panasonic dmc-fz200 p pc pu eb ee ef eg ep gc gk gn gt sg

ORDER NO. DSC1208028CEB26

Digital CameraModel No. DMC-FZ200P

DMC-FZ200PCDMC-FZ200PUDMC-FZ200EBDMC-FZ200EEDMC-FZ200EFDMC-FZ200EGDMC-FZ200EPDMC-FZ200GCDMC-FZ200GKDMC-FZ200GNDMC-FZ200GTDMC-FZ200SG

Colour(K)...........Black Type

© Panasonic Corporation 2012 Unauthorized copy-ing and distribution is a violation of law.

TABLE OF CONTENTSPAGE PAGE

1 Safety Precautions -----------------------------------------------31.1. General Guidelines ----------------------------------------31.2. Leakage Current Cold Check ---------------------------31.3. Leakage Current Hot Check (See Figure. 1)--------31.4. How to Discharge the E.Capacitor on Flash

P.C.B.----------------------------------------------------------42 Warning --------------------------------------------------------------5

2.1. Prevention of Electrostatic Discharge (ESD)to Electrostatically Sensitive (ES) Devices ----------5

2.2. How to Recycle the Lithium Ion Battery (U.S.Only)-----------------------------------------------------------5

2.3. Caution for AC Cord(For EB/GC) ----------------------62.4. How to Replace the Lithium Battery-------------------7

3 Service Navigation------------------------------------------------83.1. Introduction --------------------------------------------------83.2. Important Notice --------------------------------------------83.3. General Description About Lead Free Solder

(PbF) ----------------------------------------------------------93.4. How to Define the Model Suffix (NTSC or PAL

model)------------------------------------------------------- 104 Specifications ---------------------------------------------------- 145 Location of Controls and Components------------------ 166 Service Mode ----------------------------------------------------- 17

6.1. Error Code Memory Function ------------------------- 177 Service Fixture & Tools --------------------------------------- 20

7.1. Service Fixture and Tools ------------------------------ 207.2. When Replacing the Main P.C.B. -------------------- 217.3. Service Position ------------------------------------------ 21

8 Disassembly and Assembly Instructions --------------- 228.1. Disassembly Flow Chart-------------------------------- 228.2. P.C.B. Location ------------------------------------------- 228.3. Disassembly Procedure -------------------------------- 238.4. Lens Disassembly Procedure------------------------- 358.5. Removal of the MOS Unit ------------------------------ 42

9 Measurements and Adjustments -------------------------- 449.1. Introduction ------------------------------------------------ 449.2. Before Disassembling the unit ------------------------ 449.3. Details of Electrical Adjustment----------------------- 469.4. After Adjustment------------------------------------------ 50

10 Maintenance ------------------------------------------------------ 5110.1. Cleaning Lens, Viewfinder and LCD Panel -------- 51

11 Block Diagram --------------------------------------------------- 5211.1. Overall Block Diagram ---------------------------------- 5211.2. System Control Block Diagram ----------------------- 5311.3. Video/Audio Process Block Diagram---------------- 5411.4. Lens/Flash Block Diagram----------------------------- 5511.5. Power Block Diagram ----------------------------------- 56

12 Wiring Connection Diagram --------------------------------- 5712.1. Interconnection Diagram ------------------------------- 57

2

1 Safety Precautions1.1. General Guidelines

1. IMPORTANT SAFETY NOTICEThere are special components used in this equipmentwhich are important for safety. These parts are marked by

in the Schematic Diagrams, Circuit Board Layout,Exploded Views and Replacement Parts List. It is essen-tial that these critical parts should be replaced with manu-facturer’s specified parts to prevent X-RADIATION,shock, fire, or other hazards. Do not modify the originaldesign without permission of manufacturer.

2. An Isolation Transformer should always be used duringthe servicing of AC Adaptor whose chassis is not isolatedfrom the AC power line. Use a transformer of adequatepower rating as this protects the technician from acci-dents resulting in personal injury from electrical shocks. Itwill also protect AC Adaptor from being damaged by acci-dental shorting that may occur during servicing.

3. When servicing, observe the original lead dress. If a shortcircuit is found, replace all parts which have been over-heated or damaged by the short circuit.

4. After servicing, see to it that all the protective devicessuch as insulation barriers, insulation papers shields areproperly installed.

5. After servicing, make the following leakage currentchecks to prevent the customer from being exposed toshock hazards.

1.2. Leakage Current Cold Check1. Unplug the AC cord and connect a jumper between the

two prongs on the plug.2. Measure the resistance value, with an ohmmeter,

between the jumpered AC plug and each exposed metal-lic cabinet part on the equipment such as screwheads,connectors, control shafts, etc. When the exposed metal-lic part has a return path to the chassis, the readingshould be between 1 MΩ and 5.2 MΩ. When the exposedmetal does not have a return path to the chassis, thereading must be infinity.

1.3. Leakage Current Hot Check(See Figure. 1)

1. Plug the AC cord directly into the AC outlet. Do not usean isolation transformer for this check.

2. Connect a 1.5 kΩ, 10 W resistor, in parallel with a 0.15 μFcapacitor, between each exposed metallic part on the setand a good earth ground, as shown in Figure. 1.

3. Use an AC voltmeter, with 1 kΩ/V or more sensitivity, tomeasure the potential across the resistor.

4. Check each exposed metallic part, and measure the volt-age at each point.

5. Reverse the AC plug in the AC outlet and repeat each ofthe above measurements.

6. The potential at any point should not exceed 0.75 V RMS.A leakage current tester (Simpson Model 229 or equiva-lent) may be used to make the hot checks, leakage cur-rent must not exceed 1/2 mA. In case a measurement isoutside of the limits specified, there is a possibility of ashock hazard, and the equipment should be repaired andrechecked before it is returned to the customer.

Figure. 1

3

1.4. How to Discharge the E.Capacitor on Flash P.C.B.CAUTION:

1. Be sure to discharge the E.Capacitor on FLASH P.C.B..2. Be careful of the high voltage circuit on FLASH P.C.B. when servicing.

[Discharging Procedure]1. Refer to the disassemble procedure and remove the necessary parts/unit.2. Install the insulation tube onto the lead part of resistor (ERG5SJ102:1kΩ /5W).

(An equivalent type of resistor may be used.)3. Place a resistor between both terminals of E.Capacitor on the FLASH P.C.B. for approx. 5 seconds.4. After discharging, confirm that the E.Capacitor voltage is lower than 10V by using a voltmeter.

Fig. F1

4

2 Warning2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically

Sensitive (ES) DevicesSome semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-trostatically Sensitive (ES) Devices.

The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge(ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on yourbody by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-num foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.4. Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" can

generate electrical charge sufficient to damage ES devices.5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most

replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-ble conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective materialto the chassis or circuit assembly into which the device will be installed.CAUTION :

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the

brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) suf-ficient to damage an ES device).

2.2. How to Recycle the Lithium Ion Battery (U.S. Only)

5

2.3. Caution for AC Cord(For EB/GC)

2.3.1. Information for Your SafetyIMPORTANT

Your attention is drawn to the fact that recording of pre-recorded tapes or discs or other published or broadcastmaterial may infringe copyright laws.

WARNINGTo reduce the risk of fire or shock hazard, do not exposethis equipment to rain or moisture.

CAUTIONTo reduce the risk of fire or shock hazard and annoyinginterference, use the recommended accessories only.

FOR YOUR SAFETY DO NOT REMOVE THE OUTER COVERTo prevent electric shock, do not remove the cover. No userserviceable parts inside. Refer servicing to qualified servicepersonnel.

2.3.2. Caution for AC Mains LeadFor your safety, please read the following text carefully.

This appliance is supplied with a moulded three-pin mains plugfor your safety and convenience.A 5-ampere fuse is fitted in this plug.Should the fuse need to be replaced please ensure that thereplacement fuse has a rating of 5 amperes and it is approvedby ASTA or BSI to BS1362.Check for the ASTA mark or the BSI mark on the body of thefuse.

If the plug contains a removable fuse cover you must ensurethat it is refitted when the fuse is replaced.If you lose the fuse cover, the plug must not be used until areplacement cover is obtained.A replacement fuse cover can be purchased from your localPanasonic Dealer.

If the fitted moulded plug is unsuitable for the socket outlet inyour home then the fuse should be removed and the plug cutoff and disposed of safety.There is a danger of severe electrical shock if the cut off plug isinserted into any 13-ampere socket.

If a new plug is to be fitted please observe the wiring code asshown below.If in any doubt, please consult a qualified electrician.

2.3.2.1. ImportantThe wires in this mains lead are coloured in accordance withthe following code:

As the colours of the wires in the mains lead of this appliancemay not correspond with the coloured markings identifying theterminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the ter-minal in the plug which is marked with the letter N or colouredBLACK.

The wire which is coloured BROWN must be connected to theterminal in the plug which is marked with the letter L or colouredRED.

Under no circumstances should either of these wires be con-nected to the earth terminal of the three pin plug, marked withthe letter E or the Earth Symbol.

2.3.2.2. Before UseRemove the Connector Cover as follows.

2.3.2.3. How to Replace the Fuse1. Remove the Fuse Cover with a screwdriver.

2. Replace the fuse and attach the Fuse cover.

Blue NeutralBrown Live

6

2.4. How to Replace the Lithium Battery2.4.1. Replacement Procedure

1. Remove the SUB P.C.B.. (Refer to Disassembly Procedures.)2. Remove the Lithium battery (Ref. No. “B9301” at foil side of SUB P.C.B.) and then replace it into new one.

NOTE:This Lithium battery is a critical component. (Type No.: ML614 Manufactured by Energy Company, Panasonic Corporation.)It must never be subjected to excessive heat or discharge.It must therefore only be fitted in requirement designed specifically for its use.Replacement batteries must be of same type and manufacture.They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.Do not attempt to re-charge the old battery or re-use it for any other purpose.It should be disposed of in waste products destined for burial rather than incineration.

NOTE:Above caution is applicable for a battery pack which is for DMC-FZ200 series, as well.

7

3 Service Navigation3.1. IntroductionThis service manual contains technical information, which allow service personnel’s to understand and service this model.Please place orders using the parts list and not the drawing reference numbers.If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.

3.2. Important Notice3.2.1. About lens block

• The image sensor (MOS) unit which are connected to the lens unit with 4 screws. These screws are locked with the screw lock-ing glue, after performing the Optical tilt adjustment. During servicing, if one of MOS unit fixing screws are loosened, the Optical tilt adjustment must be performed.(About the Optical tilt adjustment, refer to the “9.3.2. Adjustment Specifications” for details.)

NOTE:• It is necessary to use the “DSC_Tilt” software to allow the “Optical tilt adjustment”.• The Adjustment software “DSC_Tilt” is available at “TSN Website”.

3.2.2. About VENUS ENGINE(IC6001) [Located on the Main P.C.B.]:• The VENUS ENGINE (IC6001) consists of two IC chips, which are fixed together with solder.

(The so called, “Package On Package” type IC.)NOTE:

• During servicing, do not press down hard on the surface of IC6001.

3.2.3. About Flexible Cable and ConnectorDo not touch carelessly so that the foreign body should not adhere to the terminal part of flexible cable and connector.Wipe off with a clean cloth and the cotton bud, etc. when the terminal part is dirty.

8

3.3. General Description About Lead Free Solder (PbF)The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for thisequipment in considering the globally environmental conservation.The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30°C (86°F) more than that of thenormal solder.Distinction of P.C.B. Lead Free Solder being used

Service caution for repair work using Lead Free Solder (PbF)• The lead free solder has to be used when repairing the equipment for which the lead free solder is used.

(Definition: The letter of “PbF” is printed on the P.C.B. using the lead free solder.)• To put lead free solder, it should be well molten and mixed with the original lead free solder.• Remove the remaining lead free solder on the P.C.B. cleanly for soldering of the new IC.• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the

lead free solder.• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30°C

(662±86°F).Recommended Lead Free Solder (Service Parts Route.)

• The following 3 types of lead free solder are available through the service parts route.RFKZ03D01KS-----------(0.3mm 100g Reel)RFKZ06D01KS-----------(0.6mm 100g Reel)RFKZ10D01KS-----------(1.0mm 100g Reel)

Note* Ingredient: tin (Sn) 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%

9

3.4. How to Define the Model Suffix (NTSC or PAL model)There are eight kinds of DMC-FZ200.

• a) DMC-FZ200 (Japan domestic model), DMC-FZ200SG• b) DMC-FZ200P/PC• c) DMC-FZ200EB/EF/EG/EP• d) DMC-FZ200EE• e) DMC-FZ200GT• f) DMC-FZ200GK• g) DMC-FZ200GN• h) DMC-FZ200GC/PU

What is the difference is that the “INITIAL SETTINGS” data which is stored in Flash-ROM mounted on MAIN P.C.B..

3.4.1. Defining methods:To define the model suffix to be serviced, refer to the nameplate which is putted on the bottom side of the Unit.

NOTE:After replacing the MAIN P.C.B., be sure to achieve adjustment.The service software is available at “TSN Website”.

10

3.4.2. INITIAL SETTINGS:After replacing the MAIN P.C.B., make sure to perform the initial settings after achieving the adjustment by ordering the followingprocedure in accordance with model suffix of the unit.1. IMPORTANT NOTICE:

Before proceeding Initial settings, make sure to read the following CAUTIONS.

2. PROCEDURES:• Precautions: Read the above “CAUTION 1” and “CAUTION 2”, carefully.• Preparation:

- Attach the Battery or AC Adaptor with a DC coupler to the unit.(Since this unit has built-in memory, it can be performed without inserting SD memory card.)

- Remove the lens cap.• Step 1. The temporary cancellation of “INITIAL SETTINGS”:

Set the mode dial to “[ P ] (Program AE mode)”. While pressing “[ UP ] of Cursor button” and [ MOTION PICTURE ] button simultaneously, turn the Power on.

• Step 2. The cancellation of “INITIAL SETTINGS”:Press the [ PLAYBACK ] button, then playback the picture.Press “[ UP ] of Cursor button” and [ MOTION PICTURE ] button simultaneously, then turn the Power off.The LCD displays the “ ! ” mark before the unit powers down.

• Step 3. Turn the Power on:Set the mode dial to “[ P ] (Program AE mode)”, and then turn the Power on.

• Step 4. Display the INITIAL SETTING:While pressing [ MENU/SET ] and “[ RIGHT ] of Cursor buttons” simultaneously, turn the Power off. The “INITIAL SETTINGS” menu is displayed.There are two kinds of “INITIAL SETTINGS” menu form as follows:

11

[CASE 1. After replacing MAIN P.C.B.][Except “EG, EF, EB and EP” models: (VEP56170A is used as a Main P.C.B.)]When MAIN P.C.B. has just been replaced, all of the model suffix is displayed as follows. (Four pages in total)

[Only “EG, EF, EB and EP” models: (VEP56170B is used as a Main P.C.B.)]When MAIN P.C.B. has just been replaced, only 7 model suffix are displayed as follows. (Two pages in total)

[CASE 2. Other than “After replacing MAIN P.C.B.”]

• Step 5. Choose the model suffix in “INITIAL SETTINGS”: (Refer to “CAUTION 1”)[Caution: After replacing MAIN P.C.B.]

The model suffix can been chosen, JUST ONE TIME.Once one of the model suffix have been chosen, the model suffix lists will not be displayed, thus, it can not be changed.Therefore, select the area carefully.

Select the area with pressing “[ UP ] / [ DOWN ] of Cursor buttons”.

12

• Step 6. Set the model suffix in “INITIAL SETTINGS”: • Press the “[ RIGHT ] of Cursor buttons”.• The only set area is displayed, and then press the “[ RIGHT ] of Cursor buttons” after confirmation.

(The unit is powered off automatically.)

• Step 7. CONFIRMATION:Confirm the display of “PLEASE SET THE CLOCK” in concerned language when the unit is turned on again.When the unit is connected to PC with USB cable, it is detected as removable media.(When the “GT” or “GK” model suffix is selected, the display shows “PLEASE SET THE CLOCK” in Chinese.)

As for your reference, major default setting condition is as shown in the following table.• Default setting (After “INITIAL SETTINGS”)

MODEL VIDEO OUTPUT LANGUAGE DATE REMARKSa) DMC-FZ200 (Japan domestic model) NTSC Japanese Year/Month/Dateb) DMC-FZ200P NTSC English Month/Date/Yearc) DMC-FZ200PU NTSC Spanish Month/Date/Yeard) DMC-FZ200GC PAL English Date/Month/Yeare) DMC-FZ200GT NTSC Chinese (traditional) Year/Month/Datef) DMC-FZ200GK PAL Chinese (simplified) Year/Month/Dateg) DMC-FZ200EE PAL Russian Date/Month/Yearh) DMC-FZ200GN PAL English Date/Month/Yeari) DMC-FZ200PC NTSC English Month/Date/Yearj) DMC-FZ200EG PAL English Date/Month/Yeark) DMC-FZ200EF PAL French Date/Month/Yearl) DMC-FZ200EB PAL English Date/Month/Year

m) DMC-FZ200EP PAL English Date/Month/Yearn) DMC-FZ200SG PAL English Date/Month/Year

13

4 SpecificationsThe following specification is for DMC-FZ200P/DMC-FZ60P.Some specifications may differ depending on model suffix.

14

5 Location of Controls and ComponentsThe following description is for DMC-FZ200P/DMC-FZ60P.Some descriptions may differ depending on model suffix.

(DMC-FZ200) (DMC-FZ60)

MIC

REMOTE

1 2 43 5 6 8 119317 32

13 12

1910 3334

2126 14 35 15 16 17 3618 20

2223243738

28 29 30 39

27 25

1 2 43 5 6 7 8 109 11 12 13

40 4114 15 16 1718 19 20

21222324254226

28 29 30 43

27

1 Lens2 Zoom lever3 Shutter button4 [ ] (Burst Mode) button5 Self-timer indicator

AF Assist Lamp6 Mode dial7 Flash8 Lens barrel9 Diopter adjustment dial10 Speaker

Be careful not to cover the speaker withyour finger. Doing so may make sound difficult to hear.

11 Shoulder strap eyelet12 [HDMI] socket13 [AV OUT/DIGITAL] socket14 Viewfinder15 Stereo microphone16 Camera ON/OFF switch17 Motion picture button18 Power lamp19 [FOCUS] button20 Rear dial21 [DISP.] button22 [MENU/SET] button23 Cursor buttons24 [Q.MENU] button/

[ ] (Delete/Cancel) button25 [ ] (Playback) button26 [EVF/LCD] button27 LCD monitor28 Tripod mount

A tripod with a screw length of 5.5 mm(0.22 inch) or more may damage this unit if attached.

29 Release lever30 Card/Battery door

(DMC-FZ200)

31 Flash open leverTo close, push the top of the flash coveruntil it clicks.

32 [MIC/REMOTE] socket33 Focus selector switch34 Side lever35 Hot shoe36 [Fn1] button37 [Fn3] button38 [AF/AE LOCK] button/[Fn2] button39 DC coupler cover

When using an AC adaptor, ensure thatthe Panasonic DC coupler (DMW-DCC8: optional) and AC adaptor(DMW-AC8PP: optional) are used.Always use a genuine Panasonic AC adaptor (DMW-AC8PP: optional).

(DMC-FZ60)

40 Flash open button41 [AF/AF /MF] button42 [AF/AE LOCK] button/[Fn1] button43 DC coupler cover

When using an AC adaptor, ensure thatthe Panasonic DC coupler (DMW-DCC6: optional) and AC adaptor(DMW-AC8PP: optional) are used.Always use a genuine Panasonic AC adaptor (DMW-AC8PP: optional).

16

6 Service Mode6.1. Error Code Memory Function

1. General descriptionThis unit is equipped with history of error code memory function, and can be memorized 16 error codes in sequence from thelatest. When the error is occurred more than 16, the oldest error is overwritten in sequence.The error code is not memorized when the power supply is shut down forcibly (i.e.,when the unit is powered on by the battery,the battery is pulled out) The error code is memorized to FLASH-ROM when the unit has just before powered off.

2. How to displayThe error code can be displayed by ordering the following procedure:

• Preparation:- Attach the Battery or AC Adaptor with a DC coupler to the unit.

(Since this unit has built-in memory, it can be performed without inserting SD memory card.)- Remove the lens cap.

• Step 1. The temporary cancellation of “INITIAL SETTINGS”:Set the mode dial to “[ P ] (Program AE mode)”.While pressing “[ UP ] of Cursor button” and [ MOTION PICTURE ] button simultaneously, turn the Power on.

• Step 2. Execute the error code display mode:Press the “[ LEFT ] of Cursor button”, [ MENU/SET ] button and [ MOTION PICTURE ] button simultaneously.The display is changed as shown below when the above buttons are pressed simultaneously.Normal display → Error code display → Operation history display → Normal display → .....

Example of Error Code Display

17

3. Error Code ListThe error code consists of 8 bits data and it shows the following information.

18

Important notice about “Error Code List”1) About “*” indication:The third digit from the left is different as follows.

• In case of 0 (example: 18001000)When the third digit from the left shows “0”, this error occurred under the condition of INITIAL SETTINGS has been completed.It means that this error is occurred basically at user side.

• In case of 8 (example: 18801000)When the third digit from the left shows “8”, this error occurred under the condition of INITIAL SETTINGS has been released. (Example; Factory assembling-line before unit shipment, Service mode etc.)It means that this error is occurred at service side.

2) About “?” indication: (“18*0 0?01” to “18*0 0?50”):The third digit from the right shows one of the hexadecimal (“0” to “F”) character.

4. How to exit from Error Code display mode:Simply, turn the power off. (Since Error code display mode is executed under the condition of temporary cancellation of “INI-TIAL SETTINGS”, it wake up with normal condition when turn off the power.)NOTE:

The error code can not be initialized.

19

7 Service Fixture & Tools7.1. Service Fixture and ToolsThe following Service Fixture and tools are used for checking and servicing this unit.

20

7.2. When Replacing the Main P.C.B.After replacing the MAIN P.C.B., be sure to achieve adjustment.The service software is available at “TSN Website”.

7.3. Service PositionThis Service Position is used for checking and replacing parts. Use the following Extension cables for servicing.

Table S1 Extension Cable List

CAUTION-1. (When servicing FLASH P.C.B.)1. Be sure to discharge the E.Capacitor on FLASH P.C.B..

Refer to “HOW TO DISCHARGE THE E.CAPACITOR ON FLASH P.C.B.”.The E.Capacitor voltage is not lowered soon even if the AC Cord is unplugged or the battery is removed.

2. Be careful of the high voltage circuit on FLASH P.C.B..3. DO NOT allow other parts to touch the high voltage circuit on FLASH P.C.B..

No. Parts No. Connection Form1 VFK1906 PS9001 (MAIN) - PP8001 (FLASH) 20pin B to B

21

8 Disassembly and Assembly Instructions8.1. Disassembly Flow ChartThis is a disassembling chart.When assembling, perform this chart conversely.

8.2. P.C.B. Location

22

8.3. Disassembly Procedure

No. Item Fig Removal1 Rear Case Unit (Fig. D1) Card

Battery3 Screws (A)2 Screws (B)

(Fig. D2) Shoe Spring2 Screws (C)1 Locking tabFP9003 (Flex)Rear Case Unit

2 Rear Operation Unit (Fig. D3) 2 Screws (D)2 Hooking partsFP9007 (Flex)Rear Operation Unit

3 Main P.C.B. (Fig. D4) 1 Screw (E)FP9001 (Flex)FP9002 (Flex)FP9004 (Flex)FP9005 (Flex)FP9006 (Flex)FP9010 (Flex)PS9001 (Connector)Main P.C.B.1 Hooking partJack Holder

4 Top Operation Unit (Fig. D5) 1 Screw (F)Top Operation Unit

5 Battery Case Unit (Fig. D6) P8003 (Connector)P8004 (Connector)1 Screw (G)

(Fig. D7) Battery Case Unit6 Lens Unit (W/MOS) (Fig. D8) 4 Screws (H)

Lens Unit (W/MOS)7 EVF Unit & Flash Parts (Fig. D9) FP9302 (Flex)

2 ConvexesEVF Unit & Flash Parts

8 Sub P.C.B.Speaker

(Fig. D10) 1 Screw (I)FP9301 (Flex)1 Rib2 Hooking partsSub P.C.B.2 SoldersSpeaker

9 Side Switch Unit (Fig. D11) 1 Locking tabSide Frame (R)Strap Holder (R)1 Screw (J)2 Locking tabsFront Heat Sink3 Screws (K)

(Fig. D12) Lens Ring Front2 ConvexesSide Switch Unit

10 Flash P.C.B. (Fig. D13) 3 Locking tabsCondensor Cover

(Fig. D14) 2 Screws (L)2 Locking tabsFP8001 (Flex)Switch Unit1 Hooking partFlash P.C.B.

11 EVF Unit (Fig. D15) 2 Locking tabsEVF Unit

12 Hot Shoe UnitFlashMic FPC Unit

(Fig. D16) 1 Hooking part1 Screw (M)

(Fig. D17) 2 Screws (N)1 Screw (O)2 Locking tabsHot Shoe Unit2 Screws (P)

(Fig. D18) 4 Locking tabsFlash Case Top UnitFlash Shaft2 ConvexesFlash & Mic FPC Unit

(Fig. D19) 2 Locking tabsFlash Link Cover5 Ribs1 Positioning Pin2 Locking tabsFlash

(Fig. D20) Mic DamperMic FPC UnitMic Cushion

13 LCD PartsHinge SW FPC

(Fig. D21) 2 Screws (Q)2 Locking tabsHinge Arm Cover TopHinge Arm Cover Bottom2 Screws (R)Hinge Plate

(Fig. D22) Connector (A)3 RibsLCD Parts1 Screw (S)1 Locking tabRear Earth Plate B

(Fig. D23) 2 Hinge SW TapesHinge SW FPC

14 LCD Unit (Fig. D24) 2 Screws (T)2 Screws (U)6 Locking tabsLCD Case (Bottom)

(Fig. D25) Connector (B)LCD Hinge UnitLCD Case (Top)LCD Unit

No. Item Fig Removal

23

8.3.1. Removal of the Rear Case Unit

(Fig. D1)

(Fig. D2)

24

8.3.2. Removal of the Rear Operation Unit

(Fig. D3)

8.3.3. Removal of the Main P.C.B.

(Fig. D4)

25

8.3.4. Removal of the Top Operation Unit

(Fig. D5)

8.3.5. Removal of the Battery Case Unit

(Fig. D6)

(Fig. D7)

26

8.3.6. Removal of the Lens Unit (W/MOS)

(Fig. D8)

8.3.7. Removal of the EVF Unit & FlashParts

(Fig. D9)

27

8.3.8. Removal of the Sub P.C.B. andSpeaker

(Fig. D10)

8.3.9. Removal of the Side Switch Unit

(Fig. D11)

28

(Fig. D12)

8.3.10. Removal of the Flash P.C.B.

(Fig. D13)

29

(Fig. D14)

8.3.11. Removal of the EVF Unit

(Fig. D15)

8.3.12. Removal of the Hot Shoe Unit,Flash and Mic FPC Unit

(Fig. D16)

30

(Fig. D17)

(Fig. D18)

31

(Fig. D19)

(Fig. D20)

32

8.3.13. Removal of the LCD Parts andHinge SW FPC

(Fig. D21)(Fig. D22)

33

(Fig. D23)

8.3.14. Removal of the LCD Unit

(Fig. D24)

(Fig. D25)NOTE: (When Installing)

Make sure to confirm the following points when installing:• The screw is tightened enough.• Installing conditions are fine. (No distortion, no abnormal-

space.)• No dust and/or dirt on Lens surfaces.• LCD image is fine. (No dust and dirt on it, and no gradient

images.)

34

8.4. Lens Disassembly ProcedurePrecaution:

1. Do not remove the MOS unit when disassembling or re-assembling the lens in order to maintain it clean.The screws for fixing the MOS unit to the master flangeunit are locked by glue with the adjustment of the installa-tion angle of the MOS unit to the lens (optical axis adjust-ment) finished.When remove it, refer to item “8.5.”.

2. Keep dust or dirt away from the lens.To remove dirt or dust from the lens, blow with dry air.

3. Do not touch the lens surface.4. Use lens cleaning KIT (VFK1900BK).5. Apply grease as shown on item “8.4.8.” and “8.4.9.” in the

figure.

8.4.1. Removal of the Lens Flex Unit1. Unscrew the 2 screws (A).2. Remove the 10 Ribs.

3. Remove the 3 connector.4. Remove the lens flex unit.

8.4.2. Removal of the Master Flange Unit1. Unscrew the 3 screws (B).2. Remove the master flange unit.

35

8.4.3. Removal of the Zoom Motor1. Unscrew the 2 screws (C).

36

8.4.4. Removal of the 1st Lens Frame Unit1. Turn the cam frame in the direction of arrow fully, and

remove the 1st lens frame unit.

37

8.4.5. Removal of the 5th Lens Frame Unit1. Remove the 5th lens frame unit in the direction of arrow.

38

8.4.6. Removal of the 2nd Lens FrameUnit

1. Hold the middle frame unit, and turn the cam frame unit inthe direction of arrow (1) fully.(about half turn)

2. Reverse the cam frame, and remove the 2nd lens frameunit. (Catch the 2nd lens frame unit.)

39

8.4.7. Removal of the Cam Frame Unit1. Turn the cam frame unit in the direction of arrow (1)

fully.(about half turn)2. Move the 3rd lens frame unit to bottom. And turn the cam

frame unit in the direction of arrow (2) fully, and removethe cam frame unit.

40

8.4.8. Removal of the Focus Motor Unit1. Unscrew the 2 screws (D).2. Remove the focus motor unit.

(Also remove the flex from groove.)

8.4.9. Removal of the 4th and 3rd LensFrame Unit.

1. Remove the 4th lens frame unit and 3rd lens frame unitfrom middle frame unit.

41

8.5. Removal of the MOS UnitWhen remove the MOS unit once (the screw(E) is loosenedeven a little), the optical tilt adjustment is required.When loosen the screw(E), the optical tilt adjustment isnecessary at the end of assembling. (Refer to item “9.3.2.”)To prevent the MOS unit from catching the dust and dirt,do not remove the MOS unit except replacing it.

1. Unscrew the 4 screws(E).2. Remove the MOS unit.

42

9 Measurements and Adjustments9.1. IntroductionWhen servicing this unit, make sure to perform the adjustments necessary based on the part(s) replaced.Before disassembling the unit, it is recommended to back up the camera data stored in flash-rom as a data file. NOTE: (When replacing the Lens unit, Master flange unit and MOS unit)

• When the MOS unit is unavoidably removed for Lens unit, Master flange unit and MOS unit replaced, an optical adjustment isnecessary after parts are exchanged.

• It is necessary to use the “DSC_Tilt” software to allow the “Optical tilt adjustment”.• The Adjustment software “DSC_Tilt” is available at “TSN Website”.

9.2. Before Disassembling the unit9.2.1. Initial Setting ReleaseThe cameras specification are initially set in accordance with model suffix (such as EB, EG, GK, GC, and so on.).Unless the initial setting is not released, an automatic alignment software in the camera is not able to be executed when the align-ment is carried out.Note:

The initial setting should be again done after completing the alignment. Otherwise, the camera may not work properly.Therefore as a warning, the camera display a warning symbol “ ! ” on the LCD monitor every time the camera is turned off.Refer to the procedure described in “3.4.2. INITIAL SETTINGS” for details.

[ How to Release the camera initial setting ]Preparation:

• Attach the Battery or AC Adaptor with a DC coupler to the unit.(Since this unit has built-in memory, it can be performed without inserting SD memory card.)

• Remove the lens cap.

Step 1. Temporary cancellation of “INITIAL SETTINGS”:Set the mode dial to “[ P ] (Program AE mode)”.While pressing “[ UP ] of Cursor button” and [ MOTION PICTURE ] button simultaneously, turn the Power on.Step 2. Cancellation of “INITIAL SETTINGS”:Press the [ PLAYBACK ] button, then playback the picture.Press “[ UP ] of Cursor button” and [ MOTION PICTURE ] button simultaneously. (The camera will beep after this.)Turn the Power off. (The warning symbol “ ! ” is displayed on the LCD monitor.)

44

9.2.2. Flash-Rom Data BackupWhen trouble occurs, it is recommended to backup the Flash-rom data before disassembling the unit.[ ROM_BACKUP (Method of Non-PC backup) ]

1. Insert the SD memory card into the camera.2. Set the camera to “Temporary cancellation of the initial settings”. 3. Select the “SETUP” menu.

From the “SETUP” menu, select “ROM BACKUP”.NOTE:

This item is not listed on the customer’s “SETUP” menu.4. When this “ROM_BACKUP” item is selected, the following submenus are displayed.

9.2.3. Light BoxIf using VFK1164TDVLB Light Box, remove the lens connectionring by loosing three hexagon screws.

45

9.3. Details of Electrical Adjustment9.3.1. How to execute the Electrical AdjustmentIt is not necessary to connect the camera to a PC to perform adjustments.“Flag reset operation” and “Initial setting operation” are required when carrying out the alignment, follow the procedure below.

9.3.1.1. Startup Electrical Adjustment mode1. Release the initial settings.2. Insert a recordable SD memory card (32MB or more).

(Without a SD memory card, the automatic adjustmentcan not executed.)

3. Procedure to set the camera into adjustment mode:a. Set the mode dial to “[ P ] (Program AE mode)”.b. Turn the Power off.c. Turn the Power on pressing [ MENU/SET ] and

[ MOTION PICTURE ] simultaneously.LCD monitor displays “SERVICE MODE”.(Refer toFig. 3-1)

9.3.1.2. Status Adjustment Flag SettingReset (Not yet adjusted) the status flag condition.

1. After pressing the [ DISPLAY ] button, the LCD monitordisplays the Flag status screen (Refer to Fig.3-2)

2. Select item by pressing the Cursor buttons. (Gray cursoris moved accordingly.)

3. Press the [ Delete ] button.NOTE:

The selected item's flag has been changed from “F (green)” to “0 (yellow)”.

*Flag conditions:F (green)means that the alignment has been completed and thestatus flag condition is set. In this case, the flag conditionshould be reset, if you try to carry out the automatic align-ment.0 (yellow)means that the alignment has been not “completed” andthe status flag condition is “reset”. In this case, automaticalignment is available.

• In case of setting the status flag into set condition again without completion of the alignment, the status flag should be UNDO byusing ROM BACKUP function.

46

9.3.1.3. Execute Adjustment(In case of “OIS Adjustment”)

1. Perform step “9.3.1.1.” to “9.3.1.2.”, to reset the OIS flagstatus “F” (Set) to “0” (Reset)

2. Press [ DISPLAY ] button after Flag reset.OIS Adjustment screen is displayed on the LCD panel.(Refer to Fig.3-3)

3. Press the [ Shutter ] button. The adjustment will startautomatically.

4. When the adjustment is completed successfully, adjust-ment report menu appears with Green OK on the LCDmonitor. (Refer to Fig.3-4)

9.3.1.4. Attention point during Adjustment1. Step “9.3.1.3.” procedure shows OIS adjustment as an

example. To perform the adjustment, refer to the “9.3.2.Adjustment Specifications” table which shows key pointfor each adjustment.

2. Do not move the light box, the camera or the chart whileadjusting. If one of these is moved accidentally, start theadjustment again.

3. Do not press any buttons/keys until the default menu(Fig.3-5) is displayed on the LCD monitor. Otherwise,adjustment data may not be stored properly.

4. If the adjustment is interrupted accidentally, the alignmentdata may not be properly saved in the Flash-rom.

9.3.1.5. Finalizing the Adjustment1. Several adjustment flags can be reset (“F” into “0”) at the same time. In this case, when the adjustment has been completed,

the screen will change showing the adjustment for the next item until all reset items are completed. Also, when the shutter button is pressed, the screen jump to the next adjustment item.

2. To cancel the adjustment mode while in the process of performing the adjustment, follow this procedures.(1) Press [ Delete ] button.(2) Press [ RIGHT ] of Cursor button.NOTE:

• If adjustment is cancelled with above procedure, adjustment is not completed. Make sure to adjust it later.

47

9.3.2. Adjustment SpecificationsThe following matrix table shows the relation between the replaced part and the Necessary Adjustment.When a part is replaced, make sure to perform the necessary adjustment(s) in the order indicated.The table below shows all the information necessary to perform each adjustment.

48

9.4. After Adjustment9.4.1. Initial SettingSince the initial setting has been released to execute the built-in adjustment software, it should be set up again before shipping thecamera to the customer.Refer to the procedure described in “3.4.2. INITIAL SETTINGS” for details.

[ IMPORTANT ] 1. The initial setting should be done again after completing the alignment. Otherwise, the camera will not work properly.

Therefore as a warning, the camera display a warning symbol “ ! ” on the LCD monitor every time the camera is turned off.2. Confirm that status of all adjustment flag show “F”. Even if one of the adjustment flag shows “0”, initial setting programmed is

never executed.

50

10 Maintenance10.1. Cleaning Lens, Viewfinder and LCD PanelDo not touch the surface of lens, Viewfinder and LCD Panel with your hand.When cleaning the lens, use air-Blower to blow off the dust.When cleaning the LCD Panel, dampen the lens cleaning paper with lens cleaner, and the gently wipe the its surface.Note:

The Lens Cleaning KIT ; VFK1900BK (Only supplied as 10 set/Box) is available as Service Aid.

51

DMC-FZ200 OVERALL BLOCK DIAGRAM

SDCARD

(POWER SUPPLY)BATTERY

IC6001VENUS ENGINE

CAMERA PROCESSJ-PEG COMP/EXPANDSMEDIA I/FUSB I/FMAIN MICROPROCESSOR

IC1001POWER

OIS CONTROLLENS DRIVELCD DRIVESDRAM/2G-bitHDMI DRIVE

AV OUT / DIGITALTERMINAL

IC9101SYSTEM ICMICROPHONE AMPSPEAKER CONTROL

SPEAKERVIDEO OUT

IC1021,1041,1043IC1044,1045,1061IC6401REGULATORIC1042DC/DC CONVERTER

HDMITERMINAL

COLOR LCDPANEL

COLOR EVF

3.0" PANEL461k dots

0.2" PANELEQUIVALENT TO1312k dots

MIC/REMOTETERMINAL

STEREOMICROPHONE

IC5001BUS SWITCH

ECM(L)

ECM(R)

11 Block Diagram11.1. Overall Block Diagram

OVERALL BLOCK DIAGRAM

MOS IMAGE SENSOR12MAFE

FOCUSIRIS

REAR OPERATION UNIT

OIS UNIT

IC9101SYSTEM IC

MOTOR DRIVE,OIS DRIVE &PREPROCESS

FLASH

SIDE SW UNIT / TOP OPERATION UNIT

SHUTTER

IC9101SYSTEM IC

ZOOM

IC7101GYRO SENSOR

IC6004AND GATE IC

AND GATE IC

IC8001IGBT DRIVER

(25mm ~ 600mm/4:3)

X6081(72MHz)

X9101(32.27KHz)

NAND FLASH ROM/1GbitIC6005

EXT. FLASH(OPTION)

Q8101,8102QR8101,8102,8103

Q8001

HOT SHOEUNIT

52

DMC-FZ200 SYSTEM CONTROL BLOCK DIAGRAM

IC9101(SYSTEM IC)

SCCS

SO

SCSI

8784

RESETOUT

SCSCLK

)

(POWER ON L) (POWER ON L)

(POWER LED K)

(POWER LED A)

(CMD DIAL F1)

(CMD DIAL F0)

(CMD SET)

(CMD DIAL F1)

(CMD DIAL F0)

(KURUPON)

(SHUTTER 0)

(SHUTTER 1)

(MOV FN1 BUR)

(SHUTTER 0)83

SYSCK

OSCIN

OSCOUT

28

26

PW D3V

)

(FOCUS ON)

(AF)

(MF)

(FOCUS ON)

(AF)

(MF)

(S TELE WIDE) (S TELE WIDE)

(A3.1V)

(ZOOM AD)

RL9101

RL9109

RL9104

RL9103

RL9102

POWERONH

SHUTTERHALF

POWERSWONL

SHUTTER0

CL9007

TOP OPERATION UNIT

CL6014

CL6005

FP900214

FP90021

FP90022

FP90023,8,13

FP90029

FP90026

FP90027

TELE

ON OFF

CL9005

CL9032

CL9024

CL9023

CL9022

CL9016

CL9010

CL9006

CL9004

CL9003

CL9021

CL9019

CL9020

CL9002

CL9009

PW AF3.4V

C2 C1

FP90025

WIDE

SIDE SW UNIT

FLASH P.C.B.

PS9001 PP80016

PS9001 PP80017

POWER SW

67

74

71

85

70

4

11LEDOUT1(AF LED K) (AF LED K)

8LEDOUT2D8011

AF ASSIST LED

MODE DIALFP900210

FP90024,11

FP900212

PW A3.1V

MOTION PICTURE

BURST MODE

Fn1

SHUTTER(FULL)

SHUTTER(HALF)

POWER LED

57

RL9111

POWERSWONH54

X9101(32.27KHz)

QR6002

(KEY IN2)

(KEY IN3)

FP93014

FP93013

FP900621

FP900620

FP900619

FP93012

FP93023

FP93022

FP93021

FP93015

FP900622

FP93024

FP93016

FP900623

FP93025PW A3.1V

2

5

6

4

3

FOCUS

WIDE TELE

ZOOM

3 pos

AF

MF

AF/

FS9001 PP800116

FP9001 PP800117

FP9001 PP800118

FP80011

FP80013

FP80014

FP80012

REAR DIAL UNIT

SUB P.C.B.

11.2. System Control Block Diagram

SYSTEM CONTROL BLOCK DIAGRAM

IC6001(VENUS ENGINE)

(POWER ON H)

(POWER SW ON

(CMD DIAL F1)

(CMD DIAL F0)

(PON ON L)

(MOV FN1 BUR)

(SHUT HALF)

(SHUTTER 1)

(CLK27 SYS)

(SYS RESET)

(S SYSCON CS)

(S SYSCON SI)

(S SYSCON SO)

(S SYSCON SCK

(FOCUS)

(AF)

(MF)

(S TELE WIDE)

(ZOOM AD)D10

AB14

AD18

AC18

AD23

AC12

AE15

AC16

AF15

AD16

(LCD OPEN L)

GPIO49

GPIO19

GPIO20

GPIO0

GPIO30

GPIO28

GPIO29

GPIO27

RSTB

B9

GPIO72

GPIO73

GPIO71

Y4

AA1

Y3

SW7301

SW7401

(LCD ROTATE2)

(LCD ROTATE1)

D9AD0 IN9

AD0 IN8

AD0 IN7

AD0 IN11

A9

HINGE FPC

FP90032

LCD SW

HINGE SW FPC

HINGE SW

SW7302LCD OPEN SW

FP900343

FP900344

FP73012

FP73013

AB21GPIO42

AE11GPIO55

(KEY IN2)

(KEY IN3)

B14AD1 IN1

AB2GPIO67

AA4GPIO68

C9AD0 IN10

GPIO46

GPIO18

GPIO37

AB17

AF13

AE18

GPIO69AA3

S9402

(EVF LCD)FP900632

EVF/LCD SW

FP900711

FP900710

FP90078

REAR OPERATION UNIT

(CROSS KEYIN)

(REAR KEYIN2)B10 AD0 IN5

AD0 IN6

AD0 IN4

C10

AF/AE LOCK / Fn2

RIGHT

UP

LEFT

DOWN

MENU/SET

DISP.

FP90077

(REAR KEYIN1)A10

FP90071,12

FP90076

FP90075

FP90074

FP90073

(CN AF AE LOCK)

FP90079

(CN PLAY)

(DISPLAY)

(UP)

(CN FN3)

(CN MENU SET)

(CN DOWN)

(CN LEFT)

(DELETE)

(CN RIGHT)

FP90072

PLAY

FN3

Q.MENU/DEL

MULTI FPC

53

DMC-FZ200 VIDEO/AUDIO PROCESS BLOCK DIAGRAM

+-

ECM[R]+-

ECM[L]

(S SYSCON SO)(S SYSYCON SCK)

FP900336

FP9003135

FP900334

FP900315

FP900317

6FP9003

7FP9003

FP900333

18FP9003

FP900316

(LCDOUT0-15)

(LCDOUT0-15)

(S I2C SCL)

(S I2C SDA)

LCD BACK LIGHT

(CLK27 LCD)(LCD CS)

(LCD VD)(LCD HD)

(LCD CLK)

(LCD CS)

(LCD SDOUT)

(LCD SCK)

(LCDVD)

(LCDHD)

EVF

FP900427

12FP9004

3FP9004

FP900429

28FP9004

PW BL PLUS

PW BL MINUSRL9003RL9004

LCD

2

3

USB+ 5

USB- 7

8

4

6

CL5003

CL5002

CL5001

CL5007

85

89

IC9101(SYSTEM IC)

IC5001(BUS SWITCH)

LRCLK

96 2

1210

4

1

76SPPOS

79SPNEG

CABLE DET 1

(CABLE DET)

(EXT MIC ON H)

(AV KEY DET)

CL2001

CL2005

CL2007

CL2006

CL2002

CL2003

CL5201

CL5207

CL5011

CL5017 CL9057

RL5102

RL9302

RL9301

RL5101

RL5104

RL5103

CL9051

(G VIDEO OUT)

(SYS RESET)

V IN

(USB CAB IN)

51

5

6

82

CL9101

CL500692

JK2001(AV OUT/DIGITAL TERMINAL)

LINE OUT

VIDEO OUT

USB CAB IN

63

(G USB-)

(A DIN)

(A FCLK)

SDDETOUTSDDETIN

RL9112

RL5003

RL5002

43(A DOUT) RL5001

ADOUT

DAIN

4(A MCLK) RL5004

417(A DCLK) RL5005

14 MCLKO

BCLK

RESET OUT

LINEOUTLMUTEL

MICINL

99MICINR

100MREG

1A(L)

2A(R)

S

2B11B1

111B292B2

EXT MIC/REMOTE

MICPOWER

SW

Q5201,5206QR5201,5202

FP900627

FP93028

FP900628

FP93029

FP900630

FP930211

JK9301

M5001

M5002

71 SCSI70 SCSCLK

2 3

41

L2001

CL9033

FP90103

FP90101

ECM FPC

D2+ 2D2- 3D1+ 5D1- 6D0+ 8D0- 9CK+ 11CK- 12CEC 14SCL 15SDA 16

19

1 562

3 784

1 562

3 784

JK2002(HDMI TERMINAL)FL2001

FL2002

HPDTCT

(G HDMI D2+)(G HDMI D2-)(G HDMI D1+)(G HDMI D1-)(G HDMI D0+)(G HDMI D0-)(G HDMI CK+)(G HDMI CK-)(HDMI CEC)(S HDMI SCL)(S HDMI SDA)(HDMI HPDTCT)

(G USB+)

61V OUT(G SDTV OUT)(G LINE OUT)

(G EX MIC L)

(G EX MIC LIN)(G EX MIC RIN)

(G MIC LIN)(G MIC RIN)

(G EX MIC R)

(REMOTE)

PW HDMI5.0V

LCD IF P.C.B.

DR0-7/DG0-7

VSYNC

HSYNC

DCLK

SCEN

SDA

SCL

RL9102RL9103

(CLOCK)

(VSYNC)

(HSYNC)

30FP9004

FP900431

FP90047-9

(SCL)

(SDA)

(VCC LED)

(DATA0-15)

SUB P.C.B.

(G SP POS)

(G SP NEG)

SPEAKER

6FP9302

7FP9302

24FP9006

25,26FP9006

QR6001

(EVF 3V CTL)

QR9003

1 2

6 45

3

PW AF3.4V

11.3. Video/Audio Process Block Diagram

VIDEO/AUDIO PROCESS BLOCK DIAGRAM

789125

10

12

D0D1D2D3

CMDCLK

WP

6

(SDCD)C.DET


GPIO29GPIO27

IS SAB0 P

IS SAB0 M

IS SAB1 P

IS SAB1 M

IS SAB2 P

IS SAB2 M

IS SAB3 P

IS SAB3 M

IS SAB4 P

IS SAB4 M

IS SAB5 P

IS SAB5 M

IS SBCD6 P

IS SBCD6 M

IS SBCD7 P

IS SBCD7 M

IS SB8CCK P

IS SB8CCK M

IS SBCD9 P

IS SBCD9 M

IS0 HD

IS0 VD

IS0 SDO

IS0 SCK

(S MOS CS)

(MOS HD)

(MOS VD)

(BUS288 D0AP)

(BUS288 D0AM)

(BUS288 D0BP)

(BUS288 D0BM)

(BUS288 D0CP)

(BUS288 D0CM)

(BUS288 D0DP)

(BUS288 D0DM)

(BUS288 D0EP)

(BUS288 D0EM)

(BUS288 D01P)

(BUS288 D01M)

(BUS288 D0HP)

(BUS288 D0HM)

(BUS288 D0JP)

(BUS288 D0JM)

(BUS288 D0GP)

(BUS288 D0GM)

(BUS288 D0FP)

(BUS288 D0FM)

(S MOS SDO)

(S MOS SCK)

IS0 CS

LCDOUT0

LCDOUT15

AF15AD16

GPIO45

GPIO47

AB18

AB16

D15

M26

M24

M23

N23

P26

P25

P24

P23

R24

R23

J24

J25

K24

T26

T25

T24

T23

U26

U25

U24

U23

K25

J26

N24

M25

A19

GPIO48 AB15

MOSIMAGE

SENSOR12M

CL9031

CL9030

IS RESET(MOS RESET)

L24

AD2 IN3

AD2 IN2C12

AA26

AB24AB23AB26

D12

AB25AA25

SDRAM AREA/2G-bit

FP900138

FP900139

FP900136

FP900137

FP900130

FP900131

FP900118

FP900119

FP900120

FP900121

FP900122

FP900123

FP900124

FP900125

FP900126

FP900127

IS SBCK P

IS SBCK M

(BUS288 DCKP)

(BUS288 DCKM)R26

R25

FP900128

FP900129

(MOS THERMO)AD0 IN2C11FP9001

51

FP900145

FP900146

FP900143

FP900144

FP900142

FP900150

FP900134

FP900135

FP900132

FP900133

MOSSSG

RL9002

LCDCLK A20

C20B20

LCDVDLCDHD

11(SDWP)

(SDCD SYS)

VIDEO OUT

RSTB

GPIO43

GPIO50

GPIO24

AUD DIN

AUD DOUT

AUD FCLK

A8

AB13

AD0 IN3 D11

USBSIGDM

AE8

AC12

AE10

AUD MCLK

AUD DCLK

AE9

AF9

AF8

E1

(Built in AFE)

(SDDAT0)(SDDAT1)(SDDAT2)(SDDAT3)(SDCMD)(SDCLK)

GP

IO88

GP

IO89

FR R

B

CP

UR

EB

FRO

M C

S

FR C

LE

FR A

LE

CP

UW

E2B

FR W

P

F26 F25

GP

IO90

GP

IO91

E26 E25

GP

IO84

GP

IO85

H25 H24

GP

IO86

GP

IO87

G26 G25 D26 E24J23 H23 D25 F24G24

DATA

44413229

IC6005(NAND FLASH ROM/1G-bit)

7 8 9 16 17 18 19

CTL SIG

HDMI TXCM

HDMI SDAHDMI HPD

HDMI SCLHDMI CEC AD8

AE7AF7AD9

K1

HDMI TX0P

HDMI TX2PHDMI TX2MHDMI TX1PHDMI TX1M

N1M1L1

HDMI TX0MHDMI TXCP

P1

T1U1

R1

AB20

USBSIGDP D1

SD DAT0SD DAT1SD DAT2SD DAT3SD CMDSD CLK

AC17

MEMORY CONTROL BLOCK

YCPROCESSBLOCK

JPEGPROCESSBLOCK

VIDEOOUTPUTBLOCK

SD CORE

USB I/F

PREPROCESSBLOCK

INTERNAL BUS CONTROL

GPIO17 AF18

MCK24I

(CLK72 MCLK)

H1

FP900148

51

43

2

IC6004(AND GATE IC)

X6081(72MHz)

PW D3.0V PW D3.0V

P6401(SD CARD CONNECTOR)

54

DMC-FZ200 LENS/FLASH BLOCK DIAGRAM

2

3

1

1

2

3

LAMP+1

TRG IN2

UNREG GND1

LAMP-2

Q8001

D8002

C8006

P8003

P8004

P8004

P8003

(STB CHG OUT)

(EXT STB ON L)

(INT STB ON L)

(EXT STB OUT)

(EXT STB IN)

(EXT STB DET)

(OIS GY CS)

(OIS GY SCK)

(OIS GY DI)

(OIS GY DO)

(STB OPEN)

(STB OPEN)

(EXT STRTTL)

1

6

3

4

T8001CL8003CL8001

CL8009

CL8004

CL8008

CL8005

CL8010

CL8020

CL8101

CL8102

F8001

CL8006

FLASH P.C.B.

PS900111-14

PP800111-14

PP800110

PS900110

PS90018

PP80018

PS90019

PP80019

UNREG

PS90017

PP80017

CL9405

CL9402

CL9403

CL9404

AGC

D8103QR8103

Q8101

Q8102

6

5

4 3

1

2

PW D3.0V

QR8101

6

5

4 3

1

2

PW D3.0V

QR8102

QR9002

6

5

4 3

1

2

CL9027

CL9028CL9029

CL9401

CL9026

C8003(For FlashCharge)

CL8024

CL8025

D8001

IC8001(IGBT DRIVER)

RPGND

IGBT OUT

GND

VC

VCC

10

8

7

6

SW

FULL

RADJ

IGBT IN

START

1

2

3

4

5

9(STB CHG DET)

(FLASH TRG)(V7 STB TRG)

PW AF3.4V

IC7101(GYRO SENSOR)

VCCVDD

GND1

V1

9

10

11

CSB

SCLK

MISO

MOSI

172

GND2 4GND3 6

OUTMODE 13

3

8

PW A3.1VPW D3.0V

VREGA

VREGD

14

16

COSR 5

8

1

765

23

4

FP90061-6

FP900613

FP900612

FP900611

FP900614

FP900615-18

STX(STX)

(STTXD)

(STRXD)

(STRTTL)

TXD

RXD

TTL

MULTI FPC

HOT SHOE

POP UP S9401

11.4. Lens/Flash Block Diagram

LENS/FLASH BLOCK DIAGRAM

YPWM

FILTERMOS

MFOCUS MOTOR

M

IRIS MOTOR

MZOOM MOTOR

16

22

24

GPIO5

GPIO4

GPIO3

41

40

37

52

16

13

IC9101(SYSTEM IC)

8

9

10

17

FP90056

13

5

12

2

20

19

1

M

SHUTTER MOTOR

G ZENC1 MRIN

G ZENC2 MRIN

(G ZENC1 MROUT)

(G ZENC2 MROUT)GPIO57

GPIO58


120 GPIO14ED1

75

72

69

66

21

18

56

58

MN

MP

GPIO6

GPIO9

GPIO8

HALLSENSOR

HALLSENSOR

OIS UNIT

LENS UNIT

DMP

DMN

YMP

YMN

XMP

XMN

FP9005

GPIO59

FZHP LEDCNTCO. BARREL & FOCUS ENC

ZENC LEDCNT

7

39

40

37

38

FP9005

FP9005

FP9005

FP9005

22

19

BMP

BMN

43 CMP1

50

1

111

112

102

GPIO11

FP9005G XDR-

G XDR+

G XHO+

G XHO-

G YDR-

G YDR+

G YHO+

G YHO-

PWMOUT

AMP

AMN

XHN

XINP

105

104

YHNYINP

35

36

32

34

33

31

25

26

29

27

28

30

G XV+

G XV-

G YV+G YV-

XVP110

YVP107

GPIO10

47XPWM

48

REFI

GPIO2

15

14

CL7001

46 CMN121

23

101REFO

GPIO41

GPIO40

GPIO39

GPIO35

GPIO33

GPIO32

GPIO34

AD14

AF11

86

81 GPIO21PWMIN

GPIO54

C13AD1 IN6

(PWM FA)

(PWM FB)

(PWM IRIS A)

(SHUTTER A)

(S DAC CK)

(S DAC DI)

(S DAC LD)

(PWM XOIS)

(PWM YOIS)

(STB PWM)

RL7003

RL7004

RL7001G FMBP

G FMBN

G FMAP

G FMAN

SHUTP

SHUTN

G IRISAN

42 CMN2G IRISBN

G IRISAP

38 CMP2G IRISBP

G DCM+

G DCM-

RL9107

RL9106

RL9105

G FHP

G ZHP

(G FHP)(G ZHP)

AE22

Y26

Y25

AC21

AF20

Y24

ZOOM ENC

LZCK

LZDI

LZLD

EC1

EB

EA

RL7005

(STB CHG OUT)

12 PIOUT2

9 PIOUT1

118 MRIN1

119 MRIN2

MROUT1

MROUT2

44ED2

RL7006

AE21

GPIO72(PWM IRIS B)

RL7002

EC2 AD21

AE19

AD19

AF21

AC22

AD22

AD20

AE20

GPIO15(SHUTTER B)

AF17

AF12

AD13

AC13

GPIO66 AB3

GPIO65 AB4

RL9108

117

114

AF16

AE16

GPIO25

GPIO26

AF14

AC15

AE14

55

DMC-FZ200 POWER BLOCK DIAGRAM

PW D1.2V

VREGD

27VREGDVREGD2

62Hx1

Hx1

P7

CH1STEP DOWN DC/DC

(Current mode)64

Lx1

60PGND1

57Hx2

CH2STEP DOWN DC/DC

(Current mode)58

Lx2

59 PGND1

63Lx1

54Hx3

CH3STEP DOWN DC/DC

(Current mode)55

Lx3

53 PGND3

49Hx4

50Hx4

CH4STEP DOWN DC/DC

(Current mode)51

Lx4

52 PGND3

CH5STEP DOWN DC/DC

(Current mode)

CH6STEP DOWN DC/DC

(Current mode)DRIVER

PROTECTION

21RT

OSC

UVLO

LDO

OVPCOMP

SHUTDOWN

VREGA

C

CPDRIVER

P SW

1 VCC

23 CPLUS

CP SW 24 CMINUS

VREGD

VREGD2

29VREGA

20GND

44 Hx5

47Lx5

Lx5

43PGND5

38 Hx6

39 Hx6HVREGDRIVER

VREGDDRIVER

HVREGDRIVER

VREGDDRIVER

HVREGDRIVER

VREGDDRIVER

HVREGDRIVER

VREGDDRIVER

HVREGDRIVER

VREGDDRIVER

HVREGDRIVER

40Lx6

42 PGND5

46

41 Lx6

VREGD

VREGD

CH7STEP UP DC/DC(Current mode)

DRIVER 34 PGND7

33VO7

35Lx7

61

25HVREG

2

56PGND2

48PGND4

26

VBAT

3VBAT

45 Hx5

PW D3.0V

PW DM1.2V

PW AF3.4V

PW SE2.8V

PW HDMI5.0V

IC1021(REGULATOR)

2

4 1VOUT

VSS

VIN

CE

CL1010PW 5.2V

CL1050

CL1020

CL1030

CL1040

CL1021

PW A3.1V

IC1041(REGULATOR)

32

1 4VDD

VOUT

CNT

GND

CL1041

CL1080

37PGND6

36 PGND6

30VINREG

VINREG

REGOUT

VDD

VREGD2IN

31

22

28

10

PW SE1.2V

IC1061(REGULATOR)

32

1 4VIN

VOUT

CE

VSS

CL1060

3

PW EVF1.8V

IC1043(REGULATOR)

2

4 1VOUT

VSS

VIN

CE

CL1042

3

PW SE1.8V

IC1044(REGULATOR)

2

4 1VOUT

VSS

VIN

CE

CL1043

3

IC1042(DC/DC CONVERTER)

1

5

4

PHASECONPENSATION

PWM/PFMSELECTOR

CURR. F.B.CURR. LIMIT

VSHORT

LX

CE/

VSS

LOGIC

UVLO

SYNC.BUFFERDRIVE

ERRORAMP PWM

COMP.

UVLOCOMP.

VREF WITHSOFT START,

CE

RAMP WAVEGENERATOR

OSC

CE/MODECONTROL

LOGIC

VOUT

CE/MODE

6VIN

2VSS

+

3

PW D1.8V

IC1045(REGULATOR)

32

1 4VDD

VOUT

CE

VSS

CL1044

11.5. Power Block Diagram

GPIO45(S I2C SCL)

AB18

GPIO47(S I2C SDA)

AB16

POWER BLOCK DIAGRAM

P8001

BAT+ 1F8002

BAT THERMO 2

NC 3

BAT- 4 1,2,19,20

5

11-14PP8001 PS9001

PP8001

PP8501

PS9001

PS9001

FLASH P.C.B.

(UNREG)

(BAT THERMO)TOBATTERYCATCHER

ERROR AMP1SERIAL I/F

ERROR AMP2

ERROR AMP3

ERROR AMP4

ERROR AMP5

ERROR AMP6

ERROR AM

SCP6TIMER

SCPTIMER

SS TIMER

12SEQ

0.3V

SERIALI/F

ON/OFFLOGIC

IC1001(7CH SW REGULATOR)

PW BL PLUS(To FP9003-6)

CL9011

CL9012

SERIAL I/F

Vo3SEL

SERIAL I/F

SERIAL I/F

SERIAL I/F

SERIAL I/F

SERIAL I/F

SCPLDOTIMER

16

CTL SEQ3

CTL SEQ2

CTL SEQ1

CTL123417

18SCL

19SDA

14

13

32INV7

VO69

VO58

VO47

VO36

VO25

4VO1

Q1071

PW BL MINUS(To FP9003-7)

VDD(To P6401-4A,4B)

CL1071

CL1072

CL1070

GPIO20

RSTB

AD0 IN1

(POWER SW ON)

(POWER ON H)

(POWER ON L)

(SYS RESET)

ON

OFF

POWER SW

FP900214

TOP OPERATION UNIT

IC9101

CL9004

CL9008


54

87

(SYSTEM IC)

35

POWER SW ON L

POWER SW ON H

POWER CTL SW

POWER ON H

GPIO42

84 85

34UNREG

RL9111

CL6014

CL9102

CL1001

Q9101

AB21

AC18

AC12

B11

AD0 IN0 A11

GPIO31 AD15

RESETOUT

(LCD BLT)

(BATT THERMO)

(SW UNREG)

27 BATT(BACKUP)

36FP9006

14FP9302

SUB P.C.B.

BACK BATTB9301

AF10(SD POWER ON )

(1R8V ON)

(3R0V ON)

(PW SD3018V)

GPIO76

IC6401(REGULATOR)

VOUT VIN

VCNT2 3

41

VSS

GPIO56

CL6401

CL6402

123

4 65

Q6401

QR6401

QR6402VDD SDVDD SD

W4

GPIO77 W3

AA22Y20

56

DMC-FZ200 INTERCONNECTION DIAGRAM

(STEREO MICROPHONE)ECM(L) ECM(R)

ECM FPC

REAR OPERATION UNIT

TOPOPERATION

UNIT

EVF

N P.C.B.L SIDE)

: (COMPONENT SIDE)7 6 5 4 3 2 1

ZOO

M A

DS

HU

TTE

R 1

MO

V F

N1

BU

RP

W A

3R1V

D G

ND

PO

WE

R L

ED

AP

OW

ER

LE

D K

FP90

071 2 3 4 5 6 7 8 9 10 11 12

GN

DD

ELE

TELE

FTD

OW

NS

ET

RIG

HT

UP

FN3

PLA

YA

E A

F LO

CK

DIS

PLA

YG

ND

FLASH P.C.B.(COMPONENT SIDE)

: (FOIL SIDE)

BATTERY

REAR DIAL UNIT

PP800110987654321

11121314151617181920

UNREGUNREGUNREGUNREG

NCCMD DIAL F1

CMD SETCMD DIAL FOUNREG GNDUNREG GND

STB CHG OUTFLASH TRG

STB CHG DETPW 3.4VAF LED K

BAT THERMOD GNDD GND

UNREG GNDUNREG GND

P8003

LAMP-

LAMP+

1 2

P8004

TRG

IN

UN

REG

GN

D1 2

FP80

01C

MD

DIA

L F0

CM

D S

ET

D G

ND

CM

D D

IAL

F1

4 3 2 1

FLASHUNIT

P8001BAT-NC

BAT THERMOBAT+

4321

LCD IF P.C.B.(FOIL SIDE)

GN

DD

2R5V

D3V

LCD

VD

LCD

CLK

LCD

OU

T14

LCD

OU

T12

LCD

OU

T10

LCD

OU

T8LC

DO

UT6

LCD

OU

T4LC

DO

UT2

LCD

OU

T0LC

D S

CK

GN

DG

ND

GN

DG

ND

BL+

GN

D

GN

DD

3VD

3VLC

DH

DLC

DO

UT1

5LC

DO

UT1

3LC

DO

UT1

1LC

DO

UT9

LCD

OU

T7LC

DO

UT5

LCD

OU

T3LC

DO

UT1

LCD

SD

OU

TLC

D C

SG

ND

GN

DG

ND

BL -

GN

D

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38

1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39

VGLC4PC3P

SCENSDADR6DR4DR2DR0DG6DG4DG2DG0

HSYNCVDDLVSS1

VCOMLVCMCXP

VCIX2C2NC1NVS

C4NC3NVGHSCLDR7DR5DR3DR1DG7DG5DG3DG1

DCLKVSYNCVDDIO1

VGMVCOMH

CXNVCI

VSS2C2PC1P

2468

101214161820222426283032343638404244

13579

111315171921232527293133353739414345

LCD

HINGE SW FPCHINGE FPC

LCD UNIT

12 Wiring Connection Diagram12.1. Interconnection Diagram

INTERCONNECTION DIAGRAM

HOT SHOE UNIT

SIDE SW UNIT

MULTI FPC

SUB P.C.B.(COMPONENT SIDE)

FP9301654321

A3.1VS TELE-WIDE

MFAF

FOCUS OND GND

FP93

0214 13 12 11 10 9 8 7 6 5 4 3 2 1

BA

CK

UP

NC

D G

ND

RE

MO

TEM

IC G

ND

MIC

RM

IC L

SP

-S

P+

A3.

1VS

TE

LE W

OD

EM

FA

FFO

CU

S O

N

SPEAKER

RL9301 RL9302

MAI(FOI

FP90

0214 13 12 11 10 9 8

PO

WE

R O

N L

D G

ND

KE

Y IN

2P

W A

3R1V

KE

Y IN

3S

HU

TTE

R 0

D G

ND

FP90

104 3 2 1

MIC

GN

DM

IC L

INM

IC G

ND

MIC

R IN

FP9001GND

AVDD28GNDGND

DVDD12GND

DVDD18GNDGNDDOIMDOHMDOJMDOGMDOFMDCKMDOEMDODMDOCMDOBMDOAMGNDCSHD

GNDGND

SENSOR THERMO

GNDAVDD28

GNDDVDD12

GNDGND

DVDD18GNDDOIPDOHPDOJPDOGPDOFPDCKPDOEPDODPDOCPDOBPDOAPGNDSCK

SDATAVD

MCLKRSTN

2468

101214161820222426283032343638404244464850

13579

111315171921232527293133353739414345474951

FP9004GND

CLOCKVCC

VCC LEDVCC LED

VCCXDATA1DATA3DATA5DATA7DATA9

DATA11DATA13DATA15HSYNC

SDAGND

GNDNRESET

VCCVCC LED

VCCIODATA0DATA2DATA4DATA6DATA8

DATA10DATA12DATA14VSYNC

SCLGND

2468

101214161820222426283032

13579

111315171921232527293133

FP9006

STX

STX

STX NC

NC

STR

TTL

STT

XD

FRA

ME

GN

DFR

AM

E G

ND

FOC

US

ON

MF

A3.

1VS

P-

MIC

LM

IC G

ND

D G

ND

NC

NC

NC

STX

STX

STX NC

NC

STR

XD

STB

OP

EN

FRA

ME

GN

DFR

AM

E G

ND

AF

S T

ELE

-WID

ES

P+

SP

-M

IC R

RE

MO

TEE

VF

LCD

NC

BA

CK

UP

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36

1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37

FP9005123456789

10111213141516171819202122232425262728293031323334353637383940

ABS (ZHP)LED CONT (ZHP LED)ZHP VCC(D2R9V)ENC VCC (D2R9V)

ABS (ZENC1)LED CONT (Z1 LED)

ZM1 (DCM+)ZM1 (DCM+)ZM2 (DCM-)ZM2 (DCM-)

ENC VCC (D2R9V)ABS (ZENC2)

LED CONT (Z2 LED)FAN (FMAN)FBP (FMBP)FAP (FMAP)FBN (FMBN)

FHP VCC (D2R9V)ABS (FHP)

LED CONT (FHP LED)ST2 (IRIS AN)ST1 (IRIS AP)ST4 (IRIS BN)ST3 (IRIS BP)

Y DRV- (Y DR-)Y DRV+ (Y DR+)

Y HI- (YVH-)Y HO+ (YVO+)Y HI+ (YVH+)Y HO- (YVO-)X HI- (XVH-)

X HO+ (XVO+)X HI+ (XVH+)X HO- (XVO-)

X DRV- (X DR-)X DRV+ (X DR+)

SH- (SHUT OUT1)SH- (SHUT OUT1)SH+ (SHUT OUT2)SH+ (SHUT OUT2)

D G

ND

D G

ND

CM

D D

IAL

F0K

UR

UP

ON

CM

D D

IAL

F1N

CU

NR

EG

UN

RE

GU

NR

EG

UN

RE

G

D G

ND

D G

ND

D G

ND

D G

ND

BA

T TH

ER

MO

AF

LED

KP

W 3

.4V

STB

CH

G D

ET

FLA

SH

TR

GS

TB C

HG

OU

T

1 2 3 4 5 6 7 8 9 10

20 19 18 17 16 15 14 13 12 11

PS

9001

FP9003GNDGNDGNDBL-

GNDGNDGND

LCD CSLCD SDOUTLCDOUT1LCDOUT3LCDOUT5LCDOUT7LCDOUT9

LCDOUT11LCDOUT13LCDOUT15

LCDHDD3VD3VGND

LCD ROTATE2GND

LCD ROTATE1GNDBL+GNDGNDGNDGND

LCD SCKLCDOUT0LCDOUT2LCDOUT4LCDOUT6LCDOUT8

LCDOUT10LCDOUT12LCDOUT14LCD CLKLCDVD

D3VD1R8VGND

LCD OPEN L

2468

101214161820222426283032343638404244

13579

111315171921232527293133353739414345

LENSUNIT MOS IMAGE SENSOR

(MOS/AFE)

MOS FPC

57

Model No. : DMC-FZ200 Schematic Diagram Note

Model No. : DMC-FZ200 Parts List Note

Model No. : DMC-FZ200 Power (P) (Main P.C.B.)

Model No. : DMC-FZ200 Jack (J) (Main P.C.B.)

Model No. : DMC-FZ200 EXT MIC (EM) (Main P.C.B.)

Model No. : DMC-FZ200 Digital (D) (Main P.C.B.)

Model No. : DMC-FZ200 SD Card (SD) (Main P.C.B.)

Model No. : DMC-FZ200 Gyro (GY) (Main P.C.B.)

Model No. : DMC-FZ200 Hot Shoe (HS) (Main P.C.B.)

Model No. : DMC-FZ200 Main Connection (MC) (Main P.C.B.)

Model No. : DMC-FZ200 System Driver (SY) (Main P.C.B.)

Model No. : DMC-FZ200 Flash (Flash P.C.B.)

Model No. : DMC-FZ200 Sub (Sub P.C.B.)

Model No. : DMC-FZ200 Lens Flex (Lens Flex P.C.B.)

Model No. : DMC-FZ200 Main P.C.B. (Component Side)

Model No. : DMC-FZ200 Main P.C.B. (Foil Side)

Model No. : DMC-FZ200 Flash P.C.B. (Component Side)

Model No. : DMC-FZ200 Flash P.C.B. (Foil Side)

Model No. : DMC-FZ200 Sub P.C.B. (Component Side)

Model No. : DMC-FZ200 Sub P.C.B. (Foil Side)

Model No. : DMC-FZ200 Lens Flex P.C.B.

Model No. : DMC-FZ200 Parts List

Change Safety Ref. No. Part No. Part Name & Description Q'ty Remarks

C1001 F1H1A4750004 C.CAPACITOR CH 10V 4.7U 1

C1002 F1G1A1040006 C.CAPACITOR CH 10V 0.1U 1


C1004 F1G0J1050007 C.CAPACITOR CH 6.3V 1U 1





C1009 ECJ1VB1A105K C.CAPACITOR CH 10V 1U 1

C1010 F1J0J2260004 C.CAPACITOR CH 6.3V 22U 1

C1011 F1J1A106A043 C.CAPACITOR CH 10V 10U 1





















C1070 F1J1V1050001 C.CAPACITOR CH 35V 1U 1











C5009 F1H0J4750004 C.CAPACITOR CH 6.3V 4.7U 1


C5011 F1G1A473A032 C.CAPACITOR CH 10V 0.047U 1



C5017 F1G1A473A032 C.CAPACITOR CH 10V 0.047U 1



C5020 F1G1H470A557 C.CAPACITOR CH 50V 47P 1


C5022 F1G1H4710004 C.CAPACITOR CH 50V 470P 1


C5201 F1G1E472A086 C.CAPACITOR CH 25V 4700P 1












C6006 F1G1C1030008 C.CAPACITOR CH 16V 0.01U 1

























































C8001 F1G0J1050007 C.CAPACITOR CH 6.3V 1U 1 [PAVCX]

C8002 F1K2J223A029 C.CAPACITOR 630V 0.022U 1 [PAVCX]

C8006 F1K2J223A029 C.CAPACITOR 630V 0.022U 1 [PAVCX]



C8007 F1G1H270A565 C.CAPACITOR CH 50V 27 1 [PAVCX]

C8009 F1J1A106A043 C.CAPACITOR CH 10V 10U 1 [PAVCX]

























CX6001 F5A84103A020 CAPACITOR NETWORKS 1



D1001 B0JCGD000016 DIODE 1 E.S.D.

D1051 B0JCMD000066 DIODE 1 E.S.D.

D1070 B0JCFC000003 DIODE 1 E.S.D.

D2001 DB2S31100L DIODE 1 E.S.D.

D8001 B0ECGP000006 DIODE 1 [PAVCX]E.S.D.

D8002 B0ECFR000003 DIODE 1 [PAVCX]E.S.D.

D8011 B3ADB0000142 DIODE 1 [PAVCX]E.S.D.

D8101 DZ2J082M0L DIODE 1 E.S.D.

D8103 B2ABAP000006 DIODE 1 E.S.D.

ET2001 K4ZZ01000208 EARTH TERMINAL 1

ET2002 K4ZZ01000208 EARTH TERMINAL 1F1071 K5H1512A0024 FUSE 50V 0.15A 1F2001 K5H1522A0018 FUSE 32V 1.5A 1F8001 K5H152YA0080 FUSE 32V 2.0A 1 [PAVCX]F8002 K5H252YA0080 FUSE 32V 2.5A 1 [PAVCX]

FL2001 EXC28CH900U FILTER 1

FL2002 EXC28CH900U FILTER 1

FP8001 K1MY04BA0370 CONNECTOR 4P 1 [PAVCX]

FP9001 K1MY51BA0235 CONNECTOR 51P 1




FP9005 K1MN40BA0153 CONNECTOR 40P 1






IC1001 C1ZBZ0004634 IC 1 E.S.D.

IC1021 C0DBGYY02517 IC 1 E.S.D.


IC1042 C0DBAYY01175 IC 1 E.S.D.







IC5001 C0JBAR000567 IC 1 E.S.D.

IC6001 VSG1014 IC 1 E.S.D.

IC6004 C0JBAA000479 IC 1 E.S.D.

IC6005 29LV8BFZ200 IC 1 E.S.D.


IC7101 EWTS9PSX1A IC 1 E.S.D.

IC8001 C0ZBZ0001817 IC 1 [PAVCX]E.S.D.

IC9101 C1AB00003449 IC 1 E.S.D.

JK2001 K1FB108E0008 JACK, AV OUT/DIGITAL 1

JK2002 K1FA119E0020 JACK, HDMI 1

JK9301 K2HD104D0002 JACK 1 [PAVCX]

L1010 G1C4R3M00003 CHIP INDUCTOR 4.3UH 1

L1020 G1C100MA0461 CHIP INDUCTOR 10UH 1



L1041 G1C4R7MA0477 CHIP INDUCTOR 4.7UH 1




L2001 J0ZZB0000142 FILTER 1

L6401 G1C1R0MA0172 CHIP INDUCTOR 1UH 1

LB2001 J0JCC0000415 FILTER 1




LB2005 J0JBC0000107 FILTER 1




LB6002 J0JYC0000046 FILTER 1

LB6004 D0YAR0000007 FILTER 1




P6401 K1NA09E00153 SD CARD CONNECTOR 1

P8001 K4ZZ04000059 CONNECTOR 4P 1 [PAVCX]

P8003 K1KA02B00292 CONNECTOR 2P 1 [PAVCX]

P8004 K1KA02BA0014 CONNECTOR 2P 1 [PAVCX]

PP8001 K1KA20BA0052 CONNECTOR 20P 1 [PAVCX]

PS9001 K1KB20AA0094 CONNECTOR 20P 1

Q1071 FK3503010L TRANSISTOR 1 E.S.D.

Q5201 B1ABDF000017 TRANSISTOR 1 E.S.D.

Q5206 B1ABDF000017 TRANSISTOR 1 E.S.D.

Q6401 B1CHMB000007 TRANSISTOR 1 E.S.D.

Q8001 B1JBLP000037 TRANSISTOR 1 [PAVCX]E.S.D.

Q8101 B1CFHD000027 TRANSISTOR 1 E.S.D.

Q8102 B1ABCF000103 TRANSISTOR 1 E.S.D.

Q9101 DSC900100L TRANSISTOR 1 E.S.D.

QR5201 B1GDCFNN0031 TRANSISTOR-RESISTOR 1 E.S.D.

QR5202 B1GBCFNL0020 TRANSISTOR-RESISTOR 1 E.S.D.

QR6001 DRC3144W0L TRANSISTOR-RESISTOR 1 E.S.D.

QR6002 B1GBCFJN0041 TRANSISTOR-RESISTOR 1 E.S.D.

QR6401 B1GBCFJJ0064 TRANSISTOR-RESISTOR 1 E.S.D.

QR6402 B1GDCFGN0024 TRANSISTOR-RESISTOR 1 E.S.D.

QR8101 B1GKCFGN0003 TRANSISTOR-RESISTOR 1 E.S.D.

QR8102 B1GBCFJJ0064 TRANSISTOR-RESISTOR 1 E.S.D.

QR8103 B1GKCFJN0003 TRANSISTOR-RESISTOR 1 E.S.D.

QR9002 B1GFCFJJ0016 TRANSISTOR-RESISTOR 1 E.S.D.

QR9003 B1GKCFGG0003 TRANSISTOR-RESISTOR 1 E.S.D.



R1001 ERJ2RHD473 M.RESISTOR CH 1/16W 47K 1

R1072 ERJ2RKD120 M.RESISTOR CH 1/16W 12 1

R2001 ERJ2GEJ750 M.RESISTOR CH 1/10W 75 1


R2003 ERJ2GEJ102Y M.RESISTOR CH 1/10W 1K 1


R2011 ERJ2GEJ202 M.RESISTOR CH 1/10W 2K 1

R2012 ERJ2GED273X M.RESISTOR CH 1/10W 27K 1


R2016 ERJ2RHD682X M.RESISTOR CH 1/10W 6.8K 1



R5012 ERJ2GEJ222 M.RESISTOR CH 1/10W 2.2K 1



R5201 ERA3YED562V M.RESISTOR CH 1/16W 5.6K 1

R5202 ERA3YED331 M.RESISTOR CH 1/16W 330 1

R5203 ERA3YED562V M.RESISTOR CH 1/16W 5.6K 1





R6001 ERJ2RKF1183 M.RESISTOR CH 1/16W 118K 1

R6002 ERJ2RHD222 M.RESISTOR CH 1/16W 2.2K 1

R6004 ERJ2RHD122 M.RESISTOR CH 1/16W 1.2K 1

R6005 ERJ2RHD561 M.RESISTOR CH 1/16W 560 1






R6022 ERJ2RKF6201 M.RESISTOR CH 1/16W 6.2K 1


R6027 ERJ2RKF2800 M.RESISTOR CH 1/16W 28 1

























R7009 D1BA1R00A079 M.RESISTOR CH 1/8W 1 1

R7021 ERJ2RHD822X M.RESISTOR CH 1/16W 8.2K 1

R8002 D0GB104JA065 M.RESISTOR CH 1/10W 100K 1 [PAVCX]

R8003 D0GB680JA065 CHIP RESISTOR 1 [PAVCX]



R8005 ERJ6GEYJ514V M.RESISTOR CH 1/8W 510K 1 [PAVCX]


R8013 ERJ2RHD1621X M.RESISTOR CH 1/16W 1620 1 [PAVCX]

R8021 D0GA473JA023 CHIP RESISTOR 1 [PAVCX]

R8032 D1BD4703A119 CHIP RESISTOR 1 [PAVCX]


R8034 ERJ8GEYJ472V M.RESISTOR CH 1/4W 4.7K 1 [PAVCX]




R8107 ERJ6GEYJ106V M.RESISTOR CH 1/10W 10M 1

R8108 ERJ6GEYJ106V M.RESISTOR CH 1/10W 10M 1






































R9067 ERJ2GEJ752X M.RESISTOR CH 1/10W 7.5K 1










R9106 ERJ2RKD105 M.RESISTOR CH 1/16W 1M 1

R9107 ERJ2RKD224 M.RESISTOR CH 1/16W 220K 1




R9114 ERJ2RHD823 M.RESISTOR CH 1/16W 82K 1




R9123 D0GB180JA057 M.RESISTOR CH 1/10W 18 1

R9124 D0GB150JA057 M.RESISTOR CH 1/10W 15 1

RX6001 EXBN8V103J RESISTOR NETWORKS 1

RX6002 EXBN8V101JX RESISTOR NETWORKS 1














T8001 G5DYA0000137 TRANSFORMER 1 [PAVCX]

VA9021 D4ED18R00008 VARISTOR 1

X6081 H4Z7205B0001 CRYSTAL OSCILLATOR 1

X9101 H0J327200085 CRYSTAL OSCILLATOR 1

Model No. : DMC-FZ200 Frame and Casing Section

Model No. : DMC-FZ200 Camera Lens Section

Model No. : DMC-FZ200 Packing Parts and Accessories Section



1 VEP56170A MAIN P.C.B. 1 (RTL) E.S.D. P,PC,PU,EE,GC,SG,GT,GK,GN

1 VEP56170B MAIN P.C.B. 1 (RTL) E.S.D. EG,EP,EF,EB

1-1 VGQ1H72 MAIN COPPER SHEET 1

1-2 VGQ1H73 HEAT RADIATION SHEET 1

2 K0RB01000015 REAR OPERATION UNIT 1

3 K0RB01700001 TOP OPERATION UNIT 1

4 L5EDDYY00421 EVF UNIT 1

5 VKM9529 LCD CASE (TOP) 1

6 VKM0B72 LCD CASE (BOTTOM) 1

7 VYK5G58 LCD UNIT 1

8 VGQ1E10 JACK HOLDER 1

9 VMC2111 SHOE SPRING 1

30 VEP59105A HINGE SW FPC 1 [PAVCX]

31 VGQ0V71 HINGE SW FPC SHEET 1 [PAVCX]

32 VGQ0Y75 HINGE SW TAPE 1 [PAVCX]

33 VGQ0Y75 HINGE SW TAPE 1 [PAVCX]

34 VKM0B75 HINGE ARM COVER TOP 1 [PAVCX]

35 VKM0B76 HINGE ARM COVER BOTTOM 1 [PAVCX]

36 VMC2217 REAR EARTH PLATE B 1 [PAVCX]

37 VMP0A09 HINGE PLATE 1 [PAVCX]

38 VYK5V56 REAR CASE UNIT 1 [PAVCX]

39 VYK5W48 LCD HINGE UNIT 1 [PAVCX]

39-1 VGQ1H74 DPR SHEET 1 [PAVCX]40 F9Z000000038 E.CAPACITOR 1 [PAVCX](C8003)

41 K0RB00300004 SWITCH UNIT 1 [PAVCX]

42 VEP58183A FLASH P.C.B. 1 [PAVCX](RTL) E.S.D.

43 VGQ1D82 CONDENSOR COVER 1 [PAVCX]

44 VYK5V61 BATTERY CASE UNIT 1 [PAVCX]

45 K0RB00300003 SIDE SWITCH UNIT 1 [PAVCX]

46 L0AA01A00100 SPEAKER 1 [PAVCX]47 ML-614S/DN BUTTON BATTERY 1 [ENERGY] (B9301)

48 VDW2491 LENS RING FRONT 1 [PAVCX]

49 VEP59120A SUB P.C.B. 1 [PAVCX](RTL)

50 VGQ0W52 REMOTE HOLDER 1 [PAVCX]

51 VGQ1D75 GRIP PIECE FRONT 1 [PAVCX]

52 VGQ1D78 STRAP HOLDER (R) 1 [PAVCX]

53 VGQ1H40 SP SPACER A 1 [PAVCX]

54 VKF5073 REMOTE COVER 1 [PAVCX]

55 VMP0C97 SIDE FRAME (R) 1 [PAVCX]

56 VSC6424 FRONT HEAT SINK 1 [PAVCX]

57 VYK5V53 FRONT CASE UNIT 1 [PAVCX]

59 EFN-AMDK7ZJ FLASH 1 [PAVCX]

60 VEK0T25 HOT SHOE UNIT 1 [PAVCX]

61 VEP54034A MIC FPC UNIT 1 [PAVCX]

62 VGQ1F41 MULTI HOT SHOE FPC SHEET 1 [PAVCX]

63 VKM0B70 FLASH CASE BOTTOM 1 [PAVCX]

64 VKM0B74 FLASH LINK COVER 1 [PAVCX]

65 VMB4614 FLASH SPRING 1 [PAVCX]

66 VMM0479 FLASH LINK 1 [PAVCX]

67 VMS8267 FLASH SHAFT 1 [PAVCX]

68 VMS8286 FLASH SHAFT 2 1 [PAVCX]

69 VMT1962 MIC DAMPER 1 [PAVCX]

70 VMT2011 MIC CUSHION 1 [PAVCX]

71 VYK5V58 FLASH CASE TOP UNIT 1 [PAVCX]

72 VYK5Z73 FLASH BASE UNIT 1 [PAVCX]

73 VGQ1H36 REED WIRE SHEET 1 [PAVCX]

B1 VHD2149 SCREW 1

B2 VHD2149 SCREW 1

B3 VHD2179 SCREW 1

B4 VHD2179 SCREW 1

B5 XQN16+BJ4FN SCREW 1



B6 XTV2+8JFN SCREW 1




B10 VHD1870 SCREW 1

B11 VHD1870 SCREW 1

B12 VHD1870 SCREW 1

B13 VHD1870 SCREW 1

B14 VHD1870 SCREW 1

B15 VHD2337 SCREW 1

B16 VHD2337 SCREW 1

B17 VHD2337 SCREW 1

B18 VHD2337 SCREW 1

B19 VHD2337 SCREW 1

B20 VHD2337 SCREW 1

B30 VHD2190 SCREW 1 [PAVCX]





B36 XQN16+BJ4FN SCREW 1 [PAVCX]














100 VXW1531 LENS UNIT (W/O MOS) 1

101 VXP3823 1ST LENS FRAME UNIT 1

102 VXP3824 2ND LENS FRAME UNIT 1

103 VXQ2295 MIDDLE FRAME UNIT 1

104 L6HAYYYD0056 FOCUS MOTOR UNIT 1

105 VMC2225 CAM FRAME SPRING 1

106 VXP3825 3RD LENS FRAME UNIT 1

107 VXP3828 4TH LENS FRAME UNIT 1

108 VXP3830 5TH LENS FRAME UNIT 1

109 VDW2567 CAM FRAME 1

110 L6DAYYYC0005 ZOOM MOTOR 1

111 VXQ2296 MASTER FLANGE UNIT 1

112 VEK0T33 LENS FLEX UNIT 1

113 VMB4205 TILT SPRING 1

114 VMB4205 TILT SPRING 1

115 VEK0T48 MOS UNIT 1 E.S.D.

B101 VHD1974 SCREW 1















B114 VHD2351 SCREW 1200 ----- BATTERY 1201 DE-A79BB BATTERY CHARGER 1 P,PC201 DE-A80AC BATTERY CHARGER 1 PU,EG,EP,EF,EB,EE,GN201 DE-A80BD BATTERY CHARGER 1 GC,GK201 DE-A80DA BATTERY CHARGER 1 SG201 DE-A80CB BATTERY CHARGER 1 GT

202 K1HY08YY0025 USB CONNECTION CABLE 1

203 VFC4453 SHOULDER STRAP 1

204 VYQ5607 LENS CAP UNIT 1

205 VYQ7878 LENS HOOD UNIT 1

206 VPF1166 CAMERA BAG 1

207 VPK5409 PACKING CASE 1 EXCEPT GK

207 VPK5412 PACKING CASE 1 GK

208 VPN7421 CUSHION 1210 VFF1045 CD-ROM (INSTRUCTION BOOK) 1 P,PC,PU210 VFF1046 CD-ROM (INSTRUCTION BOOK) 1 EG,EP,EF,EB210 VFF1047 CD-ROM (INSTRUCTION BOOK) 1 EE210 VFF1048 CD-ROM (INSTRUCTION BOOK) 1 GC,SG,GN210 VFF1049 CD-ROM (INSTRUCTION BOOK) 1 GT210 VFF1050 CD-ROM (INSTRUCTION BOOK) 1 GK

211 VPF1230 BAG, POLYETHYLENE 1212 VQT4H46 BASIC O/I (ENGLISH/SPANISH) 1 P212 VQT4H47 BASIC O/I (ENGLISH/CANADIAN FRENCH) 1 PC212 VQT4H48 BASIC O/I (SPANISH/PORTUGUESE) 1 PU212 VQT4H49 BASIC O/I (GERMAN/TURKISH) 1 EG212 VQT4H50 BASIC O/I (ITALIAN/DUTCH) 1 EG212 VQT4H51 BASIC O/I (SPANISH/PORTUGUESE) 1 EG212 VQT4H52 BASIC O/I (FRENCH) 1 EG,EF212 VQT4H53 BASIC O/I (SWEDISH/DANISH) 1 EP212 VQT4H54 BASIC O/I (POLISH/CZECH) 1 EP212 VQT4H55 BASIC O/I (HUNGARIAN/FINNISH) 1 EP212 VQT4H57 BASIC O/I (ENGLISH) 1 EB212 VQT4H58 BASIC O/I (RUSSIAN/UKRAINIAN) 1 EE

212 VQT4H59 BASIC O/I (ENGLISH/CHINESE(TRADITIONAL)) 1 GC,SG

212 VQT4H60 BASIC O/I (ARABIC/PERSIAN) 1 GC212 VQT4H61 BASIC O/I (VIETNAMESE) 1 GC212 VQT4J57 BASIC O/I (CHINESE(TRADITIONAL)) 1 GT212 VQT4H62 BASIC O/I (CHINESE(SIMPLIFIED)) 1 GK212 VQT4H63 BASIC O/I (ENGLISH) 1 GN

213 VFF1023-E CD-ROM(SOFT) 1 EXCEPT GK See "Notes"

213 VFF1024-E CD-ROM(SOFT) 1 GK See "Notes"

214 VQL2C67-2 OPERATING LABEL 1 PC

214 VQL2C68-1 OPERATING LABEL 1 GT215 K2CA2CA00025 AC CORD W/PLUG 1 PU215 K2CQ2YY00082 AC CORD W/PLUG 1 EG,EP,EF,EE,GC215 K2CT3YY00034 AC CORD W/PLUG 1 EB,GC215 K2CA2YY00247 AC CORD W/PLUG 1 SG215 K2CA2YY00129 AC CORD W/PLUG 1 GT215 K2CA2YY00130 AC CORD W/PLUG 1 GK215 K2CJ2YY00052 AC CORD W/PLUG 1 GN

panasonic dmc-fz200 p pc pu eb ee ef eg ep gc gk gn gt sg

Documents

overall block diagram

lensflash block diagram

power block diagram

system control block

service fixture tools

service navigation

service mode

service position