porv-mr...• fire tested to en iso 6182-5:2006 • lloyd’s & abs type approvals designed for...
TRANSCRIPT
Dorot Fire Protection Division
Deluge Valves
Deluge Valves
Certification & compliance by design
Typical applications
Automatic or Manual actuated Fire Suppression Systems
Hangars & Airport terminals
Flammable Storage
Power Generation, Transformer & Transmission Plants
Tunnels
Petrochemical, Oil & Gas Installations
CAMERA-READY LOGOTYPE FOR TYPE L AND TYPE R LISTING MARKSThese Marks are registered by Underwriters Laboratories Inc.
The minimum height of the registered trademark symbol ® shall be 3/64 of an inch. When the overall diameter of the UL Mark is less than 3/8 of an inch, the trademark symbol may be omitted if it is not legible to the naked eye.
The font for all letter forms is Helvetica Condensed Black, except for the trademark symbol ®, which isHelvetica Condensed Medium. No other fonts are acceptable.
Please Note:The word "MARINE" should only be used for UL Classified marine products.
200-195D 20M/11/97
Onshore-offshore
Mining
Model 68 DE\ PORV-MR
Pneumatically Actuated, Manual-Reset Deluge Valve
• ANSI FCI 70-2 Class VI seat leakage class• UL listed under VLFT category• Fire tested to EN ISO 6182-5:2006• Lloyd’s & ABS type approvals
Designed for• High-pressure (PN25/375psi), high-flow deluge
systems• Automatic or local manual emergency actuation• Hazardous-flammable and explosion classified
area fire suppression• Onshore & Offshore, Naval, Industrial, Commercial
& Residential fire suppression
Features• Superior design featuring exceptionally low
pressure losses at high flow rates• Low to negligible lifelong maintenance costs
thanks to no wetted metallic and mechanical moving parts design
• Simple, comprised of 3 main parts, no expertise required for maintenance
• Fresh or Brackish water, seawater and foam• Out of box fully assembled & tested valves• All valves are factory trimmed for both vertical &
horizontal installations without modification• Extensive valve & trim materials selection and
corrosion protection coating to EN12944 C4, C5 & C5M
1
Deluge Valve
Model 68 DE\PORV-MR
2
Manually Actuated
Standby Position Pneumatically Actuated
Reset to Close
General description and operation modes
This pneumatically actuated, manual-reset deluge valve is designed for fire protection systems controlled and actuated by an air or Gas dry pilot-line. The basic control valve type used in this deluge system is a direct-sealing elastomeric diaphragm, hydraulically operated control valve engineered specifically for fire protection systems.In the standby position, the deluge valve is held closed by the upstream water pressure, trapped in the valve's control chamber. The water pressure enters the control chamber through the priming line ball valve [2], a Y-Type strainer [3], a check valve [4] and a DMR (Dorot Manual Reset latching device) [5].Under fire conditions, one (or more) of the automatic sprinklers on the dry (pneumatically-pressurized) pilot-line burst. The pressure in the relay valve [9] drops, causing it to open and allowing the water to drain from the deluge valve’s control chamber. The deluge valve opens instantly and allows water to flow into the pipeline and through the open sprinklers over the protected area.Manual emergency actuation is enabled by opening the emergency manual activation valve [6]. The deluge valve opens instantly and allows water to flow into the pipeline and through the open sprinklers over the protected area.When the valve trips open, the DMR [5] isolates the control chamber from the upstream pressure source. Reconnecting the upstream pressure to enable the deluge valve to close can only be achieved by pressing the DMR’s [5] knob.Resetting, maintenance and periodic testing instructions must be followed as described in detail in the relevant Dorot DE\PORV-MR model's IOM (Installation, Operation & Maintenance) manual.
68-DE\PORV-M
R
68-DE\PORV-M
R
68-DE\PORV-M
R
68-DE\PORV-M
R
Water Water
Supervisory Pressure Source
Pilot-Line
To System
Pilot-Line
Pilot-Line
Water To System
Pilot-Line
Water
Press
Supervisory Pressure Source
Supervisory Pressure Source
[6]
[1]
[9]
[2] [3] [4][5]
[6]
[1]
[9]
[2] [3] [4][5]
[6]
[1]
[9]
[2] [3] [4][5]
[6]
[1]
[9]
[2] [3] [4] [5]
Supervisory Pressure Source
Deluge Valve
Model 68 DE\PORV-MR
3
7
1
2
3
4
8
2
4 5
8
9
6
7
1
2
3
4
8
2
4 5
8
9
6
68-DE\PORV-MR
ID Description1 S-68 Control Valve2 Ball Valve3 Y Control Filter4 Check Valve5 Dorot Latching & Manual Reset device6 Emergency manual activation Valve7 1/2" Drip Valve8 Pressure Gauge9 662UL Relay Valve
Typical control trim materials
ID Description Standard POG (1) Applications
1 Valve body See Series 100 Engineering data (2)
2 Ball valve Brass \ SST ball SST316
3 Y-Type strainer Brass \ SST screen SST316
4 Check valve Brass SST316
5 DMR (manual-reset device) Brass SST316
6 Manual emergency valve Brass SST316
7 Drip valve Brass SST316
8 Pressure gauge Brass case \ SST connection SST316
9 66-2UL relay Brass SST316
(1) Petrochemical, Oil & Gas(2) Refer to material selection guidelines,
Engineering Data - Materials:Ductile Iron A-536 65-45-12;Cast Steel A-216 WCB;Cast Steel A-352 LCB;Austenitic Stainless-Steel A-351/CF8M;Super Duplex 2507;Nickel-Aluminum-Bronze B-148 UNS C95800
Deluge Valve
Model 68 DE\PORV-MR
4
General arrangement and valve dimensions
Valve 2 (50) 2.5 (65) 3 (80) 4 (100) 6 (150) 8 (200) 10 (250)inch mm inch mm inch mm inch mm inch mm inch mm inch mm
A 95/8 243 93/16 233 123/16 310 14 356 173/16 436 207/8 530 25 635AG(1) 95/8 243 10 253 133/16 336 15 380 175/16 440 217/8 556 N/A
B 65/8 168 73/8 185 77/8 200 93/8 238 121/8 306 143/16 360 167/8 430C 35/8 91 35/8 91 85/16 210 37/8 98 73/8 189 8 203 1011/16 271D 77/8 201 77/8 201 77/8 201 77/8 201 77/8 201 77/8 201 913/16 249E 10 255 10 255 125/8 321 121/2 317 1511/16 400 161/2 420 173/8 443F 101/2 266 101/2 266 105/16 262 105/16 262 105/16 262 103/8 265 121/2 317
Approx. Weight
Ibs kg Ibs kg Ibs kg Ibs kg Ibs kg Ibs kg Ibs kg35 16 35 16 77 35 95 43 176 80 282 128 430 195
* Dimensions are approximate(1) Grooved model length
CONTROL VALVES
SST
190
CONTROL VALVES
Brass
247
CONTROL VALVES
E
B
DC
F
A
DE-PORV-MR
CONTROL VALVES
E
B
DC
F
A
DE-PORV-MR
CONTROL VALVES
E
B
DC
F
A
DE-PORV-MR
Optional Upstream Drain Valve
Deluge Valve
Model 68 DE\PORV-MR
5
1
DMR
3
2
4
Typical system layoutDorot’s DE\PORV-MR, pneumatically actuated, manual-reset deluge valve, is held shut drip-tight in its standby position. When one (or more) of the automatic sprinklers on the pilot-line burst, the pressure in the relay valve drops, allowing water to drain from the deluge valve’s control chamber. The DMR latches the deluge valve open, allowing water to flow into all of the open sprinklers over the protected area.
DMR (latching manual-reset device)3
Pneumatically actuated, manual-reset deluge valve
1
PPCS (Pneumatic pressure control system)
2
Pneumatic pilot line4
Deluge Valve
Model 68 DE\PORV-MR
Ordering guide
Ed
itio
n 1
2.20
19
Dorot & Dorot companies worldwide reserve the right to make changes without notice including product specification and configuration, content, description(s), dimensions etc. The Information herein is subject to change without notice. Dorot shall not be held liable for any errors. All rights reserved. © Copyright by Dorot.6
Specification for engineers The deluge valve shall be hydraulically operated, direct elastomeric diaphragm-seal, single chamber weir type. The valve shall consist of three major components: the body, cover and the diaphragm assembly. The diaphragm shall be the only moving part. The diaphragm forms a sealed control chamber in the upper portion of the valve, separating operating pressure from line pressure. Packing glands’ stuffing boxes and dynamic o-ring seals are not permitted and there shall be no shafts, discs, bearings or pistons operating the main valve. No hourglass-shaped disc retainers shall be permitted and no V-type, U-type or other slotted type disc guides shall be used. The valve shall contain a nylon reinforced rubber diaphragm, elastic & resilient through its entire surface without vulcanized radial discs and/or reinforcements. The diaphragm shall not be guided by any shafts or bearings and shall not be in close contact with other valve parts except for its sealing surface. Maintenance, disassembly and reassembly of all the valve’s components shall be made possible on site and in-line, without the need to remove the valve from the line. Standard material valves such as Ductile Iron (ASTM A-536 65-45-12) and Cast Steel (WCB A-216) should be coated with high-built fusion-bonded epoxy (FBE) and a UV protective topcoat conforming to EN12944 C4 & C5 high & very high corrosivity protection grades. Naval quality/very high corrosivity protection grade conforming to EN12944 C5M is available upon request. Other coating standards such as NORSOK or ANSI/NACE as well as coatings for special material valves such as austenitic Stainless Steel (CF8M/ASTM A-316 ) and Nickel Aluminum Bronze (ASTM B-148) can be supplied upon request. The valve should be UL listed under category VLFT for fire protection service.
Dorot Control Valves www.dorot.come-mail: [email protected]
68 P SS - 3 - AN15RF - DE\PORV\MR - S - PI-HA-...
Model 68 68 Optional add-on
Optional add-on PI Pressure switch
Spring P HA Alarm test trim
Position Indicator I UV Upstream drain valve
Material LS Limit-proximity switch
Ductile Iron Ex Explosion-proof
Cast Steel CS Trim
CF8M (SST316) SS Brass-Copper
Ni-Al-Br NAB S Stainless Steel 316
Size (inch) 2”-24” X Other
Control function
End connection standard
AN15RF ANSI #150 (FF or RF)
AN30RF ANSI #300 (FF or RF)
GRV Grooved
ISO PN16 ISO PN16
ISO PN25 ISO PN25
xxx Other (specify)
Pressure rating:• 250 psi for Class #150• 375 psi for Class #300
Please specify in addition to the above:• Electrical features other than standard (24VDC, IP65/NEMA4)• If explosion-proof accessories are required such as solenoids,
pressure switches, etc., please define classification.• Control trim material other than standard• Required standards, certifications and approval Standard- leave empty
Ordering example: 68PSS-3-AN15RF-DE\PORV\MR-S-PI-HA
Technical data:• Media up to 80°C = 176°F• Elastomers suitable for extreme climates are
available upon request.
Sizes:• Straight Flow: 2”-24”• Angle: 1.5” - 8”
UL listed sizes:• Model 68: 2”-10”
End connections:• Flanged:
ISO PN10, ISO-PN16 & ISO-PN25 ANSI B16.42 Class # 150 and # 300 AS Tables D & E, JIS Additional options available upon request
• Grooved: Sizes: 2”-8”