performance test data sealed spherical roller bearings · · 2016-03-22ultage sealed spherical...
TRANSCRIPT
1. Because the internal radial clearance of “ULTAGE Series Sealed Spherical Roller Bearings” with tapered bores cannot be measured with a thickness gauge, please monitor clearances by measuring the axial movement of the inner ring as shown in Table 1.
2. During assembly, if misalignment exceeding the allowable misalignment angle of ±0.5˚ is applied to the bearing, rollers may come in direct contact with seals causing seal deformation. Furthermore, if additional force is applied under these conditions, seals may separate from the bearing entirely. Therefore, caution is advised.
3. Please use Lithium mineral grease. In case other types of grease are to be used, please consult NTN.
4. If a shrink fit is to be applied, please do not exceed a bearing temperature of 100˚C. However, these bearing cannot be shrink fit via immersion in a hot oil bath.
Rotational speed min-1
Out
er ri
ng te
mpe
ratu
re ri
se ˚
C
Rot
atio
nal t
orqu
e N・
mm
00.0
20.0
40.0
60.0
80.0
100.0
200 400 600 800 1000 1200 1400 1600Rotational speed min-1
00
50
100
150
200
200 400 600 800 1000 1200 1400 1600
Performance Test Data
Handling Precautions
ULTAGE Sealed Spherical Roller Bearings [ WA Type ]
●Heat Run Test
[Test conditions] Bearing :WA22218EALLSD1 Load :Radial load 294N{30kgf} Speed :200~1400min-1
Lubrication :Shell Alvania EP grease No.2 (NTN code 8A) Amount of grease :20% of free space Operating time :Until temperature rise stabilizes
●Noise Test
[Test conditions] Bearing :WA22218EALLSD1 Load :Radial load 980N{100kgf} Speed :600, 900, 1200min-1
Lubrication :Shell Alvania EP grease No.2 (NTN code 8A) Amount of grease :20% of free space
●Grease Leakage Test
[Test conditions] Bearing :WA22218EALLSD1 Load :Radial load 1960N{200kgf} Speed :1000min-1
Lubrication :Shell Alvania EP grease No.2 (NTN code 8A) Amount of grease :20% of free space Operating time :100 hours
[Test results] [Test results]
[Test results]
Outer ring temperature rise Rotational torque
24
30
40
50
65
80
100
120
30
40
50
65
80
100
120
130
0.010
0.010
0.015
0.025
0.035
0.035
0.050
0.060
0.015
0.015
0.020
0.030
0.040
0.045
0.060
0.070
Nominal borediameter
Axialdisplacement
drive-up
Minimum residualinternal clearance
Reduction inradial internal
clearance
Table 1 Installing sealed tapered bore bearings
mmd
over incl. min max
0.15
0.20
0.30
0.35
0.45
0.60
0.75
0.85
0.20
0.25
0.35
0.40
0.55
0.70
0.85
0.95
min max
0.015
0.020
0.025
0.025
0.030
0.035
0.040
0.050
0.025
0.035
0.040
0.045
0.055
0.065
0.075
0.090
CN C3
0.040
0.050
0.060
0.065
0.080
0.095
0.110
0.130
C4
600
900
1200
Noize level dBA
min-1 50 60 70 80
[Test results]Accumulated total amount
of grease leakage
25h
0.47g
50h
0.58g
100h
0.63g
Rotationalspeed
HEADQUARTERSNTN Corporation URL http://www.ntn.co.jp1-3-17, Kyomachibori, Nishi-ku, Osaka-shi, Osaka 550-0003 Japan Phone: +81-6-6443-5001
NTN USA Corporation URL http://www.ntnamerica.com1600 E. Bishop Court, P.O. Box 7604, Mount Prospect, IL 60056-7604, U.S.A. Phone: +1-847-298-7500 Fax: +1-847-294-1209
SALES NETWORKNTN Bearing Corp. of AmericaHead Office / 1600 E. Bishop Court, P.O. Box 7604, Mount Prospect, IL 60056-7604, U.S.A. Phone: +1-847-298-7500 Fax: +1-847-699-9744Central Sales Office / 2413 North Main Street, East Peoria, Illinois 61611 Phone: +1-309-699-8600 Fax: +1-309-699-8670NTN Automotive Center / 39255 W. 12 Mile Road, Farmington Hills, MI 48331-2975, U.S.A. Phone: +1-248-324-4700 Fax: +1-248-324-1103
NTN Bearing Corp. of Canada Ltd. URL http://www.ntn.caHead Office / 305 Courtneypark Drive West, Mississauga, Ontario, L5W 1Y4, Canada Phone: +1-905-564-2700 Fax: +1-905-564-7749Vancouver Branch / 106B - 3680 Bonneville Place Burnaby, B.C. V3N 4T6, Canada Phone: +1-604-444-2007 Fax: +1-604-444-2665Edmonton Branch / 4608-97th Street, Edmonton, Alberta T6E 5N9, Canada Phone: +1-780-435-6200 Fax: +1-780-435-3600Toronto Branch / 305 Courtneypark Drive West, Mississauga, Ontario L5W 1Y4, Canada Phone: +1-905-564-9600 Fax: +1-905-564-9609Montreal Branch / 4973 Levy Street, Ville, St-Laurent, Quebec, H4R 2N9, Canada Phone: +1-514-333-8054 Fax: +1-514-333-1078
NTN Wälzlager (Europa) GmbH. URL http://www.ntn-snr.comHead Office / Max-Planck-Str. 23, 40699 Erkrath, F.R.Germany Phone: +49-211-2508-0 Fax: +49-211-2508-400Stuttgart Branch / Plieninger Str. 63B, 70794 Filderstadt F.R.Germany Phone: +49-711-123901-0 Fax: +49-711-123901-660
NTN Bearings (UK) Ltd. URL http://www.ntn-snr.comWellington Crescent, Fradley Park, Lichfield, Staffordshire, WS13 8RZ, U.K. Phone: +44-1543-445000 Fax: +44-1543-445035
NTN-SNR ROULEMENTS. URL http://www.ntn-snr.comHead Office / 1, rue des Usines B.P. 2017 74010 Annecy Cedex, France Phone: +33-4-50-65-30-00 Fax: +33-4-50-65-32-91Lyon Branch / 51, rue des Docks, 69009 Lyon, France Phone: +33-4-78-66-68-00 Fax: +33-4-78-66-68-20Paris Branch / 6, rue Auguste Comte, BP49, 92174 Vanves Cedex, France Phone: +33-1-40-93-66-00 Fax: +33-1-40-93-66-10Cran Gevrier Branch / 6 route de la Salle, 74960, Cran Gevrier, France Phone: +33-4-50-65-93-00 Fax: +33-4-50-65-93-46Haguenau Branch / 4, rue de la Sablière, BP30338, 67507 Haguenau Cedex, France Phone: +33-3-88-53-22-22 Fax: +33-3-88-73-46-95Argonay Branch / 114, Rte de Champ Farçon, 74370, Argonay, France Phone: +33-4-50-65-94-00 Fax: +33-4-50-65-94-25
SNR Wälzlager GmbH. Head Office / Max-Planck-Str. 23, 40699 Erkrath, F.R.Germany Phone: +49-211-2508-0 Fax: +49-211-2508-400 Bielefeld Branch / Friedrich-Hagemann-Straße 66, 33719 Bielefeld, F.R.Germany Phone: +49-521-9-24-00-0 Fax: +49-521-9-24-00-90 Stuttgart Branch / Plieninger Str. 63B, 70794 Filderstadt F.R.Germany Phone: +49-711-123901-0 Fax: +49-711-123901-660
NTN-SNR ITALIA S.P.A. / Via Riccardo Lombardi, 19/4, 20153 Milan, Italy Phone: +39-02-47-99-86-00 Fax: +39-02-33-50-06-56NTN-SNR IBERICA SA / Calle Barberán n˚6, 28035 Madrid, Spain Phone: +34-916-71-89-13 Fax: +34-916-73-65-48NTN-SNR RULMENTI S.R.L. / Zona Industriala-Vest, 6 Strada Salzburg, 24 00 SIBIU, Romania Phone: +40-269-20-35-00 Fax: +40-269-20-35-25NTN-SNR Marocco / Route cotiere 111, Quartier industriel, Polygone 1, Casablanca, Morocco Phone: +212-522-66-76-80 Fax: +212-522-66-5166
NTN Bearing-Singapore (Pte) Ltd. URL http://www.ntn.com.sgHead Office / No.9 Clementi Loop Singapore 129812 Phone: + 65-64698066 Fax: +65-64695400Philippine Representative Office / Unit 1002 Philippine Axa Life Centre Condominium Corporation Sen. Gil Puyat Ave Corner Tindalo Street Makati City, Philippines Phone: +63-2-759-4407 Fax: +63-2-759-4409Vietnam Representative Office / 303, 3rd of Thanh Dong Building 132 - 138 Kim Ma Str., Ba Dinh Dist., Ha Noi, Viet Nam Phone: +84-4-37347661 Fax: +84-4-37347662
NTN Bearing India PVT. Ltd.Head Office / SPIC Annexe Building, 2nd Floor No.86, Mount Road, Guindy Chennai 600032, India Phone: +91-0-44-33707700 Fax: +91-0-44-33707701Delhi Branch / 715-716, International Trade Tower, Nehru Place, New Delhi - 1100019, India Phone: +91-0-11-40520406 Fax: +91-0-11-40520407
NTN (China) Investment Corp. URL http://www.ntn.com.cnShanghai Head Office / No.6 building No.1666 Nanle Road, Songjiang Industrial Zone, Songjiang, Shanghai 201611, China Phone: +86-21-5774-5500 Fax: +86-21-5778-2898Beijing Branch / Unit 3018, South Tower, Beijing Kerry Centre, 1 Guanghua Road, Chaoyang District, Beijing 100020, China Phone: +86-10-6568-3069 Fax: +86-10-6568-2278Guangzhou Branch / Room 3606, Onelink Center, No.230-232 Tianhe Road, Tianhe District, Guangzhou 510620, China Phone: +86-20-3877-2943 Fax: +86-20-3877-2942Nanjing Branch / Room 18A, Nanjing IFC, No.1 Hanzhong Rd, Baixia District, Nanjing 210029, China Phone: +86-25-8477-5355 Fax: +86-25-8477-5360Chongqing Branch / Room 15-6, Carnival mansion, No.9 Guanyingqiao Street, Jiangbei District, Chongqing 400020, China Phone: +86-23-6796-0812 Fax: +86-23-6796-0878Shenyang Branch / Room 2606, China Resources Building, No.286 Qingnian Street, Heping District, Shenyang 110004, China Phone: +86-24-3137-9186 Fax: +86-24-3137-9185
NTN China Ltd. URL http://www.ntnchina.comHong Kong Office / Room 1914-15, Park-In Commercial Centre, 56 Dundas Street, Mongkok, Kowloon, Hong Kong Phone: +852-2385-5097 Fax: +852-2385-2138
NTN Bearing-Thailand Co., Ltd.Head Office / 12th Floor, Panjathani Tower, 127/15 Nonsee Road, Chongnonsee Yannawa, Bangkok 10120, Thailand Phone: +66-2-681-0401 Fax: +66-2-681-0408Khon Kaen Branch / 189-191 Ruen Rom Road Tambon Nai-Muang, Amphur Muang, Kohn Kaen, 40000, Thailand Phone: +66-43-223679 Fax: +66-43-223061Haad Yai Branch / 198-198/1 Nipat U-Thid 2 Road, Amphur Haad Yai, Songkhla, 90110, Thailand Phone: +66-74-236568 Fax: +66-74-231520Bangna Branch / 35/35 Bangna-Trad Road, KM11 Bangplee, Samutprakarn, 10540, Thailand Phone: +66-2-7501732 Fax: +66-2-7501731Chiangmai Branch / 208 (Room B3-B4)Moo4 2nd, Ring Road, T.Nong Hoi, A.Muang, Chiangmai 50000, Thailand Phone: +66-53-874328 Fax: +66-53-874330
NTN Bearing-Malaysia Sdn. Bhd.Head Office / No.2, Jalan Arkitek U 1/22, Hicom Glenmarie Industrial Park, 40150 Shah Alam, Selangor, Malaysia Phone: +60-3-55696088 Fax: +60-3-55690200Butterworth Branch / 4700, Jalan Permatang Pauh, 13400 Butterworth, Malaysia Phone: +60-4-3328312 Fax: +60-4-3324407Ipoh Branch Office /65, Medan Kidd, Kinta Mansion, 30200 Ipoh, Malaysia Phone: +60-5-2547743 Fax: +60-5-2538077Kuantan Branch / B-72, Ground Floor, Jalan Beserah 25300 Kuantan, Malaysia Phone: +60-9-5141132 Fax: +60-9-5141164Johor Bahru Branch / 51 Jalan, Sri Bahagia 5, Taman Sri Bahagia, Tampoi, 81200 Johor Bahru, Malaysia Phone: +60-7-2364929 Fax: +60-7-2370897
PT. NTN Bearing IndonesiaC-21, 22 MM2100 Industrial Town, Cikarang Barat, BEKASI 17520 West Jave Indonesia Phone : +62-21-89983827 Fax : +62-21-89983831
NTN-CBC (Australia) Pty. Ltd.3, The Crescent, Kingsgrove, NSW 2008, Australia Phone: +61-2-99479200 Fax: +61-2-95543311
NTN de Mexico, S.A. URL http://www.ntnmexico.com.mxMexico Head Office / Emilio Cárdenas No.158 Apdo.124, C.P.54030, Tlalnepantla, Edo.deMéxico, Mexico Phone: +52-55-5390-1133 Fax: +52-55-5565-8545Guadalajara Branch / Calle 22 No.2465, Zona Industrial, C.P.44940, Guadalajara, Jalisco, Mexico Phone: +52-33-3145-1448 Fax: +52-33-3145-1594Monterrey Branch / Av. Ruiz Cortines No.1336 Ote, Col. La Purisima, C.P.67120, Cd. Guadalupe, Nuevo Leon, Mexico Phone: +52-818-334-9931 Fax: +52-818-334-9932Mexicali Branch / Blvd. Benito Juárez No.3293 Esq. Ayuntamiento, C.P.21360, Mexicali, BCN, Mexico Phone: +52-686-563-3632 Fax: +52-686-582-2057
NTN Sudamericana, S.A. URL http://www.ntnsudamericana.comWorld Trade Center Panama Calle 53 Este, Urbanización Marbella Piso NO.16, Oficina 1601 Apartado Postal 832-0487, Panamá, Rep.de Panamá Phone: +507-269-4777 Fax: +507-264-5592
NTN do Brasil Ltda. URL http://www.ntn.com.brAv. Moema, 94-9˚ Andar-conj, 92a94 CEP 04077-020-Indianópolis-São Paulo-SP, -Brasil Phone: +55-11-5051-0600 Fax: +55-11-5051-2807
NTN Korea Co., Ltd.Head Office / 10th Floor, Press Center, 25, Taepyeong-Ro 1-GA, Jung-Gu, Seoul 100-745, Korea Phone: +82-2-720-3666 Fax: +82-2-720-3669Busan Branch / Rm.707, 7th Floor, Daerim Bldg., 341-5 Bujeon 1-Dong, Busanjin- Gu, Busan, 614-843, Korea Phone: +82-51-811-1351 Fax: +82-51-811-1353
NOTE : The appearance and specifications may be changed without prior notice if required to improve performance. Although care has been taken to assure the accuracy of the data compiled in this catalog, NTN does not assume any liability to any company or person for errors or omissions.
AE74 CAT. No. 3703/E 13. 07. 03. N Printed in Japan
Sealed Spherical Roller Bearings[WA Type]
CAT. No. 3703/ENote: Markings on the seal are not white in actual bearings.
**自動調心ころWA_E_**自動調心ころWA 13/07/16 13:43 ページ 2
WA22205EALLSW33
WA22206EALLSW33
WA22207EALLSW33
WA22208EALLSD1
WA22209EALLSD1
WA22210EALLSD1
WA22211EALLSD1
WA22212EALLSD1
WA22213EALLSD1
WA22214EALLSD1
WA22215EALLSD1
WA22216EALLSD1
WA22217EALLSD1
WA22218EALLSD1
WA22220EALLSD1
WA22222EALLSD1
WA22224EALLSD1
WA22226EALLSD1
WA22207EALLSKW33
WA22208EALLSKD1
WA22209EALLSKD1
WA22210EALLSKD1
WA22211EALLSKD1
WA22212EALLSKD1
WA22213EALLSKD1
WA22214EALLSKD1
WA22215EALLSKD1
WA22216EALLSKD1
WA22217EALLSKD1
WA22218EALLSKD1
WA22220EALLSKD1
WA22222EALLSKD1
WA22224EALLSKD1
WA22226EALLSKD1
25
30
35
40
45
50
55
60
65
70
75
80
85
90
100
110
120
130
3040506580
100120140160180200225
3040506580
100120140160180200225250
15152020303540506065708090
2530354050607595
110120130140150
2530354050607595
110120130140150
4045556580
100120145170180200220240
4045556580
100120145170180200220240
55607590
110135160190220240260290320
55607590
110135160190220240260290320
7580
100120145180210240280310340380420
52
62
72
80
85
90
100
110
120
125
130
140
150
160
180
200
215
230
23
25
28
28
28
28
31
34
38
38
38
40
44
48
55
63
69
75
57.3
75.7
100
116
121
130
155
187
226
235
244
278
324
384
472
602
688
808
46.1
64.5
92
105
113
124
148
181
224
240
249
287
330
398
495
643
753
898
4,700
6,580
9,380
10,700
11,500
12,600
15,100
18,400
22,900
24,400
25,400
29,300
33,600
40,600
50,500
65,600
76,800
91,600
5,840
7,720
10,200
11,800
12,300
13,300
15,800
19,100
23,100
24,000
24,800
28,400
33,000
39,200
48,100
61,400
70,100
82,400
1
1
1.1
1.1
1.1
1.1
1.5
1.5
1.5
1.5
1.5
2
2
2
2.1
2.1
2.1
3
1.5
2
2
2.5
2.5
2.5
3
3
3.5
3.5
3.5
3.5
3.5
4.5
5
6
6
6
3
4
5
5
6
6
6
7
8
7
7
8
8
10
11
12
12
13
Bearing numbers Boundary dimensionsmm
Nominal borediameter
1) Cylindrical bore
mm
C2 CN C3 C4d
kN kgfCylindrical bore
over incl. min max min max min max min max
Unit:µm Unit:µm
Tapered bore d D B W0 C0r C0rCr Crrs min d0
29
36
42
47
52
57
64
69
74
79
84
91
96
101
112
122
132
144
29
36
43
48
53
58
64
70
76
82
86
93
98
103
115
127
138
148
D1 W33
4 3
47
56
65
73
78
83
93
102
111
116
121
131
140
149
168
188
203
216
47
56
65
73
78
83
93
102
110
116
121
131
140
147
165
183
197
211
0.34
0.31
0.31
0.27
0.26
0.24
0.23
0.24
0.24
0.22
0.22
0.22
0.22
0.23
0.24
0.25
0.25
0.25
2.98
3.20
3.29
3.67
3.93
4.23
4.40
4.23
4.15
4.48
4.67
4.67
4.57
4.31
4.23
4.00
4.08
4.00
2.00
2.15
2.21
2.47
2.64
2.84
2.95
2.84
2.79
3.01
3.14
3.14
3.07
2.90
2.84
2.69
2.74
2.69
1.96
2.10
2.16
2.41
2.58
2.78
2.89
2.78
2.73
2.94
3.07
3.07
3.00
2.83
2.78
2.63
2.68
2.63
1.4~2.4
2.0~3.3
2.3~3.9
3.1~5.2
3.4~5.7
3.4~5.6
5.2~7.9
6.6~11.0
8.5~14.2
9.6~16.0
9.9~16.4
12.2~20.3
16.9~28.1
20.4~34.1
28.8~48.0
41.6~69.3
52.8~88.0
62.6~104.4
0.19
0.30
0.50
0.58
0.63
0.70
0.94
1.25
1.72
1.78
1.88
2.32
2.90
3.68
5.40
7.79
9.76
11.9
-
-
0.49
0.57
0.61
0.68
0.91
1.22
1.67
1.73
1.83
2.27
2.83
3.59
5.25
7.58
9.48
11.6
1
1
1.1
1.1
1.1
1.1
1.5
1.5
1.5
1.5
1.5
2
2
2
2.1
2.1
2.1
3
Abutment and fillet dimensions Axial load factor Amount of grease(approx.)
Constant Mass (approx.)
Cylindricalbore
Taperedbore
ged1 D1da min Da max Y1 Y2 Y0rs max
BW0
Z0×d0
r
r
φD
φD
1
φd
φd
1
φd
ra
ra
φD
a
φd
a
1 Y1 0.67 Y2
Fa
Fr
X Y X Y
≦eFa
Fr>e
Equivalent radial loaddynamicPr=XFr+YFaOil inlet number
staticPor=Fr+YoFa
For values of e, Y1, Y2 and Yo
see the table below.
Z0
Dimension Table
Bearing Internal Clearance NTN Standard Grease Allowable Speed
Allowable Misalignment
Bearing Number
Allowable Temperature Range
Sealed Spherical Roller Bearings【WA Type】● Brand name: Shell Alvania EP grease No.2 High performance grease for heavy duty containing extreme pressure additives.● Amount of grease: 15~25% of inside free space of the bearing.
● With relubrication : dn≦6×104
● Without relubrication : dn≦8×104
● 0.009 rad (0.5˚)
Features
● Bearing temperature : -20~+1100
WA 222 20 EA LLS K D1 C3Internal clearance codeLubrication hole / lubrication groove code
W33: With oil inlet/oil groove (European market specication)
Bore configuration code No code: Cylindrical bore K: Tapered bore
Seal type codeDimension series codeBore diameter code
Contact seal on both sidesType code EA: Window-type presed steel cage
3040506580
100120140160180200225
3040506580
100120140160180200225250
202530405055658090
100110120140
303545557080
100120130140160180200
303545557080
100120130140160180200
4050607595
110135160180200220250270
4050607595
110135160180200220250270
55658095
120140170200230260290320350
55658095
120140170200230260290320350
7585
100120150180220260300340370410450
2) Tapered bore
mm
C2 CN C3 C4d
over incl. min max min max min max min max
1. The industry’s highest load capacity Both a high load capacity and a longer service life are achieved by adopting the internal design of EA type spherical roller bearing which has a significantly increased roller diameter and the maximum number of rollers guided with the window-type pressed steel cage.
2. Compact design with minimized volume of seals Adopt the contact type dust-proof seal with minimized volume. ① Prevent from intrusion of foreign matters with uniquely designed contact type rubber seals. ② Secure the dust-proof capability by maintaining the constant contact pressure of seals even under aligned conditions.
3. Prelubricated with a long life grease as standard Barings are prelubricated with a long life grease. No cleaning nor greasing are required when being mounted.
4. Oil groove and holes are adopted as standard Adequate greasing into the inside of the bearing is secured with a lubrication groove and holes on the outside diameter of the outer ring.
conventionaldesign of NTN
Grease flow
ULTAGE
・Larger rollers provide theindustry’s highest
load capacity.・Extended maintenance
intervals・Lighter and more
compact design
・Prevent from intrusionof foreign matters
・Prolonged relubricationinterval
・Unique structurereadily accepts lubricant・Pre-lubricated as
standard withlong life grease
Outer ring●With oil inlets and oil groove●Optimal curvature
Inner ring●No rib required●Optimal curvature
Rollers●Larger rollers●Maximum number of rollers
Seal●Contact seals on both sides●Unique lip structure to maintain the contact pressure even under being alignedCage
●Window-type pressed steel cage●Cage end faces function as guides
ULTAGE Sealed Spherical Roller Bearings [ WA Type ]
®
1
1 Tapered bore ratio of 1:12. 2 Smallest allowable dimension for chamfer dimension r.
2
"ULTAGE " (a name created from the combination of "ultimate," signifying refinement,and "stage," signifying NTN's intentionthat this series of products be employed in diverse applications) is the general name for NTN's new generation of bearings thatare noted for their industry-leading performance.
®
®
Basic load ratingsdynamic static staticdynamic
(d= inner bore diameter dimension, mm) × (n= operating speed, min-1)
Nominal borediameter
D1 : With oil inlet/oil groove (D1 specication only)
Up to five timeslonger service life
ULTAGE Series Sealed Spherical Roller Bearings (WA Type) are new innovative standardproducts specifically developed to provide “longer service life”, “higher reliability” and“improved ease of use” required for all industrial machineries.
ULTAGE Series Sealed Spherical Roller Bearings (WA Type) are new innovative standardproducts specifically developed to provide “longer service life”, “higher reliability” and“improved ease of use” required for all industrial machineries.
**自動調心ころWA_E_**自動調心ころWA 13/07/16 13:43 ページ 1
WA22205EALLSW33
WA22206EALLSW33
WA22207EALLSW33
WA22208EALLSD1
WA22209EALLSD1
WA22210EALLSD1
WA22211EALLSD1
WA22212EALLSD1
WA22213EALLSD1
WA22214EALLSD1
WA22215EALLSD1
WA22216EALLSD1
WA22217EALLSD1
WA22218EALLSD1
WA22220EALLSD1
WA22222EALLSD1
WA22224EALLSD1
WA22226EALLSD1
WA22207EALLSKW33
WA22208EALLSKD1
WA22209EALLSKD1
WA22210EALLSKD1
WA22211EALLSKD1
WA22212EALLSKD1
WA22213EALLSKD1
WA22214EALLSKD1
WA22215EALLSKD1
WA22216EALLSKD1
WA22217EALLSKD1
WA22218EALLSKD1
WA22220EALLSKD1
WA22222EALLSKD1
WA22224EALLSKD1
WA22226EALLSKD1
25
30
35
40
45
50
55
60
65
70
75
80
85
90
100
110
120
130
3040506580
100120140160180200225
3040506580
100120140160180200225250
15152020303540506065708090
2530354050607595
110120130140150
2530354050607595
110120130140150
4045556580
100120145170180200220240
4045556580
100120145170180200220240
55607590
110135160190220240260290320
55607590
110135160190220240260290320
7580
100120145180210240280310340380420
52
62
72
80
85
90
100
110
120
125
130
140
150
160
180
200
215
230
23
25
28
28
28
28
31
34
38
38
38
40
44
48
55
63
69
75
57.3
75.7
100
116
121
130
155
187
226
235
244
278
324
384
472
602
688
808
46.1
64.5
92
105
113
124
148
181
224
240
249
287
330
398
495
643
753
898
4,700
6,580
9,380
10,700
11,500
12,600
15,100
18,400
22,900
24,400
25,400
29,300
33,600
40,600
50,500
65,600
76,800
91,600
5,840
7,720
10,200
11,800
12,300
13,300
15,800
19,100
23,100
24,000
24,800
28,400
33,000
39,200
48,100
61,400
70,100
82,400
1
1
1.1
1.1
1.1
1.1
1.5
1.5
1.5
1.5
1.5
2
2
2
2.1
2.1
2.1
3
1.5
2
2
2.5
2.5
2.5
3
3
3.5
3.5
3.5
3.5
3.5
4.5
5
6
6
6
3
4
5
5
6
6
6
7
8
7
7
8
8
10
11
12
12
13
Bearing numbers Boundary dimensionsmm
Nominal borediameter
1) Cylindrical bore
mm
C2 CN C3 C4d
kN kgfCylindrical bore
over incl. min max min max min max min max
Unit:µm Unit:µm
Tapered bore d D B W0 C0r C0rCr Crrs min d0
29
36
42
47
52
57
64
69
74
79
84
91
96
101
112
122
132
144
29
36
43
48
53
58
64
70
76
82
86
93
98
103
115
127
138
148
D1 W33
4 3
47
56
65
73
78
83
93
102
111
116
121
131
140
149
168
188
203
216
47
56
65
73
78
83
93
102
110
116
121
131
140
147
165
183
197
211
0.34
0.31
0.31
0.27
0.26
0.24
0.23
0.24
0.24
0.22
0.22
0.22
0.22
0.23
0.24
0.25
0.25
0.25
2.98
3.20
3.29
3.67
3.93
4.23
4.40
4.23
4.15
4.48
4.67
4.67
4.57
4.31
4.23
4.00
4.08
4.00
2.00
2.15
2.21
2.47
2.64
2.84
2.95
2.84
2.79
3.01
3.14
3.14
3.07
2.90
2.84
2.69
2.74
2.69
1.96
2.10
2.16
2.41
2.58
2.78
2.89
2.78
2.73
2.94
3.07
3.07
3.00
2.83
2.78
2.63
2.68
2.63
1.4~2.4
2.0~3.3
2.3~3.9
3.1~5.2
3.4~5.7
3.4~5.6
5.2~7.9
6.6~11.0
8.5~14.2
9.6~16.0
9.9~16.4
12.2~20.3
16.9~28.1
20.4~34.1
28.8~48.0
41.6~69.3
52.8~88.0
62.6~104.4
0.19
0.30
0.50
0.58
0.63
0.70
0.94
1.25
1.72
1.78
1.88
2.32
2.90
3.68
5.40
7.79
9.76
11.9
-
-
0.49
0.57
0.61
0.68
0.91
1.22
1.67
1.73
1.83
2.27
2.83
3.59
5.25
7.58
9.48
11.6
1
1
1.1
1.1
1.1
1.1
1.5
1.5
1.5
1.5
1.5
2
2
2
2.1
2.1
2.1
3
Abutment and fillet dimensions Axial load factor Amount of grease(approx.)
Constant Mass (approx.)
Cylindricalbore
Taperedbore
ged1 D1da min Da max Y1 Y2 Y0rs max
BW0
Z0×d0
r
r
φD
φD
1
φd
φd
1
φd
ra
ra
φD
a
φd
a
1 Y1 0.67 Y2
Fa
Fr
X Y X Y
≦eFa
Fr>e
Equivalent radial loaddynamicPr=XFr+YFaOil inlet number
staticPor=Fr+YoFa
For values of e, Y1, Y2 and Yo
see the table below.
Z0
Dimension Table
Bearing Internal Clearance NTN Standard Grease Allowable Speed
Allowable Misalignment
Bearing Number
Allowable Temperature Range
Sealed Spherical Roller Bearings【WA Type】● Brand name: Shell Alvania EP grease No.2 High performance grease for heavy duty containing extreme pressure additives.● Amount of grease: 15~25% of inside free space of the bearing.
● With relubrication : dn≦6×104
● Without relubrication : dn≦8×104
● 0.009 rad (0.5˚)
Features
● Bearing temperature : -20~+1100
WA 222 20 EA LLS K D1 C3Internal clearance codeLubrication hole / lubrication groove code
W33: With oil inlet/oil groove (European market specication)
Bore configuration code No code: Cylindrical bore K: Tapered bore
Seal type codeDimension series codeBore diameter code
Contact seal on both sidesType code EA: Window-type presed steel cage
3040506580
100120140160180200225
3040506580
100120140160180200225250
202530405055658090
100110120140
303545557080
100120130140160180200
303545557080
100120130140160180200
4050607595
110135160180200220250270
4050607595
110135160180200220250270
55658095
120140170200230260290320350
55658095
120140170200230260290320350
7585
100120150180220260300340370410450
2) Tapered bore
mm
C2 CN C3 C4d
over incl. min max min max min max min max
1. The industry’s highest load capacity Both a high load capacity and a longer service life are achieved by adopting the internal design of EA type spherical roller bearing which has a significantly increased roller diameter and the maximum number of rollers guided with the window-type pressed steel cage.
2. Compact design with minimized volume of seals Adopt the contact type dust-proof seal with minimized volume. ① Prevent from intrusion of foreign matters with uniquely designed contact type rubber seals. ② Secure the dust-proof capability by maintaining the constant contact pressure of seals even under aligned conditions.
3. Prelubricated with a long life grease as standard Barings are prelubricated with a long life grease. No cleaning nor greasing are required when being mounted.
4. Oil groove and holes are adopted as standard Adequate greasing into the inside of the bearing is secured with a lubrication groove and holes on the outside diameter of the outer ring.
conventionaldesign of NTN
Grease flow
ULTAGE
・Larger rollers provide theindustry’s highest
load capacity.・Extended maintenance
intervals・Lighter and more
compact design
・Prevent from intrusionof foreign matters
・Prolonged relubricationinterval
・Unique structurereadily accepts lubricant・Pre-lubricated as
standard withlong life grease
Outer ring●With oil inlets and oil groove●Optimal curvature
Inner ring●No rib required●Optimal curvature
Rollers●Larger rollers●Maximum number of rollers
Seal●Contact seals on both sides●Unique lip structure to maintain the contact pressure even under being alignedCage
●Window-type pressed steel cage●Cage end faces function as guides
ULTAGE Sealed Spherical Roller Bearings [ WA Type ]
®
1
1 Tapered bore ratio of 1:12. 2 Smallest allowable dimension for chamfer dimension r.
2
"ULTAGE " (a name created from the combination of "ultimate," signifying refinement,and "stage," signifying NTN's intentionthat this series of products be employed in diverse applications) is the general name for NTN's new generation of bearings thatare noted for their industry-leading performance.
®
®
Basic load ratingsdynamic static staticdynamic
(d= inner bore diameter dimension, mm) × (n= operating speed, min-1)
Nominal borediameter
D1 : With oil inlet/oil groove (D1 specication only)
Up to five timeslonger service life
ULTAGE Series Sealed Spherical Roller Bearings (WA Type) are new innovative standardproducts specifically developed to provide “longer service life”, “higher reliability” and“improved ease of use” required for all industrial machineries.
ULTAGE Series Sealed Spherical Roller Bearings (WA Type) are new innovative standardproducts specifically developed to provide “longer service life”, “higher reliability” and“improved ease of use” required for all industrial machineries.
**自動調心ころWA_E_**自動調心ころWA 13/07/16 13:43 ページ 1
29
36
42
47
52
57
64
69
74
79
84
91
96
101
112
122
132
144
29
36
43
48
53
58
64
70
76
82
86
93
98
103
115
127
138
148
47
56
65
73
78
83
93
102
111
116
121
131
140
149
168
188
203
216
47
56
65
73
78
83
93
102
110
116
121
131
140
147
165
183
197
211
0.34
0.31
0.31
0.27
0.26
0.24
0.23
0.24
0.24
0.22
0.22
0.22
0.22
0.23
0.24
0.25
0.25
0.25
2.98
3.20
3.29
3.67
3.93
4.23
4.40
4.23
4.15
4.48
4.67
4.67
4.57
4.31
4.23
4.00
4.08
4.00
2.00
2.15
2.21
2.47
2.64
2.84
2.95
2.84
2.79
3.01
3.14
3.14
3.07
2.90
2.84
2.69
2.74
2.69
1.96
2.10
2.16
2.41
2.58
2.78
2.89
2.78
2.73
2.94
3.07
3.07
3.00
2.83
2.78
2.63
2.68
2.63
1.4~2.4
2.0~3.3
2.3~3.9
3.1~5.2
3.4~5.7
3.4~5.6
5.2~7.9
6.6~11.0
8.5~14.2
9.6~16.0
9.9~16.4
12.2~20.3
16.9~28.1
20.4~34.1
28.8~48.0
41.6~69.3
52.8~88.0
62.6~104.4
0.19
0.30
0.50
0.58
0.63
0.70
0.94
1.25
1.72
1.78
1.88
2.32
2.90
3.68
5.40
7.79
9.76
11.9
-
-
0.49
0.57
0.61
0.68
0.91
1.22
1.67
1.73
1.83
2.27
2.83
3.59
5.25
7.58
9.48
11.6
1
1
1.1
1.1
1.1
1.1
1.5
1.5
1.5
1.5
1.5
2
2
2
2.1
2.1
2.1
3
Abutment and fillet dimensions Axial load factor Amount of grease(approx.)
Constant Mass (approx.)
Cylindricalbore
Taperedbore
ged1 D1da min Da max Y1 Y2 Y0rs max
ra
ra
φD
a
φd
a
1 Y1 0.67 Y2
Fa
Fr
X Y X Y
≦eFa
Fr>e
Equivalent radial loaddynamicPr=XFr+YFa
staticPor=Fr+YoFa
For values of e, Y1, Y2 and Yo
see the table below.
NTN Standard Grease Allowable Speed
Allowable Misalignment
Bearing Number
Allowable Temperature Range
S ● Brand name: Shell Alvania EP grease No.2 High performance grease for heavy duty containing extreme pressure additives.● Amount of grease: 15~25% of inside free space of the bearing.
● With relubrication : dn≦6×104
● Without relubrication : dn≦8×104
● 0.009 rad (0.5˚)
F
● Bearing temperature : -20~+110"
WA 222 20 EA LLS K D1 C3Internal clearance codeLubrication hole / lubrication groove code
W33: With oil inlet/oil groove (European market specication)
Bore configuration code No code: Cylindrical bore K: Tapered bore
Seal type codeDimension series codeBore diameter code
Contact seal on both sidesType code EA: Window-type presed steel cage
Both a high load capacity and a longer service life are achieved by adopting the internal design of EA type spherical roller bearing which has a significantly increased roller diameter and the maximum number of rollers guided with the window-type pressed steel cage.
2 Adopt the contact type dust-proof seal with minimized volume. type rubber seals. of seals even under aligned conditions.
3 Barings are prelubricated with a long life grease. No cleaning nor greasing are required when being mounted.
4 Adequate greasing into the inside of the bearing is secured with a lubrication groove and holes on the outside diameter of the outer ring.
c
ULTAGE Sealed Spherical Roller Bearings [ WA Type ]
(d= inner bore diameter dimension, mm) × (n= operating speed, min-1)
D1 : With oil inlet/oil groove (D1 specication only)
**自動調心ころWA_E_**自動調心ころWA 13/07/17 9:33 ページ 1
1. Because the internal radial clearance of “ULTAGE Series Sealed Spherical Roller Bearings” with tapered bores cannot be measured with a thickness gauge, please monitor clearances by measuring the axial movement of the inner ring as shown in Table 1.
2. During assembly, if misalignment exceeding the allowable misalignment angle of ±0.5˚ is applied to the bearing, rollers may come in direct contact with seals causing seal deformation. Furthermore, if additional force is applied under these conditions, seals may separate from the bearing entirely. Therefore, caution is advised.
3. Please use Lithium mineral grease. In case other types of grease are to be used, please consult NTN.
4. If a shrink fit is to be applied, please do not exceed a bearing temperature of 100˚C. However, these bearing cannot be shrink fit via immersion in a hot oil bath.
Rotational speed min-1
Out
er ri
ng te
mpe
ratu
re ri
se ˚
C
Rot
atio
nal t
orqu
e N・
mm
00.0
20.0
40.0
60.0
80.0
100.0
200 400 600 800 1000 1200 1400 1600Rotational speed min-1
00
50
100
150
200
200 400 600 800 1000 1200 1400 1600
Performance Test Data
Handling Precautions
ULTAGE Sealed Spherical Roller Bearings [ WA Type ]
●Heat Run Test
[Test conditions] Bearing :WA22218EALLSD1 Load :Radial load 294N{30kgf} Speed :200~1400min-1
Lubrication :Shell Alvania EP grease No.2 (NTN code 8A) Amount of grease :20% of free space Operating time :Until temperature rise stabilizes
●Noise Test
[Test conditions] Bearing :WA22218EALLSD1 Load :Radial load 980N{100kgf} Speed :600, 900, 1200min-1
Lubrication :Shell Alvania EP grease No.2 (NTN code 8A) Amount of grease :20% of free space
●Grease Leakage Test
[Test conditions] Bearing :WA22218EALLSD1 Load :Radial load 1960N{200kgf} Speed :1000min-1
Lubrication :Shell Alvania EP grease No.2 (NTN code 8A) Amount of grease :20% of free space Operating time :100 hours
[Test results] [Test results]
[Test results]
Outer ring temperature rise Rotational torque
24
30
40
50
65
80
100
120
30
40
50
65
80
100
120
130
0.010
0.010
0.015
0.025
0.035
0.035
0.050
0.060
0.015
0.015
0.020
0.030
0.040
0.045
0.060
0.070
Nominal borediameter
Axialdisplacement
drive-up
Minimum residualinternal clearance
Reduction inradial internal
clearance
Table 1 Installing sealed tapered bore bearings
mmd
over incl. min max
0.15
0.20
0.30
0.35
0.45
0.60
0.75
0.85
0.20
0.25
0.35
0.40
0.55
0.70
0.85
0.95
min max
0.015
0.020
0.025
0.025
0.030
0.035
0.040
0.050
0.025
0.035
0.040
0.045
0.055
0.065
0.075
0.090
CN C3
0.040
0.050
0.060
0.065
0.080
0.095
0.110
0.130
C4
600
900
1200
Noize level dBA
min-1 50 60 70 80
[Test results]Accumulated total amount
of grease leakage
25h
0.47g
50h
0.58g
100h
0.63g
Rotationalspeed
Sealed Spherical Roller Bearings[WA Type]
CAT. No. 3703/ENote: Markings on the seal are not white in actual bearings.
**自動調心ころWA_E_**自動調心ころWA 13/07/17 9:33 ページ 2