Overcenter Valves are Key to Hydraulic Control

Overcenter Valves are Key to Hydraulic Control

March 27, 2012Design World Staff:0 Comments 2 By Raj Dabholkar, Chief Design Engineer, SiCV Div. and Suhas Indulkar, Manager, Business DevelopmentOften used as braking valves, these components keep HSTs from overrunning.

Traditional hydraulic valves are being ousted in favor of sleeker, lighter and hardier cartridge valves. With the ability to be mounted straight into machined manifolds that internally connect the valves rather than external piping as in the case of traditional valves, these hydraulic integrated circuits (HICs) eliminate unnecessary tubes, hoses and fittings. As each fitting provides two potential leakage points, the basic principles of hydraulic machinery operations are upheld to a higher standard.

As with the many options with traditional parts-in-body type valves, cartridge valves manifest themselves in a myriad of forms, from the humble check valve to the state-of-the-art proportional solenoid direction control valves.

The lifeguard, however, for any hydraulic actuator, is the overcenter valve. This motion controlling marvel is the successor of the counterbalance valve. The name counterbalance came from the counterbalancing weights used in the earlier machine tools to prevent the ball screw from coming under heavy load. These valves were designed in the early thirties by Harry Vickers team, who developed them as spool type valves and hence were not found to be zero leak.

While counterbalance valves maintain a healthy amount of back pressure, they force the pump to develop the full set pressure on the counterbalance spring before they allow the actuator to move. As shown in Figure 1, a counterbalance valve attached to the full-bore (cap end) area of the cylinder and set to 150 bar, at zero load, will force the pump to develop a pressure of 300 bar at the annular (rod end) area before the cylinder is allowed to move (if the annular area is half the full bore).

In turn, what the overcenter valve does is use a pilot assist from the opposite end of the actuator to move the poppet against the spring. An overcenter valve can be described as a pilot-assisted relief valve with an integral free flow check. The performance of overcenter valves are at best when mounted into the actuator, whether it is a linear (cylinder) or a rotary (hydraulic motor) actuator. However, if not, they should be connected to the actuators with rigid piping.

The disparity between a pilot-operated check valve and pilot-assisted relief valve must be noted here. While a pilot-operated check valve opens fully as soon as the pilot port develops a pressure that is sufficient to open the poppet, in case of the overcenter valve, the pilot pressure has to overcome a strong spring. The springs force is reduced by the simultaneous action of pressure on the cylinder port due to the weight of the load. In short, in pilot-operated check valves, the pilot pressure and load pressure act against each other, while in pilot-assisted relief valves, they act in the same direction against the spring. This opens the poppet gradually and causes the flow to meter.

Overcenter valves were used mainly for the following purposes:Load holding:The overcenter valve prevents the movement of a load when the directional valve is in the neutral position, permitting the use of open center directional valves and negating leakage past the spool of closed center directional valves.Load control:The overcenter valve prevents the actuator running ahead of the pump due to the load-induced energy, thereby eliminating cavitation in the actuator and loss of control.Load safety:In the case of hose failure, an overcenter valve mounted onto or into a cylinder will prevent uncontrolled movement of the load. When a cylinder is used in a boom, as in a crane, then hose failure protection is vital as the loss of load control could cause damage to people or property.

Relief setting of the overcenter valve for most applications is a matter of common sense and judgment. In the case where the load varies drastically and sudden impact loads are expected, the relief pressure could be 20-30% more than the load pressure. However, for horizontal cylinders, this could be as low as 5-10%. This ensures that with the maximum load on the actuator the valve will remain closed until pilot pressure is applied. The pilot pressure required to open the valve will depend on the pilot ratio that is the ratio between the relief area and the pilot area. The pilot pressure can be calculated as follows:

Pilot pressure = valve setting load pressure / pilot ratio

Figure 2 shows the pressure drop curves of two valves with different pilot ratios. The higher pilot ratio valve is more restrictive than the low pilot ratio valve. This shows that above a certain pressure, the lower pilot ratio valve is more efficient than the higher pilot ratio valve. It is important that the total performance is taken into account before specifying an overcenter valve.

Fig. 2: Relationship between flow and pilot ratio. Above a certain pressure, the lower pilot ratio valve is more efficient than the higher pilot ratio valve.

To explain the need for overcenter valves, the perfect example would be an inverse pendulum, as shown in Figure 3. Here, a cylinder is attached to a pendulum which has a load at its end. The cylinders retraction and extension helps the pendulum sway backward and forward. To push the pendulum from one extremity to another during its ascent, the cylinder acts against the load and the force of gravityhence the pendulum is always in control with the pump driving the load.

Fig. 3: The hypothetical inverted pendulum is the best example for the need for an overcenter valve.

As the pendulum goes over its center of gravity and starts its descent, the load becomes unbalanced, with the pendulum trying to move faster than the cylinder will allow it to. Now the load ends up driving the pump since the load and gravity are acting in the same direction as the cylinder. Here the overcenter valve would regulate the movement of the cylinder by metering the flow out of it and subsequently keeping the load in control at all times.

Fig. 4: Overcenter valves should never be connected to blocked center directional control valves. If there is a sudden switch to the block center (1) or a pressure spike due to temperature rise of the fluid (2), the fluid has no place to escape and can end up bursting hoses, damaging equipment or even putting operators lives at risk.

Since the scenario is repeated in the reverse direction, a second overcenter valve is required for the same reason on the opposite line. In this case, a dual overcenter valve is used, which regulates the flow out of a cylinder at both ends.

Dual overcenter valves also find use in track wheels of large earth moving equipment (Figure 5), where the machines are required to climb steep inclines. Equipment needs to be able to move both forward and in reverse on steep slopes. Moving forward on a descending slope and reversing on an ascending slope, the machine tends to roll forward or backward respectively. Dual overcenter valves connected to the hydraulic motors keep the load from running away by controlling the outward flow of oil in both directions. However, a parking break is a must for rotary actuators.

Fig. 5: There are cases where mobile equipment on an incline may go out of control, due to inadequate control of the track wheels. Reversing on inclines and forwarding on slopes result in the load running away.

Overcenter valves are also used on hydraulic motors in applications such as winches, as elaborated in Figure 6. Reeling in the winch while lifting the load happens against the force of gravity, which results in the pump driving the load. While lowering, however, the load and gravity act in the same direction. This results in the load running away and a possible loss of control. Here the overcenter valve meters the flow out of the hydraulic motor to keep the load in place.

Fig. 6: Winches inherently require overcenter valves to prevent load runaway while lowering the load. This however is not a fail-safe method to hold the load in place. A parking break should be installed to protect the load from falling catastrophically.

Overcenter valves are typically mounted on the cap of a linear actuator or they can be line mounted with rigid piping between the actuator and the valve. The cylinder port of the valve is connected to one end of the actuator while the valve port is connected to the directional control valve. The pilot port is connected to the opposite end of the actuator.

In Figure 7, the cylinder has to be extended against the weight of the loadthe oil flows to the cap end over the check valve extending the piston, while the opposite end is drained of oil. For retraction, the overcenter valve restricts the flow of oil out of the cap end, resulting in the pressure rising at the opposite end. This pressure is sensed at the pilot port of the overcenter valve, which, assisted by the load induced pressure, compresses the spring giving an outlet to the oil from the cap end.

Fig. 7: Operating an overcenter valve with a linear actuator.

If the load were to run away, the flow out of the cap end would increase starving the rod end of oil, resulting in a drop in pressure. Consequently, the pilot pressure would no longer be high enough to keep the spring compressed. This shuts off the flow moving out of the cylinder. In this way, the load and its movement would be back under control by continuously metering the flow out of the cylinder.

As with any hydraulic valve, there is always a functional variety. The same goes for the overcenter. The valves come in two types of relief designs. One is a direct acting relief valve which features quick response and zero leak characteristic. The other is a differential area overcenter, which gives a higher flow capacity (>300 lpm) but with a poor reseating characteristic.

Overcenter valves used in conjunction with proportional valves are required to be fully balanced and will allow the downstream pressure to be high without affecting the relief spring setting.

A note of caution: saying that the Overcenter valve is a load holding valve, is true only in the purview of linear actuators (cylinders). This is because of the inherent leakages within the motorthe rotor of the motor will always have leakages from the high pressure to low-pressure zone.

For controlling a rotary actuator, a parking brake engaged with the help of a shuttle valve, a spring-loaded cylinder and perhaps a pressure reducing valve is mandatory. Pressure in any of the lines will be sensed by the shuttle valve, keeping the parking brake disengaged. When the pressure in both the lines is zero (when the valve is in the neutral position), the pressure stops holding back the spring in the cylinder of the parking brake and engages it with the hydraulic motor, stopping its motion.

Another point of care is that overcenter valves should never be connected to directional control valves with a blocked center spool. The neutral position of the valve should always be of a float center configuration. This reduces the pilot pressure to zero in the neutral position, ensuring that the piston reseats correctly. This also means that the valve can function as thermal relief and can even eliminate unwanted pressure in the cylinder port.

Discuss this on The Engineering Exchange:

Tucson Hydrocontrolswww.tucsonhydrocontrols.com 2