plumb4 edit
DESCRIPTION
mp11TRANSCRIPT
When water comes out as soon as the fire sprinkler is activated, the system is A. wetpipe B. pre-action C. deluge D. drypipe
2.
When there is a low pressure from the water main, what will you use to supply higher levels?
A.
booster pump
B. sump pump C.
pneumatic pump
D. jet pump
3.
What type of material used for the base of a septic tank
A.
Mass Concrete
B. Reinforced concrete C. Light weight concrete D.
Earth base
4.
What is the typical slope of a waste pipe
A.
1%
B. 2% C. 3% D. 4%
5.
Water enters through rim punchings and jets placed in an up-leg of the rear trap, filling the trapway and creating an instant siphon action without rise of water level. The result is quick water withdrawal. Large water surface provides an efficient and clean operation. With quiet flushing and moderate cost, this is the most popular residential model.
A. REVERSE-TRAP
B.
SIPHON-VORTEX
C. SIPHON-JET
D. WASH-DOWN
6.
Water enters through diagonal punching around the rim of the bowl, creating a vortex that draws the water down into the rear trap with a swirling action that scours the walls of the bowl. Water strikes two parallel ridges and folds over forming a jet, producing siphonic action. Large water surface provides a very efficient and clean process, and the flushing is extremely quiet. This model is mostly of one-piece construction with a low profile. Expensive.
A. SIPHON-VORTEX
B. SIPHON-JET
C.
REVERSE-TRAP
D. WASH-DOWN
7.
Water enters through an open rim, as though a bucket of water were dumped into the bowl, filling the front trapway and creating siphon action. This model provides quick removal of water with minimum water rise. Small water surface makes the model more vulnerable to soiling and clogging. This is the least efficient and most noisy type but lowest in cost.
A. WASH-DOWN
B. SIPHON-JET
C.
REVERSE-TRAP
D. SIPHON-VORTEX
8.
Used to connect the two ends of two pipes, neither of which can be turned
A.
COUPLING
B. CAULKING
C.
NIPPLE
D. TREAD
9.
This material is used to threaded pipe connections to prevent leakage
A teflon tape
.
B. solvent
C. fitting
D.
plumbing tape
10. The standard water pressure from nawasa, maynilad, manila water etc.
A.
20 psi
B.
40 psi
C.
60 psi
D.
80 psi
11. The principal artery of the venting system to which vent branches may be connected
A. MAIN VENT B.
LOOP or CIRCUIT VENT
C.
LOCAL VENT
D. GROUP VENT
12.
The length along the center of the pipe and fitting
A.
EMBEDMENT LENGTH
B. DEVELOPMENT LENGTH
C. DEVELOPED LENGTH D. SPAN
13. The extension of a soil or waste stack above the highest horizontal drain connected to the stack horizontal drain, the uppermost end above the roof
A. UNIT VENT B. STACK VENT C. RELIEF VENT D. DRY VENT
14.
Strong flushing action is created by a jet of water directed into the rim and jet. The force of the jet draws the bowl contents into the rear trap. It doesn't use siphonic action but relies on the driving force of jet action. At flush valve 25 psi is needed with 1.5-in. inlet spud. Large water surface and large trapway size make this model efficient and suitable for commercial use. Flushing is very noisy. Expensive.
A. REVERSE-TRAP B.
PRESSURE/TANKLESS
C. PRESSURE/TANK D. SIPHON-VORTEX
15. Refers to any group of two or more similar adjacent fixtures which discharge into a common horizontal waste or soil branch
A.
CIRCUIT OF FIXTURE
B. GROUP OF FIXTURE C.
BATTERY OF FIXTURE
16.
Water enters through rim punchings and through a jet that fills the rear trapway completely, creating a siphon action and resulting in quick withdrawal of water from the bowl. A water jet is located at the inlet of the trapway. Most of the bowl surface is covered with water. This model is efficient but moderately noisy. Its cost is reasonably low.
A. WASH-DOWN B.
REVERSE-TRAP
C. SIPHON-JET D. SIPHON-VORTEX
17.
Plumbing permit shall be invalid if works not commenced after a period of
A. 120 days B. 1 year C. 2 years D.
3 years
18.
It is added to water to reduce salinity
A.
disinfectant
B. solvent C. electrolysis D.
salt prurifier
19. Is the lowest portion of the inside of any pipe or conduit that is not vertical A. INVERT B.
UNDER
C.
BASED
20. Is the flow of water or other liquids, mixtures or substances into the distributing pipes of a supply of water from any source other than its intended source A. BACK SIPHONAGE B.
BACKFLOW
C.
BACK PRESSURE
D. BEHIND FLOW
21.
Is the extended portion of a pipe that is closed at one end to which no connections are made on the extended portion
A.
LAST LINE
B.
DEAD END
C. FINAL PIPE
22. Is the backflow of used, contaminated or polluted water from a plumbing fixture due to negative pressure A. BACK SIPHONAGE B. BEHIND FLOW C.
BACK PRESSURE
23. Is a pipe on the fixture side of the trap through which vapor or foul air is removed from a room fixture A. BRANCH VENT B.
LOCAL VENT
C.
LOOP or CIRCUIT VENT
D. GROUP VENT
24. Is a pipe connecting several fixtures A.
FIXTURE BRANCH
B.
FIXTURE PIPE
C.
FIXTURE LINE
25.
Is a device located at the bottom of the tank for the purpose of flushing water closets and and similar fixture
A.
FLOOD LINE
B.
FLOOD LEVEL
C. FLOOD MEASURED
26.
Is plugging an opening with oakum, lead or other materials
A.
COUPLING
B. CAULKING C.
NIPPLE
D. TREAD
27.
Installation of all parts of the plumbing system which can be completed prior to the installation of fixtures
A. ROUGH IN B. ROUGH OUT C. ERECTION D.
INSTALLATION
28.
Includes all piping within public or private which conveys sewage, rain water or often liquid waste to a legal point of disposal but does not include the main of a public sewer system or private or or public sewerage treatment
A. DRAINAGE SYSTEM B.
SEWER SYTEM
C. STORM DRAIN SYSTEM
29.
How can you differentiate between soil pipe and waste pipe when laid side by side
A. color B.
material
C. smell D. diameter
30. An arrangement of venting so installed that that one vent pipe will serve two traps A.
GROUP VENT
B.
DRY VENT
C. RELIEF VENT D.
UNIT VENT
31.
A vent which also serves as a drain
A.
DRY VENT
B. WET VENT C. RELIEF VENT D.
STACK VENT
32. A vent that does not serve as drain and is located where if is not exposed to back up of waste from a drainage pipe
A.
DRY VENT
B.
BRANCH VENT
C. CIRCUIT VENT D. CONTINOUS VENT
33.
A vent installed so as to permit additional circulation of air between the drainage and vent systems where the drainage systems might otherwise be air bound
A.
RELIEF VENT
B.
UNIT VENT
C.
DRY VENT
D. GROUP VENT
34. A vent connecting one or more individual vents with a vent stack or stack vent A. BRANCH VENT B. CIRCUIT VENT C.
COMMON VENT
D. CONTINOUS VENT
35.
A vent connecting at the junction of two fixture drains and serving as a vent for both fixtures A single vent that ventiliates multiple traps, in the case of back to back fixture
A.
COMMON VENT
B.
BRANCH VENT
C. CIRCUIT VENT D. CONTINOUS VENT
36. A valve permitting a liquid or gas to flow in one direction A.
check valve
B.
gate valve
C.
float valve
D.
globe valve
37.
A steel tank is located inside the china tank. Uses pressure from the water supply system. A 1.5 in. water supply line provides 25 psi pressure, compressing trapped air in the tank. When flushed the compressed air forces the water out. The bowl is designed to accept the torrent of water. The crest of the surging water empties the bowl through the enlarged trap. Large water surface makes this model efficient. Design features make it suitable for residential use. Flushing is very noisy. Low water usage (1.5 gpf) helps conserve water. Expensive.
A.
PRESSURE/TANK
B.
SIPHON-VORTEX
C.
PRESSURE/TANKLESS
D. REVERSE-TRAP
38.
A short internally threaded section of pipe, used to join two pipes of conduits
A.
COUPLING
B. CAULKING C NIPPLE
. D. TREAD
39. A pipe installed to vent, a fixture trap and w/c connects with the vent system above the fixture served or terminates in the open air A. LOOP or CIRCUIT VENT B.
BRANCH VENT
C.
INDIVIDUAL VENT
D. GROUP VENT
40. A pipe connecting upward from a soil or waste stack to a vent stack for the purpose of preventing pressure changes in the stack A. YOKE VENT B. STACK VENT C. RELIEF VENT D. WET VENT
41.
A flange that is not drilled
A.
BLANK FLANGE
B.
FLANGE
C.
FRONT FLANGE
D. BACK FLANGE
42. A flange that closes the end of a pipe line used to discharge water A.
BACK FLANGE
B. BLIND FLANGE C.
BACK FLANGE
D. FLANGE
43. A branch vents that performs its functions for two or more traps A. CONTINOUS VENT B.
GROUP VENT
C.
BRANCH VENT
D. DRY VENT
44.
A branch vent that serves two or more traps and extends from in front of the last fixture connection of a horizontal branch to the vent stack
A.
COMMON VENT
B.
BRANCH VENT
C. CIRCUIT VENT D. CONTINOUS VENT
45.
A vertical vent that is the continuation of the drain to which the vents connect
A. CONTINOUS VENT B. CIRCUIT VENT C.
BRANCH VENT
D. DRY VENT
46.
A metallic sleeve, join to an opening of pipe, into which a plug is screwed that can be removed for the purpose of cleaning
A.
SELEEVE
B.
PLUD SLEEVE
C.
FERRULE
47.
A circuit vent which loop backs to connect with a stack vent instead of a vent stack Any vent connecting a horizontal branch or fixture drain with the stack vent of the originating waste or soil stack
A. INDIVIDUAL VENT
B.
GROUP VENT
C LOOP or CIRCUIT VENT
. D. BRANCH VENT
48. How many gallons of water for the Water Closet Flushing requirements? A. 30 gallons B.
b. 0.75 – 2 gallons
C.
c. 3 – 5 gallons
D. d. 2 – 2.5 gallons
49.
A bathroom containing a water closet and a lavatory
A.
Toilet and Bath
B. b. Powder Room C. c. Full Bath D. d. Half Bath
50.
. Water which undergoes treatment, either physical, biological or chemical means to improve water quality.
A.
a. Contaminated Water
B.
b. Purified Water
C.
c. Natural Water
D. d. Pure Water
51.
The lowest portion of the inside top surface of the channel through trap.
A.
a. Crown
B.
b. Spring Line
C. c. Dip D. d. Invert
1.
What is the minimum size vent for a water closet?
A.
1 1/2"
B.
3"
C.
2"
D. 4"
2.
What is the distance from the top of water heater to relief valve?
A.
6"
B.
8"
C.
5"
D. 5 3/4" E. none of these
3.
How many dfu's are allowed on a 2" horizontal drain line?
A.
4
B.
12
C.
3
D.
5
E. 6
4.
What is the maximum distance away from a water heater you can install a shut off valve?
A.
12"
B.
5'
C.
3'
D.
24"
E. 7'
5.
In a closed water system is it applicable to install a expansion tank?
A. yes B. no C. sometimes D.
depends on what faucet you use
6.
How many water closets are allowed on a 3" horizontal waste line?
A.
6
B.
2
C.
4
D.
10
E. 1
7.
What temp is considered hot water?
A. 105 B 115
. C. 120 D.
85
8.
At what temp does a shower valve have to be set at?
A. 120 B. dosent matter C. 105 D. 115 E.
85
9.
At what range is tempered water considered?
A. 85-120 B.
85-115
C. 85-105 D. 85-135
10. Below what temp is cold water? A. 105 B.
115
C. 120 D. 110 E.
85
11. What size trap is used for a bradley sink? A.
4"
B.
2"
C.
1 1/2"
D. 3"
12. What is the minimum distance between a tub spout and the flood rim level of a bath tub? A.
6"
B.
7"
C.
6 1/4"
D. 5 3/4" E. none of these
13.
When you install an ejector pump, in what order is it installed?
A.
pump, ball valve, check valve
B.
ball valve, pump, check valve
C.
check valve, pump, ball valve
D. pump, check valve, ball valve
14.
Is it code to pipe a ejector pump waste line into a 4" horizontal?
A. true B. false
.
The device being used to eliminate the noise cause by water hammer
A. SHOCK RELIEF AND EXPANSION CHAMBER
B. PRESSURE REDUCING VALVE C.
OVERHEAD STORM DRAIN
D. ABSORPTION TRENCH
2.
Wet standpipe for riser more than 15m
A.
64mm or 2 1/2"
B. 51mm or 2 " C.
26mm or 1"
D.
101mm or 4"
3.
Trap size of fixtures for Sinks (Kitchen or residence)
A.
1 1/2"
B.
1"
C.
2"
D. 1/4"
4.
Color coding of high pressure steam
A. BLACK B. BLUE C. WHITE D.
GREEN
5.
An underground tank reservoir to store water
A.
CORPORATION STOP
B. CISTERN C.
ABSORPTION TRENCH
D. CATCH BASIN
6.
The water column that seals the escape of unhealthy gases in the sanitary drainage system
A.
TRAP OR WATER SEAL
B. CISTERN C.
AIR TRAP
D. CATCH TRAP
7.
A vent that does not serve as drain and is located where if is not exposed to back up of waste from a drainage pipe
A. CIRCUIT VENT B. DUAL VENT C. INDIVIDUAL
VENT D.
DRY VENT
8.
Is the extended portion of a pipe that is closed at one end to which no connections are made on the extended portion
A.
DEAD END
B. DRAINAGE SYSTEM C.
FIXTURE BRANCH
D. PLUMBING SYSTEM
9.
Minimum number of water closet required for female office and public buildings
A.
1 CLOSETS
B. 2 CLOSETS
C. 3 CLOSETS
D. 4 CLOSETS
10. Refers to any group of two or more similar adjacent fixtures which discharge into a common horizontal waste or soil branch A. BLANK FLANGE B. UNION C.
DEAD END
D.
BATTERY OF FIXTURE
11.
A vent which also serves as a drain
A.
DRY VENT
B. DUAL VENT C. WET VENT D. RELIEF VENT
12. Slope of house sewer connected from the building to the main sewer A. 5 PERCENT B.
2 PERCENT
C. 3 PERCENT D.
6 PERCENT
13. Is a pipe connecting several fixtures A. WATER RESERVOIR B. CORPORATION
STOP C.
FIXTURE BRANCH
D.
OVERHEAD STORM DRAIN
14. Moderately noisy. Similar to siphon jet except that trap passageway and water surface area are smaller A. BIDET B.
BLOW OUT
C. WASH DOWN D. REVERSE TRAP
15. Trap size of fixtures for slop sinks (with combine trap) A.
3"
B.
2"
C.
1 1/2"
D. 2 1/2"
16.
Trap size of fixtures for slop sinks (ordinary)
A.
2"
B.
3"
C.
4"
D. 1"
17.
1/2", 3/4", 1", 1 1/4", 1 1/2", 2, 2 1/2", 3", 4", 6", 8", 10", 12"
A. PVC PIPE SIZES B. GI PIPE SIZES C.
WASTE PIPE SIZES
D. TRAP SIZES OF FIXTURES
18. Trap size of fixtures for Sinks (dishwashers) A.
1 1/2"
B.
1"
C.
1 1/4"
D. 1/2"
19.
Is plugging an opening with oakum, lead or other materials
A. CAULKING B.
DEAD END
C.
FIXTURE BRANCH
D.
FERRULE
20.
A pipe fitting within the interconnection of pipes for the purpose of easy dismantling of the connection when needed
A.
UNION PATENT
B. ABSORPTION TRENCH C.
WATER RESERVOIR
D. CAULKING
21.
A trench containing course aggregate and a distribution tile pipe through which septic tank effluent may flow covered with earth
A. ABSORPTION TRENCH B. CATCH BASIN C.
ILLUMINATION
D. AIR TRAP
22. A wye connections used on fire lines so that two lines of hose maybe connected to the hydrant or to the same nozzle A. TRAP SEAL B.
SIAMESE CONNECTIONS
C. COUPLING D.
BATTERY OF FIXTURE
23. Minimum head of water required in section of plumbing for water test A. 5 HEADS B.
4 HEADS
C.
3 HEADS
D. 2 HEADS
24. A type of fitting for yoke bent A. COUPLING B.
SIAMESE CONNECTIONS
C. CULVERT D.
WYE FITTING
25.
The luminous flux density incident on a surface
A. FLOOD LEVEL B. ILLUMINATION C. PLUMBING SYSTEM D.
FIXTURE BRANCH
26.
Trap size of fixtures for Floor drain
A.
2"
B. 2 1/2" C.
3"
D. 4"
27.
Trap size of fixtures for Combination fixture
A.
1"
B. 1 1/2" C.
1/2"
D. 1/4"
28.
A valve which maintains uniform pressure on its outlet side regardless of its pressure fluctuations on the inlet side above the pressure level
A. COMPRESSION VALVE B. TRAP OR WATER SEAL C. PRESSURE REDUCING VALVE D. FLUSHOMETER
29. Trap size of fixtures for Bidet
A.
1 1/2"
B.
1"
C.
1/4"
D. 1/2"
30.
Maximum height of Fire Service Connection from the grade/floor
A. 122mm
B. 125mm C. 130m
m D.
118mm
31.
A valve which in the water flow is shut off by a flat disk that is screwed down onto its seat
A. COMPRESSION VALVE B. OVERHEAD STORM DRAIN C. PRESSURE REDUCING VALVE D. UNION PATENT
32.
A short internally threaded section of pipe, used to join two pipes of conduits
A. INVERT B. DEVELOPED LENGTH C. FLOOD
LEVEL D. COUPLING
33.
Installation of all parts of the plumbing system which can be completed prior to the installation of fixtures
A.
DEAD END
B.
BLIND FLANGE
C. ROUGH IN D. SOIL PIPE
34. Is the maximum vertical depth of liquid that a trap will retain measure between the crown weir and the top of the dip of the trap A. TRAP SEAL B.
NIPPLE
C. FERRULE D. TRAP OR WATER SEAL
35. Is the lowest portion of the inside of any pipe or conduit that is not vertical A. ROUGH IN B. INVERT C.
FIXTURE BRANCH
D. SOIL PIPE
36. A U-shaped pipe filled with water and located beneath the plumbing fixtures to form a seal against the passages of gases and odors A.
AIR TRAP
B.
BIDET
C. WASH DOWN D. SIPHON-JET
37.
Trap size of fixtures for Laundray trays
A.
1 1/2"
B.
1"
C.
2"
D. 1 1/4"
38. Trap size of fixtures for Urinals (through) A.
2 1/4"
B.
1"
C.
1 1/2"
D. 2"
39.
Another classification of storm drain, besides from inside drain and outside drain
A.
OVERHEAD STORM DRAIN
B. UNION PATENT C. FLUSHOMETER D. CATCH BASIN
40.
The location of water well to nearest septic vault
A.
80 FEET OR MORE
B. 50 FEET OR MORE
C.
20 FEET OR MORE
D. 45 FEET OR MORE
41.
A basin like fixture design to be struddled for bathing the genitals and posterior parts of the body
A.
URINALS
B.
BIDET
C. SIPHON-VORTEX D.
WYE FITTING
42. A pipe installed to vent, a fixture trap and w/c connects with the vent system above the fixture served or terminates in the open air A. INDIVIDUAL
VENT B. LOOP or CIRCUIT VENT C.
RELIEF VENT
D. STACK VENT
43.
Fitting for base or soil stack and building drain
A.
1/2" BEND
B. 1/4" BEND C. 1 1/4" BEND D. 1 1/2" BEND
44.
Includes all piping within public or private which conveys sewage, rain water or often liquid waste to a legal point of disposal but does not include the main of a public sewer system or private or or public sewerage treatment
A. DRAINAGE SYSTEM B.
TRAP SEAL
C.
SIAMESE CONNECTIONS
D. PLUMBING SYSTEM
45.
Is a device located at the bottom of the tank for the purpose of flushing water closets and and similar fixture
A. FLOOD LEVEL B. INVERT C. ROUGH IN D. SOIL PIPE
46. The third kind of water after the storm water and area water
A.
YELLOW WATER
B.
GREEN WATER
C. BLUE WATER D. BLACK WATER
47. The principal artery of the venting system to which vent branches may be connected A.
MAIN VENT
B.
RELIEF VENT
C.
UNIT VENT
D.
YOKE VENT
48.
Tap used in high pressure water system with an interval valve to control the flow of water
A. COMPRESSION VALVE B.
PRESSURE COCK
C. PRESSURE REDUCING VALVE D. UNION PATENT
49.
Trap size of fixtures for Wash basin (lavatories)
A.
2"
B. 1 1/4" C.
1"
D. 2 1/4"
50.
Minimum cost. Least efficient subject to clogging, noisy. Simple washout and emptying through small irregular passageway, prohibited by some health codes
A. WASH DOWN B.
REVERSE TRAP
C. BLOW OUT D.
BIDET
51. A vent connecting one or more individual vents with a vent stack or stack vent A.
BRANCH VENT
B. COMMON VENT C.
CIRCUIT VENT
D.
CONTINOUS VENT
52. The type of bathtub oher than sunken, square, free standing A. RECESSED B. INSID
E C. CORNER D. EMBED
53. Is any pipe which conveys the discharge of water closets of fixture having similar function w/ or w/o the discharge of other fixtures to the building drain A. WATER RESERVOIR B.
TRAP SEAL
C. SOIL PIPE
D. RECESSED
54. An arrangement of venting so installed that that one vent pipe will serve two traps A.
YOKE VENT
B.
STACK VENT
C. LOCAL VENT D. UNIT VENT
55.
Trap size of fixtures for Sink (hotel or public)
A.
2"
B. 2 1/2" C.
1"
D. 2 1/4"
56.
Trap size of fixtures for Bath sitz
A.
1 1/2"
B.
1"
C.
1/4"
D. 1/2"
57.
Minimum discharge pipe and fitting for bath tub1 1/2"
A.
2 1/2"
B. 1 1/2" C.
2
D. 1 1/4"
58. A device that discharge a predetermined volume of water to fixture for flushing purposes and is activated by direct water pressure A.
ILLUMINATION
B.
FLUSHOMETER
C. SIPHON-JET D. URINALS
59. Ratio of water closets for female population for principal worship places A.
RATIO OF 1:75
B.
RATIO OF 1:85
C. RATIO OF 1:70 D.
RATIO OF 1:60
60. Minimum height of Fire Service Connection from the grade/floor A.
35 mm.
B. 45 mm. C.
46 mm.
D. 36 mm.
61. A flange that closes the end of a pipe line used to discharge water A. DRAINAGE SYSTEM B.
NIPPLE
C.
BACKFLOW
D. BLIND FLANGE
62. A passage under a road, embankment or canal which allow for the flow of water A.
CULVERT
B. CISTERN C.
AIR TRAP
D. CATCH BASIN
63. Ratio of water closets for female population for elementary and secondary school
A.
RATIO OF 1:75
B.
RATIO OF 1:25
C. RATIO OF 1:45 D.
RATIO OF 1:55
64. See common vent A.
DRY VENT
B. DUAL VENT C.
LOOP or CIRCUIT VENT
D. LOCAL VENT
65.
An underground structure for drainage into which water from the roof or floor will drain through sewer
A. ABSORPTION TRENCH B. CATCH BASIN C. CISTERN D. CORPORATION
STOP
66.
A vent connecting at the junction of two fixture drains and serving as a vent for both fixtures a single vent that ventiliates multiple traps, in the case of back to back fixture
A.
BRANCH VENT
B. COMMON VENT C.
CONTINOUS VENT
D.
DRY VENT
67. Used to connect the two ends of two pipes, neither of which can be turned A.
UNION
B.
ROUGH IN
C. SOIL PIPE
D.
FERRULE
68. Considered extension of bulding drain outside the building wall A. 6
FEET B. 5
FEET C.
7 FEET
D.
4 FEET
69. Install to be able to meet the water requirements during peak demands from a low yielding water well A. SHOCK RELIEF AND EXPANSION
CHAMBER B. BLACK WATER C.
COMPRESSION VALVE
D. WATER RESERVOIR
70.
Trap size of fixtures for Water closets
A.
4"
B.
3"
C.
6"
D. 2"
71. Trap size of fixtures for Bathfoot A 1 1/2"
. B. 2 1/2" C.
1"
D. 1 1/4"
72. Trap size of fixtures for pantry or bar A.
1 1/2"
B. 1 1/4" C.
1"
D.
2
73.
Ratio of urinals for elementary schools
A.
RATIO OF 1:85
B.
RATIO OF 1:75
C. RATIO OF 1:65 D.
RATIO OF 1:70
74.
Dry standpipe for a riser below 23m
A.
6"
B.
3"
C.
4"
D. 2"
75.
A short length of pipe with threads at each end; used to join couplings or fittings
A.
DEAD END
B.
NIPPLE
C.
FIXTURE BRANCH
D. PLUMBING SYSTEM
76.
Ratio of lavatory to number of occupants
A. RATIO OF 1:5 B.
RATIO OF 1:3
C. RATIO OF 1:4 D. RATIO OF 1:2
77.
Color coding for fuel oil division
A. BLACK B. BLUE C. GREEN D. WHITE
78.
Trap size of fixtures for Urinals (pedestal)
A.
2"
B. 2 1/2" C.
3"
D. 2 1/4"
79. Trap size of fixtures for Bath tub A 1"
. B.
2"
C.
1 1/2"
D. 1 1/4"
80. The extension of a soil or waste stack above the highest horizontal drain connected to the stack horizontal drain, the uppermost end above the roof A.
STACK VENT
B. YOKE VENT C. INDIVIDUAL
VENT D. LOOP or CIRCUIT VENT
81.
A vent installed so as to permit additional circulation of air between the drainage and vent systems where the drainage systems might otherwise be air bound
A.
RELIEF VENT
B.
STACK VENT
C. GROUP VENT D. STACK VENT
82. Another name for corporation cock A. REVERSE TRAP B.
SIPHON-VORTEX
C. BLOW OUT D. CORPORATION
STOP
83.
Sanitary, efficient very quiet. A toilet bowl into which the flushing water enters through the rim and siphonic action initiated by a water jet draws the contents of the bowl through the trapway
A. SIPHON-JET B.
SIPHON-VORTEX
C.
SIPHON-SAT
D.
SIPHON-JETSKI
84.
Dry standpipe for a riser more than 23m
A.
6"
B.
3"
C.
4"
D. 2"
85.
Quiet, extermely sanitary. Like the siphon jet but having the flushing water directed through the rim to create a vortex that scours the bowl
A. SIPHON-JET B.
SIPHON-VORTEX
C.
SIPHON-SAT
D.
SIPHON-JETSKI
86. No building supply pipe shall be less than WHAT size in diameter A. 19.05mm or 3/4" B. 19.00mm or 3/8" C. 18.00mm or 3/16" D.
19.50mm or 3/4"
87. Trap size of fixtures for Fountain cupsiders A. 1/2" B. 1 1/2"
C.
1 1/4"
D. 1"
88. Is the backflow of used, contaminated or polluted water from a plumbing fixture due to negative pressure A. BACK SIPHONAGE B.
BACKFLOW
C. BLIND FLANGE D.
YOKE VENT
89. Is a pipe on the fixture side of the trap through which vapor or foul air is removed from a room fixture A.
MAIN VENT
B.
LOCAL VENT
C.
STACK VENT
D.
WET VENT
90. Trap size of fixtures for Urinals (up) A.
1 1/2"
B.
1"
C.
1 1/4"
D. 1/2"
91.
Trap size of fixtures for Urinal (stall)
A.
2 1/2"
B.
3"
C.
1 1/2"
D. 2"
92. Trap size of fixtures for Drinking fountain A. 1/2" B. 1/4" C.
1 1/4"
D. 1"
93.
Wet standpipe for a riser not more than 15m
A. 51mm or 2" B. 76mm or 3" C. 101mm or 4" D.
26mm r 1"
94.
A metallic sleeve, join to an opening of pipe, into which a plug is screwed that can be removed for the purpose of cleaning
A.
CISTERN
B.
FERRULE
C. TRAP SEAL D.
INVERT
95.
Includes water supply and distribution pipe; plumbing fixture and traps, soil waste and vent pipes; house drain and house sewers including their respective connections
A. PLUMBING SYSTEM
B.
SIAMESE CONNECTIONS
C. TRAP SEAL D. WATER RESERVOIR
96. Is the flow of water or other liquids, mixtures or substances into the distributing pipes of a supply of water from any source other than its intended source A. BACKFLOW B. BACK SIPHONAGE C.
BATTERY OF FIXTURE
D. BLANK FLANGE
97.
Noisy but highly efficient. Strong jet into leg forces contents out
A.
BLOW OUT
B.
BIDET
C. REVERSE TRAP D. SIPHON-JET
98. Trap size of fixtures for Bath shower stall A.
2 1/2"
B.
3"
C.
2"
D. 2 1/4"
99.
A flange that is not drilled
A. BLANK FLANGE B. COUPLING C. CAULKING D. DRAINAGE SYSTEM
100. Service drop conductor clearance over the roof A.
2.50 M.
B. 3.00 M. C.
3.50 M.
D. 2.00 M.
101.
A branch vent that serves two or more traps and extends from in front of the last fixture connection of a horizontal branch to the vent stack
A.
BRANCH VENT
B. COMMON VENT C.
CIRCUIT VENT
D.
CONTINOUS VENT
102. Minimum height of Dry Standpipe Outlet from the floor line A.
53 mm.
B. 50 mm. C.
60 mm.
D. 61 mm.
103. A branch vents that performs its functions for two or more traps A.
CONTINOUS VENT
B.
MAIN VENT
C.
UNIT VENT
D.
GROUP VENT
104. A pipe connecting upward from a soil or waste stack to a vent stack for the purpose of preventing pressure changes in the stack A.
DRY VENT
B. YOKE VENT
C. LOCAL VENT D.
WET VENT
105. The length along the center of the pipe and fitting A.
SOIL PIPE
B. DEVELOPED LENGTH C.
FIXTURE BRANCH
D.
INVERT
106. Ratio of water closets for male population for elementary and secondary school A.
RATIO OF 1:35
B.
RATIO OF 1:20
C. RATIO OF 1:30 D.
RATIO OF 1:40
107.
A circuit vent which loop backs to connect with a stack vent instead of a vent stack Any vent connecting a horizontal branch or fixture drain with the stack vent of the originating waste or soil stack
A. LOOP or CIRCUIT VENT B.
LOCAL VENT
C.
CIRCUIT VENT
D. UNIT VENT
1.
What fitting is required to join copper with galvanized pipe?
A. Adaptor B. Coupling C. Dialectric Union D.
Solder Joint
E.
None of the above
2.
What is the diameter of a lavatory tailpiece?
A.
1 1/4"
B. 1 1/2" C.
1 3/4"
D. 2" E.
None of the above
3.
What size of P-Trap is required for a kitchen sink?
A.
1"
B. 1 1/4" C.
1 1/2"
D. 1 3/4" E.
None of the above
4.
What is the name of the fitting that connects the P-Trap to the drain?
A.
Union
B. Coupling C. Trap Adaptor D. Clamp E.
None of the above
5.
Name the trap assembly used when the drain is centered between both bowls of a kitchen sink.
A. Dual P-Trap Assembly B. Center Outlet Continuous Waste C.
End Outlet Continuous Waste
D.
Middle Sink Assembly
E.
None of the above
6.
Name the trap assembly used when the drain is centered under one bowl of the kitchen sink.
A. Center Outlet Continuous Waste B. End Outlet Continuous Waste C. Under-the- Sink Assembly D.
Single Trap Assembly
E.
None of the above
7.
What prevents gases from entering a home or building?
A. Back Flow Preventer B. Anti-Syphon Valve C. P-Trap D. Atmospheric Pressure E.
None of the above
8.
What is the minimum size drain for a water closet?
A.
1 1/2"
B.
2"
C.
3"
D. 4" E.
None of the above
9.
What size of drain is required for a combination tub/shower?
A.
1 1/2"
B.
2"
C.
3"
D. 4" E.
None of the above
10.
What size of drain is required for a shower stall?
A.
1 1/2"
B.
2"
C.
3"
D. 4" E.
None of the above
11.
What size of drain is required for a washing machine?
A. 1 1/2" D. 4" E.
None of the above
B.
2 "
C.
3"
.
(401) What wall thicknesses are available in copper tubing for drinking water?
A. A, B, C, D B. N, O, P,
DWV C.
K, L, M, DWV
D. Schedule 40 and 80
2.
(401) Galvanization provides a pipe with what benefit?
A.
Reduces corrosion
B. Makes the pipe easier to bend C. Increases pipe thickness D. Increases pipe strength
3.
(402) What fitting joins pipes so they can be taken apart later?
A.
Union
B. Nipple C.
Adapter
D. Coupling
4.
(402) How do street elbows and standard elbows differ?
A. Standard elbows have male threads B.
Street elbows have recessed threads
C. Standard elbows have tapered threads D.
Street elbows have one female and one male end
5.
(402) hows do copper pressure fittings differ from copper drain, waste, and vent (DWV) fittings?
A.
DWV fittings are threaded
B. Pressure fittings are threaded C. DWV fittings have a short radius sweep D. Pressure fittings have a deeper solder pocket
6.
(403) What is the smallest increment on most of the tape measures in our trade?
A. Sixty-fourth inch B.
Thirty-second inch
C. Sixteenth inch D. Eighth inch
7.
(403) What is the next largest sixteenth-inch mark after 3/4?
A.
15/16ths
B.
13/16ths
C.
10/16ths
D. 9/16ths
8.
(404) Convert 7 feet to inches.
A.
60 inches
B.
72 inches
C.
84 inches
D.
96 inches
9.
(405) What kind of tape measurer can you use to determine the travel when the offset angle is known to be 45 degrees?
A. Angle rule B. Travel rule C. Standard rule D. Plumber's rule
10. (406) How do you determine the center of a fitting? A.
By reading the branch, then the run
B.
By determining the angle of the branch
C. By dividing the length of the fitting by 2 D. By finding where lines drawn through the fitting intersect
11.
(406) An end-to-center measurement is made from the?
A. Middle of the pipe to end of fitting B.
End of pipe to center of fitting
C.
Center of pipe to end of fitting
D.
End of face to center of back
12. (407) When cutting tubing with a tubing cutter, how far do you turn the handle after each revolution? A.
1/8 turn
B. 1/4 turn C. 1/2 turn D.
1 full turn
13. (407) To remove the burr from inside a piece of pipe, operate the handle of the reamer with? A. Short, even, counterclockwise strokes B. Long, even, counterclockwise strokes C.
Long, even, clockwise strokes
D. Short, even, clockwise strokes
14. (408) What diameter steel pipe sizes are you able to thread with a nonadjustable ratchet style hand threader A. 1/8 - 2 inches B. 1/8 - 4 inches C.
1/2 - 2 1/2 inches
D. 1/2 - 3 inches
15.
(408) When threading steel pipe with a hand threader, how often do you apply oil to the pipe dies?
A.
When the dies squeak
B.
Before and after cutting threads
C. Every two or three downward stokes of the die handle D.
Once, at the halfway point of the threading operation
16.
(408) What is the purpose of oiling while threading the steel pipe?
A. Allows the pipe dies to turn freely inside the die holder B. Prevents the dies and threads from overheating and becoming damaged C.
The oil penetrates the pipe walls, slows down the corrosion process, and allows increased pipe life
D.
The oil maintains a thin protective coating on the pipe and prevents flying debris from injuring the user
17.
(409) When threading a fitting on a pipe, what happens if you overtighten a fitting?
A.
Leaks will be stopped completely
B.
The wrench you are using might break
C. Overall pipe length decreases by 1 inch D. The fitting stretches and the joint leaks
18.
(409) What size pipe wrench do you use on a 1/4 inch pipe?
A. 4 inch B. 8 inch C.
10 inch
D.
12 inch
19. (410) What preparation must you make to produce a good bond between the base metal and the solder in a copper soldered joint? A.
The solder must be lead free
B. The pipe must be reamed and cut C.
The solder must be 95/5 solder
D. The metal surfaces must be perfectly clean at the joint
20. (410) How much solder is needed to solder a 1/2 inch connection A. 1/2 inch B. 3/4 inch C. 7/8 inch D. 1 inch
21. (411) When using a lever type tubing bender, you can make angles up to how many degrees? A.
45 degrees
B. 90 degrees C. 120 degrees D.
180 degrees
22. (411) What action creates an watertight and airtight seal on a ferruled joint? A. Tighten the nut which crimps the ferrule into the tubing and against the fitting B.
The capillary action between the components
C.
Squeezing the ferrule into the nut
D. The compression of the tapered threads
23. (412) What is one disadvantage of the no-hub drainage system? A.
No-hubs have a tendency to leak
B.
More tools are required to make this type of joint
C. Support around the pipe may be required D. The pipe ends must be reinforced to ensure they do not crush under pressure
24. (412) When solvent welding plastic pipe, how do you insert the pipe into the fitting? A.
Put the pipe halfway into the fitting to allow for expansion and contraction
B.
Quickly insert the pipe into the fitting with a one-quarter turning motion
C.
Insert the pipe into the fitting and give the pipe a full turn
D. Thread the pipe into the fitting until no threads show
25. (412) How is large underground plastic pipe joined?
A.
Solvent welding
B. O-ring joints C.
Tig welding
D. Threading
26. (413) What are two types of pumps used in booster stations? A.
Deep well and split case
B. Booster and clear well C.
Split case and booster
D. Recirculating and clear well
27.
(413) What is the reason we use elevated storage tanks in water systems?
A.
Because of emergency water requirements
B. Elevated storage tanks provide cheap pressure C. Ground tanks are for firefighting purposes only D.
Elevated tanks last longer than ground storage tanks
28. (414) What element of a water meter translates the action of the water flow? A. Primary B. Secondary C. Tertiary D.
Head area
29.
(415) What is the minimum burial depth for water mains under roads?
A. 2 feet
B.
3 feet
C. 4 feet
D.
5 feet
30. (415) What is the part of the water distribution system that originates at the street main and extends into the building? A.
Water mains
B. Distribution mains C. Water service lines D. Lateral water mains
31. (415) Before a new water main is put into service it must be? A. Cured and tested B. Tested and leveled C.
Leveled and disinfected
D. Tested and disinfected
32.
(416) What Air Force form is used to maintain a record of each hydrant and its isolation valve?
A. AF Form 996 B. AF Form 997 C. AF Form 998 D. AF Form 1027
33.
(416) If the water level in a fire hydrant barrel rises after the hydrant is shut off, then?
A.
The weep hole is plugged
B. The main valve is leaking C.
There is a loose packing gland
D. There is too much residual pressure
34.
(417) What is the normal operating pressure of a water distribution system?
A. 5 to 10 pounds per square inch B. 10 to 20 pounds per square inch C. 40 to 75 pounds per square inch D. 100 to 200 pounds per square inch
35. (417) Which instrument is used to measure velocity flow from a fire hydrant? A. Pitot tube B. Vacuum gauge C.
Pressure gauge
D.
Hydrant gauge assembly
36.
(417) After you have taken all the hydrant readings, you should shut down the hydrants slowly to?
A. Decrease flushing time B. Prevent surges in pressure C.
Increase flushing time
D.
Increase the pressure throughout the system
37. (418) One of the factors to consider when sizing the supply for a building is the type of? A. Fixture style B. Flush devices C.
Service mains
D. Supply piping
38. (418) To solder copper joints in a water distribution piping, you must not use solder containing? A.
Less than 0.2 percent lead
B. More than 0.2 percent lead C.
Less than 0.2 percent antimony
D.
More than 0.2 percent antimony
39.
(418) How are building water distribution branch lines normally installed?
A. Horizontally, with a slight grade toward the shutoff valve B.
Horizontally, with a slight grade toward the point of use
C.
Vertically, with a slight grade toward the shutoff valve
D. Vertically, with a slight grade toward the point of use
40.
(418) What device do you install in a building distribution system to correct a water hammer problem?
A. Vertical air chamber B. Horizontal air chamber C. Vertical expansion fitting D.
Horizontal expansion fitting
41.
(419) The first step in the rough-in of fixtures is to locate the?
A. Main stack opening B.
Vertical trap position
C. Sewer and water line locations D. Exact position of the opening for each fixture
42. (419) Where on the studs should you cut holes for water supply lines? A. Top B.
Bottom
C.
Center
D. Corner
43. (419) To reinforce a structural beam that has been undercut? A Wedge a block in the notch and nail it in place
. B. Toenail four nails at angles to hold the pipe securely in place C. Cover the opening with a half-inch wooden strip and nail it in place D. Place a strap iron brace across the notch and fasten it with lag screws
44.
(420) When hanging steel pipe, place hangers no further apart than?
A. 4 feet
B.
6 feet
C.
10 feet
D.
12 feet
45. (420) How many feet apart should 1 1/2 inch diameter horizontal copper tubing be supported? A. 4
feet B.
6 feet
C. 8 feet
D.
10 feet
46. Plastic pipe and tubing must be supported evert? A. 4
feet B.
6 feet
C. 8 feet
D.
10 feet
47.
(421) the primary purpose of periodic testing of water mains for flow and pressure is to ensure that?
A.
Sufficient water is available for fire fighting
B.
The water system can meet the public demands for water
C.
Firefighters know how much water a hydrant can produce in inches of mercury
D.
Firefighters know how many pounds per square inch the system can usually provide
48. (421) Who must be notified anytime a water main is turned off? A.
Base operations
B.
Command post
C. Service call desk D.
Fire department
49.
(422) How many times are pipes in the water systems tested?
A. Once, after the fixtures are installed B.
Once, after rough-in is completed
C. Twice, after rough-in and after fixtures are installed D.
Twice, after the fixtures are installed and after the appliances are connected
50. (422) How much air pressure should you use for testing piping for leaks? A. 20 psi B.
30 psi
C.
40 psi
D 50 psi
.
51. (422) What can you use as a substitute for soapy water when leak-testing pipe during freezing weather? A. Pine oil B.
Linseed oil
C. Turpentine D.
Petroleum jelly
52.
(423) When winterizing a system, what is the first step in draining a water system?
A. Disconnect the unions B. Close the main shutoff valve C. Open the highest level faucets D.
Loosen at the lowest connection
53.
(423) Which antifreeze solution should be your first choice when you are protecting fixture traps against freezing?
A. Glycol B. Alcohol C. Glycerin D. Clacium chloride
54.
(424) When using a torch to thaw frozen pipes near wooden structures, you must isolate the area with a?
A.
Wet rag
B. Fire sheild C.
Heat shield
D.
Bucket of water
55. (424) The best way to thaw short length of frozen pipe up to 1 1/2 inches in diameter is to use? A.
Torches
B. Electric thawers C.
Hot water and rags
D. Rubber hose and funnel
56. (425) What is the proper way to tighten bolts on a full circle clamp? A. Working from the center out B. Working from the outside in C.
Tightening every other bolt
D. The tightening sequence doesn't matter
57.
(425) What type of repair clamp should be used as a temporary repair?
A. Unions B. No hub clamps C. Compression coupling D. Emergency pipe clamp
58. (425) When installing a compression coupling, why do you dig out the area to give you as much flexibility with the pipe? A.
To allow for easy installation
B. To check if the pipe has shifted C. To check if the water is shut-off D. To look for the cause of the break
59.
(426) In which order is a water main disinfected?
A.
Flushing, dosing, flushing, testing
B. Flushing, dosing, testing, flushing C. Dosing, flushing, testing, flushing D. Dosing, testing, flushing, testing
60. (426) What is the proper length of time and velocity for flushing a main?
A. 10 minutes/5.0 feet per second B.
15 minutes/5.0 feet per second
C. 20 minutes/2.5 feet per second D. 30 minutes/2.5 feet per second
61. (426) Which disinfection method is preferred on new water mains because of its simplicity and ease of use? A.
Sodium hypochlorite tablets
B. Calcium hypochlorite tablets C. Sodium hypochlorite powder D. Calcium hypochlorite powder
62.
(426) What is the correct chlorine dosage and contact time for disinfecting a water main?
A. 25 ppm/24 hours B. 25 ppm/12 hours C.
50 ppm/24 hours
D.
50 ppm/12 hours
63.
(427) What type of drainage system collects water from rain and melting snow?
A.
Main sewer
B. Storm sewer C.
Industrial sewer
D. Interceptor sewer
64.
(427) At what intervals are manholes usually places in sewer mains?
A.
200 to 400 feet
B. 300 to 500 feet
C.
350 to 550 feet
D.
400 to 600 feet
65.
(427) What may happen if a sewer pipe is laid with a fall greater than 1/4 inch per foot
A.
Reduction in pipe size is required to slow sewage
B.
The greater the fall, the better the operation of the sewer
C.
Sewage flow is slowed, causing sewage to settle in low spots
D.
Waste water runs away from solids, eventually causing stoppages
66.
(428) What is the desired fall for a 3-inch house sewer?
A.
1/8 inch per foot
B.
1/4 inch per foot
C. 1/2 inch per foot D.
1 1/16 inch per foot
67. (428) The proper fall for a house sewer is established by? A.
Using proper backfilling procedures
B.
Installing the proper shoring in the trench
C.
Establishing a grade line then digging the trench to exactly this line
D.
Joining the pipe aboveground before you lower it into the excavation and backfill
68. (428) in constructing a sewer main, when should you backfill the trench?
A. As soon as you install the pipe B. After you inspect the sewer pipe C.
As soon as the pipe has settled and shifted
D. After you remove all debris from the sewer pipe
69.
(428) What is the most important reason for backfilling a trench after pipe installation?
A. Eliminate an eye sore B.
Eliminate a safety hazard if left open
C.
Restore the natural appearance of the ground surface
D.
Protect the pipe from the movement and breakage due to backfill load
70. (428) For best results how should you backfill a trench? A. Manually backfill and tamp when full B.
Backfill with a backhoe and tamp when full
C. Backfill in layers of not more than 12 inches and tamp by hand D.
Backfill in layers of not more than 4 inches and tamp with a mechanical tamper
71. (429) The building sewer is usually made of clay tile, cast-iron, asbestos-cement, or? A.
Steel pipe
B. Rubber pipe C.
Plastic pipe
D.
Galvanized pipe
72. 29) What is the name of a short piece of pipe with a hub at one end and a straight cut or 45 degree cut on the other end that is used to tap into a sewer main? A.
Elbow
B.
Union
C.
Thimble
D. Coupling
73.
(429) Which type of sewage lift station houses the pumps and motors in a different compartment than the one that receives the wastewater?
A.
Dry well
B.
Wet well
C.
Dry pit
D. Wet pit
74.
(430) What are the two classes of drainage piping?
A. Soil and waste B.
Soil and plastic
C.
Plastic and steel
D. Steel and waste
75.
(430) Which type of drainage piping only conveys liquids that are free of fecal matter?
A.
Soil
B. Waste C. Vent D.
Traps
76.
(431) In a building drainage system, what is the definition of a stack?
A.
Vertical pipe of a system of soil, waste, or vent piping that extends through one or more stories
B. Horizontal pipe of a system of soil, waste, or vent piping that extends through one or more stories C.
Main artery of the venting system to which vent branches may be connected used primarily in multistory buildings
D. Pipe that is installed to vent a single fixture trap and which connects with the vent system above the fixture served or terminates in the open air
77. (431) How does a soil stack differ from a waste stack? A.
A soil stack is horizontal piping; whereas, a waste stack is vertical piping
B. A soul stack is vertical piping; whereas, a waste stack is horizontal piping C.
A soil stack carries the human fecal discharge of water closets, urinals, or other similar fixtures to the building drain; whereas, a waste stack carries waste that is free of fecal matter from all fixtures
D.
A waste stack carries the human fecal discharge of water closets, urinals, or other similar fixtures to the building drain; whereas, a soil stack carries waste that is free of fecal matter from all fixtures
78.
(431) What is used to determine the size of the stack after the fixture unit values have been totaled?
A. Fixture chart B. Fixture table C.
Stack chart
D. Stack table
79. (431) When you install an individual vent, how many inches must the vent piping rise above the fixture flood rim before it changes direction? A.
2
B.
3
C.
4
D.
6
80.
(431) What is the minimum sized pipe that you can use for a wet vent?
A.
1 1/4 inch
B. 1 1/2 inch C. 2 inch D. 3 inch
81. (432) How do you repair a leak on a plastic pipe fitting? A. Duct tape around fitting B.
Apply glue around fitting
C.
Apply primer around fitting
D. Cut fitting out and install new fitting
82. (433) What are the primary means of inspecting and maintaining the sewer system? A. Cleanout B. Manholes C. Sewer snakes D. Power rodders
83.
(433) What is used to remove ice from a manhole cover?
A.
Torches
B. Steel tools C. Iron tools D. Nonsparking tools
84. (433) What should you do if an oxygen-deficient condition is present in a manhole? A. Enter it B. Call the fire department C. Get and oxygen cylinder from base supply D. Ventilate it or use a self-contained breathing apparatus
85. (434) What is the correct method of disposal for discarded grease, fats, and oils? A. Dissolve with chemicals B.
Throw away into garbage
C. Dump into oil/water seperator D.
Flush down drain with hot water
86.
(434) Chemical drain cleaners are appropriate when the drains are?
A.
Flowing sluggishly
B. Completely stopped up C. Completely clogged with hair D. Completely clogged with grease
87.
(435) When do you perform recurring maintenance on a sewer main?
A. Monthly B. Quarterly C. Biannually D.
Annually
88. (435) What propels the nozzle of a jet rodder throughout the length of a sewer line? A. Hydraulic lever B. Hose reel assembly C.
Clockwise action of the drum
D. Reverse jet action of the nozzle
89.
(435) To repair a broken sewer main where should you block off the manhole?
A. Inlet side B. Outlet side C.
Gravity side
D.
Pressure side
90. (436) What is used to find the location of fixtures in a building? A.
Plot plan and as builts
B. Base utility map and plot plan C. Plumbing blueprints and floor plans D. As builts and manufacturer's instructions
91. (436) What is the smallest drain used in lavatories? A. 1 1/4 inches B. 1 1/2 inches C.
2 inches
D. 2 1/2 inches
92. (436) What is the size of trap used with the pop-up drain tailpiece? A. 1 1/4 inches B. 1 1/2 inches C.
2 inches
D. 2 1/2 inches
93.
(436) What is the name of the special tool designed to reach the hex jamnut beneath a fixture?
A.
Pipe wrench
B.
Box wrench
C. Basin wrench D. Adjustable wrench
94.
(437) What size supply is required for a flushometer-type water closet?
A.
1/4 inche
B.
1/2 inche
C.
3/4 inche
D. 1 inche
95.
(437) Tank water closets are preferred over flushometer water closets for residences because they?
A.
Are less expensive
B. Flush more quickly C. Require a smaller drain D. Require a smaller size supply
96. (437) What is the smallest plastic drain that can accommodate a water closet? A. 2 inches B.
3 inches
C.
4 inches
D.
6 inches
97.
(438) When specifications are not available, install the urinal so the lip height is?
A.
10 to 15 inches above the finished floor line
B. 20 to 25 inches above the rough floor line C. 20 to 25 inches above the finished floor line D. 20 to 25 inches below the finished floor line
98.
(438) What is the minimum size plastic waste pipe that you can use on a urinal?
A. 1 1/2 inches B. 1 3/4 inches C.
2 inches
D.
3 inches
99. (439) The tub overflow and drain assembly is not included in the rough-in piping for a bathtub because it is attached directly to the? A.
Tub at the time the tub is set
B. Vent at the time the tub is set C. Diverter at the time the tub is set D. Shower arm at the time the tub is set
100. (440) The distance between the floor and the drain board in a kitchen sink should be? A.
12 inches
B.
24 inches
C.
36 inches
D.
48 inches
101.
(440) What type of sink is used for dumping mop buckets and washing mops?
A.
Service sinks
B. Scullery sinks C. Kitchen sinks D. Countertop sinks
102. (441) What is installed on fixtures to keep sewer gases from entering the building? A.
Valves
B. Faucets C.
Vents
D.
Traps
103. (441) What is the water depth of a common seal trap? A. 2 inches B 4 inches
. C.
6 inches
D.
12 inches
104.
(442) If a faucet closes with the pressure; not against it, the result is?
A.
Harder operation and a tighter seal?
B.
Easier operation and a tighter seal?
C.
More frequent repairs and harder operation
D.
More frequent repairs but easier operation
105.
(442) What part of the body-unit faucet virtually eliminates maintenance of the faucet under normal operations?
A. Body unit B. Wearing washer C.
Stainless steel seat
D.
Ceramic component
106. (442) What does continuous dripping of a single or mixing faucet indicate? A. Bad washer B.
Damaged handle
C.
Low water pressure
D. Angle stop leaking
107. (443) Which shower/bath mixing valve is sensitive to both temperature and pressure? A. Pressure-controlled mixing handle B.
Double-handled mixing valve
C. Triple-handled mixing valve D.
Thermostatic mixing valve
108. (444) What size water supply line is required for urinal flushometers? A. 1/2 inch B. 3/4 inch C. 1 inch D.
1 1/2 inch
109.
(444) What size water supply line is required for water closet flushometers?
A. 1/2 inch B. 3/4 inch C. 1 inch D.
1 1/2 inch
110. (444) What are the two most commonly used flushometer valves? A. Piston and vacuum B. Piston and diaphragm C.
Hydraulic and vacuum
D.
Hydraulic and diaphragm
111.
(445) How do you repair a water closets leaking flapper?
A. Replace chain B.
Replace flapper
C.
Adjust rod guides
D.
Lightly sand with emery cloth
112. (446) A drinking fountain bubbler opening should be located above the drinking fountain rim a minimum of? A. 1 inch B.
2 inches
C.
3 inches
D.
5 inches
113. (447) Why must grease traps be installed in large military or commercial kitchens? A. A properly installed trap will prevent stoppages caused by grease solidification B. It is easier to dispose of grease into a trap and collect it there rather than a barrel C.
To collect the grease stir it up well before discharge into the sanitary system
D. In most states, local laws dictate that grease must be collected and dumped in a landfill
114. (447) Where should a grease trap be installed? A. As far away from the fixture as possible B. As close to the fixture as possible, preferably inside the building C. As close to the fixture as possible, preferably outside the building D. As close to the fixture as possible, preferably 50 feet outside the building
115.
(448) How is oil and water separated in oil water separators?
A.
Physical and manual
B.
Chemical and manual
C. Physical and chemical D.
Chemical and supervised
116.
(448) According to stokes law of physics, approximately how many inches will a 100-micron diameter droplet of oil rise in water every 10 minutes?
A.
4
B.
6
C.
8
D.
10
117. (448) On what type of as-built drawings are oil water separators located? A. Utility B.
Electrical
C.
Mechanical
D. Environmental
118. (449) What is the normal working pressure of a gas water heater? A.
125 psi
B.
150 psi
C. 200 psi D. 300 psi
119. (449) A drop tube in a water heater causes the incoming cold water to mix with? A. Outgoing hot water in pipes B. Outgoing cold water in the discharge C.
Stored hot water in the bottom of the tank
D. Stored cold water in the bottom of the tank
120. (449) The drain cock with a hose connection at the bottom of a water heater is primarily used to? A. Bypass the water heater B.
Flush sediment out of the heater
C.
Connect cold water into the heater
D.
Provide hot water access for washing equipment
121.
(449) The anode rod is installed in the top of water heaters to prevent corrosion?
A.
Inside the tank
B. Outside the tank C. Of the hot water supply D. Of the cold water supply
122.
(450) A domestic food grinder is designed to attach to a drain with a diameter of
A. 1 1/4 inches B. 1 1/2 inches C.
2 inches
D. 2 1/4 inches
123. (450) How is water allowed to enter an industrial food grinder? A. Faucet B.
Solenoid valve
C. Pressure switch D.
Pressure reducing valve
124.
(451) What is the minimum size water supply for a drench-type emergency shower and eye wash?
A. 1 inch or less B. 1 1/8 inches C.
1 1/4 inches
D.
2 inches
A term synonymous with faucet, cock, plug, tap or spigot A. battery of fixtures B.
bell or hub
C.
bibb
D. branch
2.
Any part of the piping system other the main, riser or stack
A. battery of fixtures B.
bell or hub
C.
bibb
D. branch
3.
The flow of water or waste water in pipes in reverse direction from that normally intended
A.
air break
B. air gap C. angle valve D. backflow
4.
The end portion of a pipe which for a short distance is enlarged to recieve the end of another pipe which may be the same diameter for the purpose of making a joint
A. battery of fixtures B.
bell or hub
C.
bibb
D. branch
5.
A valve in which the inlet and outlet openings are at 90 degree angle to one another
A.
air break
B. air gap C. angle valve D. backflow
6.
That part of the drainage system that extends from the end of the building drain and conveys its discharge to the public sewer, private sewer, individual sewage disposal system or other appropriate point of disposal
A.
bidet
B.
branch interval
C. building/house drain D.
building/house sewer
7.
The first section of water supply piping in a building after the water meter
A. building supply pipe B.
caulking/calking/cogging
8.
Any group of two or more similar adjacent fixtures which discharge into a common horizontal waste or soil branch
A. battery of fixtures B.
bell or hub
C.
bibb
D. branch
9.
The unobstructed vertical distance through the free atmosphere between the outlet of a faucet and the flood level rim of the fixture or receptacle
A.
air break
B. air gap C. angle valve D. backflow
10.
A device installed in piping to prevent the reverse flow of storm or sewage into the drainage system or their branches
A. back pressure B. back siphonage C. backwater valve D. ball valve
11.
A pressure within the sanitary drainage system or vent piping system that is greater than the atmospheric pressure (>14.7psi)
A. back pressure B. back siphonage C. backwater valve D. ball valve
12.
A vertical length of soil or waste stack at least eight feet in height ( a storey hieght), within which the horizontal branches from one storey or floor of the building or structure are connected on the stack
A.
bidet
B.
branch interval
C. building/house drain D.
building/house sewer
13. The physical separation between a waste pipe and an indirect receptor or device indirectly connected A.
air break
B. air gap C. angle valve
D. backflow
14. A kind of fixture which is used for bathing the external genitals and posterior parts of the body A.
bidet
B.
branch interval
C. building/house drain D.
building/house sewer
15.
That part of the lowest horizontal piping of a plumbing system which recieves the discahrge from soil waste and other drainage pipes inside a building and conveys it to the building sewer/house sewer
A.
bidet
B.
branch interval
C. building/house drain D.
building/house sewer
16. The flowing by negative pressure of contaminated or polluted water from a plumbing fixture into a potable water system A. back pressure B. back siphonage C. backwater valve D. ball valve
17.
Plugging an opening with oakum lead or other material that are pounded into the annular space
A. building supply pipe B.
caulking/calking/cogging
18. A valve in which the flow of liquid is controlled by a rotating drilled ball that fits tightly against a resilient (flexible) seat in the valve body A. back pressure B. back siphonage C. backwater valve D. ball valve
.
A device which discharges a predetermined quantity of water of fixtures for flushing purposes and is actuated by direct water pressure
A. flushometer valve B.
full bath
C.
gate valve
D. globe valve
2.
A valve in which the floe of water is cut off by a means of a circular disk, fitting against machine-smoothe surfaces at right angles to the direction of flow. The disk is raised or lowered by the means of a threaded stem connected to the handle of the valve. The opening in the valve is usually as large as the full bore of the pipe
A. flushometer valve B.
full bath
C.
gate valve
D. globe valve
3.
Any pipe which carries wastewater or waterbone wastes in a building drainage system
A.
drain
B.
drainage fixture unit
C.
DWV
D. faucet
4. A receptacle attached to a plumbing system other than a trap in which water or wastes may be collected or obtained for ultimate into the plumbing system
A. fixture B. flood level C.
flow rate
D. flush valve
5.
A non watertight lined excavation in the ground which receives the discharge of a sanitary drainage system or part thereof, designed to retain the organic matter and solids discharging there from, but permitting the liquid to seep through the side and the bottom of it.
A.
cesspool
B. cleanout C.
conductor or leader
D. cross connection
6.
A fitting with a removable plate or plug that is placed in plumbing drainage pipe lines to allow access to the pipes for the purpose of cleaning and maintenance
A.
cesspool
B. cleanout C.
conductor or leader
D. cross connection
7.
A bathroom containing a water closet, a lavatory and a bathtub
A. flushometer valve B.
full bath
C.
gate valve
D. globe valve
8.
The vertical portion of a rainwater conductor
A.
deadend
B. developed length C. diameter D. downspout
9.
The level in a fixture at which water begins to overflow the top or rim of the fixture
A. fixture B. flood level C.
flow rate
D. flush valve
10.
Part of the roofing and/or gutter system that takes water from a roof above-surface area to a storm drain or other disposal area or system
A.
cesspool
B. cleanout C.
conductor or leader
D. cross connection
11.
A valve on a water pipe by means of which water can be drawn from or held within the pipe. The valve is placed on the end of the pipe
A.
drain
B.
drainage fixture unit
C.
DWV
D. faucet
12. A valve in which the flow of water is cut off by means of a circular disk that fits against the valve seat. The plane movement of the disk is parallel to the normal
direction of flow A. flushometer valve B.
full bath
C.
gate valve
D. globe valve
13.
A common measure of the probable discharge into the drainage system by various system of plumbing fixtures on the basis of one dfu being equal to the discharge rate of 7.5 gals per minute
A.
drain
B.
drainage fixture unit
C.
DWV
D. faucet
14.
The abbreviation for drainage waste and vent
A.
drain
B.
drainage fixture unit
C.
DWV
D. faucet
15.
The extended portion of a pipe that is closed one end to which no connections are made on the extended portion, thus permitting stagnation of waste water or air therein
A.
deadend
B. developed length C. diameter D. downspout
16. The normal commercial designation, normally the inside diameter of the pipe, unless otherwise specifically stated in a particular plumbing code A.
deadend
B. developed length C. diameter D. downspout
17.
The length along the center line of pipes and fittings
A.
deadend
B. developed length C. diameter D. downspout
18.
Any physical connection or arrangement of pipes between 2 otherwise separate building water supply pipes or system through which or by means of which water supply may flow from one system to the other, the direction of flow depends on the pressure difference between two systems
A.
cesspool
B. cleanout C.
conductor or leader
D. cross connection
19. The volume of water used by a plumbing fixture in a given amount of time. Usually expressed in gallons per minute (gpm) A. fixture B. flood level C.
flow rate
D. flush valve
20. A device located at the bottom of a flush tank for flushing water closet and similar fixtures A. fixture B. flood level C.
flow rate
D. flush valve
1.
Water that meets the standards of a government agency and is used for culinary, domestic and drinking purposes
A. Plumbing System B. Potable water C.
Privy
D. Public sewer
2.
An opening constructed in any part of the plumbing system, of sufficient size for a person to gain access thereto
A. Manhole B. Pipe C.
Plumbing
D.
Plumbing fixture/ Sanitary Ware
3.
A bathroom containing water closet and lavatory
A. Gooseneck B.
Half Bath
C.
Hose Bibb
D.
Indirect Waste Pipe
4.
An outside or structures used for the deposition of excrement
A. Plumbing System B. Potable water C.
Privy
D. Public sewer
5.
A water supply pipe that extends vertically one full storey or more to convey water to fixture branches or group of fixtures
A. Riser B.
Roughing-in
C. Seepage Pit/Cesspool/DryWell
6.
The art and science of installing in buildings the pipes, fixtures and other apparatus for bringing in water supply and removing water and waterborne wastes
A. Manhole B. Pipe C.
Plumbing
D.
Plumbing fixture/ Sanitary Ware
7.
A condition contrary to sanitary principles or injurious to health
A.
Insanitary
B.
Lavatory/Basin Wash
C. Main
D. Main Vent/Vent Stack
8.
The installation of parts of the plumbing system which can be completed prior to installation of fixtures or finishing. This includes drainage, water supply and vent piping and necessary fixture supports
A. Riser B.
Roughing-in
C. Seepage Pit/Cesspool/DryWell
9.
A loosely lined excavation in the ground, which receives the discharge of a septic tank to seep through the bottom and sides of the pit
A. Riser B.
Roughing-in
C. Seepage Pit/Cesspool/DryWell
10. The principal pipe to which the branches may be connected A.
Insanitary
B.
Lavatory/Basin Wash
C. Main D. Main Vent/Vent Stack
11.
A receptacle attached to a plumbing system other than a trap in which or wastes may be collected or retained for ultimate discharge into the plumbing system
A. Manhole B. Pipe C.
Plumbing
D.
Plumbing fixture/ Sanitary Ware
12.
A vertical vent pipe installed primarily for the purpose of providing circulation of air to or from any part of the building drainage system
A.
Insanitary
B.
Lavatory/Basin Wash
C. Main D. Main Vent/Vent Stack
13.
A kind of return bend of small-sized faucet, one end of which is about one foot long and the other end is about 3 inches. It is commonly used as a faucet for pantry sink and drinking fountain. Also the lead connection between the service pipe and the water main.
A. Gooseneck B.
Half Bath
C.
Hose Bibb
D.
Indirect Waste Pipe
14.
A common sewer directly controlled by public authority to which all abutters have equal rights of connections
A. Plumbing System B. Potable water C.
Privy
D. Public sewer
15.
A waste pipe that does not connect directly with the drainage system but conveys wastes by discharging into a plumbing fixture or receptable, which is directly connected to the drainage system
A. Gooseneck B.
Half Bath
C.
Hose Bibb
D.
Indirect Waste Pipe
16. All water supply, drainage, and venting systems and all fixtures and their traps complete with their connections
A. Plumbing System B. Potable water C.
Privy
D. Public sewer
17.
A cylindrical conduit or conductor, the wall thickness is sufficient to receive a standard pipe
A. Manhole B. Pipe C.
Plumbing
D.
Plumbing fixture/ Sanitary Ware
18. A fixture designed for washing of the hands and the face A.
Insanitary
B.
Lavatory/Basin Wash
C. Main D. Main Vent/Vent Stack
19. A faucet which a hose may be attached A. Gooseneck B.
Half Bath
C.
Hose Bibb
D.
Indirect Waste Pipe
Refers to the back flow of used contaminated or polluted water from a plumbing fixture or vessel into a water supply pipe due to negative pressure in such a pipe
A.
Back Siphonage
B. Back flow C.
back pressure
2.
Is a quantity in terms of which the load producing effects on the plumbing system of different kinds of plumbing fixtures are expressed on some arbitrarily chosen scale
A.
Fixture Units
B.
Fixture measure
C. Unit of Fixture
3.
Is a drain from two or three fixture connected to a single trap. It is also called a dual vent.
A.
Common Vent
B. Surface Vent C. Double Vent
4.
is any part of piping system other than the main riser or stack
A.
Branch
B.
Stack
C. Horizontal part
5. Is the minimum cross sectional area at the point of water supply discharge, measured or expressed in terms of diameter of a circle. If the opening is not a circle ,the
diameter of a circle that is equivalent the cross sectional area A. Effective Opening B. Surface Opening C. Supply Opening
6.
Is the unobstructed vertical distance through the free atmosphere between the lowest opening from any pipe or faucet supplying water to a tank, plumbing fixture , or other device and the flood level rim of the receptacle
A. Air Gap B. Air Space C.
Air Vant
7.
Is the flow of water, or other liquid mixture or substances into the distributing pipes of a potable supply of water from any source, other than its intended source
A.
Back Flow
B.
Back Siphon
C. Back pressure
8.
is a device located at the bottom of the tank for flushing water closets and similar fixtures.
A.
Flash Valve
B.
Flushometer Valve
C.
Relief Valve
9.
Is plugging an opening with an oakum, lead or other materials, that are pounded into place or opening.
A.
Caulking
B.
Oakuming
C. Plugging
10. Refers to any group of two or more similar adjacent fixtures which discharges into a common horizontal waste pipe or soil branch A.
Battery of Fixture
B.
Group of Fixture
C. branch of Fixture
.
Conveys only wastewater or liquid waste free of fecal matter
2.
Oversized pipe functioning both as a soil or waste pipe and a vent
3.
Layer of sewage matter that rises to the surface of the sewage in a septic tank
4.
A pipe or artificial conduit as underground for carrying off sewage or other liquid waste to a treatment plant.
5.
Any part of the piping system other than a main, riser or stack.
6.
'backbone' of the entire sanitary system. Portion where waste does not travel through.
A. main soil and waste stack B.
air vent and soil pipe
C main soil and waste vent
. D.
unit, common or dual vent
7.
Used for fixtures such as slop sinks that are usually built low in the ground.
A. deep seal trap B. stand trap C.
drum trap
D. common p-trap
8.
Most popular and generally specified material for drainage
9.
Where should the septic tank be located
A. not underneath the house B.
underneath the water distribution system
C.
underneath the house
D. at least 5 meters from the water distribution system E.
at least 10 meters from the water distribution system
F. at least 15 meters from the water distribution system G. at least 20 meters from the water distribution system
10. Minimum size trap for residential sink A. 38mm B. 32mm C.
36mm
D. 34mm
11. What pipe is used for underground installations A.
UV type
B.
SV type
C. XV type D.
SX type
12. 'Collecting Vent Line.'
13. Drawing: (Answers on 204-205, building construction:) 1. 45 degree Elbow 2.Return Bend 3.Wye 4. Sanitary Cross 5. Tee
14. Liquid content of sewage
15. Drawing (Answers on Page 195-196, building construction) 1. S-Trap 2. Common P-Trap
.
Receptacles which are used to provide, receive and discharge water.
A. Bath Fixtures B.
Scullery Fixtures
C. Soil Fixture D. Plumbing Fixtures
2.
identify according to flush type
A. Flush Tank Water Closet B. Direct Flush Valve C.
Close Coupled Flush Tank
D. Both a and b
3.
identify according to flush type
A.
High Flush Tank
B. Floor Mounted C. Low Flush Tank D. Integral Flush Tank
4. Toilet type according to flushing action that flushes through a siphon action created in the trapway. A.
Reverse Trap
B. Wash Down C. Siphon Jet D.
Siphon Vortex
5.
Has A Bulge in Front. Costs less but is least efficient and noisiest.
A.
Siphon Vortex
B. Reverse Trap
C. Wash Down D. Direct Flush Valve
6.
Label the missing parts. From Top to bottom
7.
Flushable Fixture Used By men for urinating
A. water closet B.
urinal
C. lavatory D.
bidet
8.
Device for regulating the supply of water in a flush tank by means of a hollow floating ball. also called float valve
A. ball cock B.
flushometer valve
C.
water hammer
D.
backsplash
9.
Flushing action is obtained directly from a flush valve connected into the bowl
A.
siphon jet
B.
wash down
C. wall hung D. direct flush valve
10.
Identify according to Flush Tank type
A.
High Flush Tank
B.
Low Flush Tank
C. Integral Flush Tank D.
Close Coupled Flush Tank
11. A 180 degree bend in a pipe. A. drop elbow B.
return bend
C.
elbow
D. wye
12. Oblong tub to bathe in.
13. Bath in which water is sparayed onto the body from an overhead nozzle or showerhead.
14. Bowl or basin with running water for washing the face or hands
15.
Deep sink for washing clothes
16.
Bar attached to a wall near a bathtub or shower
17.
U shaped or s shaped section of a drainpipe in which liquid remains and forms a seal for preventing the passage of sewer gas without affecting the normal flow of waste water or sewage.
A. drum trap B.
backsplash
C. air gap D.
trap
18. Coupling device for connecting two pipes. A. plug B. sanitary toe C.
union
D.
increaser
A. school of design established in Germany called "BAUHAUS" founded by A. a. Walter Gropius B. b.Peter Behrens C. c. Auguste Perret D. d. Louis Khan
2.
Art noveau is known as International Style, in Germany it is known as
A.
a. Ecole des Beaux
B.
b. Liberty
C. c. Chateaux D.
d. Judgendsstil
3.
1. What is a method of analyzing indeterminate modular building frames by assuming hinges at the center of beam spans and column heights?
A.
c. fee body diagram method
B. d. portal method C. a. cantilever method D. b. moment distribution method
4.
1. Two M.S. plates are to be welded by end butt joint by a partial penetration groove weld. The thickness of the plates are 16mm. What is the minimum effective throat thickness of the weld?
A. a. . 6.0 mm B. b. . 9.0 mm C. c. 7.5 mm D. d. 12.0mm
5.
1. How is a camber treated in a steel truss 25 meters or longer?
A. a. Camber shall be approximately equal to 1% of the span. B. b. Camber shall be approximately equal to the dead load deflection. C. c. • C. Camber shall be approximately equal to 0.8% of the span plus 1/3 the dead load deflection. D.
d. Camber shall be approximately equal to 0.5% of the span plus 1/3 the live load deflection.
6.
1. Which of the following criterion is not applicable for plug and slot welds?
A. a. The thickness of plug or slot welds in material 16mm or less in thickness shall be equal to the thickness of the material. B. b.The minimum center to center spacing in a longitudinal direction of any line shall be 2 times the length of the slot. C.
c. . The thickness of plug or slot welds in material over 16mm in thickness shall be at least 1/2 the thickness of the material but not less than 16mm.
D. d.The width of the slot shall not be less than the thickness of the parts containing it plus 10mm nor 2 1/4 times the thickness of the weld.
7.
1. What is a round, steel bolt embedded in concrete or masonry used to hold down masonry, steel columns, or beam casting, shock beam plates and engine heads?
A. a.retaining bolts B. b. foundation bolts C. c. anchor bolts D. d. friction bolts
8.
1. What are piles placed at an inclination to resist forces that are not critical?
A. a. guide piles B. b.batter piles C. c.slope piles D.
d. fender piles
9.
1. What is a material other than water, aggregate or hydraulic cement, used as an ingredient of concrete and added to concrete before or during its mixture to modify its properties?
A. a. admixture B.
b.steam
C. c.plasticizer D.
d. retarder
10. 1. What is a concrete beam placed directly on the ground to provide foundation for the superstructure? A. a. trap beam B.
b. gerber beam
C.
c. grade beam
D. d. tie beam
11.
1. What is the act of excavating or filling of earth or any sound material or combination thereof, in preparation for a finishing surface such as paving?
A. a. cut and fill B. b. grading C.
c. site preparation
D.
d. benching
12. What are piles placed at an inclination to resist forces that are not critical? A. a. guide piles B. b. batter piles C.
c. slope piles
D.
d. fender piles
13. Which of the following criterion precludes good construction practice for conduits and pipes embedded in concrete? A. a. Conduits and pipes embedded in slab, the wall or beam shall not be larger in outside dimension than 1/3 the overall thickness of slab, wall or beam in
which they are embedded. B.
b. Reinforcement with an area not less than 0.002 times the area of cross section shall be provided normal to piping.
C.
c. Conduit and pipes, with their fittings, embedded within a column, shall not displace more than 5% of the area of the cross section on which strength is calculated.
D.
d. Concrete cover for pipes, conduits and fittings, shall not be less than 40mm for concrete exposed to earth or weather.
14.
What is the minimum requirement for development of at least 1/3 of the total reinforcement provided for negative moment reinforcement, as an embedded length beyond the point of inflection?
A.
a. Not less than the effective length of member of 12 db, or 1/16 of the clear span, whichever is greater.
B.
b. L/3 + d or 24 db, or 1/12th the clear span, whichever is greater
C.
c. Not less than 1.5d or 14db, or 1/12th the clear span, whichever is greater
D.
d. L/4 + d or 12 db, or 1/12th the clear span, whichever is greater
15.
As a seismic requirement for flexural members where hoops are required, how are the remaining portions of a beam treated with transverse reinforcement as minimum requirement other than those required with hoops?
A.
a. Where hoops are not required, stirrups shall be spaced at no more than d/2 throughout the length of the member.
B. b. Where hoops are not required, cross ties shall be spaced at no more than d/3 throughout the length of the member. C.
c. Where hoops are not required, hoops shall continue except that spacing shall not be more than d/2.
D.
d. Where hoops are not required, closed stirrups shall be spaced at no more than d/4 throughout the length of the member.
16. What is the minimum inside diameter of a standard hook for stirrups and ties for a 16m bar and smaller in diameter? A.
a. 8 db
B.
b. 6 db
C.
c. 4 db
D.
d. 10 db
17. What is the weight of 34 mmØ (32mmØ – 1 1/4 inØ) steel bar 9 meters long?
A. a. 40.636 kilograms B b. 51.388 kilograms
. C. c. 54.488 kilograms D.
d. 56.865 kilograms
18.
What is the minimum concrete cover for primary reinforcement of beams and columns not exposed to earth or weather for precast concrete manufactured under plant control conditions?
A.
a. db but not less than 25mm.
B. b. db but not less than 15mm and need not exceed 40mm. C. c. db but not less than 20mm and need not exceed 50mm. D. d. db but not less than 30mm.
19.
The tendency of most materials to move or deform over time under a constant load. The amount of movement varies enormously depending upon the material. The area that is highly stressed will move the most. The movement causes stresses to be redistributed.
A.
a. . creep
B.
b. deflection
C. c. buckling D.
d. fatigue
E. e. overload
20.
Accounted for in concrete design using reduced modulus of elasticity is
A. a. the effect of creep on deflections due to sustained loadings B. b. the effect of cracks on the tension side C. c. the effect of yield line patterns on members D.
d. the effect of stirrup reinforcement on axial loads
21.
In computing for the slenderness ratio of steel compression members, what takes into account the effect of the degree of restraint at the top and bottom supports?
A. a. K-factors B. b. Radius of gyration C. c. Length D.
d. Cross-sectional area
22.
The strength reduction factor for the design strength of a member with axial tension and axial tension with flexure is as follows:
A. a. 0.70 B.
b. 0.90
C. c. 0.80 D. d. 0.75