www.kimray.comE3:20.5

Issued 6/18Current Revision:Update image

BALANCED MOTOR VALVES

PISTON BALANCED PRESSURE CLOSE

Stem and Seat AssemblyMotor Valve Diaphragm PressureUpstream PressureDownstream Pressure

Stem

Cage

Seat

OilPiston

APPLICATIONS: Pilot operated oil or water valve for separators, meters, and water knockouts where a reduced signal pressure is available, and where freezing occurs due to a higher pressure drop.

FEATURES: Piston balanced single seat 10 psig minimum diaphragm pressure Standard 303 stainless valve stem Reinforced oil resistant synthetic rubber diaphragms & seats Easy to service and repair Available for pressure opening or pressure closing service

CERTIFICATIONS: Canadian Registration Number (CRN): 0C15804.24567890NTY (Ductile) 0C15621.24567890NTY (Steel)

SUPPLY PRESSURE: 10 to 35 psig.

OPERATION TEMPERATURE: Standard - 225°F. Max. Heat Modified - 350°F. Max.

CAPACITY: Refer to Table of Contents.

Kimray is an ISO 9001- certified manufacturer.

Cf & Cv VALUESLine Size Trim Size Cf Cv

2" 1.50" 0.79 23.33" 2.25" 0.79 43.84" 3.00" 0.79 70.16" 4.88" 0.79 277.0

www.kimray.comE3:20.8

Issued 4/20Current Revision:Add lifting ring

BALANCED MOTOR VALVES

PISTON BALANCED PRESSURE CLOSESTEEL

ANGLE VALVES AVAILABLE: THRU VALVES AVAILABLE:

CAT. SIZE MOTOR OPER. MAX NO. TYPE VALVE PRES. W.P. KIT

ELS 2" FLGD. 228 FMA PB PC-S WO/TI 285 285 RFQELU 3" FLGD. 328 FMA PB PC-S WO/TI 285 285 RTSELX 4" FLGD. 428 FMA PB PC-S WO/TI 285 285 RTU

†To remove Piston 1807, use Spanner Wrench 1471SNW. To remove Pistons 1859 and 1863, use Spanner Wrench 1859SNW. Note: Drawing depicts 2" valve. Piston design varies, install with Spanner Wrench holes on top. For dimensions refer to Table of Contents.

EYS 2" FLGD. 228 FMT PB PC-S WO/TI 285 285 RFQ

*These are recommended spare parts and are stocked as repair kits.

CAT. SIZE MOTOR OPER. MAX NO. TYPE VALVE PRES. W.P. KIT

1

2

3

4

5

7

8

9

10

6

13

15

16

17

18

19

20

21

23

24

22

25

23

27

28

29

11

12

14

7

26

1

31

30

*

*

*

*

*

*

*

*

*

*

*

*

*

*

*

Kimray is an ISO 9001- certified manufacturer.

ITEM QTY. DESCRIPTIONPART NO.

2 INCH 3 INCH 4 INCH

1 2 LOCK NUT 173 906

2 1

SEAT 7498HSN 7499HSN ----

SEAT ---- 165HSN

SEAT DISC ---- 2494SS6

3 1 RATIO PLUG 332DEL 333DEL 334

4 1 GASKET 276 277 309

5 1 STEM 1809 327 328

6 1 CAGE ‡ 1751 1759 1761

7 2 O RING 774HSN 329HSN 1872

8 1 O RING 154HSN 155HSN 155

9 BOLT 1672 x 6 1672 x 8

10 1 STEM 2019 2394

11 1 STEM GUIDE 2463 2464

12 1 HOUSING 1729 2474 2475

13 NUT 241 x 8 241 x 10

14 BOLT 236 x 8 191 x 10

15 1 DIAPHRAGM 7053 743

16 1 BREATHER PLUG 147

17 1 SPRING 723 724

18 1 BONNET 1665 1655

19 1 UPPER DIAPH. PLATE 2576 1967

20 1 LOWER DIAPH. PLATE 2577 1968

21 1 O RING 1107HSN 639HSN 639

22 2 BACK UP 149T 150T

23 2 BACK UP 1685 1870 1871

24 1 CYLINDER 1679 1861 1865

25 1 O RING 808HSN 802HSN 2083

26 1 O RING 329HSN 330HSN 331

27 1 PISTON SEAL RETAINER 1806 1860 1864

28 1 PISTON 1807 1859 1863

29 1 ORING 265HSN 265HSN 265

30 1 REMOVABLE SEAT 1752PH 1760PH 1762PH

31 1

BODY

FLANGED ANGLE 1731 2471 2472

FLANGED THRU 3093 ---- 3095

2 LIFTING RING (not shown) ---- 7559

‡ Delrin Cage available on request for 4 inch valves

*

*

*

*

*

*

*

*

*

*

*

*

*

www.kimray.comE3:30.1

Issued 1/13Current Revision:Change Logo

LIQUID CAPACITY CHARTS

300 psig Maximum W.P. Valves

CAPACITY-Bbls. Water/Day, Steady Flow

For gravity correction, multiply the above figures byWhere “G” is the specific gravity of the flowing liquid.NOTE: Flow rates are for steady flow conditions over a 24 hour period. Corrections should be made to deal with intermittent flow conditions.

1G

PRESSURE DROP

ACROSS VALVEPSIG

VALVE SIZE - INCHES

2 3 4 6

12345

10152030405060708090

100120140160180200220240260280300325350375400

8001,1501,4001,6001,8002,5503,1003,6004,4005,1005,7006,2506,7507,2007,6508,0508,8509,550

10,20010,80011,40011,95012,50013,00013,50013,95014,50015,05015,60016,100

1,5002,1002,6003,0003,3504,7505,8006,7008,2009,500

10,60011,60012,55013,40014,20015,00016,40017,75018,95020,10021,20022,20023,20024,15025,05025,95027,00028,05029,00029,950

2,4003,4004,1504,8005,3507,6009,300

10,75013,15015,20016,95018,60020,10021,45022,75024,00026,30028,40030,35032,20033,95035,60037,20038,70040,15041,55043,25044,90046,50048,000

9,50013,45016,45019,00021,25030,05036,80042,50052,00060,05067,15073,55079,45084,95090,10094,950

104,050112,350120,150127,400134,300140,850147,150153,150158,900164,500171,200177,700183,900189,950

www.kimray.comE3:40.1

Issued 6/13Current Revision:Remove Cast Iron

BALANCED MOTOR VALVES

CAGE & HARD SEAT

NOTES:

Removable seat and cage is standard in Piston Balanced Motor Valves. But is optional in Diaphragm Balanced Motor Valve. To order specify valve model, then add “with removable seat.”

Kimray is an ISO 9001- certified manufacturer.

www.kimray.comE3:50.1

Issued 11/20Current Revision:Add thru LPHV valve

BALANCED MOTOR VALVES

DIMENSIONS

PB, DB, PBT ANGLE DIMENSIONS PB, DB, PBT THRU DIMENSIONS

VALVE A B C D E F2" S/FMA 6 1/2 9 8 1/2 4 1/4 3 4 1/43" S/FMA 8 1/2 11 3/4 10 1/4 5 1/2 3 3/4 5 1/24" FMA 8 1/2 12 1/2 11 6 1/2 4 1/2 6 1/26" FMA 10 3/4 — 19 3/4 10 1/4 5 1/2 7 11/16

VALVE A B C D E F2" SMT 6 1/2 10 3/8 9 7/8 2 1/8 — 8 1/22" FMT 6 1/2 10 3/8 9 7/8 — 3 93" SMT 8 1/2 13 5/16 11 9/16 2 7/8 — 123" FMT 8 1/2 13 5/16 11 9/16 — 3 3/4 12 3/164" FMT 8 1/2 14 7/8 13 3/8 — 4 1/2 15 1/86" FMT 10 3/4 — 19 3/4 — 5 1/2 22

VALVE A B C D E F2" SMT 9 1/16 12 13/16 4 7/16 2 1/8 8 1/2 32" FMT 9 1/16 12 13/16 4 7/16 2 1/8 9 1/8 33" SMT 12 7/8 17 5/32 5 29/32 2 7/8 12 3 3/43" FMT 12 7/8 17 5/32 5 29/32 2 7/8 12 3/16 3 3/4

LPHV THRU DIMENSIONSLPHV ANGLE DIMENSIONS

VALVE A B C D E F2" S/FMA 9 1/16 11 9/32 2 29/32 4 1/4 4 1/4 33" S/FMA 12 7/8 15 9/32 4 1/32 5 1/2 5 1/2 3 3/4