TV

BD/DVD player Cable/Satellite Box

RX-V2065 Zone 2 Hookup Example

Zone 2

PR

EPAR

ATION

BAS

IC

OP

ER

ATION

PR

EPAR

ATION

AC IN

DOCK

SRONOHP -232C TRIGGER OUTNETWORK

COMPONENTVIDEO

PR

PB

1 2

Y

OPTICAL

OPTICAL

OUT

( TV )AV 1 AV 2

COAXIAL

AV 3(CD)

COAXIAL OPTICAL

AV 4 AV 5 AV 6AV

OUT AUDIO1 AUDIO2FRONT SURROUND SUR.BACK SUBWOOFER

MULTI CH INPUTAUDIOOUT

ZONE3OUT

ZONE2OUT

FRONT SURROUND SUR. BACK SUBWOOFER

PRE OUT

CENTERSINGLE

VIDEO

HDMI OUT 2HDMI OUT 1

ANTENNA

UNBAL.

FMHD Radio

GND AM

HDMI 1(BD/DVD)(HDMI CONTROL)

HDMI 2 HDMI 3 HDMI 4

VIDEO

IN

OUT

MONITOR OUT SPEAKERS

12V0.1A MAX.

FRONT CENTER

SINGLE CLASS 2 WIRING

SURROUND SURROUND BACK/BI-AMP

ZONE2/PRESENCEZONE3

1 2

CENTER

PR

PB

Y

REMOTE

COMPONENTVIDEO

SIRIUS

DIGITALAUDIO

GND

XM

EXTRA SPSP2 SP1

OUT 1HDMI

INHDMI

Analog Output

OUTHDMI

OUTHDMI

Analog Output

Audio 1 Input

Audio 2Input

IN 1HDMI HDMI

IN 2

To select the Cable/Satellite Box as asource for Zone 2, the Audio 2 inputon the receiver must be selected in

NOTE:

To select the BD/DVD player as asource for Zone 2, the Audio 1 inputon the receiver must be selected in

NOTE:

Zone 2. Zone 2

Extra SPZone 2/ PresenceSpeaker Terminal

Zone 2 setup on the RX-V2065 using the Internal Power Amp

The RX-V2065 Extra Speaker Terminals can power one set of speakers for Zone 2 or Presence speakers. If the Extra Speaker Terminals are utilized then the RX-V2065 cannot be set for 7.1 (Surround Back terminals.) or Bi Amp (Surround Back terminals.)

Setting the Extra Speaker Terminals  Note: The RX-V2065 remote control will be used to access the Setup Menu of receiver.

1. Press the On Screen button on the remote control to enter the. 2. Scene BD/DVD will come up on the receiver LED Screen. 3. Arrow down to until Setup comes up in the receiver LED Screen. 4. Press the Enter Button on the remote control. 5. Setup/Speaker Setup will come up on the receiver LED Screen. 6. Press the Enter Button on the remote control. 7. SP Set/1. Auto Setup will come up on the receiver LED Screen. 8. Arrow down until 2 Manual Setup comes up in the receiver LED Screen. 9. Press the Enter Button on the remote control. 10. SP/Set, A) Config will come up on the receiver LED Screen. 11. Press the Enter Button on the remote control. 12. Config, Extra………None will come up on the receiver LED Screen. 13. Use the Left/Right Arrow buttons on the remote to change the Extra to: Extra……….Zone2. 14. Use the Return and Setup buttons on the remote to exit the Setup Menu. 15. Extra Speaker setup is complete.

To control Zone 2 using the RX-V2065 remote the switch at the upper most left hand corner of the remote must be set to Zone 2. Once the remote has been set to Zone 2 the following commands will be available:

1. Selecting the input source (AV5-6, AUDIO1-2, and V-AUX) of Zone 2. 2. Adjusting the volume of Zone 2 (when a Zone 2 speaker is connected to the EXTRA SP jack). 3. Tuning into FM or AM when “TUNER” is selected as the input source of Zone 2 (see page 29 of

the owner’s manual). 4. Tuning into XM Satellite Radio when “XM” is selected as the input source of Zone 2 (see page

33) (U.S.A. model only). 5. Tuning into SIRIUS Satellite Radio when “SIRIUS” is selected as the input source of Zone 2

(see page 37) (U.S.A. model only). 6. Playing back music stored on your iPod stationed in a Yamaha iPod universal dock (such as

YDS-10, YDS-11 and YDS-12 sold separately) connected to the DOCK terminal. Note: Only Analog signals can be sent to Zone 2. If you want to output the sound from Zone 2, connect an external component to AV 5-6 or Audio 1-2 by analog connection. Important Safety Notice: The EXTRA SP Speaker Terminals of this unit should not be connected to a Passive Loudspeaker Selector Box or more than one Loudspeaker per Channel. Connection to a Passive Loudspeaker Selector Box or Multiple Speakers per channel could create an abnormally low impedance load resulting in amplifier damage.