1) INORGANIC ZINC PRIMER2) HIGH BUILD POLYAMIDE-CURED EPOXY PRIMER WITH ZINC PHOSPHATAE3) ZINC RICH EPOXY PRIMER4) POLY AMIDE ADDUCT CURED HIGH BIULD, HIGH SOLID EPOXY PRIMER5) AMINE ADDUCT CURED PHONOLIC EPOXY (NOVALAC)

6) EPOXY/AMINE ADDUCT COATING SYSTEM7) AMINE ADDUCT SOLVANT FREE EPOXY PHENOLIC COATING SYSTEM (SELF PRIMING)8) GLASS FLAKE POLYESTER COATING (SELF PRIMING)9) GLASS FLAKE VINYL ESTER COATING SYSTEM FOR HEAVY(SELF PRIMING)10) 100% SOLID, GLASS FLAKE EPOXY COATINGFOR IMMERSSION SERVICES UP TO 105C10) CERAMIC/INORGANIC FILLED EPOXY PHENOLIC/NOVALAC COATINGCeramic/Inorganic Filled Epoxy-Phenolic/NovolacCoating for Immersion Service up to 150C12) COAL TAR EPOXY PRIMER13) ZINC PHOSPHATE ALKYYD PRIMER COATINGSYSTEM14) RADIANT HEAT INSULATING COATING SYSTEM.15) HOT INSULATING COATING SYSTEM16) CHLORINATED RUBBER COATINGSYSTEM( SELF PRIMING)17) BITUMINOUS PAINT SYSTEM( SELF PRIMING)18) SILICON ALUMINIUM VERY HIGH TEMPERATURE COATING SYSTEM ( SELF PRIMING)19) AIR DRYING, SINGLE COMPONENT, HIGH HEAT EXTERNAL COATING FOR BARE AND INSULATED CARBON STEEL AND AUSTENITIC STAINLESS STEEL.20) HAND APPLIED SPLASH ZONE COMPOUND21) SPRAY APPLIED SPLASH ZONE COMPOUND22) GLASS FLAKE REINFORCED AMINE ADDUCT CURED EPOXY COATING SYSTEM

23) POLY AMINE CURE EPOXY PAINT FOR DAMP SURFACES-TWO COAT SYSTEM24) MODIFIED EPOXY BARRIER COAT FOR DAMP SURFACES-SINGLE COAT25) HIGH TEMPERATURE MASTIC PAINT FOR BURRIED OR IMMERSION SERVICES (SELFPRIMING)26) POLYAMIDE ADDUCT CURED EPOXY PAINT27) SOLVANT FREE TWO ULTRA HYBRID EPOXY COATING SYSTEM FOR IMMERSION SERVICES

28) Specialty Liquid Coating Systems for Pumps, Valves, Piping, Fitting and Exchanger Boxes.29) AMINE ADDUCT CURED EPOXY COATING (SELF PRIMING)

1) INORGANIC ZINC PRIMERInorganic Zinc Silicate.Outstanding weather resistance Abrasion resistance, excellent chemical resistance, for 6-9 PH a service range, high temperature applicationTwo component paintTwo type Solvent Base: Humidity shall be >50% Water Base : Humidity Shall be < 50%Thin film ThicknessCan be applied for carbon steel both insulation and non insulation.Service temperature normally 150-400 CCan be used as a general purpose heavy duty rust preventing Primer coat.As a single coat System: Can be used as a complete coating for long term protection of steel exposed to moderately to severely corrosive environment and abrasion Aramco APCS 17A, APCS 17B). Service condition limitation is 400c. Can be used under thermal insulation in cyclic cryogenic condition up to 77CAs a primer for 2 coat system: Can be used for as a primer for epoxy top coat (poly amide adduct cured epoxy) up to service temperature 150C for non insulated carbon steel for mild corrosive environment as well as severe atmospheric environment. (Aramco APCS 1A)And also can be used as a primer for Silicon Aluminum ( Aluminum Pigmented Polysiloxane) or Silicon Acrylic( Acrylic modified Plysiloxane) for high temperature atmospheric application for carbon steel.(Aramco APCS 11A)As a Primer of 3coat system: Can be used as a primer for poly amide adduct cured epoxy intermediate coat and Acrylic Poly Urethane enamel cured with adiabatic iso cynate Top coat up to 150 C service temperature for severe atmospheric services. Aramco APCS 1D)As tank lining as per sspc paint type 20-level 1.Resistant to permanent temperature as well as occasionally dry peak temperature up to 500 c resistance to cyclic dry temperature up to 400Cresistance to high temperature under humid conditionCan be used as a primer for the Aluminum Silicon Top coat for high temperature applications 150-400C

2) HIGH BUILD POLYAMIDE-CURED EPOXY PRIMER WITH ZINC PHOSPHATAETwo component systemTypical Use: Gneral purpose primer for steel and other metals in mild and Severe atmospheric exposure including exposure to many acids and alkalis

Service Temperature: Maximum150C

Can be used as a primer for poly amide adducts cured epoxy intermediate and top coat system.

Up to maximum service temperature 150C. (Aramco APCS 1B, APCS 12)Can be used as a primer for poly amide adduct cured epoxy intermediate and Acrylic Poly Urethane enamel cured with adiabatic iso cynate Top coat up to 150 C service temperature for severe atmospheric services top coat (Aramco APCS 1E)

3) ZINC RICH EPOXY PRIMERTwo component zinc rich epoxy primerHard wearing and highly weather resistant coation.Offer cathodic protection of local mechanical damage.Can be used for repairing of damaged galvanized layer.Maximum service temperature : 160CPrimer for epoxy, vinyl and acrylic coating system in mediam and severely corrosive enviorenment.

As a single coat system for repairing of galvanized layer in galvanized steels.( Aramco APCS 1C primer)Can be used as a primer for poly amide adduct cured epoxy top coat for mild . medium, severe atmospheric conditions for carbon steel upto 150C. (Aramco APCS 1C)Can be used as a primer for poly amide adduct cured epoxy intermediate and Acrilic Poly Urethane enamel cured with aliabatic iso cynate Top coat upto 150 C service temperature for severe atmospheric services. Aramco APCS 1F)

4) POLY AMIDE ADDUCT CURED HIGH BIULD, HIGH SOLID EPOXY PRIMERMaximum Service Temperature: 120CTwo Component paint systemHard and Tough coatingGood wetting propertiesLow Temperature Curing.Typical Usea) One coat for coating maintenance works, fast dry alternative to AluminumPigmented Alkayed Coating(APCS 4) and Alkayd Enamal (APCS 6)b) A coating for galvanized steel and aluminum for appearance orincreased chemical resistance.c) A maintenance coating over existing sound coatings.d) For new steel structures in mild corrosive areas

Can be used as a self primer. (Aramco APCS26)Can be used surface tolerance paint system.Can be used as a Intermediate paint system(Aramco APCS 1D,1E,1F) with Inorganic Zinc Silicate primer or epoxy primer(H.B Poly amide cured epoxy) or Zinc Rich Epoxy Primer and with Acrilic Polyurethane Top coat.Can be used as a primer and intermediate coat for Acrylic Polyurethane for atmospheric services upto temperature service 80C. (Aramco APCS 26T)Can be used as a Finish coat paint system( Aramco APCS 1A, 1B, 1C) with Inorganic Zinc Silicate primer or epoxy primer(H.B Poly amide adduct cured epoxy) or Zinc Rich Epoxy Primer FOR Atmospheric Services with mild and severe corrosive enviorenment.Multi purpose coating as per specification for maintenance and minor repaires in immersed areas including ballast tanks and underwater hull Specially in those cases where extended recoating properties for PU top coat are requested.Can be used directly on cured zinc silicate as a top coat.As a top coat where the usual outdoor cosmetic appearance of epoxy paints is acceptable.

5) AMINE ADDUCT CURED PHONOLIC EPOXY (NOVALAC)Maximum ServiceTemperature: 160CSuitable for insulated and non insulated Carbon steelCan be used internal and external carbon steel surfaces.Two component paint systemVery good adhesionHigh temperature ResistanceHigh water ResistanceHigh chemical ResistanceTypical UseImmersion service particularly for raw or treated waters and for GOSP traps handling hot crude oil/brine solutions.Suitable for potable water.As an interior lining Tanks, Vessels, Pipelines for hot water, brine, crude oil.As a primer coat in a specific painting system

As a primer, intermediate, Top coat (Self priming) system for general immersion services up to 90C (Aramco APCS 2A)As a primer. Intermediate, Top Coat (Self priming) system For Portable water immersion services up to 90C (Aramco APCS 2B)As a primer. Intermediate, Top Coat (Self priming) system for general immersion services up to 120C (Aramco APCS 2c)As external coating 3 layer system for insulated carbon steel tank, vessels, Heat exchangers, valves, piping (Aramco APCS 2A, 2C Instead of APCS 2I, 2H)Can be used as a primer and intermediate followed by adiabatic polyurethane top coat under insulation of carbon steel for the external surfaces of saddle parts at surface temperature 49-100C. (NCP- I PAINT SYSTEM)

6) EPOXY/AMINE ADDUCT COATING SYSTEMMaximum Service Temperature: 90CSelf priming.Can be used for tank lining (interior) for immersion services.Can be used for interior coating of aviation fuel, turbine fuel, kerosene storage tank and piping. (Aramco APCS 2D)

7) AMINE ADDUCT SOLVANT FREE EPOXY PHENOLIC COATING SYSTEM (SELF PRIMING)Maximum Service Temperature: 93CCan be used for Immersion service such as hydrocarbon, aqueous and corrosive chemical environments.Relavant Aramco System :APCS 2E

8) GLASS FLAKE POLYESTER COATING (SELF PRIMING)Maximum Service Temperature : 100CSuitable for general immersion services.Immersion service such as hydrocarbon, seawater, raw water, aqueous and corrosive chemical environments.Not suitable for demineralised water and polar solvents

High thickness coating 600-1000 microns.Relavant Aramco System: APCS 2F

9) GLASS FLAKE VINYL ESTER COATING SYSTEM FOR HEAVY(SELF PRIMING)Maximum Service Temperature: 105CFor Heavy-Duty Immersion ServiceNot suitable for demineralised water and polar solventsTwo Component paint SystemCold cured vinyl ester/acrylic copolymerReinforced with glass flakes.Can be achieved high thickness unto 600-1000micronsImmersion service such as hydrocarbon, seawater, raw water, aqueous and corrosive chemical environments.Suitable for immersion service at GOSPS pressure vessels and headers.As a lining in immersed environments where superior resistance to chemical attack is required.Suitable for chemical resistant for PH values0-13Exellent resistant to deminaralised water and range of solvent.Suitable for aggressive atmospheric and spillage conditionsRelevant Aramco System: APCS 2G

10) 100% SOLID, GLASS FLAKE EPOXY COATINGFOR IMMERSSION SERVICES UP TO 105C

Maximum Service Temperature: 105CTypical UseCan be used for insulated and non insulated carbon steel.Immersion service such as hydrocarbon, aqueous and corrosive chemical environments.Very High thickness coating 750-1000 micronsA solvent free, two component polycyclamine cured lining system utilising advanced epoxy novolac technology with flake and fiber reinforcement.Excellent chemical and solvent resistance- High temperature immersion resistance (eg crude up to 194F (90C))- Fast cure (rapid return to service in 14 hours at 77F (25C))- Thermal and mechanical shock resistance- Ultra low VOC- Single coat application up to 80 mils (2000 microns)- Cathodic Disbondment resistance- Excellent abrasion and impact resistanceApplications include steel and concrete lining in the oil and gas, chemical, mining and water industries on assetssuch as crude and petroleum bulk storage tanks, downhole tubulars, downhole casing exteriors, interior and exteriorpipes, floors, tank pads, trenches, troughs, sumps and pits.Using Enviroline 376F-60 in conjunction with API 653 inspection and API 652 guidelines as a thick film reinforcedlining allows internal inspection intervals to be set at the maximum time allowable; potentially 20 years.Relevant Aramco Paint system: APCS 2H11) Ceramic/Inorganic Filled Epoxy-Phenolic/NovolacCoating for Immersion Service up to 150CMaximum Service Temperature: 150CTypical UseGOSP Traps, Plant Piping and fitting, Girth Weld for Water InjectionCan be used for insulated and non insulated carbon steel.Also can be used for stainless steel.High Thickness CoatingSpecial hot airless spray equipment needed.Excellent corrosion resistant at high temperatureResistant to abroad range of aqueous solution, hydrocarbon andprocess chemicals Specially suitable for condensate return tank, evaporators, heat exchanger barrels , oil-gas, oil-water separators , autoclaves, scrapper units, calorifiers, distillation units12) COAL TAR EPOXY PRIMERHigh Solid, high biuild polyamide cured coal tar epoxy coating.Maximum Service Temperature (Immersion): 70CNot for use in pressure vesselsNot suitable for use in direct sunlight.Typical UseImmersion service in tanks containing hydrocarbons, seawater, fresh water and most alkalis; intermittent contact with acids and solvents.As a long-life protection coating on steel and concrete in severe corrosive enviorenment.

It is also for buried concrete foundations and oily water concrete sumpsExcellent resistant to sea water, cruid oil, various soil chemical and soil stress.Relecent Aramco system: APCS 3

13) ZINC PHOSPHATE ALKYYD PRIMER COATINGSYSTEMMaximum Service Temperature: 120CQuick-dryingBased on oil alkyd or urethane alkydSuitable for mild to medium corrosive atmosphere.Typical UseStructural steelwork, tanks, vessels, pipes and equipment subject to moderate industrial atmospheres including H2S fumes and high humidity.Not generally recommended for shop applications or when handling is required after coating.As a primer for oleo resinous general purpose aluminum paint top coat. (Aramco APCS 4)As a primer for alkyd enamel paint system top coat (Aramco APCS 6)

14) RADIANT HEAT INSULATING COATING SYSTEM.Maximum Service Temperature: 350F (177C)Typical UseExternal top-coating system for petroleum tanks, vessels and drums to reduce the solar heat gain and to minimize the evaporation losses. It can be used on cooling water piping, gas and crude piping to reduce the solar heat gain and temperature riseUsed over an approved primer of Inorganic zinc primer(APCS-1A) or poly amide adduct cured epoxy (APCS-1B) or Zinc rich epoxy primer(APCS-1C). A clear top coat of acrylic or polyurethane based coating may be applied over the insulating coating.Approved aliphatic polyurethane can be used for color coding.Relevant Aramco System : APCS 5A and Approved product Carbotherm3300( A carboline Product)Generic Type Waterborne AcrylicDescription Carbotherm 3300 is a ceramic blend insulativecomposite coating formulated in a hightemperature resistant acrylic binder. It is ideallysuited as a protective heat barrier to shieldpersonnel from hot surfaces. It also inhibits heattransfer into or out of a structure. Its insulativeproperties keeps structures exposed to solarradiation, significantly cooler. It can be used tominimize or eliminate sweating of pipes or otheroperating equipment.Features Excellent thin-film thermal insulation Superior crush strength (during application) Protects personnel from hot surfaces Multi-purpose interior/exterior coating Insulation provides anti-condensationProperties Easy to use Zero VOC; low odor May be applied on hot surfaces

15) HOT INSULATING COATING SYSTEMMaximum Service Temperature: 500F (260C)Can be used for carbon steel and stainless steel serviceTypical UseAlternative to conventional bulk insulations for energy conservation in hot services. Used for personal protection on hot pipingUsed with an approved primer of APCS-1A, APCS-1B or APCS-1C. A clear top coat of acrylic may be applied over the insulating coating. Additionally, water-borne aliphatic polyurethane can be used for color coding.Relevant Aramco System: APCS 5A and Approved product Carbotherm3300 (A carboline Product)Generic Type Waterborne AcrylicDescription Carbotherm 3300 is a ceramic blend insulativeComposite coating formulated in a highTemperature resistant acrylic binder. It is ideallySuited as a protective heat barrier to shieldPersonnel from hot surfaces. It also inhibits heattransfer into or out of a structure. Its insulativeproperties keeps structures exposed to solarradiation, significantly cooler. It can be used tominimize or eliminate sweating of pipes or otherOperating equipment.Features excellent thin-film thermal insulationSuperior crush strength (during application) Protects personnel from hot surfaces Multi-purpose interior/exterior coating Insulation provides anti-condensationproperties Easy to use Zero VOC; low odor May be applied on hot surface

16) CHLORINATED RUBBER COATINGSYSTEM( SELF PRIMING)Maximum Service Temperature: 60CHigh Build paintResistant to salt water, splashes of mineral oils, aliphatic solvent and a wide range of chemicalNot suitable for aromatic solvent or animal, vegetable oils.Selfprimer or intermediate or top coat on steel structures in moderately to severely corrosive environment including permanently submerged surfaces.Typical UseMetallic and concrete surfaces exposed to salts, high humidity, and spillage of acids and alkalis.

17) BITUMINOUS PAINT SYSTEM( SELF PRIMING)For moderate temperature, Buried and immersion ServicesMaximum Service temperature: 60CTypical UseBuried and immersed steel. Resistant to water and acidic fumes. Not generally recommended for shop applications or when handling is required after coatingHigh BuildFlexibleWater ResistantRust PreventingAs an economical corrosion protection of interior and exterior steel and concrete substrates in moderately corrosive environmentNot exposed to direct sunlightWell suited for steel and concrete surfaces buried in sub soil conditions.Relevant Aramco SYSTEM: APCS 10, APCS 2318) SILICON ALUMINIUM VERY HIGH TEMPERATURE COATING SYSTEM ( SELF PRIMING)Heat resistant aluminum pigmented polysiloxane paintService Temperature: 600CCarbon Steel Surfaces in atmospheric conditionFor long term protection of hot pipe lines, exhaust pipes, smoke stakes and other hot surfacesLow DFTCan be used as a self priming 2coat system temperature 400-540c (Aramco APCS11B) for carbon steel surfaces atmospheric condition.Can be used as a top coat for the inorganic zinc primer in a temperature 150-400c (Aramco APCS 11A)19) AIR DRYING, SINGLE COMPONENT, HIGH HEAT EXTERNAL COATING FOR BARE AND INSULATED CARBON STEEL AND AUSTENITIC STAINLESS STEEL.Self PrimingMaximum Service Temperature: -320F-1500FUses: Protective Coating from Pitting Corrosion and Stress Corrosion cracking for bare and insulated Austenitic 300 Series Stainless SteelCan be used ultra high service temperature for carbon steel-Above 540CCan be used for insulated carbon steel.Can be used for stainless steelCan be used for insulated stainless steel.It is capable of providing corrosion protection to steel in both atmospheric service and under thermal insulation operating in thermal cyclical conditions between to -20F(-29C) up to 752F (400C) without the need for additional heat curing, prior to being placed in service.

Relevant Aramco system: APCS 11C20) HAND APPLIED SPLASH ZONE COMPOUNDA Solvent free polyamide cured epoxy paintMaximum Service Temperature: 80CNot suitable for use in contact with potable water

Ultra high thickness paint system 2500 micronsA Tough and Hard coating with high resistant to abrasion water, aliphatic solvent, vegetable and mineral oilsTemporary maintenance coating on boat landings and non-critical steel surfaces in splash zone or immersion service. Patch repairs to APCS - 19A and APCS - 19B.As a hand applied repair compound for splash zone area on offshore platforms, jetties, sheet pilings and buried steel work which is exposed highly corrosive environments.For spot repair in cargo tanks and ballast tanks, including pitted areas.Relevant Aramco Standard: APCS 19A21) SPRAY APPLIED SPLASH ZONE COMPOUNDA solvent free two component epoxy coating.Maximum Service Temperature: 40CNot suitable for use in contact with potable water.A hard, tough and well adhering protective coating with excellent resistance to abrasion and water (sea)High Thickness Coating 2500 microns.Typical UseCertain steel surfaces in splash zone areas of marine structures such as offshore platforms, jetties, and steel pilings.Also, as a pipe coating at above/below ground transitions and road crossings.As a heavy duty coating on steel and concrete surfaces exposed to severe corrosive conditions and /or impact. Such as (helicopter decks and splash zone areas of offshore platforms, drilling rigs, jetties, piers and sheet pilingsRelevelant Aramco system: APCS19B22) GLASS FLAKE REINFORCED AMINE ADDUCT CURED EPOXY COATING SYSTEMMaximum Service Temperature: 93CNot suitable for Hot Risers in Splash ZoneSuitable for new construction and rehabilitation of existing Structural Steel membersTypical Use: Corrosion protection for all offshore and marine structural steel members at splash zone and atmospheric exposure. Suitable for jetties, pilings, and pipe at above/below ground transition areas.High thickness coating 1000 microns.It is hard and tough coating with excellent resistant to abrasion, sea water mineral oils, alipahatic hydrocarbons and splashes from petrol and related products.Suitable for early water exposure and will continue to cure under water.As a self primed high build coating primarily for areas subject to abrasion and/or to a highly corrosive environment.Examples: Splash zone, jetty piling, and working decks.Can be used as interior lining for crude oil and fuel oil water.Short pot life.Susceptible for Orange peel,Relevant Aramco system: APCS 19C

23) POLY AMINE CURE EPOXY PAINT FOR DAMP SURFACES-TWO COAT SYSTEMTwo coat systemHigh build, two componentsGood wetting propertyExcellent resistant to seawater and crude oilSelf primingCan be used as a repair and maintenance coating for ballast tanks and void spacesSuitable for application below 0CEpoxy Coating for Application onto Damp Steel Surfaces; Two-Coat SystemMaximum Service Temperature: 150CNot normally suitable for immersion serviceTypical UseOffshore Steel Structures in above-water areas. Can be applied in conditions of high humidity to a slightly damp substrate.Relevent Aramco system APCS 22A

24) MODIFIED EPOXY BARRIER COAT FOR DAMP SURFACES-SINGLE COATA two componentLow VOCHigh solidProvide long term protection in a single coat application.Will continue to cure when immersed in water.Excellent cathodic disbondment resistant.Epoxy Coating for Application onto Damp Steel Surfaces; One-Coat SystemMaximum Service Temperature: 150CNot normally suitable for immersion serviceTypical UseOffshore Steel Structures in above-water areas. Can be applied in conditions of high humidity to a slightly damp substrate.Primarily design for off shore splash zone maintenance where its continued cure under immersed condition makes it ideal for coping with tidal movements and surges.May be applied to deoxidized and slightly damp surfaces.Can be used corrosive environments including pulp and paper plants, chemical plants, jetties and sluice gateCan be used as a part of a non slip deck system in conjunction with appropriate aggregate.Related Aramco system: APCS 22B

25) HIGH TEMPERATURE MASTIC PAINT FOR BURRIED OR IMMERSION SERVICES (SELFPRIMING)PHYSICALLY DRYING HIGH BUILD BITUMINOUS SYSTEMMaximum Service Temperature: 95C.Not suitable for exposure to sunlight or hydrocarbonsTypical UseBuried steel pipe, tanks and structures.Typical UseBuried and immersed steel. Resistant to water and acidic fumes. Not generally recommended for shop applications or when handling is required after coatingHigh BuildFlexibleWater ResistantRust PreventingAs an economical corrosion protection of interior and exterior steel and concrete substrates in moderately corrosive environmentNot exposed to direct sunlightWell suited for steel and concrete surfaces buried in sub soil conditions.Relevant Aramco SYSTEM: APCS 10, APCS 23

26) POLYAMIDE ADDUCT CURED EPOXY PAINTA Primer-Intermediate- Top coat Paint.Two component, High build, High solid paint.Maximum service temperature: 120CHard and Tough coatGood wetting propertiesLow temperature curingCan be used as a self primed surface tolerant paint system.(APCS26)Can be used as a primer for polyurethane top coat (APCS 26T)Can be used as Top coat for inorganic zinc primer (APCS 1A)Can be used as Top coat for polyamide cured epoxy primer (APCS 1B)Can be used as Top coat for Zinc rich epoxy primer (APCS 1C)Can be used as a Intermediate coat for inorganic zinc primer and polyurethane top coat.(APCS 1D)Can be used as a Intermediate coat for polyamide cured epoxy primer and polyurethane top coat.(APCS 1E)Can be used as a Intermediate coat for zinc rich epoxy prime and polyurethane top coat.(APCS 1F)Can be used a non skid epoxy paint for non skid floors and deck with proper use of Aggregate. (APCS12)HEMPEL PAINT: HEMPADUR MASTIC 45881/45880

27) SOLVANT FREE TWO ULTRA HYBRID EPOXY COATING SYSTEM FOR IMMERSION SERVICESEpoxy-Phenol Novolac Coating-Solvent free two component systemMaximum Service Temperature: 150CService limitation: Not suitable for potable water services.Typical use: Immersion service for GOSP vessels handling hydrocarbon solutions at temperature up to 150C. Suitable for immersion in DGA (Di-Glycol Amine) columns, Sulphur recovery units, sour gas treating unitsDesigned to resist water, hydrocarbons, aqueous solution and pressurized steam up to temperature 180c.Excellent erosion, corrosion resistant at elevated temperature thorough a binary curing mechanism.High Thickness coating system 600-1000 MicronsRelevant Aramco System: APCS 27BELZONA PRODUCT: Belzona 1591 (formerly Ceramic XHT)

28) Specialty Liquid Coating Systems for Pumps, Valves, Piping, Fitting and Exchanger Boxes.Service Condition: Suitable up to 105C.Typical Use: Suitable for new and existing pump casing valves and piping in immersion seawater and hydrocarbon services where good corrosion, abrasion, and chemical resistance are required.Relevant Aramco Coating System: APCS28APPROVED PRODUCTS:1- Ceramic/Alloy Filled Epoxy CoatingsFiller Coatings:Belzonas 1311/1111ARC-858, ARC-10Barrier Coatings:Belzonas 1341/1321/1391S/1391T /5891ARC-855 HTST, ARC-S22- Glass Flakes Filled CoatingsFiller Coatings:Corroglass 100, Corroglass 200, Corroglass 600, Polyglass VEFBarrier Coatings & Top Coat:Fluiglide and/or Veil cote

29) AMINE ADDUCT CURED EPOXY COATING (SELF PRIMING)External surface of steel pipe only.High build and high solid paint.Can be used in severely corrosion environment such as buried pipe lines in wet ground.Maximum Service Temperature: 90cVery hardHigh impact and abrasion resistanceAs new construction as well as repaired and renovation coatingNeed heavy duty airless spray machineRelevant Aramco System: APCS 113AHEMPLE PRODUCT: HEMPADUR XP 87550

30) RUST CONVERSION PRIMER

PAINT SYSTEMEPOXY COATING SYTEM WITH INORGANIC ZINC PRIME(APCS 1A)PRIMER: INORGANIC ZINC PRIMER (INORGANIC ZINC SILICATE)TOP COAT: EPOXY TOP COAT (POLYAMIDE ADDUCTS CURED EPOXY)EPOXY COATING SYSTEM WITH EPOXY PRIMER(APCS1B)PRIMER: EPOXY PRIMER (POLYAMIDE CURED EPOXY PRIMER)TOP COAT: EPOXY TOPCOAT (POLYAMIDE ADDCUT CURED EPOXY)EPOXY COATING SYSTEM WITH ZINCRICH EPOXY PRIMER (APCS1C)PRIMER: ZINC RICH PRIMERTOP COAT: EPOXY TOPCOAT (POLYAMIDE ADDUCTS CURED EPOXY)EPOXY/POLYURETHANE TOPCOAT WITH IOZ PRIMER (APCS1D ) PRIMER: INORGANIC ZINC PRIMER (INORGANIC ZINC SILICATE)INTERMEDIATE: POLYAMIDE ADDUCT CURRED EPOXYTOP COAT: POLYURETHANEEPOXY/POLYURETHANE TOPCOAT WITH EPOXY PRIMER (APCS 1E)PRIMER: POLYAMIDE CURRED EPOXY PRIMERINTERMEDIATE: POLYAMIDE ADDUCT CURRED EPOXYTOPCOAT : POLYURETHANE EPOXY/POLYURETHANE TOPCOAT WITH ZINC RICH EPOXY PRIMER (APCS1F)PRIMER : ZINC RICH PRIMERINTERMEDIATE: POLYAMIDE ADDCUTCURRED EPOXYTOPCOAT: POLYURETHANEEPOXY COATING SYSTEM FOR GENERAL IMMERSION SERVICESUP TO 90C (APCS2A )PRIMER: PHENOLIC EPOXYINTERMEDIATE: PHENOLIC EPOXYTOPCOAT: PHENOLIC EPOXYEPOXY COATING SYSTEM FOR PORTABLE WATER IMMERSION SERVICES SELFPRIMING (APCS2B) UP TO 90CPRIMER: AMINE ADDUCT SOLVANT FREE EPOXYINTERMEDIATE: AMINE ADDUCT SOLVANT FREE EPOXYTOPCOAT: AMINE ADDUCT SOLVANT FREE EPOXYAPCS2C EPOXY COATING SYSTEM FOR IMMERSION SERVICES UP TO 120C(APCS2C)PRIMER: PHENOLIC EPOXYINTERMEDIATE: PHENOLIC EPOXYTOPCOAT: PHENOLIC EPOXYEPOXY COATING SYSTEM FOR THE INTERIOR OF AVIATION FUEL STORAGE TANKS UP TO 90C(APCS2D)PRIMER: AMINE ADDUCT CURED EPOXYTOPCAOT: AMINE ADDUCT CURED EPOXYSOLVENT FREE PHENOLIC EPOXY COATING SYSTEM FOR GENERAL IMMERSION SERVICE UP TO 93C(APCS2E)PRIMER: SOLVANT FREE EPOXY PHENOLICGLASS FLAKE REINFORCED POLYESTER COATIN FOR GENERAL IMMERSION SERVICES UPTO 100C (APCS2F)PRIMER: GLASS FLAKE POLYSTER GLASS FLAKE REINFORCED POLY VINYLESTER COATING SYSTEM UPTO 105C (APCS2G)PRIMER: GLASS FLAKE VINYL ESTER100% SOLID GLASSFLAKE EPOXY COATING SYSTEM FOR IMMERSION SERVICES UPTO 105C (APCS2H)PRIMER: GLASS FLAKE EPOXYCERAMIC/NOVOLAC FILLED EPOXY-PHENOLIC/NOVOLAC COATING SYSTEM UPTO 150C (APCS2I)PRIMER: CERAMIC/ INORGANIC FILLED PHENOLIC/NOVOLACCOAL TAR EPOXY COATING SYSTEM FOR IMMERSION OR BURRIED STEEL AND CONCRETE SURFACE UP TO 70C(APCS3)PRIMER: COAL TAR EPOXYTOP CAO: COAL TAR EPOXYALUMINIUM PIGMENTED ALKYED COATIN UP TO UP TO 80C(APCS4)PRIMER: ZINC PHOSPHATE ALKYYD PRIMERINTERMEDIATE: ZINC PHOSPHATE ALKYYD PRIMERTOPCOAT: GENERAL PURPOSE ALUMINUMRADIANT HEAT INSULATING COATING SYSTEM UP TO 177C(APCS5A)PRIMER: INORGANIC ZINC SILICATE OR POLYAMIDE CURED EPOXY OR ZINC RICH EPOXYTOPCOAT: RADIANT HEAT INSULATING CLEAR PAINTHOT INSULATING COATING SYSTEM FOR C.S AND SS UP TO 260C (APCS5B)PRIMER: HOT INSULATING COATING SYSTEMALKYD ENAMAL COATING SYSTEM (APCS6) UP TO 70CPRIMER: ZINC PHOSPHATE ALKYYD PRIMERINTERMEDIATE: ZINC PHOSPHATE ALKYYD PRIMERTOPCOAT: ALKYED ENAMALRUST CONVERSION PRIMER/ALKYD TOP COAT SYSTEM FOR SLIGHTLY RUSTED STEEL SURFACES UP TO 70C(APCS7)PRIMER: RUST CONVERSION PRIMERTOPCOAT: ALKYED ENAMAL OR ALUMINIUM ALKYED

CHLORINATED RUBBER COATING SYSTEM UP TO 60C APCS9)PRIMER: CHLORINATED RUBBERTOPCOAT: CHLORINATED RUBBERBITUMINOUS COATING SYSTEM FOR MODERATE TEMPERATURE FOR BURRIED AND IMMERSION SERVICES UPTO 60C (APCS10)PRIMER: BITUMINOUSINTERMEDIATE: BITUMINOUSTOP COAT: BITUMINOUSHIGH TEMPERATURE COATING SYSTEM FOR ATMOSPERIC SERVICES BETWEEN150 400C WITH IOZ PRIMER (APCS 11A)PRIMER: INORGANIC ZINC SILICATETOP CAT : SILICON ALUMINIUMVERY HIGH TEMPERATURE COATING SYSTEM FOR ATMOSPERIC SERVICES BETWEEN400-540C (APCS 11B)PRIMER: SILICON ALUMINIUMTOPCOAT : SILICON ALUMINIUMAIR DRYING,SINGLE COMPONET, HIGH HEAT EXTERNAL COATING SYSTEM FOR BARE AND INSULATED CS AND AUSTENITIC SS BETWEEN -196C TO 815C (APCS11C)PRIMER: NOVEL HIGH PERFORMANCE ANTI-CORROSIVE PAINTNON SKID EPOXY COATING SYSTEM FOR FLOOR AND DESK UP TO 150C(APCS12)PRIMER: POLYAMIDE CURRED EPOXYINTERMEDIATE: POLYAMIDE ADDUCT CURRED EPOXYNONSKID AGGRE-IGATETOP COAT: POLYAMIDE ADDUCT CURED EPOXYINORGANIC ZINC PRIMER SOLVANT BASED UPTO 400C(APCS17A)PRIMER: INORGANIC ZINC PRIMER (SILICATE) SOLVANT BASED

INORGANIC ZINC PRIMER- WATER BASED UP TO 400C(APCS17B)PRIMER: INORGANIC ZINC PRIMER (SILICATE) WATER BASEDSPLASH ZONE COMPOUND-HAND APPLIED UP TO 80C(APCS19A)PRIMER: SPLASH ZONE COMPOUND HAND APPLIEDSPLASH ZONE COMPOUND SPRAY APPLIED UP TO 80C(APCS19B)PRIMER: SPLASH ZONE COMPOUND SPRAY APPLIEDGLASS FKAKE REINFORCED POLYESTER/EPOXY FOR OFF SHORE STRUCTURAL STEEL UP TO93C(APCS19C)PRIMER: GLASS FLAKE REINFORCED POLYESTER.TOPCOAT: GLASS FLAKE REINFORCED POLYESTER.FIBRE GLASS REINFORCED EPOXY COATING SYSTEM HAND APPLIED(APCS20A)PRIMER: RESIN:FIBERGLASS MATERIAL: FIBREGLASS REINFORCED EPOXY-HAND APPLIEDAPCS20BPRIMER: RESIN:FIBERGLASS MATERIAL: FIBREGLASS REINFORCED EPOXY-SPRAY APPLIEDEPOXY COATING SYSETM FOR THE APPLICATION OF DAMP SURFACES UP TO 150C (APCS22A)-TWO COAT SYSTEMPRIMER: POLY AMINE CURE EPOXY PAINTTOPCOAT: POLY AMINE CURE EPOXY PAINTEPOXY COATING SYSETM FOR THE APPLICATION OF DAMP SURFACES UP TO 150C (APCS22B)-SINGLE COAT SYSTEMPRIMER: MODIFIED EPOXY BARRIER COATHIGH TEMPERATURE MASTIC COATING SYSTEM FOR BURRIED AND IMMERSION SERVICES UP TO 95C (APCS23)PRIMER: HIGH TEMPERATURE MASTIC/ BITUMINUOSEPOXY MASTIC COATING SYSTEM UPTO 120C(APCS26)PRIMER: POLYAMIDE ADDUCT CURED EPOXYTOPCOAT: POLYAMIDE ADDUCT CURED EPOXYEPOXY MASTIC COATING SYSTEM WITH POLYURETHANE TOP COAT FOR USE OUTDOORS WHEN ADDED GLOSS RETENSION, COLOUR RETENTIONAND ABRASION RESISTENT WHEN REQUIRED UP TO 80C (APCS26T)PRIMER: POLYAMIDE ADDUCT CURED EPOXYINTERMEDIATE: POLYAMIDE ADDUCT CURED EPOXYTOPCOAT: POLYURETHANESOLVENT FREE TWO COMPONENT ULTRA HYBRID COATING SYSTEM FOR IMMERSION SERVICES UPTO 150(APCS27)PRIMER: SOLVENT FREE ULTRA HYBRID EPOXYSPECIALITY COATING SYSTEM FOR PUMPS, VALVES,PIPINGS, FITTINGS,EXCHANGER BOXES(APCS28) UP TO 105CPRIMER:FILLER:TOPCOAT: