osp ran renewal ret configuration v 1.4
TRANSCRIPT
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
1/33
Version Information
Version Date Changes Author
V1.0 2010-9-5 V1.0 Issues Ge Ping
V 1.1 2011-01-10 V1.1 Configuration and detail process Jesus Gomez
V 1.2 2011-01-20 V 1.2 Configuration Changes Jesus Gomez
V 1.3 2011-01-21 V 1.3 Configuration details Jesus Gomez
V1.4 2011-3--4 V1.4 add 2G configuration detail Shi Lei
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
2/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential
Security Level:
www.huawei.com
Orange Spain Project Solution
RET Configuration
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
3/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 3
RET- Remote Electric Tilt
RET: mandatory for new antennas and all bands in case of dual band
antennas. In case of antennas 900 with GSM 900 configuration,
RET activation should be quoted to Phase 1. Antennas 900
configured just for UMTS 900, RET activation should be quoted in
Phase 3. One step quotation does not distinguish between phases,
so RET is quoted in the year that the antenna is installed. For newantennas RET must also be activated in the network. Introduction
and activation of RET in reused antennas should be preciated as
an optional issue, to be quoted in an alternative TCO.
RCU
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
4/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 4
RCU
RCU-Remote Control Unit
Remote Control Units (RCU) allow operators to control the electrical tilt of
compatible antennas without direct access to the antenna.
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
5/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 5
Site ID:________________________________________________
ESN for 1stRCU (Master):_________________________________
ESN for 2ndRCU (Slave):__________________________________
ESN for 3rdRCU (Slave):__________________________________
RCU
Is necesary to record the serial of the RCU and send it with the sector and technology
specification to operation team to configure the equipment in the tool.
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
6/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential
SBT
Page 6
SBT-Smart BiasTee
The Smart Bias Tee combines the performance of a standard Bias Tee with the
function of an additional modem (AISG standard) in order to provide DC
voltage as well as remote control signals via an RF feeder cable to a TMA or
RCU.
3.Antena Port
1. Feeder Port
2. ASIG Cable
Port
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
7/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 7
2100M+900M+1800M
Distance between RRU and RCU
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
8/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 8
Scenarios
2100M+900M+1800M
RCU
RCU
Tri-band Antenna
RCU
2100M
RRU
900M
RRU1800M
BTS3900
Feeder (7/8 or 5/4)
1/2 jumper or feeder
15m Extension AISG cable
5m < Distance between RRU and RCU
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
9/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 9
Scenarios
2100M+900M+1800M
Distance between RRU and RCU>20m
RCU
RCU
Tri-band Antenna
RCU
2100M
RRU
Feeder (7/8 or 5/4)
1/2 jumper or feeder
SBT
TX/RX A
1stRCU
900M
RRU1800M
BTS3900
2nd RCU 3rd RCU
Male
connector
Female
connector
0.5m AISG cable for RCU chain connection
0.5m AISG cable from SBT to RCU
SBT*:
Smart BiasTee
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
10/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 10
Scenarios
1800M only
RCU
Antenna
1800M
BTS3900
Feeder (7/8 or 5/4)
1/2 jumper or feeder
SBT
TX/RX A TX/RX B
Male
connector
Female
connector
0.5m AISG cable for RCU chain connection
0.5m AISG cable from SBT to RCU
SBT*:
Smart BiasTee
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
11/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 11
Types of Configurations
2100M+900M+1800M
2100M connect to 1stRCU (Master RCU);1800M connect to 2ndRCU;
900M connect to 3rdRCU;
2100M/900M +1800M
2100M/900M connect to 1stRCU (Master RCU);
1800M connect to 2ndRCU;
1800M only
1800M connect to RCU with SBT;
Only RRU can connect to RCU directly with AISG cable (within 20m);
Macro BTS can not connect to RCU directly, SBT is needed for macro BTS;
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
12/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 12
Scenarios
RCU with DTMA (for master RCU)
RCU
Antenna
BTS3900
or RRU
DTMA
TX/RX A TX/RX B
Feeder (7/8 or 5/4)
1/2 jumper or feeder
2m AISG cable from DTMA to RCU
Male
connector
Female
connector
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
13/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 13
Scenarios
RCU with Combiner (for master RCU)
3G3G 2G 2G
Broad Band
Antenna
Combiner
RCUSBT
RRU BTS3900
or RRU
Combiner
RCU
3G3G 2G 2G
Broad Band
Antenna
Combiner
RCU
RRU BTS3900
or RRU
Combiner
RCU
Distance between
RRU and RCU20m
TX/RX A TX/RX B TX/RX A TX/RX B
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
14/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 14
Scenarios
RCU with DTMA and Combiner (for master RCU)
3G3G 2G 2G
Broad Band
Antenna
Combiner
RCU
RRU BTS3900
or RRU
Combiner
RCU
DTMA
TX/RX A TX/RX B
Feeder (7/8 or 5/4)
1/2 jumper or feeder
2m AISG cable from DTMA to RCU
Male
connector
Female
connector
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
15/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential
Installation Strategy of Work
Step 1:Arrive to Site
Step 2: Call Operation Team for Access
Step 3: Operation Team will contact GNOC to validate the OT
Step 4: Confirm the scenario with the information provided.
Step 5: Install the RET following the installation guide.
Step 6: Check with OM if the installation is OK.
Step 7: Rollback if there is some problem of configuration.
Page 15
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
16/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential
Operation Strategy of Work
Step 1:Arrive to Site
Step 2: Call Operation Team for Access
Step 3: Operation Team will contact GNOC to validate the OT
Step 4: Confirm the scenario with the information provided.
Step 5: Install the RET following the installation guide.
Step 6: Check with OM if the installation is OK.
Step 7: Rollback if there is some problem of configuration.
Page 16
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
17/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential
Configuration
Step 1 Set antenna line device (ALD) power switch.
Step 2Display antenna connector status.
Step 3Scan antenna line device.
Step 4Add antenna line device.
Step 5 Download the configuration file of the antenna line device.
Step 6Calibrate antenna.
Step 7Set antenna tilt.Step 8Display antenna tilt.
Page 17
Procedure for Configuration in NodeB Side
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
18/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential
Configuration
SET ALDPWRSW: CN=0, SRN=80, CASE=REGULAR, AST=CUSTOM, PSP=RET_PORT,
PWRSW=ON, UOTHD=0, UCTHD=1, OOTHD=150, OCTHD=120;
Page 18
STEP 1: Command (SET ALDPWRSW)
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
19/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential
Configuration
DSP ANTCON: CN=0, SRN=80;
STEP 2: Command (DSP ANTCON)
Page 19
This command will show the ALDPWRSW configurated before
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
20/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 20
SCN ALD: CN=0, SRN=80, ACN=R0A;
STEP 3: Command (SCN ALD)
If ALDPWRSW is well configurated this command will response with the
RCU installed, the ports and serial numbers.
Configuration
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
21/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential
Configuration
ADD ALD: NAME="RET_UMTS_S1", CASE=SECTOR_SPLITTING, DEVTP=SINGLE_RET,
RETTP=DUAL, CN=0, SRN=80, ACN=R0A, VENDOR="KA", SERIAL="CSD4745625";
Page 21
STEP 4: Command (ADD ALD)
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
22/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 22
Configuration
DLD ALDCFG: OPMODE=NAME, NAME="RET_UMTS_S1", FPATH="nombre.bin", IP="10.10.10.10",
USR="admin", PWD="*****";
STEP 5: Command (DLD ALDCFG)
For Tri-Band Antennas there are two files:
For GSM, is needed to download this file: KA_3band_80010291V01_790-960.bin
For UMTS and DCS is needed to download this file: KA_3band_80010291V01_1710-2180.bin
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
23/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential
Configuration
CLB ANT: OPMODE=CSAT, CN=0, SRN=60, ACN=R0A, DEVTP=SINGLE_RET;
Page 23
STEP 6: Command (CLB ANT)
This command takes 1- 2 minutes and will reply calibration suceded.
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
24/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 24
SET ANTTILT: OPMODE=NAME, NAME="RET_UMTS_S1", TILT=40;
STEP 7: Command (SET ANTTILT)
Configuration
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
25/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential
Configuration
Page 25
STEP 8: Command (DSP )
DSP ANTTILT: OPMODE=NAME, NAME="RET_UMTS_S1";
If the configuration is OK, the new tilt will be 4.
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
26/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential
Configuration
Page 26
Step 1 Run the BSC6900 MML command SET BTSRXUBP
SET BTSRXUBP: IDTYPE=BYID, BTSID=251,
RXUIDTYPE=SRNSN, CN=0, SRN=60, SN=0, RXUTYPE=MRRU,
PwrSwitchRET=ON, OverCurAlmThdRET=450,
OverCurClrThdRET=400, UnderCurAlmThdRET=10,
UnderCurClrThdRET=50;
Procedure for Configuration in BSC Side
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
27/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential
Configuration
Page 27
Step 2 Run the BSC6900 MML command STR RETANTSCAN:
STR RETANTSCAN: IDTYPE=BYID, BTSID=251, CN=0,
SRN=60, SN=0;
the Scan will feedback the result like:Retant Scan Result
------------------
Subroute No. = 2
Is Config = Not Config
Manufactory Information = KA
Product Information = CSD4636527
If you have 3 RCU case-cade, It will feedback 3 result.
Notes: the results are not following any order, the case-cade order
need feedback by site engineers.
Procedure for Configuration in BSC Side
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
28/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential
Configuration
Page 28
Step 3 Run the BSC6900 MML command ADD BTSRETANT:
example:
ADD BTSRETANT: IDTYPE=BYID, BTSID=251, BT=MRRU, CTRLPORTCN=0,
CTRLPORTSRN=60, CTRLPORTSN=0, DEVICENO=1, CTRLPORTNO=0,
DEVICENAME="KA_ANT1", VENDORCODE="KA", SERIALNO="CSD4636566",
CELLIDTYPE=BYID, CELLID=487;
If you have 3 RCU case-cade, execute the command 3 times.
Notes: if use SBT, CTRLPORTNO=0. if use AISG cable connect to
MRRU directly,CTRLPORTNO=2.
SERIALNO="CSD4636566 must match to the Cell ID. Otherwise the
order will change.
Procedure for Configuration in BSC Side
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
29/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential
Configuration
Page 29
Step 4 Run the BSC6900 MML command DLD RETANTCFG:
example:
DLD RETANTCFG: IP="10.113.169.141", USR="admin", PWD="*****",
FN="KA_3band_80010291V01_790-960.bin";
IP will change according to the different local server.
And if you can not download the file, please try use the FTP download
to BSC directly. The file need save to OMU:
Procedure for Configuration in BSC Side
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
30/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential
Configuration
Page 30
Step5 Run the BSC6900 MML command LOD RETANTCFG:
example:
LOD RETANTCFG: IDTYPE=BYID, BTSID=251, CN=0, SRN=60, SN=0, ANTNO=1,
FN="KA_3band_80010291V01_1710-2180.bin";
How may times need to load which is depend on how may RCU have
installed.
Please load the file which is match to RCU. Ask site engineer provide
the antenna type.
Procedure for Configuration in BSC Side
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
31/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential
Configuration
Page 31
Step6 Run the BSC6900 MML command DSP RETANTTILT:
example:
DSP RETANTTILT: OPEROBJ=SITE, IDTYPE=BYID, BTSID=251;
Please check the status of RET after load the configuration file.
If return following result, it will be ok.
Board No. Antenna No. Cell No. Subroute No. Maximum Tile Angle Minimum Tile Angle Actual Tile Angle
3 1 6 0 10degree 0degree NULL
If the maximun and minimun title angle are NULL, it means the
configuration file load error, try to check the file and load result.
The Actual Tile Angle =NULL means the antenna is not Calibrated, go to
next step.
Procedure for Configuration in BSC Side
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
32/33
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential
Configuration
Page 32
Step7 Run the BSC6900 MML command RST RETANTTILT:
example:
RST RETANTTILT: IDTYPE=BYID, BTSID=251, CN=0, SRN=60, SN=0, ANTNO=1;
Please check the status of calibrate.
If return following result, it will be ok.
Board No. Antenna No. Cell No. Subroute No. Maximum Tile Angle Minimum Tile Angle Actual Tile Angle
3 1 6 0 10degree 0degree 0degree
The Actual Tile Angle =NULL means the antenna is not Calibrated
sucsessfully, try again.
Procedure for Configuration in BSC Side
-
8/12/2019 OSP Ran Renewal RET Configuration v 1.4
33/33
HUAWEI TECHNOLOGIES CO LTD Huawei Confidential Page 33
Thank you !