popular size range ½ to 1½ hp, available in corrosion...
TRANSCRIPT
X-Factor Series LXFILTERS AND NEUTRALIZERS
ACID NEUTRALIZERS, FILTERSLancaster’s acid neutralizers correct low pH water, which in turn protects your pipes, faucets, heaters, boilers and all appliances requiring the use of water. A water softener may also be recommended to remove hardness.
SEDIMENT/TURBIDITY (FILTER-AG)Lancaster’s sediment filters will remove dirt, silica, and most suspended matter from your water supply down to a 20 micron filtering level. Filter AG requires no chemical regenerents - just a simple, periodic backwash.
CARBON FILTERSLancaster’s carbon filters, through filtration and adsorption, remove organic chemicals and other contaminants which cause color, taste and odor problems.
IRON FILTERS; BIRM & MTMLancaster’s iron filters remove iron and manganese, also filter other suspended matter, prevent rust stains on clothing, appliances and remove taste and color of iron. When sulfur is present, MTM is the recommended mineral.
Model Number Tank Service GPM Backwash GPM
Color, Taste & Odor (Carbon) Filters Cont. Peak
7-LXCT-1B 10x44 5 8 6.5
7-LXCT-2B 13x48 7 9 10
7-LXCT-3B 14x65 10 12 10
Acid Neutralizer (Calcite) Filters
7-LXDAN-1B 10x47 (with dome plug) 5 8 6.5
7-LXDAN-1.5B 10x54 (with dome plug) 6 9 6.5
7-LXDAN-2B 13x48 (with dome plug) 7 10 10
7-LXDAN-3B 13x65 (with dome plug) 10 12 10
Sediment/Turbidity (Filter AG) Filters
7-LXST-1B 10x44 5 8 5.3
7-LXST-2B 13x48 7 9 9
7-LXST-3B 14x65 10 12 9
Iron (Birm) Filters
7-LXIM-1B 10x44 5 8 6.5
7-LXIM-2B 13x48 7 9 10
7-LXIM-3B 14x65 10 12 10
Iron (MTM) Filters
7-LXTPIM-1B 10x44 5 8 6.5
7-LXTPIM-2B 13x48 7 9 11
7-LXTPIM-3B 14x65 10 12 11
Note: When using Birm for iron removal, it is necessary that the water contain no oil or hydrogen sulfide, organic matter not to exceed 4-5ppm, the D.O. content equal at least 15% of iron content with a pH of 6.8 or more. If the influent water has a pH of less than 6.8, neutralizing additives such as calcite, corosex or soda ash may be used prior to the Birm filter to raise the pH. A water having a low D.O. level may be pretreated by aeration. Chlorination greatly reduces Birm’s activity. High concentrations of the chlorine compounds may deplete the catalytic coating.
WAT E R T R E AT M E N TLANCASTER •
www.LancasterWaterTreatment.com • 1-800-442-0786May 2016
DIAMOND LINE LX
– FILTERS & NEUTR
ALIZERS
www.LancasterPump.com • 1-800-442-0786
LANCASTERLANCASTER
SURV
IVO
R SERIES
SURVIVOR 4” SUBMERSIBLE PUMP MODEL NUMBER BREAKDOWN
Survivor 4” Submersible Pumps
2-2LST5007-2Catalog Section
Number of Stages
1 = 115 Volt, Single Phase 2 = 230 Volt, Single Phase 3 = 230 Volt, Three Phase (Additional Voltages Available)
2 = 2 Wire 3 = 3 Wire
P = Plastic Discharge Head Plastic Motor Support
L = Lancaster Hydro-Force Motor (no letter L) = Franklin Electric Motor
S = Stainless Steel Discharge Head Stainless Steel Motor Support
SP = Stainless Steel Discharge Head Plastic Motor Support
J = 5 GPM L = 7 GPM
T = 10 GPM U = 15 GPM
W = 22 GPM
50 = 0.50 HP 75 = 0.75 HP 100 = 1.0 HP 150 = 1.5 HP 200 = 2.0 HP 300 = 3.0 HP 500 = 5.0 HP
Lancaster Pump offers a broad selection of SURVIVOR 4” submersible well pumps. Horsepower from ½ to 5 HP, with the most popular size range ½ to 1½ HP, available in Corrosion-Resistant Thermoplastic or Super Strength Stainless Steel. Capacity ratings are 5, 7, 10, 15 and 22 gallons per minute with heads as high as 990 feet.
INSIDE A PUMP STAGE• Diffuser with stainless steel seal/wear surfaces for upper impeller hub
• Impeller eye surrounding lower hub
• Stage plate with stainless steel seal/wear surface for impeller eye
ASSEMBLED PUMP STAGE• Laminated phenolic thrust washer on top of every stage provides
down-thrust protection and axial sealing for the impeller inside the next stage above
BREAKDOWN• Glass-filled Noryl® Discharge Head with field replaceable fluted
Internal Check Valve. Molded jug handles - no need for safety cable adapter, ½ HP thru 1½ HP models. Available in Stainless Steel up to 5 HP.
• Fluted Polyurethane Bearing at top end of shaft. Excellent abrasion and wear resistance.
• Stainless Steel Cable Guard for maximum cable protection. Attached with stainless steel screws.
• Balanced Teflon® impregnated Impellers made of glass-filled thermoplastic, provide for lower friction for longer pump life.
• Stainless steel Hex Shaft with slotted end for test turning.
• Fully enclosed, glass-filled thermoplastic Diffusers and Stage Plates with stainless steel wear surfaces. Each stage is complete with an individual composite thrust washer for extra protection.
• Heavy wall, high quality Stainless Steel Pump Casing sized inside for perfect stage alignment.
• Glass-filled Noryl® Motor Support ½ HP thru 1 ½ Hp models. Available in Stainless Steel up to 5 HP.
• Stainless Steel screen, cannot snap off during installation.HP System Number Power Supply Input VFD
EnclosureInlet (FPT)
Outlet (MPT)
23-906B-3-T2-V21-N1-SX 208/240 VAC Single Phase NEMA 1
1.5 23-906B-3-T2-V21-N3R-SX 208/240 VAC Single Phase NEMA 3R
33-908B-3-T3-V21-N1-SX 208/240 VAC Single Phase NEMA 1
2 23-908B-3-T3-V21-N3R-SX 208/240 VAC Single Phase NEMA 3R
53-909B-3-T5-V23-N1-SX 208/240 VAC Three Phase NEMA 1
2 2.53-909B-3-T5-V23-N3R-SX 208/240 VAC Three Phase NEMA 3R
7.5
3-910B-3-T7-V23-N1-SX 208/240 VAC Three Phase NEMA 12 2.5
3-910B-3-T7-V23-N3R-SX 208/240 VAC Three Phase NEMA 3R3-910B-3-T7-V43-N1-SX 480 VAC Three Phase NEMA 1
2 2.53-910B-3-T7-V43-N3R-SX 480 VAC Three Phase NEMA 3R
Model Number Breakdown can be found online (pg.3)Custom system can be sized upon request
LANCASTERLANCASTER
SURV
IVO
R SERIES
SURVIVOR 4” SUBMERSIBLE PUMP MODEL NUMBER BREAKDOWN
Survivor 4” Submersible Pumps
2-2LST5007-2Catalog Section
Number of Stages
1 = 115 Volt, Single Phase 2 = 230 Volt, Single Phase 3 = 230 Volt, Three Phase (Additional Voltages Available)
2 = 2 Wire 3 = 3 Wire
P = Plastic Discharge Head Plastic Motor Support
L = Lancaster Hydro-Force Motor (no letter L) = Franklin Electric Motor
S = Stainless Steel Discharge Head Stainless Steel Motor Support
SP = Stainless Steel Discharge Head Plastic Motor Support
J = 5 GPM L = 7 GPM
T = 10 GPM U = 15 GPM
W = 22 GPM
50 = 0.50 HP 75 = 0.75 HP 100 = 1.0 HP 150 = 1.5 HP 200 = 2.0 HP 300 = 3.0 HP 500 = 5.0 HP
Lancaster Pump offers a broad selection of SURVIVOR 4” submersible well pumps. Horsepower from ½ to 5 HP, with the most popular size range ½ to 1½ HP, available in Corrosion-Resistant Thermoplastic or Super Strength Stainless Steel. Capacity ratings are 5, 7, 10, 15 and 22 gallons per minute with heads as high as 990 feet.
INSIDE A PUMP STAGE• Diffuser with stainless steel seal/wear surfaces for upper impeller hub
• Impeller eye surrounding lower hub
• Stage plate with stainless steel seal/wear surface for impeller eye
ASSEMBLED PUMP STAGE• Laminated phenolic thrust washer on top of every stage provides
down-thrust protection and axial sealing for the impeller inside the next stage above
BREAKDOWN• Glass-filled Noryl® Discharge Head with field replaceable fluted
Internal Check Valve. Molded jug handles - no need for safety cable adapter, ½ HP thru 1½ HP models. Available in Stainless Steel up to 5 HP.
• Fluted Polyurethane Bearing at top end of shaft. Excellent abrasion and wear resistance.
• Stainless Steel Cable Guard for maximum cable protection. Attached with stainless steel screws.
• Balanced Teflon® impregnated Impellers made of glass-filled thermoplastic, provide for lower friction for longer pump life.
• Stainless steel Hex Shaft with slotted end for test turning.
• Fully enclosed, glass-filled thermoplastic Diffusers and Stage Plates with stainless steel wear surfaces. Each stage is complete with an individual composite thrust washer for extra protection.
• Heavy wall, high quality Stainless Steel Pump Casing sized inside for perfect stage alignment.
• Glass-filled Noryl® Motor Support ½ HP thru 1 ½ Hp models. Available in Stainless Steel up to 5 HP.
• Stainless Steel screen, cannot snap off during installation.
VA
RIOSPEED
® C
ON
STAN
T PRESSURE BOO
STER SYSTEM - SIM
PLEX
VARIOspeed® Constant Pressure Booster System - SimplexAdvanced solutions for providing constant water pressure.Lancaster Pump’s VARIOspeed® Simplex Constant Pressure Booster Systems are simple to install and simple to maintain for larger residential and commercial applications where elevation is a concern or sufficient main pressure is not available. Their space sensitive design includes a wide capacity range from 10 to 150 GPM. The VARIOspeed® Controller regulates the speed of the pump to precisely match system demand, decreasing energy usage and allowing for reduced tank size.
For duplex systems with alternation and lead/lag operations, consult your distributor or our factory.
SYSTEM INCLUDES:• UL/cUL listed VARIOspeed® Control using a factory-
programmed Variable Frequency Drive (VFD) in a NEMA 1 or NEMA 3R enclosure
• Horizontal Close Coupled End Suction Centrifugal Pump• TEFC Motor - standard• Diaphragm Tank• Tank Cross Manifold for pressure gauge, transducer, relief
valve, and hose bib• Variable Flow Demand Check Valve• Enamel Coated Steel Base and Frame
FEATURES & BENEFITS:• Provides constant water pressure.• Energy Efficient: using notably less electricity than
conventional centrifugal pump applications as the drive will automatically adjust the pump speed to match lower demand conditions.
• Factory assembled, wired and tested for simple startup.• Check valve specially designed with additional poppet
stem stability to handle both low and high flow conditions associated with VFD applications without chatter/noise.
• Breakthrough diagnostics and system protection foreasy service and maintenance
X-Factor Series LXFILTERS AND NEUTRALIZERS
ACID NEUTRALIZERS, FILTERSLancaster’s acid neutralizers correct low pH water, which in turn protects your pipes, faucets, heaters, boilers and all appliances requiring the use of water. A water softener may also be recommended to remove hardness.
SEDIMENT/TURBIDITY (FILTER-AG)Lancaster’s sediment filters will remove dirt, silica, and most suspended matter from your water supply down to a 20 micron filtering level. Filter AG requires no chemical regenerents - just a simple, periodic backwash.
CARBON FILTERSLancaster’s carbon filters, through filtration and adsorption, remove organic chemicals and other contaminants which cause color, taste and odor problems.
IRON FILTERS; BIRM & MTMLancaster’s iron filters remove iron and manganese, also filter other suspended matter, prevent rust stains on clothing, appliances and remove taste and color of iron. When sulfur is present, MTM is the recommended mineral.
Model Number Tank Service GPM Backwash GPM
Color, Taste & Odor (Carbon) Filters Cont. Peak
7-LXCT-1B 10x44 5 8 6.5
7-LXCT-2B 13x48 7 9 10
7-LXCT-3B 14x65 10 12 10
Acid Neutralizer (Calcite) Filters
7-LXDAN-1B 10x47 (with dome plug) 5 8 6.5
7-LXDAN-1.5B 10x54 (with dome plug) 6 9 6.5
7-LXDAN-2B 13x48 (with dome plug) 7 10 10
7-LXDAN-3B 13x65 (with dome plug) 10 12 10
Sediment/Turbidity (Filter AG) Filters
7-LXST-1B 10x44 5 8 5.3
7-LXST-2B 13x48 7 9 9
7-LXST-3B 14x65 10 12 9
Iron (Birm) Filters
7-LXIM-1B 10x44 5 8 6.5
7-LXIM-2B 13x48 7 9 10
7-LXIM-3B 14x65 10 12 10
Iron (MTM) Filters
7-LXTPIM-1B 10x44 5 8 6.5
7-LXTPIM-2B 13x48 7 9 11
7-LXTPIM-3B 14x65 10 12 11
Note: When using Birm for iron removal, it is necessary that the water contain no oil or hydrogen sulfide, organic matter not to exceed 4-5ppm, the D.O. content equal at least 15% of iron content with a pH of 6.8 or more. If the influent water has a pH of less than 6.8, neutralizing additives such as calcite, corosex or soda ash may be used prior to the Birm filter to raise the pH. A water having a low D.O. level may be pretreated by aeration. Chlorination greatly reduces Birm’s activity. High concentrations of the chlorine compounds may deplete the catalytic coating.
WAT E R T R E AT M E N TLANCASTER •
www.LancasterWaterTreatment.com • 1-800-442-0786May 2016
DIAMOND LINE LX
– FILTERS & NEUTR
ALIZERS
www.LancasterPump.com • 1-800-442-0786
LANCASTERLANCASTER
4” ENCAPSULATED SUBMERSIBLE MOTORS
SINGLE PHASE TWO-WIRE (½ - 1½ HP, 230V) & THREE-WIRE (½ - 1 HP, 230V)
EQUIPPED WITH LIGHTNING ARRESTORS
TECHNICAL FEATURES
TWO-WIRE DESIGN• Split-phase induction run (IR) design with built-in electronic starter connected
in series to a high resistance auxiliary start winding – no capacitor required – electronic starter controls disengagement of start winding as a function of starting time and starting voltage.
THREE-WIRE DESIGN• Capacitor-start induction run (CSIR) design – control box required.
• Control box quick-disconnect design disconnects control box components from the electrical system when the lid is removed – will retrofit F.E. Q-D control boxes of same HP and voltage.
• Control box components include a 230V voltage relay for easy installation, two ground terminals, cable terminals up to AWG 8, and a start capacitor for higher starting torque.
• Control box painted steel enclosure with multiple knockouts is rated NEMA 3R for indoor or outdoor installation.
TWO-WIRE AND THREE-WIRE DESIGNS• Stator filled with special epoxy resin and hermetically sealed for a better insulation
of the winding and a greater heat exchange.
• Rotor and thrust bearings lubricated by water mixed with Propylene Glycol.
• Built-in check valve for restoring of cooling liquid (well water) as needed.
• Built-in lightning arrestors providing surge protection.
• Built-in automatic reset overload providing thermal (overheat) protection caused by high amperage and/or inadequate motor cooling.
• AISI 304 Stainless Steel motor frame shell, stator ends and liner, hermetically sealed for maximum corrosion resistance.
• AISI 303 Stainless Steel splined shaft end.
• Cationic epoxy electrocoated G20 cast iron top and bottom end brackets.
• AISI 304 Stainless Steel top and bottom end bracket covers.
• Shaft sealing system using labyrinth seal, sand slinger and lip seal.
• Pressure equalizing diaphragm.
• 4” NEMA flange.
• M8 threaded mounting studs.
• Removable plug-in lead cable.
• Degree of protection: IP68.
• Insulation: Class B.
• Time Rating: Continuous Duty.
• UL recognized component.
• UL classified water quality system component in accordance with ANSI/NSF 61 (health effects) and 372 (lead content).
FRANKLIN: Lancaster Pump is also teamed up with Franklin Electric’s 4” super stainless and high thrust submersible motors, delivering high quality and dependable service.
LANCASTER HYDRO-FORCE™
SURV
IVO
R SE
RIE
S
• Corrosion-resistant stainless steel exterior
• Stainless steel splined shaft
• Hermetically-sealed windings
• Filter check valve
• Water lubrication
• Kingsbury-type thrust bearing
• Pressure-equalizing diaphragm
• Built-in lightning arrestors (All single-phase, super stainless 200 & 230V three-phase)
• Removable water bloc lead
• UL Recognized and CSA certified component
• ANSI/ NSF 61 certified
• Industry standard NEMA mounting dimensions
VARIOspeed® Constant Pressure Booster System - Simplex60 to 40Hz Performance Curves - based upon clean cold water, 1.0 SP GR
Models: 3-909B-3-T5-V23-N1-SX 3-909B-3-T5-V23-N3R-SX
Models: 3-910B-3-T7-V23-N1-SX 3-910B-3-T7-V23-N3R-SX 3-910B-3-T7-V43-N1-SX 3-910B-3-T7-V43-N3R-SX
Models: 3-906B-3-T2-V21-N1-SX 3-906B-3-T2-V21-N3R-SX
Models: 3-908B-3-T3-V21-N1-SX 3-908B-3-T3-V21-N3R-SX
LANCASTERLANCASTER
SURV
IVO
R SERIES
SURVIVOR 4” SUBMERSIBLE PUMP MODEL NUMBER BREAKDOWN
Survivor 4” Submersible Pumps
2-2LST5007-2Catalog Section
Number of Stages
1 = 115 Volt, Single Phase 2 = 230 Volt, Single Phase 3 = 230 Volt, Three Phase (Additional Voltages Available)
2 = 2 Wire 3 = 3 Wire
P = Plastic Discharge Head Plastic Motor Support
L = Lancaster Hydro-Force Motor (no letter L) = Franklin Electric Motor
S = Stainless Steel Discharge Head Stainless Steel Motor Support
SP = Stainless Steel Discharge Head Plastic Motor Support
J = 5 GPM L = 7 GPM
T = 10 GPM U = 15 GPM
W = 22 GPM
50 = 0.50 HP 75 = 0.75 HP 100 = 1.0 HP 150 = 1.5 HP 200 = 2.0 HP 300 = 3.0 HP 500 = 5.0 HP
Lancaster Pump offers a broad selection of SURVIVOR 4” submersible well pumps. Horsepower from ½ to 5 HP, with the most popular size range ½ to 1½ HP, available in Corrosion-Resistant Thermoplastic or Super Strength Stainless Steel. Capacity ratings are 5, 7, 10, 15 and 22 gallons per minute with heads as high as 990 feet.
INSIDE A PUMP STAGE• Diffuser with stainless steel seal/wear surfaces for upper impeller hub
• Impeller eye surrounding lower hub
• Stage plate with stainless steel seal/wear surface for impeller eye
ASSEMBLED PUMP STAGE• Laminated phenolic thrust washer on top of every stage provides
down-thrust protection and axial sealing for the impeller inside the next stage above
BREAKDOWN• Glass-filled Noryl® Discharge Head with field replaceable fluted
Internal Check Valve. Molded jug handles - no need for safety cable adapter, ½ HP thru 1½ HP models. Available in Stainless Steel up to 5 HP.
• Fluted Polyurethane Bearing at top end of shaft. Excellent abrasion and wear resistance.
• Stainless Steel Cable Guard for maximum cable protection. Attached with stainless steel screws.
• Balanced Teflon® impregnated Impellers made of glass-filled thermoplastic, provide for lower friction for longer pump life.
• Stainless steel Hex Shaft with slotted end for test turning.
• Fully enclosed, glass-filled thermoplastic Diffusers and Stage Plates with stainless steel wear surfaces. Each stage is complete with an individual composite thrust washer for extra protection.
• Heavy wall, high quality Stainless Steel Pump Casing sized inside for perfect stage alignment.
• Glass-filled Noryl® Motor Support ½ HP thru 1 ½ Hp models. Available in Stainless Steel up to 5 HP.
• Stainless Steel screen, cannot snap off during installation.
VA
RIO
SPEE
D®
CO
NST
AN
T PR
ESSU
RE B
OO
STER
SYS
TEM
- SI
MPL
EX
60 Hz
55 Hz
50 Hz
45 Hz
40 Hz
60 Hz
55 Hz
50 Hz
45 Hz
40 Hz
60 Hz
55 Hz
50 Hz
45 Hz
40 Hz
60 Hz
55 Hz
50 Hz
45 Hz
40 Hz
Pump Model: 3-906B-3-T2Max Flow: 80 GPMMax Boost: 37 PSI
Pump Model: 3-908B-3-T3Max Flow: 140 GPMMax Boost: 44 PSI
Pump Model: 3-909B-3-T5Max Flow: 163 GPMMax Boost: 53 PSI
Pump Model: 3-910B-3-T7Max Flow: 175 GPMMax Boost: 69 PSI
LANCASTER PUMPVARIOspeed Constant Pressure Booster Systems - Simplex60 to 40 Hz Performance Curves -
3 HP2 HP
5 HP 7.5 HP
3-906B-3-T2-V21-N1-SX3-906B-3-T2-V21-N3R-SX
208/240 VAC Single Phase208/240 VAC Single Phase
HPThree PhaseThree Phase
NEMA 1NEMA 3R2
Booster System Model Power Supply Input to VFD * VFD Output to Motor VFD Enclosure
* The output voltage of the VFD cannot exceed the incoming voltage. Example: 208V in, 208V out (max).
3-908B-3-T3-V21-N1-SX3-908B-3-T3-V21-N3R-SX
208/240 VAC Single Phase208/240 VAC Single Phase
Three PhaseThree Phase
NEMA 1NEMA 3R3
3-909B-3-T5-V23-N1-SX3-909B-3-T5-V23-N3R-SX
208/240 VAC Three Phase208/240 VAC Three Phase
Three PhaseThree Phase
NEMA 1NEMA 3R5
7.53-910B-3-T7-V23-N1-SX3-910B-3-T7-V23-N3R-SX
208/240 VAC Three Phase208/240 VAC Three Phase
Three PhaseThree Phase
NEMA 1NEMA 3R
3-910B-3-T7-V43-N1-SX3-910B-3-T7-V43-N3R-SX
480 VAC Three Phase480 VAC Three Phase
Three PhaseThree Phase
NEMA 1NEMA 3R
based upon clean cold water , 1.0 SP GR
15 to 150 GPMRecommended System Operating Range
15 to 150 GPMRecommended System Operating Range
10 to 80 GPMRecommended System Operating Range
10 to 105 GPMRecommended System Operating Range
60 Hz
55 Hz
50 Hz
45 Hz
40 Hz
60 Hz
55 Hz
50 Hz
45 Hz
40 Hz
60 Hz
55 Hz
50 Hz
45 Hz
40 Hz
60 Hz
55 Hz
50 Hz
45 Hz
40 Hz
Pump Model: 3-906B-3-T2Max Flow: 80 GPMMax Boost: 37 PSI
Pump Model: 3-908B-3-T3Max Flow: 140 GPMMax Boost: 44 PSI
Pump Model: 3-909B-3-T5Max Flow: 163 GPMMax Boost: 53 PSI
Pump Model: 3-910B-3-T7Max Flow: 175 GPMMax Boost: 69 PSI
LANCASTER PUMPVARIOspeed Constant Pressure Booster Systems - Simplex60 to 40 Hz Performance Curves -
3 HP2 HP
5 HP 7.5 HP
3-906B-3-T2-V21-N1-SX3-906B-3-T2-V21-N3R-SX
208/240 VAC Single Phase208/240 VAC Single Phase
HPThree PhaseThree Phase
NEMA 1NEMA 3R2
Booster System Model Power Supply Input to VFD * VFD Output to Motor VFD Enclosure
* The output voltage of the VFD cannot exceed the incoming voltage. Example: 208V in, 208V out (max).
3-908B-3-T3-V21-N1-SX3-908B-3-T3-V21-N3R-SX
208/240 VAC Single Phase208/240 VAC Single Phase
Three PhaseThree Phase
NEMA 1NEMA 3R3
3-909B-3-T5-V23-N1-SX3-909B-3-T5-V23-N3R-SX
208/240 VAC Three Phase208/240 VAC Three Phase
Three PhaseThree Phase
NEMA 1NEMA 3R5
7.53-910B-3-T7-V23-N1-SX3-910B-3-T7-V23-N3R-SX
208/240 VAC Three Phase208/240 VAC Three Phase
Three PhaseThree Phase
NEMA 1NEMA 3R
3-910B-3-T7-V43-N1-SX3-910B-3-T7-V43-N3R-SX
480 VAC Three Phase480 VAC Three Phase
Three PhaseThree Phase
NEMA 1NEMA 3R
based upon clean cold water , 1.0 SP GR
15 to 150 GPMRecommended System Operating Range
15 to 150 GPMRecommended System Operating Range
10 to 80 GPMRecommended System Operating Range
10 to 105 GPMRecommended System Operating Range
X-Factor Series LXFILTERS AND NEUTRALIZERS
ACID NEUTRALIZERS, FILTERSLancaster’s acid neutralizers correct low pH water, which in turn protects your pipes, faucets, heaters, boilers and all appliances requiring the use of water. A water softener may also be recommended to remove hardness.
SEDIMENT/TURBIDITY (FILTER-AG)Lancaster’s sediment filters will remove dirt, silica, and most suspended matter from your water supply down to a 20 micron filtering level. Filter AG requires no chemical regenerents - just a simple, periodic backwash.
CARBON FILTERSLancaster’s carbon filters, through filtration and adsorption, remove organic chemicals and other contaminants which cause color, taste and odor problems.
IRON FILTERS; BIRM & MTMLancaster’s iron filters remove iron and manganese, also filter other suspended matter, prevent rust stains on clothing, appliances and remove taste and color of iron. When sulfur is present, MTM is the recommended mineral.
Model Number Tank Service GPM Backwash GPM
Color, Taste & Odor (Carbon) Filters Cont. Peak
7-LXCT-1B 10x44 5 8 6.5
7-LXCT-2B 13x48 7 9 10
7-LXCT-3B 14x65 10 12 10
Acid Neutralizer (Calcite) Filters
7-LXDAN-1B 10x47 (with dome plug) 5 8 6.5
7-LXDAN-1.5B 10x54 (with dome plug) 6 9 6.5
7-LXDAN-2B 13x48 (with dome plug) 7 10 10
7-LXDAN-3B 13x65 (with dome plug) 10 12 10
Sediment/Turbidity (Filter AG) Filters
7-LXST-1B 10x44 5 8 5.3
7-LXST-2B 13x48 7 9 9
7-LXST-3B 14x65 10 12 9
Iron (Birm) Filters
7-LXIM-1B 10x44 5 8 6.5
7-LXIM-2B 13x48 7 9 10
7-LXIM-3B 14x65 10 12 10
Iron (MTM) Filters
7-LXTPIM-1B 10x44 5 8 6.5
7-LXTPIM-2B 13x48 7 9 11
7-LXTPIM-3B 14x65 10 12 11
Note: When using Birm for iron removal, it is necessary that the water contain no oil or hydrogen sulfide, organic matter not to exceed 4-5ppm, the D.O. content equal at least 15% of iron content with a pH of 6.8 or more. If the influent water has a pH of less than 6.8, neutralizing additives such as calcite, corosex or soda ash may be used prior to the Birm filter to raise the pH. A water having a low D.O. level may be pretreated by aeration. Chlorination greatly reduces Birm’s activity. High concentrations of the chlorine compounds may deplete the catalytic coating.
WAT E R T R E AT M E N TLANCASTER •
www.LancasterWaterTreatment.com • 1-800-442-0786May 2016
DIAMOND LINE LX
– FILTERS & NEUTR
ALIZERS
www.LancasterPump.com • 1-800-442-0786
LANCASTERLANCASTER
SURV
IVO
R SERIES
SURVIVOR 4” SUBMERSIBLE PUMP MODEL NUMBER BREAKDOWN
Survivor 4” Submersible Pumps
2-2LST5007-2Catalog Section
Number of Stages
1 = 115 Volt, Single Phase 2 = 230 Volt, Single Phase 3 = 230 Volt, Three Phase (Additional Voltages Available)
2 = 2 Wire 3 = 3 Wire
P = Plastic Discharge Head Plastic Motor Support
L = Lancaster Hydro-Force Motor (no letter L) = Franklin Electric Motor
S = Stainless Steel Discharge Head Stainless Steel Motor Support
SP = Stainless Steel Discharge Head Plastic Motor Support
J = 5 GPM L = 7 GPM
T = 10 GPM U = 15 GPM
W = 22 GPM
50 = 0.50 HP 75 = 0.75 HP 100 = 1.0 HP 150 = 1.5 HP 200 = 2.0 HP 300 = 3.0 HP 500 = 5.0 HP
Lancaster Pump offers a broad selection of SURVIVOR 4” submersible well pumps. Horsepower from ½ to 5 HP, with the most popular size range ½ to 1½ HP, available in Corrosion-Resistant Thermoplastic or Super Strength Stainless Steel. Capacity ratings are 5, 7, 10, 15 and 22 gallons per minute with heads as high as 990 feet.
INSIDE A PUMP STAGE• Diffuser with stainless steel seal/wear surfaces for upper impeller hub
• Impeller eye surrounding lower hub
• Stage plate with stainless steel seal/wear surface for impeller eye
ASSEMBLED PUMP STAGE• Laminated phenolic thrust washer on top of every stage provides
down-thrust protection and axial sealing for the impeller inside the next stage above
BREAKDOWN• Glass-filled Noryl® Discharge Head with field replaceable fluted
Internal Check Valve. Molded jug handles - no need for safety cable adapter, ½ HP thru 1½ HP models. Available in Stainless Steel up to 5 HP.
• Fluted Polyurethane Bearing at top end of shaft. Excellent abrasion and wear resistance.
• Stainless Steel Cable Guard for maximum cable protection. Attached with stainless steel screws.
• Balanced Teflon® impregnated Impellers made of glass-filled thermoplastic, provide for lower friction for longer pump life.
• Stainless steel Hex Shaft with slotted end for test turning.
• Fully enclosed, glass-filled thermoplastic Diffusers and Stage Plates with stainless steel wear surfaces. Each stage is complete with an individual composite thrust washer for extra protection.
• Heavy wall, high quality Stainless Steel Pump Casing sized inside for perfect stage alignment.
• Glass-filled Noryl® Motor Support ½ HP thru 1 ½ Hp models. Available in Stainless Steel up to 5 HP.
• Stainless Steel screen, cannot snap off during installation.
LANCASTERLANCASTER
SURV
IVO
R SERIES
SURVIVOR 4” SUBMERSIBLE PUMP MODEL NUMBER BREAKDOWN
Survivor 4” Submersible Pumps
2-2LST5007-2Catalog Section
Number of Stages
1 = 115 Volt, Single Phase 2 = 230 Volt, Single Phase 3 = 230 Volt, Three Phase (Additional Voltages Available)
2 = 2 Wire 3 = 3 Wire
P = Plastic Discharge Head Plastic Motor Support
L = Lancaster Hydro-Force Motor (no letter L) = Franklin Electric Motor
S = Stainless Steel Discharge Head Stainless Steel Motor Support
SP = Stainless Steel Discharge Head Plastic Motor Support
J = 5 GPM L = 7 GPM
T = 10 GPM U = 15 GPM
W = 22 GPM
50 = 0.50 HP 75 = 0.75 HP 100 = 1.0 HP 150 = 1.5 HP 200 = 2.0 HP 300 = 3.0 HP 500 = 5.0 HP
Lancaster Pump offers a broad selection of SURVIVOR 4” submersible well pumps. Horsepower from ½ to 5 HP, with the most popular size range ½ to 1½ HP, available in Corrosion-Resistant Thermoplastic or Super Strength Stainless Steel. Capacity ratings are 5, 7, 10, 15 and 22 gallons per minute with heads as high as 990 feet.
INSIDE A PUMP STAGE• Diffuser with stainless steel seal/wear surfaces for upper impeller hub
• Impeller eye surrounding lower hub
• Stage plate with stainless steel seal/wear surface for impeller eye
ASSEMBLED PUMP STAGE• Laminated phenolic thrust washer on top of every stage provides
down-thrust protection and axial sealing for the impeller inside the next stage above
BREAKDOWN• Glass-filled Noryl® Discharge Head with field replaceable fluted
Internal Check Valve. Molded jug handles - no need for safety cable adapter, ½ HP thru 1½ HP models. Available in Stainless Steel up to 5 HP.
• Fluted Polyurethane Bearing at top end of shaft. Excellent abrasion and wear resistance.
• Stainless Steel Cable Guard for maximum cable protection. Attached with stainless steel screws.
• Balanced Teflon® impregnated Impellers made of glass-filled thermoplastic, provide for lower friction for longer pump life.
• Stainless steel Hex Shaft with slotted end for test turning.
• Fully enclosed, glass-filled thermoplastic Diffusers and Stage Plates with stainless steel wear surfaces. Each stage is complete with an individual composite thrust washer for extra protection.
• Heavy wall, high quality Stainless Steel Pump Casing sized inside for perfect stage alignment.
• Glass-filled Noryl® Motor Support ½ HP thru 1 ½ Hp models. Available in Stainless Steel up to 5 HP.
• Stainless Steel screen, cannot snap off during installation.
VA
RIOSPEED
® C
ON
STAN
T PRESSURE BOO
STER SYSTEM - SIM
PLEX
VARIOspeed® Constant Pressure Booster System - SimplexSYSTEM MODEL NUMBER NOMENCLATURE
3 - 906B - 3 - T2 - V21 - N1 - SXBOOSTER PUMP CONTROL PANEL
CATALOG SECTION SX = SIMPLEX
900B SERIES PUMP END NO.
3 = 3 PHASE MOTOR
T = TEFC MOTOR ENCLOSURE
2 = 2 HP3 = 3 HP5 = 5 HP7 = 7.5 HP V = VARIOspeed R
21 = 208/240VAC 1 PHASE INPUT23 = 208/240VAC 3 PHASE INPUT43 = 480VAC 3 PHASE INPUT
N1 = NEMA 1 (indoor)N3R = NEMA 3R (indoor/outdoor)
SYSTEM BREAKDOWN:1. VARIOspeed® N1 or 3R Control Panel2. Centrifugal Pump with Lead-Free Brass Impeller 3. 3PH TEFC motor4. Diaphragm Pressure Tank (Hydro-Pneumatic)5. Discharge Tee6. Variable Flow Demand Check Valve7. Flexible Coupling
8. Flexible SS Hose 9. Tank Cross (including)
• Pressure Gauge • Pressure Relief Valve• Pressure Transducer• Hose Bib
• Full Port Ball Valve
10. Enamel Coated Steel Base
9
1
6
7
3
2
10
4
5
8
X-Factor Series LXFILTERS AND NEUTRALIZERS
ACID NEUTRALIZERS, FILTERSLancaster’s acid neutralizers correct low pH water, which in turn protects your pipes, faucets, heaters, boilers and all appliances requiring the use of water. A water softener may also be recommended to remove hardness.
SEDIMENT/TURBIDITY (FILTER-AG)Lancaster’s sediment filters will remove dirt, silica, and most suspended matter from your water supply down to a 20 micron filtering level. Filter AG requires no chemical regenerents - just a simple, periodic backwash.
CARBON FILTERSLancaster’s carbon filters, through filtration and adsorption, remove organic chemicals and other contaminants which cause color, taste and odor problems.
IRON FILTERS; BIRM & MTMLancaster’s iron filters remove iron and manganese, also filter other suspended matter, prevent rust stains on clothing, appliances and remove taste and color of iron. When sulfur is present, MTM is the recommended mineral.
Model Number Tank Service GPM Backwash GPM
Color, Taste & Odor (Carbon) Filters Cont. Peak
7-LXCT-1B 10x44 5 8 6.5
7-LXCT-2B 13x48 7 9 10
7-LXCT-3B 14x65 10 12 10
Acid Neutralizer (Calcite) Filters
7-LXDAN-1B 10x47 (with dome plug) 5 8 6.5
7-LXDAN-1.5B 10x54 (with dome plug) 6 9 6.5
7-LXDAN-2B 13x48 (with dome plug) 7 10 10
7-LXDAN-3B 13x65 (with dome plug) 10 12 10
Sediment/Turbidity (Filter AG) Filters
7-LXST-1B 10x44 5 8 5.3
7-LXST-2B 13x48 7 9 9
7-LXST-3B 14x65 10 12 9
Iron (Birm) Filters
7-LXIM-1B 10x44 5 8 6.5
7-LXIM-2B 13x48 7 9 10
7-LXIM-3B 14x65 10 12 10
Iron (MTM) Filters
7-LXTPIM-1B 10x44 5 8 6.5
7-LXTPIM-2B 13x48 7 9 11
7-LXTPIM-3B 14x65 10 12 11
Note: When using Birm for iron removal, it is necessary that the water contain no oil or hydrogen sulfide, organic matter not to exceed 4-5ppm, the D.O. content equal at least 15% of iron content with a pH of 6.8 or more. If the influent water has a pH of less than 6.8, neutralizing additives such as calcite, corosex or soda ash may be used prior to the Birm filter to raise the pH. A water having a low D.O. level may be pretreated by aeration. Chlorination greatly reduces Birm’s activity. High concentrations of the chlorine compounds may deplete the catalytic coating.
WAT E R T R E AT M E N TLANCASTER •
www.LancasterWaterTreatment.com • 1-800-442-0786May 2016
DIAMOND LINE LX
– FILTERS & NEUTR
ALIZERS
www.LancasterPump.com • 1-800-442-0786
LANCASTERLANCASTER
4” ENCAPSULATED SUBMERSIBLE MOTORS
SINGLE PHASE TWO-WIRE (½ - 1½ HP, 230V) & THREE-WIRE (½ - 1 HP, 230V)
EQUIPPED WITH LIGHTNING ARRESTORS
TECHNICAL FEATURES
TWO-WIRE DESIGN• Split-phase induction run (IR) design with built-in electronic starter connected
in series to a high resistance auxiliary start winding – no capacitor required – electronic starter controls disengagement of start winding as a function of starting time and starting voltage.
THREE-WIRE DESIGN• Capacitor-start induction run (CSIR) design – control box required.
• Control box quick-disconnect design disconnects control box components from the electrical system when the lid is removed – will retrofit F.E. Q-D control boxes of same HP and voltage.
• Control box components include a 230V voltage relay for easy installation, two ground terminals, cable terminals up to AWG 8, and a start capacitor for higher starting torque.
• Control box painted steel enclosure with multiple knockouts is rated NEMA 3R for indoor or outdoor installation.
TWO-WIRE AND THREE-WIRE DESIGNS• Stator filled with special epoxy resin and hermetically sealed for a better insulation
of the winding and a greater heat exchange.
• Rotor and thrust bearings lubricated by water mixed with Propylene Glycol.
• Built-in check valve for restoring of cooling liquid (well water) as needed.
• Built-in lightning arrestors providing surge protection.
• Built-in automatic reset overload providing thermal (overheat) protection caused by high amperage and/or inadequate motor cooling.
• AISI 304 Stainless Steel motor frame shell, stator ends and liner, hermetically sealed for maximum corrosion resistance.
• AISI 303 Stainless Steel splined shaft end.
• Cationic epoxy electrocoated G20 cast iron top and bottom end brackets.
• AISI 304 Stainless Steel top and bottom end bracket covers.
• Shaft sealing system using labyrinth seal, sand slinger and lip seal.
• Pressure equalizing diaphragm.
• 4” NEMA flange.
• M8 threaded mounting studs.
• Removable plug-in lead cable.
• Degree of protection: IP68.
• Insulation: Class B.
• Time Rating: Continuous Duty.
• UL recognized component.
• UL classified water quality system component in accordance with ANSI/NSF 61 (health effects) and 372 (lead content).
FRANKLIN: Lancaster Pump is also teamed up with Franklin Electric’s 4” super stainless and high thrust submersible motors, delivering high quality and dependable service.
LANCASTER HYDRO-FORCE™
SURV
IVO
R SE
RIE
S
• Corrosion-resistant stainless steel exterior
• Stainless steel splined shaft
• Hermetically-sealed windings
• Filter check valve
• Water lubrication
• Kingsbury-type thrust bearing
• Pressure-equalizing diaphragm
• Built-in lightning arrestors (All single-phase, super stainless 200 & 230V three-phase)
• Removable water bloc lead
• UL Recognized and CSA certified component
• ANSI/ NSF 61 certified
• Industry standard NEMA mounting dimensions
VARIOspeed® Constant Pressure Booster System - SimplexDimensions & Weights
LANCASTERLANCASTER
SURV
IVO
R SERIES
SURVIVOR 4” SUBMERSIBLE PUMP MODEL NUMBER BREAKDOWN
Survivor 4” Submersible Pumps
2-2LST5007-2Catalog Section
Number of Stages
1 = 115 Volt, Single Phase 2 = 230 Volt, Single Phase 3 = 230 Volt, Three Phase (Additional Voltages Available)
2 = 2 Wire 3 = 3 Wire
P = Plastic Discharge Head Plastic Motor Support
L = Lancaster Hydro-Force Motor (no letter L) = Franklin Electric Motor
S = Stainless Steel Discharge Head Stainless Steel Motor Support
SP = Stainless Steel Discharge Head Plastic Motor Support
J = 5 GPM L = 7 GPM
T = 10 GPM U = 15 GPM
W = 22 GPM
50 = 0.50 HP 75 = 0.75 HP 100 = 1.0 HP 150 = 1.5 HP 200 = 2.0 HP 300 = 3.0 HP 500 = 5.0 HP
Lancaster Pump offers a broad selection of SURVIVOR 4” submersible well pumps. Horsepower from ½ to 5 HP, with the most popular size range ½ to 1½ HP, available in Corrosion-Resistant Thermoplastic or Super Strength Stainless Steel. Capacity ratings are 5, 7, 10, 15 and 22 gallons per minute with heads as high as 990 feet.
INSIDE A PUMP STAGE• Diffuser with stainless steel seal/wear surfaces for upper impeller hub
• Impeller eye surrounding lower hub
• Stage plate with stainless steel seal/wear surface for impeller eye
ASSEMBLED PUMP STAGE• Laminated phenolic thrust washer on top of every stage provides
down-thrust protection and axial sealing for the impeller inside the next stage above
BREAKDOWN• Glass-filled Noryl® Discharge Head with field replaceable fluted
Internal Check Valve. Molded jug handles - no need for safety cable adapter, ½ HP thru 1½ HP models. Available in Stainless Steel up to 5 HP.
• Fluted Polyurethane Bearing at top end of shaft. Excellent abrasion and wear resistance.
• Stainless Steel Cable Guard for maximum cable protection. Attached with stainless steel screws.
• Balanced Teflon® impregnated Impellers made of glass-filled thermoplastic, provide for lower friction for longer pump life.
• Stainless steel Hex Shaft with slotted end for test turning.
• Fully enclosed, glass-filled thermoplastic Diffusers and Stage Plates with stainless steel wear surfaces. Each stage is complete with an individual composite thrust washer for extra protection.
• Heavy wall, high quality Stainless Steel Pump Casing sized inside for perfect stage alignment.
• Glass-filled Noryl® Motor Support ½ HP thru 1 ½ Hp models. Available in Stainless Steel up to 5 HP.
• Stainless Steel screen, cannot snap off during installation.
VA
RIO
SPEE
D®
CO
NST
AN
T PR
ESSU
RE B
OO
STER
SYS
TEM
- SI
MPL
EXLANCASTER PUMPVARIOspeed Constant Pressure Booster Systems - Simplex
3-906B-3-T2-V21-N1-SX3-906B-3-T2-V21-N3R-SX
HP2
Booster System Model
R
3-908B-3-T3-V21-N1-SX3-908B-3-T3-V21-N3R-SX33-909B-3-T5-V23-N1-SX3-909B-3-T5-V23-N3R-SX5
7.53-910B-3-T7-V23-N1-SX3-910B-3-T7-V23-N3R-SX
3-910B-3-T7-V43-N1-SX3-910B-3-T7-V43-N3R-SX
Dimensions and Weights
VFD Enclosure: NEMA 3R
VFD Enclosure: NEMA 1
Dimensions are for estimating only
ALL DIMENSIONS ARE IN INCHES
ALL DIMENSIONS ARE IN INCHES
Inlet Outlet A B Weight
1.5 FPT
2 FPT
2 MPT
2 MPT
2.5 MPT
7.0 in.
7.0 in.
6.8 in.
25.9 in.
26.2 in.
27.7 in.
222 lbs.232 lbs.
225 lbs.235 lbs.
275 lbs.285 lbs.
295 lbs.299 lbs.
2 FPT
2.5 MPT 6.8 in. 27.7 in.2 FPT
295 lbs.311 lbs.2.5 MPT 6.8 in. 27.7 in.2 FPT
LANCASTER PUMPVARIOspeed Constant Pressure Booster Systems - Simplex
3-906B-3-T2-V21-N1-SX3-906B-3-T2-V21-N3R-SX
HP2
Booster System Model
R
3-908B-3-T3-V21-N1-SX3-908B-3-T3-V21-N3R-SX33-909B-3-T5-V23-N1-SX3-909B-3-T5-V23-N3R-SX5
7.53-910B-3-T7-V23-N1-SX3-910B-3-T7-V23-N3R-SX
3-910B-3-T7-V43-N1-SX3-910B-3-T7-V43-N3R-SX
Dimensions and Weights
VFD Enclosure: NEMA 3R
VFD Enclosure: NEMA 1
Dimensions are for estimating only
ALL DIMENSIONS ARE IN INCHES
ALL DIMENSIONS ARE IN INCHES
Inlet Outlet A B Weight
1.5 FPT
2 FPT
2 MPT
2 MPT
2.5 MPT
7.0 in.
7.0 in.
6.8 in.
25.9 in.
26.2 in.
27.7 in.
222 lbs.232 lbs.
225 lbs.235 lbs.
275 lbs.285 lbs.
295 lbs.299 lbs.
2 FPT
2.5 MPT 6.8 in. 27.7 in.2 FPT
295 lbs.311 lbs.2.5 MPT 6.8 in. 27.7 in.2 FPT
LANCASTER PUMPVARIOspeed Constant Pressure Booster Systems - Simplex
3-906B-3-T2-V21-N1-SX3-906B-3-T2-V21-N3R-SX
HP2
Booster System Model
R
3-908B-3-T3-V21-N1-SX3-908B-3-T3-V21-N3R-SX33-909B-3-T5-V23-N1-SX3-909B-3-T5-V23-N3R-SX5
7.53-910B-3-T7-V23-N1-SX3-910B-3-T7-V23-N3R-SX
3-910B-3-T7-V43-N1-SX3-910B-3-T7-V43-N3R-SX
Dimensions and Weights
VFD Enclosure: NEMA 3R
VFD Enclosure: NEMA 1
Dimensions are for estimating only
ALL DIMENSIONS ARE IN INCHES
ALL DIMENSIONS ARE IN INCHES
Inlet Outlet A B Weight
1.5 FPT
2 FPT
2 MPT
2 MPT
2.5 MPT
7.0 in.
7.0 in.
6.8 in.
25.9 in.
26.2 in.
27.7 in.
222 lbs.232 lbs.
225 lbs.235 lbs.
275 lbs.285 lbs.
295 lbs.299 lbs.
2 FPT
2.5 MPT 6.8 in. 27.7 in.2 FPT
295 lbs.311 lbs.2.5 MPT 6.8 in. 27.7 in.2 FPT