pressure transducers - stone-automation.com · 2012-11-02 · cannon wk 6-32s/1 g cannon wk 6-32s/2...
TRANSCRIPT
PRESSURE TRANSDUCERSFOR
HIGH TEMPERATURE.
85701 M3 pag. 385707 ME pag. 785713 MN pag. 11
85719 W3 pag. 1585725 WE pag. 1985731 WN pag. 23
PRESSURE TRANSDUCERS FOR HIGH TEMPERATURE
CONTENTS
MELT PRESSURE TRANSDUCERS
mV / V output
TECHNICAL SPECIFICATIONS
Nominal accuracy includingLinearity, Repeatibility, Hysteresis
Resolution
Measurement range
Maximum overpressure
Measurement principle
Supply voltage
Strain gage bridge resistance
Isolation resistance (at 50Vdc)
Full Scale Output (FSO)
Zero balance
Calibration signal
Strain gauge housing compensated tem-perature range
Maximum housing temperature range
Thermal drift in compensated rangeZero/Calibr./Sens.
Diaphragm maximum temperature
Zero drift due to change in processtemperature
Material in contact - Standardwith process medium
Thermocouple (model M32)
Protection degree (with 6-pin mating connector)
Electrical connections
H <±0.25%FSO (100...2000 bar)M <±0.5%FSO (35...2000 bar)
Infinite
0..35 to 0..2000bar0..500 to 0..30000psi
2 x FS 1.5 x FS above1000bar/15000psi
Strain gage Wheatstone bridge
6..12Vdc (10Vdc typical)
350 Ohm(550 Ohm below 100bar - 1500psi)
>1000 MOhm
2.5 mV/V (option 2)3.33 mV/V (option 3)
±5% FSO
80% FSO
0...+100°C32...212°F
-30...+120°C -22...250°F
< 0.02% FSO/°C< 0.01% FSO/°F
400°C 750°F
0.02 bar/°C 15 psi/100°F
15-5 PH with Armoloy coating 17-7 PH corrugated diaphragm withTitanium Nitride coating for ranges
<100 bar (1500psi)
STD : type “J” (isolated junction)
IP65
6-pin Conn. VPT07RA10-6PT(PT02A-10-6P)
8-pin Conn. PC02E-12-8P
FSO = Full Scale Output (output signal at nominal pressure)
Main features
• Pressure ranges from:0-35 to 0-2000 bar / 0-500 to 0-30000 psi
• Strain gage Wheatstone bridge• Accuracy :
<±0.25% FSO (H); <±0.5% FSO (M)• Internally generated 80% calibration signal (R-Cal)• Fluid-filled system for temperature stability • Fully interchangeable with all existing brands• Grade of protection: IP65 (6-pin connector version)• 1/2-20UNF , M18x1.5 standard threads ; other types
available on request• Standard diaphragm is 15-5 PH stainless steel with
Armoloy coating • 17-7 PH corrugated diaphragm with TiN coating
(Titanium Nitride) for ranges below 100bar-1500psi• Other diaphragms available on request
The rigid stem configuration makes installation fast and easy
The flexible configuration is designed forapplications requiring further thermal isola-tion or where installation would be otherwi-se difficult or impractical
The pressure / temperature configurationrequires only one mounting hole for themeasurement of both process values
The exposed capillary configuration isideal to fit in space-restricted locations
M30M30
M31M31
M32M32
M33M33
MECHANICAL DIMENSIONS
766,
5 [3
0,18
"]
152,
4 [6
"]
266,
1 [ 1
0,48
"]
152,
4 [ 6
"]15
2,4
[6"]
787
[31"
]
38.1
[1.5
"]
1/2 - 20UNF
ø10 -0.05[ ø0.394” -0.002 ]
M18x1.5
D1
D2
D3
D4
D5
A
B
C
Ch[Hex]
M30M30 M31M31
M32M32 M33M33
D1
D2
D3
D4
D5
A
B
C
Ch[Hex]
ø16 -0.08[ ø0.63” -0.003 ]
ø18 [ ø0.71” ]
6 -0.26[ 0.24” -0.01 ]
14.8 -0.4[ 0.58” -0.016 ]
19 [ 0.75” ]
19[ 3/4” ]
ø7.8 -0.05[ ø0.31” -0.002 ]
ø10.5 -0.025[ ø0.41” -0.001 ]
ø10.67 [ ø0.42” ]
ø12.7 [ ø0.5” ]
5.56 -0.26[ 0.22” -0.01 ]
11.2 [ 0.44” ]
15.74 [ 0.62” ]
16[ 5/8” ]
ø16 -0.4[ ø0.63” -0.016 ]
NOTE :Dimensions refer to rigid
stem length option “4”(153mm - 6”)
WARNING :For installation use amaximum tightening
torque of 56 Nm (500 in-lb)
ACCESSORIES
Connectors6-pin mating connector (IP65 protection degree) CON3008-pin mating connector CON307
ELECTRICAL CONNECTIONS
AccessoriesMounting bracket SF18Dummy plug for 1/2-20UNF SC12Dummy plug for M18x1.5 SC18Drill kit for 1/2-20UNF KF12Drill kit for M18x1.5 KF18Cleaning kit for 1/2-20UNF CT12Cleaning kit for M18x1.5 CT18
Thermocouple for M32 modelType “J” (153mm - 6” stem) TTER 718
Extension cables6-pin connector with 8m (25ft) cable C08WLS6-pin connector with 15m (50ft) cable C15WLS6-pin connector with 25m (75ft) cable C25WLS6-pin connector with 30m (100ft) cable C30WLS8-pin connector with 8m (25ft) cable E08WLS8-pin connector with 15m (50ft) cable E15WLS8-pin connector with 25m (75ft) cable E25WLS8-pin connector with 30m (100ft) cable E30WLSOther lengths consult factory
6 pin connectorVPT07RA10-6PT2
(PT02A-10-6P)
8 pin connectorPC02E-12-8P Bendix
mV/V OUTPUT
6-pin 8-pin
C
D
B
A
E - F
A
C
B
D
E - F
G - Hn.c.
Supply Voltage +
+
Signal
Calibration shunt
Supply Voltage -
-
Signal
R-Cal
Shield drain wire is tied toconnector via cable clamp
Conn. WireA RedB BlackC WhiteD GreenE BlueF BrownG n.c.H n.c.
Cable color code
cod. 85701 - 10/01UNI EN 29001 - ISO 9001Certificato nr. 9115.GEF1
ORDER CODE
Examples
M32-6-M-B07C-1-4-D-000Melt pressure transducer with type “J” thermocouple, 3.33 mV/V output, 6-pin connector, 1/2-20UNF thread, 700bar full scale, 0.5 % accuracy class, 153 mm (6”) rigid stem, 457mm (18”) flexible capillary.
M20-8-M-P03M-1-4-0-000Melt pressure transducer, rigid stem, 2.5 mV/V output, 8-pin connector, 1/2-20UNF thread, 3000psi full scale, 0.5 % accuracyclass, 153 mm (6”) rigid stem
THREAD
100 B01C70 B07D
RANGE
3550
B35UB05D
200
bar psi
B02C
500 B05C350 B35D
700 B07C
1500 P15C1000 P01M
500750
P05CP75D
3000 P03M
7500 P75C5000 P05M
10000 P10M
000 = Standard version Special or customized ver-sions available on request
1000 B01M 15000 P15M
CONNECTOR
6 pin 68 pin 8
ACCURACY CLASS
0.5% FSO M
0.25% FSO (ranges ≥ 100 bar/1500 psi)
H
OUTPUT SIGNAL2.5 mV/V 2
VERSIONRigid stem 0
Rigid stem + flexible 1
3With thermocouple 2
Exposed capillary
M
Standard
1/2 - 20 UNF1M18 x 1.54
Standard
Available on request2 M10 x 1
(ranges ≥ 200 bar/3000 psi)
3 M14 x 1.5
RIGID STEM LENGTH (mm / inches)
153mm4318mm5
Standard (M30, M31, M32)
Available on request1 38mm2 50mm3 76mm6 350mm7 400mm8 456mm
6”12.5”
1.5”2”3”14”16”18”
000
1400 B14C 20000 P20M
2000 B02M 30000 P30M
GEFRAN reserves the right to make any kind of design or functional modification at any moment without prior notice.
3.33 mV/V 3
Cannon WK 6-32S/1 GCannon WK 6-32S/2 B
Available on request
FLEXIBLE LENGTH (mm / inches)
457mmD610mmE
Standard (M30)
Available on requestA 76mmB 152mmC 300mmG 914mmH 1067mmI 1220mm
18”24”
3”6”12”36”42”48”
760mmF 30”
J 1372mmK 1520mm
54”60”
none0
Standard (M33)711mmL 28”
Standard (M31, M32)
none0Standard (M33)
GEFRAN spavia Sebina, 7425050 PROVAGLIO D’ISEO (BS) - ITALIAtel. 0309888.1 - fax. 0309839063Internet: http://www.gefran.comwww.gefranonline.com
MELT PRESSURE TRANSMITTERS
4-20 mA output
The rigid stem configuration makes installation fast and easy
The flexible configuration is designed forapplications requiring further thermal isola-tion or where installation would be otherwi-se difficult or impractical
The pressure / temperature configurationrequires only one mounting hole for themeasurement of both process values
The exposed capillary configuration isideal to fit in space-restricted locations
TECHNICAL SPECIFICATIONS
Nominal accuracy includingLinearity, Repeatibility, Hysteresis
Resolution
Measurement range
Maximum overpressure
Measurement principle
Supply voltage
Maximum current consumption
Isolation resistance (at 50Vdc)
Full Scale Output (FSO)
Zero balance
Signals adjustment : Nominal pressureAmbient pressure
Maximum load
Response time (10 to 90% FSO)
Output noise (RMS 10-400Hz)
Calibration signal
Protection against output shortcircuitand supply voltage inverted polarity
Protection against output voltagespikes
Strain gauge housing compensated tem-perature range
Maximum housing temperature range
Thermal drift in compensated rangeZero/Calibr./Sens.
Diaphragm maximum temperature
Zero drift due to change in processtemperature
Material in contact - Standardwith process medium
Thermocouple (model ME2)
Protection degree (with 6-pin matingconnector)
Electrical connections
H <±0.25%FSO (100...2000 bar)M <±0.5%FSO (35...2000 bar)
Infinite
0..35 to 0..2000bar0..500 to 0..30000psi
2 x FS 1.5 x FS above1000bar/15000psi
Strain gage Wheatstone bridge
12-30Vdc
20mA
>1000 MOhm
20mA
4mA
5% FSOmin. 10 bar (150psi)
see diagram (page 3)
~ 8ms
< 0.05% FSO
80% FSO
YES
YESaccording to 89/336/EEC
0...+76°C32...170°F
-30...+85°C -22...185°F
< 0.02%FSO/°C< 0.01%FSO/°F
400°C 750°F
0.02 bar/°C15 psi/100°F
15-5 PH with Armoloy coating 17-7 PH corrugated diaphragm withTitanium Nitride coating for ranges
<100 bar (1500psi)
STD : type “J” (isolated junction)
IP65
6-pin Conn. VPT07RA10-6PT(PT02A-10-6P)
8-pin Conn. PC02E-12-8P
FSO = Full Scale Output (output signal at nominal pressure)
ME0ME0
ME1ME1
ME2ME2
ME3ME3
Main features
• Pressure ranges from:0-35 to 0-2000 bar / 0-500 to 0-30000 psi
• Strain gage Wheatstone bridge• Accuracy :
<±0.25% FSO (H); <±0.5% FSO (M)• Internally generated 80% calibration signal (R-Cal)• Fluid-filled system for temperature stability • Fully interchangeable with all existing brands• Grade of protection: IP65 (6-pin connector version)• 1/2-20UNF , M18x1.5 standard threads ; other types
available on request• Standard diaphragm is 15-5 PH stainless steel with
Armoloy coating • 17-7 PH corrugated diaphragm with TiN coating
(Titanium Nitride) for ranges below 100bar-1500psi• Other diaphragms available on request
MECHANICAL DIMENSIONS
152,
4 [6
"]
766,
5 [3
0,18
"]
266,
1 [1
0,48
"]
152,
4 [6
"]15
2,4
[6"]
787
[31"
]
38,1
[1.5
"]
1/2 - 20UNF
ø10 -0.05[ ø0.394” -0.002 ]
M18x1,5
D1
D2
D3
D4
D5
A
B
C
Ch[Hex]
ME0ME0 ME1ME1
ME2ME2 ME3ME3
D1
D2
D3
D4
D5
A
B
C
Ch[Hex]
ø16 -0.08[ ø0.63” -0.003 ]
ø18 [ ø0.71” ]
6 -0.26[ 0.24” -0.01 ]
14.8 -0.4[ 0.58” -0.016 ]
19 [ 0.75” ]
19[ 3/4” ]
ø7.8 -0.05[ ø0.31” -0.002 ]
ø10.5 -0.025[ ø0.41” -0.001 ]
ø10.67 [ ø0.42” ]
ø12.7 [ ø0.5” ]
5.56 -0.26[ 0.22” -0.01 ]
11.2 [ 0.44” ]
15.74 [ 0.62” ]
16[ 5/8” ]
ø16 -0.4[ ø0.63” -0.016 ]
NOTE :Dimensions refer to rigid
stem length option “4”(153mm - 6”)
WARNING :For installation use amaximum tightening
torque of 56 Nm(500 in-lb)
ACCESSORIES
Connectors6-pin mating connector (IP65 protection degree) CON3008-pin mating connector CON307
ELECTRICAL CONNECTIONS
AccessoriesMounting bracket SF18Dummy plug for 1/2-20UNF SC12Dummy plug for M18x1.5 SC18Drill kit for 1/2-20UNF KF12Drill kit for M18x1.5 KF18Cleaning kit for 1/2-20UNF CT12Cleaning kit for M18x1.5 CT18
Thermocouple for ME2 modelType “J” (153mm - 6” stem) TTER 718
Extension cables6-pin connector with 8m (25ft) cable C08WLS6-pin connector with 15m (50ft) cable C15WLS6-pin connector with 25m (75ft) cable C25WLS6-pin connector with 30m (100ft) cable C30WLS8-pin connector with 8m (25ft) cable E08WLS8-pin connector with 15m (50ft) cable E15WLS8-pin connector with 25m (75ft) cable E25WLS8-pin connector with 30m (100ft) cable E30WLSOther lengths consult factory
CURRENT OUTPUT (4...20mA two wires)
LOAD DIAGRAM FOR CURRENT OUTPUT ADJUSTMENTS
ZERO and SPAN adjustmentcan be made by trimpots insi-de the transmitter body andaccessible after removing thetwo protection screws.
Span is factory set andshould not be adjusted.
The diagram shows the optimum ratio between the load andsupply voltage of the 4-20mA transmitter.For a correct use, choose any combination of load resistanceand supply voltage, in the shaded area.
6 pin connectorVPT07RA10-6PT2
(PT02A-10-6P)
LOA
D R
ES
ISTA
NC
E R
L
SUPPLY VOLTAGE
USEFULAREA
6-pin 8-pin
A
C
B
D
E - F
B
A
D
C
E - F
G - H
n.c.
8 pin connectorPC02E-12-8P Bendix
CONTROLLER
AMPL./CONV.
n.c.
n.c.
Supply Voltage(12..30 Vdc)
+
-Signal
(4..20 mA)
Calibration shunt
Shield drain wire is tied toconnector via cable clamp
Conn. WireA RedB BlackC WhiteD GreenE BlueF BrownG n.c.H n.c.
Cable color code
cod. 85707 - 10/01UNI EN 29001 - ISO 9001Certificato nr. 9115.GEF1
ORDER CODE
Examples
ME2-6-M-B07C-1-4-D-000Melt pressure transmitter with type “J” thermocouple, 4..20 mA output, 6-pin connector, 1/2-20UNF thread, 700bar full scale,0.5 % accuracy class, 153 mm (6”) rigid stem, 457mm (18”) flexible capillary.
ME0-8-M-P03M-1-4-0-000Melt pressure transmitter, rigid stem, 4..20 mA output, 8-pin connector, 1/2-20UNF thread, 3000psi full scale, 0.5 % accuracyclass, 153 mm (6”) rigid stem
100 B01C70 B07D
RANGE
3550
B35UB05D
200
bar psi
B02C
500 B05C350 B35D
700 B07C
1500 P15C1000 P01M
500750
P05CP75D
3000 P03M
7500 P75C5000 P05M
10000 P10M
000 = Standard version Special or customized versionsavailable on request
1000 B01M 15000 P15M
CONNECTOR
6 pin 68 pin 8
ACCURACY CLASS
0.5% FSO M
0.25% FSO (ranges ≥ 100 bar/1500 psi)
H
OUTPUT SIGNAL4...20mA E
VERSIONRigid stem 0
Rigid stem + flexible 1
3With thermocouple 2
Exposed capillary
Standard
Available on requestNNPT
1400 B14C 20000 P20M
2000 B02M 30000 P30M
GEFRAN reserves the right to make any kind of design or functional modification at any moment without prior notice.
M 000
THREAD
1/2 - 20 UNF1M18 x 1.54
Standard
Available on request2 M10 x 1
(ranges ≥ 200 bar/3000 psi)
3 M14 x 1.5
RIGID STEM LENGTH (mm / inches)
153mm4318mm5
Standard (ME0, ME1, ME2)
Available on request1 38mm2 50mm3 76mm6 350mm7 400mm8 456mm
6”12.5”
1.5”2”3”14”16”18”
FLEXIBLE LENGTH (mm / inches)
457mmD610mmE
Standard (ME0)
Available on requestA 76mmB 152mmC 300mmG 914mmH 1067mmI 1220mm
18”24”
3”6”12”36”42”48”
760mmF 30”
J 1372mmK 1520mm
54”60”
none0
Standard (ME3)711mmL 28”
Standard (ME1, ME2)
none0Standard (ME3)
GEFRAN spavia Sebina, 7425050 PROVAGLIO D’ISEO (BS) - ITALIAtel. 0309888.1 - fax. 0309839063Internet: http://www.gefran.comwww.gefranonline.com
MELT PRESSURE TRANSMITTERS
Voltage output
The rigid stem configuration makes installation fast and easy
The flexible configuration is designed forapplications requiring further thermal isola-tion or where installation would be otherwi-se difficult or impractical
The pressure / temperature configurationrequires only one mounting hole for themeasurement of both process values
The exposed capillary configuration isideal to fit in space-restricted locations
TECHNICAL SPECIFICATIONS
Nominal accuracy includingLinearity, Repeatibility, Hysteresis
Resolution
Measurement range
Maximum overpressure
Measurement principle
Supply voltage
Maximum current consumption
Isolation resistance (at 50Vdc)
Full Scale Output (FSO)
Zero balance
Signals adjustment : Nominal pressureAmbient pressure
Maximum load
Response time (10 to 90% FSO)
Output noise (RMS 10-400Hz)
Calibration signal
Protection against output shortcircuitand supply voltage inverted polarity
Protection against output voltagespikes
Strain gauge housing compensated tem-perature range
Maximum housing temperature range
Thermal drift in compensated rangeZero/Calibr./Sens.
Diaphragm maximum temperature
Zero drift due to change in processtemperature
Material in contact - Standardwith process medium
Thermocouple (model MN2)
Protection degree
Electrical connections
H <±0.25%FSO (100...2000 bar)M <±0.5%FSO (35...2000 bar)
Infinite
0..35 to 0..2000bar0..500 to 0..30000psi
2 x FS 1.5 x FS above1000bar/15000psi
Strain gage Wheatstone bridge
15-30Vdc
40mA (1)
>1000 MOhm
5Vdc (M, H) 5.1Vdc (B)10Vdc (N, L) 10.1Vdc (C)
0Vdc (M, N, H, L)0.1Vdc (B, C)
5% FSOmin. 10 bar (150psi)
1mA
~ 4ms
< 0.05% FSO
80% FSO
YES
YESAccording to 89/336/EEC
0...+76°C32...170°F
-30...+85°C -22...185°F
< 0.02 %FSO/°C< 0.01 %FSO/°F
400°C 750°F
0.02 bar/°C 15 psi/100°F
15-5 PH with Armoloy coating 17-7 PH corrugated diaphragm withTitanium Nitride coating for ranges
<100 bar (1500psi)
STD : type “J” (isolated junction)
IP65
6-pin Conn. VPT07RA10-6PT(PT02A-10-6P)
FSO = Full Scale Output (output signal at nominal pressure)
MN0MN0
MN1MN1
MN2MN2
MN3MN3
Main features
• Pressure ranges from:0-35 to 0-2000 bar / 0-500 to 0-30000 psi
• Strain gage Wheatstone bridge• Accuracy :
<±0.25% FSO (H); <±0.5% FSO (M)• Internally generated 80% calibration signal (R-Cal)• Fluid-filled system for temperature stability • Fully interchangeable with all existing brands• Grade of protection: IP65• 1/2-20UNF , M18x1.5 standard threads ; other types
available on request• Standard diaphragm is 15-5 PH stainless steel with
Armoloy coating • 17-7 PH corrugated diaphragm with TiN coating
(Titanium Nitride) for ranges below 100bar-1500psi• Other diaphragms available on request
(1) Conditions : 30Vdc supply, maximum allowed load, calibration shuntinserted
MECHANICAL DIMENSIONS
152,
4 [6
"]
766,
5 [3
0,18
"]
266,
1 [1
0,48
"]
152,
4 [6
"]15
2,4
[6"]
787
[31"
]
38,1
[1.5
"]
1/2 - 20UNF
ø10 -0.05[ ø0.394” -0.002 ]
M18x1,5
D1
D2
D3
D4
D5
A
B
C
Ch[Hex]
MN0MN0 MN1MN1
MN2MN2 MN3MN3
D1
D2
D3
D4
D5
A
B
C
Ch[Hex]
ø16 -0.08[ ø0.63” -0.003 ]
ø18 [ ø0.71” ]
6 -0.26[ 0.24” -0.01 ]
14.8 -0.4[ 0.58” -0.016 ]
19 [ 0.75” ]
19[ 3/4” ]
ø7.8 -0.05[ ø0.31” -0.002 ]
ø10.5 -0.025[ ø0.41” -0.001 ]
ø10.67 [ ø0.42” ]
ø12.7 [ ø0.5” ]
5.56 -0.26[ 0.22” -0.01 ]
11.2 [ 0.44” ]
15.74 [ 0.62” ]
16[ 5/8” ]
ø16 -0.4[ ø0.63” -0.016 ]
NOTE :Dimensions refer to rigid
stem length option “4”(153mm - 6”)
WARNING :For installation use amaximum tightening
torque of 56 Nm500 in-lb
ACCESSORIES
Connectors6-pin mating connector (IP65 protection degree) CON300
ELECTRICAL CONNECTIONS
AccessoriesMounting bracket SF18Dummy plug for 1/2-20UNF SC12Dummy plug for M18x1.5 SC18Drill kit for 1/2-20UNF KF12Drill kit for M18x1.5 KF18Cleaning kit for 1/2-20UNF CT12Cleaning kit for M18x1.5 CT18
Thermocouple for MN2 modelType “J” (153mm - 6” stem) TTER 718
Extension cables6-pin connector with 8m (25ft) cable C08WLS6-pin connector with 15m (50ft) cable C15WLS6-pin connector with 25m (75ft) cable C25WLS6-pin connector with 30m (100ft) cable C30WLS
Other lengths consult factory
VOLTAGE OUTPUT (M, N, B, C)Power supply 15..30Vdc
ADJUSTMENTS
ZERO and SPAN adjustmentcan be made by trimpots insidethe transmitter body and acces-sible after removing the two pro-tection screws.
SPAN is factory set andshould not be adjusted.
6 pin connectorVPT07RA10-6PT2
(PT02A-10-6P)6-pin
C
D
A
B
E - F
CONTROLLER
AMPLIFIER
Supply Voltage +
+Signal
Calibration shunt
Supply Voltage -
-Signal
VOLTAGE OUTPUT (H, L)Power supply -15..+15Vdc
6-pin
C
D
A
B
E - F
CONTROLLER
AMPLIFIER
Supply Voltage (+15Vdc)
+Signal
Calibration shunt
Supply Voltage (-15Vdc)
-Signal
Shield drain wire is tied toconnector via cable clamp
Shield drain wire is tied toconnector via cable clamp
Conn. WireA RedB BlackC WhiteD GreenE BlueF Brown
Cable color code
cod. 85713 - 09/01UNI EN 29001 - ISO 9001Certificato nr. 9115.GEF1
ORDER CODE
Examples
MN2-6-M-B07C-1-4-D-000Melt pressure transmitter with type “J” thermocouple, 0..10Vdc output, 6-pin connector, 1/2-20UNF thread, 700bar full scale, 0.5 % accuracy class, 153 mm (6”) rigid stem, 457mm (18”) flexible capillary.
MM0-6-M-P03M-1-4-0-000Melt pressure transmitter, rigid stem, 0..5Vdc output, 6-pin connector, 1/2-20UNF thread, 3000psi full scale, 0.5 % accuracyclass, 153 mm (6”) rigid stem
100 B01C70 B07D
RANGE
3550
B35UB05D
200
bar psi
B02C
500 B05C350 B35D
700 B07C
1500 P15C1000 P01M
500750
P05CP75D
3000 P03M
7500 P75C5000 P05M
10000 P10M
000 = Standard version Special or customized versionsavailable on request
1000 B01M 15000 P15M
CONNECTOR
6 pin 6
ACCURACY CLASS
0.5% FSO M
0.25% FSO (ranges ≥ 100 bar/1500 psi)
H
OUTPUT SIGNAL0 .. 5Vdc M
VERSIONRigid stem 0
Rigid stem + flexible 1
3With thermocouple 2
Exposed capillary
Standard
1400 B14C 20000 P20M
2000 B02M 30000 P30M
GEFRAN reserves the right to make any kind of design or functional modification at any moment without prior notice.
0 .. 10Vdc N0.1 .. 5.1Vdc B
H0.1 .. 10.1Vdc C
0..5Vdc (-15/+15Vdc supply)
L0..10Vdc (-15/+15Vdc supply)
M 000
THREAD
1/2 - 20 UNF1M18 x 1.54
Standard
Available on request2 M10 x 1
(ranges ≥ 200 bar/3000 psi)
3 M14 x 1.5
RIGID STEM LENGTH (mm / inches)
153mm4318mm5
Standard (MN0, MN1, MN2)
Available on request1 38mm2 50mm3 76mm6 350mm7 400mm8 456mm
6”12.5”
1.5”2”3”14”16”18”
FLEXIBLE LENGTH (mm / inches)
457mmD610mmE
Standard (MN0)
Available on requestA 76mmB 152mmC 300mmG 914mmH 1067mmI 1220mm
18”24”
3”6”12”36”42”48”
760mmF 30”
J 1372mmK 1520mm
54”60”
none0
Standard (MN3)711mmL 28”
Standard (MN1, MN2)
none0Standard (MN3)
GEFRAN spavia Sebina, 7425050 PROVAGLIO D’ISEO (BS) - ITALIAtel. 0309888.1 - fax. 0309839063Internet: http://www.gefran.comwww.gefranonline.com
OIL-FILLEDMELT PRESSURE TRANSDUCERS
mV/V output
The rigid stem configuration makes installation fast and easy
The flexible configuration is designed forapplications requiring further thermal isola-tion or where installation would be otherwi-se difficult or impractical
The pressure / temperature configurationrequires only one mounting hole for themeasurement of both process values
The exposed capillary configuration isideal to fit in space restricted locations
TECHNICAL SPECIFICATIONS
Nominal accuracy includingLinearity, Repeatibility, Hysteresis
Resolution
Measurement range
Maximum overpressure
Measurement principle
Supply voltage
Strain gage bridge resistance
Isolation resistance (at 50Vdc)
Full Scale Output (FSO)
Zero balance
Calibration signal
Strain gauge housing compensated tem-perature range
Maximum housing temperature range
Thermal drift in compensated rangeZero/Calibr./Sens.
Diaphragm maximum temperature
Zero drift due to change in processtemperature
Material in contact - Standardwith process medium
- Optional
Thermocouple (model W32)
Protection degree (with 6-pin matingconnector)
Electrical connections
H <±0.25%FSO (350...1000 bar)M <±0.5%FSO (35...1000 bar)
Infinite
0..35 to 0..1000bar0..500 to 0..15000psi
2 x FS 1.5 x FS above 500bar/7500psi
Strain gage Wheatstone bridge
6..12Vdc (10Vdc typical)
350 Ohm(550 Ohm below 100bar - 1500psi)
>1000 MOhm
2.5 mV/V (option 2)3.33 mV/V (option 3)
±5%
80% FSO
0...+100°C32...212°F
-30...+120°C -22...250°F
< 0.02% FSO/°C< 0.01% FSO/°F
315°C 600°F
0.04 bar/°C30 psi/100°F
17-7PH corrugated diaphragm with Titanium Nitride coating
17-7PH corrugated diaphragm with Chromium Nitride coating
STD : type “J” (isolated junction)
IP65
6-pin Conn. VPT07RA10-6PT(PT02A-10-6P)
8-pin Conn. PC02E-12-8P
FSO = Full Scale Output (output signal at nominal pressure)
W30W30
W31W31
W32W32
W33W33
Main features
• Pressure ranges from:0-35 to 0-1000 bar / 0-500 to 0-15000 psi
• Strain gage Wheatstone bridge• Accuracy :
<±0.25% FSO (H); <±0.5% FSO (M)• Internally generated 80% calibration signal (R-Cal)• Fluid-filled system for temperature stability • Oil filling meets FDA requirements
CFR 178.3620 and CFR 172.878• Fully interchangeable with all existing brands• Grade of protection: IP65 (6-pin connector version)• 1/2-20UNF , M18x1.5 standard threads ; other types
available on request• Standard diaphragm is a 17-7 PH stainless steel
TiN (Titanium Nitride) coated corrugated diaphragm
MECHANICAL DIMENSIONS
766,
5 [3
0,18
"]
152,
4 [6
"]
266,
1 [ 1
0,48
"]
152,
4 [ 6
"]15
2,4
[6"]
787
[31"
]
38.1
[1.5
"]
1/2 - 20UNF
ø10 -0.05[ ø0.394” -0.002 ]
M18x1,5
D1
D2
D3
D4
D5
A
B
C
Ch[Hex]
W30W30 W31W31
W32W32 W33W33
D1
D2
D3
D4
D5
A
B
C
Ch[Hex]
ø16 -0.08[ ø0.63” -0.003 ]
ø18 [ ø0.71” ]
6 -0.26[ 0.24” -0.01 ]
14.8 -0.4[ 0.58” -0.016 ]
19 [ 0.75” ]
19[ 3/4” ]
ø7.8 -0.05[ ø0.31” -0.002 ]
ø10.5 -0.025[ ø0.41” -0.001 ]
ø10.67 [ ø0.42” ]
ø12.7 [ ø0.5” ]
5.56 -0.26[ 0.22” -0.01 ]
11.2 [ 0.44” ]
15.74 [ 0.62” ]
16[ 5/8” ]
ø16 -0.4[ ø0.63” -0.016 ]
NOTE :Dimensions refer to rigid
stem length option “4”(153mm - 6”)
WARNING :For installation use amaximum tightening
torque of 56 Nm(500 in-lb)
ACCESSORIES
Connectors6-pin mating connector (IP65 protection degree) CON3008-pin mating connector CON307
ELECTRICAL CONNECTIONS
AccessoriesMounting bracket SF18Dummy plug for 1/2-20UNF SC12Dummy plug for M18x1.5 SC18Drill kit for 1/2-20UNF KF12Drill kit for M18x1.5 KF18Cleaning kit for 1/2-20UNF CT12Cleaning kit for M18x1.5 CT18
Thermocouple for W32 modelType “J” (153mm - 6” stem) TTER 718
Extension cables6-pin connector with 8m (25ft) cable C08WLS6-pin connector with 15m (50ft) cable C15WLS6-pin connector with 25m (75ft) cable C25WLS6-pin connector with 30m (100ft) cable C30WLS8-pin connector with 8m (25ft) cable E08WLS8-pin connector with 15m (50ft) cable E15WLS8-pin connector with 25m (75ft) cable E25WLS8-pin connector with 30m (100ft) cable E30WLSOther lengths consult factory
6 pin connectorVPT07RA10-6PT2
(PT02A-10-6P)
8 pin connectorPC02E-12-8P Bendix
mV/V OUTPUT
6-pin 8-pin
C
D
B
A
E - F
A
C
B
D
E - F
G - Hn.c.
Supply Voltage +
+
Signal
Calibration shunt
Supply Voltage -
-
Signal
R-Cal
Shield drain wire is tied toconnector via cable clamp
Conn. WireA RedB BlackC WhiteD GreenE BlueF BrownG n.c.H n.c.
Cable color code
cod. 85719 - 09/01UNI EN 29001 - ISO 9001Certificato nr. 9115.GEF1
ORDER CODE
Examples
W32-6-M-B07C-1-4-D-000Melt pressure transducer with type “J” thermocouple, 3.33 mV/V output, 6-pin connector, 1/2-20UNF thread, 700bar full scale, 0.5 % accuracy class, 153 mm (6”) rigid stem, 457mm (18”) flexible capillary.
W20-8-M-P03M-1-4-0-000Melt pressure transducer, rigid stem, 2.5 mV/V output, 8-pin connector, 1/2-20UNF thread, 3000psi full scale, 0.5 % accuracyclass, 153 mm (6”) rigid stem
THREAD
100 B01C70 B07D
RANGE
3550
B35UB05D
200
bar psi
B02C
500 B05C350 B35D
700 B07C
1500 P15C1000 P01M
500750
P05CP75D
3000 P03M
7500 P75C5000 P05M
10000 P10M
000 = Standard version Special or customized versionsavailable on request
1000 B01M 15000 P15M
CONNECTOR
6 pin 68 pin 8
ACCURACY CLASS
0.5% FSO M
0.25% FSO (ranges ≥ 350 bar/5000 psi)
H
OUTPUT SIGNAL
VERSIONRigid stem 0
Rigid stem + flexible 1
3With thermocouple 2
Exposed capillary
Standard
1/2 - 20 UNF1M18 x 1.54
Standard
RIGID STEM LENGTH (*)(mm / inches)
153mm4318mm5
Standard (W30, W31, W32)
Available on request1 38mm2 50mm3 76mm6 350mm7 400mm8 456mm
6”12.5”
1.5”2”3”14”16”18”
GEFRAN reserves the right to make any kind of design or functional modification at any moment without prior notice.
Cannon WK 6-32S/1 GCannon WK 6-32S/2 B
Available on request
FLEXIBLE LENGTH (*)(mm / inches)
457mmD610mmE
Standard (W30)
Available on requestA 76mmB 152mmC 300mm
18”24”
3”6”12”
760mmF 30”
none0
Standard (W33)711mmL 28”
Standard (W31, W32)
2.5 mV/V 23.33 mV/V 3
(*) Note : maximum combined stem/flex length is914mm - 36”
W 000
none0Standard (W33)
GEFRAN spavia Sebina, 7425050 PROVAGLIO D’ISEO (BS) - ITALIAtel. 0309888.1 - fax. 0309839063Internet: http://www.gefran.comwww.gefranonline.com
OIL-FILLEDMELT PRESSURE TRANSMITTERS
4-20 mA output
The rigid stem configuration makes installation fast and easy
The flexible configuration is designed forapplications requiring further thermal isola-tion or where installation would be otherwi-se difficult or impractical
The pressure / temperature configurationrequires only one mounting hole for themeasurement of both process values
The exposed capillary configuration isideal to fit in space restricted locations
TECHNICAL SPECIFICATIONS
Nominal accuracy includingLinearity, Repeatibility, Hysteresis
Resolution
Measurement range
Maximum overpressure
Measurement principle
Supply voltage
Maximum current consumption
Isolation resistance (at 50Vdc)
Full Scale Output (FSO)
Zero balance
Signals adjustment : Nominal pressureAmbient pressure
Maximum load
Response time (10 to 90% FSO)
Output noise (RMS 10-400Hz)
Calibration signal
Protection against output shortcircuitand supply voltage inverted polarity
Protection against output voltagespikes
Strain gauge housing compensated tem-perature range
Maximum housing temperature range
Thermal drift in compensated rangeZero/Calibr./Sens.
Diaphragm maximum temperature
Zero drift due to change in processtemperature
Material in contact - Standardwith process medium
- Optional
Thermocouple (model WE2)
Protection degree (with 6-pin matingconnector)
Electrical connections
H <±0.25%FSO (350...1000 bar)M <±0.5%FSO (35...1000 bar)
Infinite
0..35 to 0..1000bar0..500 to 0..15000psi
2 x FS 1.5 x FS above 500bar/7500psi
Strain gage Wheatstone bridge
12-30Vdc
20mA
>1000 MOhm
20mA
4mA
5% FSOmin. 10 bar (150psi)
see diagram (page 3)
~ 8ms
< 0.05% FSO
80% FSO
YES
YESaccording to 89/336/EEC
0...+76°C32...170°F
-30...+85°C -22...185°F
< 0.02% FSO/°C< 0.01% FSO/°F
315°C 600°F
0.04 bar/°C 30 psi/100°F
17-7PH corrugated diaphragm with Titanium Nitride coating
17-7PH corrugated diaphragm with Chromium Nitride coating
STD : type “J” (isolated junction)
IP65
6-pin Conn. VPT07RA10-6PT(PT02A-10-6P)
8-pin Conn. PC02E-12-8P
FSO = Full Scale Output (output signal at nominal pressure)
WE0WE0
WE1WE1
WE2WE2
WE3WE3
Main features
• Pressure ranges from:0-35 to 0-1000 bar / 0-500 to 0-15000 psi
• Strain gage Wheatstone bridge• Accuracy :
<±0.25% FSO (H); <±0.5% FSO (M)• Internally generated 80% calibration signal (R-Cal)• Fluid-filled system for temperature stability • Oil filling meets FDA requirements
CFR 178.3620 and CFR 172.878• Fully interchangeable with all existing brands• Grade of protection: IP65 (6-pin connector version)• 1/2-20UNF , M18x1.5 standard threads ; other types
available on request• Standard diaphragm is a 17-7 PH stainless steel
TiN (Titanium Nitride) coated corrugated diaphragm
MECHANICAL DIMENSIONS
152,
4 [6
"]
766,
5 [3
0,18
"]
266,
1 [1
0,48
"]
152,
4 [6
"]15
2,4
[6"]
787
[31"
]
38,1
[1.5
"]
1/2 - 20UNF
ø10 -0.05[ ø0.394” -0.002 ]
M18x1,5
D1
D2
D3
D4
D5
A
B
C
Ch[Hex]
WE0WE0 WE1WE1
WE2WE2 WE3WE3
D1
D2
D3
D4
D5
A
B
C
Ch[Hex]
ø16 -0.08[ ø0.63” -0.003 ]
ø18 [ ø0.71” ]
6 -0.26[ 0.24” -0.01 ]
14.8 -0.4[ 0.58” -0.016 ]
19 [ 0.75” ]
19[ 3/4” ]
ø7.8 -0.05[ ø0.31” -0.002 ]
ø10.5 -0.025[ ø0.41” -0.001 ]
ø10.67 [ ø0.42” ]
ø12.7 [ ø0.5” ]
5.56 -0.26[ 0.22” -0.01 ]
11.2 [ 0.44” ]
15.74 [ 0.62” ]
16[ 5/8” ]
ø16 -0.4[ ø0.63” -0.016 ]
NOTE :Dimensions refer to rigid
stem length option “4”(153mm - 6”)
WARNING :For installation use amaximum tightening
torque of 56 Nm(500 in-lb)
ACCESSORIES
Connectors6-pin mating connector (IP65 protection degree) CON3008-pin mating connector CON307
ELECTRICAL CONNECTIONS
AccessoriesMounting bracket SF18Dummy plug for 1/2-20UNF SC12Dummy plug for M18x1.5 SC18Drill kit for 1/2-20UNF KF12Drill kit for M18x1.5 KF18Cleaning kit for 1/2-20UNF CT12Cleaning kit for M18x1.5 CT18
Thermocouple for WE2 modelType “J” (153mm - 6” stem) TTER 718
Extension cables6-pin connector with 8m (25ft) cable C08WLS6-pin connector with 15m (50ft) cable C15WLS6-pin connector with 25m (75ft) cable C25WLS6-pin connector with 30m (100ft) cable C30WLS8-pin connector with 8m (25ft) cable E08WLS8-pin connector with 15m (50ft) cable E15WLS8-pin connector with 25m (75ft) cable E25WLS8-pin connector with 30m (100ft) cable E30WLSOther lengths consult factory
CURRENT OUTPUT (4...20mA two wires)
LOAD DIAGRAM FOR CURRENT OUTPUT ADJUSTMENTS
ZERO and SPAN adjustmentcan be made by relative trim-pots inside the transmitterbody and accessible afterremoving the two protectionscrews.
Span is factory set andshould not be adjusted.
The diagram shows the optimum ratio between the load andsupply voltage of the 4-20mA transmitter.For a correct use, choose any combination of load resistanceand supply voltage, in the shaded area.
6 pin connectorVPT07RA10-6PT2
(PT02A-10-6P)
LOA
D R
ES
ISTA
NC
E R
L
SUPPLY VOLTAGE
USEFULAREA
6-pin 8-pin
A
C
B
D
E - F
B
A
D
C
E - F
G - H
n.c.
8 pin connectorPC02E-12-8P Bendix
CONTROLLER
AMPL./CONV.
n.c.
n.c.
Supply Voltage(12..30 Vdc)
+
-Signal
(4..20 mA)
Calibration shunt
Shield drain wire is tied toconnector via cable clamp
Conn. WireA RedB BlackC WhiteD GreenE BlueF BrownG n.c.H n.c.
Cable color code
cod. 85725 - 09/01UNI EN 29001 - ISO 9001Certificato nr. 9115.GEF1
ORDER CODE
Examples
WE2-6-M-B07C-1-4-D-000Melt pressure transmitter with type “J” thermocouple, 4..20 mA output, 6-pin connector, 1/2-20UNF thread, 700bar full scale,0.5 % accuracy class, 153 mm (6”) rigid stem, 457mm (18”) flexible capillary.
WE0-8-M-P03M-1-4-0-000Melt pressure transmitter, rigid stem, 4..20 mA output, 8-pin connector, 1/2-20UNF thread, 3000psi full scale, 0.5 % accuracyclass, 153 mm (6”) rigid stem
THREAD
100 B01C70 B07D
RANGE
3550
B35UB05D
200
bar psi
B02C
500 B05C350 B35D
700 B07C
1500 P15C1000 P01M
500750
P05CP75D
3000 P03M
7500 P75C5000 P05M
10000 P10M
000 = Standard version Special or customized versionsavailable on request
1000 B01M 15000 P15M
CONNECTOR
6 pin 68 pin 8
ACCURACY CLASS
0.5% FSO M
0.25% FSO (ranges ≥ 350 bar/5000 psi)
H
OUTPUT SIGNAL4...20mA E
VERSIONRigid stem 0
Rigid stem + flexible 1
3With thermocouple 2
Exposed capillary
Standard
Available on requestNNPT
1/2 - 20 UNF1M18 x 1.54
Standard
GEFRAN reserves the right to make any kind of design or functional modification at any moment without prior notice.
W 000
RIGID STEM LENGTH (*)(mm / inches)
153mm4318mm5
Standard (WE0, WE1, WE2)
Available on request1 38mm2 50mm3 76mm6 350mm7 400mm8 456mm
6”12.5”
1.5”2”3”14”16”18”
FLEXIBLE LENGTH (*)(mm / inches)
457mmD610mmE
Standard (WE0)
Available on requestA 76mmB 152mmC 300mm
18”24”
3”6”12”
760mmF 30”
none0
Standard (WE3)711mmL 28”
Standard (WE1, WE2)
(*) Note : maximum combined stem/flex length is914mm - 36”
none0Standard (WE3)
GEFRAN spavia Sebina, 7425050 PROVAGLIO D’ISEO (BS) - ITALIAtel. 0309888.1 - fax. 0309839063Internet: http://www.gefran.comwww.gefranonline.com
OIL-FILLEDMELT PRESSURE TRANSMITTERS
Voltage output
The rigid stem configuration makes installation fast and easy
The flexible configuration is designed forapplications requiring further thermal isola-tion or where installation would be otherwi-se difficult or impractical
The pressure / temperature configurationrequires only one mounting hole for themeasurement of both process values
The exposed capillary configuration isideal to fit in space restricted locations
TECHNICAL SPECIFICATIONS
Nominal accuracy includingLinearity, Repeatibility, Hysteresis
Resolution
Measurement range
Maximum overpressure
Measurement principle
Supply voltage
Maximum current consumption
Isolation resistance (at 50Vdc)
Full Scale Output (FSO)
Zero balance
Signals adjustment : Nominal pressureAmbient pressure
Maximum load
Response time (10 to 90% FSO)
Output noise (RMS 10-400Hz)
Calibration signal
Protection against output shortcircuitand supply voltage inverted polarity
Protection against output voltagespikes
Strain gauge housing compensated tem-perature range
Maximum housing temperature range
Thermal drift in compensated rangeZero/Calibr./Sens.
Diaphragm maximum temperature
Zero drift due to change in processtemperature
Material in contact - Standardwith process medium
- Optional
Thermocouple (model WN2)
Protection degree
Electrical connections
H <±0.25%FSO (350...1000 bar)M <±0.5%FSO (35...1000 bar)
Infinite
0..35 to 0..1000bar0..500 to 0..15000psi
2 x FS 1.5 x FS above 500bar/7500psi
Strain gage Wheatstone bridge
15-30Vdc
40mA (1)
>1000 MOhm
5Vdc (M)10Vdc (N)
0Vdc
5% FSOmin. 10 bar (150psi)
1mA
~ 4ms
< 0.05% FSO
80% FSO
YES
YESaccording to 89/336/EEC
0...+76°C32...170°F
-30...+85°C -22...185°F
< 0.02% FSO/°C< 0.01% FSO/°F
315°C 600°F
0.04 bar/°C30 psi/100°F
17-7PH corrugated diaphragm with Titanium Nitride coating
17-7PH corrugated diaphragm with Chromium Nitride coating
STD : type “J” (isolated junction)
IP65
6-pin Conn. VPT07RA10-6PT(PT02A-10-6P)
8-pin Conn. PC02E-12-8P
FSO = Full Scale Output (output signal at nominal pressure)
WN0WN0
WN1WN1
WN2WN2
WN3WN3
Main features
• Pressure ranges from:0-35 to 0-1000 bar / 0-500 to 0-15000 psi
• Strain gage Wheatstone bridge• Accuracy :
<±0.25% FSO (H); <±0.5% FSO (M)• Internally generated 80% calibration signal (R-Cal)• Fluid-filled system for temperature stability • Oil filling meets FDA requirements
CFR 178.3620 and CFR 172.878• Fully interchangeable with all existing brands• Grade of protection: IP65 (6-pin connector version)• 1/2-20UNF , M18x1.5 standard threads ; other types
available on request• Standard diaphragm is a 17-7 PH stainless steel
TiN (Titanium Nitride) coated corrugated diaphragm
(1) Conditions : 30Vdc supply, maximum allowed load, calibration shunt inserted
MECHANICAL DIMENSIONS
152,
4 [6
"]
766,
5 [3
0,18
"]
266,
1 [1
0,48
"]
152,
4 [6
"]15
2,4
[6"]
787
[31"
]
38,1
[1.5
"]
1/2 - 20UNF
ø10 -0.05[ ø0.394” -0.002 ]
M18x1,5
D1
D2
D3
D4
D5
A
B
C
Ch[Hex]
WN0WN0 WN1WN1
WN2WN2 WN3WN3
D1
D2
D3
D4
D5
A
B
C
Ch[Hex]
ø16 -0.08[ ø0.63” -0.003 ]
ø18 [ ø0.71” ]
6 -0.26[ 0.24” -0.01 ]
14.8 -0.4[ 0.58” -0.016 ]
19 [ 0.75” ]
19[ 3/4” ]
ø7.8 -0.05[ ø0.31” -0.002 ]
ø10.5 -0.025[ ø0.41” -0.001 ]
ø10.67 [ ø0.42” ]
ø12.7 [ ø0.5” ]
5.56 -0.26[ 0.22” -0.01 ]
11.2 [ 0.44” ]
15.74 [ 0.62” ]
16[ 5/8” ]
ø16 -0.4[ ø0.63” -0.016 ]
NOTE :Dimensions refer to rigid
stem length option “4”(153mm - 6”)
WARNING :For installation use amaximum tightening
torque of 56 Nm(500 in-lb)
ACCESSORIES
Connectors6-pin mating connector (IP65 protection degree) CON300
ELECTRICAL CONNECTIONS
AccessoriesMounting bracket SF18Dummy plug for 1/2-20UNF SC12Dummy plug for M18x1.5 SC18Drill kit for 1/2-20UNF KF12Drill kit for M18x1.5 KF18Cleaning kit for 1/2-20UNF CT12Cleaning kit for M18x1.5 CT18
Thermocouple for WN2 modelType “J” (153mm - 6” stem) TTER 718
Extension cables6-pin connector with 8m (25ft) cable C08WLS6-pin connector with 15m (50ft) cable C15WLS6-pin connector with 25m (75ft) cable C25WLS6-pin connector with 30m (100ft) cable C30WLSOther lengths consult factory
VOLTAGE OUTPUT (M, N)Power supply 15..30Vdc
ADJUSTMENTS
ZERO and SPAN adjust-ment can be made by rela-tive trimpots inside thetransmitter body andaccessible after removingthe two protection screws.
SPAN is factory set andshould not be adjusted.
6 pin connectorVPT07RA10-6PT2
(PT02A-10-6P)
6-pin
C
D
A
B
E - F
CONTROLLER
AMPLIFIER
Supply Voltage +
+Signal
Calibration shunt
Supply Voltage -
-Signal
Shield drain wire is tied toconnector via cable clamp
Conn. WireA RedB BlackC WhiteD GreenE BlueF Brown
Cable color code
cod. 85731 - 09/01UNI EN 29001 - ISO 9001Certificato nr. 9115.GEF1
ORDER CODE
Examples
WN2-6-M-B07C-1-4-D-000Melt pressure transmitter with type “J” thermocouple, 0..10Vdc output, 6-pin connector, 1/2-20UNF thread, 700bar full scale, 0.5 % accuracy class, 153 mm (6”) rigid stem, 457mm (18”) flexible capillary.
WM0-6-M-P03M-1-4-0Melt pressure transmitter, rigid stem, 0..5Vdc output, 6-pin connector, 1/2-20UNF thread, 3000psi full scale, 0.5 % accuracyclass, 153 mm (6”) rigid stem
THREAD
100 B01C70 B07D
RANGE
3550
B35UB05D
200
bar psi
B02C
500 B05C350 B35D
700 B07C
1500 P15C1000 P01M
500750
P05CP75D
3000 P03M
7500 P75C5000 P05M
10000 P10M
000 = Standard version Special or customized versionsavailable on request
1000 B01M 15000 P15M
CONNECTOR
6 pin 6
ACCURACY CLASS
0.5% FSO M
0.25% FSO (ranges ≥ 350 bar/5000 psi)
H
OUTPUT SIGNAL0 .. 5Vdc M
VERSIONRigid stem 0
Rigid stem + flexible 1
3With thermocouple 2
Exposed capillary
Standard
1/2 - 20 UNF1M18 x 1.54
Standard
GEFRAN reserves the right to make any kind of design or functional modification at any moment without prior notice.
0 .. 10Vdc N
W 000
RIGID STEM LENGTH (*)(mm / inches)
153mm4318mm5
Standard (WN0, WN1, WN2)
Available on request1 38mm2 50mm3 76mm6 350mm7 400mm8 456mm
6”12.5”
1.5”2”3”14”16”18”
FLEXIBLE LENGTH (*)(mm / inches)
457mmD610mmE
Standard (WN0)
Available on requestA 76mmB 152mmC 300mm
18”24”
3”6”12”
760mmF 30”
none0
Standard (WN3)711mmL 28”
Standard (WN1, WN2)
(*) Note : maximum combined stem/flex length is914mm - 36”
none0Standard (WN3)
GEFRAN spavia Sebina, 7425050 PROVAGLIO D’ISEO (BS) - ITALIAtel. 0309888.1 - fax. 0309839063Internet: http://www.gefran.comwww.gefranonline.com