palm-3000 p3k fpdp carrier board review dean palmer building 318, room 125 november 10, 2009 8:00 am...
Post on 20-Dec-2015
214 views
TRANSCRIPT
PALM-3000
P3K FPDP Carrier Board Review
Dean Palmer
Building 318, Room 125
November 10, 2009
8:00 am – 12:00 pm
PALM-3000Presentation Outline
• Introduction• Link Requirements • Link Components• Board Requirements• Board Design• FPGA Design• Schedule • Discussion
PALM-3000Introduction
• Purpose– Provide a high speed data link system which
connects distributed devices (RTC Subsystem) through a highly specialized communications protocol optimized for maximum data throughput to our active mirror electronics.
– Data transfers occur without the CPU overhead and non-deterministic latencies associated with many layers of complex protocols
– Must interface with the new mirror electronics as well as the old electronics
– Must be able to maintain speed requirements over a length of 300’
PALM-3000Link Requirements
• In order to keep the system loop delay small, the link speed must be fast and have low-latency.
• The total time from first data out until the DM actuators are settled must be < 100 µsec (TBR).(< 50 µsec was desired but we know we can’t meet that.) We will try for < 70 µsec.– Xinetics first-in to all settled time is 37 µsec. (typ.)
– This leaves about 30 µsec for the link transfer.
• Required link data rate is about 226 MB/sec.(3388 chan. x 2 Bytes per chan.) / 30 µsec ~= 226 MB/sec
4
PALM-3000
5
DM High-Speed Data Link
Transmit End• Curtiss Wright FibreXtreme SL240 PCIe 2.5 Gb/s Data Link Card
– Up to 247 MB/s per channel sustained data rate per channel
– Low overhead ANSI/VITA 17.1-2003 Serial FPDP Protocol• Based on Fiber Channel. Uses similar ordered sets
– Low latency (about 1us)
– 4 independent channels
PALM-3000DM High-Speed Data Link
Receive End• Curtiss Wright FibreXtreme SL240 CMC 2.5 Gb/s Data Link Card
– IEEE P1386 Common Mezzanine Card form factor (same as PMC)
– 32-bit parallel FPDP data bus @ 62.5 MHz
•Custom Carrier Board–6U VME form factor. FPGA based.
–Four SOR-422U parallel output ports for connection to Xinetics Drivers.
–P1 port for connection to LODM and TTM amplifiers.
PALM-3000DM High-Speed Data Link Architecture
PC0COTS
Serial FPDPPCIe card
DM Interface Box
Existing DM DriverChassis
Custom FPDP to DM Carrier Card
COTSSerial FPDPCMC card
Xinetics DM Driver Chassis
Xinetics DM Driver Chassis
Xinetics DM Driver Chassis
Xinetics DM Driver Chassis
Custom FPDP to DM Carrier Card
COTSSerial FPDPCMC card
P1
Duplex Fibersw/ LC Connectors
LVDS
TTM Interface Box
Custom FPDP to DM Carrier Card
COTSSerial FPDPCMC card
DM Interface Box
Custom FPDP to DM Carrier Card
COTSSerial FPDPCMC card
Xinetics DM Driver Chassis
Xinetics DM Driver Chassis
Xinetics DM Driver Chassis
Xinetics DM Driver Chassis
High-Voltage
Driver Card
P1
P1
PALM-3000
P3K FPDP Carrier Board Requirements
• The board must host the FPDP CMC card– Must provide physical area and mounting holes.
– Must supply connectors for electrical interface.
– Must supply power (3.3 VDC @ 1.4 A avg. 1.7 A peak)
• The board must have an FPGA for processing data– Including power supplies and associated interfaces.
• The board must have 4 outputs to Xinetics drive chassis.• The board must have a P1 interface for JPL chassis.• The board must provide Vref to JPL chassis.• The board must buffer Vmon from the JPL chassis• The board should have an A/D converter and mux.• The board should have 1 or 2 RS-232 ports (for future)
8
PALM-3000
9
FPDP Carrier Board Block Diagram(Xinetics Interface)
Curtiss Wright sFPDP CMC
Module
Xilinx Virtex-4 FPGA
RS-232
PROM, JTAG, Clock and
Reset
SOR422-U Output
Analog Inputs
FPDP Transmit
Configuration
FPDP Receive
SOR422-U Output
SOR422-U Output
SOR422-U Output
5V to 3.3V Power Converter
Core Voltage Regulators
1.8V
1.2V2.5V
PALM-3000
10
FPDP Carrier Board Block Diagram(JPL Interface)
Curtiss Wright sFPDP CMC
Module
Xilinx Virtex-4 FPGA
RS-232
PROM, JTAG, Clock and
Reset
VME P1 Output(for LODM)
Analog Inputs
FPDP Transmit
Configuration
FPDP Receive
5V to 3.3V Power Converter
Core Voltage Regulators
1.8V
1.2V2.5V
PALM-3000FPDP CMC Board Interface
• This board has three connectors– One connector, P3, is for configuration via fixed signals or a
microprocessor interface– One connector, P4 is an FPDP transmitter.– One connector, P6 is an FPDP receiver.
11
1 23 45 67 89 10
11 1213 1415 1617 1819 2021 2223 2425 2627 2829 3031 3233 3435 3637 3839 4041 4243 4445 4647 4849 5051 5253 5455 5657 5859 6061 6263 64
J1
71439-0164
1 23 45 67 89 10
11 1213 1415 1617 1819 2021 2223 2425 2627 2829 3031 3233 3435 3637 3839 4041 4243 4445 4647 4849 5051 5253 5455 5657 5859 6061 6263 64
J2
71439-0164
1 23 45 67 89 10
11 1213 1415 1617 1819 2021 2223 2425 2627 2829 3031 3233 3435 3637 3839 4041 4243 4445 4647 4849 5051 5253 5455 5657 5859 6061 6263 64
J3
71439-0164
ad0ad1
ad2 ad3ad4
ad5ad6 ad7ad8
ad9ad10 ad11ad12
ad13ad14 ad15
pio2_in pio2_outpio1_inpio1_out
reset_n
rd0rd1rd2
rd3rd4rd5rd6rd7rd8
rd9rd10rd11rd12rd13rd14
rd15rd16rd17rd18rd19rd20
rd21rd22rd23rd24rd25rd26
rd27rd28rd29rd30rd31
td0td1
td2 td3td4 td5td6 td7td8 td9
td10
td11 td12td13 td14td15 td16td17 td18td19
td20 td21td22 td23
td24td25
td26 td27td28
td29td30td31
sel_nmcu_present_n
crc_en
clk_cfg0clk_cfg1
ignore_fcconvert_sync
RESERVED
RESERVED
RESERVEDRESERVED
int_n
ren_nwen_n
ads_nmclk
cfg0cfg1
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GNDGND
GND
GND
GND
GND
GND
GND
3V3
3V3
3V3
3V3
terrorreset_n
tsync_ntdir_ntdvalid_ntsuspend_n
tnrdy_ntstrobe
pio1_inpio1_out
pio2_outpio2_in
GND
GNDGND
GNDGND
GND
GND
GND
GND
GND
GNDGND
+5VD
+5VD
+5VD
+5VD
+5VD
+5VD
+5VD
+5VD
+5VD
+5VD
GND
GND
GND
GND
GND
GND
GNDGND
GND
GND
GND
GND
GND
ad[15..0]ad[15..0]
td[31..0]td[31..0]
pio1_out
pio2_outreset_n
pio2_in
pio1_in
rerrorrnrdy_n
rstrobe
rsync_n
+5VD
rsuspend_n
rdvalid_n
rdir_n
GND
rd[31..0]rd[31..0]
Configuration Signal Interconnets
Destination Card Signal Interconnets
Source Card Signal Interconnets
3V33V3
GND
pecl_inpecl_in_n
1 2 3 4 5 6 7 8
16 15 14 13 12 11 10 9
4.7KR6
123456
121110987
TDA06H0SB1
S1
GND
1 2 3 4 5 6 7 8
16 15 14 13 12 11 10 9
4.7KR7
GND
PALM-3000
FPDP CMC Board Interface (cont.)
12
66 5
3
2 1 0
4
4
1 2 3 4 5 6 7 8
16 15 14 13 12 11 10 9
2
1
2
1
21
12
1
2
2 1
1
2
2
1
1
2
1 2 3
456
123456
7 8 9 10 11 12
2
1
2
1
2
1
61
64 62 60 58 56 54 52 50 48 46 44 42 40 38 36 34 32 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2
63 59 57 55 53 51 49 47 45 43 41 39 37 35 33 31 29 27 25 23 21 19 17 15 13 11 9 7 5 3 1
00
135791113151719212325272931333537394143454749515355575963
246810121416182022242628303234363840424446485052545658606264
61
0 0
135791113151719212325272931333537394143454749515355575963
246810121416182022242628303234363840424446485052545658606264
61
0 0
2
1
2
1
2 1
1
2
2
1
1
2
2
1
1
2
12345678
161514131211109
PALM-3000RS-232
13
TX1
RX1
TX2
RX2
1
2
3
4
5
6
7
8
9
11
10
J4
13
10
11
8
12
9
14
7
C1+1
C2+4
GND15
C1-3
VCC16
C2-5
V-6
V+2
U15
SN65C3232EDWR
0.47uF
C106
1206 50V
3V3
100
R44
0805 1%
100
R45
0805 1%
RS232 A
RS232 B
0.1uF
C107
1206 50V0.1uF
C105
1206 50V
0.1uF
C108
1206 50V
0.1uF
C109
1206 50V123456789
10
P2
N2510-6V0C-RB
• Allows serial communications for future applications.• Borrowed design from Chris’s PZT driver board.•Benign design
• single IC runs on 3.3V• built charge pumps for RS-232 rails
U_PZT_RS232
2
1
2
1
6
7
8
9
10
5
4
3
2
1
12
21
2 1
2
1 1
2
5
9
4
8
3
7
2
6
1
10 11
910111213141516
87654321
PALM-30003.3 Volt Converter
• Design borrowed from SIM Motor Board.• IC is a multi-chip module.• Input is 5 to 30 Volts.• Output current is 5 A continuous 7 A peak.
14
Vin
A1
Vin
A2
Vin
A3
Vin
A4
Vin
A5
Vin
A6
Vin
B1
Vin
B2
Vin
B3
Vin
B4
Vin
B5
Vin
B6
Vin
C1
Vin
C2
Vin
C3
Vin
C4
Vin
C5
Vin
C6
PGN
DD
1
PGN
DD
2
PGN
DD
3
PGN
DD
4
PGN
DD
5
PGN
DD
6
PGN
DE
1
PGN
DE
2
PGN
DE
3
PGN
DE
4
PGN
DE
5
PGN
DE
6
PGN
DE
7
PGN
DE
8
PGN
DF1
PGN
DF2
PGN
DF3
PGN
DF4
PGN
DF5
PGN
DF6
PGN
DF7
PGN
DF8
PGN
DF9
PGN
DG
1
PGN
DG
2
PGN
DG
3
PGN
DG
4
PGN
DG
5
PGN
DG
6
PGN
DG
7
PGN
DG
8
PGN
DG
9
PGN
DG
10
PGN
DG
11
PGN
DH
1
PGN
DH
2
PGN
DH
3
PGN
DH
4
PGN
DH
5
PGN
DH
6
PGN
DH
7
PGN
DH
8
PGN
DH
9
PGN
DH
10
PGN
DH
11
Vou
tJ1
Vou
tJ2
Vou
tJ3
Vou
tJ4
Vou
tJ5
Vou
tJ6
Vou
tJ7
Vou
tJ8
Vou
tJ9
Vou
tJ1
0
Vou
tJ1
1
Vou
tK
1
Vou
tK
2
Vou
tK
3
Vou
tK
4
Vou
tK
5
Vou
tK
6
Vout K7
VoutK8
VoutK9
VoutK10
Vout K11
VoutL1
VoutL2
Vout L3
Vout L4
Vout L5
VoutL6
VoutL7
VoutL8
Vout L9
Vout L10
Vout L11
VoutM1
VoutM2
Vout M3
Vout M4
Vout M5
Vout M6
VoutM7
VoutM8
Vout M9
Vout M10
Vout M11
INTVccA7
PLL
INA
8
TRACK/SSA9
RUNA10
COMPA11
MPGMA12
MPGMB11
VD
B7
NCJ12
RUNB9
FsetB12
VD
C7
DRVccC10
MARG1C11MARG0C12
SGN
DD
9
COMPD11
MARG1 D12
DRVccE11
DRVccE12
VFB F12
PGOODG12
SGN
DH
12
FCB M12NCK12NCL12
U6LTM4612
+5VD
D1DFLS240L
10uF
C6
C2220 50V
+5VD
191k
R10
0805 1%
100kR8
0805 1%100kR9
0805 1%
+5VD
3V3
ps_sync_3v3
0.01uFC12
0603 50V
22.1kR11
0805 1%
392kR12
0805 1%
22pFC11
0603 50V NPO
220uFC9
T495D 6V22uFC10
C1210 6.3V
3V3
10uF
C8
C2220 50V
10uF
C7
C2220 50V
U_3V3_Pow er_Converter
2
1 1
2
2
1
M12
G12G11G10G9G8G7
H7 H8 H9 H10 H11 H12
J7 J8 J9 J10 J11 J12
K7 K8 K9 K10 K11 K12
M11M10M9M8M7
L7 L8 L9 L10 L11 L12
M1
G1 G2 G3 G4 G5 G6
H6H5H4H3H2H1
J6J5J4J3J2J1
K6K5K4K3K2K1
M2 M3 M4 M5 M6
L6L5L4L3L2L1
B12B11B9B1 B2 B3 B4 B5 B7B6
A6 A7A5A4A3A2 A8 A9 A10 A11 A12
C12C11C10C1 C2 C3 C4 C5 C7C6
D12D11D9D1 D2 D3 D4 D5 D6
E12E11E8E1 E2 E3 E4 E5 E7E6
F 6 F 7F 5F 4F 3F 2F 1 F 8 F 9 F 12
A1
1
2
12
2 1
1
2
2
1
1 2
1 2
1 2
12
12
PALM-3000LT Spice Simulation of 3.3 V
• 2 msec risetime on input power; 2 A load at power-up
• Full Load (7 A) at 11 msec. Back to 2 A at 13 msec.
15
PALM-3000Core Power Regulators
• Supplies 2.5V and 1.2V to the FPGA, Reset Circuit, and JTAG port.• Supplies 2.5V and 1.8V to the PROM.• Circuit design borrowed from Avnet Virtex-4 evaluation board.• Also used on SIM Motor Board.• Uses linear regulators.
16
100uFC21
T491D 16V
2V5
GND
1V2
3V3 1V8
47uFC18
T491D 20V
47uFC22
T491D 20V
3V3
GND
2V5
47uFC15
T491D 20V
/SD1
IN2
GN
D3
OUT4
ADJ5
TA
B6
U9 LP3966-ADJ
100uFC14
T491D 16V
0R17
0805 68pFC20
0805 50V NPO
/SD1
IN2
GN
D3
OUT 4
ADJ5
TA
B6
U7 LP3966-ADJ
10KR16
0603 1%
10KR13
0603 1%
10KR15
0603 1%
10.5KR14
0603 1%
0.1uFC23
0603 50V
/SD1
IN2
GN
D3
OUT4
SENSE5
TA
B6
U8 LP3966-1.8
100uFC17
T491D 16V0.1uFC19
0603 50V
68pFC13
0805 50V NPO
0.1uFC16
0603 50V
U_core_pow er
66
6
125 4 3
66
6
125 4 3
21
2 1
21
2
1
2
1
1 2
1 2
2
1
2
1
21
2
11
2
21
2 1
21
12
345 2 1
6
6 6
PALM-3000SOR-422U Output Ports
• Xinetics proprietary interface and protocol.• Uses LVDS Signaling. Using DS90LV047A driver IC.
17
PALM-3000SOR-422U Output Ports (cont.)
18
EN1
IN 12
IN 23
IN 36
IN 47
EN8
Vcc4
GND5
OUT 4– 9OUT 4+ 10OUT 3+ 11OUT 3– 12OUT 2– 13OUT 2+ 14OUT 1+ 15OUT 1– 16U1
DS90LV047ATMTC
EN1
IN 12
IN 23
IN 36
IN 47
EN8
Vcc4
GND5
OUT 4– 9OUT 4+ 10OUT 3+ 11OUT 3– 12OUT 2– 13OUT 2+ 14OUT 1+ 15OUT 1– 16
U2
DS90LV047ATMTC
3V3
3V3
data0data1
data2data3
data4data5
data6data7
0.1uF
C1
0603 50V
0.1uF
C2
0603 50V
3V3
3V3
DATA0_PDATA0_N
DATA1_PDATA1_NDATA2_NDATA2_PDATA3_PDATA3_N
DATA4_NDATA4_P
DATA5_NDATA5_P
DATA6_NDATA6_PDATA7_PDATA7_N
4.7KR2
0603 1%
3V3
4.7KR1
0603 1%
3V3
1nF
C150
0603 50V
1nF
C154
0603 50V
3V3
3V3
There are actually fiveof these devices
Using Micro-strip traces (except on ready signal).
This minimizes vias and stubs.
Mini D Ribbon (MDR) connector
1
2
121212
12
12
2 12 12 1
2 1
2 11
2
1
2
1
2
1
2
1
2
51 52
5251
DATA0_PDATA0_N
DATA1_PDATA1_NDATA2_N
DATA2_P DATA3_PDATA3_N
DATA4_NDATA4_P DATA5_N
DATA5_P
DATA6_NDATA6_P
DATA7_PDATA7_N
DATA8_NDATA8_P
DATA9_PDATA9_N
DATA10_NDATA10_P
DATA11_PDATA11_N
DATA12_NDATA12_P DATA13_P
DATA13_NDATA14_NDATA14_P DATA15_P
DATA15_N
CLOCK_PCLOCK_N
ENABLE/_PENABLE/_N
FRAME/_PFRAME/_N
READY/_NREADY/_P
0R78 (R78.1, ...)
0805
drain
1
20
23456789
10111213141516171819
3029282726
2524232221
40393837363534333231
50494847464544434241
52 51
J5 (J5.1, ...)
10250-1S10PE
drain
drainch
assi
sch
assi
s
drain
drain
drain
drain
PALM-3000SOR-422U Cables
• We plan on clocking the SOR-422U ports at 62.5 MHz. This requires us to pay attention to the quality of the interconnect.
• We plan on using a COTS cable made by 3M– Designed for LVDS signaling.– Contains 20 shielded 100 Ohm pairs + 6 grounds.– High-Density 50 position MDR connector.– Part number for 1m cable: 14150-EZBB-100-0LC
• This cable requires an adapter and short ribbon cable at the Driver Chassis end to go from MDR to a standard 50-pin header.
19
PALM-3000SOR-422U Cables (cont.)
20
Notice how the signal order reverses at opposite ends (except Link and ICMB).
PALM-3000Adapter PCB
21
MH2
MH1
12
34
56
78
910
1112
1314
1516
1718
1920
2122
2324
2526
2728
2930
3132
3334
3536
3738
3940
4142
4344
4546
4748
4950
21
51
52
51
52
52
51
1
20
23456789
10111213141516171819
3029282726
2524232221
40393837363534333231
50494847464544434241
52 51
J110250-1S10PE
chas
sis
chas
sis
DATA0_PDATA0_N
DATA1_PDATA1_N DATA2_N
DATA2_PDATA3_PDATA3_N
DATA4_NDATA4_PDATA5_N
DATA5_P
DATA6_NDATA6_P
DATA7_PDATA7_N
DATA8_NDATA8_P
DATA9_PDATA9_N
DATA10_NDATA10_P
DATA11_PDATA11_N
DATA12_NDATA12_PDATA13_P
DATA13_N DATA14_NDATA14_PDATA15_P
DATA15_N
CLOCK_PCLOCK_N
ENABLE/_PENABLE/_N
FRAME/_PFRAME/_N
READY/_NREADY/_P
drain
drain
drain
drain
drain
drain
1 23 45 67 89 1011 1213 1415 1617 1819 2021 2223 2425 2627 2829 3031 3233 3435 3637 3839 4041 4243 4445 4647 4849 50
P1
N3433-6302RB
DATA0_P DATA0_NDATA1_P DATA1_N
DATA2_NDATA2_PDATA3_P DATA3_NDATA4_P DATA4_NDATA5_P DATA5_NDATA6_P DATA6_NDATA7_P DATA7_NDATA8_P DATA8_NDATA9_P DATA9_NDATA10_P DATA10_NDATA11_P DATA11_NDATA12_P DATA12_NDATA13_P DATA13_NDATA14_P DATA14_NDATA15_P DATA15_N
CLOCK_P CLOCK_NENABLE/_P ENABLE/_NFRAME/_P FRAME/_NREADY/_P READY/_N
DGND DGND
PALM-3000Analog Inputs
• Provide a test input for optional use if needed.– Could be used for test waveforms– Could be used for current monitor for JPL Drive
• Plan on adding an analog mux for power supply monitoring.
22
VIN23
1 8
GND4 TRIM 5VOUT 6
7
U24
ADR431ARZ
+5VA
0.47uF
C1521206 50V
AGND
22.1R77
0805 1%
AGND
0.47uF
C1531206 50V
AGND
+2.5VA
VIO 10REF1
VD
D2
GN
D5
IN+3 SDI 9
SCK 8IN-4
SDO 7
CNV6
U23AD7980ARMZ
AGND
AGND
test_sdi
test_sck
test_cnv
test_sdo
2.5VA
0.47uF
C146
1206 50V
AGND
3V3
0.47uF
C149
1206 50V10uF
C148
C2220 50V
AGND
+5VA
30.1
R74
1206 1%
5
67B
U21BAD8666ARZ
0.47uFC151
1206 50V NPO
100
R75
0805 1%
AGND
P4
AGND
VtestDFLS240L-7D10
DFLS240L-7D11
AGND
+5VA
TEST INPUT
PALM-3000Analog Inputs (cont.)
23
1
2
3
4
8
7
6
5
1
2
3
4
8
7
6
5
2
1
2 1
2
1
21
21
12
2 1
12
2 2
1 2 21
2
1
2
1
21
2
1
2
1
2
1
12
2 1
2
1
2
1
21
2
1
• Analog ground plane pour on top layer.• +5VA and –5VA plane pours on Mid-Layer 3 and 4• +2.5VA plane pour on Mid-Layer 2.
PALM-3000VME P1 Interface (for JPL board)
• This interface is the same as used on the present DM receiver board except for the bus transceiver IC’s
• Using the SN74VMEH22501A device made especially for driving VME backplanes. These devices use 3.3 volt signaling but are 5V tolerant.
• The analog portion (Vref and Vmon) portions are virtually the same except for a few minor changes suggested by Chris Shelton.
24
98 97
A2A3A4A5A6A7A8A9A10A11A12A13A14A15A16A17A18A19A20A21A22A23A24A25A26A27A28A29A30A31A32
B32
C32
B31
C31
B30
C30
B29
C29
B28 B27 B26
C26C27C28
B1
A1
C1
B2B3
C2C3
B4B5B6B7
C4C5C6C7C8C9C10C11
B8B9B10B11B12B13B14B15B16
C12C13C14C15C16C17C18C19C20C21
B17B18B19B20B21
C22C23C24C25
B22B23B24B25
1
2
1
2
2
1
2
1
2
1
2
11
2
1
2
1
2
2
1
1
2
2
1
21
1
2
2 112
2 1 12 2 1 12
2 112
2 1 12 2 1 12
2 112
2 1 12 2 1 12
2
1
2
1
2
1
2
1
2 112
2 1 12 2 1 12
2
1
2
1
2
1
2
1Digital Portion
of Interface
PALM-3000Power Estimates
25
P3K FPDP Power Consumption Estimate Dean Palmer, 11/9/2009
ID Parts Description Voltage Current # IndvMin Total(mW)IndvMax Total(mW)0 AD8666ARZ ADC preamp +5VA, - 5VA 1.1mA to 2mA 1 5.5 5.5 10 101 DS90LV047ATMTC LVDS drivers 3V3 20mA to 30mA 20 13.2 264 26.4 5282 ECS-2033-320-BN 32 MHz crystal 3V3 13mA Max 1 43 43 43 433 LF353M Vmon and Vref amplifier +5VA, - 5VA 4mA to 7mA 1 20 20 35 354 LP3966ES-1.8V 1.8V linear regulator 3V3 10mA to 15mA 1 35 35 65 655 LP3966ES-ADJ linear regulators 3V3 10mA to 15mA 2 33 66 2500 50006 SN65C3232EDWR RS232 Transceiver 3V3 0.3mA to 4mA 1 1 1 330 3307 SN74VMEH22501A P1 bus drivers 3V3 30mA to 42mA 4 100 400 140 5608 TPS3808G12DBV reset 2V5 < 1mA 1 0.1 0.1 1 19 XC4VLX60-10FFG668C FPGA 3V3,2V5,1V2 167mA - 600mA 1 550 550 1980 198010 XCF32PVO48C PROM 2V5,1V8 45mA,10mA 1 7 7 130 130
MinPwr(W): 1.3861 MaxPwr(W):8.672
PALM-3000Bill of Materials
26
Bill of Materials:sFPDP CARRIER BOARDSource Data From: carrier.PrjPCBProject: carrier.PrjPCBReport Date: 10/6/2009 12:14:10 PMPrint Date: 11/6/2009 5:22:31 PM
Item Quantity Designator Part Number Description Footprint Manufacturer Supplier Unit Price Extension Notes1. 25 C12, C24, C26, C40, C41, C42, C43, C61, C62,
C63, C64, C65, C66, C67, C68, C91, C92, C93, C94, C95, C98, C99, C100, C101, C104
C0603C103J5RAC7411 capacitor, 0.01uF ±5% 50V size 0603 X7R ceramic chip 0603 Kemet Mouser Electronics $0.05 $1.25
2. 4 C105, C107, C108, C109 C1206C104J5RACTU capacitor, 0.1uF ±5% 50V size 1206 X7R ceramic chip 1206 Kemet Mouser Electronics $0.16 $0.643. 63 C1.1, C1.2, C1.3, C1.4, C2.1, C2.2, C2.3, C2.4,
C3.1, C3.2, C3.3, C3.4, C4.1, C4.2, C4.3, C4.4, C5.1, C5.2, C5.3, C5.4, C16, C19, C23, C25, C27, C29, C44, C45, C69, C70, C71, C72, C96, C97, C102, C103, C110, C113, C114, C116, C117, C118, C119, C120, C121, C122, C123, C124, C125, C126, C127, C128, C129, C130, C131, C132, C133, C134, C135, C136, C137, C138, C139
C0603C104K5RAC7013 capacitor, 0.1uF ±10% 50V size 0603 X7R ceramic chip 0603 Kemet Mouser Electronics $0.07 $4.41
4. 2 C145, C151 C1206C472J5GACTU capacitor, 0.47uF ±5% 50V size 1206 NPO ceramic chip 1206 Kemet Mouser Electronics $0.89 $1.785. 9 C106, C140, C141, C143, C144, C146, C149,
C152, C153C1206C474K5RACTU capacitor, 0.47uF ±10% 50V size 1206 X7R ceramic chip 1206 Kemet Mouser Electronics $0.55 $4.95
6. 20 C150.1, C150.2, C150.3, C150.4, C154.1, C154.2, C154.3, C154.4, C155.1, C155.2, C155.3, C155.4, C156.1, C156.2, C156.3, C156.4, C157.1, C157.2, C157.3, C157.4
C0603C102J5RACTU capacitor, 1nF ±10% 50V size 0603 X7R ceramic chip 0603 Kemet Mouser Electronics $0.05 $1.00
7. 1 C147 C1206C102J5GACTU capacitor, 1nF ±10% 50V size 1206 NPO ceramic chip 1206 Kemet Mouser Electronics $0.15 $0.158. 2 C111, C112 C1206C105K5RACTU capacitor, 1uF ±10% 50V size 1206 X7R ceramic chip 1206 Kemet Mouser Electronics $0.26 $0.529. 6 C6, C7, C8, C115, C142, C148 C5750X7R1H106K capacitor, 10uF 10% 50V size 2220 X7R ceramic chip 2220 TDK Digikey $5.01 $30.03
10. 1 C11 C0603C220G5GACTU capacitor, 22pF ±1% 50V size 0603 COG ceramic chip 0603 Kemet Mouser Electronics $0.41 $0.4111. 1 C10 C1210C226K9PACTU capacitor, 22uF ±10% 6.3V size 1210 X5R ceramic chip 1210 Kemet Mouser Electronics $1.90 $1.9012. 4 C30, C60, C89, C90 T491B476K010AT capacitor, 47uF ±10% 10V size 3528-21 solid tantalum chip B Kemet Mouser Electronics $0.49 $1.9613. 3 C15, C18, C22 T495D476K020ATE100 capacitor, 47uF ±10% 20V size 7343-31 low ESR solid tantalum chip D Kemet Mouser Electronics $1.32 $3.9614. 2 C13, C20 C0603C680G5GACTU capacitor, 68pF ±2% 50V size 0805 COG ceramic chip 0805 Kemet Mouser Electronics $0.74 $1.4815. 3 C14, C17, C21 594D107X9016D2T capacitor, 100uF ±10% 16V size 7343-31 low ESR solid tantalum chip D Vishay/Sprague Mouser Electronics $2.85 $8.5516. 1 C9 T495D227K006ATE045 capacitor, 220uF ±10% 6V size 3528-21 low ESR solid tantalum chip D Kemet Mouser Electronics $5.22 $5.2217. 39 C31, C32, C33, C34, C35, C36, C37, C38, C39,
C46, C47, C48, C49, C50, C51, C52, C53, C54, C55, C56, C57, C58, C59, C73, C74, C75, C76, C77, C78, C79, C80, C81, C82, C83, C84, C85, C86, C87, C88
C0402C681J5RACTU capacitor, 680pF ±5% 50V size 0402 X7R ceramic chip 0402 Kemet Mouser Electronics $0.05 $1.95
18. 1 C28 C0603 capacitor, size 0603 chip 0603 Kemet $0.00 $0.00 This item not installed19. 2 J4, J5 1734354-2 connector, 9-pin R/A D-Sub receptacle DB-9_F Amp Mouser Electronics $1.47 $2.9420. 1 P3 98424-G52-14ALF connector, 14 position 2mm pitch dual-row straight SMD header SMT 14-PIN HEADER FCI Digikey $1.44 $1.4421. 3 J1, J2, J3 71439-0164 connector, 32 position 1mm pitch dual-row mezzanine receptacle Molex, Inc. Mouser Electronics $5.99 $17.9722. 1 P1 5650947-5 connector, 96 pin DIN right angle DIN96M Amp Mouser Electronics $3.00 $3.0023. 3 J6, J7, P4 5227161-7 connector, right angle PCB mount BNC BNC_RA CON Amp Mouser Electronics $1.65 $4.9524. 3 D1, D10, D11 DFLS240L-7 diode, 40V 2A schottky rectifier DFLS240L Diodes Inc. Digikey $0.63 $1.8925. 8 D2, D3, D4, D5, D6, D7, D8, D9 598-8040-107F diode, 160mcd 595nm size 0603 standard yellow LED 3-0603 Mouser Electronics $0.10 $0.8026. 4 P2.1, P2.2, P2.3, P2.4 header, 25-Pin, Dual row HDR2X25 $5.00 $20.0027. 2 U7, U9 LP3966ES-ADJ/NOPB ic, 1.2V to 5V adjustable low-dropout regulator TO263 - 5 National Semiconductor Digikey $4.13 $8.2628. 1 U8 LP3966ES-1.8/NOPB ic, 1.8V 3A ultra-low dropout voltage regulator TO263 - 5 National Semiconductor Digikey $4.13 $4.1329. 1 U24 ADR431ARZ ic, 2.5V XFET voltage reference SOIC8 Analog Devices Digikey $6.36 $6.3630. 1 U6 LTM4612IV#PBF ic, 5A DC to DC µmodule LGA Package Linear Technology Digikey $46.50 $46.5031. 4 U16, U17, U19, U20 SN74VMEH22501ADGGR ic, 8-Bit Universal Bus Transceiver DGG048 Texas Instruments Digikey $5.18 $20.7232. 1 U13 ECS-2033-320-BN ic, 10 MHz 3.3V clock oscillator ECS-2033 ECS Inc Digikey $5.94 $5.9433. 2 U22, U23 AD7980ARMZRL7 ic, 16-bit 1MSPS pseudo-differential input ADC MSOP10 Analog Devices Digikey $20.07 $40.1434. 1 U21 AD8666ARZ ic, 16V 4MHz R-R output amplifier SOIC8 Analog Devices Digikey $2.52 $2.5235. 1 U18 LF353M/NOPB ic, dual wide-bandwidth JFET input op-amp SOIC8 National Semiconductor Digikey $1.24 $1.2436. 1 U12 TPS3808G12DBV ic, programmable delay 1.2V voltage supervisor SOT23-6 Texas Instruments Digikey $1.75 $1.7537. 20 U1.1, U1.2, U1.3, U1.4, U2.1, U2.2, U2.3, U2.4,
U3.1, U3.2, U3.3, U3.4, U4.1, U4.2, U4.3, U4.4, U5.1, U5.2, U5.3, U5.4
DS90LV047ATMTC/NOPB ic, quad 3V LVDS CMOS differential line driver MTC16_N National Semiconductor Digikey $2.90 $58.00
38. 1 U15 SN65C3232EDWR ic, RS-232 line driver / receiver SOIC16W Texas Instruments Digikey $1.88 $1.8839. 1 U11 XCF32PVO48C ic, XCF00P Series 1.8V 32-Megabit Configuration PROM VO48 Xilinx Avnet $27.79 $27.7940. 1 U10 XC4VLX60-10FFG668C ic, Xilinx Virtex-4 LX Platform FPGA, 668-Ball FFBGA, Speed Grade 10 FFG668 Xilinx Digikey $609.60 $609.6041. 5 R17, R78.1, R78.2, R78.3, R78.4 CRCW08050000Z0EA resistor, 0 Ohm 1/8W size 0805 thick film chip jumper 6-0805 Vishay/Dale Mouser Electronics $0.05 $0.2542. 3 R41, R42, R64 CRCW06031K00FKEA resistor, 1.00K Ohm ±1% 1/10W size 0603 thick film chip 3-0603 Vishay/Dale Mouser Electronics $0.02 $0.0643. 49 R1.1, R1.2, R1.3, R1.4, R2.1, R2.2, R2.3, R2.4,
R3.1, R3.2, R3.3, R3.4, R4.1, R4.2, R4.3, R4.4, R5.1, R5.2, R5.3, R5.4, R27, R28, R29, R30, R31, R32, R33, R39, R40, R46, R47, R48, R49, R50, R51, R52, R53, R54, R55, R56, R57, R59, R60, R62, R63, R65, R66, R67, R68
CRCW06034K70FKEA resistor, 4.70K Ohm ±1% 1/10W size 0603 thick film chip 3-0603 Vishay/Dale Mouser Electronics $0.06 $2.94
44. 4 R13, R15, R16, R43 CRCW060310K0FKEA resistor, 10.0K Ohm ±1% 1/10W size 0603 thick film chip 3-0603 Vishay/Dale Mouser Electronics $0.02 $0.0845. 1 R14 CRCW060310K5FKEA resistor, 10.5K Ohm ±1% 1/10W size 0603 thick film chip 3-0603 Vishay/Dale Mouser Electronics $0.02 $0.0246. 1 R11 CRCW080522K1FKEA resistor, 22.1K Ohm ±1% 1/8W size 0805 thick film chip 6-0805 Vishay/Dale Mouser Electronics $0.05 $0.0547. 3 R69, R72, R77 CRCW080522R1FKEA resistor, 22.1 Ohm ±1% 1/8W size 0805 thick film chip 6-0805 Vishay/Dale Mouser Electronics $0.05 $0.1548. 2 R70, R74 CRCW120630R1FKEA resistor, 30.1 Ohm ±1% 1/4W size 1206 thick film chip 1206 Vishay/Dale Mouser Electronics $0.10 $0.2049. 1 R38 CRCW060347K0FKEA resistor, 47.0K Ohm ±1% 1/10W size 0603 thick film chip 3-0603 Vishay/Dale Mouser Electronics $0.06 $0.0650. 2 R8, R9 CRCW0805100KFKEA resistor, 100K Ohm ±1% 1/8W size 0805 thick film chip 6-0805 Vishay/Dale Mouser Electronics $0.05 $0.1051. 7 R44, R45, R58, R71, R73, R75, R76 CRCW0805100RFKEA resistor, 100 Ohm ±1% 1/8W size 0805 thick film chip 6-0805 Vishay/Dale Mouser Electronics $0.05 $0.3552. 1 R10 CRCW0805191KFKEA resistor, 191K Ohm ±1% 1/8W size 0805 thick film chip 6-0805 Vishay/Dale Mouser Electronics $0.05 $0.0553. 8 R19, R20, R21, R22, R23, R24, R25, R26 CRCW0603249RFKEA resistor, 247 Ohm ±1% 1/10W size 0603 thick film chip 3-0603 Vishay/Dale Mouser Electronics $0.06 $0.4854. 1 R12 CRCW0805392KFKEA resistor, 392K Ohm ±1% 1/8W size 0805 thick film chip 6-0805 Vishay/Dale Mouser Electronics $0.05 $0.0555. 3 R6, R7, R18 4816P-T01-472LF resistor network, 4.7K ±2% 1.3W 16-pin isolated SMD thick-film SOIC-16 Bourns Mouser Electronics $0.46 $1.3856. 1 S4 TDA04H0SB1 switch, 1/2 pitch 4-position SPST DIP SO8 C&K Components Mouser Electronics $1.70 $1.7057. 1 S1 TDA06H0SB1 switch, 1/2 pitch 6-position SPST DIP DIP-12/SW C&K Components Mouser Electronics $2.03 $2.0358. 1 S2 BPA08SB switch, 8-position side actuation SPST DIP DIP_SW_8WAY_SMD C&K Components Mouser Electronics $1.65 $1.6559. 1 S3 EVQ-QXS01W switch, 15VDC 0.02A SPST-NO pushbutton EVQ-QXS01W Panasonic Digikey $0.96 $0.9660. 1 Q1 DMP2004TK-7 transistor, 20V 150mW low-threshold voltage P-Channel MOSFET SOT-523 Diodes Inc Digikey $0.60 $0.6061. 1 R61 RJ24FX104 variable resistor, 100K ±10% 1/2W 25-turn cermet VR5 Mouser Electronics $4.62 $4.62
Total $975.76