pa inspection guidelines

8/4/2019 PA Inspection Guidelines

http://slidepdf.com/reader/full/pa-inspection-guidelines 1/18

1 © Nokia Siemens Networks

PA Inspection GuidelinesFor

Single Site Acceptance



© Nokia Siemens NetworksFor internal use only!

Page 1PA Certificate

Page 1 will be filled byDCC team, just leaveit




Page 2Site Info & Google Earth Picture

Page 2 Contains dateof drive test, Site ID &Google picture




Page 2.aSite Info & Google Earth Picture

Date of drive test mustbe filled & can bechecked on logfilecreated date.

Sites in this Polygonplease refer to thelatest SDB. When thesite’s not on air yet just

leave it blank.




Page 2.bSite Info & Google Earth Picture

Put proporsional viewof google earth picturehere.

This picture mustshown the PA site & its

surrounding neighbor(at least the firs tier)




Page 3Coverage Prediction and RxLevel Comparison

Page 3 Containssingle site coverageprediction & Overlaycomparison Picture


http://slidepdf.com/reader/full/pa-inspection-guidelines 7/18 © Nokia Siemens NetworksFor internal use only!

Page 3.aCoverage Prediction and RxLevel Comparison

Put proportional view ofCoverage Prediction

When generatingprediction, the ranges

& colors must set to PAdefault ranges




Page 3.bCoverage Prediction and RxLevel ComparisonThis is overlay betweencoverage prediction &RxLevel idle measresult.

All ranges must be as same as itused on covplot , so it comparable.

All ranges must be shown onlegend even when no data on it.

Also show Site ID & Site Name

Please be concerned on comparison :

Drive test result must as closed aspossible to the prediction

Check also the logfile in tems, makesure the partner not cheating

Use Tems Route Analysis to checkbinning validity




Page 4Idle RxLevel & RxQuality Plot

Page 4 Contains IdleRxLevel andRxQuality Plot




Page 4.aIdle RxLevel & RxQuality Plot

Put proportional viewof RxLevel Idle measresult

The plot must be assame as it shown on

overlay






Page 4.bIdle RxLevel & RxQuality Plot

Put proportional view ofRxQuality Plot

These are default ranges &colors for RxQuality Plot






Page 5Idle CI Plot & SQI Plot

Page 5 Contains IdleCI Plot & SQI Plot




Put proportional view of IdleCI Plot

Colors For PA site, Sect1 CIis Red, Sec2 CI is Yellow &Sect3 CI is Green

Make sure there’s no swap

sectorMake sure that all sectorsserve on its beam correctly.

Fix CI Colors only for PA site.


Page 5.aIdle CI Plot & SQI Plot

Site picture must belabeled with CI foreach sector




Put proportional view of SQIPlot

Colors For PA site, Sect1 CIis Red, Sec2 CI is Yellow &Sect3 CI is Green

Make sure there’s no swap

sectorMake sure that all sectorsserve on its beam correctly.

Page 5.bIdle CI Plot & SQI Plot

These are default ranges &colors for SQI Plot






Page 6Drive test KPI & CI Samples Table

Page 5 Contains IdleCI Plot & SQI Plot




Make sure all KPI arereached

Cross check each value onReached Column from filesthat attach on this PA

Check also the FTP test,make sure it’s a moving test

around the site using 1 MB fileand all sectors are covered (

use tems to check) .

FTP test are applicationthroughput, not RLCthroughput

Page 6.aDrive test KPI & CI Samples Table

For SQI ;

For samples contain only Full Rate(EFR/AMRFR), KPI to reach is “

>=28,80% “

For samples contain only Half Rate(HR/AMRHR), KPI to reach is “ >=20,80%

For Mix samples, KPI to reach is “>=20,90%




All CI’s shown on plot

(page 5) must be listedin this table.

Make sure that PAsite has CI more than

200 samples eachsector.

Page 6.bDrive test KPI & CI Samples Table




Page 7 onwardDefect

Page 7 onward mayContains defect for

justification

pa inspection guidelines

Documents