point to point microwave[1]
DESCRIPTION
Microwave Radio BasicsRadio Network Planning AspectsRadio Network Planning ProcessRadio wave PropagationLink Engineering & ReliabilityInterference AnalysisPtP MW Transmission IssuesUseful FormulaeTRANSCRIPT
![Page 1: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/1.jpg)
Point To Point Microwave Transmission
![Page 2: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/2.jpg)
Contents
Microwave Radio Basics Radio Network Planning Aspects Radio Network Planning Process Radio wave Propagation Link Engineering & Reliability Interference Analysis PtP MW Transmission Issues Useful Formulae
![Page 3: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/3.jpg)
What is Transmission ?• Transmission is an activity that carries information between Network Nodes
• Information is sent over a carrier between Network Nodes.
• Carrier is sent over a Transmission Media
• Commonly used Transmission Media : Copper Cables• Microwave Radio• Optical Fiber• Infra Red Radio
![Page 4: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/4.jpg)
Microwave Radio Basics
1. Basic Modules2. Configuration3. Applications4. Advantages
![Page 5: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/5.jpg)
Microwave Radio - Modules
Microwave Radio Terminal has 3 Basic Modules
Digital Modem : To interface with customer equipment and to convert customer traffic to a modulated signal
RF Unit : To Up and Down Convert signal in RF Range
Passive Parabolic Antenna : For Transmitting and Receiving RF Signal
Two Microwave Terminals Forms a Hop Microwave Communication requires LOS
![Page 6: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/6.jpg)
Basic Hardware Configurations
Non Protected or 1+0 Configuration
Protected or 1+1 Configuration, also known as MHSB
In MHSB Modem and RF Unit are duplicated
![Page 7: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/7.jpg)
Microwave Radio – Capacity Configurations
Commonly Used Capacity Configurations
4 x 2 Mbps or 4 x E1
8 x 2 Mbps or 8 x E1
16 x 2 Mbps or 16 x E1
155 Mbps or STM1
![Page 8: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/8.jpg)
Microwave Radio - Applications
As Transport Medium in Basic Service Networks
Mobile Cellular Network
Last Mile Access
Private Networks
![Page 9: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/9.jpg)
Microwave Radio Advantages
Advantages over Optical Fiber / Copper Cable System Rapid Deployment
Flexibility
Lower Startup and Operational Cost
No ROW Issues
Low MTTR
![Page 10: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/10.jpg)
Microwave Radio - Manufacturers
Few well known Radio Manufacturers Ericsson Nera NEC Siemens Fujitsu Nokia Alcatel Hariss
![Page 11: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/11.jpg)
Microwave Network Planning Aspects
1. Network Architecture2. Route Configuration3. Choice of Frequency Band
![Page 12: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/12.jpg)
Network Architecture
Common Network Architectures Spur or Chain
Star
Ring
Mesh
Combination of Above
![Page 13: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/13.jpg)
Spur ArchitectureB
C
D
E
A
•For N Stations N-1 Links are required•Nth station depends on N-1 Links
Spur Architecture
![Page 14: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/14.jpg)
Star Architecture
•For N Stations N-1 Links are required•Each Station depends on Only 1 Link
BC
DE
A
Star Architecture
![Page 15: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/15.jpg)
Loop Architecture
•For N Stations N Links are required•Route Diversity is available for all stations
B
C
DE
A
Loop Architecture
![Page 16: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/16.jpg)
Loop protection is effective against faults, which are caused by e.g.
•power failure
•equipment failure
•unexpected cut of cable
•human mistake
•rain and Multipath fading cutting microwave radio connections
![Page 17: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/17.jpg)
BTSMETROHUBMW RADIOSINGLE MODE MW LINKHSB MODE MW LINK
COPPER CONNECTION
Figure 2. Primary solution where loop masters (Metro Hub) are co-located in the BSC.
To Next BSC
To Next BSC
BSC
![Page 18: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/18.jpg)
Figure 3. Solution of using remote loop master Metro hub) co-located in a remote BTS
To Next BSC
To Next BSC
BSC
BTSMETROHUBMW RADIOSINGLE MODE MW LINKHSB MODE MW LINK
COPPER CONNECTION
![Page 19: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/19.jpg)
Mesh Architecture
•Each Station is Connected to Every Other•Full Proof Route Protection•For N sites (Nx2)-1
C
DE
A
Mesh Architecture
B
![Page 20: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/20.jpg)
Typical Network ArchitectureB
GDE
I
Typical Architecture
J
FA
C
•Typical Network Consist of Rings and Spurs
![Page 21: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/21.jpg)
Network Routes & Route Capacities
Inter- City routes - Backbone Backbone routes are planned at Lower Frequency
Bands 2, 6 and 7 GHz Frequency Bands are used Backbone routes are normally high capacity
routes Nominal Hop Distances 25 – 40 Km
Intra – City routes - Access Access routes are planned at Higher Frequency
Bands 15,18 and 23 GHz Frequency Bands are used Nominal Hop Distance 1 – 10 Km
![Page 22: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/22.jpg)
Frequency Bands
Frequency Band 7, 15, 18 and 23 GHz are allowed to Private Operators for deployment in Mw Transmission Network
15,18 and 23 GHz bands are used for Access Network
7 GHz band is used for Backbone Network Different Channeling Plans are available in
these bands to accommodate different bandwidth requirements
Bandwidth requirement is decided by Radio Capacity offered by the Manufacturer
![Page 23: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/23.jpg)
Microwave Propagation
![Page 24: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/24.jpg)
Free Space Propagation
• Microwave Propagation in Free Space is Governed by Laws of Optics
• Like any Optical Wave , Microwave also undergoes
- Refraction- Reflection
![Page 25: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/25.jpg)
Free Space Propagation - Refraction
• Ray bending due to layers of different densities
Bent Rays In Atmosphere
![Page 26: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/26.jpg)
Free Space Propagation - Refraction
• In effect the Earth appears elevated • Earth elevation is denoted by K Factor• K Factor depends on Rate of Change of
Refractivity with height• K= 2/3 Earth appears more elevated • K= 4/3 Earth appears flatter w.r.t K=2/3• K= Ray Follows Earth Curvature
![Page 27: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/27.jpg)
Free Space Propagation - Refraction
Effect of Refractivity Change
K = 2/3
Actual Ground
K = 4/3
![Page 28: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/28.jpg)
Microwaves are reflected over Smooth Surfaces Water Bodies
Reflected Signals are 180 out of phase Reflection can be a major cause of
outages Link needs to be planned carefully to
avoid reflections
Free Space Propagation – Reflections
![Page 29: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/29.jpg)
RF Propagation Reflections
Reflections can come from ANYWHERE - behind, under, in-front
6 cm difference can change Path geometry
![Page 30: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/30.jpg)
Fresnel Zone
The Fresnel zone is the area of space between the two antennas in which the radio signal travels.
For Clear Line of Sight Fresnel Zone Should be clear of obstacles
It is depends on Distance and Frequency
![Page 31: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/31.jpg)
FRESNEL ZONES
1st Fresnel Zone
Mid Path
![Page 32: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/32.jpg)
FRESNEL ZONE CLEARANCES
1ST Fresnel Zone = 17.3 (d1*d2)/f(d1+d2)
d1 = Distance in Kilometers from Antenna ‘A’ to mid pointd2 = Distance in Kilometers from Antenna ‘B’ to mid pointf = Frequency in GHz
Ad1 d2
B
![Page 33: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/33.jpg)
RF propagationFirst Fresnel Zone
Food M art
Direct Path = L
First Fresnel Zone
Reflected path = L + l/2
![Page 34: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/34.jpg)
RF propagationFree space versus non free space
Non-free space Line of sight required Objects protrude in the fresnel
zone, but do not block the path
Free Space Line of sight No objects in the fresnel zone Antenna height is significant Distance relative short (due to
effects of curvature of the earth)
![Page 35: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/35.jpg)
FRESNEL ZONE & EARTH BULGE
D2/8
Earth Bulge
Height = D2/8 + 43.3D/4F
43.3D/4F 60% first Fresnel Zone
D = Distance Between Antennas
H
![Page 36: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/36.jpg)
Earth Curvature
Obstacle Clearance
Fresnel Zone Clearance Antenna
HeightAntenna Height
Midpoint clearance = 0.6F + Earth curvature + 10' when K=1
First Fresnel Distance (meters) F1= 17.3 [(d1*d2)/(f*D)]1/2 where D=path length Km, f=frequency (GHz) , d1= distance from Antenna1(Km) , d2 = distance from Antenna 2 (Km)
Earth Curvature h = (d1*d2) /2 where h = change in vertical distance from Horizontal line (meters), d1&d2 distance from antennas 1&2 respectively
Clearance for Earth’s Curvature
•13 feet for 10 Km path
•200 feet for 40 Km path
Fresnel Zone Clearance = 0.6 first Fresnel distance (Clear Path for Signal at mid point)• 30 feet for 10 Km path
•57 feet for 40 Km path
RF PropagationAntenna Height requirements
![Page 37: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/37.jpg)
Microwave Network Planning Process
1. Design Basis2. Line of Sight Survey3. Link Engineering 4. Interference Analysis
![Page 38: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/38.jpg)
N
N
Y
Y
RF Nominal Planning (NP)/ Application for Frequency License
Define BSC Borders
Estimate BSC Locations
Preliminary Transmission Planning and LOS Checking
for possible BSCs
Finalize BSC Locations
Microwave Link Planning and LOS Checking for BTSs
Update LOS Reports, Frequency Plan, Planning
Database, Equipment Summary
Customer to apply SACFA based on Nokia Technical
Inputs
Change BTS Prime Candidate?
Change BTS Prime Candidate?
Figure 1. Microwave Link Planning Process
Planning Process
![Page 39: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/39.jpg)
Design Basis
Choice of Radio Equipment
Fresnel Zone Clearance Objectives
Availability / Reliability Objectives
Interference Degradation Objectives
Tower Height & Loading Restrictions
![Page 40: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/40.jpg)
Microwave Network Planning Process
Map Study for feasibility of Line of Sight and Estimating Tower Heights
Actual Field Survey for refining map data and finalizing Antenna Heights
Link Power Budgeting & Engineering Frequency and Polarization Assignments Interference Analysis (Network Level) Final Link Engineering (Network Level)
![Page 41: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/41.jpg)
Map Study SOI Maps are available in different Scales and Contour
Intervals 1:50000 Scale Maps with 20 M Contour Interval are
normally used for Map Study If your site co-ordinate in WGS 84 /72 then first convert it
to Indo Bangladesh datum then plot it on maps. Indian Topographic maps are printed according to this
datum so its mandatory to convert your lat / long before plotting to maps.
Contour values are noted at intersections. For definite contour interval is shown on the map and for
dash contour assume half interval which shown on the map.
![Page 42: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/42.jpg)
Map Study
Vegetation height (15-20m) is added to Map Data Path Profile is drawn on Graph for Earth Bulge
Factor (K) =4/3 and 2/3 Fresnel Zone Depths are Calculated & Plotted for
Design Frequency Band Antennae Heights are Estimated for Design
Clearance Criteria Intersection with Water Bodies is also noted AMSL of Sight is determined by Interpolation
![Page 43: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/43.jpg)
Field Survey
Equipment Required Data Required GPS Receiver Map Study Data Camera Magnetic Compass Altimeter Binocular / Telescope Flashing Mirror Flags Inclinometer Balloon Set Measuring Tapes
![Page 44: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/44.jpg)
Field Survey
Field Survey Map Data Validation Gathering Field inputs (Terrain Type, Average
Tree/Obstacle Height, Critical Obstruction etc.) Line of Sight Check, if feasible ,using flags, mirror Data related to other stations in the vicinity , their
coordinates, frequency of operation, antenna size, heights, power etc.
Proximity to Airport / Airstrip with their co-ordinates Field inputs are used to refine existing path profile
data , reflection point determination, reflection analysis
![Page 45: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/45.jpg)
RF propagationEnvironmental conditions
Line of Sight No objects in path
between antenna a. Neighboring
Buildings b. Trees or other
obstructions Interference
c. Power lines
![Page 46: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/46.jpg)
Fading
• Phenomenon of Attenuation of Signal Due to Atmospheric and Propagation Conditions is called Fading
• Fading can occur due to • Refractions• Reflections• Atmospheric Anomalies
![Page 47: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/47.jpg)
Fading
• Types of Fading• Multipath Fading• Frequency Selective Fading• Rain Fading
![Page 48: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/48.jpg)
Multipath Fading
• Multipath fading is caused due to reflected / refracted signals arriving at receiver• Reflected Signals arrive with
• Delay• Phase Shift
• Result in degradation of intended Signal
• Space Diversity Radio Configuration is used to Counter Multipath Fading
![Page 49: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/49.jpg)
Frequency Selective Fading
• Frequency Selective Fading • Due to Atmospheric anomalies different
frequencies undergo different attenuation levels• Frequency Diversity Radio Configuration is
used to Counter Frequency Selective Fading
![Page 50: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/50.jpg)
Rain Fading
• Frequency Band > 10 GHz are affected due to Rain as Droplet size is comparable to Wavelengths
• Rain Fading Occur over and above Multipath and Frequency Selective Fading
• Horizontal Polarization is more prone to Rain Fades
• Path Diversity / Route Diversity is the only counter measure for Rain Fade
![Page 51: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/51.jpg)
Drop Shape and Polarization
2.0mm
1mm 1.5mm
2.5mm
As raindrops increasein size, they get moreextended in the Horizontaldirection, and thereforewill attenuate horizontalpolarization more thanvertical polarization
![Page 52: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/52.jpg)
Fade Margin
• Margin required to account for Fading – Fade Margin
• Higher Fade Margin provide better Link Reliability
• Fade Margin of 35 – 40 dB is normally provided
![Page 53: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/53.jpg)
Link Engineering & Reliability
1. Link Budgeting2. Reliability Predictions3. Interference Analysis
![Page 54: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/54.jpg)
Hop Model
Outdoor Unit
Station B
Indoor Unit
Traffic
Outdoor Unit
Station A
Indoor Unit
Traffic
![Page 55: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/55.jpg)
Link Power BudgetReceived Signal Level = Rxl
RxlB = TxA – LA + GA – Fl + GB – LB Where
TXA = Trans Power Station A
LA = Losses at Station A (Misc.)
GA = Antenna Gain at Station A
Fl = Free Space Losses
GB = Antenna Gain at Station B
LB = Losses at Station B
RxlB = Rx. Level at Station B
RXL must be > Receiver Sensitivity always
![Page 56: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/56.jpg)
Link Power Budget – Receiver Sensitivity
Lowest Possible Signal which can be detected by Receiver is called Receiver Sensitivity or Threshold
•Threshold Value is Manufacturer Specific•Depends on Radio Design
•Higher (-ve) Value Indicates better Radio Design
![Page 57: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/57.jpg)
Link Engineering Software Tools are used
Inputs to the toolSight Co-ordinatesPath Profile DataTerrain Data & Rain DataEquipment DataAntenna DataFrequency and Polarization Data
Tool OutputAvailability Prediction
![Page 58: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/58.jpg)
RF propagation Simple Path Analysis Concept (alternative)
WP II
PC Card
pigtail cable
Lightning Protector
RF Cable Antenna
WP II
PC Card
pigtail cable
Lightning Protector
RF CableAntenna
+ Transmit Power
- LOSS Cable/connectors
+ Antenna Gain + Antenna Gain
- LOSS Cable/connectors
RSL (receive signal level) + Fade Margin = sensitivity
- Path Loss over link distance
Calculate signal in one direction if Antennas and active components are equal
![Page 59: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/59.jpg)
Link Engineering – Interference
Interference is caused due to undesirable RF Signal Coupling
Threshold is degraded due to interference
Degraded Threshold results in reduced reliability
![Page 60: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/60.jpg)
Link Engineering – Interference
Examples of Undesirable RF Couplings
Finite Value of XPD in Antenna is the Prime Cause
Solution : Use of High Performance Antenna
F1H
V
Cross Poler Coupling
![Page 61: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/61.jpg)
Link Engineering – Interference
Examples of Undesirable RF Coupling
Receiver Filter Cut-off is tappered Solution : Use Radio with better
Specifications
F2
Adjacent Channel
F1
![Page 62: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/62.jpg)
Link Engineering – Interference
Examples of Undesirable RF Coupling
Finite value of FTB Ratio of Antenna is Prime Cause
Solution : Antenna with High FTB Ratio
Front to Back
T : HiR : Low
T : HiR : Low
T : LowR : Hi
T : LowR : Hi
![Page 63: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/63.jpg)
Link Engineering – Interference
Examples of Undesirable RF Coupling
Solution : Choose Antenna Heights such a way there is no LOS for over reach
Over Reach
T : LowR : Hi
T : HiR : Low
T : HiR : Low
T : LowR : Hi
T : LowR : Hi
T : HiR : Low
![Page 64: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/64.jpg)
Link Engineering – Interference
Interference is calculated at Network Level Interference due to links
Within Network Outside Network (Links of other
Operators) Interfering Signal degrades Fade
Margin Engineering Calculation re-done with
degraded Fade Margin
![Page 65: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/65.jpg)
Link Engineering – Interference
Counter Measures Avoid Hi-Lo violation in loop Frequency Discrimination Polarization Discrimination Angular Discrimination High Performance Antennae Lower Transmit Power , always
advisable
![Page 66: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/66.jpg)
PtP Microwave Transmission - Issues
Link Performance is Seriously Affected due to Atmospheric Anomalies like Ducting Ground Reflections Selective Fading Excessive Rains Interferences Thunderstorms / High Winds causing Antenna
Misalignment Earthing Equipment Failure
![Page 67: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/67.jpg)
Some Useful Formulae
![Page 68: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/68.jpg)
Link Budget
+Tx A Rx B
A B
+GA +GB
-Lfs-A rain
BRainfsAAB GALGTxRx
![Page 69: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/69.jpg)
)log(2045.92 fdL fs
d=1km ---> L = 124 dBmd=2km ---> L = 130 dBm
d=1km ---> L = 121 dBmd=2km ---> L = 127 dBm
39 GHz 26 GHzExamples
Free Space Loss
d = distance in kilometers f = frequency in GHz
![Page 70: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/70.jpg)
RF PropagationBasic loss formula
Propagation Loss
d = distance between Tx and Rx antenna [meter]PT = transmit power [mW]
PR = receive power [mW]G = antennae gain
R TP P Gd
( )l4
2
Pr ~ 1/f2 * D2 which means 2X Frequency = 1/4 Power
2 X Distance = 1/4 Power
![Page 71: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/71.jpg)
Useful Formulae – Earth Bulge
Earth Bulge at a distance d1 Km
= d1 * d2 / (12.75 * K) Meter
Where d2 = (d – d1) Km (d Km Hop Distance)
K = K Factor
![Page 72: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/72.jpg)
Useful Formulae – Fresnel Zone
Nth Fresnel Zone Depth at a distance d1 Km
= N * 17.3 * ( (d1*d2) / (f * d) ) –1/2 Meter
Where d2 = (d – d1) Km d = Hop Distance in Km
f = Frequency in GHz N = No. of Fresnel zone (eg. 1st or 2nd )
![Page 73: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/73.jpg)
Tower Height Calculation :
Th = Ep + C + OH + Slope – Ea
C = B1 + F
Slope = (( Ea – Eb) d1)/ D
F = 17.3 ((d1xd2)/f X D) -1/2
B = (d1 x d2) / (12.75 x K )
Where, Th = Tower HeightEp = Peak / Critical ObstructionC = Other lossesB1 = Earth BuldgeF = Fresnel ZoneOH = Overhead ObstructionEa= Height of Site AEb= Height of Site Bd1= Dist. From site A to Obstructiond2= Dist. From site B to ObstructionD = Path Distancef= FrequencyK= 4/3
d1 d2
Ea Ep Eb
![Page 74: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/74.jpg)
Useful Formulae – Antenna Gain
Antenna Gain
= 17.6 + 20 * log10 (f *d) dBi See Note
Where d= Antennae Diameter in Meter f= Frequency in GHz
Note # Assuming 60% Efficiency
![Page 75: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/75.jpg)
Useful Formulae – Free Space Loss
Free Space Loss
Fl= 92.4 + 20 * log10 (f *d) dB
Where d = Hop Distance in Km
f = Frequency in GHz
![Page 76: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/76.jpg)
Useful Formulae – Geo Climatic Factor
Geo Climatic Factor
G = 10 –T * (Pl)1.5
Where T= Terrain Factor= 6.5 for Overland Path Not in Mountain= 7.1 for Overland Path in Mountain= 6.0 for Over Large Bodies of Water
Pl = Pl factor
![Page 77: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/77.jpg)
Useful Formulae – System Gain
System Gain = (Transmit Power + ABS(Threshold) ) dB
Fade Margin = FM = (Nominal Received Signal – Threshold) dB
Path Inclination = ABS ((h1 + A1) – (h2 + A2) ) / dWhere h1 = Ant. Ht. At Stn A
AGL Meterh2 = Ant. Ht. At Stn B
AGL Meter A1 = AMSL of Stn A Meter
A2 = AMSL of Stn B Meter
d = Hop Distance in KM
![Page 78: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/78.jpg)
Useful Formulae – Fade Occurrence Factor
Fade Occurrence Factor = = G * d 3.6 *f 0.89 * (1+ ) -1.4
Where G = Geo Climatic Factord = Hop Distance in Kmf = Frequency in GHz = Path Inclination in mRad
![Page 79: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/79.jpg)
Useful Formulae –Outage Probability
Worst Month Outage Probability (One Way) % = OWM
OWM % = * 10 –(FM/10)
Annual Unavailability (One Way) % = OWM * 0.3
Assuming 4 Worst Months in a Year
Annual Availability (Two Way) % = 100-(OWM*0.3*2)
![Page 80: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/80.jpg)
Sl No Second in year365 Days X 24 Hours X 60 Minute X 60 Seconds
31536000
1 Link Availability 99.995(Assumption)0.005(unavailablity)
2Total unavailable second in year
(100-99.995)% of Total second in year
1576.8
3Total unavailable minute in a year
Total second / 60 26.28
4Total unavailable second per day
Total second in year / 365 days
4.32
How To Calculate Total Unavailability of the MW link
![Page 81: Point to Point Microwave[1]](https://reader031.vdocuments.us/reader031/viewer/2022012315/5452c4e6af795919308b4e3c/html5/thumbnails/81.jpg)
1. Means if your design link annual
availability is 99.995%
2. Then 4.32 sec per day will outage in that particular link.