PRODUCT DATA SHEET 1st September 2016                      Side 1 af 2 

 90RH adhesive

Description Dispersion based adhesive Usage ege 90RH adhesive is a floor adhesive for bonding on

concrete. Suitable for various types of textile floor coverings. Product performance - Wet bonding

- Short assembly time - Good working conditions - Used on absorbent surfaces - Fulfils the German emission class Emicode EC 1 PLUS

TEKNISKE DATA Basic Vinylacetat copolymer Solvent Water Solids App. 72 % Density App. 1400 kg/m3 Consistency Flexible tixotrop Colour Creamewhite Ready to use Full strenght after 3 days Withstands normal load immediately after installation Assembly time 0 – 20 min Optimal conditions +150 C - +250 C and ca. 65 % RH Temperature resistance -30OC - +70OC

PRODUCT DATA SHEET 1st September 2016  Side 2 af 2 

 90RH adhesive INSTRUCTIONS

Humidity conditions

Pretreatment

Tools

Material consumption

Installation

Requirements

Cleaning instructions

Shelf life

Max. humidity 90% RH. Humidity at a temperature in the substrate at +15 ° C - +25 ° C according to Floor Gulvfakta section 2.11 and 2.12. Should the temperature of the floor after commissioning (eg by heating) be modified, the humidity must be measured at this temperature.

The subfloor must be clean, dry and leveled, leveled to ± 2 mm measured with a 2 m straightedge. The temperature in the room must according to Gulvfakta section 2.14 be +20 ° C and humidity between 35% RH - 75% RH. If the humidity is too high, it can be reduced by heating and ventilation.

Toothed trowel

Textile floor coverings 300 – 550 g/m2.

On absorbent surfaces the carpet is installed after a short delay and within 20 min. in order to achieve full pass to the backing. The carpet is rubbed firmly into the adhesive so that all air bubbles disappear. After approx. 1 hour rubbing/drum rolling of the carpet. Non-absorbent surfaces must be levelled before installation.

Installation / waiting time depends on the current temperature and humidity. The above times are stated on the basis of laboratory tests at 180 C and 65% RH. Therefore, the times given as a guideline only.

Good cleanliness should be observed. Avoid skin and eye contact. Glue on the skin is removed with soap and water or hand cleaner. Tools are cleaned with water before the glue dry. Dried up adhesive can be removed mechanically.

12 months in tightly closed container.

SAFTEY Kodeno. (1993): 00-1Fire classification NonHealth class Non desiccating Further information in our Safety Data Sheet.

This product meets with the guidelines for the criteria of use listed reverse. The company is ordinary member of the GEV.

OM 010 July 29, 2016 valid until July 29, 2021

Licence Number: 7221/24.02.97

For the product Ege 90 RH adhesive

Due to application date July 29, 2016 With reference to the classification in accordance with the directives as stipulated in § 10 of the GEV trademark constitution on behalf of the GEV for the above mentioned product as per § 5, section 4 of the GEV trademark constitution is awarded the licence for the use of the GEV trademark

Trade name(s):

valid until:118443 14.01.2023

0736

2018

Signed:

Date: 17.01.2018

Name: Dr. Michael Zieger

Position: Head of Product Safety and Compliance

EUROPEAN COMMUNITIES DECLARATION OF CONFORMITY

issued in accordance with the

MARINE EQUIPMENT DIRECTIVE (MED) 2014/90/EU

Module B: EC Type Examination Certificate:

This is to certify that in compliance with the Council Directive 2014/90/EU of 23 July 2014 on marine equipment, last amended by Commission Directive 2015/559/EU and Commission Implementing Regulation (EU) 2017/306, the company:

Dieselstrasse 3

declares that the following product(s) is/are conforming to types as described in the EC-Type Examination Certificates from the Notified Body BG Verkehr (Ship Safety Division) (EC Registration No. 0736).

UZIN Utz AG

D-89079 Ulm - Germany

Module D, Quality Certificate No. SEE 15088 valid until 27.10.2018

Standards applicable: IMO Res. MSC.307(88)-(FTP Code 2010)

A Technical Construction File for this equipment is retained at the following address:

ege 90 RH Adhesive

MED/3.18e - Surface materials and floor coverings with low flame-spread characteristics (adhesives used in the construction of "A", "B" & "C" class divisions)

The mark of conformity is affixed to the label of the packed material(s) including the Identification Number of the Notified Body:

UZIN Utz AG

D-89079 Ulm - GermanyDieselstrasse 3

Annex 1, Part 5

MED Item No & Item designation:

Declaration of Conformity 1 / 1

Requirement guidelines for the awarding of the EMICODE licence

The flooring installation material mentioned in the front side licence has to meet with the following criteria in accordance with the constitution and guidelines of the Technical Advisory Board of the GEV and others:

• The product meets all the legal requirements, especially the chemical law and its specifications.

• The product is solvent free due to occupational health. Only in case of a wood flooring coating it might contain low content of solvents.

• A safety data sheet (MSDS) according to local law in its respectively valid version is to be established for the product.

• Carcinogenic, mutagenic, reprotoxic substances as well as those substances under suspicion to cause such defects are not permitted to be used in the manufacturing of this product.

• The testing of the product is in accordance with the defined GEV test method. Afterwards the definition of VOC is conducted in a test chamber by using the Tenax thermodesorption procedures with GC/MS analysis.

• The classification into the EMICODE classes is performed according to the following listed and described criteria and TVOC concentration groups. For product labelling the matching EMICODE class is to be used.

GEV product matrix

EMICODE

EC 1PLUS

EC 1 EC 2

TVOC/TSVOC28d in µg/m³

1. Liquid products

After 3 days

< 750 TVOC;

after 28 days

< 60 TVOC /

< 40 TSVOC

After 3 days

< 1000 TVOC;

after 28 days

< 100 TVOC /

< 50 TSVOC

After 3 days

< 3000 TVOC;

after 28 days

< 300 TVOC /

< 100 TSVOC

1.1 Primers (floor and wall)

1.2 Ready to use thin fixations and adhesives

1.3 Damp proof primers or barrier primers

1.4 Liquid sealants, pasty surface sealants

2. Mineral products

2.1 Cement and calcium sulphate based levelling compounds

2.2 Cement based and other mineral tile mortars and joint fillers

2.3 Waterproofing slurries

2.4 Screeds and screed binding materials

3. Pasty products with high content of organic binder

3.1 Pasty adhesives for floor coverings and parquet, ready-to-use adhesive for ceramic tiles, other adhesives

3.2 Pasty fixations for floor coverings

3.3 Levelling compounds (based on dispersion or reactive resin)

3.4 Powder based adhesives with high content of organic binder

4. Ready to use products which do not require chemical curing or physical drying

4.1 Underlays

4.2 Insulating underlays

4.3 Self-adhesive tapes and underlays

4.4 Installation boards, decoupling/insulation boards, wall panels

5. Joint sealants, joint insulations, joint sealing tapes

5.1 Joint sealants (based on dispersion or reactive resins), repair fillers

5.2 Joint insulations, expanding foams

5.3 Pre-compressed or foam plastic joint sealing tapes

5.4 Sealing membranes, tapes, sleeves for small surfaces

5.5 Sealing membranes for large surfaces

6. Surface coating for wood floorings < 100 Σ TVVOC,

TVOC, TSVOC

thereof max. 40 SVOC

< 150 Σ TVVOC,

TVOC, TSVOC

thereof max. 50 SVOC

< 450 Σ TVVOC,

TVOC, TSVOC

thereof max. 100 SVOC

6.1 Waterborne wood floor coatings

6.2 Water-based joint filler for parquet

After 3 days < 750 TVOC; after 28 days < 60 TVOC /

< 40 TSVOC

After 3 days < 1000 TVOC; after 28 days < 100 TVOC /

< 50 TSVOC

After 3 days < 3000 TVOC; after 28 days < 300 TVOC /

< 100 TSVOC

Edition: April 3, 2014 * TVOC = Total Volatile Organic Compounds