panaray mb4 modular bass loudspeaker - avguy.com · power stereo bank 802 full range input...
TRANSCRIPT
PANARAY®
MB4 Modular BassLoudspeaker
General Description
Technical Information
1Band-limited pink noise is applied to the MB4 speaker and amplified to a level at the loudspeakerterminals corresponding to 1 Watt as referenced to the nominal impedance. The average soundpressure level (dB-SPL) is measured at 1 meter from the speaker in an anechoic environment.2Band-limited pink noise is applied to the MB4 speaker and amplified to a level at the loudspeakerterminals corresponding to the long-term rated power handling of the speaker. The average soundpressure level (dB-SPL) is measured at 1 meter from the speaker in an anechoic environment.3Band-limited noise, meeting the IEC Standard #268-5 is applied to the MB4 speaker and amplifiedto a level at the loudspeaker terminals corresponding to the power handling of the loudspeaker. Theloudspeaker must show no visible damage or measurable loss of performance after 100 hours ofcontinuous testing.
Enclosure construction: High-densityMultiFiber multi-layer wood particlepanel with high-impact foamedpolypropylene end caps.
The PANARAY MB4 modular bassloudspeaker is a 200W, low-fre-quency loudspeaker that can beused for indoor permanent installa-tions and for portable applications.Multiple MB4 speakers can becombined to effectively create alarger single bass enclosure resultingin higher SPL.
The MB4 speaker’s output, band-width and size make it useful as asingle bass unit, or as a modularbuilding block to match other Bose®
products in most professionalsystems.
The MB4 speaker can also be usedin conjunction with the MB4 endfireor broadside bass array brackets andthe PANARAY system digital control-ler to create directional bass.
The PANARAY MB4 modular bassloudspeaker offers the followingfeatures:
• Wide frequency range, from 40Hzto 300Hz, which can be easilymatched to any Bose professionalloudspeaker
• High impact output for dominantbass material
• Rugged portable enclosure withmetal grille and carrying handles
• Distinctive styling
• Recessed back plate with twoSpeakon® NL4 connectors
• Full complement of brackets tosimplify installations
The MB4 speaker can be used withthe Bose PANARAY system digitalcontroller to provide smooth accu-rate spectral response over the entireoperating range of the system.
The MB4 speaker can also be usedwith the Bose 1600 or 1800 amplifi-ers in combination with the MB4plug-in EQ card to provide activeequalization for the system.
Frequency Range40Hz to 300Hz ±3dB
Sensitivity1
87dB-SPL @ 1W, 1m (pink noise)
Maximum Acoustic Output2
110dB-SPL, @ 1m (pink noise)
Dispersion
Omnidirectional at all frequenciesbelow 200Hz
Long-Term Power Handling3
200W continuous
Impedance8Ω nominal
Mechanical SpecificationsDimensions:
18.1"D x 10.2"W x 26.7"H
(46 cm x 25.9 cm x 67.8 cm)Weight: 45 lb (20 kg)
Connectors: Two (2) parallel-wiredNL4 connectorsAvailable colors: White and Black
A single MB4 speaker is wellmatched in output and bandwidth toone or two PANARAY 402-II, 502A orMA12 loudspeakers, providing a full-range solution for distributed orportable systems.Two or three MB4 speakers are agood match for higher-outputloudspeakers, like the PANARAY802®-III speaker, for engineered orportable systems.
For larger spaces that require evenhigher SPL, four or more MB4speakers can be combined with eachPANARAY LT series loudspeaker.
1 110
2 1163 1194 122
Incremental bass output can beachieved by combining multiple MB4units in close proximity.# of Panaray MB4s Max Output (dB)
PANARAY MB4 LoudspeakerSizing
POWER
Stereo Bank802 Full Range
INPUT METERS
-dB
L
R
40 24 18 12 6 0 O
PANARAY DIGITAL SYSTEM CONTROLLER
PRESET LIMIT
UTILITY DELA
CHANNEL 2 GAIN
0
1
2
34 5 6
7
8
9
10 0
1
2
34 5 6
7
8
9
10
CLIPPING LEVEL
–1 dB
–3 dB
–12 dB
–40 dB
ON
CHANNEL 1 CHANNEL 2
1800–IV PROFESSIONAL POWER AMPLIFIER
I CHANNEL 2 GAIN
0
1
2
34 5 6
7
8
9
10 0
1
2
34 5 6
7
8
9
10
CLIPPING LEVEL
–1 dB
–3 dB
–12 dB
–40 dB
ON
CHANNEL 1 CHANNEL 2
1800–IV PROFESSIONAL POWER AMPLIFIER
I
Engineers’ and Architects’Specifications
Warranty Information
All versions of the Bose PANARAYMB4 modular bass loudspeakers arecovered by a 5-year, transferablelimited warranty.
Safety and RegulatoryCompliance
All versions of the PANARAY MB4modular bass loudspeakers complywith ANSI/EIA 636, RecommendedLoudspeaker Safety Practices andEMC Directive 89/336/EEC andArticle 10 (1) of the Directive incompliance with EN50081-1, EN50082-1, as signified by the CEmark.
The loudspeaker shall be a multipledriver, low-frequency system withmatched active equalization asfollows:
The transducer complement shallconsist of four low-frequency driversof 5.2" (13.3 cm) diameter, mountedsymmetrically in vertical pairs. Eachdriver shall have rated impedance of8Ω and shall be wired in series/parallel, resulting in compositenominal impedance of 8Ω.
The loudspeaker system sensitivityshall be 87dB-SPL in the 40Hz to300Hz frequency range with mea-surements referenced to 1W (2.85V)pink noise input at 1m. The disper-sion shall be omnidirectional at allfrequencies below 200Hz. The powerhandling capacity of the loudspeakershall be 200W continuous pink noise,band-limited from 40Hz to 300Hz.
The loudspeaker shall be a ventedenclosure, tuned at 45Hz. The inputconnectors of the PANARAY MB4speaker shall consist of two parallelSpeakon® NL4 receptacles.
The enclosure of the MB4 loud-speaker shall be composed ofhigh-density MultiFiber multi-layerwood particle panel with high-impactfoamed polypropylene end caps. Itsouter dimensions shall be 18.1"D x10.2"W x 26.7"H (45 cm x 25.9 cm x67.8 cm). Its weight shall be 45 lb (20kg).
Full-Range System with PANARAY® System Digital ControllerFull-Range System with Bose® Amplifers
The loudspeaker shall be thePANARAY MB4 modular bass loud-speaker.
The loudspeaker system shall beused with a separate system control-ler, to be connected to the input(s) ofthe system power amplifier(s), or withan MB4 EQ card, to be installed in aBose 1600 or 1800 amplifier.
The PANARAY system digital control-ler shall provide active electronicequalization and crossover functions.
Installation
The MB4 modular bass loudspeakercan be used with the Bose 1600 and1800 amplifiers. The MB4 plug-in EQcard must be used with theseamplifiers to provide active equaliza-tion for the system.
When used with the PANARAYsystem digital controller, the MB4speaker is also compatible withindustry standard amplifiers rated for4Ω to 8Ω loads.
The MB4 speaker is packaged oneper carton.
Loudspeaker Configuration
Mixer
PANARAY systemdigital controller
1800-VI amplifierwith 802®-III EQcard
AmplifierAmplifier
802-IIIspeaker
802-IIIspeaker MB4
speaker
MB4speaker
MB4speaker
802-IIIspeaker
802-IIIspeaker
Accessories
The following versatile accessoriesare available from Bose:
• MB4 single-unit wall mountbracket
• MB4 endfire 2x bass arraybracket
• MB4 endfire 4x bass arraybracket
• MB4 broadside 2x bass arraybracket
Installation and user instructions areincluded with the loudspeaker.
MB4 modular bass loudspeakers aredesigned to be wall mounted. Theycan also be assembled into bassarrays, by using the MB4 endfire orbroadside brackets in conjunctionwith the Bose PANARAY systemdigital controller.
No stands are required for portableuse.
1800-VI amplifierwith MB4 EQ card
Mixer
MB4speaker
Dimensions
18.1"459mm
8.6"219mm
10.2"260mm
12.2"310mm
18.1"459mm
23"583mm
26.7"677mm
10.2"260mm
23"583mm
26.7"677mm
Top View
Side View
Back View
M8
©2001 Bose Corporation, The MountainFramingham, MA 01701-9168www.bose.com261284 AM Rev.00 PC028150 JN20369