PERSONAL CAREFormulation guide

Quatin®

Betafib®

MCF

Explore our portfolio:

Rinse-off Leave-on

SHAMPOOPhase Ingredient INCI %

1 Water Aqua q.s. 100

LES28 Sodium Laureth Sulfate 24.00

Euroquat HCB LA Cocamidopropyl Betaine 12.00

Euxyl K712 Aqua (and) Sodium Benzoate (and) Potassium Sorbate 1.25

Quatin® 680 TQ D Hydroxypropyltrimonium Inulin 1.25

Citric acid (10% solution) Citric Acid q.s.

Sodium Chloride Sodium Chloride q.s.

Production method

1. Introduce the ingredients in the order listed above, taking care to homogenize properly after each introduction.

2. Use citric acid to adjust pH to the target pH of 5,5.3. Add Sodium Chloride in order to adjust viscosity.

NIGHT CREAMPhase Ingredient INCI %

A Water Water 74.24

Betafib® (0,8%) Cellulose 2.43

Glycerin Glycerin 3.00

B Sunflower oil Helianthus Annuus (Sunflower) Seed Oil 16.68

C Emulgin SG Sodium Stearoyl Glutamate 0.50

D Emulgade PL 68/50 Cetearyl Glucoside (and) Cetearyl Alcohol 3.00

Glydant plus DMDM Hydantoin (and) Iodopropynyl Butylcarbamate 0.15

E Citric acid Citric acid 74.24

Production method

1. Mix A with high shear mixer (silverson )with a hole high shear screen for 20 minutes at 8000 rpm.

2. In the meantime heat B to 70 ºC low shear.3. Add C very slow to B at 70 ºC low shear.4. Add A together with B and C and mix with high shear (silverson)

with a emulsion screen for 3 minutes at 8000 rpm.

5. Cool the emulsion down while stirring at 800 rpm for 25 minutes.

6. Add D to the emulsion and stirr for 1 minute at 800 rpm.7. Bring the pH to 6 with E while stirring at 800 rpm.8. Degass the emulsion in a vacuumoven at roomtemperature

overnight at 115 bar.

1. Disperse Betafib® in water of (1) and shear with high shear mixer for 20 minutes. Then add other ingredients of (1).

2. Add (2) to (1) and heat to 85°C.3. Heat (3) to 85°C4. Add (3) to (1+2) while homogenising with a high shear mixer

for 3 minutes.

5. Cool down to 20°C while stirring slowly. Then add ingredients of (4).

6. Whip emulsion with a Hobart (batch aeration equipment) until a density of 0.5 is reached.

BODY MOUSSEPhase Ingredient INCI %

1 Deionised water Aqua 68.47

Glycerin (99%) Glycerin 5

Betafib® Cellulose 0.75

2 Brown Color CI 14700, CI 19140, CI 17200, Sodium Sulfate 0.025

Sisterna SP70-C Sucrose Stearate 1.5

Sisterna SP30-C Sucrose Distearate 1.5

Kelcogel CG-HA Gellan Gum 0.15

3 Lipex Cocoasoft Theobroma Cacao (Cocoa) Seed Butter 15.5

Sunflower oil Helianthus Annuus (Sunflower) Seed oil 4

CSA 50/50 Cetearyl Alcohol 0.5

4 Euxyl PE9010 Phenoxyethanol, Ethylhexylglycerin 1

Vitamin E Acetate Tocopheryl Acetate 0.1

Orange Cream (342283) Parfum 0.15

Production method

1. Introduce the ingredients in the order listed above, taking care to homogenize properly after each introduction.

2. Adjust pH<6,3 for viscosity build up and clarity.

HAND SANITIZERPhase Ingredient INCI %

1 Water Aqua 31.60

Ethanol Alcohol 62.00

Quatin® 350 TQ D Hydroxypropyltrimonium Inulin 1.25

Euroflow 100 Acrylates/Beheneth-25 Methacrylate Copolymer 6.40

2 Sodium Hydroxide (10 w/w%) Sodium Hydroxide q.s.

Production method

1. Mix A with high shear mixer (silverson) with a hole high shear screen for 20 minutes at 8000 rpm.

2. Heat A to 70 ºC while stirring at low shear.3. Disperse B heat up till 70 ºC while stirring at low shear.4. Disperse C heat up till 70 ºC while stirring at low shear.

Add TiO2 at 70 ºC5. Add A and B together and high shear (silverson) with emulsion

screen for 1 minute at 8000 rpm.

6. Add C to (A+B) and homogenise high shear (silverson) with emulsion screen for 15 minutes at 5000 rpm.

7. Cool down to 35 ºC under low shear.8. Add D to the emulsion with low shear for 1 minute.9. Bring the pH to 6 with E while stirring at 800 rpm, after this

stir for another 15 minutes low shear.10. If necessary degass the emulsion in a vacuumoven at

roomtemperature overnight at 115 bar.

SUN SCREEN CREAMPhase Ingredient INCI %

A Demi water Water 61.16

Betafib® Cellulose 3.17

B Glycerin Glycerin 5

CETIOL AB C12-15 Alkyl Benzoate 6

Eumulgin SG Sodium Stearoyl Glutamate 0.5

Emulgade PL 68/50 Cetearyl Glucoside (and) Cetearyl Alcohol 3

C LUVITOL EHO Cetearyl Ethylhexanoate 2

Natura-Tec Ultrafeel ISIS 10-15 Isostearyl Isostearate 4

Eusolex 9020 Butyl Methoxydibenzoylmethane 2

Aakosun OCR Octocrylene 8

D Glydant plus liquid DMDM Hydantoin (and) Iodopropynyl Butylcarbamate 0.12

Dermofeel Toco 70 non GMO Tocopherol (and) Helianthus Annuus (Sunflower) Seed Oil 0.05

E Acid or base q.s.

Production method

Contact

Cosun Biobased ProductsP.O. Box 204670 AA DinteloordThe NetherlandsT +31 76 530 3333

Where are we based?

Sales officesThe NetherlandsKreekweg 14671 VA DinteloordT +31 76 530 3333

United States of AmericaP.O. Box 641955San Jose, CA 95164T +1 408 455 5672

Production locationThe NetherlandsBorchwerf 34704 RG RoosendaalT +31 76 530 3333

For more information

Visit our website:www.cosunbiobased.com

Or email us: biobasedproducts@cosun.com

The information and recommendations in this leaflet are to the best of our knowledge, information and belief accurate at the date of publication. Nothing herein is to be construed as warranty expressed or implied. In all cases it is the responsibility of users to determine the applicability of such information or the suitability of any products for their own particular purpose.

Formulation Guide

20

18

-09

BODY LOTION

Phase INGREDIENT INCI %

1 Water Water 68.830

Betafib® (21,2%) Cellulose 1.42

Avicel PC611 Microcrystalline cellulose 1.50

2 Sisterna SP30-30 Sucrose stearate 3.00

Sisterna SP70-C Sucrose stearate 1.00

Squalane Squalane 18.00

3 Euxyl K712 Aqua (and) Sodium Benzoate (and) Potassium Sorbate 1.25

Quatin® 350 TQ-D Hydroxypropyltrimonium Inulin 1.00

Glycerin 86% Glycerin 4.00

4 Citric Acid (20% solution) Citric acid q.s.

Production method

1. Disperse Avicel PC611 in the water of (1) and shear for 10 minutes with Ultra Turrax at 6000 rpm

2. Add Betafib and shear for 10 minutes with Ultra Turrax at 8500 rpm. Heat the mixture to 70°C.

3. Heat (2) to 70°C. Add (2) to (1) while homogenizing for 3 minutes.

4. Cool down to 35°C while slowly stirring, add (3).

5. Homogenise for 10-15 minutes.6. Cool down to roomtemperature.7. Adjust pH if necessary with (4).