 0-20 = coin1 = value token2 = vend token
26 Coin 6 type 0-20 = coin1 = value token2 = vend token
27 Coin 7 type 0-20 = coin1 = value token2 = vend token
28 Coin 8 type 0-20 = coin1 = value token2 = vend token
29 Coin 9 type 0-20 = coin1 = value token2 = vend token
30 Coin 10 type 0-20 = coin1 = value token2 = vend token
31 Coin11 type 0-20 = coin1 = value token2 = vend token
32 Coin 12 type 0-20 = coin1 = value token2 = vend token
33Coin 13 type(Serial acceptor only)
0-20 = coin1 = value token2 = vend token
34Coin 14 type(Serial acceptor only)
0-20 = coin1 = value token2 = vend token
Ad
dre
ss
Par
amet
er
Ran
ge
Mea
nin
g
330.PROD.GB.4 : 330.GEN.CONFIG.CF_850.NONE.GB.3 Black,Red 18
18 ©, Mars, Inc., 1995.
CashFlow 330 acceptor Product Maintenance Handbook
140,143,146,149,152,155,158,161,
Inhibit lines 1 - 8,inhibits map part i
0 -15Value = sum of codes where1/2/4/8 = coins 1/2/3/4
141,144,147,150,153,156,159,162.
Inhibit lines 1 - 8,inhibits map part ii 0 -15
Value = sum of codes where1/2/4/8 = coins 5/6/7/8
142,145,148,151,154,157,160,163.
Inhibit lines 1 - 8,inhibits map part iii 0-15
Value = sum of codes where1/2/4/8 = coins 9/10/11/12
164,166,168,170,172,174,176,178,180,182,184,186
Coins 1-12 outputmap part i
0-15Value = sum of codes where1/2/4/8 = outputs a/b/c/d
165,167,169,171,173,175,177,179,181,183,185,187
Coins 1-12 outputmap part ii 0-15
Value = sum of codes where1/2/4/8 = outputs e/f/g/h
188 Inhibit pull up polarity 0-1 0 = pull down 1 = pull up
189 Master inhibit polarity 0-1 0 = active high 1 = active low
190External inhibitenable
0-1 0 = disabled 1 = enabled
191 FIB enable 0-1 0 = disabled 1 = enabled
Ad
dre
ss
Par
amet
er
Ran
ge
Mea
nin
g
330.PROD.GB.4 : GEN.GEN.CLEAN.NONE.NONE.GB.7 Black 19
©, Mars, Inc., 1995. 19
CashFlow 330 acceptor Product Maintenance Handbook
CLEANING THE ACCEPTOR
In order to ensure maximum efficiency from this product it isessential to pay regular attention to the cleaning of the coinpathway. Before attempting to clean or remove the acceptor themachine should be switched off. The shaded areas shown in thediagram below should always be kept free from dirt, grease, etc. Anycleaning should be carried out by using a soft damp cloth.Thesurface should always be left clean and dry after any such cleaning.
Should any drops of water enter the product leave machineswitched off for sufficient time to dry out before switching on again.
Never use solvents to clean this product as this will damage thesurfaces.
Note: Failure to switch the machine off before cleaning could resultin a possible delay in accepting coins.
The acceptor calibrates itself at power up and re-calibrates every 4minutes, 5 seconds after a coin has been rejected, or 5 secondsafter the deck is closed. If you switch on with the lid open it willcalibrate itself incorrectly and, if a coin is inserted within 5 secondsof the deck being closed, it will be rejected. Subsequent coins willfollow the normal process of validation provided that the lid is firmlyclosed.
330.PROD.GB.4 : 330.GEN.FFIND.NONE.NONE.GB.3 Black 20
20 ©, Mars, Inc., 1995
CashFlow 330 acceptor Product Maintenance Handbook
FAULT-FINDING
Problem Possible cause Remedy
All coins/tokensrejected
No power to module Check supplyvoltage
Looms dislodged Check loominstallation
Dirt build up Clean acceptor andretry
Acceptorre-calibrating onpower up
Switch machine offand on again
Flight deck lid notfirmly closed
Ensure flight decklid is closed correctly
Poor coinacceptance
Modules notmounted correctly
Check alignment
Dirt build up Clean acceptor andretry
Rejects onetype coin/token
Inhibit set Check coin/token isenabled and notinhibited
Coins acceptedbut no credit
given
Looms not correctlyinserted
Check loominstallation
Coins notrouting correctly
Incorrect parts fitted Check that acceptgate is correct type
Check exit plate inadaptor (if fitted) iscorrect type
330.PROD.GB.4 : 330.APPS.HII_IF.NONE.NONE.GB.3 Black,White 21
©, Mars, Inc., 1995. 21
CashFlow 330 acceptor Product Maintenance Handbook
ELECTRICAL INTERFACES
HOST INTELLIGENT INTERFACE (HI2)
The HI2 interface offers serial control of the following functions:• Inhibiting Coins• Enabling Coins
The connections to the 10 way connector of the HI2 are shownbelow.
Viewed from loom end
Electrical Specifications
I/O PortsData and Busy
Input high voltage Vih 8.0V min. VIN + 1.5Vmax
Input low voltage Vil GND - 1.5V min 1.3V max.
Input impedance Rp 4.7KΩ nom. to VIN
Output high voltage Voh 9.0Vmin. VIN max.
Output low voltage Vol GND min. 0.5V max.
Output sink current Iol ------- 25mA max.
PIN SIGNALNAME PIN SIGNAL NAME
1 DATA 2 GND
3 BUSY 4 GND
5 RESET 6 POWER FAIL
7 VIN 8 VNEG
9 RESERVED 10 VSOL
1
2
3
4
5
6
7
8
9
10
330.PROD.GB.4 : 330.APPS.HII_IF.NONE.NONE.GB.3 Black,White 22
22 ©, Mars, Inc., 1995.
CashFlow 330 acceptor Product Maintenance Handbook Data and Busy line equivalent circuit
The Data and Busy lines are active low signals and are designed tobe wire-ORed with other HI2 nodes. The selector represents an HI2
system load of 3 units.
Reset
Input high voltage Vih Open circuit or > 3.5V (5.5Vmax.)
Input low voltage Vil (GND - 0.5V) min. 0.9Vmax.
Input impedance Rp 47kΩ nom. to + 5V
Input capacitance Cin 1.5µF nom.
Input series resist. Rserl 56Ω nom.
In addition to the on-board power-on reset circuit, an external devicemay reset the system by pulling RESET low. The RESET line isactive low and is intended to be driven by an open collectortransistor referenced to 0V. A series resistor is provided to limit thepeak current drawn when the on-board reset capacitor is dischargedby an external device.
+5VVIN
DATA or BUSY
GND
To internallogic
Rp47K
47K1n
Rx
Tx
0V
330.PROD.GB.4 : 330.APPS.HII_IF.NONE.NONE.GB.3 Black,White 23
©, Mars, Inc., 1995. 23
CashFlow 330 acceptor Product Maintenance Handbook
PF (Power Fail)
Input high voltage Vih 3.7V min. 5.5V max.
Input low voltage Vil (GND - 0.5V) min. 0.9Vmax.
Input impedance Rp 4.7kΩ nom. to + 5V
In addition to the on-board power fail circuit, there is an input on thehost connector to allow an external device to warn of an impendingpower failure. The power fail input is active low and is intended to bedriven by an open collector transistor referenced to 0V.
VIN (Power)
Input supply voltage Vin 10V min. 15V max.(Abs.max. not operational 20V)
Supply voltage ripple Vrip Within Vin min. to max. up to100Hz
250mV pk-pk frequencies >100Hz
Supply rise time Trise 75ms max.
Input current Iin 500mA max.
VIN is the input supply voltage referenced to the supply return,VNEG.
VNEG is connected to GND on the acceptor.
330.PROD.GB.4 : 330.APPS.HII_IF.NONE.NONE.GB.3 Black,White 24
24 ©, Mars, Inc., 1995.
CashFlow 330 acceptor Product Maintenance Handbook
APPLICATIONS SUPPORT
The Host Intelligent Interface (HI2) is a high functionality interface forpoint to point or multi node systems.
It is currently only available under licence and confidentialityagreements.
Applications support for HI2 is in the form of documentation andsupport. These are all intended to make it straightforward to design-in the interface.
HI2 Applications Support
Documentation LibrarySoftware
ProtocolSupport
Tools
ImplementorsGuide
‘C’ 6805 8051
ProtocolMonitor
330.PROD.GB.4 : 330.APPS.HII_IF.NONE.NONE.GB.3 Black,White 25
©, Mars, Inc., 1995. 25
CashFlow 330 acceptor Product Maintenance Handbook
SUPPORT TOOLS
With the use of a HI2 interface adaptor and with the aid of the special“Protocol Monitor” software application it is possible to connect a PCserial port to the HI2 signals.
The adaptor should be plugged into the PC serial port and wired tothe HI2 bus as shown below.
HI2 InterfaceAdaptor
ProtocolMonitor
+12V (Standard products)0V
Reset Switch(if required)
10 WayProduct
Connector
10 Way HI2Adaptor
ConnectorPF
Reserved
VIN
123456789
10
123456789
10
330.PROD.GB.4 : 330.GEN.CUST_IF.0V_COMM.NONE.GB.3 Black,White 26
26 ©, Mars, Inc., 1995.
CashFlow 330 acceptor Product Maintenance Handbook
MACHINE INTERFACE PCB’s
All CashFlow® coin products incorporate a serial machine interfacecalled HI2 which offers maximum communication flexibility andsecurity.
Machine interface PCB’s are used to provide compatibility toindustry standard interfaces. There are five different types available,these are:
• Standard version 112, (0V Common 12V)• Standard version 124, (0V Common 24V)• Standard version 212 (0V Common 12V)• Standard version 312 (0V Common 12V)• Dual Polarity (12V)
Please note: Not all interfaces are available for all productconfigurations. Please contact your Mars Electronics Internationalrepresentative for guidance.
The interface PCB’s are attached directly to the discrimination PCBand are enclosed within the back cover of the acceptor.
All of the PCB’s contain a four-bit DIL switch known as the ManMachine Interface (MMI). This switch can be used to configurecertain aspects of the product.
COMPATIBILITYStandard versions 112 and 124 are compatible with the following:
MS130, MS135, MS130B1, MS135B1, MS180 and MS185.
Standard version 212 is compatible with:
NRI G13.
Standard version 312 is compatible with:
Azkoyen L60.
Dual Polarity version is compatible with:
MS111, MS111B1, MS115, ME111.
330.PROD.GB.4 : 330.GEN.CUST_IF.0V_COMM.NONE.GB.3 Black,White 27
©, Mars, Inc., 1995. 27
CashFlow 330 acceptor Product Maintenance Handbook
STANDARD VERSIONS 112 and 124, (0V COMMON 12V & 24V)
These PCB’s provide for 6 coin output lines and 6 individual inhibitinputs, an all-inhibit input, a flight deck open (ER) output and fourroute inhibit inputs.
Standard version 112 (0V Common 12V) interface PCB
Standard version 124 (0V Common 24V) interface PCB
PCB Connectors - versions 112 and 124
The coin outputs are defined as outputs OPA to OPF, and the inhibitinputs are defined as inputs INHA to INHF. The all-inhibit input isdefined as input ALLINHB, with the flight deck open output beingER. The route inhibits are defined as inputs INHR1 to INHR4.
The 6 coin outputs consist of open collector transistors referencedto 0V. The appropriate output becomes active for between 80ms to120ms to indicate that a particular coin has been accepted.
The 6 individual coin inhibit inputs consist of CMOS inputs with inputprotection and pull-down resistors. The inputs are active high toinhibit coins and if left open circuit will default to accepting coins.
The all-inhibit input consists of a CMOS input with input protectionand pull-up resistor. The input is active low to inhibit coins and if leftopen circuit will default to accepting coins.
The flight deck open output consists of an open collector transistorreferenced to 0V. The output is active low to indicate that the flight
330.PROD.GB.4 : 330.GEN.CUST_IF.0V_COMM.NONE.GB.3 Black,White 28
28 ©, Mars, Inc., 1995.
CashFlow 330 acceptor Product Maintenance Handbook
deck is open and will remain active for a maximum of 500ms.
Connector locations - versions 112 and 124
The four route inhibit inputs consist of CMOS inputs with inputprotection and pull-up resistors. The inputs are active low to inhibita route and if left open circuit will default to route enabled. A shortinglink is required between pins 1 and 2 of the shorting link connectorto enable this mode of operation.
Interface connector - versions 112 and 124
Shorting Link Connector - version 112 and 124
Conn.Pin Signal Name Signal Name Conn.
Pin
1 INHC INHE 2
3 INHD INHF 4
5 ER ALLINHB 6
7 OPC GND 8
9 OPF OPD 10
11 OPE OPB 12
13 OPA INHB 14
15 INHA VSUPPLY 16
Conn.Pin Signal Name Signal Name Conn.
Pin
INHF LINK
1
3 RESERVED IF 2
1
Back Cover
Pin 1Route InhibitConnector
Pin 1Shorting LinkConnector
Pin 1InterfaceConnector
330.PROD.GB.4 : 330.GEN.CUST_IF.0V_COMM.NONE.GB.3 Black,White 29
©, Mars, Inc., 1995. 29
CashFlow 330 acceptor Product Maintenance Handbook
Route Inhibit Connector - versions 112 and 124
Electrical Interfaces - versions 112 and 124
PowerFor 12V operation, VSUPPLY (pin 16) referenced to GND (pin 8):
Input supply voltage Vin 10V min. 15V max.(Abs.max. not operational 20V)
Supply voltage ripple Vrip Within Vin min. to max. up to100Hz
250mV pk-pk frequencies>100Hz
Supply rise time Trise 75ms max.
Input current Iin 500mA max. Acceptor only
Outputs
Off State voltage Voff +30V max.
Leakage current Lin 5µA
On state voltage Vcesat 0.5V max.
On state current Ic 30mA max.
Conn.Pin Signal Name
1 GND
2 POLARISED(Loom To HaveBlanked Receptacle)
3 INHR4
4 INHR3
5 INHR2
6 INHR1
330.PROD.GB.4 : 330.GEN.CUST_IF.0V_COMM.NONE.GB.3 Black,White 30
30 ©, Mars, Inc., 1995.
CashFlow 330 acceptor Product Maintenance Handbook
Inputs (INHA - INHF)Individual coin inhibit inputs - (INHA-INHF) Pins 1,2,3,4,14 and 15
Inhibit coins Vin > + 4V (+30V max)
Accept coins Vin between 0V and +1V or inputopen circuit
Input impedance 47kΩ nom. to 0V
INHA-F Input Equivalent Circuit
All-Inhibit Input: (ALLINHB) Pin 6
Accept coins Vin > + 4V (+ 30V max.) or inputopen circuit
Inhibit coins Vin between 0V and + 1V
Input impedance 47kΩ nom. to + 5V
Route Inhibit inputs: (INHR 1-4) Pins 3, 4,5,6
Route enabled Vin > + 4V (30V max.)
or input open circuit
Route inhibited Vin Between 0V and +1V
Input impedance: 47kΩ nom. to + 5V
All-inhibit and Route inhibit input equivalent circuit
47KINHIBIT
+5V
INPUTS
47KCMOSINPUT
0V
To internallogic
47K
INHIBIT
To internallogic
+5V
INPUT
47K
CMOSINPUT
+5V
330.PROD.GB.4 : 330.GEN.CUST_IF.0V_COMM.NONE.GB.3 Black,White 31
©, Mars, Inc., 1995. 31
CashFlow 330 acceptor Product Maintenance Handbook
STANDARD VERSIONS 212 and 312, (0V COMMON 12V)
This PCB provides two quite separate interfaces. Version 212 has 6coin output lines, an all-inhibit input and a flight deck open (ER)output. This interface operates from a +12V supply.
Version 312 has 4 coin outputs, an alarm output or inhibit input andan all-inhibit input. This interface operates from a +12V supply.Provision has also been made for two route inhibit inputs.
Versions 212 and 312 (0V Common 12V) Interface PCB
PCB Connectors - version Standard 212
The six coin outputs consist of open collector transistors referencedto 0V. The appropriate output becomes active for between 80ms to120ms to indicate that a particular coin has been accepted.
The coin outputs are defined as outputs OPA to OPF.
ConnectorPin Signal Name Signal Name Connector
Pin
1 GND VSUPPLY 2
3 OPE OPF 4
5 ER ALLINH 6
7 OPA OPB 8
9 OPC OPD 10
Pin 1Pin 10
Connector locations - Version 212
330.PROD.GB.4 : 330.GEN.CUST_IF.0V_COMM.NONE.GB.3 Black,White 32
32 ©, Mars, Inc., 1995.
CashFlow 330 acceptor Product Maintenance Handbook
The all-inhibit input consists of a CMOS input with input protectionand pull-down resistor. The input is active high to inhibit coins and ifleft open circuit will default to accepting coins. The all-inhibit input isdefined as input ALLINH
The flight deck open output consists of an open collector transistorreferenced to 0V. The output is active low to indicate that the flightdeck is open and will remain active for a maximum period of 500ms.The flight deck open output is defined as output ER.
PCB Connectors - version Standard 312
The four coin outputs consist of open collector transistorsreferenced to 0V. The appropriate output becomes active forbetween 80ms to 120ms to indicate that a particular coin has beenaccepted. The coin outputs are defined as outputs OPA to OPD.
The alarm output consist of an open collector transistor referencedto 0V. The output becomes active, if enabled, when the acceptordetects a fraud condition. The alarm output is defined as outputALARM /INH.
The same interface pin is also used for an inhibit input whichconsists of a CMOS input with input protection and pull-up resistor.The input is active high to inhibit coins and if left open circuit willdefault to inhibiting coins. The input may be configured via theacceptor inhibit map, to inhibit some or all of the coins in the coin set.
ConnectorPin
1 2 3 4 5 6 7 8 9 10
SignalName
VS
UP
PLY
GN
D
OP
A
OP
B
OP
C
ALL
INH
OP
D
INH
R1
INH
R2
ALA
RM
/INH
Pin 1Pin 10
Connector locations - Version 312
330.PROD.GB.4 : 330.GEN.CUST_IF.0V_COMM.NONE.GB.3 Black,White 33
©, Mars, Inc., 1995. 33
CashFlow 330 acceptor Product Maintenance Handbook
The inhibit input is defined as input ALARM/INH. The all-inhibit inputconsists of a CMOS input with input protection and pull-up resistor.The input is active high to inhibit coins and if left open circuit willdefault to inhibiting coins. The input may be configured via theacceptor inhibit map, to inhibit some or all of the coins in the coin set.The all-inhibit input is defined as input ALLINH.
Electrical Interfaces
PowerStandard 2 interface; VSUPPLY (pin 2) referenced to GND (pin1):Standard 3 interface; VSUPPLY (pin 1) referenced to GND (pin2):
Input supply voltage Vin 10V min. 15V max.
(Abs. max. not operational 20V)
Supply voltage ripple Vrip Within Vin min. to max. up to100Hz250mV pk-pk frequencies >100Hz
Supply rise time Trise 75ms max.
Input current. Iin 500mA max. Acceptor only
OutputsAll outputs:
Off state voltage Voff +30V max.
Leakage current Iin 5µA
On state voltage Vcesat 0.5V max.
On state current Ic 30mA max.
Standard 2; All-inhibit input (ALLINH)
Inhibit coins Vin > +4 V (+30V max)
Accept coins Vin between 0V and +1Vor input open circuit
Input Impedance: 47kΩ nom. to 0V
330.PROD.GB.4 : 330.GEN.CUST_IF.0V_COMM.NONE.GB.3 Black,White 34
34 ©, Mars, Inc., 1995.
CashFlow 330 acceptor Product Maintenance Handbook
Standard 212 ALLINH input equivalent circuit
Standard 3; Inhibit inputs (ALLINH, ALARM/INH and INHR1-7)
Accept coins Vin > +4 V (+30V max)or input open circuit
Inhibit coins Vin between 0V and +1V
Input Impedance: 47kΩ nom. to +5V
Standard 312 - Inhibit inputs equivalent circuit
47KALL INHIBIT
To internallogic
+5V
INPUT
47KCMOSINPUT
0V
47K
INHIBIT
To internallogic
+5V
INPUTS
47K
CMOSINPUT
+5V
330.PROD.GB.4 : 330.GEN.CUST_IF.DUAL_POL.NONE.GB.3 Black 35
©, Mars, Inc., 1995. 35
CashFlow 330 acceptor Product Maintenance Handbook
DUAL POLARITY
This interface operates from a nominal 12V supply and selfconfigures to either positive or negative common operation. In eithermode of operation this interface offers 6 coin output lines, an outputcommon, 6 individual inhibit inputs and power connections.
Dual Polarity Interface PCB
Coin outputs - positive common
For positive common operation the OPCOM line must be positivewith respect to GND and the coin output lines should be connectedthrough a load to a voltage more negative than the OPCOM line.
Coin outputs - negative common
For negative common operation the OPCOM line must be negativewith respect to GND or connected to GND. The coin output linesshould be connected through a load to a voltage more positive thanthe OPCOM line.
With either of these options it is possible to operate in a pulsedmode by allowing the OPCOM line to float until it is polled by thehost machine.
When a coin is accepted one of the coin output lines becomesactive.
330.PROD.GB.4 : 330.GEN.CUST_IF.DUAL_POL.NONE.GB.3 Black 36
36 ©, Mars, Inc., 1995.
CashFlow 330 acceptor Product Maintenance Handbook
PCB Connector - Dual Polarity
The coin outputs are defined as OPA to OPF, and the inhibit inputsas INHA-INHF.
Electrical Specifications
Power
VSUP (pin 11) referenced to GND (pin 12):
Input supply voltage Vin 10V min. 15V max.(Abs. max. not operational 20V)
Supply voltage ripple Vrip Within Vin min. to max. up to 100Hz
250mV pk-pk frequencies > 100Hz
Supply rise time Trise 75ms max.
Input current Iin 1440mA max.
Conn.Pin Signal Name
1 OPA
2 OPB
3 OPCOM
4 OPF
5 POLARISING
6 OPE
7 OPD
8 POLARISING
9 OPC
10 INHC
11 VSUP
12 GND
13 INHD
14 INHE
15 INHF
16 INHB
17 INHA
330.PROD.GB.4 : 330.GEN.CUST_IF.DUAL_POL.NONE.GB.3 Black 37
©, Mars, Inc., 1995. 37
CashFlow 330 acceptor Product Maintenance Handbook
Inputs
Individual coin inhibit inputs:
Inhibit coins Vin > + 4V (+20Vmax) or input opencircuit
Accept coins Vin between 0V and + 1V
Input impedance 12kΩ nom. to + 5V
Inhibit input equivalent circuit
Outputs - Positive Common
OPCOM (pin3) referenced to GND (pin12):
Input voltage Vin 5V min 26V max.
(4.5V min 5V max.Ic max =10mA)
All outputs:
Off state voltage Voff (OPCOM - 27V) min.
Leakage current Iin 5µA
On state voltage Vcesat (OPCOM - 1.5V) min.
On state current Ic 40mA max.
47K
INHIBIT
To internallogic
0V
+5V
INPUT
12K
CMOSINPUT
+5V
330.PROD.GB.4 : 330.GEN.CUST_IF.DUAL_POL.NONE.GB.3 Black 38
38 ©, Mars, Inc., 1995.
CashFlow 330 acceptor Product Maintenance Handbook
Outputs -Negative Common
OPCOM (pin3) referenced to GND (pin12):
Input voltage Vin -22V min. 0V max.
(0V min. 0.5V max. Icmax=10mA)
All outputs:
Off state voltage Voff (OPCOM + 27V) min.
Leakage current Iin 5µA
On state voltage Vcesat (OPCOM + 1.5V) min.
On state current Ic 40mA max
Coin output equivalent circuit
To internallogic
0V
+5V
1N4148
1N4148
CoinOutput
OutputCommon
330.PROD.GB.4 : 330.PROD.MOD_XCHNG.NONE.NONE.GB.4 Black,White 39
©, Mars, Inc., 1995. 39
CashFlow 330 acceptor Product Maintenance Handbook
REPLACING MODULES
REMOVING THE ACCEPTOR FROM TOP ENTRY ADAPTOR
1 Ensure that the machine is powered down.
2 Remove the adaptor (with acceptor fitted) from thechannel.
3 Dis-connect any looms that are connected to theacceptor.
4 Release the retaining clip in the adaptor with a carefulbut firm pull to the right hand side.
5 Tilt the top of the acceptor forward to release it from theretaining clip.
6 Lift the acceptor upwards and pull towards you toremove it from the adaptor.
To replace the acceptor into the adaptor reverse the above process.
Retaining Clip
330.PROD.GB.4 : 330.PROD.MOD_XCHNG.NONE.NONE.GB.4 Black,White 40
40 ©, Mars, Inc., 1995.
CashFlow 330 acceptor Product Maintenance Handbook
REPLACING THE BACK COVER
1 Remove acceptor as previously described
2 Dis-engage any looms.
3 Remove the interface PCB cover.
4 Remove the customer interface PCB if fitted.
5 Release the retaining clips where shown on diagram.You will find it easier if you use a small screwdriver.
6 Gently ease out the discriminator module from the backcover.
For re-assembly reverse the above instructions.
Left and Right Hand Clip Positions
Clip 1
Clip 3
Clip 2
Clip 4
330.PROD.GB.4 : 330.PROD.MOD_XCHNG.NONE.NONE.GB.4 Black,White 41
©, Mars, Inc., 1995. 41
CashFlow 330 acceptor Product Maintenance Handbook
REMOVING THE ACCEPT GATE
1 Remove the acceptor module.
2 Remove the back cover, observing the earlierinstructions on removing the discriminator, from theback cover.
3 Dis-engage the PCB at the rear by releasing theretaining clip on the upper left hand side of it. Extremecare should be taken not to damage the flexi-circuitleading to the PCB while it is dis-engaged.
The accept gate is held in the discriminator via three clips
Release the clip at the pointshown in direction of arrow.Gently ease accept gatemodule outwards away fromdiscriminator.
Dis-engage the clip at thebase of the accept gate andseparate gently the two partsin the direction of the arrow.
Pressing the side of theaccept gate at the pointindicated, and keeping theaccept gate parallel to thediscriminator, pull it free fromits electrical connections,taking care not to bend the
Rear view of discriminator
View under accept gate
View to right of accept gate
330.PROD.GB.4 : 330.PROD.MOD_XCHNG.NONE.NONE.GB.4 Black,White 42
42 ©, Mars, Inc., 1995.
CashFlow 330 acceptor Product Maintenance Handbook
To replace the accept gate the discriminator lid must be opened.Great care must be taken because the spring will become dis-engaged if the lid, (which is normally restrained by the back cover),is taken further back than 100˚.
When replacing the accept gate make sure that all three clips arecorrectly aligned before pushing back into place. At all times theflexi-circuit must be treated with care to ensure no damage resultsfrom rough handling.
Should the spring require re-fitting the guides and pivot pointsforming the physical link between the deck and lid must be first becorrectly located, and the spring connected at both ends. The twoparts should be pulled apart and pivoted into the correct position. Atno time should undue force be used as this will cause irreparabledamage to the mouldings and make the discriminator unusable.
Check for correct functionality after re-assembling.
Spring
Lid
Deck
PCB retainingclip
330.PROD.GB.4 : 330.PROD.MOD_XCHNG.NONE.NONE.GB.4 Black,White 43
©, Mars, Inc., 1995. 43
CashFlow 330 acceptor Product Maintenance Handbook
CHANGING THE INTERFACE PCB
1 Unplug the acceptor module from any looms that areattached.
2 Remove the acceptor module from the front plate.
3 Slide off the removable back cover by pressing andpushing downwards in direction of arrows (Fig 1).
4 Carefully lift and remove the Interface PCB (fig.2) takingcare not to bend the connector pins.
Fig 1
Press & PushDown Here
RemovablePCB Cover
Fig 2
Interface PCB
330.PROD.GB.4 : 330.PROD.MOD_XCHNG.NONE.NONE.GB.4 Black,White 44
44 ©, Mars, Inc., 1995.
CashFlow 330 acceptor Product Maintenance Handbook
5 Place the new interface PCB on to the correct pinconnections and push gently but firmly home (fig.3).
6 Replace the PCB cover.
7 Fit the acceptor module back into the front plate.
8 Replace any loom/s, ensuring a firm connection.
9 Switch on mains power and follow the initialisationprocedure to check the unit is working and pricing asrequired.
Fig 3
12 Pins
12 Pin Connector
Interface PCB
330.PROD.GB.4 : 330.PROD.ACCES.NONE.NONE.GB.3 Black 45
©, Mars, Inc., 1995. 45
CashFlow 330 acceptor Product Maintenance Handbook
ACCESSORIES AND SPARES
FRONT PLATES
ADAPTOR & CHANNEL
Mini Front PlateMidi Front Plate
Maxi Front Plate
The Mini and Midi front platescan be supplied with or withoutan integral LCD display.An LED display can be usedwith the Maxi front plate.
The 4" channel providesa frame into which theAcceptor can be directlyfitted.
The 5" top entryadaptor is used inchannel mountedapplications.
4" Moulded Channel5" Top Entry Adaptor
330.PROD.GB.4 : 330.PROD.ACCES.NONE.NONE.GB.3 Black 46
46 ©, Mars, Inc., 1995.
CashFlow 330 acceptor Product Maintenance Handbook
BACK COVERS
There are versions available for front plate and channel mountedacceptors and they simply clip on to the discrimination module.
The reject lever assembly forms part of the back cover assembly.
Reject LeverAssembly
Front Entry version
ChannelMountingPins
Top Entry version
RemovablePCB Cover
Reject LeverAssembly
330.PROD.GB.4 : 330.PROD.ACCES.NONE.NONE.GB.3 Black 47
©, Mars, Inc., 1995. 47
CashFlow 330 acceptor Product Maintenance Handbook
ACCEPT GATE MODULES
The accept gate module contains a solenoid-operated gate, opticalcoin strobes and coin routing components.
There are three variants of accept and reject options available. Thecoin exits for both accepted and rejected coins are defined by thetype of accept gate fitted.
Acc / Rej Coin Exit Options
Reject Right
AcceptRight
Accept Left
Reject Front
AcceptRight
Reject Left
330.PROD.GB.4 : 330.GEN.COMP.CFLOW.NONE.GB.3 Black 48
48 ©, Mars, Inc., 1995.
CashFlow 330 acceptor Product Maintenance Handbook
CASHFLOW MODULES COMPATIBILITY
0V CommonI/F 12v
0V CommonI/F 24v
Dual PolarityI/F 12v
4" Channel
5" TopEntry
Adaptor
Mini F/P
Midi F/P
Maxi F/P
DISCRIMINATOR
AR RLAR RF RR AL
Top EntryTop EntryFront Entry
COIN EXITSViewed from rearRF=Reject Front
AR=Accept Right
RL=Reject Left
RR=Reject Right
AL=Accept Left
Back CoverBack CoverBack Cover
330.PROD.GB.4 : 330.GEN.COMP.MS_ME.NONE.GB.3 Black 49
©, Mars, Inc., 1995 49
CashFlow 330 acceptor Product Maintenance Handbook
COMPATIBILITY with EARLIER PRODUCTS
If you are currently using the MS/ME100 product range then thetable below will help you identify the acceptor and accessoryrequired for compatibility. The typical applications shown are aguide only to the options available.
NEW NEW NEW
AvailableOptions
4" A
ccep
tor
Sta
nd
Alo
ne
4" A
ccep
tor
+To
p E
ntr
y A
dap
tor
4" A
ccep
tor
+Min
i Fro
nt
Pla
te
4" A
ccep
tor
+Mid
i Fro
ntP
late
4" A
ccep
tor
+Max
i Fro
nt
Pla
teTypical
Application
Juke Boxes,Cigarette M/cChannelMounted
Video Games,Table TopVending
PinBallM/c’s
ReplacesMS111
ReplacesME111
ReplacesME115
ReplacesMS130
330.PROD.GB.4 : GEN.GEN.OFF.NONE.NONE.GB.11 Black 50
50 ©, Mars, Inc., 1995.
CashFlow 330 acceptor Product Maintenance Handbook
MARS ELECTRONICS INTERNATIONALOFFICES
AUSTRALIA ITALY
MARS ELECTRONICS INTERNATIONAL302 PARRAMATTA ROADAUBURNNEW SOUTH WALES, 2144TELEPHONE: 2 - 7375390FACSIMILE: 2 - 7375399
MARS ELECTRONICS INTERNATIONAL27011 BELGIOIOSO (PV)VIALE DANTE, 40TELEPHONE: 0382 - 979313FACSIMILE: 0382 - 970790
CANADA JAPAN
MARS ELECTRONICS INTERNATIONAL37, HOLLAND DRIVEBOLTONONTARIO, L7E 5S4TELEPHONE: 416 - 239 - 2782FACSIMILE: 416 - 239 - 3322
MARS ELECTRONICS INTERNATIONALA DIVISION OF MASTER FOODS LTD.3F MUSASHI-KOSUGI TOWER PLACE403 KOSUGIMACHI 1-CHOMENAKAHARA-KUKAWASAKI-SHIKANAGAWA-KEN 211TELEPHONE: 44 - 712 - 1315FACSIMILE: 44 - 712 - 1439
FRANCE SPAIN
MARS ELECTRONICS INTERNATIONALBOULEVARD DES CHANATSBP 745550 ST. DENIS DE L’HOTELTELEPHONE: 38 - 59 - 6161FACSIMILE: 38 - 59 - 6172
MARS ELECTRONICS INTERNATIONAL
M.a DE MOLINA, 40-3a
28006 MADRIDTELEPHONE: 9 - 3379182FACSIMILE: 91- 5635517
GERMANY SWITZERLAND
MARS ELECTRONICS INTERNATIONALINDUSTRIERING 17 A41751 VIERSENTELEPHONE: 02162 - 9560FACSIMILE: 02162 - 41544
MARS ELECTRONICS INTERNATIONALCH. PONT-DU-CENTENAIRE 109PLAN-LES-OUATESP.O. BOX 26501211 GENEVA 2TELEPHONE: 22 - 8840505FACSIMILE: 22 - 8840504
GREAT BRITAIN UNITED STATES
MARS ELECTRONICS INTERNATIONALESKDALE ROADWINNERSH TRIANGLEWOKINGHAMBERKSHIRE, RG41 5AQTELEPHONE: 01734 - 697700FACSIMILE: 01734 - 446412
MARS ELECTRONICS INTERNATIONAL1301 WILSON DRIVEWEST CHESTERPA 19380TELEPHONE: 610 - 4302500FACSIMILE: 610 - 4302694
330.PROD.GB.4 : GEN.GEN.OFF_DIST.NONE.NONE.GB.11 Black 51
CashFlow 330 acceptor Product Maintenance Handbook
©, Mars, Inc., 1995. 51
ARGENTINA
BUGS S.R.L.Electronica Industrial 1602Caracas 558 P.B. 11406 Buenos AiresContact: Sergio Adrian FerroTelephone: 1 - 613 - 2205
AUSTRALIA
BLUEJADE ELECTRONICSUnit 712 Edina RoadFerntree GullyVictoria, 3156Contact: Ross SeymourTelephone: 03 - 9752 - 2730
GALEDON ELECTRONICS92 Lincoln StreetOxleyQueensland, 4075Contact: George HetperTelephone: 07 - 3379 - 3922
MIKE STEWARD ELECTRONICSLot 251Muros PlaceMidvaleWestern Australia, 6055Contact: Mike StewardTelephone: 09 - 274 - 5755
VFJ ELECTRONICS2 Picken streetSilverwaterNew South Wales, 2128Contact: Derek WebsterTelephone: 02 - 648 - 5600
AUSTRIA
FRIEDRICH HOCHHAUSERLinzerstrasse 123A 4614 MarchtrenkContact: Friedrich HochhauserTelephone: 724 - 358407
BELGIUM
CTP NV/SAKernenergietraat 53B - 2610 WilrijkAnversContact: Cam Van Der SteenTelephone: 3 - 825 - 0207
BRAZIL
CIMAQ INDUSTRIA e COMERCIOde MAQUINAS LTDA.Estrada Uniao e Industria 9120 Itaipava257 PetropolisRio de JanieroContact: Paolo Cirelli /Guido CirelloTelephone: 242 - 22 2555
CANADA
ANDRE LABBEE Inc.5600 Vanden AbeeleSt. LaurentQuebec H4S 1P9Contact: Andre LabbeeTelephone: 514 - 333 - 4030
ARBORTRONICS1520 Lodestar Road, Unit 20TorontoOntario M3J 3C1Contact: Motek SzpindelTelephone: 416 - 638 - 6112
MEI DISTRIBUTORSThe Following Distributors Offer A Comprehensive Sales AndReplacement Service For New Product And Spare Parts.
330.PROD.GB.4 : GEN.GEN.OFF_DIST.NONE.NONE.GB.11 Black 52
52 ©, Mars, Inc., 1995.
CashFlow 330 acceptor Product Maintenance Handbook
CROATIA/SLOVENIA
VENDOMAT D.o.o.Vrbice 541030 ZagrebContact: Kresimir BesedicTelephone: 1 - 770040
CZECH REPUBLIC
COMAX LEISURE s.r.o.Plovdivská 3405CR - Praha 8Contact: Jan SubrtTelephone: 2 - 402 - 6881
DENMARK
MØNTSYSTEMMiddlefartvej 11Dk-5000Odense CContact: Erik RavnkildeTelephone: 66 -177744
EIRE
MECHSHOP (IRELAND)Bracetown Office ParkBracetownCloneeCo. MeathContact: John SteenTelephone: 01 - 8251755
FINLAND
MECSELSitratie 3B00420 HelsinkiContact: Seppo SarrivaaraTelephone: 0700 -18620
FRANCE
A.P.S.34 Avenue Du President Wilson93210 La Plaine Saint-DenisContact: Oziel FrédéricTelephone: 1 - 48 09 07 98
BROKERHOUSE DISTRIBUTORS108 Woodbine Downs Blvd., Unit 4RexdaleOnrario M9W 5S6Contact: Greg SuitorTelephone: 416 - 798 - 3537
BROKERHOUSE DISTRIBUTORS4279 PhillipsBurnabyBritish Columbia V5A 2X4Contact:Doug SharpeTelephone:604 - 421 - 2277
CAN-WEST VENDINGDISTRIBUTORS9815 33rd AvenueEdmontonAlberta T6N 1B6Contact: Darren NicklesTelephone: 404 - 861 - 8173
CRANE NATIONAL VENDING595 Middlefield Road, Unit 20ScarboroughOntario M1V 3S2Contact: Steve GordonTelephone: 416 - 291 - 7600
CHILE
SIDEXSan Juan 4519San JoaquinSantiagoContact: Ricardo Solari G.Telephone: 2 - 553 - 1632
COLOMBIA
L.S.I.Ingeneria Electronica Ltda.Calle 86 No. 115 - 07Int.15 - 19A.A. 59271Santafe de Bogota, D.C.Contact: Enrique Ardila /Jaime DiazTelephone: 3 - 333 - 2452
330.PROD.GB.4 : GEN.GEN.OFF_DIST.NONE.NONE.GB.11 Black 53
©, Mars, Inc., 1995. 53
CashFlow 330 acceptor Product Maintenance Handbook
HöR GmbH & Co. INDUSTRIE-ELECTRONIC KGBoschweg 1312057 BerlinContact: Günther HörTelephone: 030 - 6847044
S & M Schaltgeräteservice GmbHRichard-Lucas Strasse 341812 ErkelenzContact: Stefan MeschTelephone: 0 2431 - 6076
GREAT BRITAIN
BRENT LEISURE SPARES LTD.Namco House, Unit 5Acton Vale Industrial EstateThe Vale, ActonLondon W3 7QEContact: Peter MurphyTelephone: 0181 - 324 - 6000
EUROCOIN LTDFortune HouseMoxon StreetBarnetHertsContact: Nick VeitchTelephone: 0181 - 449 - 0077
MECHSHOP (MIDLANDS)Unit 9, Arden Business CentreArden RoadAlcesterWarwickshire B49 6HWContact: Ian SaundersTelephone: 01789 - 763963
MECHSHOP (NORTH)Linnyshaw Industrial EstateSharp StreetWalkdenManchester M28 5WAContact: David BridgeTelephone: 0161 - 790 - 0929
G.T.I.50 Bis rue Maurice Arnoux92120 MontrougeContact: Dominique LecoqTelephone: 1 - 46 55 36 22
L.M.C.39 Rue des Frères-LumièreBP 2269682 Chassieu CEDEXContact: Patrick MinvielleTelephone: 78 90 26 32
PEJOPLASTCap 18, A59189, Rue D’Aubervilliers75886 Paris CEDEX 18Contact: M. TastetTelephone: 1 - 40 34 58 71
GERMANY
ATS AUTOMATEN-TECHNIKSCHREIERT GmbHAlter Teichweg 6322049 HamburgContact: Andre SchreiertTelephone: 040 - 6918581
ATV AUTOMATENTECHNIKVERTRIEB-und SERVICE GmbHUhlandstrasse 3788255 BaienfurtContact: Günter RohlederTelephone: 0751 - 551717
EWV ELEKTRONOK-WARTUNG-VERTRIEB GmbHDistelweg 989537 Giengen/BrenzContacts: Peter Renner Erich WeimertTelephone: 07322 - 96190
330.PROD.GB.4 : GEN.GEN.OFF_DIST.NONE.NONE.GB.11 Black 54
54 ©, Mars, Inc., 1995.
CashFlow 330 acceptor Product Maintenance Handbook
MECHSHOP (SOUTH)80 Manor RoadWallingtonSurrey SM6 0ABContact: Frank GoldingTelephone: 0181 - 669 - 9483
POWERHOUSE SYSTEMSUnit 20Soho Mill EstateWooburn GreenBucks. HP10 0PFContact: David NindTelephone: 016285 - 31313
QUICKMECHUnit 7/9 Central Park TradingEstateWestinghouse RoadTrafford ParkManchester M17 1PGContact: Neil VaughanTelephone: 0161 - 8487446
GREECE
RADIO KATOUMAS15-19 Praxitelous Street105 62 AthensContact: Spyros KatoumasTelephone: 1 3250412 - 6
HONG KONG
COIN-TECH SERVICES (HK) LTDRoom C1, 12th floorKaiser Estate, Phase 141 Man Yue StreetHunghomKowloonContact: Raymond WongTelephone: 2330 - 2868
HUNGARY
HOKI KFT.Gyepsor U.1H - 1751 Budapest PF:90Contact: Franz HochsteinTelephone: 1 - 2776422
PAYMENT SYSTEMS KFTCziraki ut 26-32H -1163 BudapestContact: George FazakasTelephone: 1 -163 6051
ISRAEL
MARAP AUTOMATICINSTRUMENTS Ltd.5 Ha’arad StreetTel Aviv 69710P.O. Box 43025Contact: Guy AlonTelephone: 3 - 6475613
ITALY
C.V.D.A.Via Marco Polo, 1835020 Albignasego (PD)Contact: Daniele CicognaTelephone: 049 - 685266
ESPERIA DISTRIBUZIONE s.r.l.Via della Misericordia 4520057 Vedano Al Lambro (MI)Contact: Marco PorroTelephone: 039 - 492511
EUROVEND s.n.c.Via Reiss Romoli 13310148 Torino (TO)Contact: Giovanni ConteTelephone: 011 -2202366
330.PROD.GB.4 : GEN.GEN.OFF_DIST.NONE.NONE.GB.11 Black 55
©, Mars, Inc., 1995. 55
CashFlow 330 acceptor Product Maintenance Handbook
V.M.V. S.r.l.Via dell’Artigianato, 2037047 S. Bonifacio (VR)Contact: Marco MionTelephone: 045 - 7665686
MEXICO
R.R. REFRIGERATION S.AGustavo Baz 387Naucalpan53160 EdoDe MexicoContact: Arturo Ruiz CastanedaTelephone: 393 - 34 - 22
NETHERLANDS
EPSTransportweg 282421 LS NieuwkoopContact: Jan DoelmanTelephone: 1725 - 79315
NEW ZEALAND
CASH HANDLING SYSTEMS LTDMDC Building, Level 2142, BroadwayNewmarketAucklandContact: Mark OliverTelephone: 09 - 522 - 2204
NORWAY (also Iceland)
ELEKTRONISKE BETALINGSSYSTEMER a.s.Skiveien 4Postboks 502N 1411 KolbotnContact: Svein Atle StorvandTelephone: 66 - 80 - 5020
POLAND
T. HAUUl Goworowska 2PL- 03-353 WarszawaContact: Tomasz HauTelephone: 22 - 112541
PORTUGAL
EQUISISTEMAS LDAPraca Joao Do Rio 9 - 3ESQ1000 LisbonContact: Artur BorgesTelephone: 1 - 8460925/6/7
SINGAPORE
COIN TECH SERVICES(SINGAPORE) PTE LTDBlock 998Toa Payoh North4 -12/14 Singapore 318993Contact: Yeo Yang PengTelephone: 65 - 356053
SLOVAKIA
PRODIGI CORP.Drobného 2784402 BratislavaContact: Gabriel BajkaiTelephone: 7 - 786 757
SOUTH AFRICA
ELECTRONIC VENDINGSERVICESP.O. Box 13924, Chrisoliet StreetJukskei Park2153Contact: Chris DrewnickiTelephone: 11 - 7042383
330.PROD.GB.4 : GEN.GEN.OFF_DIST.NONE.NONE.GB.11 Black 56
56 ©, Mars, Inc., 1995.
CashFlow 330 acceptor Product Maintenance Handbook
SOUTH KOREA
HEE SUNG TRADING CO LTD10 - 36 Jamwon - dongSeocho - kuSeoulContact: C.I. KimTelephone: 2 - 515 5696
SPAIN
TRATECNICA S.A.c/ Gonzalas Dávila, 20-2 0plantaPoligono Industrial De Vaffecas28031 MadridTelephone:91 - 3802200(Approved Service Centre)
SWEDEN
4 S ELECTRONICS A.BBox 52018425 AkersbergaContact: Leif OdellTelephone: 08 - 540 - 66040
SWITZERLAND
KONTROLL-SYSTEMEOergelackerstrasse 4CH-8707 Uetikon am SeeContact: Walter NeuhausTelephone: 1 - 9206262
TAIWAN
COIN-TECH (S) PTE LTD98 Sec. 2, Cheng-teh RoadTaipeiContact: Jerry ChangTelephone: 2 - 5574748
THAILAND
COIN TECH LTD2571S01 87, Ladprow RoadWangtonglhangBangkapiBangkok 10310Contact: Pracha TechakaroonTelephone: 2 - 932 - 2609
TURKEY
ÜÇEL ELEKTROTEKNIK ISLERISanayi ve Ticaret Limited SirketiSelçuklar Sok No: 6Akatlar 80630IstanbulContact: Faruk CengicTelephone: 212 - 2575656
330.PROD.GB.4 : 330.PROD.GB.4.IX Black 57
©, Mars, Inc., 1995. 57
CashFlow 330 acceptor Product Maintenance Handbook
AAccept And Reject Options 47
Accept Gate Module 2, 41, 42, 47Acceptor Module 10, 11, 19, 43Accessories And Spares 45Applications Support 24BBack Cover 2, 8, 40, 41, 43, 46CChannel Adaptor 39, 45Channel Mounting 5, 6, 7, 45Cleaning 19Coin Outputs - Negative Common 35Coin Outputs - Positive Common 35Compatibility 2, 26, 48, 49Configuration 9, 10DDiscrimination PCB 26Discriminator Module 2, 40Discriminator Spring 42Disposal Of Product 1EElectrical Interfaces 21Electrical Specification 21, 23, 29, 30, 33,
34, 36, 37, 38Enable Teach 10, 11Enable Teach Mode 21Environmental Performance 1FFault Finding 8, 20Flight Deck 42Flight Deck Lid 8, 42HHost Intelligent Interface 21, 24, 25IInhibit Teach 10, 11Inhibit Teach Mode 21Initialising 8, 44Installation 3, 4, 5, 6, 7Interface PCB 2, 10, 11
330.PROD.GB.4 : 330.PROD.GB.4.IX Black 58
58 ©, Mars, Inc., 1995.
CashFlow 330 acceptor Product Maintenance Handbook
LLocal Expansion Interface 24MMachine Interface PCB 10, 26, 27, 28, 31,
35, 43, 44Man Machine Interface (MMI) 10, 11, 26MARS ELECTRONICS INTERNATIONAL 50Mars® Route Alpha 250 Terminal 10, 12Maxi Front Plate 4MEI DISTRIBUTORS 51Midi Front Plate 3Mini Front Plate 3Module Replacement 39, 40, 41, 42, 43,
44OOperating Voltages 1PParallel Interface 9PCB Connector 27, 28, 31, 32, 36,
37PCB Cover 2, 11, 40, 44Power Down 10Power Up 10, 11Product Overview 2RReject Lever 8, 11Remote Reject Unit 6Retaining Clip 39Route Inhibit Connector 29SSafety 1, 11Serial Interface 2, 9, 26Shorting Link Connector 28, 29Specific Coinsets 9Support Tools 25TTerminal Addresses 16Terminal Key Functions 13, 14, 15Test 5, 6, 7, 11Time-Out 10, 19
330.PROD.GB.4 : GEN.PROD.BPAGE.NONE.NONE.GB.1 Black,White 59
™
REPRESENTATIVE:
®
UNITED STATES
1301 Wilson DriveWest ChesterPa 19380Telephone: 610- 4302500Facsimile: 610- 4302694
GREAT BRITAIN
Eskdale RoadWinnersh TriangleWokinghamBerkshire, RG41 5AQTelephone: 01734- 697700Facsimile: 01734- 446412
SWITZERLAND
Ch. Pont-du-Centenaire 109Plan-les-OuatesP.O. Box 26501211 Geneva 2Telephone: 22- 8840505Facsimile: 22- 8840504
FRANCE
Boulevard Des ChenatsBP 745550 St. Denis de L’hotelTelephone: 38 - 59 - 6534Facsimile: 38 - 59 - 6172
GERMANY
Industriering 17 A41751 ViersenTelephone: 02162- 9560Facsimile: 02162- 41544
ITALY
27011 Belgioioso (Pv)Viale Dante, 40Telephone: 0382- 979313Facsimile: 0382- 970790
SPAIN
M.a De Molina, 40-3a
28006 MadridTelephone: 91- 3379182Facsimile: 91- 5635517
AUSTRALIA
302 Parramatta RoadAuburnNew South Wales, 2144Telephone: 02- 737- 5390Facsimile: 02- 737- 5399
JAPANMars Electronics International3f Masushi-kosugi Tower Place403 Kosugimachi 1-chomeNakahara-kuKawasaki-shiKanagawa-ken 211Telephone: 44 - 712 - 1315Facsimile: 44 - 712 - 1439
CANADAMars Electronics International37, Holland DriveBoltonOntario, L7E 5S4Telephone: 416 239 2782Facsimile: 416 239 3322