p441

Page: 1Settings File ReportSubstation:File: 000.set

Printed on: 02/09/2014 15:41:47Model Number: P441?A1A6?C36?J

SYSTEM DATA00.01: Language: English00.02: Password:****00.04: Description: MiCOM00.05: Plant Reference: AREVA00.06: Model Number: P441?A1A6?C36?J00.08: Serial Number: 123456A00.09: Frequency: 50 Hz00.0A: Comms Level: 200.0B: Relay Address: 100.0C: Plant Status: 000000000000000000.0D: Control Status: 000000000000000000.0E: Active Group: 100.10: CB Trip/Close: No Operation00.11: Software Ref. 1: C5.000.20: Opto I/P Status: 0000000000.21: Relay Status 1: 0000000000000000.22: Alarm Status 1: 0000000000000000000000000000000000.40: Relay Status 1: 0000000000000000.50: Alarm Status 1: 0000000000000000000000000000000000.51: Alarm Status 2: 0000000000000000000000000000000000.52: Alarm Status 3: 0000000000000000000000000000000000.D0: Access Level: 200.D1: Password Control: 200.D2: Password Level 1: ****00.D3: Password Level 2: ****

CB CONTROL07.01: CB Control by: Disabled

DATE AND TIME08.01: Date/Time: 2008-01-25 14:15:15.3308.06: Battery Status: Healthy08.07: Battery Alarm: Enabled08.20: LocalTime Enable: Fixed08.21: LocalTime Offset: 0 min08.22: DST Enable: Enabled08.23: DST Offset: 60.00 min08.24: DST Start:Last08.25: DST Start Day: Sunday08.26: DST Start Month: March08.27: DST Start Mins: 60.00 min08.28: DST End: Last08.29: DST End Day: Sunday08.2A: DST End Month: October08.2B: DST End Mins: 60.00 min

CONFIGURATION09.01: Restore Defaults: No Operation09.02: Setting Group: Select via Menu09.03: Active Settings: Group 109.04: Save Changes: No Operation09.05: Copy From: Group 109.06: Copy To: No Operation

MiCOM S1 Studio



09.07: Setting Group 1: Enabled09.08: Setting Group 2: Disabled09.09: Setting Group 3: Disabled09.0A: Setting Group 4: Disabled09.0D: Dist. Protection: Enabled09.10: Power-Swing: Enabled09.11: Back-up I>: Disabled09.12: Neg Sequence O/C: Disabled09.13: Broken Conductor: Disabled09.14: Earth Fault PROT: Disabled09.15: Aided D.E.F: Disabled09.16: Volt Protection: Disabled09.17: CB Fail & I<: Disabled09.18: Supervision: Disabled09.1A: Thermal Overload: Disabled09.1D: Residual O/V NVD:Disabled09.24: Internal A/R: Disabled09.25: Input Labels: Visible09.26: Output Labels: Visible09.28: CT & VT Ratios: Visible09.29: Record Control: Visible09.2A: Disturb Recorder: Visible09.2B: Measure't Setup: Visible09.2C: Comms Settings: Visible09.2D: Commission Tests:Invisible09.2E: Setting Values: Secondary09.2F: Control Inputs: Visible09.35: Ctrl I/P Config: Visible09.36: Ctrl I/P Labels: Visible09.48: Ethernet NCIT: Visible

CT AND VT RATIOS0A.01: Main VT Primary: 110.0 V0A.02: Main VT Sec'y: 110.0 V0A.03: C/S VT Primary: 110.0 V0A.04: C/S VT Secondary: 110.0 V0A.07: Phase CT Primary: 600.0 A0A.08: Phase CT Sec'y: 5.000 A0A.0D: MComp CT Primary: 600.0 A0A.0E: MComp CT Sec'y: 5.000 A0A.0F: C/S Input:A-N0A.10: Main VT Location: Line0A.11: CT Polarity: Standard

RECORD CONTROL0B.04: Alarm Event: Enabled0B.05: Relay O/P Event: Enabled0B.06: Opto Input Event: Enabled0B.07: General Event: Enabled0B.08: Fault Rec Event: Enabled0B.09: Maint Rec Event: Enabled0B.0A: Protection Event: Enabled0B.30: Clear Dist Recs: No

MiCOM S1 Studio



0B.40: DDB 31 - 0: 111111111111111111111111111111110B.41: DDB 63 - 32: 111111111111111111111111111111110B.42: DDB 95 - 64: 111111111111111111111111111111110B.43: DDB 127 - 96: 111111111111111111111111111111110B.44: DDB 159 - 128: 111111111111111111111111111111110B.45: DDB 191 - 160: 111111111111111111111111111111110B.46: DDB 223 - 192: 111111111111111111111111111111110B.47: DDB 255 - 224: 111111111111111111111111111111110B.48: DDB 287 - 256: 111111111111111111111111111111110B.49: DDB 319 - 288: 111111111111111111111111111111110B.4A: DDB 351 - 320: 111111111111111111111111111111110B.4B: DDB 383 - 352: 111111111111111111111111111111110B.4C: DDB 415 - 384: 111111111111111111111111111111110B.4D: DDB 447 - 416: 111111111111111111111111111111110B.4E: DDB 479 - 448: 111111111111111111111111111111110B.4F: DDB 511 - 480: 111111111111111111111111111111110B.50: DDB 543 - 512: 111111111111111111111111111111110B.51: DDB 575 - 544: 111111111111111111111111111111110B.52: DDB 607 - 576: 111111111111111111111111111111110B.53: DDB 639 - 608: 111111111111111111111111111111110B.54: DDB 671 - 640: 111111111111111111111111111111110B.55: DDB 703 - 672: 111111111111111111111111111111110B.56: DDB 735 - 704: 111111111111111111111111111111110B.57: DDB 767 - 736: 111111111111111111111111111111110B.58: DDB 799 - 768: 111111111111111111111111111111110B.59: DDB 831 - 800: 111111111111111111111111111111110B.5A: DDB 863 - 832: 111111111111111111111111111111110B.5B: DDB 895 - 864: 111111111111111111111111111111110B.5C: DDB 927 - 896: 111111111111111111111111111111110B.5D: DDB 959 - 928: 111111111111111111111111111111110B.5E: DDB 991 - 960: 111111111111111111111111111111110B.5F: DDB 1023 - 992: 11111111111111111111111111111111

DISTURB RECORDER0C.01: Duration: 1.500 s0C.02: TriggerPosition: 33.30 %0C.03: TriggerMode: Single0C.04: AnalogChannel1: VA0C.05: AnalogChannel2: VB0C.06: AnalogChannel3: VC0C.07: AnalogChannel4: VN0C.08: AnalogChannel5: IA0C.09: AnalogChannel6: IB0C.0A: AnalogChannel7: IC0C.0B: AnalogChannel8: IN0C.0C: DigitalInput1: Any Start0C.0D: Input1Trigger: Trigger L/H0C.0E: DigitalInput2: Any Trip0C.0F: Input2Trigger: No trigger0C.10: DigitalInput3: DIST Trip A0C.11: Input3Trigger: No trigger0C.12: DigitalInput4: DIST Trip B

MiCOM S1 Studio



0C.13: Input4Trigger: No trigger0C.14: DigitalInput5: DIST Trip C0C.15: Input5Trigger: No trigger0C.16: DigitalInput6: DIST Fwd0C.17: Input6Trigger: No trigger0C.18: DigitalInput7: DIST Rev0C.19: Input7Trigger: No trigger0C.1A: DigitalInput8: Z10C.1B: Input8Trigger: No trigger0C.1C: DigitalInput9: Z20C.1D: Input9Trigger: No trigger0C.1E: DigitalInput10: Z30C.1F: Input10Trigger: No trigger0C.20: DigitalInput11: Z40C.21: Input11Trigger: No trigger0C.22: DigitalInput12: Any Pole Dead0C.23: Input12Trigger: No trigger0C.24: DigitalInput13: All Pole Dead0C.25: Input13Trigger: No trigger0C.26: DigitalInput14: SOTF Enable0C.27: Input14Trigger: No trigger0C.28: DigitalInput15: SOTF/TOR Trip0C.29: Input15Trigger: No trigger0C.2A: DigitalInput16: S. Swing Conf0C.2B: Input16Trigger: No trigger0C.2C: DigitalInput17: Out Of Step0C.2D: Input17Trigger: No trigger0C.2E: DigitalInput18: Out Of Step Conf0C.2F: Input18Trigger: No trigger0C.30: DigitalInput19: Man. Close CB0C.31: Input19Trigger: No trigger0C.32: DigitalInput20: I A/R Close0C.33: Input20Trigger: No trigger0C.34: DigitalInput21: DIST. Chan Recv0C.35: Input21Trigger: No trigger0C.36: DigitalInput22: MCB/VTS Main0C.37: Input22Trigger: No trigger0C.38: DigitalInput23: MCB/VTS Synchro0C.39: Input23Trigger: No trigger0C.3A: DigitalInput24: DEF. Chan Recv0C.3B: Input24Trigger: No trigger0C.3C: DigitalInput25: DEF Rev0C.3D: Input25Trigger: No trigger0C.3E: DigitalInput26: DEF Fwd0C.3F: Input26Trigger: No trigger0C.40: DigitalInput27: DEF Start A0C.41: Input27Trigger: No trigger0C.42: DigitalInput28: DEF Start B0C.43: Input28Trigger: No trigger0C.44: DigitalInput29: DEF Start C0C.45: Input29Trigger: No trigger

MiCOM S1 Studio



0C.46: DigitalInput30: Unused0C.48: DigitalInput31: Unused0C.4A: DigitalInput32: Unused

MEASURE'T SETUP0D.01: Default Display: Description0D.02: Local Values: Secondary0D.03: Remote Values: Primary0D.04: Measurement Ref: VA0D.05: Measurement Mode: 00D.06: Demand Interval: 30.00 min0D.07: Distance Unit: Kilometres0D.08: Fault Location: Distance

CB MONITOR SETUP10.01: Broken I^: 2.00010.02: I^ Maintenance: Alarms Disabled10.04: I^ Lockout: Alarms Disabled10.06: No CB Ops Maint: Alarms Disabled10.08: No CB Ops Lock: Alarms Disabled10.0A: CB Time Maint: Alarms Disabled10.0C: CB Time Lockout: Alarms Disabled10.0E: Fault Freq Lock: Alarms Disabled10.11: Lockout Reset: No10.12: Reset Lockout By: CB Close

OPTO CONFIG11.01: Global Nominal V: 24/27V11.50: Opto Filter Cntl: 11111111

CTRL I/P CONFIG13.01: Hotkey Enabled: 1111111111111111111111111111111113.10: Control Input 1: Latched13.11: Ctrl Command 1: SET/RESET13.14: Control Input 2: Latched13.15: Ctrl Command 2: SET/RESET13.18: Control Input 3: Latched13.19: Ctrl Command 3: SET/RESET13.1C: Control Input 4: Latched13.1D: Ctrl Command 4: SET/RESET13.20: Control Input 5: Latched13.21: Ctrl Command 5: SET/RESET13.24: Control Input 6: Latched13.25: Ctrl Command 6: SET/RESET13.28: Control Input 7: Latched13.29: Ctrl Command 7: SET/RESET13.2C: Control Input 8: Latched13.2D: Ctrl Command 8: SET/RESET13.30: Control Input 9: Latched13.31: Ctrl Command 9: SET/RESET13.34: Control Input 10: Latched13.35: Ctrl Command 10: SET/RESET13.38: Control Input 11: Latched13.39: Ctrl Command 11: SET/RESET13.3C: Control Input 12: Latched

MiCOM S1 Studio



13.3D: Ctrl Command 12: SET/RESET13.40: Control Input 13: Latched13.41: Ctrl Command 13: SET/RESET13.44: Control Input 14: Latched13.45: Ctrl Command 14: SET/RESET13.48: Control Input 15: Latched13.49: Ctrl Command 15: SET/RESET13.4C: Control Input 16: Latched13.4D: Ctrl Command 16: SET/RESET13.50: Control Input 17: Latched13.51: Ctrl Command 17: SET/RESET13.54: Control Input 18: Latched13.55: Ctrl Command 18: SET/RESET13.58: Control Input 19: Latched13.59: Ctrl Command 19: SET/RESET13.5C: Control Input 20: Latched13.5D: Ctrl Command 20: SET/RESET13.60: Control Input 21: Latched13.61: Ctrl Command 21: SET/RESET13.64: Control Input 22: Latched13.65: Ctrl Command 22: SET/RESET13.68: Control Input 23: Latched13.69: Ctrl Command 23: SET/RESET13.6C: Control Input 24: Latched13.6D: Ctrl Command 24: SET/RESET13.70: Control Input 25: Latched13.71: Ctrl Command 25: SET/RESET13.74: Control Input 26: Latched13.75: Ctrl Command 26: SET/RESET13.78: Control Input 27: Latched13.79: Ctrl Command 27: SET/RESET13.7C: Control Input 28: Latched13.7D: Ctrl Command 28: SET/RESET13.80: Control Input 29: Latched13.81: Ctrl Command 29: SET/RESET13.84: Control Input 30: Latched13.85: Ctrl Command 30: SET/RESET13.88: Control Input 31: Latched13.89: Ctrl Command 31: SET/RESET13.8C: Control Input 32: Latched13.8D: Ctrl Command 32: SET/RESET

ETHERNET NCIT18.01: Physical Link: Copper18.02: AntiAlias Filter: Disabled18.03: Merge Unit Delay: 0 s18.04: LN Arrangement: VL,IL,IN18.20: LN1 Name: Logical Node Line 118.30: Synchro Alarm: 00

CTRL I/P LABELS29.01: Control Input 1: Control Input 129.02: Control Input 2: Control Input 2

MiCOM S1 Studio



29.03: Control Input 3: Control Input 329.04: Control Input 4: Control Input 429.05: Control Input 5: Control Input 529.06: Control Input 6: Control Input 629.07: Control Input 7: Control Input 729.08: Control Input 8: Control Input 829.09: Control Input 9: Control Input 929.0A: Control Input 10: Control Input 1029.0B: Control Input 11: Control Input 1129.0C: Control Input 12: Control Input 1229.0D: Control Input 13: Control Input 1329.0E: Control Input 14: Control Input 1429.0F: Control Input 15: Control Input 1529.10: Control Input 16: Control Input 1629.11: Control Input 17: Control Input 1729.12: Control Input 18: Control Input 1829.13: Control Input 19: Control Input 1929.14: Control Input 20: Control Input 2029.15: Control Input 21: Control Input 2129.16: Control Input 22: Control Input 2229.17: Control Input 23: Control Input 2329.18: Control Input 24: Control Input 2429.19: Control Input 25: Control Input 2529.1A: Control Input 26: Control Input 2629.1B: Control Input 27: Control Input 2729.1C: Control Input 28: Control Input 2829.1D: Control Input 29: Control Input 2929.1E: Control Input 30: Control Input 3029.1F: Control Input 31: Control Input 3129.20: Control Input 32: Control Input 32

Group 1 GROUP 1 DISTANCE ELEMENT

30.01: GROUP 1 Line Setting:30.02: Line Length: 24.00 km30.04: Line Impedance: 2.264 Ohm ( 1.066 Ohm)30.05: Line Angle: 61.90 deg (j 1.997 Ohm)30.06: GROUP 1 Zone Setting:30.07: Zone Status: 01001130.08: kZ1 Res Comp: 580.0e-330.09: kZ1 Angle: 10.50 deg30.0A: Z1: 192.4 mOhm30.0B: Z1X: 3.000 Ohm30.0C: R1G: 560.0 mOhm30.0D: R1Ph: 360.0 mOhm30.0E: tZ1: 0 s30.0F: kZ2 Res Comp: 580.0e-330.10: kZ2 Angle: 10.50 deg30.11: Z2: 271.6 mOhm30.12: R2G: 720.0 mOhm30.13: R2Ph: 500.0 mOhm30.14: tZ2: 200.0 ms

MiCOM S1 Studio



30.15: kZ3/4 Res Comp: 580.0e-330.16: kZ3/4 Angle: 10.50 deg30.17: Z3: 340.0 mOhm30.18: R3G-R4G: 900.0 mOhm30.19: R3Ph-R4Ph: 600.0 mOhm30.1A: tZ3: 600.0 ms30.2B: GROUP 1 Other Parameters:30.2C: Serial Cmp. Line: Disabled30.2D: Overlap Z Mode: Disabled30.2E: Z1m Tilt Angle: 0 deg30.2F: Z1p Tilt Angle: 0 deg30.30: Z2/p/q Tilt Angl: 0 deg30.31: Fwd Z Chgt Delay: 30.00 ms30.32: V Mem Validity: 10.00 s30.33: Earth I Detect.: 50.00 mA30.34: GROUP 1 Fault Locator:

GROUP 1 DISTANCE SCHEMES31.01: Program Mode: Standard Scheme31.02: Standard Mode: Basic + Z1X31.03: Fault Type: Both enabled31.08: tReversal Guard: 20.00 ms31.09: Unblocking Logic: None31.0A: SOTF/TOR Mode: 10000010000000031.0B: SOTF Delay: 110.0 s31.0C: Z1Ext Fail: Disabled31.0D: GROUP 1 Weak Infeed:31.0E: WI:Mode Status: Disabled31.1B: GROUP 1 Loss Of Load:31.1C: LoL:Mode Status: Disabled31.1F: LoL:Window: 40.00 ms

GROUP 1 POWER-SWING32.01: Delta R: 180.0 mOhm32.02: Delta X: 180.0 mOhm32.03: IN> status: Enabled32.04: IN> (%Imax): 40.00 %32.05: I2> status: Enabled32.06: I2> (%Imax): 30.00 %32.07: ImaxLine> Status: Enabled32.08: ImaxLine >: 15.00 A32.09: Delta I Status: Enabled32.0A: Unblocking delay: 30.00 s32.0B: Blocking Zones: 11111132.0C: Out of Step: 132.0D: Stable Swing: 1

GROUP 1 INPUT LABELS4A.01: Opto Input 1: Opto Label 014A.02: Opto Input 2: Opto Label 024A.03: Opto Input 3: Opto Label 034A.04: Opto Input 4: Opto Label 044A.05: Opto Input 5: Opto Label 054A.06: Opto Input 6: Opto Label 06

MiCOM S1 Studio



4A.07: Opto Input 7: Opto Label 074A.08: Opto Input 8: Opto Label 08

GROUP 1 OUTPUT LABELS4B.01: Relay 1: Relay Label 014B.02: Relay 2: Relay Label 024B.03: Relay 3: Relay Label 034B.04: Relay 4: Relay Label 044B.05: Relay 5: Relay Label 054B.06: Relay 6: Relay Label 064B.07: Relay 7: Relay Label 074B.08: Relay 8: Relay Label 084B.09: Relay 9: Relay Label 094B.0A: Relay 10: Relay Label 104B.0B: Relay 11: Relay Label 114B.0C: Relay 12: Relay Label 124B.0D: Relay 13: Relay Label 134B.0E: Relay 14: Relay Label 14

MiCOM S1 Studio

p441

Documents