panasonic nx5 multi-voltage photoelectric … hermetically sealed output relay significantly ....
TRANSCRIPT
401
Related Information
Selection Guide
Amplifier Built-in
Power Supply Built-in
Amplifier-separated
NX5
FIBERSENSORS
LASERSENSORS
PHOTOELECTRICSENSORS
MICROPHOTOELECTRIC
SENSORS
AREASENSORS
LIGHT CURTAINS /SAFETY
COMPONENTSPRESSURE /
FLOWSENSORS
INDUCTIVEPROXIMITY
SENSORS
PARTICULARUSE SENSORS
SENSOROPTIONS
SIMPLEWIRE-SAVING
UNITS
WIRE-SAVING SYSTEMS
MEASUREMENTSENSORS
STATIC ELECTRICITYPREVENTION
DEVICES
LASERMARKERS
PLC
HUMAN MACHINE INTERFACES
ENERGY CONSUMPTION VISUALIZATION COMPONENTS
FA COMPONENTS
MACHINE VISION SYSTEMS
UV CURING SYSTEMS
Interferenceprevention
Conforming to Low Voltageand EMC Directive
Multi-voltage
Multi-voltageThe NX5 series can operate at 24 to 240 V AC or 12 to 240 V DC, which is suitable for supply voltages around the world.
Direct hook-up to an AC power supply
No need to arrange a DC power supply.
Compact sizeDespite of being multi-voltage, it has a depth of just 35 mm 1.378 in.(W18 × H62 × D35 mm W0.709 × H2.441 × D1.378 in)
Conventional model Compared to theconventional modelDepth: 1/2Width: 2/3Volume: 1/3
NX5
Long sensing rangeIt is most suitable for conveyor lines and parking lot applications.
30 m 98.425 ft (Infrared LED)
700 mm 27.559 in(Infrared LED)
Thru-beam
7 m 22.966 ft (Infrared LED)
10 m 32.808 ft (Red LED)
5 m 16.404 ft(Red LED with polarizing filters)
Retroreflective
Diffuse reflective
High reliabilityIt has an IP66 protection. Moderate dust or water splashes will not affect the sensor.The hermetically sealed output relay significantly increases its reliability.
Hermetically sealed relay eliminates worries about bad contact
BASIC PERFORMANCE
FUNCTIONS / MOUNTINGEasy alignmentThe 10 m 32.808 ft thru-beam type sensor and the 5 m 16.404 ft retroreflective type sensor incorporate a red LED beam source. Beam alignment can be attained by checking the emitted beam visually.
Interference preventionTwo sensors can operate normally even if mounted close together.(Excluding the 30 m 98.425 ft thru-beam type sensor)
Multi-voltage photoelectric sensorusable worldwide
Compact Multi-voltage Photoelectric Sensor Power Supply Built-in
NX5 SERIES General terms and conditions ............. F-7 Sensor selection guide ................. P.271~
Glossary of terms / General precautions .......P.1455~ / P.1458~ China’s CCC mark ........................ P.1505
* 5 m 16.4041 ft cable length type: Certified (for sales in China only)
Certified
*
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]
Compact Multi-voltage Photoelectric Sensor NX5 SERIES 402
Selection GuideAmplifier Built-inPower Supply Built-inAmplifier-separated
NX5
FIBERSENSORS
LASERSENSORS
PHOTO-ELECTRICSENSORSMICROPHOTO-ELECTRICSENSORS
AREASENSORS
LIGHTCURTAINS /SAFETYCOMPONENTSPRESSURE / FLOWSENSORS
INDUCTIVEPROXIMITYSENSORS
PARTICULARUSE SENSORS
SENSOROPTIONS
SIMPLEWIRE-SAVINGUNITS
WIRE-SAVING SYSTEMS
MEASURE-MENTSENSORSSTATIC ELECTRICITYPREVENTIONDEVICES
LASERMARKERS
PLC
HUMAN MACHINE INTERFACESENERGY CONSUMPTION VISUALIZATION COMPONENTS
FA COMPONENTS
MACHINE VISION SYSTEMS
UV CURING SYSTEMS
ORDER GUIDE
Type Appearance Sensing range Model No.(Note 2, 3)
Emittingelement Output
Thru
-bea
m
Ligh
t-O
N
10 m 32.808 ftNX5-M10RA
Red LED
Relay contact 1c
Dar
k-O
N NX5-M10RB
Long
sen
sing
rang
e
Ligh
t-O
N
30 m98.425 ft
NX5-M30AInfrared LED
Dar
k-O
N NX5-M30B
Ret
rore
flect
ive
With
pol
ariz
ing
filte
rs
Ligh
t-O
N
0.1 to 5 m 0.328 to 16.404 ft(Note 1)
NX5-PRVM5ARed LED
Dar
k-O
N NX5-PRVM5B
Long
sen
sing
rang
e
Ligh
t-O
N
0.1 to 7 m 0.328 to 22.966 ft(Note 1)
NX5-RM7AInfrared LED
Dar
k-O
N NX5-RM7B
Diff
use
refle
ctiv
e
Ligh
t-O
N
700 mm 27.559 inNX5-D700A
Infrared LED
Dar
k-O
N NX5-D700B
Thru-beam type Retroreflective type Diffuse reflective type
NX5-M10RA and NX5-M30A(Light-ON)
NX5-PRVM5A and NX5-RM7A(Light-ON)
NX5-D700B(Dark-ON)
Notes: 1) The sensing range of the retroreflective type sensor is specified for the RF-230 reflector. Further, the sensing range is the possible setting range for the reflector. The sensor can detect an object less than 0.1 m 0.328 ft away.
0.1 m 0.328 ft
Sensor
Reflector
Reflector cannot beplaced in this range
Reflector
5 m 16.404 ft(NX5-RM7: 7 m 22.966 ft)
Setting rangeof the reflector
Actual sensing rangeof the sensor
2) The model No. with “P” shown on the label affixed to the thru-beam type sensor is the emitter, “D” shown on the label is the receiver.
3) Light-ON type sensor (model No. with suffix “A”) and Dark-ON type sensor (model No. with suffix “B”) are available in the NX5 series.For the following models, in case of power off, the output relay condition is the same as when an object is detected. (In case of power supply line disconnection, the output operation is the same as when an object is detected.) Refer to ‘‘I/O CIRCUIT DIAGRAM AND OUTPUT OPERATION (p.405)’’ for the output operation of each model.
5 m 16.404 ft cable length type5 m 16.404 ft cable length type (standard: 2 m 6.562 ft) is also available.When ordering this type, suffix “-C5” to the model No.(e.g.) 5 m 16.404 ft cable length type of NX5-M10RA is “NX5-M10RA-C5”.
Accessory• RF-230 (Reflector)
NOTE: Mounting bracket is not supplied with the sensor. Please select from the range of optional sensor mounting brackets (three types).
APPLICATIONS
Detecting car position at parking garage Detecting objects on conveyor line
Foot biangled mountingbracket
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]
403 Compact Multi-voltage Photoelectric Sensor NX5 SERIES
Selection Guide
Amplifier Built-in
Power Supply Built-in
Amplifier-separated
NX5
FIBERSENSORS
LASERSENSORS
PHOTO-ELECTRICSENSORS
MICROPHOTO-
ELECTRICSENSORS
AREASENSORS
LIGHTCURTAINS /
SAFETYCOMPONENTS
PRESSURE / FLOW
SENSORS
INDUCTIVEPROXIMITY
SENSORS
PARTICULARUSE
SENSORS
SENSOROPTIONS
SIMPLEWIRE-SAVING
UNITS
WIRE-SAVING SYSTEMS
MEASURE-MENT
SENSORSSTATIC
ELECTRICITYPREVENTION
DEVICES
LASERMARKERS
PLC
HUMAN MACHINE
INTERFACESENERGY
CONSUMPTION VISUALIZATION COMPONENTS
FA COMPONENTS
MACHINE VISION
SYSTEMS
UV CURING
SYSTEMS
OPTIONS
Designation Model No. Description
Sensor mounting bracket
MS-NX5-1 Foot angled mounting bracket(The thru-beam type sensor needs two brackets.)
MS-NX5-2 Foot biangled mounting bracket (sensor protection bracket)(The thru-beam type sensor needs two brackets.)
MS-NX5-3 Back angled mounting bracket(The thru-beam type sensor needs two brackets.)
Slit maskFor thru-beamtype sensoronly
OS-NX5-3×6Slit size 3 × 6 mm0.118 × 0.236 in
Slit on one side
• Sensing range: 3 m 9.843 ft [NX5-M10R] 16 m 52.493 ft [NX5-M30]
• Min. sensing object: ø10 mm ø0.394 in [NX5-M10R]ø20 mm ø0.787 in [NX5-M30]
Slit on both sides• Sensing range: 1 m 3.281 ft [NX5-M10R]
6 m 19.685 ft [NX5-M30]• Min. sensing object: 3 × 6 mm 0.118 × 0.236 in
Interference prevention filter
For NX5-M10RAor NX5-M10RBonly
PF-NX5-V(Vertical,Silver) Same type of filters on both sides
• Sensing range: 5 m 16.404 ft• Min. sensing object: ø20 mm ø0.787 in
(One set consists of 2 pcs. of interference prevention filters.)PF-NX5-H(Horizontal, Light brown)
ReflectorFor retrore-flective typesensor only
RF-210• Sensing range: 0.1 to 1.5 m 0.328 to 4.921 ft [NX5-PRVM5]
0.1 to 2.5 m 0.328 to 8.202 ft [NX5-RM7]• Min. sensing object: ø30 mm ø1.181 in
RF-220• Sensing range: 0.1 to 3.5 m 0.328 to 11.483 ft [NX5-PRVM5]
0.1 to 5 m 0.328 to 16.404 ft [NX5-RM7]• Min. sensing object: ø35 mm ø1.378 in
Reflector mounting bracket
MS-RF21-1 Protective mounting bracket for RF-210It protects the reflector from damage and maintains alignment.
MS-RF22 For RF-220
MS-RF23 For RF-230
Reflective tapeFor retrore-flective typesensor only
RF-11• Ambient temperature:
–25 to +50 °C –13 to +122 °F• Ambient humidity: 35 to 85 % RH
Notes• Keep the tape free from stress.
If it is pressed too much, itscapability may deteriorate.
• Do not cut the tape. It will deteriorate the sensingperformance.
• Sensing range:0.1 to 0.8 m 0.328 to 2.625 ft
[NX5-PRVM5]0.1 to 1 m 0.328 to 3.281 ft
[NX5-RM7]
RF-12
• Sensing range:0.1 to 1 m 0.328 to 3.281 ft
[NX5-PRVM5]0.1 to 1.5 m 0.328 to 4.921 ft
[NX5-RM7]
Sensor checker(Note) CHX-SC2
It is useful for beam alignment of thru-beam type sensors.The optimum receiver position is given by indicators, aswell as an audio signal.
Note: Refer to p.980 for details of the sensor checker CHX-SC2.
Sensor mounting bracket• MS-NX5-1 • MS-NX5-2
Two M4 (length 25 mm 0.984 in) screws with washers and two M4 nuts are attached.
Two M4 (length 25 mm 0.984 in) screws with washers and two M4 nuts are attached.
Two M4 (length 25 mm 0.984 in) screws with washers and two M4 nuts are attached.
• MS-NX5-3
Slit mask• OS-NX5-3×6
Fitted on the front face of the sensor with one touch.
Interference prevention filter(For NX5-M10R only)
• PF-NX5-V(Vertical, Silver color)• PF-NX5-H(Horizontal, Light brown)
Two sets of thru-beam type sensors (Red LED type) can be mounted close together.
Reflector• RF-210 • RF-220
Reflective tape
Reflector mounting bracket• MS-RF23 • MS-RF22 • MS-RF21-1
Two M4 (length 10 mm 0.394 in) screws with washers are attached.
Two M3 (length 8 mm 0.315 in) screws with washers are attached.
Two M3 (length 12 mm 0.472 in) screws with washers are attached.
• RF-11 • RF-12
30 mm1.181 in
8 mm0.315 in
0.7 mm0.028 in
25 mm0.984 in
0.7 mm0.028 in
30 mm1.181 in
Sensor checker• CHX-SC2
LEVEL
POWER CHX-SC2
Sensor checker
33.3 mm1.311 in
12.8 mm0.504 in
11 mm0.433 in
35.3 mm1.390 in
8.3 mm0.327 in
42.3 mm1.665 in
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]
Compact Multi-voltage Photoelectric Sensor NX5 SERIES 404
Selection GuideAmplifier Built-inPower Supply Built-inAmplifier-separated
NX5
FIBERSENSORS
LASERSENSORS
PHOTO-ELECTRICSENSORSMICROPHOTO-ELECTRICSENSORS
AREASENSORS
LIGHTCURTAINS /SAFETYCOMPONENTSPRESSURE / FLOWSENSORS
INDUCTIVEPROXIMITYSENSORS
PARTICULARUSE SENSORS
SENSOROPTIONS
SIMPLEWIRE-SAVINGUNITS
WIRE-SAVING SYSTEMS
MEASURE-MENTSENSORSSTATIC ELECTRICITYPREVENTIONDEVICES
LASERMARKERS
PLC
HUMAN MACHINE INTERFACESENERGY CONSUMPTION VISUALIZATION COMPONENTS
FA COMPONENTS
MACHINE VISION SYSTEMS
UV CURING SYSTEMS
SPECIFICATIONS
TypeThru-beam Retroreflective
Diffuse reflectiveLong sensing range With polarizing filters Long sensing range
Item Model No. NX5-M10RA NX5-M10RB NX5-M30A NX5-M30B NX5-PRVM5A NX5-PRVM5B NX5-RM7A NX5-RM7B NX5-D700A NX5-D700BSensing range 10 m 32.808 ft 30 m 98.425 ft 0.1 to 5 m 0.328 to 16.404 ft (Note 2) 0.1 to 7 m 0.328 to 22.966 ft (Note 2) 700 mm 27.559 in (Note 3)
Sensing object ø20 mm ø0.787 in or more opaque object (Note 4)
ø20 mm ø0.787 in or more opaque object (Completely beam interrupted object) (Note 4)
ø50 mm ø1.969 in or more opaque, translucent or specular object (Note 2, 5)
ø50 mm ø1.969 in or more opaque or translucent object (Note 2, 5)
Opaque, translucent or transparent object (Note 5)
Hysteresis – 15 % or less of operation distance (Note 3)
Repeatability (perpendicular to sensing axis) 0.1 mm 0.004 in or less 0.2 mm 0.008 in or less 0.3 mm 0.012 in or less
Supply voltage 24 to 240 V AC +10–15 % or 12 to 240 V DC +10
–15 % Ripple P-P 10 % or less
Power consumption Emitter: 1 VA or lessReceiver: 2 VA or less
Emitter: 1.5 VA or lessReceiver: 2 VA or less 2 VA or less
Output
Relay contact 1 c• Switching capacity: 250 V AC 1 A (resistive load)
30 V DC 2 A (resistive load)• Electrical life: 500,000 or more switching operations (switching frequency 3,600 operations/hour)
100,000 or more switching operations (switching frequency 3,600 operations/hour)• Mechanical life: 100 million or more switching operations (switching frequency 36,000 operations/hour)
Output operation Light-ON Dark-ON Light-ON Dark-ON Light-ON Dark-ON Light-ON Dark-ON Light-ON Dark-ON
Response time 10 ms or less
Operation indicator Red LED (lights up when the output is ON)
Stability indicator Green LED (lights up under stable light received condition or stable dark condition)
Power indicator – Red LED(lights up when the power is ON)
–
Sensitivity adjuster Continuously variable adjuster – Continuously variable adjuster – Continuously variable adjuster
Automatic interference prevention function
Use optional interferenceprevention filters
– Incorporated (Two units of sensors can be mounted close together.)
Env
ironm
enta
l res
ista
nce
Pollution degree 3 (Industrial environment)
Protection IP66 (IEC)
Ambient temperature –20 to +55 °C – 4 to +131 °F (No dew condensation or icing allowed) (Note 6), Storage: –30 to +70 °C –22 to +158 °F
Ambient humidity 35 to 85 % RH, Storage: 35 to 85 % RH
Ambient illuminance Incandescent light: 3,500 ℓx at the light-receiving face
EMC EN 61000-6-2, EN 61000-6-4
Voltage withstandability 1,500 V AC for one min. between power supply and output terminals, 1,000 V AC for one min. between relay contact terminals
Insulation resistance 20 MΩ, or more, with 500 V DC megger between power supply and output terminals, and between relay contact terminals
Vibration resistance 10 to 55 Hz frequency, 1.5 mm 0.059 in amplitude in X, Y and Z directions for two hours each
Shock resistance 500 m/s2 (50 G approx.) in X, Y and Z directions for three times each
Emitting element Red LED (modulated) Infrared LED (modulated) Red LED (modulated) Infrared LED (modulated)
Peak emission wavelength 660 nm 0.026 mil 880 nm 0.035 mil 660 nm 0.026 mil 880 nm 0.035 mil
Material Enclosure: Polycarbonate, Lens: Polycarbonate, Cover: Polycarbonate, Front cover (retroreflective type sensor only): Acrylic
Cable 0.3 mm2 5-core (thru-beam type emitter: 2-core) cabtyre cable, 2 m 6.562 ft long
Cable extension Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable (thru-beam type: both emitter and receiver).
Net weight Emitter: 100 g approx.Receiver: 140 g approx.
Emitter: 125 g approx.Receiver: 140 g approx. 140 g approx.
Accessories Adjusting screwdriver: 1 pc. – RF-230 (Reflector): 1 pc.Adjusting screwdriver: 1 pc. RF-230 (Reflector): 1 pc. Adjusting screwdriver: 1 pc.
Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 °C +73.4 °F. 2) The sensing range and the sensing object of the retroreflective type sensor is specified for the RF-230 reflector. Further, the sensing range is the
possible setting range for the reflector. The sensor can detect an object less than 0.1 m 0.328 ft away.
0.1 m 0.328 ft
Sensor
Reflector
Setting rangeof the reflector
Reflector cannot beplaced in this range
Reflector
Actual sensing rangeof the sensor
5 m 16.404 ft (NX5-RM7: 7 m 22.966 ft)
3) The sensing range and the hysteresis of the diffuse reflective type sensor are specified for white non-glossy paper (200 × 200 mm 7.874 × 7.874 in) as the object.
4) If slit masks (optional) are fitted, an object as small as 3 × 6 mm 0.118 × 0.236 in can be detected.5) Make sure to confirm detection with an actual sensor before use.6) In case the sensor is to be used at an ambient temperature of –15 °C +5 °F, or less, please contact our office.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]
405 Compact Multi-voltage Photoelectric Sensor NX5 SERIES
Selection Guide
Amplifier Built-in
Power Supply Built-in
Amplifier-separated
NX5
FIBERSENSORS
LASERSENSORS
PHOTO-ELECTRICSENSORS
MICROPHOTO-
ELECTRICSENSORS
AREASENSORS
LIGHTCURTAINS /
SAFETYCOMPONENTS
PRESSURE / FLOW
SENSORS
INDUCTIVEPROXIMITY
SENSORS
PARTICULARUSE
SENSORS
SENSOROPTIONS
SIMPLEWIRE-SAVING
UNITS
WIRE-SAVING SYSTEMS
MEASURE-MENT
SENSORSSTATIC
ELECTRICITYPREVENTION
DEVICES
LASERMARKERS
PLC
HUMAN MACHINE
INTERFACESENERGY
CONSUMPTION VISUALIZATION COMPONENTS
FA COMPONENTS
MACHINE VISION
SYSTEMS
UV CURING
SYSTEMS
I/O CIRCUIT DIAGRAM AND OUTPUT OPERATION
I/O circuit diagram
Color code
Brown
Blue
Black
Gray
White
Output relay
Supply voltage24 to 240 V AC %
or 12 to 240 V DC %
NO
NC
COM.
Internal circuit
Multi-voltagecircuit
Sen
sor c
ircui
t
+10–15
+10–15
Note: The emitter of the thru-beam type sensor has two wires for power (+V and 0 V) only.
SENSING CHARACTERISTICS (TYPICAL)
NX5-M30A NX5-M30B Thru-beam type
Parallel deviation Angular deviation Parallel deviation with slit masks (3 × 6 mm 0.118 × 0.236 in)
2,00078.740
1,00039.370
0 1,00039.370
2,00078.740
0
1032.808
2065.617
40131.234
3098.425
Emitter
Receiver
L
Left RightCenterOperational point ℓ (mm in)
Set
ting
dist
ance
L (m
ft)
ℓ
10 5 0 5 10
3098.425
40131.234
2065.617
1032.808
0
Left Right Center Operating angle θ ( ° )
Set
ting
dist
ance
L (m
ft)
Receiver
Emitter
L θ
60023.622
30011.811
0 30011.811
60023.622
0
516.404
1032.808
2065.617
1549.213
Set
ting
dist
ance
L (m
ft)
Slit onone side
Slit onboth sides
Left RightCenterOperating point ℓ (mm in)
Emitter
Receiver
L ℓ
1,00039.370
50019.685
0 50019.685
1,00039.370
0
1032.808
516.404
Emitter
Receiver
L
Left RightCenterOperational point ℓ (mm in)
Set
ting
dist
ance
L (m
ft)
ℓ
20 10 0 10 20 0
1032.808
516.404
(Down) Left
Horizontal direction
Vertical direction Receiver
Emitter
L
Right (Up) Center Operating angle θ ( ° )
Set
ting
dist
ance
L (m
ft)
θ
NX5-M10RA NX5-M10RB Thru-beam type
Parallel deviation Angular deviation Parallel deviation with slit masks (3 × 6 mm 0.118 × 0.236 in)
2007.874
1003.937
0 1003.937
2007.874
0
13.281
26.562
413.123
39.843 Slit on
one side
Slit onboth sides
Set
ting
dist
ance
L (m
ft)
Left RightCenterOperating point ℓ (mm in)
Emitter
Receiver
L ℓ
Output operation
Sensing modeThru-beam & Retroreflective type Diffuse reflective type
Light-ON (A) type Dark-ON (B) type Light-ON (A) type Dark-ON (B) type
Output NO(Black cable)
NC(Gray cable)
NO(Black cable)
NC(Gray cable)
NO(Black cable)
NC(Gray cable)
NO(Black cable)
NC(Gray cable)
Outpu
t con
dition Power OFF Open Close Open Close Open Close Open Close
Beam-received Close Open Open Close Close Open Open Close
Beam-interrupted Open Close Close Open Open Close Close Open
: Object detected state.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]
Compact Multi-voltage Photoelectric Sensor NX5 SERIES 406
Selection GuideAmplifier Built-inPower Supply Built-inAmplifier-separated
NX5
FIBERSENSORS
LASERSENSORS
PHOTO-ELECTRICSENSORSMICROPHOTO-ELECTRICSENSORS
AREASENSORS
LIGHTCURTAINS /SAFETYCOMPONENTSPRESSURE / FLOWSENSORS
INDUCTIVEPROXIMITYSENSORS
PARTICULARUSE SENSORS
SENSOROPTIONS
SIMPLEWIRE-SAVINGUNITS
WIRE-SAVING SYSTEMS
MEASURE-MENTSENSORSSTATIC ELECTRICITYPREVENTIONDEVICES
LASERMARKERS
PLC
HUMAN MACHINE INTERFACESENERGY CONSUMPTION VISUALIZATION COMPONENTS
FA COMPONENTS
MACHINE VISION SYSTEMS
UV CURING SYSTEMS
For plotting the left graph, the sensitivity has been set such that a 200 × 200 mm 7.874 × 7.874 in white non-glossy paper is just detectable at a distance of 700 mm 27.559 in.
SENSING CHARACTERISTICS (TYPICAL)
2007.874
1003.937
0 1003.937
2007.874
0
26.562
413.123
826.247
619.685
Sensor
L
Reflector(RF-230)
Set
ting
dist
ance
L (m
ft)
ℓ
Left RightCenterOperating point ℓ (mm in)
40 20 0 20 40
619.685
826.247
413.123
26.562
0
Left Right Center Operating angle θ ( ° )
Set
ting
dist
ance
L (m
ft)
Reflector angular deviation
Sensor angular deviation
Sensor angular deviation Reflector (RF-230)
Sensor Sensor
Reflector angular deviation Reflector (RF-230)
L L θ
θ
Retroreflective typeNX5-PRVM5A NX5-PRVM5B Retroreflective typeNX5-RM7A NX5-RM7B
Parallel deviation Angular deviation Parallel deviation Angular deviation
NX5-D700A NX5-D700B Diffuse reflective type
Sensing field Correlation between sensing object size and sensing range
As the sensing object size becomes smaller than the standard size (white non-glossy paper 200 × 200 mm 7.874 × 7.874 in), the sensing range shortens, as shown in the left graph.
2007.874
1003.937
0 1003.937
2007.874
0
Set
ting
dist
ance
L (m
ft)
Left RightCenterOperating point ℓ (mm in)
Sensor
L
Reflector(RF-230)
ℓ 2
6.562
413.123
826.247
619.685
40 20 0 20 40
619.685
826.247
413.123
26.562
0
Left Right Center Operating angle θ ( ° )
Set
ting
dist
ance
L (m
ft)
Reflector angular deviation
Sensor angular deviation
Sensor angular deviation Reflector (RF-230)
Sensor Sensor
Reflector angular deviation Reflector (RF-230)
L L θ
θ
401.575
200.787
0 200.787
401.575
0
2007.874
40015.748
80031.496
60023.622
L
Sensor
Set
ting
dist
ance
L (m
m in
)
ℓ
Left RightCenterOperating point ℓ (mm in)
200 × 200 mm7.874 × 7.874 inWhite non-glossy paper
0 2007.874
30011.811
40015.748
L
Sensor
Sen
sing
rang
e L
(mm
in)
White non-glossy paperside length a (mm in)
2007.874
40015.748
80031.496
60023.622
1003.937
a × a mma × a inWhite non-glossy paper
PRECAUTIONS FOR PROPER USE Refer to p.1458~ for general precautions.
Mounting• The tightening torque should be 0.8 N·m or less.
M4 (length 25 mm 0.984 in)screw with washers
Sensor mounting bracket (Optional)
M4 nuts
Others• Do not use during the initial transient time (50 ms) after
the power supply is switched on.• Although the protection degree is specified for the sensor
including the cable, the cable end is not waterproof, andis not covered by the protection specified. Hence, makesure that water does not seep in from the cable end.
Interference prevention filter (Exclusively for NX5-M10R)• Use the interference prevention filters (optional) when
two units of thru-beam type sensors are mounted closetogether. However, take note that the sensing range willbecome short.
Interference prevention filterFitted with PF-NX5-V(Vertical, Silver coior)
Interference prevention filterFitted with PF-NX5-H(Horizontal, Light brown)
Note: The filters cannot be used for NX5-M30A or NX5-M30B.
• Never use this product as a sensing devicefor personnel protection.
• In case of using sensing devices forpersonnel protection, use products whichmeet laws and standards, such as OSHA,ANSI or IEC etc., for personnel protectionapplicable in each region or country.
• There are 2 types of interference prevention filters. InstallPF-NX5-H (Horizontal, Light brown) for 1 set, and installPF-NX5-V (Vertical, Silver color) for the other set.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]
407 Compact Multi-voltage Photoelectric Sensor NX5 SERIES
Selection Guide
Amplifier Built-in
Power Supply Built-in
Amplifier-separated
NX5
FIBERSENSORS
LASERSENSORS
PHOTO-ELECTRICSENSORS
MICROPHOTO-
ELECTRICSENSORS
AREASENSORS
LIGHTCURTAINS /
SAFETYCOMPONENTS
PRESSURE / FLOW
SENSORS
INDUCTIVEPROXIMITY
SENSORS
PARTICULARUSE
SENSORS
SENSOROPTIONS
SIMPLEWIRE-SAVING
UNITS
WIRE-SAVING SYSTEMS
MEASURE-MENT
SENSORSSTATIC
ELECTRICITYPREVENTION
DEVICES
LASERMARKERS
PLC
HUMAN MACHINE
INTERFACESENERGY
CONSUMPTION VISUALIZATION COMPONENTS
FA COMPONENTS
MACHINE VISION
SYSTEMS
UV CURING
SYSTEMS
Retroreflective type sensor (NX5-RM7)• Please take care of the following points when detecting
materials having a gloss.
L
10° to 30°
Sensor
Glossysurface
Reflector
Sensingobject
Make L sufficiently long1 Make L, shown in the diagram,sufficiently long.
2 Install at an angle of 10 to 30 degrees to the sensing object.
* NX5-PRVM5 does not need the above adjustment.
Retroreflective type sensor with polarizing filters (NX5-PRVM5)
• If a shiny object is covered or wrapped with a transparentfilm, such as those described below, the retroreflectivetype sensor with polarizing filters may not be able todetect it.In that case, follow the steps given below.
Example of sensing objects• Can wrapped by clear film• Aluminum sheet covered by plastic film• Gold or silver color (specular) label or wrapping paper
Steps• Tilt the sensor with respect to the sensing object while
fitting.• Reduce the sensitivity.• Increase the distance between the sensor and the
sensing object.
DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from our website.
SensorNX5-M10RA NX5-M10RB NX5-M30A NX5-M30B
Beam axis
200.787
Stabilityindicator(Green) (Note 3) Operation indicator
(Red) (Note 1, 3)
Sensitivity adjuster (Note 2, 3)
351.378
622.441
501.969
40.157
2-ø4.5 ø0.177 mounting holes2-M4 nut seats (on both sides)
50.197
250.984
ø5.8 ø0.228 cable, 2 m 6.562 ft long
6 0.236
180.709
SensorNX5-PRVM5A NX5-PRVM5B NX5-RM7A NX5-RM7B
SensorNX5-D700A NX5-D700B
20.50.807
180.709 35
1.378
622.441
501.969
50.197
250.984
Stabilityindicator(Green)
Center ofsensing
Operation indicator(Red)
Sensitivity adjuster
2-ø4.5 ø0.177 mounting holes2-M4 nut seats (on both sides)
Beam-receiving part
Beam-emitting part
6 0.236
ø5.8 ø0.228 cable, 2 m 6.562 ft long
40.157
Notes: 1) It is the power indicator (red) on the emitter of NX5-M30.2) Not incorporated on NX5-M30.3) Not incorporated on the emitter.
Center ofsensing
20.50.807
Stabilityindicator(Green)
Operation indicator(Red)
Sensitivity adjuster (Note)
501.969
2-ø4.5 ø0.177 mounting holes2-M4 nut seats (on both sides)
50.197
250.984
Beam-receiving part
Beam-emitting part
622.441
351.378
6 0.236
ø5.8 ø0.228 cable, 2 m 6.562 ft long
40.157
180.709
Note: Not incorporated on NX5-RM7.
PRECAUTIONS FOR PROPER USE Refer to p.1458~ for general precautions.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]
Compact Multi-voltage Photoelectric Sensor NX5 SERIES 408
Selection GuideAmplifier Built-inPower Supply Built-inAmplifier-separated
NX5
FIBERSENSORS
LASERSENSORS
PHOTO-ELECTRICSENSORSMICROPHOTO-ELECTRICSENSORS
AREASENSORS
LIGHTCURTAINS /SAFETYCOMPONENTSPRESSURE / FLOWSENSORS
INDUCTIVEPROXIMITYSENSORS
PARTICULARUSE SENSORS
SENSOROPTIONS
SIMPLEWIRE-SAVINGUNITS
WIRE-SAVING SYSTEMS
MEASURE-MENTSENSORSSTATIC ELECTRICITYPREVENTIONDEVICES
LASERMARKERS
PLC
HUMAN MACHINE INTERFACESENERGY CONSUMPTION VISUALIZATION COMPONENTS
FA COMPONENTS
MACHINE VISION SYSTEMS
UV CURING SYSTEMS
Reflector (Optional)RF-210
33.31.311
ReflectorM3 nut mounting holes(for mounting at the back)
Base
250.984
3.20.126
100.394
2-ø3.4 ø0.134 thru-holes(for mounting at the side)
(for mounting at the back)
2-ø3.4 ø0.134 holes, 6 0.236 deep
(for mounting at the side)2-M3 nut mounting holes
12.8 0.504
11 0.433
Material: Acrylic (Reflector) ABS (Base)
Two M3 (length 8 mm 0.315 in)screws with washers and two nuts are attached.
Reflective tape (Optional)RF-11 Reflective tape (Optional)RF-12
80.315
281.102
301.181
Adhesivetape
Effective reflecting surface
0.70.028( )
( )60.236
( )
301.181
0.70.028
281.102
250.984
230.906
AdhesivetapeEffective
reflecting surface
( )
Material: Acrylic
2-ø4.6 ø0.181mountingholes
50.31.980
401.575
5 0.197
8.30.327
3.30.130
10 0.394
59.32.335
49.31.941
( )301.181
35.31.390
42.31.665
34.31.350
250.984
2-ø3.6 ø0.142mountingholes
4 0.1578 0.315
8.30.327
3.30.130
210.827( )
Material: Acrylic (Reflector) ABS (Base)
Material: Acrylic (Reflector) ABS (Base)
Reflector (Accessory for the retroreflective type sensor)RF-230 Reflector (Optional)RF-220
DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from our website.
Material: Flexible polyvinyl chloride
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]
409 Compact Multi-voltage Photoelectric Sensor NX5 SERIES
Selection Guide
Amplifier Built-in
Power Supply Built-in
Amplifier-separated
NX5
FIBERSENSORS
LASERSENSORS
PHOTO-ELECTRICSENSORS
MICROPHOTO-
ELECTRICSENSORS
AREASENSORS
LIGHTCURTAINS /
SAFETYCOMPONENTS
PRESSURE / FLOW
SENSORS
INDUCTIVEPROXIMITY
SENSORS
PARTICULARUSE
SENSORS
SENSOROPTIONS
SIMPLEWIRE-SAVING
UNITS
WIRE-SAVING SYSTEMS
MEASURE-MENT
SENSORSSTATIC
ELECTRICITYPREVENTION
DEVICES
LASERMARKERS
PLC
HUMAN MACHINE
INTERFACESENERGY
CONSUMPTION VISUALIZATION COMPONENTS
FA COMPONENTS
MACHINE VISION
SYSTEMS
UV CURING
SYSTEMS
MS-NX5-1 Sensor mounting bracket (Optional)
t 2t 0.079
9.4 0.370
5.20.205
6.40.252 25 0.984
120.472 22
0.866
ø6.4 ø0.252 hole
401.575
5°
5°4.5
0.177
501.969
150.591
301.181 72
2.835
250.984
60.236 25
0.984250.984
291.142
2-ø4.5 ø0.177 holes
R55.9R2.201
Assembly dimensionsMounting drawing with the receiver of NX5-M10R
10°
401.575
722.835
6.40.252 25
0.984
120.472 22
0.866
5.20.20521
0.82740
1.575(43)
(1.693)
ø6.4 ø0.252
512.008
t 2t 0.079
Beam axis
Material: Cold rolled carbon steel (SPCC) (Uni-chrome plated)
Two M4 (length 25 mm 0.984 in)screws with washers and two M4 nuts are attached.
Sensor mounting bracket (Optional)MS-NX5-2
Assembly dimensionsMounting drawing with the receiver of NX5-M10R
401.575
903.543
1044.094
60.236
6.40.252
10°
50.197
t 2t 0.079
140.551
250.984
Beam axis
562.205
60.236
250.984
702.756
t 2t 0.079
60.236
140.551
170.669
291.142
100.394
80.315
40 1.57537
1.45760.236
6.40.252
501.969
4.50.177
5°
5°15
0.59125
0.984
120.472
301.181
36.61.441
903.543
1044.094R28
R1.102
MS-NX5-3 Sensor mounting bracket (Optional)
t 2t 0.079
501.969
180.709
250.984
5.50.217
60.236
2-ø4.5 ø0.177 holes
4.50.177 5°
5°5.5
0.21725
0.984
451.772
301.181
501.969
642.520
220.866
120.472
9.50.374
6.40.252
50.197
60.236
421.654
6.40.252
6.40.252
R55.9R2.201
Assembly dimensionsMounting drawing with the receiver of NX5-M10R
10°
t 2t 0.079
451.772
642.520
210.827
6.40.252
180.709
60.236
6.40.252
401.575
100.394
50.19712
0.472
(43)(1.693)
Beam axis
220.866
421.654
DIMENSIONS (Unit: mm in)
Material: Cold rolled carbon steel (SPCC) (Uni-chrome plated)
Two M4 (length 25 mm 0.984 in) screws with washers andtwo M4 nuts are attached.
Material: Cold rolled carbon steel (SPCC) (Uni-chrome plated)
Two M4 (length 25 mm 0.984 in) screws with washers andtwo M4 nuts are attached.
The CAD data in the dimensions can be downloaded from our website.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]
Compact Multi-voltage Photoelectric Sensor NX5 SERIES 410
Selection GuideAmplifier Built-inPower Supply Built-inAmplifier-separated
NX5
FIBERSENSORS
LASERSENSORS
PHOTO-ELECTRICSENSORSMICROPHOTO-ELECTRICSENSORS
AREASENSORS
LIGHTCURTAINS /SAFETYCOMPONENTSPRESSURE / FLOWSENSORS
INDUCTIVEPROXIMITYSENSORS
PARTICULARUSE SENSORS
SENSOROPTIONS
SIMPLEWIRE-SAVINGUNITS
WIRE-SAVING SYSTEMS
MEASURE-MENTSENSORSSTATIC ELECTRICITYPREVENTIONDEVICES
LASERMARKERS
PLC
HUMAN MACHINE INTERFACESENERGY CONSUMPTION VISUALIZATION COMPONENTS
FA COMPONENTS
MACHINE VISION SYSTEMS
UV CURING SYSTEMS
DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from our website.
MS-RF22 Reflector mounting bracket for RF-220 (Optional)
Assembly dimensions
4.50.177
100.394
110.433
250.984
351.378
40.157
16 0.630
10 0.394
6 0.2368 0.315
441.732
200.787
t 1.6t 0.063
8-M3 × 0.5 0.020thru-hole threads
250.984
4.50.177
250.984
100.394 28.3
1.114
8.30.327
34.31.350
8 0.315
40.157
210.827
35.31.390
44.31.744
60.236
271.063
t 1.6t 0.063
19.30.760
( ) ( )
Material: Cold rolled carbon steel (SPCC) (Uni-chrome plated)
Two M3 (length 8 mm 0.315 in) screws with washers are attached.
MS-RF23 Reflector mounting bracket for RF-230 (Optional)
Assembly dimensions40
1.575 4.50.177
30.118 10
0.394 110.433
501.969
401.575
5 0.197
16 0.630
15 0.591
18 0.709
7 0.276
200.787
t 2t 0.079
8-M4 × 0.7 0.028 thru-hole threads
261.024
120.472
351.378
30.118
612.402
( )
( ) 281.102( )
401.5754.5
0.177
28.31.11419.3
0.760
8.30.327
100.394
50.31.980
49.31.941
50.197
t 2t 0.07910
0.394
301.181
61.32.413
70.276
371.457
401.575
( )( )
Material: Cold rolled carbon steel (SPCC) (Uni-chrome plated)
Two M4 (length 10 mm 0.394 in) screws with washers are attached.
MS-RF21-1 Reflector mounting bracket for RF-210 (Optional)
Assembly dimensions
12.5 0.492
t 1.2t 0.047
130.512
ø25ø0.984
160.63010
0.3943.50.1383.2
0.126
R7.5R0.295
250.984
461.811
20°
230.906
501.969
5.50.217
ø36ø1.417
30°
461.811 25
0.984
130.512
100.394
20°
501.969
ø36ø1.417
30°
230.9065.5
0.217
Material: Stainless steel (SUS304)
Two M3 (length 12 mm 0.472 in) screws with washers are attached.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]