parts, service & accessories corolla hatch

Do not slam bonnet.

Installation Time: Approx. 15 mins

Place these instructions in vehicle’s glove box after installation is complete

Accessory Part No. PZQ14-12170

July 2018 Production Onwards ACRYLIC HEADLAMP COVERS

COROLLA HATCH

Installation Instructions

Clean Headlamp Coverswith a mild detergent and water solution.

Care Instructions:

ISSUE 1: 08/05/2018 of 6Accessory Part No. PZQ14-12170

Do not use automaticcar wash.

Do not use abrasive,spirit or solvent based cleaners.

PARTS, SERVICE & ACCESSORIES

H4427

Alcohol Wipe

Fitting Instruction Flyer

1 PZQ14-12170

PZQ14-1217A2

Qty Part numberItem Component Name

Headlamp Covers Set

Top Metal Clip Outer 2

Top Metal Clip Inner 2

Bottom Metal Inner “I” 2

Bottom Metal Outer “O” 2

Washer 8

Screw 8

Anti-Abrasive Tape 8

1

1

1

H4427

ISSUE 1: 08/05/2018 Accessory Part No. PZQ14-12170 of 6

COROLLA HATCH ACRYLIC HEADLAMP COVERS Accessory Part No. PZQ14-12170

LHS PART IS MIRROR IMAGE

PZQ14-1217AFITTING KIT

QtyItem 2 Top Metal Clip OuterA 2B 2C

D 2

Top Metal Clip Inner

QtyItem

Bottom Metal Clip Inner “I”

8Anti-Abrasive Tape

F 8

Alcohol WipeBottom Metal Clip Outer “O”

E 8 Washer

ScrewG

1H 1I Fitting Instruction Flyer

E F G H I

A C DBLive a Genuine Life

www.toyotamanuals.com.au/accessories

T201

5-00

0689

PS

A00

680

TOY

001

Congratulations on purchasing your Toyota Genuine Accessory.

Correct installation of your Accessory is critical to ensuring its performance and safeoperation. Before commencing installation, please consider if you have the appropriatetechnical skills to successfully install this product.

Fitting instructions are available on the Toyota Service Information & Repair Manualswebsite at www.toyotamanuals.com.au/accessories.

To view or download fitting instructions, enter the Accessory part number without the dash.The part number is found on the barcode label located on the outside of the Accessorypackaging as shown below.

Please follow the fitting instructions closely using the tools specified. If cutting or drillingtemplates are required, set the page scale to “none” in the print menu prior to printing.Always confirm the template size by measuring the scale indicator before cutting or drilling.

To the extent permitted by law, Toyota Australia excludes all liability which may arise becausea user of this publication fails to follow directions in the publication.

If you have any queries regarding the installation of your Toyota Genuine Accessory, please

S U R F A C E C L E A N E R

Read installation instructionsbefore use.

For use in cleaning painted metal,glass and other vehicle surfaces.

IMPREGNATED WITH 70% ISOPROPYL ALCOHOL

!DANGER

A U T O M O T I V E

EXPLODED VIEW A

EXPLODED VIEW C

EXPLODED VIEW D

EXPLODED VIEW B

HEADLAMP COVERPZQ14-12170

I o

I

o

1. Read installation instructions thoroughly before commencing installation. Open the bonnet and thoroughly clean and dry headlamps and surrounding areas. See Dia #1.

2. Trial fit the Headlamp Cover centrally on the headlamp.

Note the hole and slot at the top of the Headlamp Cover and mark this location onto the headlamp assembly.

Note the holes at the bottom of the Headlamp Cover and mark these locations onto the headlamp assembly and bumper directly below the holes. See Dia #2.

Note: Use a Non-Permanent Marker.

3. At the previously noted and marked locations, clean the headlamp lens with the alcohol wipe provided. Remove any residue with a clean dry cloth.

Fit the Headlamp Cover centrally on the headlamp, holding it approximately 1-2cm off the headlamp surface.

Adhere the anti-abrasive tapes provided to all slot and hole positions. Approximately two thirds of the anti-abrasive tape should be on the headlight surface. See Dia #3.

4. At the previously noted and marked top slot position, fit the top metal clip outer to the top of the headlamp.

H4427


COROLLA HATCH ACRYLIC HEADLAMP COVERSAccessory Part No. PZQ14-12170

Diagram #: 1

Diagram #: 2

Diagram #: 3

Diagram #: 4

A. Install the clip at an angle and engage the barbs.

B. Press the rear of the clip down flat.You will hear a “snap” when the clip is installed correctly.

Check: - the clip is flat to the headlamp top profile. - the barb of the clip is engaged to the lamp bucket. - the metal clip is located on the anti-abrasive tape and not on the headlamp lens. See Dia #4.

S U R F A C E C L E A N E R

Read installation instructionsbefore use.

For use in cleaning painted metal,glass and other vehicle surfaces.

IMPREGNATED WITH 70% ISOPROPYL ALCOHOL

!DANGER

A U T O M O T I V E

B

A

CONTACT

PRESS

Diagram #: 5

Diagram #: 6

Diagram #: 7

H4427



5. At the previously noted and marked top hole position, fit the top metal clip inner to the top of the headlamp by sliding the end of the clip underneath the front fascia.

Ensure that the metal clip is located on the anti-abrasive tape and not on the headlamp lens. See Dia #5.

6. At the previously noted position, fit the bottom metal outer clip “O” between the bumper and headlight assembly.

Ensure that the metal clip is located on the anti-abrasive tape and not on the headlight lens.See Dia #6.

7. At the previously noted position, fit the bottom metal inner clip “I” between the bumper and headlight assembly.

Ensure that the metal clip is located on the anti-abrasive tape and not on the headlight lens.See Dia #7.

I

o“O”

“I”

Diagram #: 8

Diagram #: 9

Diagram #: 10

Diagram #: 11

H4427



8. Loosely secure the Headlamp Cover to the two bottom metal clips and top metal clips with the screws and washers provided.See Dia #8.

9. Tighten the two bottom screws to the specified torque setting.See Dia #9.

Note: Ensure torque setting 0.5~0.8Nm is used.

10. Tighten the screw at the top metal outer clip location to the specified torque setting, while applying upwards pressure to the Headlamp Cover.See Dia #10.


11. Ensure the top outer screw is as close to the bottom of the vertical Headlight Protector slot as possible.See Dia #11.

Torque: 0.5~0.8 Nm

Torque: 0.5~0.8 Nm

Diagram #: 12

H4427



12. Tighten the screw at the top metal inner clip location to the specified torque setting.See Dia #12.


IMPORTANT: Conduct final inspection, ensuring all screws are tightened, and clips are correctly installed and not touching the headlamp surface.

TO REMOVE : Remove screws and washers, then removeHeadlamp Cover from the Headlamp Assembly.

Torque: 0.5~0.8 Nm

parts, service & accessories corolla hatch

Documents