pabx with caller id

PABX with Caller IDPABX with Caller ID

MS48CMS48C

MS48CMS48C is is now ready now ready for for exportsexports!!!!!!

• Ergonomic Design in Plastic Cabinet

• Caller ID Detection

• SMS Transmission

MS48C - PABX with Caller IDMS48C - PABX with Caller ID

• Allows sending / receiving SMS through standard extensions as an option.

• Detects and displays Caller ID on standard extensions equipped with Caller ID sets as an option.

• Supports all add-ons / features of MS48S (except for ID12).

• Holds battery switch which is accessible without opening the cover.

• BT104BT104 Caller ID Telephone is an appropriate choice for New MS48C (with Caller ID) as a Low End Keyphone.Low End Keyphone.


Caller ID (CLID) & SMS can be integrated via EXP48C-CLID card. This card is to be installed on top of the motherboard if there are no expansion modules or on the lastly installed expansion module otherwise.


N.C. – Used N.C. – Used for for Firmware Firmware Changes Changes

N.C. – Used N.C. – Used for for DebuggingDebugging

KTS Input of KTS Input of CLID ModuleCLID Module

KTS Output KTS Output to Consolesto Consoles

• The expansion modules of MS48C are called EXP48C. • EXP48S expansion modules of MS48S can also be used with MS48C. But CLID is not supported on the lines and extensions of EXP48S modules.


No need to make separate grounding for EXP48C Expansion Modules. EXP48C is grounded once it is installed on the motherboard through a ground pin on the motherboard.


All ground cables are All ground cables are collected at this point. collected at this point. MS48C should be MS48C should be grounded from this grounded from this ground terminal.ground terminal.

Ground Pin for EXP48CGround Pin for EXP48C

Extension / line connectors allow vertical cabling. The position of connectors has been changed from horizontal to vertical.


CABLE CABLE HOLEHOLE

CABLE CABLE CHANNELCHANNELSS

CONNECTOCONNECTORSRS

12V- 7Ah battery can be located under the battery belt inside the cabinet.


BATTERY BATTERY CONNECTIOCONNECTIONN

BATTERY BATTERY BELTBELT


SPS48 Power Card with transformers are surrounded by portable plastic casing.

PRES

PRES

SS

SLID

SLID

EE


HOW TO OPEN THE CABINET


HOW TO ACCESS POWER & BATTERY SWITCHES

POWER SWITCHPOWER SWITCH

BATTERY SWITCHBATTERY SWITCH


HOW TO MOUNT MS48C ON THE WALL

• Drive the screws to Drive the screws to the wallthe wall

•Hook the system on Hook the system on the screw through the screw through the peer holesthe peer holes

•Fix the third screw Fix the third screw to the wallto the wall

• MS48C detects Caller ID in FSK or DTMF through C.O. Lines.

• MS48C sends Caller ID in FSK to standard extensions.• Caller ID can be displayed on standard CLID

telephones with feed voltage not higher than 24V. • Line impedance is 900/1800 Ohm, complex

impedance.


• The dimensions and weight of MS48S and MS48C are different from each other.

• Dimensions of MS48C are 39 cm x 13 cm (h) x 48 cm and its weight is 5 kg

• Dimensions of MS48S were 38 cm x 11 cm (h) x 43 cm and its weight is 8.25 kg

• With the launch of MS48C, MS48S is now obsolete. The motherboard, expansion modules and accessories of MS48S will continue to be available as spare parts only.


Technical SpecificationsTechnical SpecificationsBasic Capacity 4/12

Expandable By 2/6, 4/12, 0/16Two boards can be installed on the basic capacity. Only one can be 2/6 or 0/16

Max. Capacity 48 Ports

Line Interface Loop Start with DP/DTMF Signalling

Extension Interface Station Loop 1200 Ohms Including Set

Power 230 VAC, 50 Hz; Optional. 12V Bat. Backup

Power Consumption 11W (Stand-by)

Environment 0 °C to 45 °C to 80% Humidity

Dimensions 39x13x48 cm

Weight 5 kg (Basic capacity without battery)


pabx with caller id

Documents

caller idms48c pabx

caller idhow

caller idallows

caller idno

caller idms48cms48c

caller id sets

expansion modules of

dimensions of ms48c