The Wolf Sand Blaster is compact and affordable,and has all the features you’d hope for.

Two gloves make it easier to hold the pieces you are blasting.

The nozzle pivots to adjust for the dimensions ofthe piece you are working on. The on/off switch islocated inside the cabinet. It has a quick changenozzle to make it easy to attach the air hose.The Wolf Sandblaster also features an air filter toeliminate moisture which causes clumping, and adust filter to keep hazardous dust from your workspace. The lid is lined with replaceable clear film to protect the lid from being frosted.

®

Wolf Tools Kate Wolf (207) 871-1343 info@wolftools.biz P.O. Box 244, Portland, ME 04112

Operating Instructions

Pen Style Sand BlasterMMooddeell 5522--11772211

General Recommendations: • Use the Pen Style Blaster for decorating, blending and texturing metal, glass and wood

• Glass beads are a soft abrasive, they burnish without removing metal. Excellent for a bright satin finish

• Aluminum oxide is a soft, fast cutting abrasive 120/180 grit - that creates a matte finish and is generally used for blending surfaces and removing oxides and firescale

• Silicon carbide is not recommended as it is a contaminating media

• Normally use the smallest size of abrasive to do the job. A smaller size works faster because there are more impacts per pound, with more coverage and it reaches into intricate areas

• Due to the impact of the abrasive on the work piece, abrasives lose their edges after a period of use. It is best to replace abrasives completely (do not mix old abrasives with new)

• It is not recommended to mix two different types of abrasive, because the harder abrasive will overpower the softer abrasive and the softer abrasive will not have any visible effect on the work

• The ceramic nozzle orifice is 3mm in diameter.(#16) In use the orifice will tend to get larger. When the orifice enlarges to approx. 3.6 to 3.8mm it should be replaced. To replace the ceramic nozzle, pull the knurled end of the orifice out and push in new nozzle

• The Wolf Sand Blaster is compact and affordable,and has all the features you hope for. Two gloves make it easier to hold the pieces you are blasting

• The nozzle pivots to adjust for the dimensions of the piece you are working on. The on/off switch is located inside the cabinet. The Wolf Sandblaster also features an air filter to eliminate moisture which causes clumping, and a dustfilter to keep hazardous dust from your workspace. The quick change nozzle makes it easy to attach the air hose

• The lid is lined with replaceable clear film to protect the lid from being frosted

Wolf Tools Kate Wolf (207) 871-1343 info@wolftools.biz P.O. Box 244, Portland, ME 04112

Blasting Media: Surface preparation is of vital importance before polish-ing, burnishing and plating. Surface roughness may beimproved by blasting with media, either abrasives orglass beads. Different surface finishes may be generat-ed by varying the parameters of the micron size of abra-sives and air pressure. The degree of matte to satin fin-ish depends on the hardness of the material being fin-ished. Available in 5 lbs jars.

ITEM # DESCRIPTION GRADE MICRON GRIT

52-1541 GLASS BEADS COARSE 240 60

52-1542 GLASS BEADS MEDIUM 100 120

52-1543 GLASS BEADS FINE 60 220

52-1544 GLASS BEADS EX-FINE 20 320

52-1546 ALUMINUM OXIDE COARSE 180 80

52-1547 ALUMINUM OXIDE MEDIUM 100 120

52-1548 ALUMINUM OXIDE FINE 80 180

Pen StyledSand Blasting System

Manufactured by Ikohe®,

Makers of Wolf’s Precision WaxCarvers and other fine products.

Designed

to revolutionize

your finishing

processes on

Metals, Glass,

Wood and

Other Surfaces

Features: •

• Ergonomically designed, contoured cabinet for easy cleaning and maintenance• Easy to operate two hand model • Lightweight and portable with excellent visibility • Powerful, efficient, pressurized air-suction jet blasting.• Easy to change media • Less clogging and uniform flow of media with the specially designed air intake system • On/off control located inside the unit

81

2

146

10

11

4

Hinge

Panel Lock

5 Mesh

Viewing Panel

3 Lifting Handle

ClampRingGlass Beads/ Media

Dust Filter

9Control Switch

Air RegulatorKnob

Air Inlet

12Pressure

Gauge

13Air

Filter

15RubberGloves

16Ceramic

Nozzle

7Media Drain Plug

Technical Specifications:

Model: 52-1721Air Pressure: 40-70 PSI / 2 CFMBlasting Media: Glass Beads /

Aluminum Oxide

Dimensions: 20” X 17” X 17”Wt.: 12 Lbs

Unit Includes:•:

Regulator with Gauge 52-7401Pressure Gauge 52-7402Complete Dust Filter 52-7404Replaceable Filter 52-7405Mylar Protector 52-7414Blasting Nozzle 52-7416Latex Gloves(Pair) 52-7418

Cleaning and Maintenance: •

• It is never safe to inhale abrasives of any kind! Wear NIOSH approved dust mask when handling or using abrasives

• Empty used blasting media by removing the rubber drain plug at the bottom of the unit

• Clean the dust filter at least once a month- tap it gently, then unscrew theplastic jar and vacuum the filter

• Clean the surface on the outside of the cabinet using a cloth with with a mild detergent

• Never use solvent on any part of the unit

Manufactured by Ikohe- manufacturers of

Wolf’s Precision Wax Carvers and other fine fine products.

Thank you Ikohe! I love your tools!

-Kate Wolf

Caution! •

• Keep the unit away from direct sunlight• The unit must be operated in a well ventilated room• Do not exceed the maximum recommended air pressure• Do not open the viewing glass immediately after blasting • Use clean compressed air to protect the unit from being damaged• Never mix glass beads and aluminum oxide abrasive• When the dust filter gets clogged, tap the jar gently, then unscrew it and

vacuum the filter. Wear dust mask.

Operating Instructions:•

• Connect the air supply to the air inlet (11)• Open the viewing panel by turning the panel lock (4) counter clockwise • Pour the blasting media, glass beads or abrasives into the unit

(approximately 3 lbs.), make sure media is not above the mesh grate in the bottom of the blaster

• Put pieces to be blasted on mesh grate• Close the door by turning the panel lock clockwise • Always keep the panel door locked whenever the unit is in use to prevent

moisture entering and media from being blown out and inhaled• Turn on air compressor, and set pressure to approx. (65-80PSI)• Lift and turn the knob on the sandblaster's air regulator (10) to set the

pressure- do not exceed the recommended pressure for each media. When starting the comressor, it is necessary to pull down on teh drain valve on the bottom of the air filter (13) for a few seconds, until the pressure builds up enough for the valve to stay down on its. When the desired pressure is reached press down knob on top of air filter

• Inside the unit is a switch to activate the blasting nozzle• The blasting nozzle may be used in a fixed or free hand position

(slide nozzle out of bracket to use it free hand)• Turn off switch and allow media to settle before opening panel• When viewing is impaired, peel off and replace the protective mylar film• At the end of each use, push up on drain valve at the bottom of the air

filter to allow trapped moisture to drain out