procast-step by step
DESCRIPTION
Procast Step By Step GuideTRANSCRIPT
![Page 1: ProCAST-Step by Step](https://reader034.vdocuments.us/reader034/viewer/2022050620/54655f56b4af9f3a3f8b4f1e/html5/thumbnails/1.jpg)
SIMULATION STEPS - Create 3D models
- Mesh
- Precast
- Run
- Viewcast
1. Create 3D models
Optionally, you can use : PRO, UNX, CATIA...
To perform simulation requires three main components
+ Fixed mold
+ castings
+ mobile mold
2.Mesh. Perform detailed mesh in turn drew. The mesh is the most difficult stages of procast When meshing need to pay attention to your product
For example: Your casting edges, or into such 1mm thick. the grid can not be> 1 mm. Because the mesh will fail. But smaller mesh than the machine running slowly. So the grid mesh size depends on how much detail and the ability of your computer.
![Page 2: ProCAST-Step by Step](https://reader034.vdocuments.us/reader034/viewer/2022050620/54655f56b4af9f3a3f8b4f1e/html5/thumbnails/2.jpg)
Mesh lower die
Mesh upper die.
![Page 3: ProCAST-Step by Step](https://reader034.vdocuments.us/reader034/viewer/2022050620/54655f56b4af9f3a3f8b4f1e/html5/thumbnails/3.jpg)
Mesh casting.
Assemble the component on together and conduct mesh volume
![Page 5: ProCAST-Step by Step](https://reader034.vdocuments.us/reader034/viewer/2022050620/54655f56b4af9f3a3f8b4f1e/html5/thumbnails/5.jpg)
2.Precast.
Attached material for molding, casting
---------------------
![Page 6: ProCAST-Step by Step](https://reader034.vdocuments.us/reader034/viewer/2022050620/54655f56b4af9f3a3f8b4f1e/html5/thumbnails/6.jpg)
Determining heat transfer mold casting (interface)
------------------------
![Page 7: ProCAST-Step by Step](https://reader034.vdocuments.us/reader034/viewer/2022050620/54655f56b4af9f3a3f8b4f1e/html5/thumbnails/7.jpg)
Determination of boundary conditions, such as temperature, velocity on heat transfer metal mold environment, temperature cooling system .....
-----------------------------------
![Page 8: ProCAST-Step by Step](https://reader034.vdocuments.us/reader034/viewer/2022050620/54655f56b4af9f3a3f8b4f1e/html5/thumbnails/8.jpg)
Set the gravitational acceleration
------------------
![Page 9: ProCAST-Step by Step](https://reader034.vdocuments.us/reader034/viewer/2022050620/54655f56b4af9f3a3f8b4f1e/html5/thumbnails/9.jpg)
Set initial conditions: initial temperature of the mold, casting .... .. ..
---------------
![Page 10: ProCAST-Step by Step](https://reader034.vdocuments.us/reader034/viewer/2022050620/54655f56b4af9f3a3f8b4f1e/html5/thumbnails/10.jpg)
Set to run the simulation conditions: flow, cycles, stress, or micro-structure
After you finish setting the parameters save it and run
![Page 12: ProCAST-Step by Step](https://reader034.vdocuments.us/reader034/viewer/2022050620/54655f56b4af9f3a3f8b4f1e/html5/thumbnails/12.jpg)
4. viewcast:
The flow and temperature field.
![Page 13: ProCAST-Step by Step](https://reader034.vdocuments.us/reader034/viewer/2022050620/54655f56b4af9f3a3f8b4f1e/html5/thumbnails/13.jpg)
![Page 14: ProCAST-Step by Step](https://reader034.vdocuments.us/reader034/viewer/2022050620/54655f56b4af9f3a3f8b4f1e/html5/thumbnails/14.jpg)
![Page 16: ProCAST-Step by Step](https://reader034.vdocuments.us/reader034/viewer/2022050620/54655f56b4af9f3a3f8b4f1e/html5/thumbnails/16.jpg)
Shrinkage Porosity
------------------------------------------------------------------------------------------------
The only preliminary presentation on how to do.
Parameters of each stage you can refer to help