product catalog...takes seconds to inject. no injection hose or caulk gun needed. concentrated...

Air Conditioning, Refrigeration & Heating

Quality Products for

PRODUCT CATALOG

Permanent Seal

Compatible with All Refrigerants & Oils

Easiest to Install

READY

SET

SEAL!

Takes seconds to inject.

No injection hose or caulk gun needed.

Concentrated formula means less material in the system.

Table of Contents

Total System Protection 1-3

Coil Cleaners and Sprayers 4-10

Indoor Air Quality 11-14

Gas Leak Detectors 15

Refrigeration Oil & Vacuum Pump Oil 16-17

Aerosol Products 18-20

Specialty Products 21-22

Insulation Products 23

Glycol & Closed Systems 24-25

Water Treatment & Plumbing Products 26-30

Water Filtration Maintenance 31

Water Filtration 32-33

Nu-Plus by Everpure 34-39

Training Classes 40

Visit us at www.nucalgon.com or call 1-800-554-5499 1

A/C EasyDryThis product is a quick and simple way to prevent and eliminate moisture in a system. A/C EasyDry contains a dehydrating agent that converts system moisture into a natural organic material that is compatible with and mixes with the lubricant. It is great for preventing acid formation, which is caused by moisture in a system, and it works with all refrigerants (except ammonia). Each can will treat up to a 5 ton system and is easily installed with the reusable piercing valve and hose.

3 ounce pressurized can 4051-06 A/C Piercing Valve and Hose 4051-99

A/C EasySeal®A/C EasySeal prevents and seals refrigerant leaks in residential and light commercial ACR systems. It is perfect for those hard-to-find and expensive-to-fix leaks and works with all refrigerants (except ammonia). It is easily installed with the reusable piercing valve and hose. A/C EasySeal circulates with the system’s refrigerant, and if a leak should occur, it will quickly and permanently seal the leak and prevent the system from losing refrigerant and shutting down.

A/C EasySeal 3 ounce pressurized can - treats 1.5 to 5 ton systems 4050-06 A/C EasySeal-SS 1.25 ounce pressurized can - treats fractional to 1.5 ton systems 4050-01 “2+1” Display Pack 2 cans of A/C EasySeal and an A/C Piercing Valve and Hose 4050-02 A/C EasySeal-XL Treats systems with refrigerant charge of 125 lbs. – 250 lbs. 4050-10A/C Piercing Valve and Hose 4051-99

Total System Protection Total System P

rotection

EasySeal® Direct InjectEasySeal Direct Inject is a new generation of sealants. Its innovative injection method makes it easier to install than other sealants. With this new injection system, pumping down the unit is a thing of the past. EasySeal Direct Inject works with all refrigerants and oils. Concentrated formula means less material in system. It is perfect for split systems, heat pumps, microchannel coils, packaged units, and mini splits. EasySeal Direct Inject is formulated to not plug cap tubes or expansion valves.

EasySeal Direct Inject 4050-08EasySeal Direct Inject bulk 6-pack 4050-07EasySeal-SS Direct Inject 4050-05

The Next Generation of Refrigerant Leak Sealant


2

Rx11-flush®Rx11-flush is a unique solvent engineered specifically for flushing refrigeration and air conditioning systems. Rx11-flush is ozone-safe, non-toxic, and non-flammable. Used exactly like the old R-11 flushing process, its patented HFC-based solvent formulation is powerful enough to flush away sludge, carbon residues, oils, acids, water and other particulates. Rx11-flush is ideal for system flushing after burnouts, during retrofits and for flushing line sets for R-410A conversions. Rx11-flush has been the industry’s standard for over a decade, and contractors agree — it’s the best flush for R-410A retrofits and after compressor burnouts.

Rx11-flush Starter Kit Contains a 1 lb. canister, Rx11-flush Gun and Hose, and Injection Valve 4300-081 lb. canister Recommended for a 3-4 ton system 4300-09"2+1" Display Pack Contains one Injection Valve and two 2 lb. canisters 4300-102 lb. canister Recommended for a 5-7 ton system 4300-1113 lb. canister Recommended for up to 50 ton system 4300-1526 lb. canister Recommended for systems over 50 tons 4300-26

Rx11-flush® Liquid Rx11-flush Liquid is a new and improved chemistry that is the next generation in flushing technology. It remains a constant boiling solvent, and its stronger, faster- acting formula dissolves more oil, moisture and contaminants than any other flush. It is ideal for line sets, burnouts, and other flushing requirements.

19.5 ounce can 4300-30 Rx11-flush Liquid Starter Kit 4300-38

Total System Protection

Endorsed by York®, Goodman®, Nordyne®, Coleman®, and Daikin®

Tota

l Sys

tem

Pro

tect

ion

Rx11-flush® AccessoriesThe Rx11-flush product family also includes various support tools. This includes the Injection Valve for hooking up to a charging hose for flushing and the Flushing Tool for facilitating line set flushing. In addition, the Rx11-flush Gun with a built-in flushing attachment and the Rx11-flush Hose (24˝) are available.

Flushing Tool 4300-50Rx11-flush Gun 4300-51Rx11-flush Hose (24˝) 4300-52Injection Valve 4300-89 (Injection Valve fits Pneu-flush® and pressurized Rx-Acid Scavenger® as well)


Total System P

rotectionTotal System Protection

Phase III® Refrigeration Oil Acid Test KitFormulated for use with POEs as well as mineral oils and alkylbenzene, Phase III is an inexpensive, disposable test kit that provides proof-positive that acid level in refrigeration oil is either safe or unsafe. Phase separation makes it easy to see change in color of acid indicator (even if a leak detection dye has been added to the oil). Just two bottles to work with, it is simple, safe, accurate, and small enough that you can carry several in your tool box.

1 each 4320-W8

1. Pour the solution from the small bottle into the large bottle. The bottom layer of this mixture will be purple.

2. Completely fill the small bottle with oil from the unit being tested. Do this immediately after the oil is removed from the crankcase, since exposure to air will contaminate the oil and give a false test result.

3. Pour the oil into the large bottle and shake well.

4. Wait two to three minutes. A phase separation will develop as the oil rises to the top of the mixture and an aqueous layer forms on the bottom.

5. If the bottom layer: Stays purple- the oil is satisfactory. Turns light pink or loses color completely- the oil has higher than acceptable acid content.

Good Oil Bad Oil

How to Test Oil with Phase III®

A/C Re-New®A/C Re-New is a highly formulated, OEM approved product that has established an outstanding track record enhancing the performance of air conditioning and refrigeration systems. A/C Re-New frees sticky valves, quiets noisy compressors, reduces energy consumption by lowering starting and running amps, and improves heat transfer in the evaporator and condenser. It’s great for new systems as a preventative or to reinstate performance of older systems.

(Injection Valve fits Rx11-flush® and Pneu-flush® as well)

Rx-Acid Scavenger®The most effective way to neutralize or “scavenge” acid in refrigeration and air conditioning systems. It is perfect for use after burnouts or during normal on-going system maintenance. In addition, Rx-Acid Scavenger can be used with all lubricants: mineral, alkylbenzene and polyol ester. Now available in a pressurized can for easy injection into charged systems or hermetically sealed systems.

2 fluid ounce unpressurized bottle 4301-023.8 ounce pressurized can 4301-05 Injection Valve 4300-89

1 quart can 4057-54 4 fluid ounce can 4057-55A/C Re-New Injector Tool 4057-99

EQUIPMENT USED ON

Condenser Coils • • • • • • • • •

Mini-Split Condenser Coils • • • • •

Small Condenser Coils • • • • • • • • •

Evaporator Coils • • • •

Mini-Split Evaporator Coils • • •

Small Evaporator Coils • • • •

Microchannel Coils • • • • •

Electronic Air Filters •

Fan Blades, Permanent Filters • • • • • •

FORMULATED TO REMOVE

Greasy Dirt & Oil • • • • • • • • •

Cooking Grease • • • • • •

Lint, Dust, Dirt & Grime • • • • • • • • •

Tobacco Tars •

Oxide (Corrosion) Deposits • • • •

Cottonwood/ Bugs • • • • •

FEATURES & BENEFITS

Product Type Alkaline Alkaline Alkaline Acidic Alkaline Alkaline Alkaline Alkaline Alkaline

Foaming • • • • • •

Brightening • • • • •

Degreasing • • • • • • • • • • •

EPA Registered Disinfectant

No Rinse (Evaporators) • • •

No Rinse (Condensers) •

Biodegradable • • • • • • • • • •

USDA Authorized • • • •

U.S. EPA’s Safer Choice Program

NSF Registered • • • • • •

Aerosol Liquid

* * *

Aerosol Liquid

4

Coil

Cle

aner

Sel

ecti

on G

uid

e

Nu-Solve™ NRCal-Brite® Special HD CalClean®Foam-Brite® Alka-Brite® Plus CalClean® TriClean™ 2xTri-Pow’r® HDNu-Brite®

Nu-Calgon Coil CleanersFound on Pages 6-7

Coil Cleaner Selection Guide

* Dilution ratios for no rinse applications: Tri-Pow’r HD = 10:1, Liquid CalClean = 10:1 (Aerosol CalClean must be rinsed), Special HD CalClean = 40:1, Green Clean = 10:1

EQUIPMENT USED ON

Condenser Coils • • • •

Mini-Split Condenser Coils • • • •

Small Condenser Coils • • • •

Evaporator Coils • • • • • • •

Mini-Split Evaporator Coils • • • • • • •

Small Evaporator Coils • • • • • • •

Microchannel Coils • • • • • • • • •

Electronic Air Filters

Fan Blades, Permanent Filters • • • • • • •

FORMULATED TO REMOVE

Greasy Dirt & Oil • • • • • • •

Cooking Grease • •

Lint, Dust, Dirt & Grime • • • • • • • • •

Tobacco Tars

Oxide (Corrosion) Deposits

Cottonwood/ Bugs

FEATURES & BENEFITS

Product Type Alkaline Alkaline Alkaline Alkaline Alkaline Alkaline Alkaline Solvent Alkaline

Foaming • • • •

Brightening

Degreasing • • •

EPA Registered Disinfectant • • •

No Rinse (Evaporators) • • • • • • • •

No Rinse (Condensers) •

Biodegradable • • • • • • • • •

USDA Authorized •

U.S. EPA’s Safer Choice Program • • •

NSF Registered • •

*

Aerosol Liquid


Coil Cleaner Selection

Gu

ide

Evap-Fresh® No Rinse

Nu-Blast® &Cal-Blast®Blackhawk®Evap-Green™Cal-Green™Evap-Powl’r®-C Evap-Foam® Green Clean

Coil Cleaner Selection Guide

CompleteCare Mini-Split Kit

Nu-Calgon Coil CleanersFound on Pages 7-9

6

Nu-Brite®Nu-Brite is the most effective coil cleaner available today. It foams, brightens, and is an equally effective yet safer alternative to HF acid-based products. It produces a high volume of foam that cleans more effectively than acids, particularly in removing grease. Biodegradable. The liquid versions are USDA approved and NSF registered.

18 ounce can 4291-181 gallon bottle 4291-082.5 gallon pail 4291-05*55 gallon drum 4291-01

Foam-Brite®The ultimate in foaming alkaline cleaners, Foam-Brite cleans and brightens while at the same time providing tremendous foaming to push dirt and grime out of the coil. Can easily be used in place of the more dangerous HF acid-based products. Biodegradable. NSF registered.

1 gallon bottle 4178-082.5 gallon pail 4178-05*55 gallon drum 4178-01

Alka-Brite® PlusA non-acid, alkaline based product for brightening and cleaning air-cooled condensers, Alka-Brite Plus contains the best available detergents to quickly penetrate and remove oxidation. Its foaming action helps to lift greasy soils out of the coil. Biodegradable. NSF registered.


Coil

Cle

aner

s

Cal-Brite® Cal-Brite is a low pH cleaner developed for cleaning evaporator coils, air-cooled condensers and other finned cooling and heating coils. Its versatility is based upon glycolic acid and other unique ingredients. It provides moderate foaming and brightening and is safe for use indoors as well as outdoors. It’s particularly suitable when lime scale must be removed from outdoor coils.

1 gallon bottle 4133-08 55 gallon drum 4133-01

Coil Cleaners

* A 2.5 gallon pail wrench is also available. Part Number ZE64.


Coil Cleaners

Coil Cleaners

CalClean® An alkaline detergent formulated for cleaning evaporator coils, air-cooled condenser coils, metal filters, fan blades, and other surfaces soiled with grease, dust and dirt. Biodegradable. USDA approved. Aerosol is NSF registered. Also great for microchannel coils.

20 ounce can 4081-75 1 gallon bottle 4135-082.5 gallon pail 4135-06*55 gallon drum 4135-01

Tri-Pow’r® HD An outstanding general purpose coil cleaner, providing detergency and degreasing as well as deodorizing capability. Its positive emulsion technology is very effective against oily grime as it converts the deposits into a more fluid or liquid form that can be easily rinsed away. It is non-acid, non-toxic, and biodegradable. NSF registered. Also great for microchannel coils.

1 gallon bottle 4371-88 55 gallon drum 4371-81

TriClean 2x™ The new way to clean a condenser coil. Simply connect to hose, clean, and rinse. TriClean 2x is metal-safe, designed for rapid emulsion of soils from the coil. Restores efficiency and is ideal for painted fin and microchannel coils. Eliminates the need for a sprayer.

1 quart sprayer with hose connector 4372-24

Nu-Solve™ NRReady-to-use, non-rinse condenser coil cleaner for situations with limited water availability for rinsing. Nu-Solve NR is also for other applications where it is desirable to have less diluted cleaning solution on a commercial roof or when a solvent-based aerosol approach is not practical. Nu-Solve NR effectively emulsifies dirt and grime and provides a benefit of leaving a protective treatment on the aluminum for added corrosion protection, making the next cleaning easier. Nu-Solve NR can be applied with Nu-Calgon's poly sprayer or the Nu-Solve NR Sprayer (page 10).

1 gallon bottle 4295-08

Special HD CalClean® The best non-foaming cleaner available. Specifically formulated to remove tobacco tars from electronic air cleaners as well as the most stubborn deposits from finned coils. USDA approved. Also great for microchannel coils.

1 gallon bottle 4143-08 2.5 gallon pail 4143-06*55 gallon drum 4143-01

* A 2.5 gallon pail wrench is also available. Part Number ZE64.


Evap Pow’r®-C A no-rinse product formulated for cleaning evaporator coils. It is metal-safe, and it cleans and emulsifies even the most stubborn soils and deposits. Biodegradable. USDA approved. Also great for microchannel coils.

8

Coil

Cle

aner

s Coil Cleaners

Evap-Fresh® No Rinse Evaporator Coil Cleaner & DisinfectantEvap-Fresh is a ready-to-use, no-rinse cleaner and disinfectant for evaporator coils. It effectively cleans as well as kills mold and bacteria. This one-step no-rinse disinfectant cleaner is perfect for air conditioners, commercial air handling units, HVAC cooling coils, refrigeration equipment, and evaporator coils. EPA registered specifically for use on HVAC equipment.

18 ounce can 4166-751 gallon bottle 4166-08

Green CleanA pleasantly scented, all-purpose, environmentally friendly cleaner designed for the rapid removal of grease and other heavy soils. It can be used right out of the bottle or diluted for milder jobs. Biodegradable. Also great for microchannel coils.

1 quart spray bottle 4186-241 gallon bottle 4186-0855 gallon drum 4186-01

Cal-Green™ Condenser CleanerCal-Green is a plant-based, natural condenser cleaner that is powerful enough to remove dirt, grease, and grime. It meets the U.S. EPA Safer Choice Program standards, making it a safer choice for the user and the environment. This non-foaming, non-toxic concentrate is perfect for cleaning residential or commercial systems and restores their efficiency while being environmentally responsible. Also OEM approved for microchannel coils.

1 gallon bottle 4190-0855 gallon drum 4190-01

1 gallon bottle 4191-0855 gallon drum 4191-01

Evap-Green™ Evaporator CleanerEvap-Green is a no-rinse product that is perfect for numerous heating and air conditioning applications, such as evaporator coils, roof top units, window units, metal filters, fan blades, and more. Evap-Green meet the U.S. EPA Safer Choice Program standards, making it a safer choice for the user and the environment . Evap-Green is also biodegradable and will not harm plants, animals, and aquatic life. Metal-safe — meets OEM guidelines for all aluminum coils, including microchannel types.

The following products are part of Nu-Calgon’s Environmentally Friendly Green Select line. These coil cleaners meet the U.S. EPA Safer Choice Program standards, making them a safer choice for the user and the environment.

Evap Foam No Rinse®Evap Foam No Rinse is a high-performing, heavy-duty detergent. It is formulated with special surfactants and alkaline cleaners that have been developed into a foaming, no-rinse product. Evap Foam is ideal for use on most coils, but it is particularly suited for use on cooling or evaporator coils. The aerosol can be sprayed either right side up or upside down. NSF registered. Can be used with Talon Flexible Aerosol Wand (4776-0) for hard to reach locations (see page 18).

18 ounce can 4171-75


Coil Cleaners

Cal-Shield®Cal-Shield is a synergistic liquid formulation based upon DuPont’s Teflon® fluoro-additives. It’s designed for application on air-cooled condensers, evaporator coils, and other finned heating and cooling coils. Cal-Shield will shield and protect the coil from adverse conditions.

1 quart spray bottle 4148-321 gallon bottle 4148-08

Coil Cleaners

Nu-Blast®A no-rinse condenser coil cleaner in a convenient aerosol package. Double action of high-pressure blast and solvent cleaning restores design efficiency of condenser coils. It is non-flammable and non-conductive. No rinse required — cleaning solvent evaporates completely. Use with adequate ventilation.


Cal-Blast® Cal-Blast is a no-rinse condenser cleaner that will powerfully separate undesirable materials from the surface, offering maximum cleaning of finned coils. It’s a high-performance aerosol with excellent solvency and blasting spray.


Nu-Shield®Nu-Shield, the newest generation of chemistry for protecting coils and other surfaces, is a super-hydrophobic (water repelling) product. The non-conductive formula has numerous applications in the management of water on non-food, non-potable water surfaces for the HVACR trade. Simply spray it on and watch the water bead up and roll right off.

9 ounce can 4294-75

Non-treated : Water Clings

Nu-Shield : Water Repels

Blackhawk®Blackhawk is an expanding foam coil cleaner. Formulated to deeply penetrate the coil, it liquefies to quickly remove grease, grime, or oily soils from deep within the coil. Blackhawk’s formulation is safe and problem-free for cleaning evaporator or condenser coils in an occupied building; produces no objectional fumes. It is particularly effective on coils on refrigerators, coolers, and freezers located in restaurants and other commercial establishments. NSF registered. Can be used with Talon Flexible Aerosol Wand (4776-0) for hard to reach locations (see page 18).


Coil Protectants

DuraCoil DuraCoil is a long-lasting coating for coils and surfaces in corrosive environments. It uses a durable, OEM-approved Heresite® Coating. DuraCoil has a fast, air-dry formula that bonds to all metals and causes negligible heat transfer loss across the coil. Great for repairing an OEM-approved coil coating that has been compromised while in service! Brown in color.


NEW

10

Spra

yers Sprayers

Rep

lace

men

t p

arts

are

ava

ilab

le f

or

all N

u-C

alg

on

sp

raye

rs. C

on

tact

you

r lo

cal w

ho

lesa

ler.

Coil Gun®A “hose-end” sprayer that features five different mix ratio settings designed for coil cleaners. Utilizes a 2 quart capacity bottle and includes a foam wand as well as “quick disconnect” capability. The Coil Gun Probe accessory has a 90º direction of spray that allows cleaning from inside the coil. It also provides easy access in tough-to-reach locations.

Coil Mate™ Coil Cleaning HoseDurable 5/8 inch diameter reinforced hose with Flex-Guard protection. The 50-foot hose is equipped with solid brass wrench fittings. The Coil Mate is a necessity when using the popular Coil Gun® or rinsing an air-cooled coil with water after using a Nu-Calgon coil cleaner.

No. 50P Poly SprayerThe No. 50P is constructed of high-density translucent polyethylene. It has a half gallon (3 pint) capacity. The nozzle is adjustable and the flow rate is controlled by a thumb lever. It comes with a 7˝ polyethylene pump.

No. 100P Poly SprayerThis sprayer is constructed of high-density translucent polyethylene. It has a funnel top for easy chemical pouring and a 1 gallon working capacity. It comes with a 8˝ polypropylene pump, brass handle and extension tube with adjustable nozzle, a wear-resistant hose, and a pressure relief valve.

No. 200P HiPressure Poly SprayerThe No. 200P HiPressure Poly Sprayer is constructed of high-density translucent polyethylene. It has a 2 gallon working capacity, funnel top, pump handle, and all-brass hardware. No pumping is required. Pressurize the sprayer with water through a “quick disconnect” fitting.

No. 220CP Poly SprayerThe No. 220CP Poly Sprayer is constructed of high-density translucent polyethylene with a funnel top that provides easy chemical pouring. This 2 gallon capacity sprayer features an easy fill level indicator and comes with an 8˝ pump and a high resin plastic adjustable nozzle with three feet of hose.

No. 300P Poly SprayerThe No. 300P Poly Sprayer is constructed of high-density translucent polyethylene. It has a funnel top and a 3.5 gallon capacity (3 gallon working capacity). It comes with a 10˝ Celcon pump, brass extension tube with adjustable nozzle, and five feet of vinyl hose.

Coil Mate 61231Hot Water Hose 61238Plastic Pistol Grip Nozzle 61241

1 each 4770-0 1 each 4770-2 1 each 4771-2

1 each 4771-3 1 each 4772-0

Multi-Purpose SprayerA 24 ounce capacity sprayer. It is ideal for small cleaning jobs, such as window units and water coolers.

1 each 4768-W3

Coil Gun 4774-0Coil Gun Probe 4774-1

Nu-Solve NR SprayerBackpack-type sprayer developed for applying Nu-Solve NR, a non-rinse outdoor coil cleaner when water availability for rinsing is an issue. Sprayer utilizes a four-gallon tank with no holes or connections at the bottom to leak! Provides high-pressure spray for added cleaning effectiveness, large pressure chamber for lasting pressure, and a flexible and rugged wand with an adjustable spray nozzle.

1 each 4775-0

NEW


Indoor Air Quality Indoor A

ir Qu

ality

Bio-Fresh® FoggerThe Bio-Fresh Fogger is made of a one-piece, seamless heavy-duty copolymer. It uses a 48˝ flexible hose and is adjustable from 0-18 ounces per minute with the respective particle size at 20 to 80 microns. It’s ideal for spraying Bio-Fresh cd in duct work and large areas.

1 each 4693-0

Bio-Fresh® cdA ready-to-use bacteriostatic, fungistatic, and deodorizer based upon chlorine dioxide technology. Inhibits the growth of bacteria, mold, mildew, fungi, and yeasts in IAQ applications, and it may be applied to occupied spaces. Its EPA registration applies to HVACR ventilating equipment, including coils, condensate pans, filters, and duct-work. Easily applied by spraying, brushing, sponging, or wiping. EPA registered.


Evap-Fresh® No Rinse Evaporator Coil Cleaner & DisinfectantEvap-Fresh is a ready-to-use, no-rinse cleaner and disinfectant for evaporator coils. It effectively cleans as well as kills mold and bacteria. This one-step no-rinse disinfectant cleaner is perfect for air conditioners, commercial air handling units, HVAC cooling coils, refrigeration equipment, and evaporator coils. EPA registered specifically for use on HVAC equipment to kill H1N1 and other viruses such as Norwalk, Rhoto, Hepatitis, Rabies MRSA, and more.

18 ounce can 4166-751 gallon bottle 4166-08

1 each 4151-08

CompleteCare Mini-Split KitThe CompleteCare Mini-Split Kit cleans, disinfects, and deodorizes mini-splits, as well as controls mold and mildew. It also protects condensate pans and lines from plugging. Each kit treats 2-3 mini-splits. Contains one 18 oz. can of Evap-Fresh No Rinse and one PurCool® Green Mini Strip.

A/C Drain Sucker®A/C condensate drain pan overflow is caused by slime and sludge that builds up and clogs the drain line. The A/C Drain Sucker quickly removes the clog and the excess water, resolving the overflow problem. The kit includes a PurCool® Pan Strip to provide months of preventive treatment and free flowing drains, as well as all fittings and hoses for suction or pressure applications.

Nu-Calgon Number ClenAir NumberA/C Drain Sucker kit 61308 CADS1PurCool Pan Strip - treats 3 tons - 6 mos. 61043 1903D

Drain SolveIdeal for condensate pan drains. Drain Solve saves time and money with its ease of use. It eliminates application concerns associated with more reactive, fuming drain openers. Simply pour it down the drain and let it work without fear of noxious fumes or reactions. Does not contain sulfuric acid.

1 quart 4165-241 gallon 4165-08

12

Indo

or A

ir Q

ual

ity

The Original ClenAir™ Odor NeutralizerClenAir’s unique odor neutralizing formula removes odors quickly and permanently. It is a true odor eliminator, not a mask. Originally designed for use in central air systems, on fire and flood restoration jobs and in sewage facilities, ClenAir is a professional product, yet it leaves no lingering antiseptic or perfume smell. It is great for odors caused by fuel oil, smoke, pets, mold and mildew, cigarette and cigar smoke, decay, cleaning solvents and even skunks. ClenAir has three different scents: Original, CherryAir, and OrangeAir. The scents come in multiple sizes for multiple applications.

CherryAir Nu-Calgon ClenAir

Mini Tub 61018 CA1800M1/2 lb. Tub display box 61010 1800D1 lb. Tub 61011 1801

Original Nu-Calgon ClenAir

Mini Tub 61000 CA1500M1/2 lb. Tub display box 61001 1500D1/2 lb. Tub 61002 15001 lb. Tub 61003 15013 lb. Tub 61004 1503

OrangeAir Nu-Calgon ClenAir

Mini Tub 61028 CA1300M1/2 lb. Tub display box 61020 CA1300D1 lb. Tub 61021 CA1301

Original Nu-Calgon ClenAir

10 lb. Tub 61005 151030 lb. Tub 61006 1530Wall Unit (White) 61007 1300Gel Brick for Wall Unit (1lb.) 61008 1401

CherryAir Nu-Calgon ClenAir

3 lb. Tub 61013 180310 lb. Tub 61015 181030 lb. Tub 61017 1830

OrangeAir Nu-Calgon ClenAir

3 lb. Tub 61023 CA130310 lb. Tub 61025 CA131030 lb. Tub 61027 CA1330

Indoor Air Quality: ClenAir by Nu-Calgon

ClenAir Liquid FormulaClenAir Liquid is a fast acting deodorizing product. It eliminates odors via an oxidation process while leaving a fresh scent. Applications include HVACR equipment, such as evaporator coils, duct work, condensate pans, refrigeration cases, reach-ins, and walk-in boxes. It can also be poured down drains, garbage disposals, and in trash cans. Spray in restrooms, locker rooms and on fouled carpeting and upholstery. Used by hospitals, nursing homes, and HVACR technicians.

Nu-Calgon ClenAir

Unscented Spray 16 oz. 61030 1600DUnscented Liquid 1 gal. 61031 1610Citrus Spray 16 oz. 61033 1700D

Nu-Calgon ClenAir

Citrus Liquid 1 gal 61035 1710CherryAir Spray 16 oz. 61037 1900DCherryAir Liquid 1 gal. 61038 1910

HVAC Odor Block®ClenAir HVAC Odor Block is not a perfume mask or cover-up. The unique ClenAir formula molecularly reacts with the airborne odor-causing compounds and eliminates them and other indoor pollutants, leaving clean, fresh, air behind. The HVAC Odor Block makes it easy to remove odors and improve the indoor air quality in the entire home or building by treating the air through the HVAC system. Use in A/C units, furnaces, rooftop units, fan coil units, and air handlers. Part numbers 61060 and 61061 last up to 3 months. The HVAC Odor Block XL (61070) lasts up to 6 months.

Nu-Calgon Number ClenAir NumberResidential HVAC Odor Block 61060 1502Residential HVAC Odor Block XL 61070Commercial HVAC Odor Block 61061 CA1015

Side Vent for Carbon Filtration


Indoor A

ir Qu

ality

Gel Tabs - Condensate Drain Pan TreatmentFormulated with a breakthrough technology for treating air conditioning drain pans and lines. Keeps the drain pan from clogging and eliminates foul and musty odors. When activated by condensation, the tablet will turn to gel and lock into place. Dissolves continuously and completely with nothing left to remove for up to three months. Stack together to increase duration.

3 ton tab (12 in tube) 4185-033 ton tab bulk (200) 4185-04 5 ton tab (6 in tube) 4185-05

5 ton tab bulk (100) 4185-0615 ton tab (1 each) 4185-15 20 ton tab (1 each) 4185-20

NEW

5 (up to 5 tons) 4295-345 Slim (up to 5 tons) 4295-36

PanPadsA product formulated to eliminate the build-up of bacteria and slime growths in air conditioning and refrigeration condensate drain pans. In laboratory tests, it has been proven effective against a wide spectrum of harmful bacteria, including Legionella. The product is EPA registered for this application. NSF registered.

15 (up to 15 tons) 4296-2445 (up to 45 tons) 4296-45

Indoor Air Quality

1 bottle (200 tablets) 4296-60

Pan-Treat®Pan-Treat condensate tablets control odors and prevent overflows caused by plugged condensate drain lines. They can also be used in humidifiers. They are very easy to use, as well as non-corrosive, non-toxic, and biodegradable.

PurCool® StripsPurCool Strips keep A/C and refrigeration condensate drain pans clean and free flowing. Use PurCool Strips to prevent condensate drain clogs, costly overflows, and corrosion. Just place them anywhere in the drain pan where the PurCool Strip will contact the condensate water and enjoy up to six months of economical protection. PurCool Strips will adhere to the drain pan and will not float or move. Dissolves completely, leaving no residue. Safe for metal and plastic drain pans.

Nu-Calgon ClenAir

3 ton strip 61043 1903D3 ton strip bulk (100) 61047 1903D-1005 ton strip 61042 2001D

Nu-Calgon ClenAir

10 ton strip 61041 2003D30 ton strip 61040 2009

14

Indo

or A

ir Q

ual

ity Indoor Air Quality: ClenAir by Nu-Calgon

PurCool® Green Strips and TabletsPurCool Strips/Tablets prevent slime, sludge, odors, and overflow of condensate pans. Time release formula adheres to pan and fully dissolves over time. PurCool Green Strips/Tablets use plant-based suspending and dispersing action to keep drain pans clean and free flowing. Products are available for commercial, residential, and mini split applications. Sizes are based on system tonnage, with each strip/tablet lasting up to six months.

Nu-Calgon Number ClenAir NumberPurCool Green Mini Strip 61044 PCG5MSPurCool Green Commercial Strip 10 ton 61045 PCG10TPurCool Green Commercial Strip 30 ton 61046 PCG30TPurCool Green 3 ton tablet 61048PurCool Green 3 ton bulk (200) 61049PurCool Green 5 ton tablet 61051 PCG5TPurCool Green 5 ton bulk (100) 61052 PCG5T-100

PurCool® TabletsPurCool Tablets utilize a powerful formulation to keep condensate drain pans clean and free flowing. Use PurCool Tablets to remove sludge and slime in A/C condensate pans to prevent costly water damage caused by overflows. They will control clogs, build-up, odors, and corrosion in drain pans, condensate pumps, and humidifiers.

HVAC Carbon Block® In-Duct Air Purification SystemHVAC Carbon Block is an add-on carbon purifier for all HVAC systems. Improves indoor air quality by removing odors, indoor air pollutants, and VOCs. Treats up to 10 tons for up to nine months.

Nu-Calgon Number ClenAir NumberHVAC Carbon Block 61062 CACB10

Humidifier Panel™ ReplacementsClenAir Universal Humidifier Panels provide optimum moisture output, performance, and durability. They replace Aprilaire, Honeywell, Carrier, Bryant, Lennox, ICP, and others. Ultra Upgrade Humidifier Panels' material retains water, increasing moisture output and reducing water waste by up to 50%. They replace Aprilaire, Honeywell, Carrier, Bryant, Lennox, ICP, and others.

Nu-Calgon Number ClenAir NumberUniversal Humidifier Panel - #10 size 61250 CA10Universal Humidifier Panel - #12 size 61251 CA12Universal Humidifier Panel - #35 size 61252 CA35Ultra Upgrade Humidifier Panel - #10 size 61254 CA10UPUltra Upgrade Humidifier Panel - #35 size 61255 CA35UP

Spacegard® Filter Media ReplacementsThese Merv 11 filter media are direct replacements for the Aprilaire Spacegard 201 and 401. Merv 11 media removes pollen, allergens, smoke, dust, dust mites, bacteria, spores, and pet dander. The large filter surface area provides for low resistance and longer filter life, more than 6 months!

Nu-Calgon Number ClenAir NumberReplacement for Aprilaire Spacegard 201 61256 CA201Replacement for Aprilaire Spacegard 401 61257 CA401

*Aprilaire and Spacegard are registered trademarks of Research Products Corporation

Nu-Calgon Number ClenAir Number1 bottle (200 tablets) 61053 PC200


Gas Leak DetectorThe original industry leak detector. A high viscosity liquid that forms bubbles when daubed on a gas leak. Non-corrosive, non-staining, and harmless to skin. Detects any type of gas leak, such as air, compressed air, carbon dioxide, nitrogen, natural gas, and refrigerant gases. Freeze protection to -20˚F. Six ounce plastic bottles have dauber in cap. USDA approved.

6 ounce bottle with dauber 4180-53

Gas Leak Detectors

8 ounce bottle with dauber 4184-531 quart spray bottle 4184-241 gallon bottle 4184-08

Fluorescent Gas Leak DetectorA fluorescent formulation that provides improved visibility and long lasting bubbles. It is non-corrosive to metals and is freeze protected to 5˚F. Suitable for high and low temperature applications. Can be used for most refrigerants, natural gas and oxygen systems. USDA approved.

Gas L

eak Detectors

6 ounce bottle with dauber 4182-531 quart spray bottle 4182-241 gallon bottle 4182-08

Cal-Blue® LT Gas Leak DetectorThe same high quality formulation as regular Cal-Blue Plus, but it has added freeze protection to -20˚F. It is the ideal detector for geographical areas that may experience very cold temperatures. The longest lasting bubbles in the industry! NSF registered.


AccuTrak® Ultrasonic Leak DetectorModel VPE - Now with touchprobe included. Patented technology detects the ultrasonic sound of a leak!

Nu-Calgon Number ClenAir NumberAccuTrak® Ultrasonic Leak Detector 61307 CAVPE

Cal-Blue® Plus Gas Leak DetectorCal-Blue Plus is a complete gas leak detector with freeze protection to 5˚F. Its high viscosity formula enables it to remain in contact with the applied surface for an extended period of time, allowing it to detect the smallest of leaks. The longest lasting bubbles in the industry! It is also non-corrosive to metal, and it will not affect ultraviolet or black lights. NSF registered.

16

Emkarate RL Viscosity 1 Quart 1 Gallon 5 Gallon 53 Gallon22H 100 SUS 4313-4632H 150 SUS 4314-44 4314-46 4314-45 4314-41

32HB 150 SUS 4314-6232-3MAF 150 SUS 4314-64 4314-66 4314-65 4314-67

46H 200 SUS 4315-46 4315-4168H 300 SUS 4316-44 4316-46 4316-45 4316-41

68HB 300 SUS 4316-86 4316-8568HP 300 SUS 4316-76 4316-71100E 500 SUS 4317-66100H 500 SUS 4317-46170H 850 SUS 4318-26 4318-25 4318-21

220H+ 1100 SUS 4318-66 4318-65 4318-61220XL 1100 SUS 4318-75

Polyol Ester (POE) Lubricant

Emkarate® RL LubricantThe Emkarate family of polyol ester refrigeration lubricants are designed specifically for use with HFC refrigerants. They are available in a range of viscosities. They have excellent thermal and chemical stability, and they are compatible with a wide range of elastomers, polymeric materials, and other materials of construction. Fully miscible and compatible with mineral oils and alkylbenzene lubricants as well as with CFCs, HCFCs and HFCs.

Polyvinyl Ether (PVE) Lubricant

Idemitsu Polyvinyl Ether LubricantPVE lubricants provide for increased stability and lubrication. They do not hydrolyze in the presence of moisture, a very important feature in HVACR applications. Additionally, they are compatible with other refrigeration oils and process fluids. PVE lubricants also exhibit compatibility and performance with frequently used anti-wear additives.

Idemitsu Viscosity 1 QuartFVC32D 32 SUS 4319-14FVC68D 68 SUS 4319-24

C-3s, C-4s, C-5s Refrigeration OilThese are mineral naphthenic lubricants manufactured by Calumet Lubricant Company and available in three viscosities. They are specifically designed for today’s high performance air conditioning and refrigeration compressors using CFC and HCFC refrigerants. These compressors run at higher speeds and generate higher temperatures, and as a result, they require better lubrication. Use of these oils will ensure continued efficient operation.

Nu-Calgon Viscosity 1 Gallon 5 Gallon 55 GallonC-3s 150 SUS 4303-07 4303-05 4303-01C-4s 300 SUS 4304-07 4304-05 4304-01C-5s 500 SUS 4305-07 4305-01

Mineral Oil

Ref

rige

rati

on O

il &

Vac

uu

m P

um

p O

il


Refrigeration

Oil &

Vacu

um

Pu

mp O

ilAlkylbenzene Oil

Zerol Viscosity 1 Gallon 5 Gallon 55 Gallon150 150 SUS 4310-07 4310-01

200TD 200 SUS 4308-07 4308-01300 300 SUS 4311-07 4311-05 4311-01

400CA 400 SUS 4311-65500 500 SUS 4312-05

Zerol® Alkylbenzene Refrigeration OilZerol Refrigeration Oil is recommended for use in all refrigeration and air conditioning applications using CFC and HCFC refrigerants. It is highly recommended by refrigerant and compressor manufacturers for use with R-22 and other HCFC blends such as R-409A as it provides many distinct advantages: excellent miscibility, excellent thermal stability, and low temperature performance compatibility with mineral oils. It is the oil of choice for R-22 and R-502.

Oil RefractometerA precision optical instrument that allows for the rapid and accurate determination of the refractive index of oil solutions. It will specifically assist in determining the percent of residual oil remaining in a refrigeration system when converting it to a new refrigeration oil. Such retrofits require converting the mineral oil to a polyol ester (POE) or polyalkylene glycol (PAG), an alkylbenzene lubricant (Zerol®) to a POE, or a mineral oil to an alkylbenzene.

1 each 4815-0

Total Lube Refrigeration Oil Test KitHave a professional lab analyze the oil to help detect potential problems such as metal wear or burnouts. The analysis will provide information on the oil’s moisture, total acid number, viscosity, color, and spectrochemical analysis on 20 plus metals and compounds. Help prevent potential downtime, burnouts, and costly oil changes by incorporating regular testing of the refrigeration oil.

1 each 4996-0

CanVerter®A hand-held pump used to remove or add oil to hermetic compressors. Easy to use; each stroke pumps 1 ounce of oil.

1 each 4814-0

Refrigeration Oil Products

Vacuum Pump OilNu-Calgon’s Vacuum Pump Oil is a quality, high-grade lubricant that performs at the deepest vacuum. It has a very low vapor pressure, and it has excellent lubricity for complete surface protection. It contains no additives or detergents.

1 pint bottle 4383-341 quart bottle 4383-241 gallon bottle 4383-07

Vacuum Pump Oil

Refrigeration Oil Charging PumpAn oil pump for charging refrigeration oil into a system, even while it’s running. This pump can be used for 1 gallon, 2.5 gallon, and 5 gallon containers. Incorporates an automatic bleed valve that keeps pressure equalized inside the container and includes a tapered rubber adapter that fits all container openings without the need for additional adaptors.

1 each 4814-40

18

Aerosol Coil CleanersA

eros

ol P

rodu

cts

Evap-Fresh® No RinseEvap-Fresh is a ready-to-use, no-rinse cleaner and disinfectant for evaporator coils. It effectively cleans as well as kills mold and bacteria. This one-step no-rinse disinfectant cleaner is perfect for air conditioners, commercial air handling units, HVAC cooling coils, refrigeration equipment, and evaporator coils. EPA registered specifically for use on HVAC equipment.

Nu-Blast®A no-rinse condenser coil cleaner in a convenient aerosol package. Double action of high-pressure blast and solvent cleaning restores design efficiency of condenser coils. It is non-flammable and non-conductive. No rinse required — cleaning solvent evaporates completely. Use with adequate ventilation.

Nu-Brite®Nu-Brite is a very effective degreaser and cleaner on condenser coils. Its high foaming characteristic will help push soil deposits out of the coil, leaving it clean and bright. With proper ventilation, it can also be used as a kitchen degreaser by emulsifying stubborn, resistive grease deposits found on coils located in kitchens. Product should be used where adequate rinsing is possible.




Cal-Blast® Cal-Blast is a no-rinse condenser cleaner that will powerfully separate undesirable materials from the surface, offering maximum cleaning of finned coils. It’s a high-performance aerosol with excellent solvency and blasting spray.


CalClean® CalClean is a heavy-duty detergent formulation of surfactants, grease solvents, alkaline cleaners, corrosion inhibitors, and water conditioners. Ideal for cleaning window units as well as small evaporator coils, air-cooled condenser coils, metal filters, fan blades and other surfaces soiled with greasy dust and dirt. NSF registered.


Blackhawk®Blackhawk is an expanding foam coil cleaner. Formulated to deeply penetrate the coil, it liquefies to quickly remove grease, grime, or oily soils from deep within the coil. Blackhawk’s formulation is safe and problem-free for cleaning evaporator or condenser coils in an occupied building; produces no objectional fumes. It is particularly effective on coils on refrigerators, coolers, and freezers located in restaurants and other commercial establishments. NSF registered. Can be used with the Talon Flexible Aerosol Wand (4776-0) for hard to reach locations.


Evap Foam No Rinse®Evap Foam No Rinse is a high-performing, heavy-duty detergent. It is formulated with special surfactants and alkaline cleaners that have been developed into a foaming, no-rinse product. Evap Foam is ideal for use on most coils, but it is particularly suited for use on cooling or evaporator coils. The aerosol can be sprayed either right side up or upside down. NSF registered. Can be used with the Talon Flexible Aerosol Wand (4776-0) for hard to reach locations.


TalonFlexible aerosol wand for Nu-Calgon’s Evap Foam No Rinse, Blackhawk or PenetrateHD products. Provides focused cleaner spray or penetrant in tough-to-reach locations. The Talon is highly flexible, retains shape memory, and provides 27 inches of added length to an aerosol canister for navigating in tight quarters inside the equipment. The reusable Talon is a must-have service tool!

1 each 4776-0

NEW


Aerosol P

roducts

Aerosol Specialty Products

Nu-Shield®Nu-Shield, the newest generation of chemistry for protecting coils and other surfaces, is a super-hydrophobic (water repelling) product. The non-conductive formula has numerous applications in the management of water on non-food, non-potable water surfaces for the HVACR trade. Simply spray it on and watch the water bead up and roll right off.

9 ounce can 4294-75

Break-n-Lube™This advanced technology 4-in-1 product is made with CERFLON® for high performance in a non-drying penetrating lubricant. It’s highly versatile with the ability to penetrate, lubricate, displace moisture, and provide superior resistance to corrosion. It’s specially formulated to help free rusted parts and assemblies.


Food-Grade SiliconeFood Grade Silicone sprays a perfect non-stick surface on ice machine surfaces, vending machines, coin slots, slicing machines, dairy machinery, and other food processing and packaging equipment. An excellent lubricant that prevents binding and sticking. Contains ingredients approved by the FDA for food contact use. USDA approved.


V-Belt DressingV-Belt Dressing is specially formulated to penetrate and extend modern V-Belt life. It is particularly effective in maintaining V-Belt efficiency and performance under today’s increasing performance requirements. It keeps belts pliable, prevents slippage, and does away with squealing and chattering. USDA approved.


Aerosol Lubricants

PenetrateHD® Super Penetrating LubricantLoosens rusted and frozen metal parts. Frees stuck fan blades, blower shafts, pulleys, rusted nuts and bolts, and any frozen, rusted, or seized metal part. Unique low surface tension formula penetrates into the smallest spaces and breaks and dissolves the bonds of rust and corrosion. Lubricates and protects metals. Dielectric strength 40,000 volts. Can be used with the Talon Flexible Aerosol Wand (4776-0) for hard to reach locations.

12 ounce can 6110517 ounce can 6110612 ounce can - LV* 6110717 ounce can - LV* 61108

* LV = Low VOC for California

A/C Shine® Superior Cleaner / ProtectantA/C Shine is specially formulated to clean and protect the painted metal surfaces of outdoor A/C condensing units. It sprays on and wipes off quickly and easily without water. For use on all outdoor unit painted surfaces.

Nu-Calgon Number ClenAir Number

12 oz. 61118 ACS12

Pan-Spray®Pan-Spray is an effective, easy-to-use waterproof rubberized coating that won’t chip, flake, or peel. It’s ideal for sealing out rust and corrosion as well as repairing leaky condensate pans, cooling towers, swamp coolers, roofing, gutters, and down spouts. Pan Spray is the perfect solution for emergency and permanent repair.

16 ounce can - White 4296-5016 ounce can - Black 4296-51

DuraCoil DuraCoil is a long-lasting coating for coils and surfaces in corrosive environments. It uses a durable, OEM-approved Heresite® Coating. DuraCoil has a fast, air-dry formula that bonds to all metals and causes negligible heat transfer loss across the coil. Great for repairing an OEM-applied coil coating that has been compromised while in service! Brown in color.


NEW

20

Aer

osol

Pro

duct

s

Aerosol Specialty Products

Nu-Kill® II Wasp and Hornet KillerA “quick-kill” spray formulation EPA registered to instantly and effectively kill wasps, hornets, and yellow jackets, from distances up to 20 feet. Nu-Kill II also kills with residual action as wasps and hornets return to a treated nest. The formula is safe in and around electrical equipment, having a dielectric strength of 47,000 volts.

Zinc Rich Cold GalvanizingHighly resistant to nearly all forms of corrosion. Perfect for repairing factory galvanized material damaged in shipment, welding, assembly, etc. Its 95% pure zinc film fuses itself to iron, steel, or aluminum. Blends well with hot-dip coating. Meets or exceeds military specifications MIL-P- 26915A, MIL-T- 26433, MIL-P- 21035, MIL-P-46105 and the Preece Test.

Pipe-Dri®Aerosol insulation that provides a moisture barrier to stop sweating and dripping on refrigeration lines, air conditioning lines, and other cold surfaces. Quickly adheres and dries to a hard waterproof coating. Pipe-Dri makes it possible to insulate hard-to-reach areas.



13.5 ounce can 4292-75

Pump ProtectorWhen corrosion occurs in close-tolerance areas, it can cause the impeller to stick or bind. Pump Protector protects seasonally operated pumps against corrosion during shutdowns by winterizing them. It is safe for all types of water pumps and requires no special rinsing at start-up.

10 ounce can 4299-T8

Electrical Contact CleanerCleans, lubricates, and protects electrical contacts from corrosion, and it is safe on most plastics. Cleaning action quickly removes greases, dust, and oxidation, restoring and maintaining precision and efficiency to the instrument and component. Includes extension tube for pinpointing application. USDA approved.

Degreasing Solvent EFA degreasing solvent, specially formulated for cleaning and degreasing equipment where washing or flushing is not possible. Simply spray on and wipe off. Penetrates quick and deep, loosening and liquefying heavy greases and tar. Non-corrosive and non-staining with a dielectric strength over 26,000 volts.

11 ounce can 4082-0314 ounce can - LV * 4082-04

* LV = Low VOC for California and Canada

14 ounce can 4083-7514 ounce can - LV* 4083-83

* LV = Low VOC for California

Aerosol Adhesives

Spray-n-Bond™A wide web spray adhesive formulated specifically for insulation and duct liner applications. Ideal for porous surfaces, it is waterproof, flexible, transparent, non-staining, and it can be used for both temporary or permanent bonds. Formulated with the environment in mind, it contains no chlorinated solvents or ozone depleters, and it is VOC-compliant in states such as California.


Spray AdhesiveSpray Adhesive is a fast-drying, all-purpose product that provides a strong, water-resistant, flexible bond. It is translucent and does not penetrate or soak material causing bleed-through. Spray Adhesive is excellent for labeling, bonding, splicing and sealing paper, cardboard, cloth, rubber, styrofoam, canvas, leather, wood, and most plastics.



Pneu-flush® A flushing and cleaning system specifically designed for pneumatic control air lines. It utilizes DuPont® Vertrel® XM, a premier ozone-safe HFC cleaning solvent. Pneu-Flush works quickly and easily to clean and purge the compressed air lines in HVAC control and other pneumatic systems.

2 lb. canister 4298-01Injection Valve 4300-89 (Injection Valve fits Rx11-flush® and Pressurized Rx-Acid Scavenger® as well)

Degreasing Solvent EFDegreasing Solvent EF is a volatile solvent, especially formulated to provide effective cleaning and drying and reduce safety hazards. It leaves surfaces clean and oil-free. The thorough cleaning action is superior to ordinary chlorinated solvents.

1 gallon 4162-071 gallon - LV* 4162-17* LV = Low VOC for California

Specialty Products

Quick Seal™ Pipe RepairA permanent knitted fiberglass impregnated tape that is designed for quick, in-the-field repair of leaks for all types of pipes. It can be used on both cold or hot water as well as refrigeration, plumbing, industrial, commercial, and residential applications. It is safe for potable water and is UL listed. ANSI/NSF Standard 61.

2˝ x 3´ wrap 4299-104˝ x 12´ wrap 4299-11

Thermo-Trap paste 11 ounce tube 4371-36Thermo-Trap gel 1 quart spray bottle 4371-32Thermo-Trap gel 4 fluid ounce spray bottle 4371-53

Thermo-Trap®The industry’s original heat absorbing paste designed to isolate heat encountered in soldering, welding, and brazing, thereby preventing damage to nearby heat sensitive controls, or fittings. USDA approved. Biodegradable. Available in paste or gel.

Specialty Produ

cts

Great Wipes Great Wipes Industrial Strength Hand Towels are waterless wipes made specifically for the air conditioning, refrigeration, and plumbing service technician. Each premoistened, heavy duty towel has strong pumice scrubbing power that conveniently cleans anywhere and anytime.

75 count canister 4185-75

Scrubs-In-A-Bucket® HVAC80The original Scrubs — disposable, pumice-performance waterless hand cleaner towels that effectively and quickly clean hands on a wide variety of industrial soils and greases. Each self-dispensing portable canister contains 80 perforated disposable heavy-duty towels and are pre-moistened with the famous Scrubs cleaning formulation. Effective yet gentle to the skin. Use anywhere, anyplace, anytime.

30 count canister 4366-2480 count canister 4366-87

Visible Defects Heat Exchanger Inspection SystemThe Visible Defects Heat Exchanger Inspection System is a complete kit that enables the technician to better evaluate the integrity of a heat exchanger. If a crack exists, the specially formulated fluorescent penetrant visually enhances the crack, allowing the technician to see the defect easier.

Visible Defects kit 4385-00Crack Finder replacement solution 4385-06

22

General Purpose CleanersSp

ecia

lty

Pro

duct

s

Other Specialty Products

Green CleanA pleasantly scented, all-purpose, environmentally friendly cleaner designed for the rapid removal of grease and other heavy soils. It can be used right out of the bottle or diluted for milder jobs. Biodegradable. Also great for microchannel coils.

1 quart spray bottle 4186-241 gallon bottle 4186-0855 gallon drum 4186-01

Spray Nine® Cleaner & DisinfectantSpray Nine is a tough task cleaner and broad spectrum disinfectant. EPA-registered Disinfectant kills harmful germs like HIV-1, Influenza, H1N1, Staphylococcus Aureus, Salmonella Choleraesuis and E. Coli in 45 seconds. Also helps prevent cross contamination. Authorized by USDA for use in federally inspected meat and poultry plants with a C-1 rating.

Nu-Calgon Number ClenAir Number1 gallon 61110 2680132 oz. spray 61113 26832

Grez-Off® Heavy Duty DegreaserGrez-Off works hard so you don’t have to. This heavy-duty answer to heavy-duty grease and grime leaves engines, machinery, asphalt, garage floors and more whistle clean. Biodegradable, non-flammable formula hits hard and fast with less impact on user and environment.

Nu-Calgon Number ClenAir Number1 gallon 61115 CAWW1G

Elite® Performance Windshield Washer Cleaner -20°Elite Performance Windshield Washer is independently tested to provide freeze protection to -20°F. Don’t take chances with generic washer products; only Elite Performance offers certified protection.

Smoke Signal™ Smoke Candles and Smoke PensSmoke Signal generates smoke by chemical reaction, eliminating costly equipment and time to pinpoint leaks. Smoke tests will effectively and inexpensively reveal leaks in heating and air conditioning duct work, furnaces, fire boxes, exhaust fans and smoke detectors. Smoke Pens are also excellent for observing ventilation, air balancing, smoke detectors, drafts, leakage, and air flow. The Smoke Pens come with one pen, six replacement wicks (refills available) and instructions. Smoke Signal items contain no explosive materials.

ClenHands: Orange Smoothie™, Orange Crush™ and Cherry Crush™Premium antimicrobial hand cleaners that quickly dissolve dirt, grease, fuel oil, pipe dope, resin, ink, paint, glue, rubber gasket and tile cements and many other hard-to-remove soils. ClenHands Orange Smoothie is a smooth non-pumice formula, while ClenHands Orange Crush is enhanced with fine-ground American pumice. ClenHands Cherry Crush is a cherry-scented antimicrobial hand cleaner with pumice. For use with or without water.

Nu-Calgon Number ClenAir Number1 gallon 61116 2270132 oz. spray 61117 23732

Nu-Calgon Number ClenAir NumberOrange Crush with Pumice 1 gallon 61201 2201Orange Smoothie Non Pumice 15 ounce 61202 2202Orange Crush with Pumice 15 ounce 61203 2215Cherry Crush with Pumice 15 ounce 61204 2315ClenHands Super Gel 11 ounce 61205 2414

Nu-Calgon Number ClenAir NumberSmoke Candle - 4000 cubic feet of smoke 30 sec. - 1A 61302 CAS30Smoke Candle - 8000 cubic feet of smoke 60 sec. - 2B 61303 CAS60Smoke Candle - 40,000 cubic feet of smoke 2-3 min. - 3C 61304 CAS180Smoke Pen 61305 CASP1Refill Package - 6 wicks 61306 CASP1RW


Perma-Wrap™ Foam Insulation TapeFormulated from the highest quality elastomeric thermal insulation material. Its closed cell construction seals out air and moisture, slowing down heat transfer, and can be used on hot or cold water pipes, chilled water, and refrigerant lines to prevent sweating and condensation. Service temps as low as -20ºF with a high continuous temperature of 160ºF and a high intermittent temperature of 220ºF.

Insulation Products Insu

lation P

roducts2˝ x 1/8˝ x 30´ roll 4218-W3

2˝ x 1/8˝ x 30´ roll - dispenser package

4218-12

Nu-Foam®An expanding polyurethane prepolymer foam used as a sealant and insulating product on openings created for refrigeration, air conditioning and heating tubes or pipes, duct joints, and other areas where unwanted air penetration might occur. Contains no CFCs or any HCFCs and is UL classified and fire retardant.

12 ounce can 4293-0420 ounce can 4293-75

Sealing and Caulking CordsNonstaining sealers formulated to be water-resistant, dust- resistant and white in color.They securely adhere to most surfaces and provide excellent insulation value. They are available in 3/8˝ pre-shaped extruded cords, with serrated release paper.

3/8˝ x 25´ roll 4216-27

Thumb-Tite®Formulated and manufactured for use in many sealing, insulating, and general maintenance applications. Excellent adhesion capability and is non-staining, non-hardening, and unaffected by wide variations in temperature — an excellent thumbing grade. Each box contains two 1-pound bars.

2 lb. box 4216-92

Foam Tape PEInsulation tape providing an economical way to prevent sweating or condensation on air conditioning, refrigeration, chilled water or other cold lines. Also used on hot water lines for insulation against heat loss, and it can be overlapped or the edges can be pressed together.

2˝ x 1/8˝ x 30´ roll 4219-20

Foam-Tite®An economically priced tape formulated from quality thermal insulation material. Closed cell construction and can be used on cold water pipes, chilled water lines and refrigerant lines to prevent sweating and condensation. It can also be used on hot water lines, for better insulation against heat loss. Service temperatures of -15ºF to 160ºF.

2˝ x 1/8˝ x 30´ roll 4219-12

Cork TapeFormulated and manufactured as an insulating material for preventing sweating and condensation on refrigerant lines, cold pipes, and other commercial refrigeration and A/C systems. Serves as an excellent insulator on hot pipes, and can also be used as a gasketing material, a sound-deadening material, and for wrapping valves, tees, and fittings. Service at temps as low as -30ºF, as high as 200ºF and won’t sag up to 350ºF.

2˝ x 1/8˝ x 30´ roll 4217-W3

Cork-Tite®Designed to insulate cold pipes for all kinds of air conditioners in cars, homes, freezers, and refrigerators. Helps stop condensation problems and is ideal for blocking heat gain in cold pipes and preventing heat loss in hot pipes. An effective sound dampening material, it can also be used for gasketing purposes, sticks to dry metals and seals tightly without drying. Flexible and does not shrink or melt within the service temperatures of -20ºF to +200ºF.

2˝ x 1/8˝ x 30´ roll 4217-12

24

Freez-Kontr’l®An expanded family of heat transfer fluids (anti-freeze) based upon non-toxic propylene glycol. All products are fully formulated to provide optimum freeze protection as well as corrosion protection in chilled water, hydronic and other closed systems. Safe to use where contact with potable water is possible. GRAS certified.

• Freez-Kontr’l — provides greater than -60ºF freeze protection and greater than -100ºF burst protection.

• Freez-Kontr’l 95/5 — a fully concentrated (~100%), inhibited propylene glycol product.

• Freez-Kontr’l 35 — formulated with 35% propylene glycol for use as a secondary coolant in supermarket rack applications.

• Freez-Kontr’l FG — a certified USP, food grade propylene glycol product at ~100% concentration. Inhibited. NSF registered.

Propylene Glycol

Burst-Kontr’l® AP-100A specially formulated propylene glycol heat transfer solution for use in boilers having aluminum heat exchangers. It has corrosion inhibitors to protect aluminum, copper, solder, brass, and steel. Provides burst protection to -100ºF and freeze protection to -60ºF.

5 gallon pail 4187-15

Gly

col

Freez-Therm®An inhibited heat transfer fluid and anti-freeze based upon ethylene glycol. It can be used in chilled water, hydronic, and other closed systems for both freeze point suppression and corrosion inhibition. An uninhibited version is also available in drums on special order.

1 gallon bottle 4189-075 gallon pail 4189-0555 gallon drum 4189-01

Ethylene Glycol

Freez-Kontr’l 1 gallon bottle 4188-075 gallon pail 4188-0555 gallon drum 4188-02

Freez-Kontr’l 95/5 5 gallon pail 4188-0655 gallon drum 4188-03

Freez-Kontr’l 35 55 gallon drum 4188-35Freez-Kontr’l FG 55 gallon drum 4188-04

Glycol/Oil Transfer PumpHeavy-duty pump designed to transfer Freez-Kontr’l®, Freez-Therm®, or oil products (up to 1000 sus) from Nu-Calgon supplied 55 gallon drums to their application.

Glycol Equipment

Glycol RefractometerAn accurate and economical tool for ensuring proper levels of glycol treatment in HVAC fluid systems. Removes guess work and prevents wasteful over-treatment. It has metal body with cushioned eyepiece, focus adjustment, and a rubber hand grip. A calibration screwdriver, calibration fluid, a plastic pipette, optical cleaning cloth, and a rugged carrying case are included.

1 each 4817-0

Nu-Calgon Number ClenAir Number1 each 61301 GLY32


Closed Systems &

Steam B

oilersClosed Systems & Steam Boilers

Complete Test KitThe complete test kit for cooling water and boiler water application testing. In addition to pH, this kit also provides tests for obtaining alkalinity, nitrite, hardness, sulfite, and chloride levels.

1 each W017-0

Nitrite Test KitUsed for testing treatment residual of Ty-Ion B20 and Ty-Ion B14A. It is a cerric ammonium nitrate (can) titration method, and it can be used in systems containing glycol. Each drop equals 40 ppm of nitrite.

1 each 4797-0

No. 89A Test KitNo. 89A Test Kit contains tests for determining hardness, pH, chloride and alkalinity, as well as treatment residual tests for Ty-Ion C70, Cal-Treat 233, No. 340 Liquid Scale Inhibitor, and Ty-Ion B20. 1 each 4804-0

Organic Phosphonate Test KitUsed to determine the treatment residual of No. 340 Liquid Scale Inhibitor, Ty-Ion C70, and Cal-Treat 233.

1 each 4798-2

Water Test Kits

Ty-lon® B20A liquid nitrite-borax corrosion inhibitor and dispersant for closed recirculating systems. It combines corrosion inhibitors, a unique copolymer dispersant, and a color indicator to facilitate leak detection, into a complete treatment for hot and chilled water closed systems containing ferrous and non-ferrous metal components.


Ty-lon® B14AAn all-in-one boiler treatment product that controls scale, corrosion, and condensate line corrosion in low pressure, low make-up steam heating boilers where 90% or more of the condensate is returned. It is chromate-free and contains a color indicator for visual determination of treatment residual. Its balanced formulation provides an energy-efficient way of heating.


System CleanerA liquid, heavy-duty industrial alkaline cleaner specifically formulated to emulsify and clean equipment surfaces and pipe fouled by cutting oils, grease, lubricants, corrosion products, and other debris.


Winter Treat®Multi-treatment product for hot water and steam heating boilers and other closed water systems. It emulsifies and cleans away rust and corrosion deposit sludge, as well as inhibits system corrosion, foaming, surging, and lime scale. Typical use is one quart per 25 gallons of water.

1 quart bottle 4390-321 gallon bottle 4390-08

Bacteria Test KitKit contains 10 agar paddle tests that are used to monitor bacterial contamination in cooling tower and evaporative condenser water. Test can be performed in a lab or on site. Each side of the paddle is coated with TTC Agar, material that supports growth of most common bacteria. Regular testing will detect and show when bacteria counts are rising.

1 each 4802-0

Bromine/Chlorine Test KitKit measures free and combined halogen (chlorine, bromine), and it should be used to support treatment with Bromicide Tablets. Residual can be expressed as 0.2 ppm or 0.5 ppm of free halogens. Dropper technique is used.

1 each 4803-0

26

Liquid Scale DissolverA hydrochloric (muriatic) acid formulated to remove calcium scales from cooling towers and other water-cooled equipment. It contains low-foaming corrosion inhibitors and a built-in pH color indicator to let you know when the acid has been neutralized. pH test paper is also included. USDA approved.


Season Start® “Imperial Grade” Scale RemoverA powdered sulfamic acid formulation that contains the best inhibitors available for protecting all metals, including galvanized metal. It is the best and the safest dry acid cleaner available. It contains a built-in pH color indicator to let you know when the acid solution has been neutralized as well as wetting and anti-foaming agents. USDA approved.

10 lb. container 4360-8850 lb. pail 4360-84

Low-Foaming PerformanceTo demonstrate its greater low-foam property, Liquid Scale Dissolver was added to a beaker containing lime scale. A leading competitive liquid product was added to another beaker containing an equal amount of lime scale. See the difference! When cleaning towers and evaporator condensers, low-foam is the preferred approach as high foam is dangerous to both personnel and surroundings.

pH Color IndicatorNu-Calgon’s exclusive “built-in” pH color indicator tells you when to add more acid, and it lets you see when the system is clean. At working strength, the acid cleaning solution is green or light blue. When the acid solution is neutralized and is no longer working, the solution turns purple and more acid must then be added. The system is clean when the green color is retained for 20-45 minutes.

Neutralized Working Strength

Competitive Product with

Dangerous Foam

Nu-Calgon Low-Foaming

Liquid Scale Dissolver

Initial Dosage Recommendation

Tons of Horsepower Liquid Scale Dissolver Eco-Lyme Season Start

10 2 gallons 4 gallons 10 lbs.




Scale Removal

Eco-Lyme®Eco-Lyme is a new chemistry for the HVACR market that provides a unique blend of performance with a desired eco-profile. The product is specially formulated to achieve descaling behavior of competing hydrochloric acid-based chemistry descalers. However, the active ingredient is substantially safer on equipment metals. Eco-Lyme is ideal for stainless steel construction to eliminate potential issues of localized corrosion/pitting caused by repeated use of hydrochloric acid. Eco-Lyme is odorless, making it safer to use in the field. NSF registered.

Wat

er T

reat

men

t

1 gallon bottle 4167-08 5 gallon pail 4167-05 55 gallon drum 4167-01


Water T

reatment

Vital-Flo® Tankless Water Heater Descaler Kit The Vital-Flo Tankless Water Heater Descaler Kit is a complete service tool for descaling tankless water heaters. It consists of a submersible descaler pump, a set of 5-foot long hoses with 3/4˝ female hose threaded assemblies, formulated descaler solution packaged in a lidded 4 gallon chemical resistant container. The solution is also available separately. NSF registered.

To Inhibit Scale Formation

Tons of Refrigeration or Horsepower

Containers of Season Treat

Ty-lon C70 Required per Month

No. 340 Liquid Scale Inhibitor Required per Month

Bleed-off for Most Scale-forming Waters

10 1 1/4 gallon 1/4 gallon 1/8 gpm

30 3 2/3 gallon 1/2 gallon 1/3 gpm

50 5 1 gallon 3/4 gallon 1/2 gpm

100 --- 2 gallons 1 1/2 gallons 1 gpm

120 --- 2 1/2 gallons 2 gallons 1 1/4 gpm

150 --- 3 gallons 2 1/2 gallons 1 1/2 gpm

Scale Prevention

Ty-Ion® C70An all-organic liquid scale, deposit, and corrosion inhibitor for use in open recirculating cooling water systems, evaporative condensers, and air washer systems. This treatment program is particularly effective in preventing scale deposits in systems that utilize make-up water with high scaling potentials.

5 gallon pail 7597-0515 gallon pail 7597-P355 gallon drum 7597-01

Season Treat (6R Micromet®)This patented Micromet® Plate product is contained in a unique flow-through package. The package design makes it simple to treat small cooling towers and evaporative condensers. Simply unwrap the package and place it in the sump. One canister treats up to 10 tons for scale (5 tons for corrosion) for five to six months.

1 canister 4364-88

No. 340 Liquid Scale InhibitorAn extremely concentrated scale inhibitor that is effective in hard, highly alkaline water. It is very stable and does not form any sludge. It is most effective at treatment levels between 10 and 15 parts per million. A constant, accurate feed is accomplished with a Drip Feeder or CMS Feed Pump. USDA approved.


No. 31-TX1 Acid PumpCompact submersible pump designed for circulating strong acids and cleaning solutions. All parts are constructed of acid-resistant materials.

HK-31 Hose KitAn accessory item available for use with the No. 31-TX Acid Pump. Kit includes two 1/2 inch tubing adapters, two 10 foot sections of 1/2 inch clear plastic tubing and three hose clamps.

1 each 4603-0

1 each 4604-0

Feeding Equipment

Water Heater Scale Removal

Vital-Flo kit 4387-01 Vital-Flo descaler solution 4387-02

28

Algae Prevention

To Kill Algae or Slime Growth

Tons of Refrigeration or Horsepower Gallons of No. 85 Algaecide per Month Number of No. 90 Bromicide Tablets for an Average System

10 1/6 gallon 5

30 1/3 gallon 15

50 1/2 gallon 25

90 2/3 gallon 45

Bromicide TabletsA chlorine-bromine donating organic compound in tablet form. It slowly releases powerful oxidizing hypohalous acids, which prevent algae and slime bacteria fouling in open recirculating cooling water systems and evaporative coolers. It also has the capability of breaking up and removing existing biological mass from system surfaces. USDA approved and EPA registered.

50 lb. pail 4109-M9

No. 85 AlgaecideNo. 85 Algaecide is a polymeric, cationic biocide that has been developed for controlling biological growth in equipment. It is an EPA registered product to kill algae, bacteria, and fungi in recirculating water systems, industrial air washing systems, and closed systems.

1 gallon bottle 4108-08

pH-Treat™pH-Treat is an in-line treatment product specifically for the treatment of the acidic nature of the condensate water produced by today’s high efficiency furnaces. Includes fitting kit for easy installation.

1 each 4720-06

Humidi-Pro™Humidi-Pro is designed for humidifiers using up to 25 gallons per day and will inhibit scale for one season. Install Humidi-Pro on the water line that supplies water directly to the humidifier.

1 each 4190-02

Other Water Treatment Products

Wat

er T

reat

men

t Corrosion Prevention

To Control Corrosion

Cal-Treat No. 233 Required per Month Bleed-off for Most Corrosive Waters Capacity of System in Tons of Horsepower

1/3 gallon 1/10 gpm 10

1 gallon 1/4 gpm 30

2 gallons 3/8 gpm 50

3 gallons 1/2 gpm 90

Cal-Treat® No. 233A liquid formulation that is used for controlling severe corrosion in evaporative condensers and cooling tower systems. It is based upon a synergistic formulation of zinc, molybdate, and organic phosphonate. Provides superior corrosion control and inhibits scale accumulation.



Water T

reatmentWater Sample Bottles

The proper way to treat a cooling tower, closed loop system, or ice machine is to have the supply or makeup water tested. Nu-Calgon provides this valuable service for free and will analyze the water and recommend effective treatment. These bottles can also be used to send in glycol samples to test freeze points.

1 each (3 bottles) 4995-0

Evap-Treat®Used in evaporative coolers or “swamp coolers” to prevent scale and corrosion. Place it in the cooler sump and it will last all season long, thereby increasing pad life. Utilizes 6R Micromet®, a slow dissolving polyphosphate.

1 each (coolers up to 6,500 cfm) 4173-041 each (coolers up to 10,000 cfm) 4173-06

Conductivity MeterA handheld conductivity meter with built-in cell and automatic temperature compensation. It has an easy-to-read digital meter (in micromhos, 0-10,000) and dual point calibrations.

1 each 4812-0

No. 215 and No. 1075 Drip FeedersUsed for feeding No. 340 Liquid Scale Inhibitor, Cal-Treat 233, Ty-Ion C70 and No. 85 Algaecide. Calibrated at the factory to ensure accurate feeding. Provides the benefits of continuous treatment for small systems without the high cost usually associated with automatic feeding equipment.

No. 215 Drip Feeder 4669-W3No. 1075 Drip Feeder 4670-W3

No. 20L and No. 100L FeedersSteel tanks suitable for pressures up to 150 psi and temperatures up to 212ºF. Uses 3/4 inch FNPT connections for installing on bypass to any size line. Use No. 20L Feeder for initial charges up to 20 pounds (or 2 gallons). Use No. 100L Feeder for initial charges up to 100 pounds (or 10 gallons). Inlet/outlet strainers not included.

No. 20L Feeder 4628-0No. 100L Feeder 4650-0

Jug HoldersThese should be used when drip feeding any of Nu-Calgon’s liquid water treatment products. Once secured to the cooling tower or evaporative condenser, they will hold the 1 or 5 gallon containers in the proper position.

1 gallon holder 4606-05 gallon holder 4607-0

CMS III and CMS-IV Cooling Tower Monitor SystemFor monitoring conditions in cooling towers and evaporative condensers. Provides subsequent bleed-off and chemical feed. It features a combination monitor and pump engineered into one-piece digital equipment. Complete system includes a solenoid valve.

CMS III 4608-0CMS IV 4608-4

Other Water Treatment Products

30

Plu

mbi

ng

Pro

duct

s Plumbing Products

UrinaKleenKeep urinals free flowing with UrinaKleen. Use it to dissolve urinary salts, mineral scale, and rust deposits which are found in urinals. It also attacks the primary source of odors.

Calci-SolveRemove scale from lines and clear clogged drains easily and effectively with Calci-Solve. The product includes a special inhibitor that coats the inside of the pipes with a protective film, allowing the acid in Calci-Solve to quickly dissolve calcium, magnesium, sodium, lime, rust, and other elements without harming pipes.

1 quart 4134-241 gallon 4134-08

1 quart 4590-241 gallon 4590-08

Drain SolveIdeal for condensate pan drains. Drain Solve saves time and money with its ease of use. It eliminates application concerns associated with more reactive, fuming drain openers. Simply pour it down the drain and let it work without fear of noxious fumes or reactions. Does not contain sulfuric acid.

1 quart 4165-241 gallon 4165-08

Vital-Flo® Tankless Water Heater Descaler KitThe Vital-Flo Tankless Water Heater Descaler Kit is a complete service tool for descaling tankless water heaters. It consists of a submersible descaler pump, a set of 5-foot long hoses with 3/4˝ female hose threaded assemblies, and a formulated descaler solution packaged in a lidded four gallon chemical resistant container. The solution is also available separately. NSF registered.

Vital-Flo kit 4387-01 Vital-Flo descaler solution 4387-02

A/C Drain Sucker®A/C condensate drain pan overflow is caused by slime and sludge that builds up and clogs the drain line. The A/C Drain Sucker quickly removes the clog and the excess water, resolving the overflow problem. The kit includes a PurCool® Pan Strip to provide months of preventive treatment and free flowing drains, as well as all fittings and hoses for suction or pressure applications.

Nu-Calgon Number ClenAir NumberA/C Drain Sucker kit 61308 CADS1PurCool Pan Strip - treats 3 tons - 6 mos. 61043 1903D


Water Filtration - Maintenance Water Filtration

- Mainten

anceLiquid Ice Machine Cleaner

Liquid Ice Machine Cleaner is a food-grade phosphoric acid that is fast acting, yet safe to use. It has been formulated to remove scale deposits from ice machines and coffee urns. It does not give off any harsh fumes or contain chlorine or chlorides that would attack stainless steel. USDA approved. NSF registered.

16 fluid ounce bottle 4211-34

Ice Guard™ PlusIce Guard Plus contains advanced technology to prevent and control slime and other microbial growths in ice machines. The technology utilizes known antimicrobial properties to inhibit micro-organism reproduction that cause slime typically found in ice machines. One unit provides up to 6 months protection in machines producing up to 1200 lbs. of ice per day.

1 each 4209-07

IMS-III Sanitizing ConcentrateIMS-III is an EPA registered sanitizing concentrate formulated to sanitize hard, non-porous surfaces and to eliminate odors and slime growths. No rinsing is required when diluted to 1.6 ounces per gallon. Formulated for general use in ice machines, ice cream dispensing equipment, and other food processing equipment.

Nickel-Safe Ice Machine CleanerThe original Nickel-Safe Ice Machine Cleaner. It is a food-grade citric-phosphoric acid product for removing scale deposits from ice machines having nickel-plated or tin-plated evaporators, and it is acceptable for use in all ice machines containing nickel. It mixes to form a green solution, which makes rinsing easier. USDA approved.

6Rsp Micromet®A slow dissolving phosphate specifically formulated for inhibiting scale in ice machines and other equipment using low volumes of water. It is used in Nu-Calgon scale controlling cartridges and requires replacement once every six months. Typical dosage is 8 ounces per 500 pounds of ice (50 gallons of water) a day.

50 lb. pail 4265-50

8 fluid ounce bottle 4207-471 gallon bottle 4207-08

16 fluid ounce bottle 4287-341 gallon bottle 4287-08

32

Wat

er F

iltr

atio

n

Micro-Plus® & Micro-Carbon 4The complete all-in-one treatment for ice machines, coffee urns and brewers, humidifiers, steamers, etc. The Micro-Plus “in-line” filters contain 6R Micromet® to control scale, high-grade activated carbon for eliminating objectionable tastes and odors, and filter discs to remove silt and sediment down to 20 microns. Available in four sizes with 1/4˝ FPT connections. When properly sized, each filter will last up to six months. The Micro-Carbon 4 is available for removing objectionable tastes and odors.

Micro-Plus 2 4615-W3Micro-Plus 4 4612-W3Micro-Plus 8 4613-Y8Micro-Plus 16 4614-Y8Micro-Carbon 4 4617-24

The CTL SeriesThe CTL Series contains a matching product for the Tri-Liminator Filtration System with specifications that are nearly identical. For example, the CTL’s primary cartridge (C0070) will replace both the K00070 and K00174 cartridges, and it has more scale control ability than either of the Tri-Liminator cartridges. Part numbers are easily crossed over: CTL10 replaces the Tri-L10.

CTL 220 4610-30Prefilter 4621-43Primary cartridge - CG5-20S 9108-27

CFS Filtration SystemA family of replacement cartridges and manifolds designed to service existing CUNO® CFS installations.

A cost-effective water filtration system for food service applications: ice machines, fountain beverages, steam ovens, and drinking water. These systems offer manifold and sanitary quick-change cartridges to fit the existing CUNO CFS brand installations and can also support new filtration installations. Nu-Plus CFS is the reliable choice for water filtration to prevent unwanted troubles caused by sediment, scale, or taste and odor existing in CUNO installations.

Sediment – 5 micron 4623-10Sediment – 5 micron / phosphate 4623-11Carbon Block - .5 micron 4623-12Carbon Block - .5 micron / phosphate 4623-13

Water Filtration

Water Filtration - OEM Replacements

Application Micro-Plus 2 Micro-Plus 4 Micro-Plus 8 Micro-Plus 16 Micro-Carbon 4

Water (per day) 12.5 gallons 25 gallons 50 gallons 100 gallons 50 gallons

Ice (per day) Up to 125 lbs. Up to 250 lbs. Up to 500 lbs. Up to 1000 lbs. ---

Coffee (per week) 25 lbs.(1,250 cups) 50 lbs. (2,500 cups) 100 lbs. (5,000 cups) 200 lbs. (10,000 cups) ---

Single Head 4623-01Twin Head 4623-02Triple Head 4623-03Twin Series 4623-06


Water Filtration

-NP Series

NP Series BracketsSome installations may require two or three NP Series housings to meet more than one specific water-related condition. This custom installation can be accomplished through the use of one of the NP Series multi-housing brackets.

NP48PS 4717-87

6R Micromet® CartridgeThe NP246R Micromet Cartridge contains 1 pound of 6R Micromet, and it fits the NP24DD Housing. The NP486R Cartridge contains 2 pounds of 6R and fits the NP48DD Housing, with 10 micron filtration.

Carbon Block CartridgeThe NP24C Cartridge fits the NP24DD Housing while the NP48C fits the NP48DD. These carbon blocks will remove most objectionable tastes and odors and are rated to remove particulate to 10 microns.

6R Micromet®/Carbon CartridgeA custom cartridge, combining 6R Micromet for scale-control and a carbon block for sediment (10 microns), taste and odor control.

NP Series HousingsThese housings are designed to hold one of the NP Cartridges used to filter water for ice machines, coffee urns, and other beverage equipment. The NP24DD and NP48DD Housings fit specific NP24 or NP48 cartridges for controlling scale, sediment, or objectionable tastes and odors. The NP24DD is equipped with 3/8˝ FPT connections and handles up to 4.0 gpm. The NP48DD is equipped with 1/2˝ FPT connections and can handle flow rates up to 5.0 gpm.

NP24PC 4706-87NP48PC 4716-87

NP24C 4701-87NP48C 4711-87

Sediment CartridgeThe NP24S (5˝) and the NP48S (10˝) are made from FDA-approved polypropylene construction and filter to 5 microns. In addition, the 10˝ and 20˝ versions are available in bulk packaging.

6R Micromet®/Sediment CartridgeAnother custom cartridge within the NP Series, consisting of polypropylene for filtration (5 microns) and phosphate for scale-control.

Two housing brackets NP2BRThree housing brackets NP3BR

NP24DD 4704-24NP48DD 4714-24

NP246R 4705-87NP486R 4715-87

NP24S 4702-87NP48S 4712-8720˝ bulk 4621-43

Problem to Solve Daily Capacities

Cartridge Type Sediment Taste & Odor Scale “24’s” “48’s”

“S” Cartridges 4 1800 lbs. (200 gal.) 3600 lbs. (400 gal.)

“C” Cartridges 4 4 1800 lbs. (200 gal.) 3600 lbs. (400 gal.)

“6R” Cartridges 4 4 900 lbs. (100 gal.) 1800 lbs. (200 gal.)

“PC” Cartridges 4 4 4 600 lbs. (65 gal.) 1200 lbs. (135 gal.)

“PS” Cartridges 4 4 550 lbs. (60 gal.)

Water Filtration - NP Series

34

Wat

er F

iltr

atio

n -

Nu-

Plu

s® b

y E

verp

ure

®

QL3B Single System HeadUsed with any Nu-Plus® E Series filters. Head includes a water shut-off valve with mounting bracket and screws. (3/8˝ NPT)

1 each 4621-07

QC7I Single HeadIdeal for all Nu-Plus® E Series filters. Head includes a shut off, flushing valve, and outlet pressure gauge on a box bracket design. (3/8˝ NPT)

1 each 4621-01

QC7I Twin Parallel HeadDual filter head that is parallel plumbed for two Nu-Plus® E Series filters, either mix or match. Head includes a shut off, flushing valve, and outlet pressure gauge on a box bracket design. (3/4˝ NPT)

1 each 4621-02

QC7I Triple Parallel HeadTriple filter head parallel plumbed for three Nu-Plus® E Series filters. Head includes a shut off, flushing valve, and outlet pressure gauge on a box bracket design. (3/4˝ NPT)

1 each 4621-03

QC7I Quad Parallel HeadQuad filter head parallel plumbed for four Nu-Plus® E Series filters. Head includes a shut off, flushing valve, and outlet pressure gauge on a box bracket design. (3/4˝ NPT)

1 each 4621-04

Heads

*Everpure® is a trademark of Everpure, Inc., Westmont, IL.


Water Filtration

- Nu-Plu

s® by E

verpure

®Systems

Nu-Plus E Series by Everpure Coldrink/Insurice SystemsThe Coldrink/Insurice manifolds can be used with any Nu-Plus by Everpure cartridges. i.e. the MC2 or XC2 for carbonated beverages or i20002 or i40002 for ice machines. Utilizes the systems' existing 10" or 20" pre-filter on a single, twin, triple, or quad manifold. Systems come with the initial EC110 or EC210 pre-filter cartidge. Just purchase the appropriate Nu-Plus by Everpure cartridge for your application.

Nu-Plus E Series by Everpure High Flow CSR Manifold with Prefilter Utilizing the nu-MC2 or the nu-XC2 cartridges, this system provides premium quality water to high flow fountain dispensers, coffee makers and ice machines. New and improved Micro-Pure II media inhibits the growth of bacteria. High Flow CSR reduces chlorine taste and odor and other offensive contaminants that can adversely effect the taste of beverages. Precoat submicron technology reduces dirt and particles as small as 1/2 micron and reduces health contaminants such as cysts. Additionally, the SRX Housing inhibits scale when it is equipped with scale-inhibiting IMF-10 ScaleSticks®.

High Flow CSR Manifold with PrefilterTwin Triple Quad

10˝ 9294-02 9294-03 9294-0420˝ 9294-22 9294-23 9294-24

Kleensteam CT and Kleensteam IIEverpure’s second generation water treatment system for steam applications.Kleensteam is a total system delivering high quality filtered water with scale inhibition as well as deliming capabilities. The dual cartridge design provides enhanced performance for low and high flow capacity steamers and flexibility for expanding to meet future needs. Kleensteam also reduces chlorine-induced corrosion. It’s simple to install, operate, and maintain.

Kleensteam CT 1.67 gpm max. flow 9797-50Kleensteam II 2.5 gpm max. flow 9797-21

MRS-20 Reverse Osmosis SystemComplete mineral reduction water processing system that removes at least 90%+ of all dissolved solids that cause scale build-up. The MRS-20 system removes taste and odor causing contaminants as well as dirt and particles. The two-part design makes installation flexible. It has no moving parts and requires no electrical power. System includes mineral reduction processor, carbon filter cartridge, reverse osmosis cartridge, and storage tank. No monitoring of grains per gallon is necessary.

MRS-20 9797-91

Coldrink/Insurice Manifold with PrefilterSingle Twin Triple Quad

10˝ 9293-01 9293-02 9293-03 9293-0420˝ 9293-21 9293-22 9293-23 9293-24

36

Wat

er F

iltr

atio

n -

Nu-

Plu

s® b

y E

verp

ure

® Cartridges

nu-i20002 and nu-i40002

Reduces water-related ice machine problems caused by dirt, objectionable tastes and odor and scale build-up. Pre-coat submicron filtration reduces particles as small as 1/2 micron along with chlorine and other offensive contaminants. In addition, both cartridges use 6R Micromet®, a highly acclaimed scale inhibitor that inhibits scale build-up caused by dissolved minerals. NSF registered under NSF/ANSI Standards 42 and 53.

• Pre-coat filtration with Micro-Pure® II antibacterial protection• Premier 6R Micromet scale control• Cyst and asbestos fibers reduction• Sanitary quick-change cartridge replacement

nu-MC2 and nu-XC2

Reduces chlorine taste, odor and other offensive contaminants that can adversely affect the taste of fountain beverages. Pre-coat submicron filtration reduces particles as small as 1/2 micron, and it helps retain carbonation in drinks. NSF registered under NSF/ANSI Standards 42 and 53.

• Pre-coat filtration with Micro-Pure® II antibacterial protection• Reduces objectionable tastes and odors• Cyst and asbestos fibers reduction• Sanitary quick-change cartridge replacement

nu-i20002 4621-10Capacity: 9,000 gallons • 750 lbs. for most cubers • 1,500 lbs. for most flakers

nu-i40002 4621-11Capacity: 12,000 gallons • 1,000 lbs. for most cubers • 2,000 lbs. for most flakers

nu-MC2 4621-20

nu-XC2 4621-21

Capacity: 9,000 gallons


BH2 and OCS2 Cartridge• Delivers premium quality water for ice and coffee applications• Designed for applications where the i20002 is too long• Precoat submicron particulate reduction • Inhibits scale formation• Taste and odor reduction• NSF registered under NSF/ANSI standards 42 and 53.

BH2 4621-12

OCS2 9618-07

Capacity: 3,000 gallons or 6,000 pots of coffee • 0.5 gpm max. flow

Capacity: 1,500 gallons or 3,000 pots of coffee • 0.5 gpm max. flow

OW200L and OW4Plus Cartridge• Ideal for office or residential water systems• Unique filter blend uses activated carbon to reduce chlorine taste, odor, and other

offensive contaminants• Reduces lead to below the Federal Action Level of 10 ppb• Precoat submicron technology reduces dirt and particles as small as 1/2 micron• Inhibits scale build-up in water-using appliances• NSF registered under NSF/ANSI standards 42 and 53

OW200L 9619-06

OW4PLUS 9635-06

Capacity: 480 gallons




Water Filtration

- Nu-Plu

s® by E

verpure

®Cartridges

Capacity: 10,000 gallons7CB5 9618-16

4CB5 4621-32Capacity: 6,000 gallons

4CB5, 7CB5, 4CB5-S, and nu-7CB5-S CartridgeCarbon Block filter finely polishes water for high quality beverages and food applications. NSF registered under NSF Standard 42.• Problem-solving cartridge for high particulate or low flow water pressure areas • Taste and odor, chlorine reduction• Particulate reduction to 5 micron• 4CB5-S, and nu-7CB5-S cartridges control scale

nu-7CB5-S 4621-30Capacity: 10,000 gallons

4CB5-S 4621-31Capacity: 6,000 gallons

Capacity: 25,000 gallons7FC5 9693-61

4FC5 9693-21Capacity: 15,000 gallons

4FC5, 7FC5, 4FC5-S, and 7FC5-S CartridgeNew Fiberdyne™ II media with Agion® antimicrobial protection to inhibit potential bacterial growth. Balanced for optimum performance in varying water qualities. Helps retain the drink’s carbonation.• Increased capacity 25,000 gallons• Taste and odor reduction• Particulate reduction• NSF standards 42 and 53

• 2.5 gpm flow rate• 5 micron rating• Scale inhibition (4FC5-S and 7FC5-S)

7FC5-S 9693-71Capacity: 25,000 gallons

4FC5-S 9693-31Capacity: 15,000 gallons

4FC, 7FC, 4FC-S, and 7FC-S CartridgeNew Fiberdyne™ II media with Agion® antimicrobial protection to inhibit potential bacterial growth. Balanced for optimum performance in varying water qualities. Improves the taste of fountain drinks and helps retain the drink’s carbonation.• Taste and odor reduction• Particulate reduction• 2.5 gpm flow rate

• 0.5 micron rating• NSF standards 42 and 53• Scale inhibition (4FC-S, and 7FC-S only)

7FC 9692-61 Capacity: 25,000 gallons

7FC-S 9692-71Capacity: 25,000 gallons

4FC 9692-21Capacity: 15,000 gallons

4FC-S 9692-31Capacity: 15,000 gallons

38

Wat

er F

iltr

atio

n -

Nu-

Plu

s® b

y E

verp

ure

®


7CLM CartridgeReduces chloramines, chlorine taste and odor and other offensive contaminants that can adversely affect the taste of beverages. The cartridge reduces particles down to 1/2 micron and reduces cysts and Giardia. Improves the taste of fountain beverages and helps retain the drink’s carbonation. NSF registered.• Chloramine reduction• Chlorine reduction

• Cyst reduction• Particulate reduction

4SI and 7SI CartridgeSpecially designed for ice machines. This cartridge does not include carbon, which allows for complicance with ASHRAE Standard 188. The cartridge reduces sediment and particulate down to 1/2 micron and reduces cyst and Giardia. The filter allows chlorine to pass through, which helps reduce slime and bacteria growth inside the ice machine and ice bin. Ideal for food service operations where baking of bread and pastries is done on-site.• Scale inhibition• Particulate reduction• Cyst reduction

• 0.5 micron rating• NSF standards 42

Cartridges

7SI 9606-01 Capacity: 25,000 gallons • 3.5 gpm flow rate

7CLM 9693-01 Capacity: 3,600 gallons at 1.7 gpm, 5,500 gallons at 1.33 gpm

4SI 9606-51Capacity: 15,000 gallons • 2.0 gpm flow rate

Nu-Plus® CU and Nu-Plus CU-SThe Nu-Plus E Series CU and CU-S cartridges are replacements that are compatible with the CUNO Series CFS 8000 filter cartridges. Both incorporate a carbon block filter that reduces objectionable tastes and odors as well as chlorine and other contaminates, providing high quality beverage and ice. They also reduce extra fine dirt as small as 5 microns. Additionally, the CU-S provides for the reduction of scale formation.

7SO Softening CartridgeA softening cartridge that reduces scale-forming minerals like calcium and magnesium in hard water situations. It may be used on water having up to 30 grains hardness per gallon, at flow rates of up to 1/2 gallons per minute. It is a sanitary quick change cartridge that makes replacement easy. It should be used with an Everpure fine filter cartridge installed in a series plumbed twin head.

7SO 9607-04Capacity: 2,000 grains • 0.5 gpm max. flow

Nu-Plus CU 4622-20

Nu-Plus CU-S 4622-10

Capacity: 10,000 gallons (37,850 liters) • 1.5 gpm flowReplaces CFS-8112, CFS-8720 & CFS-8812

Capacity: 10,000 gallons (37,850 liters) • 1.5 gpm flowReplaces CFS-8112S,CFS-8720S & CFS-8812S

Replacement Cartridges for CUNO®

*CUNO® is a trademark of 3M. This product is not manufactured, sponsored, or affiliated with 3M.


4JT Flushing/Sanitizing CartridgeThe preferred way to introduce ScaleKleen™ Scale Remover or other sanitizing solutions (IMS-III) into all water-using equipment and vending machines. Fits into existing Everpure heads. Eliminates the need for difficult component disassembly. Easy and convenient to help you clean and maintain equipment. Approved by NAMA.

ScaleKleen™ Scale RemoverRestores equipment to peak operating efficiency by removing scale build-up. Quickly removes limescale from coffee brewers. Ideal for deliming steam and ware washing equipment. Great for office coffee system (OCS) applications. Non-toxic, safe to skin and won’t burn clothing. Sewer system disposable; can be poured down the drain. Use with 4JT Flushing/Sanitizing Cartridge.

Other Filtration Products

1 each 4621-00

SRX Scale Inhibitor FeederA complete system for the control of scale in ice, coffee, steam, and combination applications. It dispenses a controlled amount of HydroBlend™ compound, which provides for a more consistent feed and longer life. The system includes a clear housing and one cartridge

Optional: Wing Bracket for all multiple filter head systems manufactured after 2003: 4621-06

1 each 4621-05

Nu-Plus® 10˝ and 20˝ Coarse PrefiltersA 10˝ and 20˝ clear housing, each including a 10˝ and 20˝ replaceable prefilter cartridge. Filters out larger dirt and rust particles, thereby extending the life of submicron and carbon block filters.

Optional: Wing Bracket for all multiple filter head systems manufactured after 2003: 4621-45

E-10 4621-42E-20 4621-44

Nu-Plus® IMF-7 and IMF-10Ice Machine Feeder Scale inhibition cartridge. The translucent cartridge allows for easy visual monitoring of the product’s usage. The larger IMF-10 will last longer or treat higher volumes of water.

IMF-7 Replacement for AR-X 7˝ Housing 4621-13IMF-10 Replacement for SS-10 Scale Sticks 4621-14

Nu-Plus® EC110 and EC210A 10˝ and 20˝ 10-micron nominal filtration cartridge for filtering out larger dirt and rust particles, extending the life of primary filters. For use in the E-10 and E-20 housings as well as other 10˝ and 20˝ housings.

EC110 (10˝) 4621-41 EC210 (20˝) 4621-43

7 ounce packets (24 per case) 4621-172.2 lb. canister (4 per case) 9798-35

Water Filtration

- Nu-Plu

s® by E

verpure

®

40

Coil Cleaning: The Clean Coil Program is a comprehensive seminar dedicated to the safe and proper procedures to clean evaporator and condenser coils. The program will help determine which cleaning method should be utilized for a particular job based on the type and condition of the unit. NATE Recognition Classes: 1 hour Continuing Education Accreditation

Ice Machine Treatment and Filtration: A complete guide to “Extending the Life of an Ice Machine.” The seminar will answer the questions: why use a filter, what filter should be used, and how to keep the system clean, clear, and running properly. It also addresses all of the water-related problems associated with ice machines. (1.5 hours)

Indoor Air Quality Management: The seminar covers the past, present and future of indoor air quality (IAQ). Topics covered in the session: how poor IAQ impacts a business, common causes of poor IAQ, and how to prevent poor IAQ from occurring. NATE Recognition Classes: 1 hour Continuing Education Accreditation

Nu-Calgon Product Line Review: The seminar provides an overview of all the major products that Nu-Calgon offers. The presentation explores when and where to use certain products, as well as explains how using certain products can save time and money. (2 hours)

Refrigeration Oils: An in-depth look at industry refrigeration oils (Mineral, Alkylbenzene, and POE) and when and where to use them. NATE Recognition Classes: 1.5 hours Continuing Education Accreditation

Total System Protection: A thorough look at why burnouts occur, how to prevent them and the proper way to flush a system once a burnout occurs. The training will include acid testing and acid neutralization. NATE Recognition Classes: 1 hour Continuing Education Accreditation

Water Treatment: This seminar will cover the fundamentals of water treatment for cooling towers, evaporative condensers, boilers, and chillers. NATE Recognition Classes: 1.5 hours Continuing Education Accreditation

Winter Water Treatment: This program focuses on what a system needs prior to the winter season, including a review of ethylene and propylene glycol, the proper treatments for hot/cold closed systems, and low make-up steam systems. (1 hour)

Energy Savings with A/C Re-New: Learn about a revolutionary product for revitalizing and energizing A/C systems. The seminar will explain how A/C Re-New will help reduce energy costs, improve cooling performance and reduce the system noise. (1 hour)

Food Service Products for Ice & Beverage Filtration: A comprehensive look at the problems associated with ice and beverage filtration as well as treatment options to solve these problems. We will cover products for ice makers, coffee brewers, fountain beverage machines, steam ovens, drinking water, and more. (1 hour)

Nu-

Calg

on S

emin

ars

& T

rain

ing

Clas

ses

NATE training now online. Visit us at www.nucalgon.com.

Free Seminars and Training Classes


Serving the United States & Canada with the Finest Direct Factory Sales Force in the HVACR Industry

1. Seattle, WA

2. Northern CA

3. Southern CA

4. Los Angeles, CA

5. San Diego, CA

6. Phoenix, AZ

7. Denver, CO

8. San Antonio, TX

9. Dallas - Fort Worth

10. Houston, TX

11. Kansas City, MO

12. St. Paul - Minneapolis

13. St. Louis, MO

14. Baton Rouge, LA

15. Milwaukee, WI

16. Chicago, IL

17. Indianapolis, IN

18. Columbus, OH

19. Birmingham, AL

20. Atlanta, GA

21. Ocala, FL

22. Tampa, FL

23. Miami, FL

24. Raleigh, NC

25. Richmond, VA

26. Baltimore, MD

27. Philadelphia, PA

28. NYC/New Jersey

29. Syracuse, NY

30. Boston, MA

St. Louis, MO (Hdq.)

Nu-Calgon 2008 Altom Court | St. Louis, MO 63146 phone: 800-554-5499 | fax: 800-221-6302www.nucalgon.com

(416) 3-300 | Calgon is a licensed trade name.

product catalog...takes seconds to inject. no injection hose or caulk gun needed. concentrated...

Documents