ORDER NO. CPD0511051C1

Personal Computer

CF-W4

Model No. CF-W4GWCZZ 1 2 1: Operation System B: Microsoft® Windows® XP Professional 2: Area

M: Refer to above area table

This is the Service Manual for

the following areas. M …for U.S.A. and Canada

© 2005 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law.

LASER SAFETY INFORMATIONFor U.S.AClass 1 LASER-ProductThis product is certified to comply with DHHS Rules 21 CFR Subchapter J.This product complies with European Standard EN60825 (or IEC Publication 825)For all areasThis equipment is classified as a class 1 level LASER product and there is no hazardous LASER radiation.

Caution: (1) Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. (2) The drive is designed to be incorporated into a computer-based system or unit which has an enclosing cover. It should never be used as a stand alone drive.

Danger:The serviceman should not remove the cover of drive unit and should not service because the drive unit is anon-serviceable part.Please check DANGER label on bottom cabinet of the equipment.

. Unplug the AC power cord and remove the battery pack from the equipment before opening the top cover of the drive. . When the power switch it on, do not place your eyes close to the top cover to look into the interior of the unit.LASER SpecificationClass 1 level LASER ProductWave Length: DVD 650 660 nm CD 778 787 nm

Laser safety information is appropriate only when drive with laser is installed.

HandlingThis computer has been designed so as to minimize shock to the LCD and hard disk drive, etc.,but no warranty is provided against such trouble. Therefore, as a precision instrument, beextremely careful in the handling.Do not carry the computer while the display is open, or carry it by gripping the display or thecabinet around the display (see figure A). When closing the display, ensure that the latch ispositioned correctly in the slot .Do not carry your computer when the power is on.Do not drop or hit your computer against solid objects.Remove all external devices, cables, PC Cards sticking out of the computer (see figure B),SD memory cards, and MultiMedia Cards before transporting the computer.We recommend preparing a fully charged battery pack.When transporting a spare battery pack inside a package, briefcase, etc., it is recommendedthat it be placed in a plastic bag so that its contacts are protected.Always carry your computer with you. Never check it in with luggage. For use of the com-puter inside an aircraft, we recommend asking the airlines regarding their policy on this issue.It is a good idea to make backup copies on disks and carry them with you.

A

B

Touch Pad

DisplayAvoid using water when cleaning the panel. Ingredients included in water may leave scratchesand reduce readability of the screen.<When cleaning dust/dirt>

Avoid rubbing off dust/dirt with cloth since it may leave scratch on the screen.Sweep dust/dirt with fine brush, then wipe it with a dry soft cloth used for cleaning glasses.

<When cleaning oily surface>Apply camera lens cleaner on a soft gauze and clean it with gentle force. Then, wipe with adry soft cloth used for cleaning glasses.

Areas excluding the displayWipe these areas with a soft cloth, after applying water or detergent diluted with water to thesoft cloth and firmly wringing out excess water.

Maintenance

Do not use benzene, thinner, or rubbing alcohol. Doing so may adversely affect thesurface, e.g., discoloration. In addition, do not use commercially-available householdcleaners and cosmetics, as they may contain components harmful to the surface.Do not directly add or spray water or detergent. If liquid enters the inside of thecomputer, it may cause it to work improperly or be damaged.

CAUTION

1 Connection Diagram

SD Card

Lithium Battery

Battery Pack

Inverter Board

DC-IN

PCMCIASLOT

Headphone Mic

WirelessLAN Module

Antenna Board(L)

Antenna Board(R)

Speaker

MODEM

SW6POWER SW

Touch Pad

LAN

Keyboard

DIMM memory(Option)

LCD

LCD Back Light

CN902CN901

VGA

USB

USB

CN601

CN11CN12

CN10

CN26

CN14

CN16

CN18

CN3

CN13

CN903

JK1JK2

SW951 Open SW

Main Board HDD

SW 7W-LAN ON/OFF

CF-BAV0256UCF-BAV0512U

CD-RW,DVD-ROM Drive

CN23

CN15

CN4

CN25

CN21

CN600CN2 CN19

CN951

USB Board

SW Board

Connection Cable 1 Drive FFC DFJK9000ZA 2 LCD Cable DFJS957ZA 3 Speaker Cable DFJS962ZA 4 SW Board FFC DFJE20T108BB 5 Antenna PCB-L N1ZYYY000002 6 Antenna PCB-R N1ZYYY000001 7 Modem Cable DFJS959ZB 8 LAN Cable DFJS979ZA 9 PAD FFC DFJE12U112BB 10 HDD FPC Unit DL3UP1443AAA 11 DC-IN Cable DFJS961ZB 12 Main-Sub Cable DFJS960ZA

Connection by Cable

Direct connection Connectors

Parts on Bottom Side

7

11

1

3

8

10

4

12

9

5

62

1-1

2 Disassembly instructions2.1. Disassembly Flow Chart

9.2.1.

9.2.2.

9.2.4.

9.2.6. 9.2.8.

Disk Cover

9.2.7. 9.2.9.

9.2.10.

Solenoid

9.2.11. 9.2.12. 9.2.13.

Drive Unit

9.2.3.

HDD

Main Board USB Board

9.2.14. 9.2.15. 9.2.16. 9.2.17.

9.2.19.

9.2.20.

9.2.18.

9.2.21.

9.2.5.

SW Board

Main Unit

Display Unit

LCD Unit

Hinge Cover

LCD Unit / LCD Rear

Inverter Board

Antenna Board(L, R) / DC-IN W-LAN Module MODEM Card Bus ejector

Keyboard

Top Case

Touch Pad

LCD Knob

Speaker

Preparation1. End the Windows.2. Turn off the Power, and then remove the AC Adaptor or Battery Pack.3. Remove any optional DIMM Memory Cards or PCMCIA Cards.4. Remove any other peripherals or Connected Devices.

9.2.1.

9.2.2.9.2.3.

9.2.4.9.2.5.

9.2.6.9.2.7.

9.2.8.9.2.9.

Battery PackDIMM CoverSide CoverKeyboardHDDHDD FFCHDD CoverTop CaseSW BoardDisk Cover Open KnobDisk CoverTouch PadTouch Pad KnobTouch Pad RingPAD FFCLCD KnobSpeaker

9.2.10.9.2.11.9.2.12.9.2.13.9.2.14.

9.2.15.

9.2.16.9.2.17.9.2.18.9.2.19.

9.2.20.

9.2.21.

SolenoidMain BoardDrive UnitUSB BoardAntenna BoardAntenna Cover(L, R)W - LAN ModuleHeat SpreaderMODEMCard Bus ejectorLCD UnitHinge CoverHinge (L, R)LCD UnitLCD RearLCD FrontInverter BoardLCD Cable

Main replaceable parts

2-1

2.2. Disassembly2.2.1. PreparationAttention:

Before disassembly, be sure to perform the following steps. 1. End the Windows. 2. Turn off the power and then remove the AC Adaptor. 3. Slide the Hooks (A) and then remove the Battery Pack. 4. Remove the Screw (A) and then remove the DIMM cover.

(Remove if the DIMM memory is equipped with)Screw(A):XSB2+4FNL(N16)

Screw (A)

DIMM cover

Battery Pack

Hook (A)

2.2.2. Remove the KeyboardPreparation : perform the section 2.2.1. first. 1. Remove the 4 Screws (F).

Screw(F):DXQT2+E12FNL(N11) 2. Remove the Keyboard Hook Plate and then remove the

Hook of back side of Keyboard with small screwdriver.

Screw (F)Screw (F)

Screw (F)

Keyboard Hook Plate

3. The LCD unit is opened up to about 90° by operating theLCD Knob.

4. Remove the 6 Hooks (B).

5. Open the Keyboard from LCD side and then turn it insideout on the Top Case.

LCD Knob Hook (B)

LCD unitHook (B)

6. Remove the Heat Spreader from buttom of the Keyboard. 7. Remove the Keyboard FFC from the Connector (CN15),

(CN26) and then remove the Keyboard.

Heat Spreader

CN26

Keyboard

CN15

2-2

2.2.3. Remove the HDDPreparation : perform the section 2.2.1. 2.2.2. first. 1. Remove the 2 Screws (V).

Screw(V):DFHE5025XA(N1) 2. The slide is done in the direction of the arrow and the HDD

Cover is removed.

Screw (V)

HDD Cover

3. Lift up the HDD Unit and remove the FFC Connector andthen remove the HDD Unit.

4. HDD is taken out of the HDD Case.Note:

Please do not bend pins of the HDD Connector, at thetime of removing HDD and FFC Connector.

HDD

FFC Connector

HDD UnitHDD FFC

HDD Case

2.2.4. Remove the Top CasePreparation : perform the section 2.2.1. , 2.2.2. first. 1. Insert a small screwdriver into the hole and slide the look in

the direction shown by arrow (C) to open the Disc Cover. 2. The Anttena Cover (R) is rotated from the Bottom Case side

in the direction of arrow (A) and the Antenna Cover (R)removed in the direction of arrow (B).

LCD unit

Antenna cover (R)

A

B

C

Small screwdriver

Hole

Back Side

3. Remove the 3 Screws (B), 2 Screws (C) and 3 Screws (E)from the Bottom Case.Screw(B):DRHM0092ZA(N4)Screw(C):DXHM0057ZA(N7)Screw(E):DXHM0039ZA(N6)

Screw (E)

Screw (C)

Screw (E)Screw (B)

Screw (E)

Screw (B)

Screw (B)

Screw (C)

2-3

4. Remove the 3 Screws (I), 2 Screws (J), 2 Screws (K) and 2Screws (L) from the Top Case.Screw(I):DXQT2+E6FNL(N13)Screw(J):DXQT26+D8FCL(N16)Screw(K):DXQT2+E6FCL(N12)Screw(L):DFHE5025XA(N1)

Screw (J)

Screw(J)

Screw (I)

Screw (I)

Screw (L)Screw (L)

Screw (K) Screw (K)

Screw(I)

Disc Cover

5. Lift up the Top Case, remove the Pad FFC and thenremove the Top Case.

FFC (SW)

Top Case

FFC (PAD)

2.2.5. Remove the SW BoardPreparation : perform the section 2.2.1. to 2.2.3. first. 1. Peel off the Tape. 2. Remove the Solenoid Cable. 3. Remove the 1 Screw (Q) and then remove the SW Board.

Screw(Q):DXHM0057ZANote:

Note it that the Disc Eject Knob comes off at the sametime.

Top CaseScrew (Q)

Disc Eject Knob

Switch Board

Solenoid Cable

Tape

2-4

2.2.6. Remove the Disc CoverPreparation : perform the section 2.2.1. to 2.2.3. first. 1. Remove the 2 Screw (R), 1 Screw (S) and 1 Screw (T) of

the Disk Angle.Screw(R):DXQT2+E12FNL(N11)Screw(S):DXQT2+E6FNL(N13)Screw(T):DXHM0057(N7)

2. Slide the Disc Cover to the Disc Cover Shaft and removethe Cover.

3. The Disk Cover Shaft is pulled out while sliding andremoved it from the Disk Angle in the direction of the TouchPad.

Screw (R) Screw (S)

Screw (R)

Disc Cover

Disk Cover Shaft

Top Case

Disc Cover Spring

Disk AngleScrew (T)

2.2.7. Remove the Touch PadPreparation : perform the section 2.2.1. to 2.2.3. first. 1. Peel off the Tape. 2. The 6 Hooks of the Pad Cover are depressed in the

direction of the center of the Touch Pad by using the smallscrewdriver.

Tape

Hook

Hook

Hook

Hook

PAD FFC

Top Case

3. Remove the Hooks of the Toutch Pad and the Pad Button,and remove the Touch Pad.

Hook (F)

Hook (F)

Pad Cover

Touch PadPad bottun

2-5

2.2.8. Remove the LCD KnobPreparation : perform the section 2.2.1. to 2.2.3. first. 1. Remove the Spring from the Top Case. 2. Remove the Hook of LCD Knob from the Stopper Rib of the

Top Case and then the LCD Knob is removed.

Location of the Spring

Stopper Rib

LatchSpring

Top Case

LCD Knob

2.2.9. Remove the SpeakerPreparation : perform the section 2.2.1. to 2.2.3. first. 1. Peel off the Speaker Box Sheet. 2. Peel off the tape on the Speaker and Speaker Ring and

then remove the Speaker.

Speaker Box Sheet

Speaker

SpeakerRing

Top Case

2.2.10. Remove the SolenoidPreparation : perform the section 2.2.1. to 2.2.3. first. 1. Remove the 1 Screw (Z) and then remove the Solenoid.

Screw(Z):DXQT2+F2FNL(N14)

Solenoid

Screw

2.2.11. Remove the Main BoardPreparation : perform the section 2.2.1. to 2.2.3. first. 1. Remove the 1 Screw (D), (H) and 2 screws.

Screw(D):DXQT2+E10FNL(N10)Screw(H):DXQT2+D4FNL(N9)Screw(G):DFHE5035ZB(N2)Screw(W):K1YE50000022(N500)

Screw (H)Screw (D)

Screw (G)

Screw (W)

2. Remove the 2 Screws (N).Screw(N):DXQT2+E6FNL(N13)

3. Remove the Connector (CN23)

2-6

4. The Antenna Cover (L) is inclined in the direction of arrowA and remove it.Remove the Antenna Cover (L) from the Top Case.

Antenna Cover (L)

Antenna PCB (L)

Screw (N)Screw (N)

Main Board Bottom CaseCN23

A

5. Remove the Connectors (CN10) and (CN11) of LCD Cable.

CN10

CN11

LCD Cable

6. Remove the DC-IN Jack Holder.

DC JackHolder

Main Board Bottom Case

7. Returns the Main Board on the reverse.Peel the Tape of the Drive FFC and remove the FFC.

8. Remove the Connector (CN3) and the Connector (CN16) ofLAN Cable.Peel off the Tape of HDD FFC and remove the FFC.Remove the Main Board.

CN3

LANcable

CN16Lithium BatteryCable

TapeTape

2-7

2.2.12. Remove the Drive UnitPreparation : perform the section 2.2.1. to 2.2.3. first. 1. Peel off the Tape from the Connector. 2. Remove the Drive FFC from the Connector (CN501) and

remove out the Drive Unit.

TapeCN501

Drive FFCDrive unit

2.2.13. Remove the USB BoardPreparation : perform the section 2.2.1. to 2.2.3. first. 1. Remove the Connector (CN23) on the Main Board. 2. Remove the USB Board from the Bottom Case.

CN23

USB Board

USB Cable

2.2.14. Remove the Antenna Board(L,R)Preparation : perform the section 2.2.1. to 2.2.10. first. 1. Remove the Antenna Cable (L, R) on the Wireless LAN

Module and then remove the Antenna Board from theBottom Case.

2. Remove the DC-IN Cable (CN600) from the Main Board.

CN600

DC - IN CableBottom Case

Antenna Cable (L)

Antenna Cable (R)Antenna PCB (L)

2.2.15. Remove the Wireless LAN ModulePreparation : perform the section 2.2.1. to 2.2.3. and 2.2.10.first. 1. Peel off the Tape on the Wireless LAN Module. 2. Open the Wireless LAN Module maintenance arm and

remove the Wireless LAN Module.

Tape

Wireless LANModule

Main Board

2-8

2.2.16. Remove the MODEMPreparation : perform the section 2.2.1. to 2.2.3. and 2.2.10.first. 1. Remove the 2 Screws (O).

Screw(O):DXQT2+D25FNL(N8) 2. Remove the MODEM to the vertical direction from

Connector (CN8) on the Main Board.

Screw (O)Screw (O)

CN18

MODEM

2.2.17. Remove the Card Bus EjectorPreparation : perform the section 2.2.1. to 2.2.3. and 2.2.10.first. 1. Remove the 1 Screw (P) from connected side of Main

Board.Screw(P):DFHE5025XA(N1)

Main Board

Screw (P)

2. Return it on the revers to Card Bus Ejector side. 3. Remove the 2 hooks (C) of the Card Bus Ejector from the

Connector (CN14) and the Card Bus Ejector is removed.

Main Board

Card Bus Ejector

Hook(C)

CN14

2-9

2.2.18. Remove the LCD UnitPreparation : perform the section 2.2.1. to 2.2.3. first. 1. Remove the 2 Screws (M)

Screw(M):DXQT26+D5FNL(N15) 2. Remove the LCD Cable from the Connectors (CN10) and

(CN11) on the Main Board and then remove the LCD Unit.

CN10

CN11

Screw (M)

Screw (M)

LCD Cable

Bottom Case

2.2.19. Remove the Hinge CoverPreparation : perform the section 2.2.1. to 2.2.3. and 2.2.18.first. 1. Remove the 2 Screws(U) and the Hinge Cover(L,R).

Screw(U):DRHM0074ZA(N3)

Hinge Cover (L)

Hinge Cover (R)

Screw (U)

Screw (U)

LCD Unit

2.2.20. Remove the LCD Unit and the LCDRear

Preparation : perform the section 2.2.1. to 2.2.3. and 2.2.18.to 2.2.19. first. 1. Remove the 2 Screws (Y).

Screw(Y):DRHM0074ZA(N3)

Screw (Y)

Screw (Y)

LCD Unit

2. The LCD Front Case and the combination parts of LCDRear Case are separated.(Combination parts are 6 the top and bottom places foreach, 4 right and left places for each)

3. Remove the Hinge (L, R).

Hook Position

Hinge (L)

Hinge (R)

LCD Front Case

LCD Rear Case

LCD Unit

2-10

2.2.21. Remove the Inverter BoardPreparation : perform the section 2.2.1. to 2.2.4. and 2.2.17.to 2.2.19. first. 1. Remove the LCD Cable from the Inverter. 2. Peel off the Tape for fixation from Inverter Case. 3. Remove the Inverter with the Inverter Case.

LCD Hook

Gasket Cloth

Inverter Box

Tape

LCD Cable

LCD High voltage2pin Wire Rod

LCD Front Case

2-11

3 Reassembly instructions3.1. Attention when CF-W4G series is repaired · Please execute writing BIOS ID when you exchange the Main Board. · Parts (Sheet and rubber) etc. related various the Conductive Cloth and Heat Spreader cannot be recycled. Use new parts.

3.2. Assembly knowhow of part LCD

LCD Rubber (Upper)

LCD Side Rubber

LCD Back Rubber (Lower)

LCD Front Case

LCD Front Case

LCD Rubber (Upper

LCD parallel after puttingbig small

LCD Rubber, LCD side Rubber and LCD backing Rubber’s putting

0 1mm

1 2mm

1 2mm

LCD Cable processingClamping processing of LCD Cable, LCD Connector connection and putting of PET Tape of cable

The LCD Insulation Sheet is peeled off and after processes as shown in the figure below, Put the Insulation Sheet.

LCD Frame Clamp

A red line of the cable is matched to the LCD Frame externals.

Connector

PET Tape

LCD Insulation Sheet

Insulation seat of edge match0 1mm

Connector of externals match There must not be beginning to see from externals.

Conductive Cloth(LCD Label)

Putting of The Conductive Cloth

The Conductive Cloth is put and after putting, a both side tape is put. Process the part in the signal line of the LCD Cable in the Conductive Cloth.Put the Conductive Cloth on the connector surely.

LCD Insulation Seat

Connector

Both Side Tape LCD Cable

3-1

PET Tape

Putting of Rear Damper

Putting of PET SheetThe cable must not run aground on the damper. Along the LCD Module and put the LCD Cable (Inverter part) with the PET Tape.

Conductive Cloth (LCD cable)

LCD Cable

LCD Cable(Inverter part)

Damper

Conductive Cloth (LCD cable)

LCD Cable

Rib application putting of LCD Front Case0 1mm

Externals suiting of Inverter Case0 1mm

Rear Damper

Processing of Inverter Cable

The cable must not run aground on the cushion.

The cable must not come in succession.

Inverter Cable

The line of the remainder is put on Hinge (R) side.

Hinge (R)

Put the reflector part surely.

Put on Hinge (R) surely.

Gasket (LCD)

Externals suiting of reflector0 1mm

Putting of Gasket (LCD)

3-2

Putting of LCD Damper(C)

Rib edge match of LCD Front Case0 1mm

Rib application putting of LCD Front Case0 1mm

LCD Damper(C)

Plinth externals match0 1mm

Rib application putting of LCD Front Case0 1mm

Conductive Cloth is wrapped (Leave the half) 75 5mm

LCD Cable (Inverter)

Putting of Conductive Cloth of LCD Cable

The Cable is processed under the shaft .

Note:It is confirmed that the cable does not narrow between cabinets.

Drawing out specification of LCD Cable

0 1mm0 1mm

Put the Conductive Cloth

The cable is processed to the ditch

Processing cable to under point hanging part

Processing the cable to the DC-IN Jack Holder

LCD cable processing 1 LCD Cable processing 2Process the LCD Cable (2) such as DC-IN Jack Holders, after process the Conductive Cloth of the LCD cable puts as shown in the figure below.

Connector connection specification

The order of connecting connectorInverter Cable LCD CableDC-IN Jack Holder

3-3

3.3. Assembly of Brake Lever

Brake Lever built-in figure

The above is shape.

In the slide and then install.

Brake lever preparation goods

Surface chart

Brake Lever completion chart

Do not touch the bonding side when the brake pad is affixed.

Brake Spring

Brake Lever

Brake Pad

The back chart

Be sure not to do the slide with struck the rib.

3-4

3.4. Solenoid Wire Rod processing

Solenoid with cable

Inserts under the rib

Disk Cover Lock

Inserts between ribs

Up that there is no screw hole

The Solenoid with the cable is made on the Disk Cover Lock

Solenoid Cable

3.5. Switch Board assembly specification

SW Board FFC

SW Board

Disk Eject KnobScrew

Tape

To confirms that the Lever of the switch has been surely inserted in the ditch of the knob

Central suiting with the pin

0 1mm

0 1mm

0 1mm

Terminal Side

Fold as valley type

Suiting with shape of case

Suiting with shape of board

SW Board FFC

Connection to SW Board Affixation of PET Tape

Pin

3.6. Speaker installation and Line processing

Affixation of Speaker Ring

Put it according to the shape of the rib. Note not running aground in the rib.

Speaker Cable

Speaker

Soldering Soldering

Black LineRed Line

Soldering of Speaker Cable

Speaker Ring

Rib

Rib

3-5

0 1mm

Inserts in ditch

Inserts in latch

Inserts in the table side.

Rib outside suiting

0 1mmRib outside suiting

Processing of Speaker Cable Speaker installation

Speaker BoxSecure 2mm or more for the space in each rib

and the soldering part.

Rib

Soldering Part2mm or more

Rib

Rib

Rib

2mm or more

Inserts in Ditch

3.7. Assembly of Antenna Board Part

Place between the bottom baseand install.

Antenna Cable (L)

Install DC Jack in bottom

Process the cablewith the boss between ribs.

Process the cable to the ditchof the Bottom Case.

The terminal must becomestraight below.

Antenna Cable (L)

Boss

Bottom Case

Install the Antenna Board in the Bottom Case. And process remainder of the Antenna Cable as shown in the figure below.

Line processing of Antenna Cable (L)

DC Jack Holder

The under latch is hooked the Bottom CaseThe under latch is hooked

the Bottom Case

Antenna Cover(L)

The upper side is close with the under latch is hookedthe Bottom Case

3-6

3.8. MODEM Cable, Rib and LAN Cable processing

Main Board

LAN Cable

Modem Cable

0 1mm

1 3mm

Standard size8mm

Tape is wrapped

Modem Cable

Gasket Cloth

Wrap Gasket Cloth.

Tape

Conductive Cloth affixation of Modem Cable

Process between theMain Board and the Pin.and do LAN Cable up. (Prevent from floating by Modem Cable.)

Process the Modem Cable tothe cutting lack of the Board.

PETTape

Process the cable so as not tocome in succession.

PETTape

PinPin

Pin

MODEM

LAN

Touch the pin.

Touch the pin.

Draw out RJ cablestraight.

Divide the cable into the centerand paste the tape vertically.Paste the remainder to an opposite side.

Peel off the both sides tapeflaking off paper and then fix to the cover.

Process at theright of the pin. Do not get on up.

Process underthe pin.Do not get on up.

Process the remainderbetween the pin and the pin.

Process the cable tothe cutting lack part.

Install connector in bottom.

Shut the cap.

3-7

3.9. USB Cable processing

Open space between the Drive Board and the cable.

Process the USB cable on the Drive Board. Do not multiply the stress by the Drive Board.

Put the cable when there is no spacebetween the Main Board and the cablein the Main Board.

USB Cable

DriveMain Board

Process between the pin and the pin. Process between the boss and the HDD.

Process between the pinand the Main Board.

Fix the substratewith two pins.

USB Board

HDD FFC

PinUSB Cable

Boss

3.10. Wire Rod processing of Lithium Battery

0 3mmTape

Draw out the cable straight.

Paste to round shape of the Bottom Case.

0 2mm

Boss

Process the Antenna Cable between the Lithium Battery and the Boss.

3-8

3.11. Affixation of HDD Gasket

HDDHDD Case

Insertion

0 1mm

0 1mm

Affixes in the corner of concave part. Do not run aground on difference.

Gasket

3-9

3.12. Assembly of Disk Cover

Paste the remainder internally.(The other side is also the same.)

Disk Angle

0 1mm

0 1mm 20 1mm

0 1mm

0 1mm

0 1mm

0 1mm0 1mm

0 1mm

0 1mm

Prevention rubberwith disk wound

Installation of various dampers on Disk Angle

Installation of Disk Cover

Disk Angle

Tape for Keyboard

Disk Cover Shaft

Prevention rubber with disk wound is pasted.

Tape for Keyboard/Seat 2 is pasted.

LCD Cushion is pasted.

LCD Cushion LCD Cushion

Insert the latch of The Disk Angle in the corner hole of the Disk Cover Shaftand slide of the Disk Cover in the direction of the arrow.

Disk Angle Insert the hook in the corner hole.

Do the Disk Cover in the slide.

Arrange Disk Cover Shaft Z bendpart at the left of the bendof the Disk Angle.

<Figure before installations> <Figure after installations>

Suit a round hole.

Arrange Disk Cover Shaft Z bend partunder the bend of the Disk Angle.

Disc Cover

PAD Cover Ring

Arm spring forDisk Cover

Convex part

Latch

Convex part

Insert underthe Hook

Assembly of Disk CoverInstallation of PAD Cover Ring Installation of Disk Cover Shaft

Pin 2 Pin 1

Insert two Convex parts in the hole of Disc Cover.Hang two latch on Disc Cover.

Insert the Arm Spring for the Disk Cover in the Disk Cover. Insert pin 1 of the Disk Cover Shaft through the

inside diameter of the Spring. Pin 2 of the Disk Cover Shaft must be slided,

and insert in the hole of the Disk Cover.

Disk Cover Shaft

3-10

3.13. Assembly of Touch Pad

The Concave part is insertedin the hole of a Top Case

Touch Pad

Affixes it according tothe convex positioned part

Pressurizing

Hook

Hook

Gasket (PAD)

PAD Button

PAD Seat

Pad Cover

PAD FFC

Touch Pad

Pin insertion

Top Case

Affixes it according to the insideconcave part edge side

Convex part

Insertion of PAD FFC Installation of Pad Button Affixation of PAD Sheet

Affixation of Touch Pad Installation of Pad Cover

Insert two places in the convex partin the ditch of a Top Case and hangHooks four places.

3.14. Screw tightening procedure of each unitWhen serving, the screw tightening is executed according to the undermentioned procedure. 1. Screw tightening of Top Case

1-1. DXQT2+E6FNL(I:N13) is tightened. No.1 to No.31-2. DFHE5025XA(L:N1) is tightened. No.4 to No.61-3. DXQT2+E6FCL(LK:N12) is tightened. No.7, No.81-4. DXQT26+D8FCL(J:N16) is tightened. No.9, No.10

Screw (J)

Screw (J)

Screw (I)

Screw (I)

Screw (L)Screw (L)

Screw (K)

Screw (K)Screw (I)

Screw (L)

A

Conclude coloring part A pressing when you conclude Screw (K).

3-11

2. Installation of Keyboard1.The Keyboard is surely installed in the Hook (2 places) at the right and the Hook (4 places) behind a Top Case .2.The Keyboard is held and the Keyboard Hook is inserted and locked.Note:Never touch the edge part of the Keyboard Hook by bare-handed.3.It is confirmed that the Keyboard Hook do not run aground in the rib.

Keyboard Hook plate

Keyboard

Screw tightening of Keyboard

Hook

Hook

Hook

Do not run aground on the rib(Refer to the figure below)

Keyboard Hook plate

Keyboard Hook plate

OK

NG

Top Case

3. Screw tightening of Bottom Case1.The screw tightening is done in the undermentioned order.3-1. DXHM0039ZA(E:N6) is tightened.No.1 to No.33-2. DXHM0057ZA(C:N7) is tightened. No.4,No.53-3. DXQT2+E12FNL(F:N11) is tightened. No.6 to No.93-4. DXQT2+E10FNL(D:N10) is tightened. No.103-5. DXQT2+D4FNL(H:N9) is tightened. No.113-6. DRHM0092ZA(B:N4) is tightened. No.12 to No.14

Screw (H)

Screw (E)

Screw (C)

Screw (D)

Screw (F)

Screw (E) Screw (F)

Screw (F)

Screw (B)

Screw (E)

Screw (B)

Screw (B)

Screw (C)

Screw (F)

3-12

3.15. Specification of affixation of PET tape to Heat Spreader

1~2mm

1~2mm

<The Main Board Side> <The Back Completion Chart>

Heat Radiation Grease(G-751)Spread with a treatment device.

Heat Spreader

PET Tape

PET Tape

The extent that length remains pastes on an opposite side.

The extent that length remains pastes on an

opposite side.

Never touch the aluminum edge part directly by bare-handed when the part of aluminum with a thin all surroundings bends. Correct in that case with a radio pincers etc. and instal.

3.16. Affixation of Win Logo Label (XP), CENTRINO Label and ENERTGYSTAR Label

In Win Logo Label / CENTRINO Label / ENERGY STAR Label Affixation inclination, the both ends difference is within 0.2mm.

2 5mm

2 5mm

0 1mm

2 5mm5 7mm

Win Logo Label (XP)

CENTRINO Label

ENERGY STAR Label

3-13

K37

K92

K42

K19

K37

N3

K33

K85

K30

K12

K30

K33

N3

K51K51

K51

K53

K52

K52

K51

K51

K8

K88K81

N3

K82N3

K5

N15

N15

K6

K63

K39

K23

K39

K64

E26

K99

K63

K38K38

K39

K39

E24

K22

K45

K18

E5

K36

Display Section

Exploded View

Screw tightening torque

N7

K97

K525

a

a

K113

K111

K511

K112K89

K10

K114

E27

E2

K9

K106

K94

K503K504

K505

N8

K502

N7 N11

K506

K506

K91 N11

N13

K506

K69K69

K500

E28

K50K1

K20

K49

K508K17

K60

E23

K59

K90

K501

N16

N1

N12N13

N12

N1

N1

N16

N13

E10

K101

K61

N13

K46

K117

E3E13

SW951

K76K76

K93

K44

K41

K16K123

K7

E25

N14

K35 K35K35

K35

K520

K519

K116K115

K4

K522

K119K523

K523K507

K74

PETTape

Cabinet Section

Screw tightening torque

K96

N11

N9

CN13

CN12

CN22CN14

JK2

JK1

N1

SW6SW7

SW5

K86-1

K86-1

K86-1

N4

N4

N11

N17

N10N6

N6

N7

N7

N4

N6

N11N11

K3K2 K86-3

N2

E14

K79

K34

K86-2

E9

K108

N8

K102

K110

K510

K32

K104

K98

K107

K109

K524

K24

N5

K509

N500

K517

E19

K27

K49

E4

A3

E6

E7

E8E12

CN902

CN903

E1

K86-2

K86

K80E16

K11K84

K515

K40

E21E20

N1

N1

K516

K518

K100E22

E29

N13

CN601

E11

K43

E18

N8

K29

K105

K515

K515

K513

K512

K521

K514

Bottom Section

Screw tightening torque

Replacement Parts List Note: Important Safety Notice Components identified by mark have special characteristics important for safety. When replacing any of these components, use only manufacturer's specified parts.

CF-W4GWCZZBM

REF.NO. and AREA PART NO. DESCRIPTION Q'TYMain Block UnitE1 CR-2032/K5A COIN BATTERY 1E2 DFJK12U112BB PAD FFC 1E3 DFJK20T108BB SW PCB FFC 1E4 DFJK9000ZA DRIVE FFC 1E5 DFJS957ZA LCD CABLE 1E6 DFJS979ZA LAN CABLE 1E7 DFJS959ZB MODEM　CABLE 1E8 DFJS960ZA MAIN SUB CABLE 1E9 DFJS961ZB DC-IN CABLE 1E10 DFJS962ZA SP CABLE 1E11 DL3U11436MAB PCB, MAIN RTL 1E12 DL3U21436MAB PCB, USB RTL 1E13 DL3UP1492KAA PCB, SW RTL 1E14 N1ZYYY000002 ANTENNA PCB-L ASSY 1E16 N1ZYYY000001 ANTENNA PCB-R ASSY 1E18 N5HZC0000014 WIRELESS LAN MODULE 1E19 UJDA769PD1-A CD-R/RW, DVD-ROM DRIVE 1E20 DL3UP1443AAA FPC, HDD 1E21 N3CABRD00011 HDD 1E22 K1YYZZ000060 CONNECTOR 1E23 L0AA01A00018 SPEAKER 1E24 L5EDD3Q00023 LCD 1E25 L9AAA5DB0010 SOLENOID 1E26 N0GB1J000012 INVERTER 1E27 N2AZZJ000038 KEY BOARD US 1E28 N2EAYYY00001 TOUCH PAD 1E29 N5HAZ0000012 MODEM 1AccessoriesA1 CF-AA1623AM6 AC ADAPTOR 1A2 K2CG3DR00003 AC CABLE 1A3 N4HULTA00009 LITHIUM ION BATTERY PACK 1A4 DFQX5574ZA MANUAL 1A500 DFJS954ZA MODEM CABLE 1Packing MaterialP1 DFPE0806ZA HOLDER 1P2 DFPE0812ZA PAD W 1P3 DFPE0819ZA BATTERY SPACER 1P5 DFPK1037ZA ACCESSORIES BOX 1P6 DFPK1180YA PACKING CASE (EXPORT) 1P7 DFPN0827ZA CUSHION T 2P8 DFPN0828ZA CUSHION B 2Mechanical PartsK1 DFBC0314ZB-0 PAD BUTTON 1K2 DFBD0180ZB-0 POWER KNOB 1K3 DFBD0182ZA-0 LAN SW KNOB 1K4 DFBD9006ZA-0 DISK EJECT KNOB ASSY 1K5 DFBH3043ZA HINGE-L USA 1K6 DFBH3044ZA HINGE-R USA 1K7 DFBS0068ZC-0 LCD KNOB 1K8 DFGB0089VB-0 PANASONIC LABEL 1K9 DFGE0106ZB-0 PAD COVER 1

K10 DFGE0107ZB-0 PAD COVER RING 1K11 DFGT1028ZA BOTTOM SHEET USA 1K12 DFGX0397ZA-0 LCD BATT RUBBER 1K16 DFHE0215ZA SHEET 1K17 DFHE0416ZA TAPE (KBD) 2K18 DFHE0436ZA CLOTH LCD CABLE 1 1K19 DFHE0843ZA LCD MAGNET 1K20 DFHE0844ZA GASKET PAD 1K22 DFHE0943ZA GASKET CLOTH (LCD CABLE) 1K23 DFHE0945ZA GASKET CLOTH (LCD) 1K24 DFHE0953ZA SHEET 1K27 DFHE0957ZA GASKET CLOTH 1K29 DFHG1471YA LCD METAL DAMPER B 1K30 DFHG1546ZB-0 LCD RUBBER 2K32 DFHG1744ZA M-PCI CUSHION 1K33 DFHG1766ZA-0 LCD SIDE RUBBER 2K34 DFHG1767ZA-0 DC JACK HOLDER 1K35 DFHG1768YA-0 DISK COVER CUSHION 4K36 DFHG1771ZA LCD DAMPER A 1K37 DFHG1772ZA LCD DAMPER B 2K38 DFHG1773ZA LCD DAMPER C 2K39 DFHG1774ZA LCD SIDE DAMPER 4K40 DFHG1808ZA HDD CASE ASSY W4 USA 1K41 DFHG1778ZA PCMCIA STOPPER CUSHION 1K42 DFHG1779WA LCD HOOK CUSHION 1K43 DFHG1786ZA CPU CUSHION 1K44 DFHG1787ZA MINI-PCI CUSHION 1K45 DFHG1797ZA REAR DAMPER 1K46 DFHG1800ZA BATT CUSHION(W4) 1K49 DFHP7106YA BOTH SIDES TAPE 2K50 DFHP7221YA PAD SHEET 1K51 DFHP7208YA LCD FRONT TAPE A 5K52 DFHP7209ZA LCD FRONT TAPE B 2K53 DFHP7210ZA LCD FRONT TAPE C 1K59 DFHR3A37ZA SPEAKER RING 1K60 DFHR3A38ZA SPEAKER BOX 1K61 DFHR3A71YA DISK EJECT KNOB SHEET 1K63 DFHR3A78ZA LCD INSULATOR 2K64 DFHR3A95ZA INVERTER TAPE 1K69 DFHR3B19ZA HINGE BACKUP SHEET T4 1K74 DFHR3B53ZA DISK KNOB SHEET 1K76 DFHR6188ZA DISK LOCK BUSH 2K79 DFKE0772ZA-0 ANTENNA COVER-L 1K80 DFKE0773ZA-0 ANTENNA COVER-R 1K81 DFKE0774ZA-0 HINGE COVER L 1K82 DFKE0775ZA-0 HINGE COVER R 1K84 DFKE0815ZA-0 DIMM COVER LIGHT 1K85 DFKF0255ZB-0 LCD FRONT 1K86 DFKF8165ZA-0 BOTTOM CASE USA ASSY 1K86-1 DFHG371ZA-1 FOOT RUBBER 3K86-2 DFKL0026ZA-0 FOOT RUBBER BACK 2K86-3 DFMX1174ZA AUDIO JACK SHEET 1K88 DFKM0482ZA-0 LCD REAR (SANKI) 1K89 DFKM0483UA-0 DISK COVER (TOUGH COMBO) 1K90 DFKM8170VA-0 TOP CASE ASSY 1K91 DFKE0817ZA DISK ANGLE MG 1K92 DFMD1189XA LCD HOOK 1K93 DFMD1190YA DISK COVER LOCK 1K94 DFMD2165ZA DISK CV SHAFT ANGLE 1K96 DFMD3121ZA MDC PLATE 1

K97 DFMD4057ZA KB HOOK F999 1K98 DFMX0635ZB SHEET 1K99 DFMX1155ZA INVERTER BOX 1K100 DFMX1156ZA MAIN PW SHEET1 1K101 DFMX1158ZA DVD PWB SHEET 1K102 DFMX1160ZA PCMCIA-MAIN SHEET 1K104 DFMX1184ZA SW CABLE SHEET 1K105 DFMY0399ZA MCH RUBBER 1K106 DFMY3191YA HEAT SPREADER TOP 1K107 DFMY3192ZA HEAT SPREADER BOTTOM 1K108 DFMY3206ZA MEMORY SHEET TOP 1K109 DFMY3207ZA MEMORY SHEET BOTTOM 1K110 DFMY3208ZA WLAN SHEET 1K111 DFQT9950ZA WINDOWS XP LABEL (FOR NOTE) 1K112 DFQT9948ZA CENTRINO LABEL 1K113 DFUD0037ZA DISK KNOB SPRING 1K114 DFUN0078ZB DISK COVER ARM SPRING 1K115 JDBC0044ZA BREAK SPRING 1K116 JDBG0032ZA BREAK PAD 1K117 JDKJ0059ZA BREAK LEVER 1K119 DFHP7180ZA LCD TAPE E 1K123 DFUD0040ZA LATCH SPRING 1K500 DFHR3C40ZA DISK COVER SHEET 1K501 DFHR3C14ZA LCD KNOB SPACER 2K502 DFHR3C36ZA DISK ANGLE SHEET A 1K503 DFHR3C37ZA DISK ANGLE SHEET B 1K504 DFHR3C38ZA DISK ANGLE SHEET C 1K505 DFMD7A63ZA DISK ANGLE FPC COVER 1K506 DFHG1833ZA DISK ANGLE CUSHION 3K507 DFHP7226ZA KB FPC TAPE 1K508 DFHR3C39ZA KB SHEET 1K509 DFHR3C33ZA LCD CABLE FIX SHEET 1K510 DFHR3B86ZA DVD HEAT INSULATION PACK 1K511 DFQT9675ZA ENERGY STAR LABEL 1K512 DFKE0781ZA-0 RJ DUST COVER 1K513 DFHP7228ZA RJ DUST COVER FIX TAPE 1K514 DFHG1835ZA HDD DAMPER 1K515 DFHR3C13ZA RJ CABLE SHEET 4K516 DFHR3C19ZA HDD FPC EDGE SHEET 1K517 DFHR3C24ZA USB CABLE FIX SHEET 1K518 DFKE0770ZA-0 HDD COVER 1K519 DFHG1834ZA SP CABLE FIX CUSHION 1K520 DFHP7231ZA KBD TAPE 1K521 DFHR3B99ZA RJ CABLE BLIND SHEET 1K522 DFHR3C12ZA SP CABLE SHEET 1K523 DFHR3C18ZA KB EDGE SHEET 2K524 DFHR3C54ZA HINGE BACKUP SHEET 1K525 DFMY0421ZA HEAT SHEET KB LARGE 1N1 DFHE5025XA SCREW 6N2 DFHE5035ZB SCREW 2N3 DRHM0074ZA SCREW 4N4 DRHM0092ZA SCREW 3N5 DRQT2+G6FKL SCREW 1N6 DXHM0039ZA SCREW 3N7 DXHM0057ZA SCREW 4N8 DXQT2+D25FNL SCREW 6N9 DXQT2+D4FNL SCREW 1N10 DXQT2+E10FNL SCREW 1N11 DXQT2+E12FNL SCREW 6N12 DXQT2+E6FCL SCREW 2

N13 DXQT2+E6FNL SCREW 6N14 DXQT2+F2FNL SCREW 1N15 DXQT26+D5FNL SCREW 2N16 DXQT26+D8FCL SCREW 2N17 XSB2+4FNL SCREW 1N500 K1YE50000022 SCREW, I/O PIN 2

Replacement Parts List

CF-W4GWCZZBMPART NO. DESCRIPTION Q'TY

MAIN PCBC 2 F1J0J106A024 CAPACITOR, 6.3V, 10µF 40C 3C 4C 6C 7C 8C 11C 12C 13C 15C 16C 17C 19C 20C 21C 23C 24C 25C 26C 29C 30C 31C 32C 34C 35C 36C 37C 40C 41C 42C 43C 45C 46C 47C 48C 63C 66C 67C 100C 103C 5 EEFCD0D151ER CAPACITOR, 2V, 150µF 2

Note: Important Safety Notice Components identified by mark have special characteristics important for safety. When replacing any of these components use only manufacturer's specified parts.

REF. NO and AREA

C 688C 9 F1G1C104A042 CAPACITOR, 16V, 0.1µF 169C 10C 14C 18C 22C 27C 33C 38C 39C 44C 60C 61C 69C 71C 72C 73C 78C 79C 80C 82C 83C 86C 91C 92C 101C 104C 110C 113C 115C 116C 119C 120C 121C 122C 125C 126C 127C 128C 131C 132C 134C 135C 138C 139C 142C 143C 144C 152C 153

C 154C 155C 161C 162C 163C 164C 165C 166C 167C 171C 187C 194C 195C 196C 197C 200C 202C 203C 206C 207C 210C 211C 213C 214C 215C 217C 220C 221C 222C 223C 228C 229C 230C 231C 232C 233C 234C 235C 236C 237C 239C 241C 242C 246C 247C 249C 250C 253C 257C 258

C 270C 278C 279C 280C 281C 283C 284C 293C 304C 307C 308C 309C 311C 313C 314C 315C 316C 317C 318C 319C 323C 328C 329C 331C 332C 333C 334C 336C 337C 338C 339C 341C 342C 343C 344C 345C 346C 349C 350C 364C 367C 368C 388C 391C 392C 394C 399C 401C 402C 403

C 408C 409C 412C 413C 417C 429C 430C 431C 432C 434C 435C 442C 443C 444C 446C 605C 609C 625C 631C 702C 49 F1J0J1060004 CAPACITOR, 6.3V, 10µF 25C 54C 74C 81C 89C 90C 102C 106C 107C 111C 169C 174C 180C 181C 184C 291C 292C 352C 353C 354C 355C 356C 404C 433C 723C 50 F1G1E103A062 CAPACITOR, 25V, 0.01µF 28C 170C 172C 173C 175

C 178C 179C 182C 183C 201C 219C 238C 262C 264C 266C 296C 305C 327C 369C 376C 378C 385C 415C 416C 601C 678C 729C 730C 55 F1G1H222A450 CAPACITOR, 50V, 2200pF 1C 56 F1G1A104A014 CAPACITOR, 10V, 0.1µF 3C 57C 191C 70 F1H0J1050022 CAPACITOR, 6.3V, 1µF 6C 88C 112C 145C 168C 185C 75 F1G1H102A450 CAPACITOR, 50V, 1000pF 33C 255C 256C 290C 297C 298C 325C 326C 359C 365C 366C 387C 389C 390C 395C 396C 397

C 407C 414C 418C 419C 420C 421C 422C 423C 616C 621C 632C 633C 659C 667C 679C 690C 76 EEFUD0D331ER CAPACITOR, 2V, 330µF 4C 77C 84C 85C 87 EEFSX0D271ER CAPACITOR, 2V, 270µF 4C 648C 649C 650C 93 F1G1A474A018 CAPACITOR, 10V, 0.47µF 7C 94C 95C 97C 98C 99C 254C 96 F1G0J224A001 CAPACITOR, 6.3V, 0.22µF 5C 109C 300C 301C 360C 105 EEFCD0D101ER CAPACITOR, 2V, 100µF 4C 652C 686C 696C 108 EEFUD0E221ER CAPACITOR, 2.5V, 220µF 3C 212C 218C 114 DCUM1A1051BD CAPACITOR, 10V, 1µF 26C 117C 118C 123C 124C 129C 130

C 133C 136C 137C 156C 157C 158C 159C 192C 198C 199C 204C 248C 310C 400C 427C 606C 635C 703C 706C 140 F1G1H3R3A475 CAPACITOR, 50V, 3.3pF 2C 141C 147 F1G1H101A451 CAPACITOR, 50V, 100pF 10C 294C 295C 299C 393C 607C 636C 637C 638C 680C 176 F1G1H220A451 CAPACITOR, 50V, 22pF 8C 177C 611C 647C 660C 664C 683C 725C 190 F1G1H4R0A543 CAPACITOR, 50V, 4pF 2C 193C 259 F1G1H100A452 CAPACITOR, 50V, 10pF 8C 260C 261C 263C 265C 267C 268C 269C 271 F1G1H330A451 CAPACITOR, 50V, 33pF 7

C 272C 273C 274C 275C 276C 277C 285 ECJ2FF1A106Z CAPACITOR, 10V, 10µF 5C 302C 312C 370C 373C 288 ERJ2GEJ103X RESISTOR, 1/16W, 10KΩ 1C 320 F1G1H6R0A452 CAPACITOR, 50V, 6pF 2C 322C 324 F1L3D102A003 CAPACITOR, 2000V, 1000pF 1C 347 F1J0J475A009 CAPACITOR, 6.3V, 4.7µF 6C 348C 436C 620C 642C 685C 351 F1G1H471A450 CAPACITOR, 50V, 470pF 2C 634C 357 F1H1A105A030 CAPACITOR, 10V, 1µF 4C 361C 362C 398C 358 F1J1A1050021 CAPACITOR, 10V, 1µF 1C 363 F1J0J106A016 CAPACITOR, 6.3V, 10µF 6C 374C 426C 428C 663C 701C 384 F1G1C473A004 CAPACITOR, 16V, 0.047µF 6C 619C 627C 629C 630C 670C 386 F1G1A683A014 CAPACITOR, 10V, 0.068µF 1C 405 F1G1H470A451 CAPACITOR, 50V, 47pF 2C 406C 424 F1G1H8R0A452 CAPACITOR, 50V, 8pF 2C 425C 600 F1H1H104A731 CAPACITOR, 50V, 0.1µF 1C 602 F1G1H221A495 CAPACITOR, 50V, 220pF 7C 641C 646C 661

C 662C 675C 726C 603 F1H1H103A748 CAPACITOR, 50V, 0.01µF 2C 654C 604 F1L1E106A021 CAPACITOR, 25V, 10µF 7C 614C 623C 671C 687C 693C 714C 608 F1J1E105A009 CAPACITOR, 25V, 1µF 1C 610 F1J1E104A081 CAPACITOR, 25V, 0.1µF 1C 613 EEFUD0J101ER CAPACITOR, 6.3V, 100µF 2C 676C 615 F1H1H104A783 CAPACITOR, 50V, 0.1µF 16C 617C 622C 655C 658C 665C 682C 684C 691C 700C 705C 708C 709C 712C 724C 727C 618 F1K1E1060001 CAPACITOR, 25V, 10µF 7C 644C 645C 653C 672C 716C 717C 624 EEFUD0G151ER CAPACITOR, 4V, 150µF 2C 673C 639 F1G1H681A450 CAPACITOR, 50V, 680pF 1C 640 F1J1H334A533 CAPACITOR, 50V, 0.33µF 1C 656 F1H1H182A009 CAPACITOR, 50V, 1800pF 2C 668C 674 F1H1H472A748 CAPACITOR, 50V, 4700pF 1C 704 F1G1H152A450 CAPACITOR, 50V, 1500pF 1

CF 1 D4CC1103A038 THERMISTOR 1CN 2 K1MMH2B00003 CONNECTOR 1CN 3 K1KA02BA0014 CONNECTOR 2

CN 26CN 4 K1MN45AA0044 CONNECTOR 1CN 10 K1KA05BA0014 CONNECTOR 1CN 11 K1KB30AA0049 CONNECTOR 1CN 12 K1FB315BA003 CONNECTOR 1CN 13 K1NA09E00027 CONNECTOR 1CN 14 K1NA68E00096 CONNECTOR 1CN 15 K1MY26BA0001 CONNECTOR 1CN 16 K1KA08BA0014 CONNECTOR 1CN 18 K1KB12A00099 CONNECTOR 1CN 19 K1MMC4B00011 CONNECTOR 1CN 21 K1MN12BA0134 CONNECTOR 1CN 22 K1FY150BA007 CONNECTOR 1CN 23 K1KA20BA0114 CONNECTOR 1CN 25 K1MN60B00008 CONNECTOR 1CN 600 K1KA02B00247 CONNECTOR 1CN 601 K1KA10B00233 CONNECTOR 1

D 1 MA2J72900L DIODE 4D 2D 3D 8D 4 B0JDBE000002 DIODE 2D 641D 5 B0ADDH000004 DIODE 6D 6D 7D 600D 601D 603D 10 B3ABB0000164 DIODE 4D 11D 12D 13D 15 B3AKB0000008 DIODE 1D 16 B3ACB0000020 DIODE 2D 21D 19 B0JCMD000014 DIODE 8D 610D 612D 626D 628D 631D 632D 635D 20 B3ABB0000196 DIODE 1D 22 B0KB00000044 DIODE 2D 23D 602 MAZ81200ML DIODE 1D 604 MAZ81800ML DIODE 1D 605 B0JCCE000008 DIODE 3

D 624D 630D 606 MA3S132E0L DIODE 2D 622D 609 B0JCQD000001 DIODE 1D 611 B0JDAE000004 DIODE 2D 627D 613 MAZ80510ML DIODE 6D 614D 615D 617D 618D 640D 616 MAZ80620ML DIODE 1D 619 MA2S111-TX DIODE 2D 621D 620 B2ABAM000002 DIODE 1D 625 DEDRB081L20 DIODE 1D 629 B0JCPD000023 DIODE 3D 642D 643F 2 K5H2021A0003 FUSE, 2A 2F 3

IC 1 C2GBC0000263 IC, CPU 1IC 2 C1DB00001476 IC, CHIP SET 1IC 3 C1DB00001359 IC, CHIP SET 1IC 4 C3ABSY000001 IC, MEMORY 8IC 5IC 6IC 7IC 8IC 9IC 10IC 11IC 12 C0JBAZ002423 IC, CLOCK GENERATOR 1IC 14 C1ZBZ0002445 IC, PC-CARD SW 1IC 15 C0CBCBG00008 IC, REGULATOR 1IC 16 C1DB00001182 IC, LAN CONTROLLER 1IC 17 C3EBCG000100 IC, EEPROM 1IC 21 C0EBE0000460 IC 4IC 22IC 23IC 67IC 24 C0EBH0000457 IC 1IC 25 C0CBCBC00137 IC, REGULATOR 1IC 26 C2CBJA000003 IC, MICON 1IC 34 C0JBZZ000327 IC, THERMAL SENSOR 1IC 36 C3FBLC000040 IC, FLASH MEMORY 1IC 39 C0JBAB000619 IC, GATE LOGIC 1IC 40 C0JBAA000344 IC, GATE LOGIC 5

IC 50IC 52IC 77IC 614IC 41 C0JBAE000302 IC, LOGIC 3IC 46IC 49IC 42 C0JBAA000346 IC, LOGIC 4IC 43IC 73IC 74IC 44 C1DB00001439 IC, CARDBUS CONTROL 1IC 55 C0JBZZ000371 IC 2IC 57IC 56 C0DBZHG00043 IC, USB POWER CONTROL 2IC 59IC 60 C1DB00001221 IC, USB-ATAPI LSI 1IC 61 C1BB00001025 IC, AUDIO AMP 1IC 62 C0ABBA000093 IC, OP AMP 2IC 601IC 63 C0JBAB000616 IC, LOGIC 3IC 70IC 604IC 64 C0CBCBC00181 IC 1IC 65 C1BB00000868 IC, AC97 CODEC 1IC 66 C3EBEC000061 IC, EEPROM 1IC 69 C0CBCAC00183 IC, REGULATOR 1IC 71 C0JBAZ002422 IC, FET SWITCH 1IC 600 C0ABZA000047 IC, AMP 1IC 602 C0DBALH00003 IC 4IC 606IC 607IC 610IC 603 C0JBAD000182 IC, LOGIC 1IC 605 C0DBAFH00029 IC 1IC 608 C0DBEFH00002 IC, REGULATOR 1IC 609 C0EBE0000333 IC 1IC 613 C0DBDJH00009 IC, LINER 1JK 1 K2HC103B0090 JK 2JK 2

L 1 G1C100Z00013 INDUCTOR 2L 2L 3 G1C1R0Z00002 INDUCTOR 6L 4L 5L 7L 8L 55L 6 G1C91NM00001 INDUCTOR 1L 9 J0JJC0000015 INDUCTOR 1

L 10 J0JHC0000074 INDUCTOR 3L 13L 25L 23 J0MAB0000169 INDUCTOR 2L 24L 26 DDB5Z024E-L INDUCTOR 2L 54L 27 J0JCC0000186 INDUCTOR 7L 28L 29L 30L 31L 32L 33L 34 DDB5Z024C-L INDUCTOR 4L 35L 36L 37L 48 DDB5Z021C-Y INDUCTOR 6L 49L 50L 51L 52L 53L 600 DDB5Z028C-L INDUCTOR 1L 601 DDAZS100MT3T INDUCTOR 2L 602L 603 G1C1R6Z00001 INDUCTOR 1L 604 G1C4R7ZA0059 INDUCTOR 1L 605 G1C220MA0077 INDUCTOR 1L 607 G1C4R7MA0022 INDUCTOR 2L 608L 609 G1A160H00001 INDUCTOR 1

PS 1 K5J1BB000001 POLY SW 2PS 2

Q 1 UNR9214J0L TRANSISTOR 16Q 3Q 7Q 22Q 27Q 28Q 32Q 602Q 608Q 642Q 647Q 653Q 654Q 661Q 662

Q 663Q 4 B1DHDC000028 TRANSISTOR 9Q 8Q 10Q 13Q 17Q 19Q 624Q 625Q 668Q 5 B1CFGD000004 TRANSISTOR 7Q 6Q 628Q 630Q 644Q 648Q 657Q 9 XP0421300L TRANSISTOR 14Q 12Q 14Q 16Q 29Q 615Q 617Q 618Q 621Q 622Q 623Q 626Q 671Q 672Q 20 XP0421400L TRANSISTOR 3Q 21Q 600Q 23 B1GFCFEN0003 TRANSISTOR 1Q 24 DETA144EETL TRANSISTOR 3Q 33Q 664Q 31 UNR9111J0L TRANSISTOR 1Q 605 UNR9213J0L TRANSISTOR 4Q 606Q 620Q 659Q 607 B1DHFD000015 TRANSISTOR 2Q 666Q 609 B1CHRD000001 TRANSISTOR 2Q 610Q 611 B1DBGD000006 TRANSISTOR 6Q 613Q 632

Q 646Q 655Q 665Q 614 B1MBEDA00017 TRANSISTOR 3Q 636Q 638Q 619 B1DHFB000003 TRANSISTOR 2Q 667Q 629 B1ABCF000023 TRANSISTOR 2Q 631Q 633 B1DFGD000032 TRANSISTOR 1Q 637 B1CFGD000003 TRANSISTOR 2Q 660Q 645 B1DFED000020 TRANSISTOR 1Q 650 B1MBEDA00018 TRANSISTOR 1Q 674 B1CFMC000008 TRANSISTOR 1R 1 ERJ2GEJ681X RESISTOR, 1/16W, 680Ω 2R 252R 2 ERJ2RKF27R4X RESISTOR, 1/16W, 27.4Ω 3R 15R 16R 3 ERJ2GEJ151X RESISTOR, 1/16W, 150Ω 2R 6R 4 ERJ2RKF54R9X RESISTOR, 1/16W, 54.9Ω 6R 7R 17R 18R 35R 36R 5 ERJ2RKF39R2X RESISTOR, 1/16W, 39.2Ω 1R 11 ERJ3GEY0R00V RESISTOR, 1/16W, 0Ω 5R 240R 335R 336R 447R 12 ERJ2RKF2000X RESISTOR, 1/16W, 200Ω 2R 43R 13 ERJ2GEJ560X RESISTOR, 1/16W, 56Ω 6R 14R 27R 29R 31R 32R 23 ERJ3GEYJ100V RESISTOR, 1/16W, 10Ω 6R 679R 703R 734R 738R 780R 24 ERJ2RKF1001X RESISTOR, 1/16W, 1KΩ 1

R 25 ERJ2RKF2001X RESISTOR, 1/16W, 2KΩ 1R 26 ERJ2GEJ562X RESISTOR, 1/16W, 5.6KΩ 6R 312R 609R 613R 614R 752R 28 ERJ2GEJ750X RESISTOR, 1/16W, 75Ω 1R 33 ERJ2RKF2210X RESISTOR, 1/16W, 221Ω 2R 39R 34 ERJ2RKF1000X RESISTOR, 1/16W, 100Ω 3R 40R 42R 37 ERJ2RKF24R9X RESISTOR, 1/16W, 24.9Ω 4R 38R 66R 232R 41 ERJ2GE0R00X RESISTOR, 1/16W, 0Ω 65R 114R 115R 116R 117R 118R 119R 120R 121R 122R 123R 124R 125R 126R 127R 128R 129R 130R 131R 132R 133R 134R 135R 136R 137R 138R 139R 145R 147R 162R 167R 169R 224

R 229R 235R 236R 245R 246R 289R 297R 330R 355R 356R 366R 377R 379R 383R 384R 417R 432R 434R 436R 439R 442R 443R 477R 478R 479R 480R 604R 689R 693R 694R 784R 786R 47 ERJ2RKF80R6X RESISTOR, 1/16W, 80.6Ω 2R 48R 49 ERJ2GEJ103X RESISTOR, 1/16W, 10KΩ 62R 190R 191R 193R 198R 220R 221R 225R 230R 233R 241R 243R 247R 279R 293R 294

R 302R 307R 308R 315R 321R 322R 324R 325R 342R 353R 381R 382R 386R 387R 399R 400R 408R 412R 419R 420R 421R 423R 445R 446R 454R 457R 459R 463R 471R 616R 684R 697R 698R 705R 710R 711R 717R 719R 722R 728R 730R 731R 746R 747R 776R 781R 50 ERJ2GEJ222X RESISTOR, 1/16W, 2.2KΩ 8R 51R 280R 281

R 285R 286R 340R 341R 52 ERJ2GEJ101X RESISTOR, 1/16W, 100Ω 25R 203R 226R 228R 242R 259R 288R 290R 309R 319R 362R 365R 401R 402R 418R 449R 617R 618R 651R 652R 653R 654R 655R 656R 788R 53 ERJ2RKF1002X RESISTOR, 1/16W, 10KΩ 1R 54 ERJ2RKF75R0X RESISTOR, 1/16W, 75Ω 3R 55R 56R 57 D1H82224A024 RESISTOR ARRAY 1R 58 ERJ2RKF1501X RESISTOR, 1/16W, 1.5KΩ 2R 462R 63 ERJ2GEJ390X RESISTOR, 1/16W, 39Ω 2R 64R 65 ERJ2RKF2550X RESISTOR, 1/16W, 255Ω 1R 67 ERJ6GEYJ100V RESISTOR, 1/10W, 10Ω 1R 68 ERJ2GEJ201X RESISTOR, 1/16W, 200Ω 4R 70R 72R 74R 80 D1HG2208A001 RESISTOR ARRAY 8R 81R 82R 83R 108R 109

R 110R 111R 84 ERJ2GEJ220X RESISTOR, 1/16W, 22Ω 27R 85R 86R 87R 88R 89R 90R 91R 92R 93R 94R 95R 96R 97R 98R 99R 100R 101R 102R 103R 104R 105R 106R 107R 350R 351R 444R 112 D1HA56080001 RESISTOR ARRAY 7R 113R 140R 141R 142R 143R 144R 149 ERJ2GEJ102X RESISTOR, 1/16W, 1KΩ 12R 150R 151R 152R 267R 300R 339R 354R 425R 474R 475R 677R 153 ERJ3GEYJ2R2V RESISTOR, 1/16W, 2.2Ω 2R 176

R 154 ERJ2RKF49R9X RESISTOR, 1/16W, 49.9Ω 16R 155R 156R 157R 158R 159R 194R 195R 196R 197R 295R 313R 314R 316R 317R 404R 160 ERJ2GEJ120X RESISTOR, 1/16W, 12Ω 4R 161R 185R 409R 166 ERJ2GEJ330X RESISTOR, 1/16W, 33Ω 19R 178R 179R 181R 182R 183R 186R 187R 188R 189R 219R 265R 266R 270R 271R 407R 464R 465R 468R 170 D1H83304A024 RESISTOR ARRAY 1R 175 ERJ2RKF4750X RESISTOR, 1/16W, 475Ω 1R 177 ERJ3GEYJ1R0V RESISTOR, 1/16W, 1Ω 3R 248R 685R 192 ERJ2GEJ104X RESISTOR, 1/16W, 100KΩ 35R 217R 222R 276R 277R 278

R 287R 291R 296R 299R 305R 329R 346R 358R 363R 369R 371R 375R 388R 395R 396R 413R 415R 612R 621R 622R 628R 629R 646R 649R 650R 690R 745R 789R 795R 218 D1H81034A024 RESISTOR ARRAY 9R 223R 256R 301R 333R 359R 410R 431R 473R 231 ERJ2RKF22R6X RESISTOR, 1/16W, 22.6Ω 1R 237 ERJ2GEJ203X RESISTOR, 1/16W, 20KΩ 1R 238 ERJ2GEJ106X RESISTOR, 1/16W, 10MΩ 1R 239 ERJ2GEJ105X RESISTOR, 1/16W, 1MΩ 10R 318R 348R 349R 619R 627R 647R 678R 683

R 790R 249 ERJ3GEYJ121V RESISTOR, 1/16W, 120Ω 2R 250R 253 DEARA8AJ103M RESISTOR ARRAY 6R 254R 255R 304R 389R 458R 258 ERJ2GEJ473X RESISTOR, 1/16W, 47KΩ 12R 261R 263R 264R 303R 344R 368R 448R 623R 661R 687R 773R 268 J0JAC0000021 FILTER 2R 269R 272 ERJ2GEJ472X RESISTOR, 1/16W, 4.7KΩ 6R 441R 451R 472R 686R 756R 298 ERJ2GEJ100X RESISTOR, 1/16W, 10Ω 15R 663R 664R 701R 702R 706R 707R 714R 715R 723R 727R 732R 736R 777R 778R 311 ERJ2RHD562X RESISTOR, 1/16W, 5.6KΩ 1R 331 ERJ2GEJ223X RESISTOR, 1/16W, 22KΩ 2R 657R 338 ERJ2GEJ153X RESISTOR, 1/16W, 15KΩ 6R 440R 704

R 716R 739R 775R 306 ERJ2GEJ334X RESISTOR, 1/16W, 330KΩ 2R 372R 320 EXBV8V750JV RESISTOR　ARRAY 1R 323 ERJ2GEJ333X RESISTOR, 1/16W, 33KΩ 3R 334R 343R 326 ERJ2GEJ363X RESISTOR, 1/16W, 36KΩ 3R 327R 328R 347 ERJ2GEJ471X RESISTOR, 1/16W, 470Ω 2R 397R 380 ERJ2RKF3901X RESISTOR, 1/16W, 3.9KΩ 1R 385 ERJ2RHD103X RESISTOR, 1/16W, 10KΩ 3R 608R 611R 390 ERJ2GEJ561X RESISTOR, 1/16W, 560Ω 2R 391R 392 ERJ3GEYJ151V RESISTOR, 1/16W, 150Ω 2R 393R 394 ERJ2GEJ391X RESISTOR, 1/16W, 390Ω 1R 398 ERJ2GEJ470X RESISTOR, 1/16W, 47Ω 2R 452R 403 ERJ6GEYJ101V RESISTOR, 1/10W, 100Ω 2R 450R 453 ERJ2RKF39R0X RESISTOR, 1/16W, 39Ω 2R 461R 456 ERJ2RKF2431X RESISTOR, 1/16W, 2.43KΩ 1R 466 ERJ6GEY0R00V RESISTOR, 1/10W, 0KΩ 1R 600 ERJ2RHD104X RESISTOR, 1/16W, 100KΩ 2R 603R 601 ERJ2RKD154X RESISTOR, 1/16W, 150KΩ 2R 602R 605 D1ZZ00000046 RESISTOR, 1W, 5mΩ 2R 692R 606 ERJ3GEYJ562V RESISTOR, 1/16W, 5.6KΩ 1R 610 RL1220SR47F RESISTOR, 1/8W, 0.47Ω 1R 615 ERJ2GEJ474X RESISTOR, 1/16W, 470KΩ 4R 744R 754R 774R 620 ERJ3GEYJ3R3V RESISTOR, 1/16W, 3.3Ω 1R 624 RL1220SR15F RESISTOR, 1/8W, 0.15Ω 3R 625R 626R 630 D1BDR0220001 RESISTOR, 1/8W, 0.022Ω 7R 631R 695

R 696R 725R 726R 743R 632 ERA3YKB104V RESISTOR, 1/16W, 100KΩ 3R 751R 762R 633 ERA3YEB203V RESISTOR, 1/16W, 20KΩ 2R 740R 639 ERA3YEB103V RESISTOR, 1/16W, 10KΩ 1R 640 ERA3YEB303V RESISTOR, 1/16W, 30KΩ 1R 641 D1BDR0330001 RESISTOR, 1/8W, 0.033Ω 3R 642R 741R 644 ERJ2GEJ684X RESISTOR, 1/16W, 680KΩ 1R 648 ERJ2GEJ225X RESISTOR, 1/16W, 2.2MΩ 1R 658 ERJ6GEYJ561V RESISTOR, 1/10W, 560Ω 1R 659 ERJ6GEYJ222V RESISTOR, 1/10W, 2.2KΩ 2R 660R 665 ERJ2RKF1004X RESISTOR, 1/16W, 1MΩ 2R 671R 666 ERJ2RHD223X RESISTOR, 1/16W, 22KΩ 1R 667 ERJ2RHD333X RESISTOR, 1/16W, 33KΩ 1R 668 ERJ2RKF1003X RESISTOR, 1/16W, 100KΩ 2R 676R 669 ERJ2RHD222X RESISTOR, 1/16W, 2.2KΩ 1R 670 ERJ2RKF5102X RESISTOR, 1/16W, 51KΩ 2R 712R 672 ERJ2RHD133X RESISTOR, 1/16W, 13KΩ 1R 674 ERJ2RHD123X RESISTOR, 1/16W, 12KΩ 2R 724R 680 ERJ2GEJ154X RESISTOR, 1/16W, 150KΩ 2R 688R 681 ERJ2GEJ513X RESISTOR, 1/16W, 51KΩ 1R 682 ERJ2GEJ302X RESISTOR, 1/16W, 3KΩ 1R 708 ERJ2RKF4701X RESISTOR, 1/16W, 4.7KΩ 1R 709 ERJ2RKF1502X RESISTOR, 1/16W, 15KΩ 2R 733R 713 ERJ2RKF2402X RESISTOR, 1/16W, 24KΩ 1R 720 D1BDR0470002 RESISTOR, 1/8W, 0.047Ω 1R 729 ERA3YEB622V RESISTOR, 1/16W, 6.2KΩ 1R 735 ERJ2GEJ221X RESISTOR, 1/16W, 220Ω 1R 737 ERA3YEB471V RESISTOR, 1/16W, 470Ω 1R 742 ERA3YEB243V RESISTOR, 1/16W, 24KΩ 1R 748 ERJ2RKD114X RESISTOR, 1/16W, 110KΩ 1R 749 ERJ2RKF1503X RESISTOR, 1/16W, 150KΩ 1R 750 ERJ2RHD3652X RESISTOR, 1/16W, 36.5KΩ 1R 757 ERJ2RHD302X RESISTOR, 1/16W, 3KΩ 2R 758R 759 D1BDR0680001 RESISTOR, 1/8W, 0.068Ω 2

R 760R 763 ERA3YEB333V RESISTOR, 1/16W, 33KΩ 1R 768 ERJ2RHD132X RESISTOR, 1/16W, 1.3KΩ 1R 769 ERJ2RKF1102X RESISTOR, 1/16W, 11KΩ 2R 772R 771 ERJ2RKF1302X RESISTOR, 1/16W, 13KΩ 1R 779 ERA3YEB621V RESISTOR, 1/16W, 620Ω 1R 793 ERJ1TYJ201U RESISTOR, 1W, 200Ω 2R 794

SW 5 K0ZZ00000617 SW 1SW 6 ESD165225 SW 1SW 7 K0D112B00071 SW 1SW 8 EVQPLDA15 SW 2SW 9

T 1 G5BYC0000010 TRANCE 1X 1 H0J143500058 OSCILLATOR, 14.318MHz 1X 2 H0J327200141 OSCILLATOR, 32.768KHz 1X 3 H0J250500025 OSCILLATOR, 25MHz 1X 4 H2D800400015 OSCILLATOR, 8MHz 1X 5 H0J300500011 OSCILLATOR, 30MHz 1

ZA 1 DRHM0100ZA SPACER 1ZA 2 DRHM0099ZA SPACER 1

USB PCBC 901 EEFUD0J151ER CAPACITOR, 6.3V, 150µF 2C 902

CN 901 K1KA12BA0014 CONNECTOR 1CN 902 K1FB104B0055 CONNECTOR 2CN 903

D 901 B0KB00000044 DIODE 2D 902L 901 J0MAB0000116 INDUCTOR 2L 902L 903 J0JHC0000074 INDUCTOR 4L 904L 905L 906

SW PCBC 951 F1G1A104A014 CAPACITOR, 10V, 0.1µF 2C 952C 953 F1G1E103A062 CAPACITOR, 25V, 0.01µF 1

CN 952 K1KA02BA0181 CONNECTOR 1CN 951 K1MY20BA0002 CONNECTOR 1

D 951 B3ABB0000196 DIODE 1D 952 MA2S111-TX DIODE 1

IC 951 C0EBE0000460 IC 1Q 952 B1DHFB000003 TRANSISTOR 1Q 951 UNR9214J0L TRANSISTOR 1R 952 ERJ2GEJ104X RESISTOR, 1/16W, 100KΩ 1R 951 ERJ3GEYJ101V RESISTOR, 1/16W, 100Ω 1R 953 ERJ6GEY0R00V RESISTOR, 1/10W, 0Ω 1

SW 951 K0D113B00081 SW 1SW 952 K0L1BA000115 SW 2SW 953