AkzoNobel

11%0-lux°

Micron®

P

y ac

htp

ain

t.co

m

PERCENT 28.45% MIX ONLY WITH MICRON OPTIMA

ACTIVATOR PART B (EPA Reg. No. 2693-194)

WHEN COMPONENTS MICRON OPTIMA - BASE PART A AND MICRON OPTIMA ACTIVATOR PART 13 ARE MIXED THE RESULTING PAINT IS CORROSIVE AND MAY CAUSE SEVERE EYE IRRITATION THAT COULD LEAD TO IRREVERSIBLE EYE DAMAGE. DO NOT GET IN EYES OR ON CLOTHING. WEAR PROTECTIVE EYE WEAR.

71.55% 100.00% 25.74%

ACTIVE INGREDIENT& CUPROUS OXIDE CAS #1317-39-1 INERT INGREDIENTS

COPPER AS METALLIC

EPA EST 2693-TX-1 EPA REG NO. 2693-193

Activated Biolux Technology Blocks Slime & Boosts Performance Ultimate Antifouling Performance in All Conditions

Self Polishing - No Buildup Puts An End to Mid-Season Scrubbing

KEEP OUT OF REACH OF CHILDREN

WARNING See Side Panel for Additional Precautionary Statements.

BASE PART A OF A TWO PART ANTIFOULING PAINT SYSTEM

NET CONTENTS: 0.875 GALLON (3.31 L)

2693-193_Micron Optima various colors_20150217_96_2693_.pdf

MICRON OPTIMA Base Part A of a Two Part Antifouling Paint System

PRODUCT DESCRIPTION: MICRON OPTIMA® oilers an entirely new development in antifouling paha technology:Ibis special Iwo-pack paint was formulated with an advanced activator biocide system that provides exceptional protection born all types of shell and weed fouling. MICRON OPITMA also uses MMus"e technology to control slime and algae growth. MICRON OPTIMA is a multi-season. sell polishing copolymer that washes away over time similar lea bar of scap.This results in reduced build up of old ooali nes and minimizes sanding at reapplication. This copolymer technology also allows the boat to be hauled and relaunched without recoatiog. MICRON OPTIMA is lop use below the waterline on fiberglass, wood and properly primed metal boat hulls and parts. Do not use on aluminium MICRON OPTIMA can be used in flesh, salt and brackish waters. Apply by brush and feller only, do nal spray. Wet sand only, do eat dry Sane. DIRECTIONS FOR USE his a violation of federal law to use this product in a manner Inconsistent will its labeling. MIXING RATIO: Poor to use of Kim product. we 7 parts by volume of Ibis product with lint of MICRON OPTIMA Activator (EPA Reg. No.2693-194 COMPATIBILITY: MICRON OPTIMA can be applied over most hard, conventional antifouling paints as long as the old coaling is tightly adhered, B in sound condition, and has been roughly sanded with 80 grit wet sandpaper. MICRON OPTIMA should not be applied over MICRON® 33, MICRON® 44 or soil antifouling paints. Those old coatings should be removed. V.O.C.: Less than 150 grams/liter. THINNING: Thin only when necessary. Do not exceed 109„ by volume. THINNER: Brushing - INTERLUXIM PARC CONDITIONER 6216. CLEAN-UP: INTERLUX Sr PAINT CONDITIONER 6216. Spraying Do not spray. INDUCTION TIME 5 minutes. THEORETICAL COVERAGE: 375 square It egallon.Yrelds 1.2 mils dry film thickness. APPLICATION TEMPERATURES: 501F (10°C) and above' (Air and Hull)

II either hull or air temperature falls below 50°F (1020) during the 16 hour dry lime extend tile dry lane to a mininmm of 48 hours. So not apply If the air feels damp or ft is raining. II it rains immediately after application allow to dry lora minimum of 24 hours (48 hours ha <50°F (10°C)) atter II has stepped raining, prior to launch or overcoat. APPLICATION SYSTEMS: MG only when ready to use. Stir the Antilouling base and the Activator Thoroughly prior to mixing the two components. Then pour the Activator Mao the Antifouling base, stifling continuously. Stir the two parts together well, prior te use. Failure to property mix Me two components will result in a streaky appearance ul the paint when appliedAller mixing Ill stand for 5 rrenutes.Apply at least two full coats (3 coals en bare wool) of MICRON OPTIMA by brush or high density loam roller. Foe recommend Mal a different color of MICRON OPTIMA be applied for the list coal of a multi-coat applicallorklltis will act as a signal coot that the other layers hove worn away and that it is time to apply more MICRON OPHMA). Keep in mind Mat the life of the paint is thee® related to the amount of pad applied. If during application the brush pulls or the roller drags, add small increments of INTERLUX0 PAINT CONDIEIONER 6216 to improve handling but do not add moil than 10% by volume. Certain areas of the hull experience taster polishing than The other areas. These areas include Me waterline. the leading edge of the keel. the rudder and the bow Mem is suggested that an additional coal of paint be applied lo Mese areas to insure that the MICRON OPTIMA does not wash away before the other areas of the bottom. Mix only as much MICRON OPTIMA as can he used within 2 hours. Important - before applying 1/100011 OPTIMA, all underwater metal fltings (except zinc anodes) should be coated WM Prnewash 353/354. thinned will 355 followed by a suflable primer, such as Interim 36080r 370 Aerosol. or KterPrfilect 2E00 following label application instructions. Include a 2" boundary of primer around those fittings before painting with MICRON OPTIMANtematively apply two coats of conventional solvent based antifouling paint on and around all under water reetalfetings and a 2" boundary around Me modes. Do not allow MICRON OPTIMA to come in contact with zinc anodes, PREVIOUSLY PAINTED SURFACES • Rood Condition: Remove all traces of loose paint and contamination by sanding the entire surface well with 80 grit wet sandpaper, raise surface clean using clean fresh wider and allow to dry 24 hours. Apply at least 2 coats 01 MICRON OPT IMA atlowing proper dry limes between mats,

PREVIOUSLY PAINTED SURFACES - Poor Condition: Completely remove all antifouling paint with INTERMIX® INTERSTRIP 299El or fiberglass, wood or by sandblasting steel surfaces to a near white metal. Proceed with application for bare work described below. BARE FIBERGLASS - Surface Preparation (Polyester or Vinylesler): It is very important Teat bare fiberglass be prepared properly to prevent delamination of antifouling pall Send) the surface thoroughly with soap and water using a slit bristled brush. Flush well wall fres water. tVhen the suttee° is dry, wipe a small area with a clean cloth that las been welled with INTERIM® FIBERGLASS SOLVENT WASH 02. While the solace® still wet remove with a clean My cloth, Repeat this process until the Who surface los been cleaned. To be certain N I all was and surface contaminants Nave been removed, run water over the surface. If the water beads up or separates, wipe again will FIBERGLASS SOLVENT WASH 202. When the water sheets off, all contamination has been removed. Sanding Macs not remove contamination. Ali r the surface has been properly cleaned, proceed with the application systems below. Repair any surface imperfections using INTERNS° PCT WATERTIPE. Wet sand the repaired areas and wipe clean. BARE FIBERGLASS - No Sand System: Clean the surface following the preparation procedure described above.Apply one thin continuous coat 01 INTERLUX ® FIBERGLASS PRIMER®. Follow We primer label (Erections for overcoalingApply at least 2 coals of MICRON OPTIMA, Allow proper diy limes between coats.

BARE FIBERGLASS - Sanding System: Clean the surface following the preparation procedures described above. Sand the entire s dace with 80 gut sandpaper until a flat, matte Wish is obtained. Wipe the surf ace residue oft tine solace with FIBERGLASS SOLVENT WASH 2 2. Apply at least two coats of MICRON OPTIMAL

BARE WOOD: Wel sand entire surface with 80 grit sandpaper, wipe surf ace clean wita INTERLUX0 BRUSH-EAU EMS Repair knee °chaos will INTERPROIECT WATERTRE; sand and wipe deem Apply first coal of MICRON OPTIMA reduced 10% with PAINT CONDITIONER 2161° penetrate Wu the wood. Fill seams wall Minn% SEAM COMPOUND 30. Apply second and third coats of MICRON OPTIMA unre aced. Allow proper dry times between coats.

UNDERWATER METALS: NI underwater metals must be property primed prior to application of MICRON OPTIMA with either Prima n 3100 r Meg/rota' 200002001E Contact the Interim Technical Service Depailinant at 1-1100-408-7589 far derails on how to properly Moo indeiwater metals. Do not use on aluminum. Color difference may occur between actual paint and color swatch on front of c IL

KEEP FROM FREEZING. MIX ONLY WHAT CAN BE 00101N 2 HOURS.

Dry Trine Leonel Time

Temperature ' p'f't Ov rcuatIng Soso Dry 5 0%

Relative Humidity 75%

Relative Hrubldity Humid 85%

Relative Humidity . Mtn.' MM. Min,

40 1 (NC) 2 Its 7 firs 2 WE 08 Hrs 72 ilis De Not

Apply 50 F 00 CI 2 Hrs 6 111 s 2W1 36 Ms 48 Hrs SOT (INC) 2 Ms 5 rirs 2 Wk 16 Hrs 24 His 46 HIS

76M (24'01 21115 Albs 20Th 5 Ills 7 Ilrs fill Ills ONE (3S C) 2 Iles 3I ars 2 Wk 2 Ms 5 1110 24 Ilrs

The maximum time lolauncli is ind finite, so you can launch III boat anytime after th minimum My time. e arias maximum aexihNey. Micron Optima inns be fully dry before launching. II should Tel be applied to pail or kick areas immediately ptior to launching. Put Ore can be extended slighll with lheadd.lie r of paint conditioner 20/11. Smell ainuunts of Roy Donnie re/Ira/um n closed can after mixing and beyond pot life can be used for painting pail areas for up to two weeks without losing effectiveness tioweyei, the thiclionett hem will need to be Thinned kWh( wiu Interins paint Conditioner imailmurn 10%), and thoroughly mixed lo allow for application by brush,

PRECAUTIONARY STATEMENTS HAZARDS TO HUMANS AND DOMESTIC ANIMALS

WARNING Causes eye Irritation. Harmful if absorbed through skin. Avoid contact with skin, eyes or clothing. Wear protective clothing such as gloves, long-sleeved cotton shirt, long pants, and hat. May be fatal if swallowed or inhaled. Do not breathe vapor. While sanding boat surface, wear a mask or a respirator jointly approved by the Mining Enforcement and Safety Administration and the Notional Institute of Occupational Safety and Health. Remove contaminated clothing and wash before reuse. Wash thoroughly with soap and water after handling. FIRST AID: IF SWALLOWED: • Call a poison control center or doctor immediately for treatment advice. • Have person sip a glass of water If able to swallow. • Do not Induce vomiting unless told to do no by a poison control center or doctor. • Do not give anything by mouth to an unconscious person. IF ON SKIN OR CLOTHING: • Take off contaminated clothing. • Rinse also immediately with plenty of water for 15-20 minutes. • Call a poison control center or doctor for treatment advice. IF INHALED: • Move person to fresh air. • If person Is not breathing, call 911 or an ambulance, then give artificial respiration, preferably

mouth-to-mouth if possible. • Call a poison control center or doctor for further treatment advice, IF IN EYES: • Hold eye open anti rinse slowly and gently with water for 15-20 minutes. • Remove contact lenses, it present, after the first 5 minutes, then continue rinsing eye. • Call a poison control center or doctor far treatment advice. OTHER: Have the product container or label with you when calling a poison control center or doctor, or going for treatment. ENVIRONMENTAL HAZARDS: This material is toxic to fish. Do not apply directly to water by cleaning of equipment or disposal of wastes. Do not allow chips and dust generated during paint removal to enter water. Dispose of paint debris in an approved landfill. Do not discharge effluent containing this product into lakes, streams, ponds, estuaries, oceans and other waters unless in accordance with the requirements of a National Pollution Discharge Elimination System (NODES) permit and the permitting authority has been notified in writing prior to discharge. Do not discharge effluent to sewer system without previously notifying the local sewage treatment plant authority. For guidance contact your Stale Water Board or Regional Office of the EPA. STORAGE AND DISPOSAL Do not contaminate water, food or feed by storage or disposal. Open dumping is prohibited. PESTICIDE DISPOSAL: Pesticide wastes are acutely hazardous. Improper disposal of excess pesticide, spray mixture or rinsale is a violation of Federal Law. If these wastes cannot be disposed of by uses according to label instructions. contact your State Pesticide or Environmental Control Agency, or the Hazardous Waste representative at the nearest EPA Regional Office for guidance. CONTAINER DISPOSAL: Non-refillable contains Do not re-use or refill this container. Triple rinse as follows: Empty the remaining contents into application equipment or a mix tank and drain for 10 seconds after the flow begins to drip, Fill the container 1/4 full with water and recap. Shake for 10 seconds. Pour rinsate into application equipment of a mix tank or store rinsate for later use or disposal. Drain for 10 seconds after the flow begins to drip. Repeat this procedure two more times. For Chemical Emergency, Spill, Leak, Exposure or Accident, Call TollFree - Day or Night - Chemtrec 1-800-424-9300. Medical Advisory (Minter - Contact your Local Ninon Control Center or call 1-800-85 4-681 3.

(Mtn. 13iriluxe: and 'Interluiek' are registered trademarks el Akzu Nobel.

International Paint LLC. 2270 Morris Ave., Union, NJ 07083 • 908-686-1300