panasonic dmc-fz100 sm
DESCRIPTION
Panasonic Dmc-fz100 Sm servicee manualTRANSCRIPT
ORDER NO. DSC1007045CEB26
Digital CameraModel No. DMC-FZ100P
DMC-FZ100PCDMC-FZ100PUDMC-FZ100EBDMC-FZ100EEDMC-FZ100EFDMC-FZ100EGDMC-FZ100EPDMC-FZ100GCDMC-FZ100GDDMC-FZ100GKDMC-FZ100GNDMC-FZ100GTDMC-FZ100SG
Vol. 1Colour(K)...........Black Type
© Panasonic Corporation 2010 Unauthorized copy-ing and distribution is a violation of law.
TABLE OF CONTENTSPAGE PAGE
1 Safety Precautions -----------------------------------------------31.1. General Guidelines ----------------------------------------31.2. Leakage Current Cold Check ---------------------------31.3. Leakage Current Hot Check (See Figure 1.)--------31.4. How to Discharge the E.Capacitor on Flash
P.C.B.----------------------------------------------------------42 Warning --------------------------------------------------------------5
2.1. Prevention of Electrostatic Discharge (ESD)to Electrostatically Sensitive (ES) Devices ----------5
2.2. How to Recycle the Lithium Ion Battery (U.S.Only)-----------------------------------------------------------5
2.3. Caution for AC Cord(For EB/GC) ----------------------62.4. How to Replace the Lithium Battery-------------------7
3 Service Navigation------------------------------------------------83.1. Introduction --------------------------------------------------83.2. Service Navigation-----------------------------------------83.3. General Description About Lead Free Solder
(PbF) ----------------------------------------------------------93.4. Important Notice 1:(Other than U.S.A. and
Canadian Market) ------------------------------------------93.5. How to Define the Model Suffix (NTSC or PAL
model)------------------------------------------------------- 104 Specifications ---------------------------------------------------- 145 Location of Controls and Components------------------ 156 Service Mode ----------------------------------------------------- 19
6.1. Error Code Memory Function ------------------------- 196.2. ICS (Indication of additional Camera Settings
when picture was taken) function -------------------- 217 Service Fixture & Tools --------------------------------------- 23
7.1. Service Fixture and Tools ------------------------------ 237.2. When Replacing the Main P.C.B. -------------------- 247.3. Service Position ------------------------------------------ 24
8 Disassembly and Assembly Instructions --------------- 258.1. Disassembly Flow Chart-------------------------------- 258.2. P.C.B. Location ------------------------------------------- 258.3. Disassembly Procedure -------------------------------- 268.4. Lens Disassembly Procedure------------------------- 368.5. Removal of the MOS SENSOR Unit ---------------- 41
9 Measurements and Adjustments -------------------------- 429.1. Introduction ------------------------------------------------ 429.2. Before Disassembling the unit ------------------------ 429.3. Details of Electrical Adjustment----------------------- 449.4. After Adjustment------------------------------------------ 48
10 Maintenance ------------------------------------------------------ 4910.1. Cleaning Lens, Viewfinder and LCD Panel -------- 49
2
1 Safety Precautions1.1. General Guidelines
1. IMPORTANT SAFETY NOTICEThere are special components used in this equipmentwhich are important for safety. These parts are marked by
in the Schematic Diagrams, Circuit Board Layout,Exploded Views and Replacement Parts List. It is essen-tial that these critical parts should be replaced with manu-facturer’s specified parts to prevent X-RADIATION,shock, fire, or other hazards. Do not modify the originaldesign without permission of manufacturer.
2. An Isolation Transformer should always be used duringthe servicing of AC Adaptor whose chassis is not isolatedfrom the AC power line. Use a transformer of adequatepower rating as this protects the technician from acci-dents resulting in personal injury from electrical shocks. Itwill also protect AC Adaptor from being damaged by acci-dental shorting that may occur during servicing.
3. When servicing, observe the original lead dress. If a shortcircuit is found, replace all parts which have been over-heated or damaged by the short circuit.
4. After servicing, see to it that all the protective devicessuch as insulation barriers, insulation papers shields areproperly installed.
5. After servicing, make the following leakage currentchecks to prevent the customer from being exposed toshock hazards.
1.2. Leakage Current Cold Check1. Unplug the AC cord and connect a jumper between the
two prongs on the plug.2. Measure the resistance value, with an ohmmeter,
between the jumpered AC plug and each exposed metal-lic cabinet part on the equipment such as screwheads,connectors, control shafts, etc. When the exposed metal-lic part has a return path to the chassis, the readingshould be between 1 MΩ and 5.2 MΩ. When the exposedmetal does not have a return path to the chassis, thereading must be infinity.
1.3. Leakage Current Hot Check(See Figure 1.)
1. Plug the AC cord directly into the AC outlet. Do not usean isolation transformer for this check.
2. Connect a 1.5 kΩ, 10 W resistor, in parallel with a 0.15 μFcapacitor, between each exposed metallic part on the setand a good earth ground, as shown in Figure 1.
3. Use an AC voltmeter, with 1 kΩ/V or more sensitivity, tomeasure the potential across the resistor.
4. Check each exposed metallic part, and measure the volt-age at each point.
5. Reverse the AC plug in the AC outlet and repeat each ofthe above measurements.
6. The potential at any point should not exceed 0.75 V RMS.A leakage current tester (Simpson Model 229 or equiva-lent) may be used to make the hot checks, leakage cur-rent must not exceed 1/2 mA. In case a measurement isoutside of the limits specified, there is a possibility of ashock hazard, and the equipment should be repaired andrechecked before it is returned to the customer.
Figure. 1
3
1.4. How to Discharge the E.Capacitor on Flash P.C.B.CAUTION:
1. Be sure to discharge the capacitor on FLASH P.C.B..2. Be careful of the high voltage circuit on FLASH P.C.B. when servicing.
[Discharging Procedure]1. Refer to the disassemble procedure and remove the necessary parts/unit.2. Install the insulation tube onto the lead part of resistor (ERG5SJ102:1kΩ /5W).
(an equivalent type of resistor may be used.)3. Place a resistor between both terminals of capacitor on the FLASH P.C.B. for approx. 5 seconds.4. After discharging, confirm that the capacitor voltage is lower than 10V using a voltmeter.
Fig. F1
4
2 Warning2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically
Sensitive (ES) DevicesSome semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-trostatically Sensitive (ES) Devices.
The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge(ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on yourbody by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-num foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.4. Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" can
generate electrical charge sufficient to damage ES devices.5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-ble conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective materialto the chassis or circuit assembly into which the device will be installed.CAUTION :
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) suf-ficient to damage an ES device).
2.2. How to Recycle the Lithium Ion Battery (U.S. Only)
5
2.3. Caution for AC Cord(For EB/GC)
2.3.1. Information for Your SafetyIMPORTANT
Your attention is drawn to the fact that recording of pre-recorded tapes or discs or other published or broadcastmaterial may infringe copyright laws.
WARNINGTo reduce the risk of fire or shock hazard, do not exposethis equipment to rain or moisture.
CAUTIONTo reduce the risk of fire or shock hazard and annoyinginterference, use the recommended accessories only.
FOR YOUR SAFETY DO NOT REMOVE THE OUTER COVERTo prevent electric shock, do not remove the cover. No userserviceable parts inside. Refer servicing to qualified servicepersonnel.
2.3.2. Caution for AC Mains LeadFor your safety, please read the following text carefully.
This appliance is supplied with a moulded three-pin mains plugfor your safety and convenience.A 5-ampere fuse is fitted in this plug.Should the fuse need to be replaced please ensure that thereplacement fuse has a rating of 5 amperes and it is approvedby ASTA or BSI to BS1362Check for the ASTA mark or the BSI mark on the body of thefuse.
If the plug contains a removable fuse cover you must ensurethat it is refitted when the fuse is replaced.If you lose the fuse cover, the plug must not be used until areplacement cover is obtained.A replacement fuse cover can be purchased from your localPanasonic Dealer.
If the fitted moulded plug is unsuitable for the socket outlet inyour home then the fuse should be removed and the plug cutoff and disposed of safety.There is a danger of severe electrical shock if the cut off plug isinserted into any 13-ampere socket.
If a new plug is to be fitted please observe the wiring code asshown below.If in any doubt, please consult a qualified electrician.
2.3.2.1. ImportantThe wires in this mains lead are coloured in accordance withthe following code:
As the colours of the wires in the mains lead of this appliancemay not correspond with the coloured markings identifying theterminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the ter-minal in the plug which is marked with the letter N or colouredBLACK.
The wire which is coloured BROWN must be connected to theterminal in the plug which is marked with the letter L or colouredRED.
Under no circumstances should either of these wires be con-nected to the earth terminal of the three pin plug, marked withthe letter E or the Earth Symbol.
2.3.2.2. Before UseRemove the Connector Cover as follows.
2.3.2.3. How to Replace the Fuse1. Remove the Fuse Cover with a screwdriver.
2. Replace the fuse and attach the Fuse cover.
Blue NeutralBrown Live
6
2.4. How to Replace the Lithium Battery2.4.1. Replacement Procedure
1. Remove the MAIN P.C.B.. (Refer to Disassembly Procedures.)2. Remove the Lithium battery (Ref. No. “B9101” at component side of MAIN P.C.B.) and then replace it into new one.
NOTE:This Lithium battery is a critical component. (Type No.: ML614 Manufactured by Energy Company, Panasonic Corporation.)It must never be subjected to excessive heat or discharge.It must therefore only be fitted in requirement designed specifically for its use.Replacement batteries must be of same type and manufacture.They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.Do not attempt to re-charge the old battery or re-use it for any other purpose.It should be disposed of in waste products destined for burial rather than incineration.
NOTE:Above caution is applicable for a battery pack which is for DMC-FZ100 series, as well.
7
3 Service Navigation3.1. IntroductionThis service manual contains technical information, which allow service personnel’s to understand and service this model.Please place orders using the parts list and not the drawing reference numbers.If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.
3.2. Service Navigation3.2.1. About lens block
• The image sensor (MOS SENSOR) unit which are connected to the lens unit with 3 screws. These screws are locked with thescrew locking glue, after performing the Optical tilt adjustment. During servicing, if one of MOS SENSOR fixing screws are loosened, the Optical tilt adjustment must be performed.(About the Optical tilt adjustment, refer to the “9.3.2 Adjustment Specifications” for details.)
NOTE:• It is necessary to use the “DSC_Tilt” software to allow the “Optical tilt adjustment”.• The Adjustment software “DSC_Tilt” is available at “TSN Website”. To download, click on “Support Information from NWBG/
VDBG-AVC”.
3.2.2. About VENUS FHD(IC6001) [Located on the Main P.C.B.]:• The VENUS FHD (IC6001) consists of two IC chips, which are fixed together with solder.
(The so called, “Package On Package” type IC.)NOTE:
• During servicing, do not press down hard on the surface of IC6001.
8
3.3. General Description About Lead Free Solder (PbF)The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for thisequipment in considering the globally environmental conservation.The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30°C (86°F) more than that of thenormal solder.Distinction of P.C.B. Lead Free Solder being used
Service caution for repair work using Lead Free Solder (PbF)• The lead free solder has to be used when repairing the equipment for which the lead free solder is used.
(Definition: The letter of “PbF” is printed on the P.C.B. using the lead free solder.)• To put lead free solder, it should be well molten and mixed with the original lead free solder.• Remove the remaining lead free solder on the P.C.B. cleanly for soldering of the new IC.• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the
lead free solder.• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30°C
(662±86°F).Recommended Lead Free Solder (Service Parts Route.)
• The following 3 types of lead free solder are available through the service parts route.RFKZ03D01KS-----------(0.3mm 100g Reel)RFKZ06D01KS-----------(0.6mm 100g Reel)RFKZ10D01KS-----------(1.0mm 100g Reel)
Note* Ingredient: tin (Sn) 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%
3.4. Important Notice 1:(Other than U.S.A. and Canadian Market)1. The service manual does not contain the following information because of issues servicing to component level without neces-
sary equipment/facilities.a. Schematic diagram, Block Diagram and P.C.B. layout of MAIN P.C.B..b. Parts list for individual parts for MAIN P.C.B..
When a part replacement is required for repairing MAIN P.C.B., replace as an assembled parts. (MAIN P.C.B.)2. The following category is/are recycle module part. please send it/them to Central Repair Center.
• MAIN P.C.B. (VEP56108A: P/PC/PU/EE/GC/GD/GK/GN/GT/SG): Excluding replacement of Lithium Battery.• MAIN P.C.B. (VEP56108B: EB/EF/EG/EP): Excluding replacement of Lithium Battery.
9
3.5. How to Define the Model Suffix (NTSC or PAL model)There are nine kinds of DMC-FZ100, regardless of the colours.
• a) DMC-FZ100 (Japan domestic model), DMC-FZ100SG• b) DMC-FZ100P/PC• c) DMC-FZ100EB/EF/EG/EP• d) DMC-FZ100EE• e) DMC-FZ100GT• f) DMC-FZ100GK• g) DMC-FZ100GD• h) DMC-FZ100GN• i) DMC-FZ100GC/PU
What is the difference is that the “INITIAL SETTINGS” data which is stored in Flash-ROM mounted on MAIN P.C.B..
3.5.1. Defining methods:To define the model suffix to be serviced, refer to the nameplate which is putted on the bottom side of the Unit.
NOTE:After replacing the MAIN P.C.B., be sure to achieve adjustment.The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-AVC” web-site in“TSN system”, together with Maintenance software.
10
3.5.2. INITIAL SETTINGS:After replacing the MAIN P.C.B., be sure to perform the initial settings after achieving the adjustment by ordering the following pro-cedure in accordance with model suffix of the unit.1. IMPORTANT NOTICE:
Before proceeding Initial settings, be sure to read the following CAUTIONS.
2. PROCEDURES:• Precautions: Read the above "CAUTION 1" and "CAUTION 2", carefully.• Preparation:
- Attach the Battery or AC Adaptor with a DC coupler to the unit.(Since this unit has built-in memory, it can be performed without inserting SD memory card.)
• Step 1. The temporary cancellation of “INITIAL SETTINGS”:Set the mode dial to “[ P ] (Program AE mode)”. While keep pressing “[ UP ] of Cursor button” and [ MOTION PICTURE ] button simultaneously, turn the Power on.
• Step 2. The cancellation of “INITIAL SETTINGS”:Press the [ PLAYBACK ] button, then playback the picture.Press “[ UP ] of Cursor button” and [ MOTION PICTURE ] button simultaneously, then turn the Power off.
• Step 3. Turn the Power on:Set the mode dial to “[ P ] (Program AE mode)”, and then turn the Power on.
• Step 4. Display the INITIAL SETTING:While keep pressing [ MENU/SET ] and “[ RIGHT ] of Cursor buttons” simultaneously, turn the Power off. The "INITIAL SETTINGS" menu is displayed.There are two kinds of “INITIAL SETTINGS” menu form as follows:
11
[CASE 1. After replacing MAIN P.C.B.][Except “EG, EF, EB and EP” models: (VEP56108A is used as a Main P.C.B.)]When MAIN P.C.B. has just been replaced, all of the model suffix is displayed as follows. (Three pages in total)
[Only “EG, EF, EB and EP” models: (VEP56108B is used as a Main P.C.B.)]When MAIN P.C.B. has just been replaced, only 7 model suffix are displayed as follows. (Two pages in total)
[CASE 2. Other than “After replacing MAIN P.C.B.”]
• Step 5. Choose the model suffix in “INITIAL SETTINGS”: (Refer to “CAUTION 1”)[Caution: After replacing MAIN P.C.B.]
The model suffix can been chosen, JUST ONE TIME.Once one of the model suffix have been chosen, the model suffix lists will not be displayed, thus, it can not be changed.Therefore, select the area carefully.
Select the area with pressing “[ UP ] / [ DOWN ] of Cursor buttons”.
12
• Step 6. Set the model suffix in “INITIAL SETTINGS”: • Press the “[ RIGHT ] of Cursor buttons”.• The only set area is displayed, and then press the “[ RIGHT ] of Cursor buttons” after confirmation.
(The unit is powered off automatically.)
• Step 7. CONFIRMATION:Confirm the display of “PLEASE SET THE CLOCK” in concernd language when the unit is turned on again.When the unit is connected to PC with USB cable, it is detected as removable media.(When the “GT” or “GK” model suffix is selected, the display shows “PLEASE SET THE CLOCK” in Chinese.)
1) As for your reference, major default setting condition is as shown in the following table.• Default setting (After “INITIAL SETTINGS”)
MODEL VIDEO OUTPUT LANGUAGE DATE REMARKSa) DMC-FZ100 (Japan domestic model) NTSC Japanese Year/Month/Dateb) DMC-FZ100P NTSC English Month/Date/Yearc) DMC-FZ100PU NTSC English Month/Date/Yeard) DMC-FZ100GD NTSC Korean Year/Month/Datee) DMC-FZ100GC PAL English Date/Month/Yearf) DMC-FZ100GT NTSC Chinese (traditional) Year/Month/Dateg) DMC-FZ100GK PAL Chinese (simplified) Year/Month/Dateh) DMC-FZ100EE PAL Russian Date/Month/Yeari) DMC-FZ100GN PAL English Date/Month/Yearj) DMC-FZ100PC NTSC English Month/Date/Yeark) DMC-FZ100SG PAL English Date/Month/Yearl) DMC-FZ100EG PAL English Date/Month/Year
m) DMC-FZ100EF PAL French Date/Month/Yearn) DMC-FZ100EB PAL English Date/Month/Yearo) DMC-FZ100EP PAL English Date/Month/Year
13
4 Specifications
14
5 Location of Controls and Components1 Lens2 Flash3 Self-Timer indicator
AF assist lamp4 Lens hood attachment part
5 [Q.MENU] button/Delete button6 [DISPLAY] button7 LCD monitor8 Flash open button9 Diopter adjustment dial10 Viewfinder11 [EVF/LCD] button12 [AF/AE LOCK] button
13 Rear dial
14 Playback button15 [MENU/SET] button
1 2 3
4
8
567
9 10 111213
141516
16 Cursor buttons
/ Self-Timer button
/ Function buttonAssign [REC] Mode menu to button. It is convenient to register [REC]Mode menu that is used often.[FILM MODE]/[ASPECT RATIO]/[QUALITY]/[METERING MODE]/[WHITE BALANCE]/[I.EXPOSURE]/[GUIDE LINE]/[ REC AREA]/[REMAINING DISP.]
/ ISO
/ Exposure compensation/Auto Bracket/Flash output adjustment
15
17 Stereo microphone18 Zoom lever19 Shutter button20 Motion picture button21 Burst Mode button22 Power lamp23 Camera ON/OFF switch24 Mode dial25 Hot Shoe
26 [MIC/REMOTE] terminal door27 Shoulder strap eyelet28 [MIC/REMOTE] socket29 [HDMI] socket30 [AV OUT/DIGITAL] socket31 Terminal door32 [FOCUS] button33 Focus selector switch
CUSTM
25
18
19
21
20
222324
17
MIC
REMOTE
AV
OU
T/D
IGIT
AL
27
28
26
3029
3132
33
34 Speaker35 Lens barrel
36 Release lever37 Tripod receptacle
When you use a tripod, make sure the tripodis stable when the camera is attached to it.
38 Card/Battery door
39 DC coupler coverWhen using an AC adaptor, ensure thatthe Panasonic DC coupler (DMW-DCC6;optional) and AC adaptor (DMW-AC8PP;optional) are used.Always use a genuine Panasonic ACadaptor (DMW-AC8PP; optional).We recommend you use a battery withsufficient battery power or the AC adaptorwhen recording motion pictures.If while recording motion pictures using theAC adaptor and the power supply is cut offdue to a power outage or if the AC adaptoris disconnected etc., the motion picturebeing recorded will not be recorded.
34 35
37 38
39
36
16
Mode switching
Basic
Selecting the [REC] Mode
Turn the camera on.
The power lamp lights when you turn thisunit on .
Switching the mode by rotating themode dial.
Align a desired mode with part .Rotate the mode dial slowly and surely toadjust to each mode. (The mode dialrotates 360 )
Basic
Intelligent Auto Mode
The subjects are recorded using settings automatically selected by thecamera.
Program AE Mode
The subjects are recorded using your own settings.
CUSTM
CUST
M
Advanced
Advanced Scene Mode
Aperture-Priority AE Mode
The shutter speed is automatically determined by the aperture value you set.
Shutter-Priority AE Mode
The aperture value is automatically determined by the shutter speed you set.
Manual Exposure Mode
The exposure is adjusted by the aperture value and the shutter speed whichare manually adjusted.
Creative Motion Picture Mode
Record motion picture with manual settings.
Custom Mode
Use this mode to take pictures with previously registered settings.
Scene Mode
This allows you to take pictures that match the scene being recorded.
My Color Mode
Use this mode to check coloring effects, select a color mode from amongtwelve color modes, and then take pictures.
Portrait Mode
Use this mode to take pictures of people.
Scenery Mode
Use this mode to take pictures of scenery.
Sports Mode
Use this mode to take pictures of sporting events, etc.
Close-up Mode
Use this mode to take pictures of a close-by subject.
Night Portrait Mode
Use this mode to take pictures of night scenes and people against night timescenery.
17
Preparation
About the Battery
The camera has a function for distinguishing batteries which can be used safely. Thededicated battery supports this function. The only batteries suitable for use with thisunit are genuine Panasonic products and batteries manufactured by other companiesand certified by Panasonic. (Batteries which do not support this function cannot beused). Panasonic cannot in any way guarantee the quality, performance or safety ofbatteries which have been manufactured by other companies and are not genuinePanasonic products.
It has been found that counterfeit battery packs which look very similar to thegenuine product are made available to purchase in some markets. Some of thesebattery packs are not adequately protected with internal protection to meet therequirements of appropriate safety standards. There is a possibility that thesebattery packs may lead to fire or explosion. Please be advised that we are notliable for any accident or failure occurring as a result of use of a counterfeitbattery pack. To ensure that safe products are used we would recommend that agenuine Panasonic battery pack is used.
18
6 Service Mode6.1. Error Code Memory Function
1. General descriptionThis unit is equipped with history of error code memory function, and can be memorized 16 error codes in sequence from thelatest. When the error is occurred more than 16, the oldest error is overwritten in sequence.The error code is not memorized when the power supply is shut down forcibly (i.e.,when the unit is powered on by the battery,the battery is pulled out) The error code is memorized to FLASH-ROM when the unit has just before powered off.
2. How to displayThe error code can be displayed by ordering the following procedure:
• Preparation:1. Attach the Battery or AC Adaptor with a DC coupler to the unit.NOTE:*Since this unit has built-in memory, it can be performed without inserting SD memory card.
• Step 1. The temporary cancellation of “INITIAL SETTINGS”:Set the mode dial to “[ P ] (Program AE mode)”.While keep pressing “[ UP ] of Cursor button” and [ MOTION PICTURE ] button simultaneously, turn the Power on.
• Step 2. Execute the error code display mode:Press the “[ LEFT ] of Cursor button”, [ MENU/SET ] button and [ MOTION PICTURE ] button simultaneously.The display is changed as shown below when the above buttons are pressed simultaneously.Normal display → Error code display → Operation history display → Normal display → .....
Example of Error Code Display
19
• 3. Error Code ListThe error code consists of 8 bits data and it shows the following information.
20
Important notice about "Error Code List"1) About "*" indication:The third digit from the left is different as follows.
- In case of 0 (example: 18001000)When the third digit from the left shows "0", this error occurred under the condition of INITIAL SETTINGS has been completed.It means that this error is occurred basically at user side.
- In case of 8 (example: 18801000)When the third digit from the left shows "8", this error occurred under the condition of INITIAL SETTINGS has beenreleased. (Example; Factory assembling-line before unit shipment, Service mode etc.)It means that this error is occurred at service side.
2) About "?" indication: ("18*0 0?01" to "18*0 0?50"):The third digit from the right shows one of the hexadecimal ("0" to "F") character.
• 4. How to exit from Error Code display mode:Simply, turn the power off. (Since Error code display mode is executed under the condition of temporary cancellation of "INI-TIAL SETTINGS", it wake up with normal condition when turn off the power.)
NOTE:The error code can not be initialized.
6.2. ICS (Indication of additional Camera Settings when picture was taken)function
1. General descriptionThis unit is equipped with ICS (ICS: Indication of additional Camera Settings when picture was taken) function by playing backthe concerned picture on the LCD display. (This function is achieved by utilizing "maker note" data stored in Exif data area of recorded picture file.) To proceed failure diagnosis, use this ICS function together with "displaying the recorded picture with picture information "function.NOTE:
• The ICS function operates with a picture which is only taken with the same model. (It may not be displayed when the picturewas taken with other model.)
• Since Exif data is not available after the picture is edited by PC, the ICS function may not be activated.
2. How to displayThe ICS data is displayed by ordering the following procedure:
• Preparation:1. Attach the Battery or AC Adaptor with a DC coupler to the unit.NOTE:Since this unit has bult-in memory, it can be performed without inserting SD memory card.
• Step 1. The temporary cancellation of "INITIAL SETTINGS":Set the mode dial to “[ P ] (Program AE mode)”. While keep pressing “[ UP ] of Cursor button” and [ MOTION PICTURE ] button simultaneously, turn the Power on.
• Step 2. Execute the ICS display mode:Press the [ PLAYBACK ] button, then playback the picture. Press the "[ LEFT ] of Cursor button", [ MENU/SET ] button and [ MOTION PICTURE ] button simultaneously.Press the [ DISPLAY ] button, 3 times. The display condition is changed as shown below when the [ DISPLAY ] button is pressed.
Code display → Code + Picture display (1) → Code + Picture display (2) → ICS display → Code display .....
21
3. How to read
4. How to exit:Simply, turn the power off. (Since ICS function is executed under the condition of temporary cancellation of "INITIAL SETTINGS", it wake up with normal condition when turn off the power.)
22
7 Service Fixture & Tools7.1. Service Fixture and ToolsThe following Service Fixture and tools are used for checking and servicing this unit.
23
7.2. When Replacing the Main P.C.B.After replacing the MAIN P.C.B., it is necessary to use the "DIAS” software to allow the release of adjustment flag(s). The Adjustment software “DIAS” is available at “TSN Website”. To download, click on “Support Information from NWBG/VDBG-AVC”. *DIAS (DSC Integrated Assist Software)
7.3. Service PositionThis Service Position is used for checking and replacing parts. Use the following Extension cables for servicing.
Table S1 Extension Cable List
CAUTION-1. (When servicing FLASH P.C.B.)1. Be sure to discharge the capacitor on FLASH P.C.B..
Refer to “HOW TO DISCHARGE THE CAPACITOR ON FLASH P.C.B.”.The capacitor voltage is not lowered soon even if the AC Cord is unplugged or the battery is removed.
2. Be careful of the high voltage circuit on FLASH P.C.B..3. DO NOT allow other parts to touch the high voltage circuit on FLASH P.C.B..
No. Parts No. Connection Form1 VFK1906 PS9001 (MAIN) - PP8001 (FLASH) 20PIN B to B2 VFK1953 FP9005 (MAIN) - LENS UNIT 40PIN 0.5 FFC
24
8 Disassembly and Assembly Instructions8.1. Disassembly Flow ChartThis is a disassembling chart.When assembling, perform this chart conversely.
8.2. P.C.B. Location
25
8.3. Disassembly Procedure
No. Item Fig Removal1 Rear Case Unit (Fig. D1) Card
Battery3 Screws (A)2 Screws (B)
(Fig. D2) Shoe Spring2 Screws (C)P9001(Connector)P9003(Connector)FP9003(Flex)Rear Case Unit
2 Main P.C.B. (Fig. D3) 1 Screw (D)3 Screws (E)FP9001(Flex)FP9002(Flex)FP9004(Flex)FP9005(Flex)PS9001(Connector)FP9006(Flex)FP9008(Flex)FP9010(Flex)P9005(Connector)Jack HolderMain P.C.B.
3 Top Operation Unit (Fig. D4) 1 Screw (F)Top Operation Unit
4 Battery Case Unit (Fig. D5) 1 Screw (G)P8003(Connector)P8004(Connector)Battery Case Unit
5 EVF Unit Flash Unit
(Fig. D6) 1 Screw (H)EVF UnitFlash Unit
6 Lens Unit (Fig. D7) Lens Heat Sink2 Screws (I)
(Fig. D8) Lens Unit7 AF LED P.C.B. (Fig. D9) 1 Screw (J)
Strap Holder (R)Side Frame (R)Jack Cover1 Screw (K)FP9301(Flex)
(Fig. D10) Remote CoverRemote HolderAF Light CaseAF LED P.C.B.
8 AF/MF Flex Unit (Fig. D11) 2 Locking tabsAF/MF OP Support
(Fig. D12) 2 Locking tabsAF/MF OP Slide KnobAF/MF OP ButtonAF/MF OP Spring UnitAF/MF OP Case UnitAF/MF Flex Unit
9 Flash P.C.B. (Fig. D13) Condensor Cover1 Locking tab1 Screw (L)2 Hanging partsFlash P.C.B.
(Fig. D14) Discharge of the E.capacitor
10 EVF Unit (Fig. D15) 2 Locking tabsEVF Unit
11 Hot Shoe UnitECM Flex UnitFlash Unit
(Fig. D16) 3 Screws (M)2 Screws (N)Hot Shoe Unit
(Fig. D17) 4 Locking tabsFlash Case TopFlash ShaftFlash Pop Up Spring
(Fig. D18) 2 Locking tabsFlash UnitMIC DamperMIC CushionECM Flex Unit
12 Speaker (Fig. D19) 1 Screw (O)Wire Fix Tape1 Hanging part
(Fig. D20) Speaker Fix PlateSpeaker
13 LCD UnitHinge P.C.B.
(Fig. D21) 2 Screws (P)Wire Fix TapeHinge Arm Cover TopHinge Arm Cover Bottom2 Screws (Q)
(Fig. D22) 2 RibsHinge Plate1 Screw (R)LCD UnitHinge P.C.B.
14 LCD Unit (Fig. D23) 4 Screws (S)6 Locking tabsLCD Case BottomLCD Hinge UnitFP4101(Flex)LCD Case TopLCD Unit
No. Item Fig Removal
26
8.3.1. Removal of the Rear Case Unit
(Fig. D1)
(Fig. D2)
27
8.3.2. Removal of the Main P.C.B.
(Fig. D3)
8.3.3. Removal of the Top Operation Unit
(Fig. D4)
8.3.4. Removal of the Battery Case Unit
(Fig. D5)
28
8.3.5. Removal of the EVF Unit and FlashUnit
(Fig. D6)
8.3.6. Removal of the Lens Unit
(Fig. D7)
(Fig. D8)
8.3.7. Removal of the AF LED P.C.B.
(Fig. D9)
29
(Fig. D10)
8.3.8. Removal of the AF/MF Flex Unit
(Fig. D11)
(Fig. D12)
30
8.3.9. Removal of the Flash P.C.B.
(Fig. D13)
(Fig. D14)
31
8.3.10. Removal of the EVF Unit
(Fig. D15)
8.3.11. Removal of the Hot Shoe Unit, ECMFlex Unit and Flash Unit
(Fig. D16)
32
(Fig. D17)
(Fig. D18)
8.3.12. Removal of the Speaker
(Fig. D19)
33
(Fig. D20)
8.3.13. Removal of the LCD Unit and HingeP.C.B.
(Fig. D21)
34
(Fig. D22)
8.3.14. Removal of the LCD Unit
(Fig. D23)NOTE: (When Installing)
Make sure to confirm the following points when installing:• The Sscrew is tightened enough.• Installing conditions are fine. (No distortion, no abnormal-
space.)• No dust and/or dirt on Lens surfaces.• LCD image is fine. (No dust and dirt on it, and no gradient
images.)
35
8.4. Lens Disassembly ProcedurePrecaution:
1. Do not remove the MOS SENSOR unit when disassem-bling or re-assembling the lens in order to maintain itclean.The screw fitting the MOS SENSOR unit to the masterflange unit is fixed by the bond lock with the adjustment ofthe installation angle of the MOS SENSOR unit againstthe lens (optical axis adjustment) finished.When remove it, refer to item "9.5.".
2. Keep dust or dirt away from the lens.To remove dirt or dust from the lens, blow with dry air.
3. Do not touch the lens surface.4. Use lens cleaning KIT (VFK1900BK).5. Apply grease as shown on item "8.4.5" and "8.4.6" in the
figure.
8.4.1. Removal of the Zoom Motor Unit
8.4.2. Removal of the 1st Lens Frame Unitand 2nd Lens Frame Unit
1. Unscrew the 1 screw (B).2. Remove the cam stopper.
36
3. Turn the cam frame unit or gear part of cam frame unit inthe direction of arrow fully.
4. Remove the 1st lens frame unit and 2nd lens frame unit.
37
8.4.3. Removal of the Master Flange Unit1. Remove the flex from the connector.2. Detach the flex from 1 rib of master flange unit.3. Remove the 4 solders.4. Unscrew the 3 screws (C).5. Remove the master flange unit in the direction of arrow.
38
8.4.4. Removal of the Cam Frame 8.4.5. Removal of the Focus Motor Unit1. Detach the flex from 2 ribs of middle frame unit.2. Unscrew the 2 screws (D).
39
8.4.6. Removal of the 3rd Lens FrameUnit and 4th Lens Frame Unit
40
8.5. Removal of the MOS SENSOR UnitWhen remove the MOS SENSOR unit once (the screw(E) isloosened even a little), the optical tilt adjustment is required.When loosen the screw(E), necessary the optical tilt adjustmentat the end of assembling. (Refer to item "9.3.2.") To prevent the MOS SENSOR unit from catching the dust anddirt, do not remove the MOS SENSOR unit except for replac-ing.
41
9 Measurements and Adjustments9.1. IntroductionWhen servicing this unit, make sure to perform the adjustments necessary based on the part(s) replaced.Before disassembling the unit, it is recommended to back up the camera data stored in flash-rom as a data file. IMPORTANT NOTICE (After replacing the MAIN P.C.B.)
After replacing the MAIN P.C.B., it is necessary to use the “DIAS” software to allow the release of adjustment flag(s).The Adjustment software “DIAS” is available at “TSN Website”. To download, click on “Support Information from NWBG/VDBG-AVC”.*DIAS (DSC Integrated Assist Software)
NOTE: (When replacing the Lens unit, Master flange unit and MOS SENSOR unit)• When the MOS SENSOR unit is unavoidably removed for Lens unit, Master flange unit and MOS SENSOR unit replaced, an
optical adjustment is necessary after parts are exchanged.• The adjustment software (DSC_Tilt) is necessary to execute an optical tilt adjustment.
9.2. Before Disassembling the unit9.2.1. Initial Setting ReleaseThe cameras specification are initially set in accordance with model suffix (such as EB, EG, GK, GC, and so on.).Unless the initial setting is not released, an automatic alignment software in the camera is not able to be executed when the align-ment is carried out.Note:
The initial setting should be again done after completing the alignment. Otherwise, the camera may not work properly.Therefore as a warning, the camera display a warning symbol “ ! ” on the LCD monitor every time the camera is turned off.Refer to the procedure described in “3.5.2 INITIAL SETTINGS” for details.
[ How to Release the camera initial setting ]Preparation:
1. Attach the Battery or AC Adaptor with a DC coupler to the unit.(Since this unit has built-in memory, it can be performed without inserting SD memory card.)
Step 1. Temporary cancellation of “INITIAL SETTINGS”:Set the mode dial to “[ P ] (Program AE mode)”.While keep pressing “[ UP ] of Cursor button” and [ MOTION PICTURE ] button simultaneously, turn the Power on.Step 2. Cancellation of “INITIAL SETTINGS”:Press the [ PLAYBACK ] button, then playback the picture.Press “[ UP ] of Cursor button” and [ MOTION PICTURE ] button simultaneously. (The camera will beep after this.)Turn the Power off. (The warning symbol “ ! ” is displayed on the LCD monitor.)
42
9.2.2. Flash-Rom Data BackupWhen trouble occurs, it is recommended to backup the Flash-rom data before disassembling the unit.There are two kinds of Flash-rom data backup methods:[ ROM_BACKUP (Method of Non-PC backup) ]
1. Insert the SD-card into the camera.2. Set the camera to “Temporary cancellation of the initial
settings”. 3. Select the “SETUP” menu.
From the “SETUP” menu, select “ROM BACKUP”.NOTE:
This item is not listed on the customer's “SETUP”menu.
4. When this “ROM_BACKUP” item is selected, the follow-ing submenus are displayed.
[ DSC Integrated Assist Software (Method of Using PC) ]Same as TATSUJIN software for previous models.
9.2.3. Light BoxIf using VFK1164TDVLB Light Box, remove the lens connectionring by loosing three hexagon screws.
43
9.3. Details of Electrical Adjustment9.3.1. How to execute the Electrical AdjustmentIt is not necessary to connect the camera to a PC to perform adjustments.“Flag reset operation” and “Initial setting operation” are required when carrying out the alignment, follow the procedure below.
9.3.1.1. Startup Electrical Adjustment mode1. Release the initial settings.2. Insert a recordable SD card.
(Without a SD card, the automatic adjustment can notexecuted.)
3. Procedure to set the camera into adjustment mode:a. Set the mode dial to “[ P ] (Program AE mode)”.b. Turn the Power off.c. Turn the Power on pressing [ MENU/SET ] and
[ MOTION PICTURE ] simultaneously.LCD monitor displays “SERVICE MODE”.(Refer toFig. 3-1)
9.3.1.2. Status Adjustment Flag SettingReset (Not yet adjusted) the status flag condition.
1. After pressing the [ DISPLAY ] button, the LCD monitordisplays the Flag status screen (Refer to Fig.3-2)
2. Select item by pressing the Cursor buttons. (Gray cursoris moved accordingly.)
3. Press the [ Delete ] button.NOTE:
The selected item's flag has been changed from “F (green)” to “0 (yellow)”.
*Flag conditions:F (green)means that the alignment has been completed and thestatus flag condition is set. In this case, the flag conditionshould be reset, if you try to carry out the automatic align-ment.0 (yellow)means that the alignment has been not “completed” andthe status flag condition is “reset”. In this case, automaticalignment is available.
• In case of setting the status flag into set condition again without completion of the alignment, the status flag should be SET byusing PC, or UNDO by using ROM BACKUP function.
44
9.3.1.3. Execute Adjustment(In case of “OIS Adjustment”)
1. Perform step “9.3.1.1.” to “9.3.1.2.”, to reset the OIS flagstatus “F” (Set) to “0” (Reset)
2. Press [ DISPLAY ] button after Flag reset.OIS Adjustment screen is displayed on the LCD panel.(Refer to Fig.3-3)
3. Press the [ Shutter ] button. The adjustment will startautomatically.
4. When the adjustment is completed successfully, adjust-ment report menu appears with Green OK on the LCDmonitor. (Refer to Fig.3-4)
9.3.1.4. Attention point during Adjustment1. Step “9.3.1.3.” procedure shows OIS adjustment as an
example. To perform the adjustment, refer to the “9.3.2.Adjustment Specifications” table which shows key pointfor each adjustment.
2. Do not move the light box, the camera or the chart whileadjusting. If one of these is moved accidentally, start theadjustment again.
3. Do not press any buttons/keys until the default menu(Fig.3-5) is displayed on the LCD monitor. Otherwise,adjustment data may not be stored properly.
4. If the adjustment is interrupted accidentally, the alignmentdata may not be properly saved in the Flash-rom.
9.3.1.5. Finalizing the Adjustment1. Several adjustment flags can be reset (“F” into “0”) at the same time. In this case, when the adjustment has been completed,
the screen will change showing the adjustment for the next item until all reset items are completed. Also, when the shutter button is pressed, the screen jump to the next adjustment item.
2. To cancel the adjustment mode while in the process of performing the adjustment, follow this procedures.(1) Press [ Delete ] button.(2) Press [ RIGHT ] of Cursor button.NOTE:
• If adjustment is cancelled with above procedure, adjustment is not completed. Make sure to adjust it later.• Adjustment software “DIAS” is able to control the status of the adjustment flags.
45
9.3.2. Adjustment SpecificationsThe following matrix table shows the relation between the replaced part and the Necessary Adjustment.When a part is replaced, make sure to perform the necessary adjustment(s) in the order indicated.The table below shows all the information necessary to perform each adjustment.
46
47
9.4. After Adjustment9.4.1. Initial SettingSince the initial setting has been released to execute the built-in adjustment software, it should be set up again before shipping thecamera to the customer.Refer to the procedure described in “3.5.2. INITIAL SETTINGS” for details.
[ IMPORTANT ] 1. The initial setting should be done again after completing the alignment. Otherwise, the camera will not work properly.
Therefore as a warning, the camera display a warning symbol “ ! ” on the LCD monitor every time the camera is turned off.2. Confirm that status of all adjustment flag show “F”. Even if one of the adjustment flag shows “0”, initial setting programmed is
never executed.3. Adjustment software “DIAS” is able to control the status of the adjustment flags.
The Adjustment software “DIAS” is available at “TSN Website”, therefore, access to “TSN Website” at “Support Informationfrom NWBG/VDBG-AVC”.
48
10 Maintenance10.1. Cleaning Lens, Viewfinder and LCD PanelDo not touch the surface of lens, Viewfinder and LCD Panel with your hand.When cleaning the lens, use air-Blower to blow off the dust.When cleaning the LCD Panel, dampen the lens cleaning paper with lens cleaner, and the gently wipe the its surface.Note:
The Lens Cleaning KIT ; VFK1900BK (Only supplied as 10 set/Box) is available as Service Aid.
49
S-1
S1. About Indication of The Schematic Diagram ............................ S-1S1.1. Important Safety Notice......................................................... S-1
S2. Voltage Chart ........................................................................... S-2S2.1. Flash P.C.B. .......................................................................... S-2
S3. Block Diagram .......................................................................... S-3S3.1. Overall Block Diagram .......................................................... S-3
S4. Schematic Diagram .................................................................. S-4S4.1. Interconnection Diagram ....................................................... S-4S4.2. Flash Schematic Diagram ..................................................... S-5S4.3. Mic Jack Schematic Diagram ................................................ S-6S4.4. AF MF Flex Schematic Diagram ........................................... S-7S4.5. Hinge Schematic Diagram .................................................... S-7S4.6. Lens Flex Schematic Diagram .............................................. S-8
S5. Print Circuit Board .................................................................... S-9S5.1. Flash P.C.B. .......................................................................... S-9S5.2. Mic Jack P.C.B. ..................................................................... S-9S5.3. AF MF Flex P.C.B. ............................................................... S-10
S5.4. Hinge P.C.B. ........................................................................ S-10S5.5. Lens Flex P.C.B. .................................................................. S-11
S6. Replacement Parts List .......................................................... S-13
S7. Exploded View ....................................................................... S-17S7.1. Frame and Casing Section.................................................. S-17S7.2. Camera Lens Section.......................................................... S-18S7.3. Packing Parts and Accessories Section (1) ........................ S-19S7.4. Packing Parts and Accessories Section (2) ........................ S-20
Table of contents
Service ManualDSC1007045CE
Diagrams and ReplacementParts List
Vol. 1
(K)...........Black TypeColour
Model No.DMC-FZ100PDMC-FZ100PCDMC-FZ100PUDMC-FZ100EBDMC-FZ100EEDMC-FZ100EFDMC-FZ100EG
DMC-FZ100EPDMC-FZ100GCDMC-FZ100GDDMC-FZ100GKDMC-FZ100GNDMC-FZ100GTDMC-FZ100SG
Digital Camera
Name of Signal
OFTR FEP This signal is connectedto the FEP schematic diagram.
Circuit name being connected.
6.Use the parts number indicated on the Replacement Parts List .
7.Indication on Schematic diagrams:
5.The voltage being indicated here may be include observational-error (deviation) due tointernal-resistance and/or reactance of equipment. Therefore, handle the valueindicated on here as reference.
4.Although the voltage and waveform available on here is measured with standard frame,it may be differ from actual measurement due to modification of circuit and so on.
3.The voltage being indicated on the schematic diagram is measured in"Standard-Playback" mode when there is no specify mode is mentioned.
2.It is only the "Test Round" and no terminal (Pin) is available on the P.C.B.when the TP (Test Point) indicated as " " mark.
1.Although reference number of the parts is indicated on the P.C.B. drawing and/orschematic diagrams, it is NOT mounted on the P.C.B. when it is displayed with "$" mark.
FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE.COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS
S1. About Indication of The Schematic DiagramS1.1. Important Safety Notice
S-2
Note) Indicated voltage values are the standard values for the unit measured by the DC electronic circuit tester (high-impedance) with the chassis taken as standard. Therefore, there may exist some errors in the voltage values, depending on the internal impedance of the DC circuit tester.
S2.1. Flash P.C.B.
S2. Voltage Chart
REF No. PIN No. POWER ONQ8004 1 8Q8004 2 8Q8004 3 0Q8004 4 0Q8004 5 8Q8004 6 8
QR8001 1 0QR8001 2 4.8QR8001 3 0QR8001 4 5.2QR8001 5 4.8QR8001 6 0QR8002 E 0QR8002 C 4.8QR8002 B 0QR8003 E 0QR8003 C 0QR8003 B 3
S-3
S3. Block DiagramS3.1. Overall Block Diagram
DMC-FZ100 OVERAL BLOCK DIAGRAM
MAICO14MAFE
FOCUSIRIS
SDCARD
(POWER SUPPLY)BATTERY
REAR OPERATION UNIT
OIS UNIT
IC9101SYSTEM ICMOTOR DRIVE,OIS DRIVE&PRE PROCESS
IC6001VENUS FHD
CAMERA PROCESSJ-PEG COMP/EXPANDSMEDIA I/FUSB I/FMAIN MICROPROCESSOR
FLASH
TOP OPERATION UNITIC1001POWER
SHUTTER
IC9101SYSTEM IC
ZOOM
OIS CONTROLLENS DRIVELCD DRIVESDRAM/2G-bitNAND FLASH ROM/512M-bit
AV OUT / DIGITALTERMINAL
EXTFLASH
IC7103,7104GYRO AMP
IC9101SYSTEM ICMICROPHONE AMPSPEAKER CONTROL
SPEAKER
X6001(24MHz)
X9101(32.768kHz)
VIDEO OUT
IC1031,1061,1062IC1092,9103REGULATOR
IC9601HDMI DRIVER
HDMITERMINAL
IC7101GYRO SENSOR Y
IC7102GYRO SENSOR X
IC6003FeRAM
IC9602REGULATOR
COLOR LCDPANEL
COLOR EVF
3.0" PANEL 461k dots
0.2" PANELEQUIVALENT TO202k dots
MIC/REMOTETERMINAL
STEREOMICROPHONE
IC5001MPX/DEMPX
(25mm ~ 600mm/4:3)
ECM(L)
ECM(R)
IC1033DC/DC CONV.
S-4
S4. Schematic DiagramS4.1. Interconnection Diagram
MAIN P.C.B.(FOIL SIDE)
: (COMPONENT SIDE)
DMC-FZ100 INTERCONNECTION DIAGRAM
FP90
01V
DD
33A
VD
DV
DD
41V
DD
12V
DD
12V
DD
12V
DD
18P
SV
SC
KV
DG
ND
MC
LKG
ND
GN
DS
DO
DA
1MG
ND
SD
OD
A0P
SD
OD
A2M
GN
DS
DO
CA
PS
DO
DB
3MG
ND
SD
OD
A3P
SD
OC
BM
GN
DS
DO
DB
2PS
DO
DB
0MG
ND
SD
OD
B1P
GN
D
MO
S T
HE
RM
OA
VD
DA
VD
DG
ND
VD
D12
VD
D12
VD
D18
GN
DS
CS
SI
HD
GN
DG
ND
RS
TNG
ND
SD
OD
A1P
SD
OD
A0M
GN
DS
DO
DA
2PS
DO
CA
MG
ND
SD
OD
B3P
SD
OD
A3M
GN
DS
DO
CB
PS
DO
DB
2MG
ND
SD
OD
B0P
SD
OD
B1M
GN
D
59 57 55 53 51 49 47 45 43 41 39 37 35 33 31 29 27 25 23 21 19 17 15 13 11 9 7 5 3 1
60 58 56 54 52 50 48 46 44 42 40 38 36 34 32 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2
FP
9006
AF
LE
D A
AF
LE
D K
MIC
GN
DM
IC G
ND
MIC
RM
IC L
MIC
GN
DR
EM
OT
EA
F O
ND
GN
DA
FM
F B
AF
MF
A
12 11 10 9 8 7 6 5 4 3 2 1
P9005
STB OPEND GND1
2
P90
03
D G
ND
LCD
TA
IME
N21
FP
9004
22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
2R5V
GN
DN
RE
SE
TC
LOC
KH
SY
NC
VS
YN
CV
ALI
DD
ATA
0D
ATA
1D
ATA
2D
ATA
35V
DAT
A4
DAT
A5
DAT
A6
DAT
A7
SD
ATS
OU
TS
CLK
SE
NG
ND
5V
FP
9003
LCD
SW
1G
ND
GN
DG
ND
LCD
SD
OU
TLC
DH
DLC
D C
LKLC
DO
UT
1LC
DO
UT
3LC
DO
UT
5LC
DO
UT
7LC
DO
UT
9LC
DO
UT
11LC
DO
UT
13LC
DO
UT
15D
3VB
L-
GN
DG
ND
GN
DLC
D C
SLC
D S
CK
LCD
VD
LCD
OU
T0
LCD
OU
T2
LCD
OU
T4
LCD
OU
T6
LCD
OU
T8
LCD
OU
T10
LCD
OU
T12
LCD
OU
T14
D2R
5VB
L+
1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33
2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32
FP
9005
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
PS
9001
FRA
ME
GN
DFR
AM
E G
ND
FRA
ME
GN
DP
W 5
R2V
UN
RE
G G
ND
UN
RE
G G
ND
UN
RE
G G
ND
STB
PW
M O
UT
FLA
SH
TR
GS
TB C
HG
LV
D G
ND
D G
ND
D G
ND
INT
STB
ON
LD
GN
DD
GN
DD
GN
DU
NR
EG
UN
RE
GU
NR
EG
20 19 18 17 16 15 14 13 12 11
1 2 3 4 5 6 7 8 9 10
FP
9008
ST
XS
TX
NC
NC
NC
NC
ST
RT
TL
ST
RX
DS
TT
XD
FR
AM
E G
ND
FR
AM
E G
ND
FR
AM
E G
ND
12 11 10 9 8 7 6 5 4 3 2 1
FP
9010
MIC
GN
DM
IC L
INM
IC R
INM
IC G
ND
4 3 2 1
P90
01
SP
+S
P-
21
FP9002181716151413121110987654321
CMD DIAL F1CMD DIAL F0
KURUPOND GND
POWER LED KPOWER LED A
POWER SWBURST SHUTTER SEL
AD3MOVIE SEL
A3R1VAD2
D GNDWIDE
ZOOM SPD SELTELE
SHUTTER 1SHUTTER 0
FP
9302
AF
MF
AA
FM
F B
D G
ND
AF
ON
RE
MO
TE
MIC
GN
DM
IC L
MIC
RM
IC G
ND
MIC
GN
DA
F L
ED
KA
F L
ED
A
1 2 3 4 5 6 7 8 9 10 11 12
FP9301D GNDD GNDAF ON
AFMF AAFMF BD GND
123456
PP8001
20 19 18 17 16 15 14 13 12 11
1 2 3 4 5 6 7 8 9 10
P8003
LAMP+LAMP-2
1
P8004
UNREG GNDTRG IN2
1
VSC1NC2N
VCIX2CXPVCM
VCOMLVSS1VDDL
HSYNCDG0DG2DG4DG6DR0DR2DR4DR6SDA
SCENC3PC4PVGL
C1PC2P
VSS2VCICXN
VCOMHVGM
VDDIO1VSYNCDCLKDG1DG3DG5DG7DR1DR3DR5DR7SCLVGHC3NC4N
45434139373533312927252321191715131197531
4442403836343230282624222018161412108642
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
LENSUNITMAICO
(MOS/AFE)
FLASH P.C.B.(FOIL SIDE)
AF LED P.C.B.(FOIL SIDE)
LCD P.C.B.(FOIL SIDE)
MIC JACK FLEX
TOP OPERATION UNIT
(STEREO MICROPHONE)
SPEAKER
HOT SHOE UNIT
EVF
FLASHUNIT
LCD UNIT
LCD HINGE UNIT
AF MF FLEX UNIT
FLASH POP DET.
HINGE DET.
AB
S(Z
EN
C2)
LED
CO
NT
(Z1
LED
)A
BS
(ZE
NC
1)E
NC
VC
C(D
2R9V
)LE
D C
ON
T(Z
2 LE
D)
EN
C V
CC
(D2R
9V)
ZM
2(D
CM-
)Z
M2(
DC
M-
)Z
M1(
DC
M+
)Z
M1(
DC
M+
)E
NC
VC
C(D
2R9V
)A
BS
(FH
P)
LED
CO
NT
(FH
P L
ED
)E
NC
VC
C(D
2R9V
)A
BS
(ZH
P)
LED
CO
NT
(ZH
P L
ED
)FA
N(F
MA
N)
FB
N(F
MB
N)
FAP
(FM
AP
)F
BP
(FM
BP
)Y
DR
V+
(Y D
R+
)Y
HI -
(YV
H-
)Y
HO
+(Y
VO
+)
Y H
I+(Y
VH
+)
Y H
O-
(YV
O-
)Y
DR
V-
(Y D
R-
)S
T3(
IRIS
BP
)S
T1(
IRIS
AP
)S
T4(
IRIS
BN
)S
T2(
IRIS
AN
)S
H-
(SH
UT
OU
T1)
SH-
(SH
UT
OU
T1)
SH
+(S
HU
T O
UT
2)S
H+
(SH
UT
OU
T2)
X D
RV-
(X D
R-
)X
DR
V+
(X D
R+
)X
HI-
(XV
H-
)X
HO
+(X
VO
+)
X H
I+(X
VH
+)
X H
O-
(X V
O-
)
FRA
ME
GN
DFR
AM
E G
ND
FRA
ME
GN
DP
W 5
VU
NR
EG
GN
DU
NR
EG
GN
DU
NR
EG
GN
DS
TB P
WM
OU
TFL
AS
H T
RG
STB
CH
G L
V
D G
ND
D G
ND
D G
ND
INT
STB
ON
LD
GN
DD
GN
DD
GN
DU
NR
EG
UN
RE
GU
NR
EG
GN
DG
ND
GN
DG
ND
GN
DG
ND
LCD
CS
LCD
SD
OU
TLC
D S
CK
LCD
HD
LCD
VD
LCD
CLK
LCD
OU
T0
LCD
OU
T1
LCD
OU
T2
LCD
OU
T3
LCD
OU
T4
LCD
OU
T5
LCD
OU
T6
LCD
OU
T7
LCD
OU
T8
LCD
OU
T9
LCD
OU
T10
LCD
OU
T11
LCD
OU
T12
LCD
OU
T13
LCD
OU
T14
LCD
OU
T15
D2R
5VD
3VB
L+B
L -
P90
02B
AT+
ID B
AT D
QT
HE
RM
OB
AT-
1 2 3 4
BATTERY
ECM(L) ECM(R)
ECM FLEX UNIT
LCD BACKLIGHT UNIT
S-5
6 1
3
2
4
5
QR8001B1GKCFJN0008
CL8004
CL8001
CL8009
CL8010
CL8007
CL8008
CL8006
CL8005
CL8003
D8001B0ECGP000005
B0HCMP000006D8002
DA2JF8100LD8003
100K[36]R8013
1M[D][22]R8005
R80061M[D][22]
R800715K[D]
R800915K
R80081K
22[18]R8003
100[18]R8004
R8001
510K[22]
$R8011
R8010
68
R8015
1500
R8014510K[22]
100K[18]R8002
F1K2J102A028C8003
[36]
630V
F1K2J223A029C8007
630V
$C8014
F1J1A106A043C8006
[22]
10V
F1K2J223A029C8001
630V
1u[18]
C8015
F1H0J1050012
6.3V
ConfidentialUntil
ERBSE1R50UF8001
1
2
G1
G2
P8003
K1KA02B00292
1
2
G1
G2
K1KA02BA0022
P8004
F9Z000000038
300V265uF
C8002
6
7
5
9
10
8
1
3
4
2
13
15
14
11
12
20
18
19
16
17
K1KA20BA0052
PP8001
3 2 1
4 5 6
B1DFCG000018
Q8004
B1GBCFGJ0021QR8002
QR8003
*
21
34
T8001G5D1A0000059
3 41 2
8 7 56
B1JBLP000017Q8003
CG
G
D
SE
[FPSN4TP]
[RJP4003ANS]
[K]
LAMP+
LAMP-
TRG_IN
UNREG_GND
UNREG_GND
UNREG_GND
UNREG_GND
PW_5V
STB_PWM_OUT
STROBE_TRG
STB_CHG_LV
D_GND
D_GND
D_GND
D_GND
D_GND
D_GND
INT_STB_ON_L
FRAME_GND
FRAME_GND
FRAME_GND
UNREG
UNREG
UNREG
or
or
VariationCategory
QR8003
FZ100 FZ45
B1GBCFJJ0064 $[B1GBCFJJ0064]
CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,REPLACE ONLY WITH THE SAME TYPE 1.5A 32V FUSE.
ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUESD' INCENDIE N' UTILISERQUE DES FUSIBLE DE MÉME TYPE 1.5A 32V.1.5A 32V
1.5A 32V
DMC-FZ100FlashSchematic Diagram
10987654321
G
F
E
D
C
B
A
S4.2. Flash Schematic Diagram
S-6
ConfidentialUntil
1
5
6
3
2
4
K1MY06BA0370FP9301
1
43
2
D9301B3ADB0000135
1
8
6
4
2
3
5
7
9
11
12
10
K1MY12BA0370FP9302
C9301F1G1H470A565
50V
13
56
42
K2HD104D0002
JK9301
LB9302J0JCC0000415
LB9301J0JCC0000415
LB9303J0JCC0000415
LB9304J0JCC0000415
RL9301
D4ED18R00008VA9301
D_GND
D_GND
D_GND
D_GND
AF_ON
AF_ON
AFMF_A
AFMF_A
AFMF_B
AFMF_B
MIC_R
MIC_L
REMOTE
AF_LED_K
AF_LED_A(SML-J14DTT96)
MIC_GND
MIC_GND
MIC_GND
DMC-FZ100Mic JackSchematic Diagram
10987654321
G
F
E
D
C
B
A
S4.3. Mic Jack Schematic Diagram
S-7
2 3
1 4
K0L1CB000003
S9401
1
6
4
2
3
5
FT9401
ConfidentialUntil
2 4
1 3
K0F111A00541S9402
VA9401
$[D4ED18R00008]
VA9402
$[D4ED18R00008]
VA9403
$[D4ED18R00008]
D_GND
D_GND
D_GND
AF/MF
AFMF_B
AFMF_A
MFAF
FOCUS
AF_ON
TO MIC_JACK
(TO K1MY06BA0152) K1MY06BA0370
DMC-FZ100AF MF FlexSchematic Diagram
ConfidentialUntil
RL4302
RL4301
K0L1BA000147
SW4301
D_GND
LCD_TAIMEN
(SPVS410100(ALPS))
D_GND
LCD_TAIMEN
DMC-FZ100HingeSchematic Diagram
10987654321
G
F
E
D
C
B
A
S4.4. AF MF Flex Schematic Diagram / S4.5. Hinge Schematic Diagram
S-8
A
B
C
D
E
F
G
654321
5
6
7
8
13
14
15
24
25
28
29
26
27
21
22
36
37
38
39
4
3
2
1
PHOTOSENSOR ZOOM ENCODER 1
DC SOLENOID(IRIS)
B
10
11
9
12
16
17
18
19
20
23
30
31
32
33
34
35
DC SOLENOID(SHUTTER)
SHUTTER UNITH
POSITIVE VOLTAGE LINE
DMC-FZ100 LENS FLEX SCHEMATIC DIAGRAM
TO MAIN(MAIN CN) CIRCUIT(FP9005)
STEPPINGMOTOR FOCUS MOTOR UNITF
40
COIL
COIL
DC MOTOR ZOOM MOTOR UNITC
PHOTOSENSOR ZOOM ENCODER 2A
G3
G4
G5
G2
F1
F3
F4
H1
H3
ABS(ZENC2)
LED CONT(Z1 LED)
ABS(ZENC1)
ENC VCC(D2R9V)
LED CONT(Z2 LED)
ENC VCC(D2R9V)
ZM2(DCM-)
ZM2(DCM-)
ZM1(DCM+)
ZM1(DCM+)
ENC VCC(D2R9V)
ABS(FHP)
LED CONT(FHP LED)
ENC VCC(D2R9V)
ABS(ZHP)
LED CONT(ZHP LED)
FAN(FMAN)
FBN(FMBN)
FAP(FMAP)
FBP(FMBP)
Y DRV+(Y DR+)
Y HI-(YVH-)
Y HO+(YVO+)
Y HI+(YVH+)
Y HO-(YVO-)
Y DRV-(Y DR-)
ST3(IRIS BP)
ST1(IRIS AP)
ST4(IRIS BN)
ST2(IRIS AN)
SH-(SHUT OUT1)
SH-(SHUT OUT1)
SH+(SHUT OUT2)
SH+(SHUT OUT2)
X DRV-(X DR-)
X DRV+(X DR+)
X HI-(XVH-)
X HO+(XVO+)
X HI+(XVH+)
X HO-(XVO-)
A1
B1
B3
B2
A3
A2
C2
C1
D1
D2
D3
E1
E2
E3
F2
G6
G1
H2
H4
H6
H5
G8
G7
G10
G11
G12
G9
PHOTOSENSOR FOCUS PHOTO UNITD
PHOTOSENSOR ZOOM PHOTO UNITE
HALL SENSOR (X)
HALL SENSOR (Y)
DRIVE COIL (X)
DRIVE COIL (Y)
OIS UNITG
OIS UNITG
S4.6. Lens Flex Schematic Diagram
S-9
CL8001
CL8003
CL8004
CL8005
CL8006
CL8007CL8008
CL8009
CL8010
C8003
C8006
C8014
C8015
D8002
D8003
F8001
20
15
11
10
51
PP8001
2
1 P8003
1 2
P8004
65
4 32
1
QR8001
e
QR8002
e
QR8003
6 5 4
321
Q8004
R8005 R8006
R8007
R8008
R8009
R8010
R8011
R8015
4
3 2
1
T8001
16
5
FP9301
110 512 FP9302
C8001
C8007 D
8001
87654
32
1
Q8003
R8001
R8002
R8003
R8004
R8013
R8014
C8002
4 3
2 1D9301
RL9301
LB9304C9301
VA9301
LB9301
LB9302
LB9303
65
43
21
JK9301
DMC-FZ100Mic Jack P.C.B.
DMC-FZ100Flash P.C.B.
10987654321
G
F
E
D
C
B
A
(Foil Side)
(Foil Side)
(Component Side) (Component Side)
S5. Print Circuit BoardS5.1. Flash P.C.B. / S5.2. Mic Jack P.C.B.
S-10
4 321
S9401
4
3
2
1
S9402
VA9401
VA9402
VA9403
FT9401
12
SW4301
(Foil Side)
RL4301
RL4302
DMC-FZ100Hinge P.C.B.
DMC-FZ100AF MF Flex P.C.B.
10987654321
G
F
E
D
C
B
A
(Foil Side)
(Component Side)
S5.3. AF MF Flex P.C.B. / S5.4. Hinge P.C.B.
S-11
S5.5. Lens Flex P.C.B.
1 2 3 4 5 6
A
B
C
D
E
DMC-FZ100 LENS FLEX P.C.B.
ZOOM MOTOR UNIT
C1
C
A ZOOM ENCODER 2
B ZOOM ENCODER 1
Pin 40
Pin 1
FOCUS MOTOR UNIT
D3
F
D2
D1
F4
SHUTTER UNITH
OIS UNITG
C2
B3B1B2
FOCUS PHOTO UNIT D
E1
E2
E3
ZOOM PHOTO UNIT E
F1
F3F2
A3A1
A2
G6G1
G12G7
H6H1
S-12
S6. Replacement Parts List
S-13
Note: 1. * Be sure to make your orders of replacement parts according to this list.2. IMPORTANT SAFETY NOTICE
Components identified with the mark have the special characteristics for safety. When replacing any of these components, use only the same type.
3. Unless otherwise specified,All resistors are in OHMS, K=1,000 OHMS. All capacitors are in MICRO-FARADS (uf), P=uuF.
4. The marking (RTL) indicates the retention time is limited for this item. After the discontinuation of this assembly in production, it will no longer be available.
5. Supply of CD-ROM, in accordance with license protection, is allowable as replacement parts only for customers who accidentally damaged or lost their own.
E.S.D. standards for Electrostatically Sensitive Devices, refer to PREVENTION OF ELECTROSTATIC DISCHARGE (ESD) TO ELECTROSTATICALLY SENSITIVE (ES) DEVICESsection.Definition of Parts supplier:
1. Parts marked with [ENERGY] in the remarks column are supplied from PanasonicCorporation Energy Company.
2. Parts marked with [PAVCSG] in the remarks column are supplied from PAVCSG.Others are supplied from AVC-CSC-SPC.
DMC-FZ100EGK
Ref.No. Part No. Part Name & Description Pcs Remarks Ref.No. Part No. Part Name & Description Pcs Remarks ## VEP56108B MAIN P.C.B. 1 EG,EP,EF,EB (RTL) E.S.D. ## VEP59082A AF MF FLEX U (RTL)[PAVCSG] ## VEP56108A MAIN P.C.B. 1 EE,P,PC,PU,GC,SG,GT,GK,
GN,GD (RTL) E.S.D. S9401 K0L1CB000003 SWITCH 1 [PAVCSG] ## VEP58119A FLASH P.C.B. 1 (RTL) E.S.D. S9402 K0F111A00591 SWITCH 1 [PAVCSG] ## VEP59081A AF LED P.C.B. 1 (RTL) E.S.D. ## VEP59082A AF MF FLEX UNIT 1 (RTL)[PAVCSG] ## VEP58118A HINGE P.C.B. 1 (RTL)[PAVCSG] ## VEP58118A HINGE P.C.B. (RTL)[PAVCSG]
SW4301 K0L1BA000147 SWITCH 1 [PAVCSG]
## VEP58119A FLASH P.C.B. (RTL) E.S.D. C8001 F1K2J223A029 C.CAPACITOR 630V 0.022U 1C8002 F9Z000000038 E.CAPACITOR 1C8003 F1K2J102A028 C.CAPACITOR 630V 1000P 1C8006 F1J1A106A043 C.CAPACITOR CH 10V 10U 1C8007 F1K2J223A029 C.CAPACITOR 630V 0.022U 1C8015 F1H0J1050012 C.CAPACITOR CH 6.3V 1U 1 D8001 B0ECGP000005 DIODE 1 E.S.D.D8002 B0HCMP000006 DIODE 1 E.S.D.D8003 DA2JF8100L DIODE 1 E.S.D. F8001 ERBSE1R50U FUSE 32V 1.5A 1 P8003 K1KA02B00292 CONNECTOR 2P 1P8004 K1KA02BA0022 CONNECTOR 2P 1 PP8001 K1KA20BA0052 CONNECTOR 20P 1 Q8003 B1JBLP000017 TRANSISTOR 1 E.S.D.Q8004 B1DFCG000018 TRANSISTOR 1 E.S.D. QR8001 B1GKCFJN0008 TRANSISTOR-RESISTOR 1 E.S.D.QR8002 B1GBCFGJ0021 TRANSISTOR-RESISTOR 1 E.S.D.QR8003 B1GBCFJJ0064 TRANSISTOR-RESISTOR 1 E.S.D. R8001 ERJ6GEYJ514V M.RESISTOR CH 1/10W 514K 1R8002 ERJ3GEYJ104 M.RESISTOR CH 1/10W 100K 1R8003 ERJ3GEYJ220 M.RESISTOR CH 1/10W 22 1R8004 ERJ3GEYJ101 M.RESISTOR CH 1/10W 100 1R8005 ERJ6RED105 M.RESISTOR CH 1/10W 1M 1R8006 ERJ6RED105 M.RESISTOR CH 1/10W 1M 1R8007 ERJ2RHD153X M.RESISTOR CH 1/16W 15K 1R8008 ERJ2GEJ102X M.RESISTOR CH 1/16W 1K 1R8009 ERJ2GEJ153 M.RESISTOR CH 1/16W 15K 1R8010 ERJ2GEJ680 M.RESISTOR CH 1/10W 68 1R8013 ERJ8GEYJ104V M.RESISTOR CH 1/8W 100K 1R8014 ERJ6GEYJ514V M.RESISTOR CH 1/10W 514K 1R8015 ERJ2GEJ152 M.RESISTOR CH 1/16W 1.5K 1 T8001 G5D1A0000059 SWITCHING TRANSFORMER 1 ## VEP59081A AF LED P.C.B. (RTL) E.S.D. C9301 F1G1H470A565 C.CAPACITOR CH 50V 47P 1 D9301 B3ADB0000135 DIODE 1 E.S.D.
FP9301 K1MY06BA0370 CONNECTOR 6P 1FP9302 K1MY12BA0370 CONNECTOR 12P 1 JK9301 K2HD104D0002 JACK 1 LB9301 J0JCC0000415 FILTER 1LB9302 J0JCC0000415 FILTER 1LB9303 J0JCC0000415 FILTER 1LB9304 J0JCC0000415 FILTER 1 VA9301 D4ED18R00008 VARISTOR 1
S-14
DMC-FZ100EGK
Ref.No. Part No. Part Name & Description Pcs Remarks Ref.No. Part No. Part Name & Description Pcs Remarks1 VDW2044 LENS RING FRONT 1 [PAVCSG] 100 VXW1144 LENS UNIT (W/O MOS) 12 VEP59082A AF MF FLEX UNIT 1 (RTL)[PAVCSG] 101 VXP3444 1ST LENS FRAME UNIT 13 VGQ0A13 AF LIGHT CASE 1 [PAVCSG] 102 VXP3336 2ND LENS FRAME UNIT 14 VGQ0M33 AF/MF OP SUPPORT 1 [PAVCSG] 103 VXQ1969 MIDDLE FRAME UNIT 15 VXQ1695 AF/MF OP SLIDE KNOB 1 [PAVCSG] 104 L6HA68ND0001 FOCUS MOTOR UNIT 16 VGU0G16 AF/MF OP BUTTON 1 [PAVCSG] 105 VXP3337 3RD LENS FRAME UNIT 17 VYK4B86 FRONT CASE UNIT 1 [PAVCSG] 106 VXP3343 4TH LENS FRAME UNIT 17-1 VGQ0M31 GRIP PIECE FRONT 1 [PAVCSG] 107 VDW1953 CAM FRAME UNIT 18 VYK4H89 AF/MF OP CASE UNIT 1 [PAVCSG] 108 VMC2134 WAVE WASHER 19 VYK4H90 AF/MF OP SPRING UNIT 1 [PAVCSG] 109 VXQ1993 MASTER FLANGE UNIT 110 L0AA01A00053 SPEAKER 1 [PAVCSG] 110 VML4007 CAM STOPPER 111 VGQ0N41 HINGE PLATE SHEET 1 [PAVCSG] 111 VMA0X37 MASTER FLANGE PLATE 112 VGQ0P47 WIRE FIX TAPE 1 [PAVCSG] 112 L6DAADHD0001 ZOOM MOTOR UNIT 113 VGQ0P47 WIRE FIX TAPE 1 [PAVCSG] 113 VEK0Q46 LENS FLEX UNIT 114 VKM8424 HINGE ARM COVER TOP 1 [PAVCSG] 113-1 B3NBA0000015 PHOTO COUPLER 115 VKM8425 HINGE ARM COVER BOTTOM 1 [PAVCSG] 113-2 B3NBA0000011 PHOTO SENSOR 116 VMP9638 HINGE EARTH PLATE 1 [PAVCSG] 113-3 K1MN18BA0209 CONNECTOR 18P 117 VMP9665 SPEAKER FIX PLATE 1 [PAVCSG] 114 VMB4205 FLAP SPRING 118 VMP9668 HINGE PLATE 1 [PAVCSG] 115 VMB4205 FLAP SPRING 119 VYK4D76 LCD HINGE UNIT 1 [PAVCSG] 116 VEK0R01 MOS SENSOR FLEX U 120 VEE1F12 HINGE SW HARNESS 1 [PAVCSG]21 VEP58118A HINGE P.C.B. 1 (RTL)[PAVCSG] B4 XQN16+BJ4FN SCREW 1 [PAVCSG]22 VYK4H88 REAR CASE UNIT 1 [PAVCSG] B5 VHD1870-A SCREW 1 [PAVCSG]22-1 VGQ0M35 LCD LOCK PIECE 1 [PAVCSG] B6 VHD1870-A SCREW 1 [PAVCSG]22-2 VGU0G07 PLAY BUTTON 1 [PAVCSG] B7 VHD1870-A SCREW 1 [PAVCSG]22-3 VGU0G08 CURSOR BUTTON 1 [PAVCSG] B8 VHD2198 SCREW 1 [PAVCSG]22-4 VMB4373 LCD LOCK SPRING 1 [PAVCSG] B9 VHD2247 SCREW 1 [PAVCSG]22-5 VMS7523 STRAP HOLDER (L) 1 [PAVCSG] B10 VHD2247 SCREW 1 [PAVCSG]23 EFN-AMBM7ZD FLASH 1 [PAVCSG] B11 VHD1870-A SCREW 1 [PAVCSG]24 VEP54016A ECM FLEX UNIT 1 [PAVCSG] B12 VHD1870-A SCREW 1 [PAVCSG]25 VKM8616 FLASH CASE BOTTOM 1 [PAVCSG] B13 VHD1870-A SCREW 1 [PAVCSG]26 VMB4377 FLASH POP UP SPRING 1 [PAVCSG] B14 VHD2150-A SCREW 1 [PAVCSG]27 VMP9666 FLASH EARTH PLATE 1 [PAVCSG] B15 VHD2150-A SCREW 1 [PAVCSG]28 VMS7911 FLASH SHAFT 1 [PAVCSG] B16 VHD2150-A SCREW 1 [PAVCSG]29 VMT1962 MIC DAMPER 1 [PAVCSG] B18 VHD2251-A SCREW 1 [PAVCSG]30 VMT2011 MIC CUSHION 1 [PAVCSG] B19 VHD2179 SCREW 131 VYK4B78 FLASH CASE TOP 1 [PAVCSG] B20 VHD2179 SCREW 132 VYK4B79 FLASH CASE UNIT 1 [PAVCSG] B21 VHD2179 SCREW 133 VYK4E04 HOT SHOE UNIT 1 [PAVCSG] B22 VHD2179 SCREW 134 VYQ3749 FLASH SW UNIT 1 [PAVCSG] B23 VHD2179 SCREW 150 VMC2111 SHOE SPRING 1 B24 VHD1870-A SCREW 1 [PAVCSG]51 VSC6223 LENS HEAT SINK 1 B25 VHD1870-A SCREW 1 [PAVCSG]52 VMP9671 SIDE FRAME (R) 1 B26 VHD1870-A SCREW 1 [PAVCSG]53 VMS7523 STRAP HOLDER (R) 1 B27 VHD2252-A SCREW 1 [PAVCSG]54 VGQ0M29 REMOTE HOLDER 1 B28 VHD2252-A SCREW 1 [PAVCSG]55 VKF4715 REMOTE COVER 1 B29 VHD2252-A SCREW 1 [PAVCSG]56 VKF4714 JACK COVER 1 B50 VHD2179 SCREW 157 VWJ2181 MIC JACK FLEX 1 B51 VHD2179 SCREW 158 VEP59081A AF LED P.C.B. 1 (RTL) E.S.D. B52 VHD2179 SCREW 160 VMC2128 BATTERY EARTH PLATE (TOP) 1 B53 VHD2179 SCREW 161 VGQ0M36 CONDENSOR COVER 1 B57 VHD2251 SCREW 162 VYK4B82 BATTERY CASE UNIT 1 B59 XTV2+8JFN SCREW 162-1 VGQ0M26 COUPLER COVER 1 B60 XTV2+8JFN SCREW 162-2 VGU0G10 BATTERY DOOR LOCK KNOB 1 B61 XTV2+8JFN SCREW 162-3 VGU0G12 BATTERY LOCK KNOB 1 B62 XTV2+8JFN SCREW 162-4 VKF4713 BATTERY DOOR 1 B63 XQN16+BJ5FN SCREW 162-5 VMB4199 BATTERY LOCK SPRING 1 B64 XQN16+BJ5FN SCREW 162-6 VMB4385 BATTERY SPRING 1 B65 XQN16+BJ4FN SCREW 162-7 VMB4406 BATTERY DOOR SPRING 1 B66 VHD2062 SCREW 162-8 VMP9670 BATTERY DOOR PLATE 1 B67 VHD2062 SCREW 162-9 VMS7525 BATTERY DOOR HINGE SHAFT 1 B68 XQN16+BJ4FN SCREW 162-10 VQL2G54 BATTERY DOOR LABEL 1 B69 XQN16+BJ4FN SCREW 163 VEP58119A FLASH P.C.B. 1 (RTL) E.S.D. B70 XQN16+BJ4FN SCREW 164 VGQ0M27 JACK HOLDER 1 B101 XQN16+CJ5FN SCREW 165 L5EDDXE00008 EVF UNIT 1 B102 XQN16+CJ5FN SCREW 166 VKM8617 LCD CASE TOP 1 B103 XQN14+C3FN SCREW 167 VKM8618 LCD CASE BOTTOM 1 B104 XQN14+B35FN SCREW 168 VYK4E07 LCD BACK LIGHT UNIT 1 B105 XQN16+C5FN SCREW 169 K0RB02500001 TOP OPERATION UNIT 1 B106 XQN16+C5FN SCREW 170 VEP56108B MAIN P.C.B. 1 EG,EP,EF,EB (RTL) E.S.D. B107 XQN16+CJ5FN SCREW 170 VEP56108A MAIN P.C.B. 1 EE,P,PC,PU,GC,SG,GT,GK, B108 XQN16+CJ5FN SCREW 1
GN,GD (RTL) E.S.D. B109 XQN16+CJ5FN SCREW 170-1 ML-614S/ZTK BATTERY 1 [ENERGY](B9101) B110 VHD2258 SCREW 170-2 VGQ0Q80 THERMAL SHEET 1 B111 VHD2258 SCREW 170-3 VGQ0Q81 MAIN COPPER FOIL SHEET 1 B112 VHD2242 SCREW 171 VGQ0P49 INSULATION SHEET 1 B113 VHD2242 SCREW 172 VGQ0P49 INSULATION SHEET 1 B114 VHD2242 SCREW 1
S-15
DMC-FZ100EGK
Ref.No. Part No. Part Name & Description Pcs Remarks Ref.No. Part No. Part Name & Description Pcs Remarks 311 VQT2U50 SIMPLIFIED O/I 1 EE 200 ----- BATTERY 1 P,PC,PU (RUSSIAN/UKRAINIAN)201 DE-A83BA BATTERY CHARGER 1 P,PC,PU 311 VQT2U51 SIMPLIFIED O/I 1 GC,SG 202 K1HA14AD0003 USB CABLE W/PLUG 1 P,PC,PU (ENGLISH/203 K1HA14CD0004 AV CABLE W/PLUG 1 P,PC,PU CHINESE(TRADITIONAL))204 VFF0636-S CD-ROM 1 P,PC,PU See "Notes" 311 VQT2U52 SIMPLIFIED O/I 1 GC 205 VYQ5607 LENS CAP UNIT 1 P,PC,PU (ARABIC/PERSIAN)206 VYQ5606 LENS HOOD UNIT 1 P,PC,PU 311 VQT2U53 SIMPLIFIED O/I 1 GT 207 VPF1166 CAMERA BAG 1 P,PC,PU (CHINESE(TRADITIONAL))208 VPK4504 PACKING CASE 1 P,PC 311 VQT2U54 SIMPLIFIED O/I 1 GK 208 VYQ5874 PACKING CASE 1 PU (CHINESE(SIMPLIFIED))209 VPN7068 PAD 1 P,PC,PU 311 VQT2U55 SIMPLIFIED O/I 1 GN 210 VFF0639 CD-ROM 1 P,PC,PU (ENGLISH)
(INSTRUCTION BOOK) 311 VQT2U56 INSTRUCTION BOOK 1 GD 211 VQT2U38 INSTRUCTION BOOK 1 P (KOREAN)
(ENGLISH/SPANISH) 312 VQC7743 O/I SOFTWARE 1 EG 211 VQT2U39 SIMPLIFIED O/I 1 PC (GERMAN/FRENCH/ITALIAN/
(ENGLISH/CANADIAN FRENCH) DUTCH/SPANISH/PORTUGUESE/211 VQT2U40 SIMPLIFIED O/I 1 PU TURKISH)
(SPANISH/PORTUGUESE) 312 VQC7744 O/I SOFTWARE 1 EP 212 VQC7741 O/I SOFTWARE 1 P,PC (FINNISH/SWEDISH/DANISH/
(ENGLISH/CANADIAN FRENCH) POLISH/CZECH/HUNGARIAN)212 VQC7742 O/I SOFTWARE 1 PU 312 VQC7745 O/I SOFTWARE 1 EF
(SPANISH/PORTUGUESE) (FRENCH)213 VPF1230 BAG, POLYETHYLENE 1 P,PC,PU 312 VQC7746 O/I SOFTWARE 1 EB,GN 214 VFC4453 SHOULDER STRAP 1 P,PC,PU (ENGLISH) 312 VQC7747 O/I SOFTWARE 1 EE (RUSSIAN/UKRAINIAN)
312 VQC7748 O/I SOFTWARE 1 GC,SG (ENGLISH/
300 ----- BATTERY 1 EG,EP,EF,EB,EE,GC,SG,GT, CHINESE(TRADITIONAL)/ GN,GD,GK ARABIC/PERSIAN)
301 DE-A84AA BATTERY CHARGER 1 EG,EP,EF,EB,EE,GN 312 VQC7749 O/I SOFTWARE 1 GT 301 DE-A84BA BATTERY CHARGER 1 GC,GK,GD (CHINESE(TRADITIONAL)301 DE-A84DA BATTERY CHARGER 1 SG 312 VQC7750 O/I SOFTWARE 1 GK 301 DE-A84CA BATTERY CHARGER 1 GT (CHINESE(SIMPLIFIED))302 K1HA14AD0003 USB CABLE W/PLUG 1 EXCEPT P,PC,PU 312 VQC7751 O/I SOFTWARE 1 GD 303 K1HA14CD0004 AV CABLE W/PLUG 1 EXCEPT P,PC,PU (KOREAN)304 VFF0637-S CD-ROM 1 GK See "Notes" 313 VPF1230 BAG, POLYETHYLENE 1 EXCEPT P,PC,PU 304 VFF0636-S CD-ROM 1 EG,EP,EF,EB,EE,GC,SG,GT, 314 VFC4453 SHOULDER STRAP 1 EXCEPT P,PC,PU
GN,GD See "Notes" 316 VQL1S66 LABEL 1 EB,GK 305 VYQ5607 LENS CAP UNIT 1 EXCEPT P,PC,PU 317 VQL2C68-1 TAI WAN OPERATING LABEL 1 GT 306 VYQ5606 LENS HOOD UNIT 1 EXCEPT P,PC,PU 339 K2CT39A00002 AC CORD W/PLUG 1 EB,GC 307 VPF1166 CAMERA BAG 1 EXCEPT P,PC,PU 340 K2CQ29A00002 AC CORD W/PLUG 1 EG,EP,EF,EE,GC 308 VPK4505 PACKING CASE 1 EG,EP,EF,EB,EE,GC,SG,GN 340 K2CR29A00001 AC CORD W/PLUG 1 GD 308 VYQ5875 PACKING CASE 1 GK 341 K2CJ29A00002 AC CORD W/PLUG 1 GN 308 VYQ5874 PACKING CASE 1 GT,GD 342 K2CA29A00023 AC CORD W/PLUG 1 SG 309 VPN7068 PAD 1 EXCEPT P,PC,PU 342 K2CA29A00021 AC CORD W/PLUG 1 GT 310 VFF0640 CD-ROM 1 EG,EP,EF,EB 342 K2CA2YY00070 AC CORD W/PLUG 1 GK
(INSTRUCTION BOOK)310 VFF0641 CD-ROM 1 EE,SG
(INSTRUCTION BOOK)310 VFF0642 CD-ROM 1 GC,GN
(INSTRUCTION BOOK)310 VFF0643 CD-ROM 1 GT,GD
(INSTRUCTION BOOK)310 VFF0644 CD-ROM 1 GK
(INSTRUCTION BOOK)311 VQT2U41 SIMPLIFIED O/I 1 EG
(GERMAN/FRENCH)311 VQT2U42 SIMPLIFIED O/I 1 EG
(ITALIAN/DUTCH)311 VQT2U43 SIMPLIFIED O/I 1 EG
(SPANISH/PORTUGUESE)311 VQT2U44 SIMPLIFIED O/I 1 EG
(TURKISH)311 VQT2U45 SIMPLIFIED O/I 1 EP
(SWEDISH/DANISH)311 VQT2U46 SIMPLIFIED O/I 1 EP
(POLISH/CZECH)311 VQT2U47 SIMPLIFIED O/I 1 EP
(HUNGARIAN/FINNISH)311 VQT2U48 SIMPLIFIED O/I 1 EF
(FRENCH)311 VQT2U49 INSTRUCTION BOOK 1 EB
(ENGLISH)
S-16
S7. Exploded ViewS7.1. Frame and Casing Section
S-17
66
68
67B52
B53
B50
B51
B59
B60
71 72 51
14
15B9
B1019
B821
16
B1920
B20B5
22
22-122-4
(Not supplied)
22-5
22-2
22-3
B13
B61
B769
17
101213
11B25
B2618
64
70
B68 B69
B70
B57
(Not supplied)
62
62-1
62-5
62-6
62-9
62-7
62-462-2
62-8
62-10
B6563
61
60(C8002)
31
29
24
30
2326
27
25
B11B12
B22B15B21
B14
B16
B18
65
B62
2834
32
B64
53
56
555458
B6357
3
B4 B28B29
B27
59
8
62
B23
B6
4
7
7-1
1
62-3
B24
52
3350
70-1
B66
B67
70-2
70-3
S-18
S7.2. Camera Lens Section
101102
103
104 105106
107
108
109 110
111
112
113 114
115 116
B101 B102
B103
B104
B105
B106
B107
B108
B109
B110B111
B112B113B114
100
113-1113-2
113-3
S-19
S7.3. Packing Parts and Accessories Section (1)
203
202
209
207
213
200
214
205
206
211
201
208
204
212
(Not supplied)
210
S-20
S7.4. Packing Parts and Accessories Section (2)
303
302309
307
313
300
314
305
306
311
301
308
304
312
(Not supplied)
310
317
(DMC-FZ100EE/EF/EG/EP/GC/GD)
(DMC-FZ100EB/GC)
(DMC-FZ100GN)
(DMC-FZ100GK/GT/SG)
342
340
341
339
316