pos530s user manual-v1.1
TRANSCRIPT
-
8/13/2019 POS530S User Manual-V1.1
1/35
Wirless POS530S Users Manual
Ve r s ion 1 .1
H a n g z h o u S u n y a r d Te c h n o l o g y C o . , L t d
A u g , 2 0 0 9
-
8/13/2019 POS530S User Manual-V1.1
2/35
Content
1. Introduction ............................................................................................................................................ 1
2. Operation Enviroment ........................... ............................... ............................... ................................ ... 1
2.1 Hardware Platform ............................................................................................................................ 1
2.2 Hardware Interface ........................................................................................................................... 1
2.3 Software Platform.............................................................................................................................. 1
3. The Profile of the POS...................................................... ............................... ............................... ......... 2
4. Operating Procedure .............................. ............................... ............................... ................................ ... 2
4.1 System Mode ...................................................................................................................................... 3
4.2 System Function ................................................................................................................................ 3
4.2.1 System Information...................................................................................................................... 3
4.2.2 Password Modification................................................................................................................. 3
4.2.3 System Setup ................................................................................................................................ 4
4.2.4 System Application....................................................................................................................... 5
4.3 API Test ............................................................................................................................................. 6
4.3.1 Beeper ........................................................................................................................................ 6
4.3.2 Printer ........................................................................................................................................ 6
4.3.3 Keyboard.................................................................................................................................... 7
4.3.4 LED .............................................................................................................................................. 8
4.3.5 LCD.............................................................................................................................................. 8
4.3.6 MGCard....................................................................................................................................... 8
4.3.7 ICCard ....................................................................................................................................... 9
4.3.8 SAMCard................................................................................................................................... 9
4.3.9 Battery....................................................................................................................................... 10
4.3.10 GPRS Module........................................................................................................................... 10
4.3.11 PINPAD............................... ................................ ............................... ............................... ........ 11
4.3.12 Security..................................................................................................................................... 11
4.3.13 MifareCard Reader............................. ............................... ................................ ....................... 12
4.3.14 RTC........................... ............................... ................................ ............................... .................. 15
4.3.15 USB interface...................................................... ............................... ............................... ........ 16
4.3.16 Logo.......................................................................................................................................... 18
4.3.17 Sleep............................... ............................... ................................ ............................... ............. 21
4.4 User ser ial port test..................................................... ............................... ............................... ........ 22
4.5 Phone Test........................................................................................................................................ 23
5. Program Update .................................................... ................................ ............................... .................. 24
5.1 Kernel Update............................. ................................ ............................... ............................... ........ 24
5.2 Download the key............................................................................................................................. 27
5.3 Download the Font li b................................................ ............................... ............................... ........ 30
5.4 Download the configurati on fi les of the wireless module................................................. .................. 32
-
8/13/2019 POS530S User Manual-V1.1
3/35
1
1. Introduction
This manual specifically explains the basic operation and cautionary items for
wireless POS-530S under the system mode.
This manual is particularly designed for the staff in charge of second-development
and relative users of wireless POS-530S.
2. Operation Enviroment
2.1 Hardware Platform CPU ATMEL AT91SAM9260 SDRAM SUMSUNG K4S561632E 32M Flash SUMSUNG K9F5608U0C 32M Network Card DAVCOM DM9161 Coulometer DS2780 Printer ELM208HS Pinpad STM32F101 V8 GPRS SIMCOM 340D
IC Card Reader AT83C26
Magnetic Card Reader ST43 SAM Card Reader AT83C26 LCD 12864pixel
2.2 Hardware Interface 1 Ethernet Interface !100M" 1 USB2.0 Interface 1 Serial Port !with 5V DC" 1 Debug Port
2.3 Software Platform LINUX Operation System (kernel 2.6.19)
-
8/13/2019 POS530S User Manual-V1.1
4/35
2
3. The Profile of the POS
4. Operating Procedure
-
8/13/2019 POS530S User Manual-V1.1
5/35
3
4.1 System Mode
Press Power Key to turn on the POS, press Fn and 2 (as a combination key) simultaneously,
hold on until the screen displays!System Password", then input corresponding password
(the default password of the system shall be !111111111111", sixteen !1"s in total). Next,
enter the following System Mode by pressing the key !ENTER"
4.2 System FunctionSelect 1. System Func into the system function you will see the following menu
4.2.1 System Information
System Info mainly displays relative configuration information of the POS
4.2.2Password Modification
The item Password is mainly used for password modification while entering
System Func.
Shift the cursor to the item Password through the Down Arrow key or press the NumberKey 2, next, press !ENTER", then enter the interface for selectingtochange the password or
not:
:
System Func
1. System Info2. Password3. Setup
System Mode1. System Func2. API Test3. Serial Test
Change Password
1#Yes
2#No
-
8/13/2019 POS530S User Manual-V1.1
6/35
4
Select Yes, and enter the interface for changing password. Then the user can input relative
password as you wish via the keypad (The new password should be input twice. The
modification becomes effective only if the 2nd
input is exactly in correspondence with the
1st input; otherwise, error will occur. );
Select No, and the password would remain unchanged. The system would
return to the interface of System Func.
4.2.3 System Setup
The item Setup is mainly used to set the IP address, time and LCD backlight of the Pos.
Shift the cursor to the Item Setup through the Down Arrow key or press the Number Key 3
directly in System Fucn mode. Press !Enter", and enter the interface System Setup as
follows:
Select Network, then press !Enter", you can enter the interface Network Setup asfollows
Item LocalIP is mainly used for the setup of IP address of the POS (to be in accord with the
setup of IP address), such as 9.100.2.147.
Item Netmask is mainly used for the setup of mask code, such as 255.255.255.0.
Item Gateway is mainly used for the setup of gateway address, such as 9.100.2.254.
Select RTC in System Setup mode, then press !Enter", the user can enter the interfacefor time setup.
Pressing the key !BACK"can delete the time paramenters set currently; Pressing
the Arrow up Key (which is equivalent to shifting to the left) can change the time.
System Setup
1#Network2#RTC3#Backligt
Network Setup
1#LocalIP2#Netmask3#Gateway
-
8/13/2019 POS530S User Manual-V1.1
7/35
5
Note: the allowed range of the time setup should be between 2000-00-00
00:00:00 to 2099-12-31 23:59:59.
Select Backlight in System Setup mode,, then press !Enter", the user will enter theinterface !Turn on Backlight"as follows:
Select Yes, and return to System Setup. LCD backlight would be turned on
(system$s default state);
Select No, and return to System Setup. LCD backlight would be turned off.
4.2.4 System Application
Item Application is used for the download and the deletion of application
programs, as well as the setup of server addresses and ports etc.
Shift the cursor to the Item Application or press Number Key 3 directly in the System Setup
mode, then press !Enter", to Select the Application download mode as follows:
Select Download, then press !Enter", you will see the Download Menu as follows:
Note: Before selecting Download, the IP address and port of the server for downl oading
application program shal l be set, and the net shal l be li nked, thus the POS can have
normal communi cation with the server; as for the detail setup, you can refer to the I tem
Config.
Turn On Backlight
1#Yes2#No
Download Menu
1#Download2#Config
Application
1#Download2#Delete
-
8/13/2019 POS530S User Manual-V1.1
8/35
6
Select Config in the Download Menu to enter the interface of setting the Server IP andports. After corresponding setup, press !Enter". Please conduct the setup as follows:
Server IP Address9.100.2.145
Server Port8163
Connect the POS with LAN (Local Area Network) via a LNA switching line,make sure that the pos can communicate with the server normally, and then select
Download, if the screen displays !Update App%Finished", it means that the download
is successful; if the screen displays !Connect Server Fail", it means that the download is
failed, and the network connection shall be checked.
Note: I f the download fai ls when the server runs normal ly, please check whether the
f ir ewall is turned off by the server side.
For detail you can reference with Application& Development Manual 2.3.2
4.3 API TestSelect API Test in the System mode Menu to enter the API test mode
4.3.1 BeeperCheck whether the beeper can work normally.
Choose !Beeper" in API TEST mode and press !ENTER", the screen shows !Press Any
Key", then the user can operate any key except the power key and cancel key to check the
beeper.
Press cancel to exit
4.3.2 PrinterCheck whether the printer can work normally.
Beeper Test
Press Any Key
-
8/13/2019 POS530S User Manual-V1.1
9/35
7
The printer inspection includes picture printing, English character printing, Chinese character
printing, print speed and the Black print
Select corresponding item to print the sepecified content. Select 7, and press ENTER key can
check the feeding function, andpress any two keys can stop feeding. In addition, press the
combination key !Fn+1"can also control the feeding function, stop feeding by releasing the
keys.
Note: Keep pri nting for too long can cause typing head hot, the info. Print Fail!will
display. It can work normaly after a time.and if the battery i s too low the print can"tBe
process normaly please char ge it
4.3.3 KeyboardCheck whether the key value can be read.
Choose !Keyboard"in API TEST mode and press !ENTER", the screen displays
corresponding key values when pressing relative number keys, while corresponding first
letters would be displayed when pressing other function keys, two key value at the most can
be displayed simultaneously, as follows:
Note: pressing the combination key cancel + 1!to exi t the key test pr ocess
Printer Test7. Feed Test
Printer Test
4. Speed Test5. Black Test6. Black Test(Gray)
Printer Test1. Bitmap2. English Text3. Chinese Text
Keyboard Test
Key Value:[ 1 ][ 2 ]
-
8/13/2019 POS530S User Manual-V1.1
10/35
8
4.3.4 LED
Check whether LED can display normally
Choose !LED in API TEST mode !and press !ENTER" to the !Led Test" interface, as
follows:
Select LED_ALL_ONBoth key LED of screen backlight and key are turned on
Select LED_ALL_OFFBoth key LED of screen backlight and key are turned off
Select LED_LCD_ONScreen backlight is turned on while key LED is off
Select LED_KEY_ONScreen backlight is turned off while key LED is on
4.3.5 LCD
Check whether LCD can display normally.
Choose !LCD"in API TEST mode and press !ENTER", you can press any key (except the
power key and cancel key) to check the font display,Press cancel to exit
4.3.6 MGCard
Check whether it can read the MG Carder normally
Choose !MGCard"in API TEST mode and press !ENTER", the screen displays !Please
Swipe Card%", put the magnetic side downward the LCD, and swipe it with a certain speed.
It supports bidirectional swipe, as follows:
Led Test
4. LED_KEY_ON
Led Test
1. LED_ALL_ON2. LED_ALL_OFF3. LED_LCD_ON
-
8/13/2019 POS530S User Manual-V1.1
11/35
9
After correct card-swiping, the track information of the magnetic card will be displayed, you
can press !ENTER",!UP"or !DOWN"key to turn page for viewing,and Press cancel to exit
4.3.7 ICCardCheck whether it can read the IC Carder normally.
Choose !ICCard"in API TEST mode and press !ENTER", the screen displays !Card Not
Present"if no IC Card inserted;
The screen shows corresponding return data when an IC Card is inserted.
Press !ENTER", the IC card information will be displayed, keep pressing !ENTER",!UP"or
!DOWN"key to turn page for viewing the info. Exit with the !Cancel"key.
Note: The interface of IC Card should be upturned and inserted along the IC Card slot.
4.3.8 SAMCardCheck whether it can read the SAM Card successfully.
Choose" SAMCard" in API TEST mode and press !ENTER" to the !SAM Card Test"
interface, as follows:
ICCard TestCard Operate SuccessPress Enter See Detail
Press Cancel Exit
ICCard Test
Operate IC Card%
ICCard Test
Card Not Present
MGCard Test
Please Swipe Card%
-
8/13/2019 POS530S User Manual-V1.1
12/35
10
SAM1 and SAM2 are corresponding separately with two SAM card slots. The screen shows
corresponding datas if the SAM card exists, keep pressing !ENTER",!UP"or !DOWN"key
to turn page for viewing the info. Exit with the !Cancel"key.
Note: The SAM Card slot is behind the battery; SAM Card can only be installed after the
battery is uploaded.
4.3.9 Battery
Check the current bettery power, voltage, current and temperature.
Choose !Battery" in API TEST mode and press !ENTER", the corresponding information
would be Displayed as follows,Press cancel to exit;
4.3.10 GPRS ModuleCheck whether GPRS conection is normal.
Choose"Module"in the API test mode and press !ENTER"to the !GPRS Test"interface.
If you already insert the sim card and the network is nomal, and corresponding configuration
in thegprs-connect-chatfile It will shows connect success
GPRS Test
Connect to GPRS%
Battery Test
Temperature: 27$
Battery TestVolume: 82%
Voltage: 7868mV
Current: 116mA
SAM Card Test1. SAM12. SAM2
-
8/13/2019 POS530S User Manual-V1.1
13/35
11
By the CANCEL key to return to the interface layer.
Note: N on behalf of signal i nteger value. N values range from 1 ~ 31, when N> 15 when
the signal i ndicates that the volume of a normal state, the greater the value, the better the
signal.
4.3.11 PINPADCheck whether the entered PIN code can calculate the PinBlock correctly.
Choose !PINPAD" in the API test mode to enter into !PINPAD Test" interface. Show as
follows:
Display a string of serial number, press !Enter", showing as follows:
Input the Pin number, press "Enter"to encrypt the Pin number.
4.3.12 Security
Check whether the security key is lost or not.
Choose !Security" in the API test mode, the screen shows !Security Diagno Passed" to
indicate the key is not lost, as follows:
The screen displays "SecurityBugFound"if the security key is lost.
Security Test
Security Diagno Passed
PINPAD TestEnter Password:
PINPAD TestPadSerial:
Pad10808111800001
GPRS Test
Connect success
Signal:N
-
8/13/2019 POS530S User Manual-V1.1
14/35
12
Note: Refer to Par t 5 to know how to download the key.
4.3.13 MifareCard ReaderCheck whether it can read and write the Mifare information correctly.
Select !MIFARECard"in the API TEST mode, the screen shows !No Card"when there is no
card or it is the non-Mifare card.
The corresponding Mifare Card information will be showed when the Mifare card is close to
the induction zone of POS.
Press !ENTER"to enter into the MIFARE card function menu, as follows:
!1"Select !Read"can read the MIFAREcard information. Press !ENTER"to the !MIFARE
Card Read"interface, as follows:
MIFARE card is divided into 16 reader sections, you can select corresponding section indexNo.(0-15) to read the certain information. Relative password need to be inputed after the
MIFARECard Test
No Card
MIFARE Card Read
BLOCK Index(0-15):
MIFARE Fun1. Read2. Write3. ChangeKey
MIFARECard Test
SerialLen:4Serial:
36 fb 4e b5
Security Test
Security Bug Found
-
8/13/2019 POS530S User Manual-V1.1
15/35
13
index number is inputed. As follows:
After inputing the correct 6-number password, press !ENTER" to read the certain
information, and press up-down and ENTER keys to turn page.
Press !CANCEL"to back to the the MIFARE card function menu.
!2"Select !Write"can wite data into the MIFARE card. Press !ENTER"to the !MIFARE
Card Write"interface, as follows:
Meantime, you can select the section to be wrote in by the index number; select the
corresponding section, press !ENTER"to the password input interface, as follows:
MIFARE Card Write
BLOCK Index(0-15):
MIFARE Card ReadBLOCK:1
38 39 31 32 33 34 35 36
MIFARE Card ReadBLOCK:131 32 33 34 35 36 37 38
39 31 32 33 34 35 36 37
MIFARE Card Read
Enter Key(6):
******
MIFARE Card ReadBLOCK Index(0-15):
1
MIFARE Card Write
BLOCK Index(0-15):
1
-
8/13/2019 POS530S User Manual-V1.1
16/35
14
After inputing the correct 6-number password, press !ENTER" to the data input interface,
and you can write the corresponding datas.
Input When the written data is less than 24 bytes, you need to re-input the password, press
!Cancel"key to cancel inputing.
Press !ENTER"after inputing the correct data, the following information will display:
Press !ENTER"when data-input goes wrong, the following error information will display:
!3"Choose !ChangeKey" can modify the r/w password in the corresponding section of
theMIFARE card; press !ENTER"to the !MIFARE ChangeKey"interface. As follows:
After inputing the certain section index number and press !ENTER", you need to input the
original password, as follows:
MIFARE ChangeKeyBLOCK Index(0-15):
1
MIFARE ChangeKey
BLOCK Index(0-15):
MIFARE Card WriteBLOCK:1
Request Error
MIFARE Card WriteBLOCK:1
Write Success
MIFARE Card Write
Enter Data(24):
MIFARE Card WriteEnter Key(6):
******
-
8/13/2019 POS530S User Manual-V1.1
17/35
15
Keep pressing !ENTER" after input the correct original password, you can input the new
password, as follows:
Input the new password, and press !ENTER", then you need re-input the new password, as
follows:
Press !ENTER"after re-inputing the password, if the passwords you inputed twice are the
same, the following information will display:
If the passwords you inputed twice are different, the following information will display:
4.3.14 RTCCheck whethe it can read and modify the present RTC correctly.
Choose RTC in the API TEST mode, and the present RTC will display. You can press the
!UP","DOWN"keys to modify the RTC. As follows:
MIFARE ChangeKey
New Key Different
MIFARE ChangeKeyBLOCK:1
Set Success
MIFARE ChangeKeyEnter New Key Again(6):
******
MIFARE ChangeKey
Enter New Key(6):
******
MIFARE ChangeKeyEnter Old Key(6):
******
-
8/13/2019 POS530S User Manual-V1.1
18/35
16
4.3.15 USB interfaceCheck whether the POS machine can detect the exchanger between the medium with USB
port and the POS normally.
First Connect the POS and PC with the special serial cable, and open the hyperterminal.
Insert the U-disk,
Choose USB in the API TEST mode to enter into the !USB Test"interface, as follows:
and wait for connecting until !USB Init Success"turns up.
Press !ENTER"to the !USB Config"interface.
Type !cd /mnt;ls"to enter into the mnt folder in the hyperterminal interface.
2008-01-01 00:18:18
USB Config1. Mount2. Umount
USB Test
USB Init Success
USB Test
USB Check%
-
8/13/2019 POS530S User Manual-V1.1
19/35
17
Select !1. Mount" in the USB config Menu on POS. It will display !USB Mount Success"
when the mapping relation is set up successfully between usb folder and U-disk. The files
can be transferred between U-disk and POS machine freely.
Type !cd usb"into the usbfolder under the root directory of the hyperterminal interface. You
can see the files under the root directory of the U-disk. Users can copy some of the files to
the /mnt/nand!to be transferred between U-disk and the POS machine.
USB Mount
USB Mount Success
-
8/13/2019 POS530S User Manual-V1.1
20/35
18
When umont the U-disk, you need exit the usb folder first in the hyperterminal interface, then
Select"2.Umount"on the USB Config menu, the !USB Umount Success"will turn up. Press
!Cancel"to exit the !USB Config"menu, the U-disk can be pulled out.
4.3.16 LogoCheck whether it can download and show the logo normally.
Relative file: Logo.bmp(12864 pixel)
Execute theDownloadForS530S.exeunder Windows, click !Add"to add the files required to
be burned; click !Start" to start the service waiting download.(Note: Don"t tick off the
DefaultLoad!item)
USB Umount
USB Umount Success
-
8/13/2019 POS530S User Manual-V1.1
21/35
19
1%Enter into the !System Mode"interface, and select !System Func".
2%Select !Application" in the !System Func" interface, and then select !Download" in the!Application"interface.
3%Enter in to the !Download Menu"interface, and select "Config"to set the corresponding IP
Application
1. Download
2. Delete
System Func
4. Application
System Func1. System Info2. Password3. Setup
System Mode
1. System Func2. API Test3. Serial Test
-
8/13/2019 POS530S User Manual-V1.1
22/35
20
address. The port setting should be the same with the one setted in
!DownloadForS530S.exe".
4%Press !Cancel" to back to the !Download Menu" interface, the POS will finish thedownloading automatically.
5%Download finished, display as follows:
After finish downdloading the logo, press !CANCEL" to return to the !System Mode"
interface and select the !API Test"option.
Enter into the !API Test"interface and select the !Logo"item.
Press !ENTER"to the !Logo Set"interface, as follows:
API Test
16. Logo
17. Sleep
Download
Download File%Finished
Download Menu1. Download
2. Config
System Mode
1. System Func2. API Test3. Serial Test
Server IP Address:
172.16.17.11Server Port:
8163
Download Menu1. Download
2. Config
-
8/13/2019 POS530S User Manual-V1.1
23/35
21
You can set the logo you download as the Start Logo by choosing the !DownloadLogo"
option. Press !ENTER"to the !DownloadLogo Test"option. Display as follows if succeed:
Choose the !DisplayLogo"option to display the current start logo. Press !ENTER"to display
the following:
4.3.17 SleepCheck whether the POS can enter into the standby power-down mode normally or not,
whether can be waken up normally.
Select !Sleep"in the API TEST mode option to enter into the !Sleep Test" interface. As
follows:
Select any key (except the power key and the Cancel key) according to the prompt on the
interface, the POS will be in the sleep mode. As follows:
Press any key to wake up the POS when it is in the sleep mode. As follows:
DownloadLogo Test
Download Logo Success
Logo Set1. DownloadLogo2. DisplayLogo
Sleep Test
POS in Sleep Mode
Sleep TestPress Any Key To
Send Sleep Command
-
8/13/2019 POS530S User Manual-V1.1
24/35
22
4.4 User serial port testCheck whether the POS can communicate with the PC by the serial port.
Connect the POS and the PC with a special line, open the hyperterminal on the PC , and start
the POS, keep pressing the combination keys !Fn+2"until the "system password:"turns up,
and then input the password.
Input the relevant password and press !ENTER" to enter into the !System Mode"
interface.Select the !Serial Test"option.
Press !ENTER"to enter into the !Serial Test"interface, as follows:
Now, press any key on the POS, you can see the corresponding key-press from the PC
terminal.
System Mode1. System Func2. API Test
3. Serial Test
Serial Test
Enter any key to serial%
system password:
*****************
Sleep Test
POS Is Wakeup
-
8/13/2019 POS530S User Manual-V1.1
25/35
23
Note: the setting of hyperterminal on the PC is (baud rate 115200, date bit 8, stop bit 1, no
oddeven pari ty bit, hardware flow control to close)
First press!CANCEL+1"on the keybord of the POS. Then the corresponding key-press will
be displayed on the screen of the POS when you press any key.
Press !CANCEL+2"keys on the keybord to exit the !Serial Test"
4.5 Phone TestCheck whether the Phone is normal
Insert SIM card and press Power Key to turn on the POS, presss "Fn+2"until appear"system
password:",input the password to enter into !System Mode"then select the !Phone Test"
interface. As follows:
Serial Test End!
Exit after 5 second!
Abcdefghijklmnopqrstuvwxyz
-
8/13/2019 POS530S User Manual-V1.1
26/35
24
Then select the menu 4 into the Phone test process, if connect normal,you will see
Then you can Press enter into dial menu
Enter the phone nuber to dial,Press Cancel for two second to exit
5. Program Update
5.1 Kernel Update
Relative files: rootfs.img(root file)%uImage(kernel)%u-boot.bin(bootloader)
!1"Start TFTPservice under Windows, connect the POS and the PC with special lan and
serial cable.
!2"Start the hyperterminal, and then when the POS is started keep pressing the !space"key
promtly until the U-boot> interface turns up.
!3"Input theprintenvcommand to check the current setting information..
Phone FunPhone Number:
Phone Fun
Welcome ToUse Sunyard Phone
System Mode
4. Phone Test
-
8/13/2019 POS530S User Manual-V1.1
27/35
25
The relevat settings can be modified by thesetenv command. You can save the settings with
saveenvafter finished the settings. For example:
a) setenv serverip 172.16.17.11 //set the IP of the tftp serverb) setenv ipaddr 172.16.17.177 //set the IP of the POSc) setenv netmask 255.255.255.0 //set the subnet mask of the POSd) setenv gateway 172.16.17.1 //set the gateway of the POSe) saveenv //save the settings
(4) Input the command !download", the !Download Menu"will be displayed.
-
8/13/2019 POS530S User Manual-V1.1
28/35
26
Update the system file, input 1 in the terminal; update the kernel, input 2; update the U-boot,input 3; displays the following format means can download normally; otherwise, please
check the network communication between the POS and the server.
Input 1, display as follows:
Input 2, display as follows:
-
8/13/2019 POS530S User Manual-V1.1
29/35
27
Input 3, display as follows:
Input 4, display as follows:
5.2 Download the keyIf you want to use the POS machine regularly when the key is lost, you must download the
key, do as the followings:
!1"Start the POS, keep pressing the combination keys !Fn+2" until !system password:"
-
8/13/2019 POS530S User Manual-V1.1
30/35
28
turns up, then input the password.
(2)Enter into the !System Mode"interface, and select !API Test".
(3) Enter into the !API Test"interface, and select the 12thitem.
(4)Press !ENTER"to enter into the !Security Test"interface, displayed as follows:
(5) Re-press the !ENTER$", displayed as follows:
(6) Connect the POS and PC with a special cable, and use the 530KeyDownload.exe software
to select the relevant COM port, click to start download.
System Mode
1#System Func2#API Test3#Serial Test
Security Test
Wait Download%
Security Test
Security Bug Found
system password:
*****************
API Test10.GPRS11.PINPAD
12.Security
-
8/13/2019 POS530S User Manual-V1.1
31/35
29
(7)When key download is finished, the POS screen will display:
(8)To run DEMO program normally after finishing downloading the key, you need to select
!Set Parameter"option after starting the DEMO program.
(9)Pres !ENTER" to enter into the !Set Parameter" interface, then select !Master Key"
option.
(10)Press !ENTER"to select the key interface. (The system default is the 9thone)
Set Parameter1. Host Parameter2. Master Key
Main Menu1. Sale2. Trans Detail3. Set Parameter
Security Test
Download Success
-
8/13/2019 POS530S User Manual-V1.1
32/35
30
(11)Press !ENTER"to set the key (16 bits):
(12)Press !ENTER", if succeed, display as follows:
5.3 Download the Font libRelative file: vector.ttf
Execute !DownloadForS530S.exe"under Windows&click !Add"to add the files required to
be burned; click !Start" to start the service waiting download.(Note: Don"t tick off the
DefaultLoad!item)
Load Key
Insert Key Success!
Next Key?
Load Key
Key Index(0-9):9
Load Key
Key Index(0-9):9Enter Key:
****************
-
8/13/2019 POS530S User Manual-V1.1
33/35
31
Start the POS, keep pressing the combination keys !Fn+2" until the !system password:"
turns up, and input the password.
Enter into the !System Mode"interface, and select !System Func".
Select !Application" in the !System Func" interface, and then select !Download" in the
!Application"interface.
System Func1. System Info2. Password
3. Setup
System Mode1. System Func2. API Test
3. Serial Test
system password:
*****************
-
8/13/2019 POS530S User Manual-V1.1
34/35
32
Enter in to the !Download Menu"interface, and select "Config"to set the corresponding IP
address. The port setting should be the same with the one setted in !DownloadForS530S.exe".
Press !Cancel" to back to the !Download Menu" interface, the POS will finish the
downloading automatically.
Download finished, displaying as follows:
5.4 Download the configuration files of the wireless moduleIf you want to use the wireless module of the POS, you should download the relative
configuration files: gprs-connect-chat, gprs-disconnect-chat. Refer to 5.3 Download the Font
Download
Download File%
Finished
Download Menu1. Download
2. Config
Server IP Address:172.16.17.11
Server Port:8163
Download Menu1. Download
2. Config
Application1. Download
2. Delete
System Func
4. Application
-
8/13/2019 POS530S User Manual-V1.1
35/35
to get the download method.