pd-h2-118s 18” horn loaded subwoofer
TRANSCRIPT
© 2017, Precision Devices International Ltd. We operate a policy of continuous research and development and as such published specifications are subject to change without notice. Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.com WWW.PRECISION-DEVICES.COM
MATERIALWe recommend the use of a multi-layer, void free, exterior grade birch ply. Thickness should be at least 18mm (3/4”) and 24mm (1”) for larger enclosures. Other kinds of wood (e.g. Pine, blackboard and hardwoods) may be used for construction, but the resulting strength and acoustic properties will be affected. As a cheaper option Medium Density Fibreboard (MDF) or flooring-grade chipboard can be used where the cabinet is to be permanently installed in a dry situation.
METHOD / TECHNIQUEWe recommend lapped joints, however simple butt joints are adequate, both types of joint should be airtight. All joints should be bonded with a sufficient bead of glue to ensure good adhesion (PVA or PU glue is suitable) and screwed at 200mm (8”) centres with 4.2mm or 4.8mm (No.8 or 10 gauge) x 60mm (2 3/8”) screws. A high quality wood screw should be used. Make sure there’s a clearance hole in the wood that the screw head bears down on, so the pieces of wood are pulled fully together. To curtail major resonances (e.g. spurious buzzing noises), major panels should be stiffened with battens; off-cuts are often used, however we recommend purpose made braces for optimum performance. These should be glued and screwed into place. The arrangement must be consistent (between like cabinets) to ensure performance remains the same. To reduce panel resonance further a larger number of smaller braces can be used.
HOLE CUTTINGFixing holes to mount the loudspeaker may be defined using the holes in the driver frame. The loudspeaker is then mounted using bolts and ‘T’ nuts supplied. All other holes for connectors, handles, etc should be cut before any other parts are mounted.
PASSIVE CROSSOVERSUnless otherwise stated, cabinet designs are passive units, and adequate external signal processing arrangements should be made to filter out signals.
Where used, crossover networks should be mounted for ease of access, but at the same time they should be kept away from the immediate vicinity of the driver(s)’ magnets. Crossover PCBs need to be firmly secured; buzzing or rattling will impair sound quality. If a crossover breaks loose in transit, the crossover and/or drivers may be damaged. Self-tapping screws provide the suitable fixing, taking care to ensure a tight fit. Screw cups spread out the pressure exerted on the PCB, reducing the chances of damage if the cabinet is dropped from a height. Rubber grommets can be used to space the crossover PCB off the cabinet wall, and can protect the PCB/components from the resulting shock.
CONNECTORSSome connectors leak air. Be sure to check the connectors are suitable for the application intended.
INTERNAL WIRINGWiring should be clearly coded so correct polarity is visible. We recommend red and black for hot (+ve) and cold (-ve) respectively. When the enclosure is first tested, use a battery or polarity (‘phase’)-checker set to ensure that the driver(s)’ cones move forwards (outwards) when the hot (+ve) input terminal is driven positive.
ACOUSTIC TREATMENTThe inside of the enclosure should be lagged with an absorptive material, to dampen internal reflections and standing waves. Recommended materials are BAF or a similar cushion filler. For best results staple the wadding to the cabinet walls. The amount of wadding will affect the acoustic performance of the enclosure and is best adjusted to give the desired response. Plans will indicate where any wadding is best positioned.
DRIVE UNITSBefore mounting the drive units, the internal wing, connectors (and passive crossovers where applicable) should be fitted. Make sure the cabinet interior is clear and free from swarf and waste. Drive units are fitted with a foam sealing strip to provide airtight conditions when bolted down. Make sure this is in place and intact before fixing the driver. The driver’s fixing bolts should be tightened in stages, in a diagonal sequence to avoid possible deformation of the chassis or baffle.
Further information about our drive units can be found at http://www.precision-devices.com
ENCLOSURE CONSTRUCTION HINTS & TIPS
© 2017, Precision Devices International Ltd. We operate a policy of continuous research and development and as such published specifications are subject to change without notice. Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.com WWW.PRECISION-DEVICES.COM
SUB BASS DRIVERPD.185C003
THIELE SMALL PARAMETERS (8Ω MODEL)
SPECIFICATIONSNominal Diameter 18” / 457.2 mm
Voice Coil Diameter 5.0” / 127 mm
Power Rating 1000 W (A.E.S.)
Peak Power (6dB Crest Factor) 4000 W (A.E.S.)
Sensitivity (1w - 1m) 99 dB
Frequency Range 30 Hz - 500 Hz
Recommended Enclosure Vol. 90 - 250 Litres
Resonance 33 Hz
Voice Coil Winding Depth 28.00 mm / 1.10”
Magnet Gap Depth 12.0 mm / 0.47”
Flux Density 1.25 Tesla
Magnet Material Y35 Ferrite
Voice Coil MaterialCopper (Inside / outside winding)
MOUNTING INFORMATIONChassis Shoulder Diameter 415 mm
Outer Bolt Circle 6x M6 on 456 mm PCD
Fs 33 Hz
Re 5.4 Ω
Qms 10.60
Qes 0.229
Qts 0.240
Le (@ 1 kHz) 2.80 mH
Le (@ 10 kHz) 1.360 mH
Vas 224 Litres
Mms 197.00 g
Sd 1164 cm2
Cms 118.00 μm/N
BL 31.50 T/m
Xmax 11.00 mm
Vd 1.274 Litres
Ref. Efficiency 3.40%
EBP 144.10 Hz
COMPONENTS & SPECIFICATIONS
Full driver specifications can be found at: http://www.precision-devices.com
A wide range of speaker cabinet accessories
are available from specialist suppliers. Wheels,
grilles, corner protectors, paint, connectors
and handles should be carefully fitted to
avoid air leaks or weakening the enclosure.
Important Note: For optimum performance
we recommend using the enclosure in
multiples of no less than two.
• High Performance, 1x 18”, Horn-loaded
Subwoofer System.
• Optimised for PD.185C003.
+120
+110
+100
+90
+80
+70
+60
+50
dB (1
W-1m
)
20 50 100 200 500 1k 2k 5k 10k 20k(Hz)
200
100
50
20
10
5
2
1
Ohm
s (Ω)
20 50 100 200 500 1k 2k 5k 10k 20k(Hz)
FREQUENCY RESPONSE AND IMPEDANCE CHARTS
140318
© 2017, Precision Devices International Ltd. We operate a policy of continuous research and development and as such published specifications are subject to change without notice. Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.com
PD-H2-118SREVISION: SHEET:SCALE: DIMENSIONS:
TOLERANCE LINEAR ± 0.4, HOLES +0.1/-0.0, NONE - CUMULATIVE
PROJECT: PART:
NOTES:
1.0 4 OF 24N/A MMWWW.PRECISION-DEVICES.COM
H2-Cabinet Design for PD-185C03
DRAWN
NAME
TITLE:
DWG NO.
H2-118S. Cabinet and Driver
Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.comwww.precision-devices.com
MM1.0NOTES:
PART:PROJECT:
LATIVE - CUMUONE +0.1/-0.0, NOLESH ± 0.4, INEAR LOLERANCET
DIMENSIONS:SCALE: SHEET:REVISION:
PD-H2-118S
021117
TITLE:
Precision Devices International Ltd. We operate a policy of continuous research and development and as such published specifications are subject to change without notice.
Cabinet Construction Detail
140318
© 2017, Precision Devices International Ltd. We operate a policy of continuous research and development and as such published specifications are subject to change without notice. Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.com
PD-H2-118SREVISION: SHEET:SCALE: DIMENSIONS:
TOLERANCE LINEAR ± 0.4, HOLES +0.1/-0.0, NONE - CUMULATIVE
PROJECT: PART:
NOTES:
1.0 5 OF 24N/A MMWWW.PRECISION-DEVICES.COM
H2-Cabinet Design for PD-185C03
DRAWN
NAME
TITLE:
DWG NO.
H2-118S. Cabinet and Driver
Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.comwww.precision-devices.com
MM1.0NOTES:
PART:PROJECT:
LATIVE - CUMUONE +0.1/-0.0, NOLESH ± 0.4, INEAR LOLERANCET
DIMENSIONS:SCALE: SHEET:REVISION:
PD-H2-118S
021117
TITLE:
Precision Devices International Ltd. We operate a policy of continuous research and development and as such published specifications are subject to change without notice.DRAWN
NAME
TITLE:
DWG NO.
H2-118S. Cabinet and Driver 1 1
Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.comwww.precision-devices.com
MM1.0NOTES:
PART:PROJECT:
LATIVE - CUMUONE +0.1/-0.0, NOLESH ± 0.4, INEAR LOLERANCET
DIMENSIONS:SCALE: SHEET:REVISION:
PD-H2-118S
021117
TITLE:
Precision Devices International Ltd. We operate a policy of continuous research and development and as such published specifications are subject to change without notice.
Driver Mounting Configuration
140318
© 2017, Precision Devices International Ltd. We operate a policy of continuous research and development and as such published specifications are subject to change without notice. Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.com
PD-H2-118SREVISION: SHEET:SCALE: DIMENSIONS:
TOLERANCE LINEAR ± 0.4, HOLES +0.1/-0.0, NONE - CUMULATIVE
PROJECT: PART:
NOTES:
1.0 6 OF 24N/A MMWWW.PRECISION-DEVICES.COM
1
2
3
4
5
6
7
8
9
10
11
12
15
13
Parts Key
140318
© 2017, Precision Devices International Ltd. We operate a policy of continuous research and development and as such published specifications are subject to change without notice. Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.com
PD-H2-118SREVISION: SHEET:SCALE: DIMENSIONS:
TOLERANCE LINEAR ± 0.4, HOLES +0.1/-0.0, NONE - CUMULATIVE
PROJECT: PART:
NOTES:
1.0 7 OF 24N/A MMWWW.PRECISION-DEVICES.COM
Cabinet Construction Detail
140318
© 2017, Precision Devices International Ltd. We operate a policy of continuous research and development and as such published specifications are subject to change without notice. Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.com
PD-H2-118SREVISION: SHEET:SCALE: DIMENSIONS:
TOLERANCE LINEAR ± 0.4, HOLES +0.1/-0.0, NONE - CUMULATIVE
PROJECT: PART:
NOTES:
1.0 8 OF 24N/A MMWWW.PRECISION-DEVICES.COM
Cabinet Construction Detail
140318
© 2017, Precision Devices International Ltd. We operate a policy of continuous research and development and as such published specifications are subject to change without notice. Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.com
PD-H2-118SREVISION: SHEET:SCALE: DIMENSIONS:
TOLERANCE LINEAR ± 0.4, HOLES +0.1/-0.0, NONE - CUMULATIVE
PROJECT: PART:
NOTES:
1.0 9 OF 24N/A MMWWW.PRECISION-DEVICES.COM
Acoustic Wadding Placement
140318
© 2017, Precision Devices International Ltd. We operate a policy of continuous research and development and as such published specifications are subject to change without notice. Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.com
PD-H2-118SREVISION: SHEET:SCALE: DIMENSIONS:
TOLERANCE LINEAR ± 0.4, HOLES +0.1/-0.0, NONE - CUMULATIVE
PROJECT: PART:
NOTES:
1.0 10 OF 24N/A MMWWW.PRECISION-DEVICES.COM
823
810
135°
18
55
44°
355
17.74°
515
102.88°
339
90°
36
18 83.63
663
18
810
10
74.
65°
195.05
DRAWN
NAME
TITLE:
DWG NO.
H2-118S SIDE
Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.comwww.precision-devices.com
MM1.0NOTES:
PART:PROJECT:
LATIVE - CUMUONE +0.1/-0.0, NOLESH ± 0.4, INEAR LOLERANCET
DIMENSIONS:SCALE: SHEET:REVISION:
PD-H2-118S
021117
TITLE:
Precision Devices International Ltd. We operate a policy of continuous research and development and as such published speci�cations are subject to change without notice.
1. Right Side Panel
18mm Ply.
140318
© 2017, Precision Devices International Ltd. We operate a policy of continuous research and development and as such published specifications are subject to change without notice. Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.com
PD-H2-118SREVISION: SHEET:SCALE: DIMENSIONS:
TOLERANCE LINEAR ± 0.4, HOLES +0.1/-0.0, NONE - CUMULATIVE
PROJECT: PART:
NOTES:
1.0 11 OF 24N/A MMWWW.PRECISION-DEVICES.COM
823
810
10 18
55
355
515
44°
17.74° 102.88°
663
135° 18
90°
339
18
83.63
36
DRAWN
NAME
TITLE:
DWG NO.
H2-118S SIDE 2
Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.comwww.precision-devices.com
MM1.0NOTES:
PART:PROJECT:
LATIVE - CUMUONE +0.1/-0.0, NOLESH ± 0.4, INEAR LOLERANCET
DIMENSIONS:SCALE: SHEET:REVISION:
PD-H2-118S
021117
TITLE:
Precision Devices International Ltd. We operate a policy of continuous research and development and as such published speci�cations are subject to change without notice.
2. Left Side Panel
18mm Ply.
140318
© 2017, Precision Devices International Ltd. We operate a policy of continuous research and development and as such published specifications are subject to change without notice. Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.com
PD-H2-118SREVISION: SHEET:SCALE: DIMENSIONS:
TOLERANCE LINEAR ± 0.4, HOLES +0.1/-0.0, NONE - CUMULATIVE
PROJECT: PART:
NOTES:
1.0 12 OF 24N/A MMWWW.PRECISION-DEVICES.COM
836
10
590
560
280
A
A
560
18
18
5
9
SECTION A-A SCALE 1 : 5
DRAWN
NAME
TITLE:
DWG NO.
H2-118S TOP
Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.comwww.precision-devices.com
MM1.0NOTES:
PART:PROJECT:
LATIVE - CUMUONE +0.1/-0.0, NOLESH ± 0.4, INEAR LOLERANCET
DIMENSIONS:SCALE: SHEET:REVISION:
PD-H2-118S
021117
TITLE:
Precision Devices International Ltd. We operate a policy of continuous research and development and as such published speci�cations are subject to change without notice.
3. Top Panel
18mm Ply.
140318
© 2017, Precision Devices International Ltd. We operate a policy of continuous research and development and as such published specifications are subject to change without notice. Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.com
PD-H2-118SREVISION: SHEET:SCALE: DIMENSIONS:
TOLERANCE LINEAR ± 0.4, HOLES +0.1/-0.0, NONE - CUMULATIVE
PROJECT: PART:
NOTES:
1.0 13 OF 24N/A MMWWW.PRECISION-DEVICES.COM
836 5
60
150
R10
250
470
18
96.50
808
18
19
692.50
10 18
96.50 18
808
19 692.50
5
20
290
510
105 80.50
R30
105
10
5 1
05
105
AA
B
SECTION A-A
9 30
DETAIL B SCALE 1 : 2
DRAWN
NAME
TITLE:
DWG NO.
H2-118S BOTTOM .1
Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.comwww.precision-devices.com
MM1.0NOTES:
PART:PROJECT:
LATIVE - CUMUONE +0.1/-0.0, NOLESH ± 0.4, INEAR LOLERANCET
DIMENSIONS:SCALE: SHEET:REVISION:
PD-H2-118S
021117
TITLE:
Precision Devices International Ltd. We operate a policy of continuous research and development and as such published speci�cations are subject to change without notice.
4. Bottom Panel
18mm Ply.
140318
© 2017, Precision Devices International Ltd. We operate a policy of continuous research and development and as such published specifications are subject to change without notice. Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.com
PD-H2-118SREVISION: SHEET:SCALE: DIMENSIONS:
TOLERANCE LINEAR ± 0.4, HOLES +0.1/-0.0, NONE - CUMULATIVE
PROJECT: PART:
NOTES:
1.0 14 OF 24N/A MMWWW.PRECISION-DEVICES.COM
560
810
70
110
R10
7
0
280
148
217
.50
18
18 18
Prodosed connector plate position.Dimensions are arbitary
18 5
DRAWN
NAME
TITLE:
DWG NO.
H2-118S BACK
Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.comwww.precision-devices.com
MM1.0NOTES:
PART:PROJECT:
LATIVE - CUMUONE +0.1/-0.0, NOLESH ± 0.4, INEAR LOLERANCET
DIMENSIONS:SCALE: SHEET:REVISION:
PD-H2-118S
021117
TITLE:
Precision Devices International Ltd. We operate a policy of continuous research and development and as such published speci�cations are subject to change without notice.
5. Back Panel
18mm Ply.
140318
© 2017, Precision Devices International Ltd. We operate a policy of continuous research and development and as such published specifications are subject to change without notice. Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.com
PD-H2-118SREVISION: SHEET:SCALE: DIMENSIONS:
TOLERANCE LINEAR ± 0.4, HOLES +0.1/-0.0, NONE - CUMULATIVE
PROJECT: PART:
NOTES:
1.0 15 OF 24N/A MMWWW.PRECISION-DEVICES.COM
6. Back Brace
435
74.65°
139
5
23.34°
44.48°
534
DRAWN
NAME
TITLE:
DWG NO.
H2-118S back brace
Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.comwww.precision-devices.com
MM1.0NOTES:
PART:PROJECT:
LATIVE - CUMUONE +0.1/-0.0, NOLESH ± 0.4, INEAR LOLERANCET
DIMENSIONS:SCALE: SHEET:REVISION:
PD-H2-118S
021117
TITLE:
Precision Devices International Ltd. We operate a policy of continuous research and development and as such published speci�cations are subject to change without notice.
18mm Ply.
140318
© 2017, Precision Devices International Ltd. We operate a policy of continuous research and development and as such published specifications are subject to change without notice. Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.com
PD-H2-118SREVISION: SHEET:SCALE: DIMENSIONS:
TOLERANCE LINEAR ± 0.4, HOLES +0.1/-0.0, NONE - CUMULATIVE
PROJECT: PART:
NOTES:
1.0 16 OF 24N/A MMWWW.PRECISION-DEVICES.COM
7. Corner Brace
212
82
534
18
176
45°
212
45°
A
18
5
DETAIL A SCALE 1 : 1
DRAWN
NAME
TITLE:
DWG NO.
HS2-CORNER-BRACE 1
Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.comwww.precision-devices.com
MM1.0NOTES:
PART:PROJECT:
LATIVE - CUMUONE +0.1/-0.0, NOLESH ± 0.4, INEAR LOLERANCET
DIMENSIONS:SCALE: SHEET:REVISION:
PD-H2-118S
021117
TITLE:
Precision Devices International Ltd. We operate a policy of continuous research and development and as such published speci�cations are subject to change without notice.
18mm Ply.
140318
© 2017, Precision Devices International Ltd. We operate a policy of continuous research and development and as such published specifications are subject to change without notice. Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.com
PD-H2-118SREVISION: SHEET:SCALE: DIMENSIONS:
TOLERANCE LINEAR ± 0.4, HOLES +0.1/-0.0, NONE - CUMULATIVE
PROJECT: PART:
NOTES:
1.0 17 OF 24N/A MMWWW.PRECISION-DEVICES.COM
8. Horn Brace 1
145
534
A
145
75.65°
18
18 5
DETAIL A SCALE 1 : 1
DRAWN
NAME
TITLE:
DWG NO.
HS2-HORN-BRACE 1
Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.comwww.precision-devices.com
MM1.0NOTES:
PART:PROJECT:
LATIVE - CUMUONE +0.1/-0.0, NOLESH ± 0.4, INEAR LOLERANCET
DIMENSIONS:SCALE: SHEET:REVISION:
PD-H2-118S
021117
TITLE:
Precision Devices International Ltd. We operate a policy of continuous research and development and as such published speci�cations are subject to change without notice.
18mm Ply.
140318
© 2017, Precision Devices International Ltd. We operate a policy of continuous research and development and as such published specifications are subject to change without notice. Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.com
PD-H2-118SREVISION: SHEET:SCALE: DIMENSIONS:
TOLERANCE LINEAR ± 0.4, HOLES +0.1/-0.0, NONE - CUMULATIVE
PROJECT: PART:
NOTES:
1.0 18 OF 24N/A MMWWW.PRECISION-DEVICES.COM
9. Horn Brace 2
762
.19
44.03°
303
.16
17.
74°
453
.51
458
.46 467
.19
100
380
100 100
100
260
100
R48
308
.75
50
A
R9 Radius applied to edge onboth sides.
102
.88°
18.46
118
.23°
DETAIL A SCALE 1 : 2
DRAWN
NAME
TITLE:
DWG NO.
HS2-HORN-BRACE 2
Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.comwww.precision-devices.com
MM1.0NOTES:
PART:PROJECT:
LATIVE - CUMUONE +0.1/-0.0, NOLESH ± 0.4, INEAR LOLERANCET
DIMENSIONS:SCALE: SHEET:REVISION:
PD-H2-118S
021117
TITLE:
Precision Devices International Ltd. We operate a policy of continuous research and development and as such published speci�cations are subject to change without notice. 18mm Ply.
140318
© 2017, Precision Devices International Ltd. We operate a policy of continuous research and development and as such published specifications are subject to change without notice. Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.com
PD-H2-118SREVISION: SHEET:SCALE: DIMENSIONS:
TOLERANCE LINEAR ± 0.4, HOLES +0.1/-0.0, NONE - CUMULATIVE
PROJECT: PART:
NOTES:
1.0 19 OF 24N/A MMWWW.PRECISION-DEVICES.COM
10. Baffle Slot Port
534
524
.94
534
R207
385.87
150
264
18
189
534
524
.94
77.12°
74.65° 1
8
A
18 5
DETAIL A SCALE 1 : 2
DRAWN
NAME
TITLE:
DWG NO.
H2-118S Gsket Slot
Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.comwww.precision-devices.com
MM1.0NOTES:
PART:PROJECT:
LATIVE - CUMUONE +0.1/-0.0, NOLESH ± 0.4, INEAR LOLERANCET
DIMENSIONS:SCALE: SHEET:REVISION:
PD-H2-118S
021117
TITLE:
Precision Devices International Ltd. We operate a policy of continuous research and development and as such published speci�cations are subject to change without notice.
18mm Ply.
140318
© 2017, Precision Devices International Ltd. We operate a policy of continuous research and development and as such published specifications are subject to change without notice. Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.com
PD-H2-118SREVISION: SHEET:SCALE: DIMENSIONS:
TOLERANCE LINEAR ± 0.4, HOLES +0.1/-0.0, NONE - CUMULATIVE
PROJECT: PART:
NOTES:
1.0 20 OF 24N/A MMWWW.PRECISION-DEVICES.COM
11. Horn Section 1
18
73.
62
55
73.
62
55
534
18
A
A
5
SECTION A-A
SCALE 1 : 1
DRAWN
NAME
TITLE:
DWG NO.
HS-HORN-1
Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.comwww.precision-devices.com
MM1.0NOTES:
PART:PROJECT:
LATIVE - CUMUONE +0.1/-0.0, NOLESH ± 0.4, INEAR LOLERANCET
DIMENSIONS:SCALE: SHEET:REVISION:
PD-H2-118S
021117
TITLE:
Precision Devices International Ltd. We operate a policy of continuous research and development and as such published speci�cations are subject to change without notice.
18mm Ply.
140318
© 2017, Precision Devices International Ltd. We operate a policy of continuous research and development and as such published specifications are subject to change without notice. Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.com
PD-H2-118SREVISION: SHEET:SCALE: DIMENSIONS:
TOLERANCE LINEAR ± 0.4, HOLES +0.1/-0.0, NONE - CUMULATIVE
PROJECT: PART:
NOTES:
1.0 21 OF 24N/A MMWWW.PRECISION-DEVICES.COM
12. Horn Section 2
391
.35
534
18
267
18
534
18
5 258
18
391
.35
44°
99°
407
.17
DRAWN
NAME
TITLE:
DWG NO.
HS2-HORN-2
Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.comwww.precision-devices.com
MM1.0NOTES:
PART:PROJECT:
LATIVE - CUMUONE +0.1/-0.0, NOLESH ± 0.4, INEAR LOLERANCET
DIMENSIONS:SCALE: SHEET:REVISION:
PD-H2-118S
021117
TITLE:
Precision Devices International Ltd. We operate a policy of continuous research and development and as such published speci�cations are subject to change without notice. 18mm Ply.
140318
© 2017, Precision Devices International Ltd. We operate a policy of continuous research and development and as such published specifications are subject to change without notice. Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.com
PD-H2-118SREVISION: SHEET:SCALE: DIMENSIONS:
TOLERANCE LINEAR ± 0.4, HOLES +0.1/-0.0, NONE - CUMULATIVE
PROJECT: PART:
NOTES:
1.0 22 OF 24N/A MMWWW.PRECISION-DEVICES.COM
13. Horn Section 3
319.77
534
534
18
5
A
319.77
18
77° 99°
5 18 DETAIL A
SCALE 1 : 1
DRAWN
NAME
TITLE:
DWG NO.
HS2-HORN-3
Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.comwww.precision-devices.com
MM1.0NOTES:
PART:PROJECT:
LATIVE - CUMUONE +0.1/-0.0, NOLESH ± 0.4, INEAR LOLERANCET
DIMENSIONS:SCALE: SHEET:REVISION:
PD-H2-118S
021117
TITLE:
Precision Devices International Ltd. We operate a policy of continuous research and development and as such published speci�cations are subject to change without notice.
18mm Ply.
140318
© 2017, Precision Devices International Ltd. We operate a policy of continuous research and development and as such published specifications are subject to change without notice. Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.com
PD-H2-118SREVISION: SHEET:SCALE: DIMENSIONS:
TOLERANCE LINEAR ± 0.4, HOLES +0.1/-0.0, NONE - CUMULATIVE
PROJECT: PART:
NOTES:
1.0 23 OF 24N/A MMWWW.PRECISION-DEVICES.COM
14. Driver Mounting Baffle
492
.33
501
.38
534
41
4
15°
45
6
241
.47
18mm Recess x 3mm Deep to take M8 T-NUT
X 6 M8 T-NUT equispaced on 456mm PCD
492
.33
77.12°
501
.38
74.
65°
DRAWN
NAME
TITLE:
DWG NO.
H2-118S Speaker Gasket
Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.comwww.precision-devices.com
MM1.0NOTES:
PART:PROJECT:
LATIVE - CUMUONE +0.1/-0.0, NOLESH ± 0.4, INEAR LOLERANCET
DIMENSIONS:SCALE: SHEET:REVISION:
PD-H2-118S
021117
TITLE:
Precision Devices International Ltd. We operate a policy of continuous research and development and as such published speci�cations are subject to change without notice.
18mm Ply.
140318
© 2017, Precision Devices International Ltd. We operate a policy of continuous research and development and as such published specifications are subject to change without notice. Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.com
PD-H2-118SREVISION: SHEET:SCALE: DIMENSIONS:
TOLERANCE LINEAR ± 0.4, HOLES +0.1/-0.0, NONE - CUMULATIVE
PROJECT: PART:
NOTES:
1.0 24 OF 24N/A MMWWW.PRECISION-DEVICES.COM
15. Driver Access Panel
286
506
R28
10
80.50 105
105
105
105
105
266
286
18
19
9
248
286 5
06
19
R9
468
DRAWN
NAME
TITLE:
DWG NO.
HS2-118s door
Plans are provided free of charge for non-commercial purposes. For commercial licensing please contact us at [email protected] or via our website www.precision-devices.comwww.precision-devices.com
MM1.0NOTES:
PART:PROJECT:
LATIVE - CUMUONE +0.1/-0.0, NOLESH ± 0.4, INEAR LOLERANCET
DIMENSIONS:SCALE: SHEET:REVISION:
PD-H2-118S
021117
TITLE:
Precision Devices International Ltd. We operate a policy of continuous research and development and as such published speci�cations are subject to change without notice.18mm Ply.