platform: dball2 firmware honda56 - microsoft · pdf filevehicle application guide the...
TRANSCRIPT
Installation Guide
Update Alert: Firmware updates are posted the web on a regular basis. We recommendon
that you check for firmware and/or install guide updates prior to installing this product.
Vehicle Application Guide ....... .................. ..................................... ............................... ......................................................
Installation s s(Wiring Diagram & Vehicle Wiring Reference Chart )Type 1.............. ..... .................................................................................................................... ..........................................Type .............. ..... ..........................................2 .......................................................................... ..........................................Type .............. ..... ..........................................3 .......................................................................... ..........................................Type .............. ..... ..........................................4 .......................................................................... ..........................................Type .............. ..... ..........................................5 .......................................................................... ..........................................Type .............. ..... ..........................................6 .......................................................................... ..........................................
ProgrammingModule Programming ...................... .............................................................................. .......... ...........................................Module Reset.. ...................................................................................................................................................................Hard ... ....Reset.. ................................................................................................................................................................Feature & Option List..........................................................................................................................................................Feature Programming.........................................................................................................................................................
LED Diagnostics & Troubleshooting...................................................................................................................................
Limited One-Year Consumer ........Warranty.......................................................................................................................
Quick Reference Guide......................................................................................................................................................
02
030608101214
1619192020
21
23
24
Index
® Acura and Honda their respective companiesare registered trademarks and property of .
The 56 firmware for 2 is an all-in-one door lock and override module compatible withHONDA DBALLspecific Acura and Honda vehicles.
This module can only be flashed and configured using Xpress at www.directechs.com orVIPusing the Directechs Mobile application for smartphones. Refer to the Module Programmingsection son page 16 for more information.
No takeover feature is available on Push-to-Start vehicles.
Rev.: 20 727170
Platform: DBALL2
Firmware HONDA56:
© 2017 Directed. All rights reserved.
Vehicle Application Guide
The following table lists the vehicles and features which are compatible with this product. The number assigned to eachyear allows you to determine which installation type should be used for your vehicle.
* OEM Remote Keyless Entry does not operate when vehicle is remote started.
Page 2
Vehicles
2017
2016
2015
2014
2013
2012
2011
2010
2009
2008
PK
-Im
mobilizer
Bypass-D
ata
No
Key
Req'd
DL-A
rmF
acto
ryS
ecurity
DL-D
isarm
Facto
ryS
ecurity
DL-D
oor
Lock
Contr
ol
DL-D
oor
Unlo
ck
DL-D
river
Priority
Unlo
ck
DL-S
lidin
gD
oor
Contr
ol D
river
DL-S
lidin
gD
oor
Contr
ol P
assenger
DL-T
runk
/H
atc
hR
ele
ase
FO
B-C
ontr
ol o
fafterm
ark
etala
rmw
ith
OE
Mre
mote
RS
-RA
PS
hutD
ow
n(R
eta
ined
AC
C
Pow
er)
RS
-Tach
/R
PM
Outp
ut
SS
-Entr
yM
onito
ring
Hood
Pin
SS
-Entr
yM
onito
ring
Tru
nk/H
atc
hP
in
SS
-Facto
ryA
larm
Trigger
Monito
ring
ST
-Bra
ke
Sta
tus
(footbra
ke)
ST
-Door
Locks
Sta
tus
ST
-E-B
rake
Sta
tus
ST
-Igniti
on
Sta
tus
Acura
ILX (Smart Key) 6 6 6 • • • • • • • D • • • • D • D • •
RDX (Smart Key) 6 6 6 • • • • • • • D • • • • D • D • •
TL 1 1 1 1 1 1 • • • • • • • D • • • • D • D • •
TL (Smart Key) 2 2 2 2 2 2 • • • • • • • D • • • • D • D • •
TSX 1 1 1 1 1 1 • • • • • • • D • • • • D • D • •
ZDX 1 1 1 • • • • • • • D • • • • D • D • •
ZDX (Smart Key) * 3 3 3 3 • • • • • • • D • • • • D • D • •
Honda
Accord 1 1 1 1 1 • • • • • • • D • • • • D • D • •
Accord Crosstour 1 1 1 • • • • • • • D • • • • D • D • •
Civic 4 4 4 4 • • • • • • • D • • • • • D • •
CR-V 5 5 5 5 5 • • • • • • • D • • • • • D • •
Odyssey 1 1 1 1 1 1 1 • • • • • • • • • D • • • • D • D • •
Pilot 1 1 1 1 1 1 1 • • • • • • • D • • • • D • D • •
Legend: AV: Horn & Lights Controls
D: Data-to-Data (D2D) only CC: Comfort & Convenience Controls
•: D2D and Wire-to-Wire (W2W) DL: OE Door Lock & Alarm Controls
FOB: Sync CAN Interface w/ FOB Remote
PK: Transponder & Immobilizer Override
RS: Remote Start & Engine Controls
SS: Integrated Security & Monitoring
ST: Function/Feature Status
Rev.: 20 727170
Platform: DBALL2
Firmware HONDA56:
© 2017 Directed. All rights reserved.
[1] ( ) Tach InputAC
(+) Brake Input
(-) E-Brake Status Input
(-) Trunk Status Input
(-) Door Status InputR
em
ote
Sta
rter
(-) (Status)GWR
(-) OutputLock
(-) OutputUnlock
(-) Trunk Output
(-) Aux1 Output (Hatch glass release, if applicable)
(-) Ground
(+) Starter
(+) Accessory 2 (if needed)
(+) Accessory 1
(-) Parking Lights
[2](-) Factory Alarm Rearm
(+) 12V
(+) Ignition
(-) Hood Status Input
Immo. Data:pin 2
[3] Ignition:pin 6
Headlight Switch(White & Black conn.
at headlight)
(-) Parking Lights:pin 8
[2](-) Autolights:pin 9
6 5 4 3 2 1
712 10 9 811
Not required in D2D mode.
14 3 57 256
1: (-) Lock InputGreen:
2: (-) Unlock InputBlue:
3: (-) Trunk InputRed/White:
4: (-) Aux1 InputWhite/Violet:(Hatch glass release, if applicable)
10: (-) (Status) InputBlue/White: GWR
[1] ( ) Tach OutputAC : 5Violet/White:
(+) Brake Status Output: 6Gray:
(-) Door Status Output: 3Green/White:
(-) Trunk Status Output: 4Red/Black:
(-) : 10E-Brake Status Output Yellow/Black:
Immobilizer Data: 11Orange/Black:
(-) Hood Status Output: 12Blue/Red:
B- High:CANpin 4
B- Low:CANpin 3
HS CAN : 3High Tan/Black:
HS CAN : 4Low Tan:
FT CAN High: 5Orange/Green:
FT CAN : 6Low Orange/Brown:
1 8
169
F- LowCAN :or p 4Black Red, in 1
DiagnosticConnector OBDII(connector side view)
F- High p 6CAN : inWhite, Immobilizer Control Unit(Black conn. around ignition cylinder)
[3] Ignition Interrupt (conn. side) 8: Yellow:
[3] Ignition Interrupt (veh. side) 9: Orange/Yellow:
CUT
5 4 3
12
(+) Starter: pin 2
(+) Acc. 1:pin 5
(+) Acc. 2:pin 4
(+) Ignition:pin 3
(+) 12V: pin 1Ignition SwitchWhite Connector
(+) 12V: 13Red:(+) 12V
(-) Ground: 14Black:(-) Ground
P#: 2D65XKD
(-) Ground
(+)12V
Installation Type 1
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
With the exception of the Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII
[2] Connect the Rearm wire if the vehicle is equipped with automatic headlights.only
10
2DBALL
RF
Prog. Button
LED
4
14
12
2
TX
RX
[3] Optional but required for OEM Remote Keyless Entry to operate when vehicle is remote started.
Page 3
Rev.: 20 727170
Platform: DBALL2
Firmware HONDA56:
© 2017 Directed. All rights reserved.
Rev.: 20 727170
Platform: DBALL2
Firmware HONDA56:
© 2017 Directed. All rights reserved.
Type 1 - Vehicle Wiring Reference ChartPage 4
Function Color Pin Polarity Location Color Pins
Acura TL 2009-2014
12V White 1 (+) Ignition switch. White 5
Starter Yellow 2 (+) Ignition switch. White 5
Ignition Blue 3 (+) Ignition switch. White 5
Accessory Green 5 (+) Ignition switch. White 5
Immobilizer Data Lt. Green 2 Data Immobilizer control unit around ignition cylinder. White 7
Immobilizer Ignition Interrupt Yellow 6 (+) Immobilizer control unit around ignition cylinder. White 7
B-CAN High Pink 4 Data Immobilizer control unit around ignition cylinder. White 7
B-CAN Low Blue 5 Data Immobilizer control unit around ignition cylinder. White 7
Parking Lights Gray 8 (-) Headlight Switch. Black & White 12
F-CAN High White 6 Data OBDII. Black 16
F-CAN Low Red or Black 14 Data OBDII. Black 16
Acura TSX 2009-2014
12V White 1 (+) Ignition switch. White 5
Starter Yellow 2 (+) Ignition switch. White 5
Ignition Blue 3 (+) Ignition switch. White 5
Accessory Orange 5 (+) Ignition switch. White 5
Immobilizer Data Lt. Green 2 Data Immobilizer control unit around ignition cylinder. Black 7
Immobilizer Ignition Interrupt Yellow 6 (+) Immobilizer control unit around ignition cylinder. Black 7
B-CAN High Pink 4 Data Immobilizer control unit around ignition cylinder. Black 7
B-CAN Low Blue 5 Data Immobilizer control unit around ignition cylinder. Black 7
Parking Lights Gray 8 (-) Headlight switch. Black & White 12
Autolights Red 9 (-) Headlight switch. Black & White 12
F-CAN High White 6 Data OBDII. Black 16
F-CAN Low Red or Black 14 Data OBDII. Black 16
Acura ZDX 2010-2012
12V White 1 (+) Ignition switch. White 5
Starter Yellow 2 (+) Ignition switch. White 5
Ignition Blue 3 (+) Ignition switch. White 5
Accessory Green 5 (+) Ignition switch. White 5
Immobilizer Data Lt. Green 2 Data Immobilizer control unit around ignition cylinder. White 7
Immobilizer Ignition Interrupt Yellow 6 (+) Immobilizer control unit around ignition cylinder. White 7
B-CAN High Pink 4 Data Immobilizer control unit around ignition cylinder. White 7
B-CAN Low Blue 5 Data Immobilizer control unit around ignition cylinder. White 7
Parking Lights Gray 8 (-) Headlight switch. Black & White 12
F-CAN High White 6 Data OBDII. Black 16
F-CAN Low Red or Black 14 Data OBDII. Black 16
Honda Accord 2008-2012
12V White 1 (+) Ignition switch. White 5
Starter Yellow 2 (+) Ignition switch. White 5
Ignition Blue 3 (+) Ignition switch. White 5
Accessory Orange 5 (+) Ignition switch. White 5
Immobilizer Data Lt. Green 2 Data Immobilizer control unit around ignition cylinder. White 7
Immobilizer Ignition Interrupt Yellow 6 (+) Immobilizer control unit around ignition cylinder. White 7
B-CAN High Pink 4 Data Immobilizer control unit around ignition cylinder. White 7
B-CAN Low Blue 5 Data Immobilizer control unit around ignition cylinder. White 7
Parking Lights Gray 8 (-) Headlight switch. Black & White 12
F-CAN High White 6 Data OBDII. Black 16
F-CAN Low Red or Black 14 Data OBDII. Black 16
Wire Information Connector Information
Rev.: 20 727170
Platform: DBALL2
Firmware HONDA56:
© 2017 Directed. All rights reserved.
Type 1 - Vehicle Wiring Reference ChartPage 5
Function Color Pin Polarity Location Color Pins
Honda Accord Crosstour 2010-2012
12V White 1 (+) Ignition switch. White 5
Starter Yellow 2 (+) Ignition switch. White 5
Ignition Blue 3 (+) Ignition switch. White 5
Accessory Orange 5 (+) Ignition switch. White 5
Immobilizer Data Lt. Green 2 Data Immobilizer control unit around ignition cylinder. Black 7
Immobilizer Ignition Interrupt Yellow 6 (+) Immobilizer control unit around ignition cylinder. Black 7
B-CAN High Pink 4 Data Immobilizer control unit around ignition cylinder. Black 7
B-CAN Low Blue 5 Data Immobilizer control unit around ignition cylinder. Black 7
Parking Lights Gray 8 (-) Headlight switch. Black & White 12
F-CAN High White 6 Data OBDII. Black 16
F-CAN Low Red or Black 14 Data OBDII. Black 16
Honda Odyssey 2011-2017
12V White 1 (+) Ignition switch. White 5
Starter Yellow 2 (+) Ignition switch. White 5
Ignition Blue 3 (+) Ignition switch. White 5
Accessory Orange 5 (+) Ignition switch. White 5
Immobilizer Data Violet 2 Data Immobilizer control unit around ignition cylinder. White 7
Immobilizer Ignition Interrupt Yellow 6 (+) Immobilizer control unit around ignition cylinder. White 7
B-CAN High Pink 4 Data Immobilizer control unit around ignition cylinder. White 7
B-CAN Low Blue 5 Data Immobilizer control unit around ignition cylinder. White 7
Parking Lights Gray 8 (-) Headlight switch. Black & White 12
F-CAN High White 6 Data OBDII. Gray or White 16
F-CAN Low Black 14 Data OBDII. Gray or White 16
Honda Pilot 2009-2015
12V White 1 (+) Ignition switch. White 5
Starter Yellow 2 (+) Ignition switch. White 5
Ignition Pink 3 (+) Ignition switch. White 5
Accessory Orange 5 (+) Ignition switch. White 5
Immobilizer Data Pink 2 Data Immobilizer control unit around ignition cylinder. Green 7
Immobilizer Ignition Interrupt Brown 6 (+) Immobilizer control unit around ignition cylinder. Green 7
B-CAN High White 4 Data Immobilizer control unit around ignition cylinder. Green 7
B-CAN Low Lt. Green 5 Data Immobilizer control unit around ignition cylinder. Green 7
Parking Lights Gray 8 (-) Headlight switch. Black & White 12
F-CAN High White 6 Data OBDII. Black 16
F-CAN Low Red or Black 14 Data OBDII. Black 16
Wire Information Connector Information
1 8
169
F- Low p 4CAN : in 1White,
DiagnosticConnector OBDII(connector side view)
F- High p 6CAN : inBlack,
Not required in D2D mode.
21
27
4
21
27
21
19
18
17
20
22
23
24
25
26
28
29
30
31
32
12
35
67
89
10
11
12
13
14
15
16
4
HS CAN : 3High Tan/Black:
HS CAN : 4Low Tan:
(-) Parking Light Output
[1] ( ) Tach InputAC
(-) Trunk Status Input
(-) Door Status Input
Rem
ote
Sta
rter
(-) (Status)GWR
(-) OutputLock
(-) OutputUnlock
(-) Trunk Output
(+) 12V(-) Ground
1: (-) Lock InputGreen:
2: (-) Unlock InputBlue:
3: (-) Trunk InputRed/White:
10: (-) (Status) InputBlue/White: GWR
[1] ( ) Tach OutputAC : 5Violet/White:
(-) Door Status Output: 3Green/White:
(-) Push-to-Start Output: 2Green/Black:
(-) Trunk Status Output: 4Red/Black:
(+) 12V: 13Red:(+) 12V
(-) Ground: 14Black:(-) Ground
(+) Brake Status Output: 6Gray:
Immobilizer Data: 11Orange/Black:
(-) Hood Status Output: 12Blue/Red:
(+) Brake Input
(-) Hood Status Input
(+) Starter(+) Ignition 1
(+) Ignition 2
(+) Accessory
11
(+) Ignition 1: , pin 4Blue
12V (+): , pin 1White
(+) Ignition 2: , pin 3Red
(+) y: , pin 1Accessor Orange1
2
3
4
1
3
4
17
23
71
6B- High: , pin 16CAN Pink
B- Low: , pin 17CAN Blue
35
34
25
12
34
68
91
01
11
21
31
41
51
8
19
20
21
22
23
24
26
27
28
29
30
31
32
33
36
17
16
7
23
5
Immo. Data:Lt. Green,pin 21
WARNINGNo takeover feature is available. The engine will stop when a door is open . To remote start the engine, all doors must be closed.ed
(-) : , pinPTS Lt Blu. e 7
(+) : , pin 10Starter Lt. Green
(-) E-Brake Status Input
(-) : 10E-Brake Status Output Yellow/Black:
FT CAN High: 5Orange/Green:
FT CAN Low: 6Orange/Brown:
Headlight Switch(White & Black conn.
at headlight)
(-) Parking Lights:pin 8
6 5 4 3 2 1
712 10 9 811
Keyless AccessControl Unit(Gray connectorleft of column)
Power Control Unit(Lt. Blue connector
left of column)Power Control Unit(White connectors rightof fuse box)
[3] Ignition Interrupt (conn. side) 8: Yellow:
[3] Ignition Interrupt (veh. side) 9: Orange/Yellow:
CUT
[3]
Ignition:pin 17
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
With the exception of the Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII
[ ]2 Connect the Autolight wire only if the vehicle is equipped with automatic headlights.OFF
10
2DBALL
RF
Prog. Button
LED
4
14
12
2
P#: 2D65XKDTX
(-) Ground
RX
(+)12V
Installation Type 2Page 6
[3] Optional but required for OEM Remote Keyless Entry to operate when vehicle is remote started.
[2](-) Factory Alarm Rearm
[2](-) Autolights:pin 9
Rev.: 20 727170
Platform: DBALL2
Firmware HONDA56:
© 2017 Directed. All rights reserved.
Rev.: 20 727170
Platform: DBALL2
Firmware HONDA56:
© 2017 Directed. All rights reserved.
Type 2 - Vehicle Wiring Reference Chart
Locating Component
Page 7
D
Under left-side of dash
Fu
RB
se
/e
lay
ox
A
B
Key
less
Access
Unit
Power Control
Unit
F
E
Function Color Pin Polarity Location Color Pins
Acura TL (Smart Key) 2009-2013
12V White 1 (+) PCU (Power Control Unit), right of driver dash fuse box, bottom connector. White 1
Ignition 1 Blue 4 (+) PCU, right of driver dash fuse box, bottom connector. White 4
Ignition 2 Red 3 (+) PCU, right of driver dash fuse box, bottom connector. White 4
Accessory Orange 1 (+) PCU, right of driver dash fuse box, bottom connector. White 4
Parking Lights Gray 8 (-) Headlight switch. Black & White 12
Autolights Pink 9 (-) Headlight switch. Black & White 12
F-CAN High White 6 Data OBDII. Gray 16
F-CAN Low Black 14 Data OBDII. Gray 16
Immobilizer Data Lt. Green 21 Data Keyless Access Control Unit right of driver dash fuse box left of PCU, bottom connector. Gray 32
Immobilizer Ignition Interrupt Yellow 17 Data Keyless Access Control Unit right of driver dash fuse box left of PCU, bottom connector. Gray 32
PTS Lt. Blue 7 (-) PCU, right of driver dash fuse box, bottom connector. Lt. Blue 36
Starter Lt. Green 10 (+) PCU, right of driver dash fuse box, bottom connector. Lt. Blue 36
B-CAN High Pink 16 Data PCU, right of driver dash fuse box, bottom connector. Lt. Blue 36
B-CAN Low Blue 17 Data PCU, right of driver dash fuse box, bottom connector. Lt. Blue 36
Wire Information Connector Information
HS CAN : 3High Tan/Black:
HS CAN : 4Low Tan:
(-) Parking Light Output
[1] ( ) Tach InputAC
(-) Trunk Status Input
(-) Door Status Input
Rem
ote
Sta
rter
(-) (Status)GWR
(-) OutputLock
(-) OutputUnlock
(-) Trunk Output
1: (-) Lock InputGreen:
2: (-) Unlock InputBlue:
3: (-) Trunk InputRed/White:
10: (-) (Status) InputBlue/White: GWR
[1] ( ) Tach Output: 5AC Violet/White:
(-) Door Status Output: 3Green/White:
(-) Trunk Status Output: 4Red/Black:
(-) Ground
(+) 12V: 13Red:(+) 12V
(-) Ground: 14Black:(-) Ground
(+) Brake Status Output: 6Gray:
(-) Hood Status Output: 12Blue/Red:
(+) Brake Input
(-) Hood Status Input
(+) Starter
17
23
71
6(+) Starter:Lt Green. ,pin 10
35
34
25
12
34
56
89
10
11
12
13
14
15
18
19
20
21
22
23
24
26
27
28
29
30
31
32
33
36
17
16
7
23
Immo. Data:.Lt Green, pin 10
Junction Connector(White connector passenger kick panel)
Immobilizer Data: 11Orange/Black:
Not required in D2D mode.
(-) Push-to-Start Output: 2Green/Black:
2714 13 12 11 10 9 8 7 6 5 4 3
26 25 24 23 22 21 20 19 18 17 16 1528 2 1
(-) : , pinPTS Violet 7
B- High: , pin 16CAN Pink
B- Low: , pin 17CAN Blue
(-) E-Brake Status Input
(-) : 10E-Brake Status Output Yellow/Black:
1 8
169
F- LowCAN :p 4Black, in 1
F- HighCAN :White, p 6in
FT CAN High: 5Orange/Green:
FT CAN : 6Low Orange/Brown:
DiagnosticConnector OBDII(connector side view)
WARNINGNo takeover feature is available. The engine will stop when a door is open . To remote start the engine, all doors must be closed.ed
Headlight Switch(White & Black conn.
at headlight)
(-) Parking Lights:pin 8
6 5 4 3 2 1
712 10 9 811(+) 12V
(+) Ignition 1
(+) Ignition 2
(+) Accessory
11
(+) Ignition 1: , pin 4Blue
12V (+): , pin 1White
(+) Ignition 2: , pin 3Red
(+) y: , pin 1Accessor Orange1
2
3
4
1
3
4
Power Control Unit(Green & White connectorsright of column)
Power Control Unit(Lt. Blue connector
right of column)
(-) Ground
Installation Type 3
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
With the exception of the Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII
10
2DBALLRF
Prog. Button
LED
4
14
12
2
P#: 2D65XKDTX
RX
(+)12V
[ ]2 Connect the Autolight wire only if the vehicle is equipped with automatic headlights.OFF
Page 8
[2](-) Factory Alarm Rearm
[2](-) Autolights:pin 9
Rev.: 20 727170
Platform: DBALL2
Firmware HONDA56:
© 2017 Directed. All rights reserved.
Rev.: 20 727170
Platform: DBALL2
Firmware HONDA56:
© 2017 Directed. All rights reserved.
Type 3 - Vehicle Wiring Reference ChartPage 9
Power ControlUnit
Fuse BoxCombinationLight Switch
D
A
B
C
F
Locating Component
Function Color Pin Polarity Location Color Pins
Acura ZDX (Smart Key) 2010-2013
12V White 1 (+) PCU (Power Control Unit), right steering column, bottom connectoGreen 1
Ignition 1 Blue 4 (+) PCU, right steering column, bottom connector. White 4
Ignition 2 Red 3 (+) PCU, right steering column, bottom connector. White 4
Accessory Orange 1 (+) PCU, right steering column, bottom connector. White 4
Parking Light White 8 (-) Headlight switch. Black 12
Autolights Pink 9 (-) Headlight switch. Black 12
F-CAN High White 6 Data OBDII. White 16
F-CAN Low Black 14 Data OBDII. White 16
Immobilizer Data Lt. Green 10 Data Junction connector above passenger kick panel fuse box. White 28
PTS Violet 7 (-) PCU, right steering column. Lt. Blue 36
Starter Lt. Green 10 (+) PCU, right steering column. Lt. Blue 36
B-CAN High Pink 16 Data PCU, right steering column. Lt. Blue 36
B-CAN Low Blue 17 Data PCU, right steering column. Lt. Blue 36
Wire Information Connector Information
7
1
9
3
10
4
11
5
12
6
8
2
5 4 3
12
[1] ( ) Tach InputAC
(+) Brake Input
(-) Trunk Status Input
(-) Door Status Input
Rem
ote
Sta
rter
(-) Parking Lights
(+) Ignition: , pin 2Blue
(+) Starter:Yellow, pin 5
Acc. 1:Orange,
pin 4
(+) Acc. 2:Red, pin 3
(+) 12V: , pin 1White
(-) Hood Status Input
Ignition Switch( connector at ignition)White
Headlight Switch(White connector
at headlight)
(-) Parking Lights:, pin 8Gray
Not required in D2D mode.
1: (-) Lock InputGreen:
2: (-) Unlock InputBlue:
3: (-) Trunk InputRed/White:
10: (-) (Status) InputBlue/White: GWR
(-) (Status)GWR
(-) OutputLock
(-) OutputUnlock
(-) Trunk Output
(+) Ignition
(+) Starter
(+) Accessory 2
(+) Accessory 1
(+) 12V
(-) Ground
(+) 12V (+) 12V: 13Red:
(-) Ground (-) Ground: 14Black:
[1] ( ) Tach OutputAC : 5Violet/White:
(+) Brake Status Output: 6Gray:
(-) Door Status Output: 3Green/White:
(-) Trunk Status Output: 4Red/Black:
Immobilizer Data: 11Orange/Black:
(-) Hood Status Output: 12Blue/Red:
HS CAN : 3High Tan/Black:
HS CAN : 4Low Tan:
(-) E-Brake Status Input
(-) : 10E-Brake Status Output Yellow/Black:
1 8
169
F- Low p 4CAN : in 1Red,
DiagnosticConnector
BDIIO
F- High p 6CAN : inWhite,
FT CAN High: 5Orange/Green:
FT CAN : 6Low Orange/Brown:
Immo. Data:pin 2
[3] Ignition:pin 6
14 3 57 256
B- High: pin 4CAN
B- Low: pin 3CAN
Immobilizer Control Unit(Black conn. around ignition cylinder)
CUT
[3] Ignition Interrupt (conn. side) 8: Yellow:
[3] Ignition Interrupt (veh. side) 9: Orange/Yellow:
Installation Type 4
10
2DBALL
RF
Prog. Button
LED
4
14
12
2
P#: 2D65XKDTX
(-) Ground
RX
(+)12V
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
With the exception of the Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII
[2] Connect the Rearm wire if the vehicle is equipped with automatic headlights.only
Page 01
[3] Optional but required for OEM Remote Keyless Entry to operate when vehicle is remote started.
[2](-) Factory Alarm Rearm
[2](-) Autolights:pin 1
Rev.: 20 727170
Platform: DBALL2
Firmware HONDA56:
© 2017 Directed. All rights reserved.
Rev.: 20 727170
Platform: DBALL2
Firmware HONDA56:
© 2017 Directed. All rights reserved.
Type - Vehicle Wiring Reference Chart4Page 11
Function Color Pin Polarity Location Color Pins
Honda Civic 2012-2015
12V White 1 (+) Ignition Switch. White 5
Ignition Blue 2 (+) Ignition Switch. White 5
Starter Yellow 5 (+) Ignition Switch. White 5
Accessory 2 Red 3 (+) Ignition Switch. White 5
Accessory 1 Orange 4 (+) Ignition Switch. White 5
Immobilizer Data Lt. Green 2 Data Immobilizer connector, at steering column around ignition cylinder. Gray 7
Immobilizer Ignition Interrupt Yellow 6 (+) Immobilizer control unit around ignition cylinder. Gray 7
B-CAN High Pink 4 Data Immobilizer connector, at steering column around ignition cylinder. Gray 7
B-CAN Low Blue 5 Data Immobilizer connector, at steering column around ignition cylinder. Gray 7
Parking Lights Gray 8 (-) Headlight switch. White 12
Autolights Orange 1 (-) Headlight switch. White 12
F-CAN High White 6 Data OBDII. Gray or White 16
F-CAN Low Red 14 Data OBDII. Gray or White 16
Lock Blue 11 (-) Door Lock, driver door harness - located in upper driver kick panel. Blue 24
Unlock Gray 18 (-) Door Lock, driver door harness - located in upper driver kick panel. Blue 24
Wire Information Connector Information
7
1
9
3
10
4
11
5
12
6
8
25 4 3
12
[1] ( ) Tach InputAC
(+) Brake Input
(-) Trunk Status Input
(-) Door Status Input
Rem
ote
Sta
rter
(-) (Status)GWR
(-) OutputLock
(-) OutputUnlock
(-) Trunk Output
(+) Ignition
(+) Starter
(+) Accessory 2
(+) Accessory 1
(-) Parking Lights(+) 12V
(-) Ground
(+) Ignition: , pin 2Red
(+) Starter:, pin 5Green
Blue, pin 4 (+) Acc. 2:, pin 3Yellow
(-) Hood Status Input
1: (-) Lock InputGreen:
2: (-) Unlock InputBlue:
3: (-) Trunk InputRed/White:
10: (-) (Status) InputBlue/White: GWR
[1] ( ) Tach OutputAC : 5Violet/White:
(+) Brake Status Output: 6Gray:
(-) Door Status Output: 3Green/White:
(-) Trunk Status Output: 4Red/Black:
Immobilizer Data: 11Orange/Black:(-) Hood Status Output: 12Blue/Red:
Ignition Switch(White connector at ignition)
Headlight Switch(White connector at headlights)
(-) Parking Light: , pin 8Blue
Not required in D2D mode.
(-) E-Brake Status Input
(+) 12V: , pin 1White
(-) : 10E-Brake Status Output Yellow/Black:
(+) 12V (+) 12V: 13Red:
(-) Ground (-) Ground: 14Black:
HS CAN : 3High Tan/Black:
HS CAN : 4Low Tan:
B- High: , pin 4CAN Pink
B- Low: , pin 5CAN Blue
1 8
169
F- LowCAN :in 1Red, p 4
DiagnosticConn.
BDIIO
F- High p 6CAN : inWhite,
FT CAN High: 5Orange/Green:
FT CAN : 6Low Orange/Brown:
Immo. Data:Yellow, pin 2
[3] Ignition:pin 6
14 3 57 256
Immobilizer Control Unit(Black conn. around ignition cylinder)
CUT
[3] Ignition Interrupt (conn. side) 8: Yellow:
[3] Ignition Interrupt (veh. side) 9: Orange/Yellow:
(-) Ground
P#: 2D65XKDTX
RX
(+)12V
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
With the exception of the Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII
[2] Connect the Autolight wire only if the vehicle is equipped with automatic headlights.OFF
Installation Type 5
10
2DBALL
RF
Prog. Button
LED
4
12
21
4
Page 21
[3] Optional but required for OEM Remote Keyless Entry to operate when vehicle is remote started.
[2](-) Factory Alarm Rearm
[2](-) Autolights:pin 1
Rev.: 20 727170
Platform: DBALL2
Firmware HONDA56:
© 2017 Directed. All rights reserved.
Rev.: 20 727170
Platform: DBALL2
Firmware HONDA56:
© 2017 Directed. All rights reserved.
Type - Vehicle Wiring Reference Chart5Page 31
Function Color Pin Polarity Location Color Pins
Honda CR-V 2012-2016
12V White 1 (+) Ignition Switch. White 5
Ignition Red 2 (+) Ignition Switch. White 5
Starter Green 5 (+) Ignition Switch. White 5
Accessory 2 Yellow 3 (+) Ignition Switch. White 5
Accessory 1 Blue 4 (+) Ignition Switch. White 5
Immobilizer Data Yellow 2 Data Immobilizer connector at steering column around ignition cylinder. Black 7
Immobilizer Ignition Interrupt Blue 6 (+) Immobilizer control unit around ignition cylinder. Black 7
B-CAN High Pink 4 Data Immobilizer connector at steering column around ignition cylinder. Black 7
B-CAN Low Blue 5 Data Immobilizer connector at steering column around ignition cylinder. Black 7
Parking Light Blue 8 (-) Headlight switch. White 12
Autolights Tan 1 (-) Headlight switch. White 12
F-CAN High White 6 Data OBDII. Gray 16
F-CAN Low Red 14 Data OBDII. Gray 16
Unlock Gray 14 (-) Door Lock, driver door harness. White 18
Lock Green 17 (-) Door Lock, driver door harness. White 18
Wire Information Connector Information
(-) Parking Output
[2](-) Factory Alarm Rearm
Headlight Switch(White or Blue conn.left of steering column)
[1] ( ) Tach InputAC
(-) Trunk Status Input
(-) Door Status Input
(-) (Status)GWR
(-) OutputLock
(-) OutputUnlock
(-) Trunk Output
(+) 12V
(+) Brake Input
(-) Hood Status Input
(+) Starter
(+) Ignition 1
(+) Ignition 2
(+) Accessory
11(+) 12V: , pin 1White
1
3
3
4
4
2
1
17
23
7 16
353425
1 2 3 4 5 6 8 9 10 11 12 13 14 15 18
19 20 21 22 23 24 26 27 28 29 30 31 32 33 36
17167
23
Not required in D2D mode.
HS CAN : 3High Tan/Black:
HS CAN : 4Low Tan:
(+) 12V: 13Red:(+) 12V
(-) Ground: 14Black:(-) Ground
1: (-) Lock InputGreen:
2: (-) Unlock InputBlue:
3: (-) Trunk InputRed/White:
10: (-) (Status) InputBlue/White: GWR
[1] ( ) Tach Output: 5AC Violet/White:
(-) Door Status Output: 3Green/White:
(-) Trunk Status Output: 4Red/Black:
(+) Brake Status Output: 6Gray:
(-) Hood Status Output: 12Blue/Red:
Immobilizer Data: 11Orange/Black:
(-) Push-to-Start Output: 2Green/Black:
(-) E-Brake Status Input
(-) Parking Light:, pin 8Gray
[2](-) Autolights:, pin 1Orange
(+) Ignition 1: , pin 1Blue
(+) Ignition 2: , pin 2Green
(+) y: , pin 4Accessor Orange
(+) Starter:pin 10
(-) : pinPTS 7
B-CAN High: , pinPink 16
(-) : 10E-Brake Status Output Yellow/Black:
17
23456121110 9 8
Rem
ote
Sta
rter
FT CAN High: 5Orange/Green:
FT CAN : 6Low Orange/Brown:
1 8
169
F- LowCAN :in 1Red, p 4
DiagnosticConnector OBDII(connector side view)
F- HighCAN :White, p 6in
WARNINGNo takeover feature is available. The engine will stop when a door is open . To remote start the engine, all doors must be closed.ed
(-) Ground
Power Control Unit(Green 1-pin & White 4-pinconnectors behind clusteror left of column)
Power Control Unit(Lt. Blue connectorbehind cluster orleft of column)
21
27
4
21
27
21
19
18
17
20
22
23
24
25
26
28
29
30
31
32
12
35
67
89
10
11
12
13
14
15
16
4
Immo. Data:Lt. Green,pin 21
Keyless AccessControl Unit(Gray connectorleft of column)
[3] Ignition Interrupt (conn. side) 8: Yellow:
[3] Ignition Interrupt (veh. side) 9: Orange/Yellow:
CUT
[3]
Ignition:pin 17
B-CAN : , pinLow 17Blue
10
RF
LED
4
14
12
2
P#: 2D65XKDTX
(-) Ground
RX
(+)12V
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
With the exception of the Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII
[ ]2 Connect the Autolight wire only if the vehicle is equipped with automatic headlights.OFF
Installation Type 6
2DBALLProg. Button
Page 41
[3] Optional but required for OEM Remote Keyless Entry to operate when vehicle is remote started.
Rev.: 20 727170
Platform: DBALL2
Firmware HONDA56:
© 2017 Directed. All rights reserved.
Rev.: 20 727170
Platform: DBALL2
Firmware HONDA56:
© 2017 Directed. All rights reserved.
Type - Vehicle Wiring Reference Chart6Page 51
A
B
Key
less
Access
Unit
Power Control
Unit
F
E
On the , the is to theILX Keyless Access Control Unitright of the steering column, and the Power Control Unitis behind the instrument cluster.
On the , the and theRDX Keyless Access Control UnitPower Control Unit are both to the right of the steeringcolumn.
Locating Component
Function Color Pin Polarity Location Color Pins
Acura ILX (Smart Key) 2013-2015
12V White 1 (+) PCU (Power Control Unit), behind cluster. Green 1
Ignition 1 Blue 1 (+) PCU, behind cluster. White 4
Ignition 2 Green 2 (+) PCU, behind cluster. White 4
Accessory Orange 4 (+) PCU, behind cluster. White 4
Parking Light Gray 8 (-) Headlight Switch White 12
Autolights Orange 1 (-0 Headlight Switch Blue 12
F-CAN High White 6 Data OBDII. White or Gray 16
F-CAN Low Red 14 Data OBDII. White or Gray 16
Immobilizer Data Lt Green 21 Data Keyless Access Control Unit right side of steering column. Gray 32
Immobilizer Ignition Interrupt Yellow 17 Data Keyless Access Control Unit right side of steering column. Gray 32
PTS Brown or Gray 7 (-) PCU, behind cluster. Lt. Blue 36
Starter Yellow or Orange 10 (+) PCU, behind cluster. Lt. Blue 36
B-CAN High Pink 16 Data PCU, behind cluster. Lt. Blue 36
B-CAN Low Blue 17 Data PCU, behind cluster. Lt. Blue 36
Acura RDX (Smart Key) 2013-2015
12V White 1 (+) PCU (Power Control Unit), right side of steering column. Green 1
Ignition 1 Blue 1 (+) PCU, right side of steering column. White 4
Ignition 2 Red 2 (+) PCU, right side of steering column. White 4
Accessory Orange 4 (+) PCU, right side of steering column. White 4
Parking Light Gray 8 (-) Headlight Switch Blue 12
Autolights Orange 1 (-0 Headlight Switch Blue 12
F-CAN High White 6 Data OBDII. White or Gray 16
F-CAN Low Red 14 Data OBDII. White or Gray 16
Immobilizer Data Lt Green 21 Data Keyless Access Control Unit right side of steering column. Gray 32
Immobilizer Ignition Interrupt Yellow 17 Data Keyless Access Control Unit right side of steering column. Gray 32
PTS Brown 7 (-) PCU, right side of steering column. Lt. Blue 36
Starter Gray 10 (+) PCU, right side of steering column. Lt. Blue 36
B-CAN High Pink 16 Data PCU, right side of steering column. Lt. Blue 36
B-CAN Low Blue 17 Data PCU, right side of steering column. Lt. Blue 36
Wire Information Connector Information
Module Programming for Types 1, ,4 5Page 16
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check toensure everything is correct prior to moving onto the next step.
Warning! To take advantage of advanced features, you must use Xpress 4.5 (and higher) or the Directechs Mobile app.VIP
When the flashing operation is successful, you can proceed with the programming instructions below.
Refer to the Diagnostics section on page for more information and for troubleshooting purposes.LED s 25-26
OR
If required for your installation, connect the 10-pin, 12-pin and 14-pin harnesses tothe module, then connect the 4-pin D2D harness.
D2D Installation
W W Installation2
If required for your installation, connect the 10-pin and 12-pin harnesses to themodule, then connect the 14-pin harness to the module.
10-pinD2D
1st
12-pin14-pin
2nd
3rd
10-pinD2D
1st
4th
12-pin14-pin
2nd
3rd
Flashing a module using your computer:
1. Connect the interface module to your computer using theXKLoader2.
2. Go to www.directechs.com using Internet Explorer, andselect the button.Flash Module
3. Follow the instructions to select your vehicle, installationtype, and configure your options.
4. Once you have configured the firmware options, click on theFLASH button.
Flashing a module using your smartphone or tablet
1. Connect the interface module to your oader3.XKL
2. Launch the Directechs Mobile app on your smartphone ortablet.
3. Select and follow the on screenFLASH YOUR MODULEinstructions.
2
4
3 The turns green for 3 seconds then shuts off.LED ON
Turn the key to the ignition position.
Turn vehicle ignition off once the module is successfully programmed.
Key IN OF
FSTART
IGN
Key OUT OF
F
START
IGN
&OffSolid Green x3 sec
1Solid
Wait until the LED turns solid red.ON
Rev.: 20 727170
Platform: DBALL2
Firmware HONDA56:
© 2017 Directed. All rights reserved.
Module Programming for Types 2 & 3 (Takeover feature is Unavailable)Page 17
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check toensure everything is correct prior to moving onto the next step.
Warning! To take advantage of advanced features, you must use Xpress 4.5 (and higher) or the Directechs Mobile app.VIP
When the flashing operation is successful, you can proceed with the programming instructions below.
Refer to the Diagnostics section on page for more information and for troubleshooting purposes.LED s 25-26
OR
If required for your installation, connect the 10-pin, 12-pin and 14-pin harnesses tothe module, then connect the 4-pin D2D harness.
D2D Installation
W W Installation2
If required for your installation, connect the 10-pin and 12-pin harnesses to themodule, then connect the 14-pin harness to the module.
10-pinD2D
1st
12-pin14-pin
2nd
3rd
10-pinD2D
1st
4th
12-pin14-pin
2nd
3rd
1Solid
Flashing a module using your computer:
1. Connect the interface module to your computer using theXKLoader2.
2. Go to www.directechs.com using Internet Explorer, andselect the button.Flash Module
3. Follow the instructions to select your vehicle, installationtype, and configure your options.
4. Once you have configured the firmware options, click on theFLASH button.
Flashing a module using your smartphone or tablet
1. Connect the interface module to your oader3.XKL
2. Launch the Directechs Mobile app on your smartphone ortablet.
3. Select and follow the on screenFLASH YOUR MODULEinstructions.
2 Insert the remote into the key port.OEM KEY PORTENGINESTARTSTOP
&OffSolid Green x3 sec
3
4
5
The turns solid green for 3 seconds and shuts off.LED ON
1XENGINESTARTSTOP
PUSH
2X
Press the Push-to-Start ( ) button more to turn the ignition .PTS OFFonce
Press the Push-to-Start ( ) button to turn the ignition .PTS ONtwice
Important: Do press the brake pedal.NOTENGINESTARTSTOP
PUSHDo NOT
press the
brake pedal
Wait until the LED turns solid red.ON
Rev.: 20 727170
Platform: DBALL2
Firmware HONDA56:
© 2017 Directed. All rights reserved.
Module Programming for Type 6Page 18
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check toensure everything is correct prior to moving onto the next step.
Warning! To take advantage of advanced features, you must use Xpress 4.5 (and higher) or the Directechs Mobile app.VIP
When the flashing operation is successful, you can proceed with the programming instructions below.
Refer to the Diagnostics section on page 1 for more information and for troubleshooting purposes.LED s 2
OR
If required for your installation, connect the 10-pin, 12-pin and 14-pin harnesses tothe module, then connect the 4-pin D2D harness.
D2D Installation
W W Installation2
If required for your installation, connect the 10-pin and 12-pin harnesses to themodule, then connect the 14-pin harness to the module.
10-pinD2D
1st
12-pin14-pin
2nd
3rd
10-pinD2D
1st
4th
12-pin14-pin
2nd
3rd
1Solid
Flashing a module using your computer:
1. Connect the interface module to your computer using theXKLoader2.
2. Go to www.directechs.com using Internet Explorer, andselect the button.Flash Module
3. Follow the instructions to select your vehicle, installationtype, and configure your options.
4. Once you have configured the firmware options, click on theFLASH button.
Flashing a module using your smartphone or tablet
1. Connect the interface module to your oader3.XKL
2. Launch the Directechs Mobile app on your smartphone ortablet.
3. Select and follow the on screenFLASH YOUR MODULEinstructions.
4
3 2XENGINESTARTSTOP
PUSHPlace key next to Push-to-Start ( ) button andPTSpress to turn ignitionthis button the .twice ON
Important: Do press the brake pedal.NOT
&OffSolid Green x3 sec
The turns green for 3 seconds and shuts off.LED ON
Do NOT
press the
brake pedal
2 D the key the .isassemble to remove batteryOEM FOB
5 1XPress once on the Push-to-Start (PTS) button to turn vehicleignition off once the module is successfully programmed.
ENGINESTARTSTOP
PUSH
Rev.: 20 8160 10
Platform: DBALL/DBALL2
Firmware: HONDA56
Wait until the LED turns solid red.ON
REMOVEBATTERY
Rev.: 20 727170
Platform: DBALL2
Firmware HONDA56:
© 2017 Directed. All rights reserved.
2
Solid
&
Solid Flashes
&
Release
3
Wait 3 seconds until the orange aitLED turns solid , and w 10 more secondsONuntil the andLED starts to flash orange red.
Release the programming button. The turns solid red.LED ON
Warning gainst xecuting a Hard Reset!A EA hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (suchas and D2D options) may have to be reconfigured. See the section of this guide.RFTD Feature & Option List
1 OR
If required for your installation, c , &onnect the 10-pin 12-pin14-pin harnesses to the module Press hold the. andp , then connect the 4-pin D2D harness.rogramming button
D2D Installation
If required for your installation, connect the 10-pin & 12-pinharnesses to the module Press hold the rogramming. and pbutton, then connect the 14-pin harness to the module.
W2W Installation
10-pinD2D
1st
12-pin14-pin
2nd
4th
3rd
10-pinD2D
1st
5th
12-pin14-pin
2nd
3rd
4th
Module Reset
Hard Reset
2 & &Solid SolidRelease
Wait 3 seconds until the orange then release theLED turns solidONp The then turns solid red.rogramming button. LED ON
A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashedto the module using the web config tool will not be affected.
Page 19
1 OR
If required for your installation, c , &onnect the 10-pin 12-pin14-pin harnesses to the module Press hold the. andp , then connect the 4-pin D2D harness.rogramming button
D2D Installation
If required for your installation, connect the 10-pin & 12-pinharnesses to the module Press hold the rogramming. and pbutton, then connect the 14-pin harness to the module.
W2W Installation
10-pinD2D
1st
12-pin14-pin
2nd
4th
3rd
10-pinD2D
1st
5th
12-pin14-pin
2nd
3rd
4th
Rev.: 20 727170
Platform: DBALL2
Firmware HONDA56:
© 2017 Directed. All rights reserved.
Page 20
Feature & Option List
It is recommended to configure all features and options listed below thethe using configuration tool found on the moduleflashing page on www.directechs.com. The web offers more options; however, manual configuration of the features ispossible using the information on this page.
* Default Option
Feat. Operation Flashes / Option Description
1. No RF Output* Module is connected to a remote starter using a standard installation.
2. RFTD Output Module is connected to an XL202 using an RSR or RXT installation (when available).
3. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available).
1. Driver Priority* Unlocks only the driver door on first press and unlocks all doors on a second press within 5 seconds.
2. All Unlocks all doors on first press.
1. DisabledThe OEM alarm will not be controlled by DBALL upon remote start. No disarm or arm command will be
executed at the beginning or end of the sequence; it must be controlled by the Remote Starter.
2. SafelockSmart OEM Alarm Control will behave like a standard Safelock feature on a remote starter. It will unlock at
the beginning of the sequence, and relock after start and shutdown.
3. Enabled*
Smart OEM Alarm Control will synchronize with the OEM alarm so that it will disarm and rearm the vehicle in
the remote start sequence, only when required. The reason for this is, factory alarm control must often be
done by lock or unlock operation. This could create unnecessary actions on door lock modules, such as the
horn to honk. When possible, Smart OEM Alarm Control will monitor the alarm and door lock status to detect
if the disarm or rearm is required. If the vehicle is unlocked or is not equipped with factory alarm, the
disarm/rearm will not be executed. Smart OEM Alarm Control will also monitor the remote starter actions so
that the factory alarm control is not done twice. A remote starter, for which the Safelock feature is active, will
work perfectly with this option and will make it invisible to the user.
3Smart OEM
Alarm Control
1RFTD Output
Type
2Unlock Driver
Priority
To enter feature programming routine- Turn t , thenhe ignition .ON OFF- Within 5 seconds, press and the rogramming button turns after 3 seconds . Release theHOLD LED ONp until the orange ( )
Programming button.- The to indicate the feature number is 1. After a short delay, the flashes rapidly to indicateLED LEDwill flash green once slowly red
the current option of feature 1 . repeat(i.e. 1x green followed by 1x red indicates feature 1 is set to option 1) The flashing sequence willuntil .a new command is entered
Changing feature options- Press the arm or disarm button on aftermarket transmitter to change the option of the selected feature.lock/ unlock/- The flashes rapidly the number of times equal to the current option number. After a short delay, the flashes green slowlyLED LEDred
the number of times to indicate the current feature. repeat until .The flashing sequence will a new command is entered
Accessing another feature- Press and release the programming button a number of times to advance from the current feature to the next desired feature.- The flashes green slowly the number of times equal to the feature number. After a short delay, the flashes red rapidly toLED LED
indicate the current option of the current feature. repeat until .The flashing sequence will a new command is entered
When the maximum number of features or options is reached, the will start flashing again from the first feature or option.LED
Once a feature is programmed- Other features can be programmed.- The feature programming can be exited.
Exiting feature programming- No activity for 30 seconds; after 30 seconds, the will turn orange for 2 seconds to confirm the end of the programmingLED ON
sequence.OR
- Press and the programming button for 3 seconds. After 3 seconds, the will turn orange for 2 seconds to confirm theHOLD LED ONend of the programming sequence.
Feature ProgrammingProgramming
Button
Rev.: 20 727170
Platform: DBALL2
Firmware HONDA56:
© 2017 Directed. All rights reserved.
Rev.: 20 727170
Platform: DBALL2
Firmware HONDA56:
© 2017 Directed. All rights reserved.
LED Description Troubleshooting
Module has no power.
Make sure the D2D harness is connected or that the 12
Volt is present between the red and black wires. If the
12 Volt is present, the module may be defective.
Waiting to begin the programming sequence.Ensure the correct programming procedure is being
followed.
Initialization failed.Reset the module and complete the programming again.
If the issue persists, please contact Technical Support.
Transponder functions were skipped.
(If compatible) when RXT mode is not desired or
convenience features are needed, please reset and
reprogram the module.
All required CAN networks has been detected. Normal operation.
1 of 2 CAN networks has been detected. Normal operation
Key2GO initiated.Please follow the steps indicated in “Module
programming” to complete the Key2GO programming.
Module was successfully programmed with all functions. Normal operation
Module was successfully programmed without
transponder functions.Normal operation.
CAN2 not detected.
Check the CAN2 Orange/Green and Orange/Brown wire
connections. Wake up the data bus by turning the
ignition on and try again. If your installation does not
require this connection, skip this step by pressing the
programming button 5 times.
J1850 not detected.Check the J1850 wire connection. Wake up the data bus
by turning the ignition on and try again.
CAN1 not detected.
Check the CAN1 Tan and Tan/Black wire connections.
Wake up the data bus by turning the ignition on and try
again. If your installation does not require this
connection, skip this step by pressing the programming
button 5 times.
Bypass data not detected.
Check the bypass line connection. If more than one wire
is used, make sure they are not inverted. Ensure the
vehicle still operates correctly using the factory key.
Bypass processing error.
The bypass calculation failed. Reset the module and try
again. If the condition persists, please contact Technical
Support.
ISO 1 not detected.
The Yellow/Black wire did not detect the expected
signal. Refer to "Installation (wiring diagrams & vehicle
wiring reference charts)" to check the connections.
ISO 2 not detected.
The Orange/Black wire did not detect the expected
signal. Refer to "Installation (wiring diagrams & vehicle
wiring reference charts)" to check the connections.
MUX not detected.
The Violet/Green or Violet/Brown wire did not detect the
expected voltage value. Refer to "Installation (wiring
diagrams & vehicle wiring reference charts)" to check
the connections.
Module Programming
Module Programming - Error Codes
Solid red
Flashes redx 1
Flashes redx 1
Flashes redx 2
Flashes redx 3
Flashes redx 4
Flashes redx 5
Flashes redx 6
Flashes redx 7
Solid greenx 3 secs
Flashesgreen
Solid orange
Flashes red& green
Off
Flashesorange
Flashesorangeslowly
Solid orangex 3 secs
LED Diagnostics & Troubleshooting
© 2016 Directed. All rights reserved.
Page 21
Rev.: 20 727170
Platform: DBALL2
Firmware HONDA56:
© 2017 Directed. All rights reserved.
LED Description Troubleshooting
OBDII feature is not supported.The diagnostic data bus was not detected, therefore the
SmartStart features will be limited.
Ground When Running (Status) command received. The module has initialized the remote start sequence.
Ignition ON command received.The module has received the Ignition ON command and
is processing the remote start sequence.
Start ON command received.The module has received the Start ON command and is
processing the remote start sequence.
PTS shutdown error.The PTS output from the module was not activated due
to safety protection.
CAN bus incorrectly detected.
Verify the CAN1 and CAN2 connections. Refer to
“Installation (wiring diagrams & vehicle wiring reference
charts)” to check the connections.
LOCK command received.
UNLOCK command received.
TRUNK command received.
AUX1 command received.
AUX2 command received.
AUX3 command received.
Takeover successful. Normal operation.
Runsafe was not disabled.No UNLOCK command was received prior to opening the
door, or the 45 second timer expired in takeover mode.
Brake was not detected.The brakes were not detected, which prevents the
system from shutting down the vehicle.
Smart key was not detected.The smart key was not detected, which prevents the
system from shutting down the vehicle.
Speed was detected.The vehicle was detected as moving, which prevents the
system from shutting it down.
External module synchronization
Commands
Activation Ground When Running (Status)
If the bypass module fails to flash, it did not receive the
signal. Commands can come from RF or D2D.
Shutdown codes
(Flashes red,red thenorange) x 10
Flashes red& orange
Flashes redx 21
Flashes redx 2
Flashes redx 4
Flashes redx 10
Flashes redx 1
Flashes redx 3
Flashesgreen
Flashesgreenquickly
Flashesgreen x 1
Flashesorange x 1
Flashesorange x 2
Flashesorange x 3
Flashesorange x 5
Flashesorange x 4
Flashesorange x 6
Page 22
For a period of from the date of purchase of a Directed Electronics remote start or security product, DirectedONE YEARElectronics. (“ ”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, theDIRECTEDsecurity or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or materialunder normal use, provided the following conditions are met: the Part was purchased from an authorized dealer;DIRECTEDand the Part is returned to , postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing theDIRECTEDfollowing information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and completeproduct and Part description.
This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to itsintended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation orother causes not arising out of defect in materials or construction.
TO THE MAXIMUM EXTENT ALLOWED BY LAW EXCEPT AS STATED ABOVE ALL WARRANTIES INCLUDING, , ,BUT NOT LIMITED TO EXPRESS WARRANTY IMPLIED WARRANTY WARRANTY OF MERCHANTABILITY, , ,FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUALPROPERTY ARE EXPRESSLY EXCLUDED AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY, ;PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY OBLIGATION OR LIABILITY IN CONNECTION WITH ITS,PRODUCTS DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALLACTS OF.THIRD PARTIES INCLUDING DEALERS OR INSTALLERS DIRECTED IS NOT OFFERING GUARANTEE OR. AINSURANCE AGAINST VANDALISM DAMAGE OR THEFT OF THE AUTOMOBILE ITS PARTS OR CONTENTS, , , ,AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER INCLUDING WITHOUT LIMITATION, ,LIABILITY FOR THEFT DAMAGE OR VANDALISM IN THE EVENT OF CLAIM OR DISPUTE INVOLVING, , . A ADIRECTED OR ITS SUBSIDIARY THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF,CALIFORNIA CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE.DISPUTE THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED.TO THE AUTHORIZED DIRECTED DEALER PURCHASE PRICE OF THE PART DIRECTED SHALL NOT BE’S .RESPONSIBLE FOR ANY DAMAGES WHATSOEVER INCLUDING BUT NOT LIMITED TO ANY CONSEQUENTIAL, ,DAMAGES INCIDENTAL DAMAGES DAMAGES FOR THE LOSS OF TIME LOSS OF EARNINGS COMMERCIAL, , , ,LOSS LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE NOTWITHSTANDING THE ABOVE THE, . ,MANUFACTURER DOES OFFER LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED OPTION THEA ’SPARTAS DESCRIBED ABOVE.
This warranty only covers Parts sold within the United States ofAmerica and Canada. Parts sold outside of the United States ofAmerica or Canada are sold “ - ” and shall have , express or implied. Some states do not allow limitationsAS IS NO WARRANTYon how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warrantygives you specific legal rights and you may also have other rights that vary from State to State. does not and hasDIRECTEDnot authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.For further details relating to warranty information of Directed products, please visit the support section of ’sDIRECTEDwebsite at: www.directed.com
920-10012-01 2013-07
This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the selectvehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. : Under noDISCLAIMERcircumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for anyconsequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, norwill they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / databus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of thisproduct be liable for consequential damages sustained in connection with this product and neither assumes nor authorizesany representative or other person to assume for it any obligation or liability other than the replacement of this product only.
Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1;7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent:2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; EuropeanPatent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.
Limited Consumer WarrantyOne YearPage 32
Rev.: 20 727170
Platform: DBALL2
Firmware HONDA56:
© 2017 Directed. All rights reserved.
Quick Reference Guide
Notes
Quick Reference GuideDBALL2-HONDA56
© 2017 Directed. All rights reserved.