optical headlight aimer from canbuilt press enter to start presentation ver 01-07/05 for perfect...
TRANSCRIPT
Optical Headlight Aimer fromOptical Headlight Aimer from Canbuilt Canbuilt
Press enter to start presentation Ver 01-07/05
For Perfect Night Vision...
The PANTHER from CANBUILT
Headlight AimingMade Easy...
Model OPT-5405
Instructions for this presentation
Use the arrow keys to view the previous or next page. Pressing enter will take you to the next page. Press “esc” at any time to close the presentation. Mouse buttons are active. Click on blue links to jump to new sections.
For Perfect Night Vision...
Table of Contents
• The Need for Optical Headlight Aimers• The Panther• Panther Advantages• Operating Instructions• Contact Canbuilt Mfg
Press “esc” at any time to close the presentation.
Proper headlight aim is a safety concern for everyone who uses our highways at night.
Headlights aimed too high or too far to the left create blinding glare for oncoming traffic.
Headlights aimed too low or too far to the right do not provide adequate light for drivers to see where they are driving.
Return to table of contents
•Passengers
•Pedestrians
•Children
Inexperienced and elderly drivers are most affected by poor headlight aim.
The danger is not only for the driver:
•Adults
•Property
•Animals
City, Country, or HighwayCars or Trucks......
Proper headlight aim is critical for all drivers!
Return to table of contents
Headlight aim is the single most important factor in the performance of
low beam headlights.
Return to table of contents
Quantitive Comparisons of Factors Influencing the Performance of Low-beam Headlights
M. Sivak, PhD, MJ Flanagan, PhD, and T. Miyokawa
University of Michigan Transportation Research
Based on a recent study by the University of Michigan,
Vertical headlight aim is even more important than having two working headlights!!!
D.O.T studies show that up to 50% of vehicles on the road today have at
least one headlight out of adjustment!
Return to table of contents
That is HALF the cars coming into your shop !
You can generate large profits by providing this important service to your customers.
Return to table of contents
Personnel: Anyone can perform this service
Area Required: No specific requirement - works in any bay
Average Service Charge: Conservative National Average: $24.95
ANNUAL PROFITS
1 Headlight Alignment per Day @ $24.95 X 52 weeks = $6,487.00
2 Headlight Alignments per Day @ $24.95 X 52 weeks = $12,974.00
3 Headlight Alignments per Day @ $24.95 X 52 weeks = $32,435.00
Fact: An alignment check in less than 10 minutes at 24.95 an alignment, That’s 149.70/hr !
In the old days there were only two types of headlights and
aiming them was easy.
Round Square
Return to table of contents
Today there are many different types of headlights.
They require an optical headlight aimer like the Canbuilt Panther for proper test & aim.
Return to table of contents
There are over 100 vehicle makes and models that can not be aimed with old style mechanical aimers.
This includes some of the most popular vehicles made, such as the Dodge Caravan, the Ford Taurus,
and the Chevrolet Impala.
Most new vehicles have aerodynamic designs that require an optical headlight aimer. Return to table of contents
IntroducingThe Panther OPT-5405
Optical Headlight Aimer
From CANBUILT MFG
Return to table of contents
The Panther OPT-5405The Panther is a professional model optical headlight aimer designed for state inspection facilities, fleet maintenance operations, collision shops, and auto or truck repair businesses.
Return to table of contents
This unique aimer quickly and accurately aims all headlight designs:• Foreign & Domestic• Car & Truck• Old & New
Including:• Euro patterns on high-end, late model cars• High mounted headlights • Tractor trailers, 4 WD’s & SUV’s• Even the new xenon lights
ALL MAKES, ALL MODELS , ALL YEARS !
For Perfect Night Vision...
How the Panther Works
Although simplistic in appearance, the Panther’s European technology has over 25 years of engineering refinement built in.
It uses an optical grade lens to reproduce a headlight beam’s image inside the aiming head.
Return to table of contents
The pattern is transmitted to an internal screen which the technician uses to aim the light.
This system provides many unique advantages:
The Panther has many advantages over other headlight aimers
Aerodynamic
Sealed Beam
Euro Style
Composite
Accurately Aims All Headlights
Contoured
Foglamps
Recessed
Sport Utility
Laser Guided Floor Slope Measurement• Permanently mounted laser.• Fast, accurate floor slope measurement• Easy access for battery change• Laser provides optional means for aligning aimer to headlight
Exclusive Linear Alignment Visor• No glare system can be used in any lighting condition• Over 6’ wide viewing range for trucks• Fully adjustable for any height user• Hairline sighting, like a gun sight• Non-reversible visor protects calibration integrity
No floor track required
Not affected by dirt, dust, or overspray
Return to table of contents
More Advantages…Exclusive Aiming Screen
•Inspection limits clearly shown on full length of screen•Domestic and European aiming including new xenon lights•1” scale for inspections•Exclusive elucidation film makes beam patterns much easier to see
Tilting Base Design
Exclusive design allows the unit to be easily tilted on two wheels, like a hand truck, to move from bay to bay.
No Electronics for Aiming
Means: no batteries, no power cords, no costly software upgrades, no programming, no adapters, no chargers, and no breakdowns.
Floor Slope Calibration SystemProvides fast, easy, multi-bay use on any floor pitch.
Retractable Pointer Positioning SystemExclusive feature provides easy, fast, alignment to headlight.
Return to table of contents
Click on image for larger view
Still more advantages...
Solid, Heavy Duty Wheels
Beam Elucidation FilterAllows use in any shop lighting conditions and helps compensate for users’ eyes sensitivity to light.
Optional Light Intensity Meter Protective Cover
Mast Calibration System IncludedFor fast, easy field calibration
Return to table of contents
Even more advantages...
•Meets SAE Standards J599 and J600
•As required for provincial inspection facilities•Compact design saves shop space
•UPS Shippable
•Affordable
Precision ground, Polished Optical Glass LensExclusive lens provides clear, accurate, beam patterns.
Locking MechanismExclusive design provides accuracy and durability by removing side to side play in aimer head.
Extruded Aluminum Mast With Built-in Lamp Height Measurement• Accuracy and calibration are protected with heavy-duty metal mast.• Aims high headlights such as 4wd trucks & SUV’s without adapters or mast extenders.• Built-in height measurement simplifies headlight aim on high mounted headlights such as 4wd & SUV’s.
2 Year WarrantyIncludes heavy-duty mast, reinforced metal base, rubber wheels, metal aimer head.
Return to table of contents
The PantherThe Pantherfrom CANBUILT MFG
Your best choice for headlight aimingtoday, tomorrow, and beyond...
Return to table of contents
For All Vehicles, All Makes, All Models, All Years !For All Vehicles, All Makes, All Models, All Years !
D.O.T. APPROVED D.O.T. APPROVED
Contact: CANBUILT MFG
CANBUILT MFG103 Milvan Dr.,Toronto. Ontario. Canada M9L 1Z7
Canada Toll Free: 1-888-607-2926Local: [email protected]
Operating Instructions
Return to Table of Contents
Press “esc” at any time to close the presentation.
Or your local distributor of automotive equipment
Operating InstructionsTable of Contents
Assembly
Initial set-up
Aiming headlights
Different types of headlights
Recognizing the beam patterns
Return to table of contentsPress “esc” at any time to close the presentation.
AssemblySTEP 1Bolt the mast, with lock washer & flat washer, and adjustment plates installed as shown, to the base.
Align the mast to the base as shown. Be sure that the threaded adjustment plate is the top plate.
Install the locknuts on the adjustment bolts, and thread adjustment bolts loosely into the top plate, only one or two turns at this time. Tighten lock nuts on adjustment bolts.
STEP 2Install optical aimer head on mast by pressing trigger lock and sliding it down the mast.
Return to operating instructions table of contents
Assembly
STEP 3Check that the mast is correctly positioned.The aimer head should be parallel to the base.Tighten the mast bolt with 10 mm allen wrench.
Return to operating instructions table of contents
STEP 4Install the lateral alignment visor.The narrow slot in the visor should face the rear of the aimer (the wide slot faces the front).
Assembly
STEP 5Install the pointer positioning system using hardware as shown.
STEP 6Attach the holder to the middle of the aimer head, at the tip of the pointer.
Assembly is CompleteReturn to operating instructions table of contents
Initial Set-upFLOOR SLOPE CALIBRATIONPrior to operation, the aimer must be calibrated for the slope of the floor in the work area. The Panther OPT-5405 uses a laser guided system for floor slope calibration.
Position aimer at front of bay. Turn on laser by turning knob on laser housing. Measure laser beam height from floor at front wheel and at back wheel.
Return to operating instructions table of contents
The distance from the floor should be exactly the same. If it is not, adjust floor slope knob until they are equal.
Initial Set-upRECORDING THE FLOOR SLOPE SETTING
Use the recorded floor slope setting for subsequent uses in the same location. Simply set the slope adjustment knob to the previously recorded position prior to aiming headlights.
Note: A decal is included with the aimer. You can record floor slope settings and adhere the decal to aimer for reference.
Return to operating instructions table of contents
Near the floor slope adjustment knob, there is a register consisting of a small cylinder that can be used to count the turns of the knob. This register sinks or raises with each turn of the knob.
Shops using the Panther in more than one location should record the floor slope settings for each location. Once the setting is recorded, it is not necessary to take the floor slope measurement again for this location.
Initial set-up is complete
SET FLOOR SLOPE KNOB
Set floor slope knob for current bay using previously recorded bay calculation or go to Initial Set-up Floor Slope Calibration.
Aiming Headlights
Return to operating instructions table of contents
POSITION AIMER TO THE HEADLIGHT
Place the aimer in front of one headlamp at a distance between 10 to 14 in. Most beam patterns are clearest if the optical lens is about 12” from the lamp surface.
Rotate aimer positioning system (pointer) to front of aimer. Move aimer so that positioning pointer is at center of headlight beam.
Return to operating instructions table of contents
Aiming Headlights
Finding the center of the lightThere are several ways to determine the center of the headlight beam.
If the headlight has a clear lens and you can see the bulb, it is generally located at the center.
Many light beams have a “dark spot” in the center of the beam, this can be easily found by placing a cloth over the light and turning on the headlights.
Some headlight lenses have a small dot in the lens that indicates the center.
Return to operating instructions table of contents
OPTIONAL METHOD OF POSITIONING AIMER
The Panther has markings drawn on the aimer which can also be used for positioning the aimer at the center of the headlight. These markings can be used instead of the pointer if desired. The laser can also be used for vertical centering.
Return to operating instructions table of contents
Aiming Headlights
Align with horizontal center of beam
View from top
View from side
Align with vertical center of beam
Aiming Headlights
Return to operating instructions table of contents
The Panther has two marks on its mast to assist in determining the headlamp height.
If the top of the aimer head is lower than the bottom mark, the headlamp is lower than 36“.
If the top of the aimer head is between the top mark and the bottom mark, the headlamp height is between 36” and 48”.
If the top of the aimer head is higher than the top mark, the headlamp height is higher than 48”. Set the beam slope knob accordingly.
QUICKLY DETERMINING HEADLAMP HEIGHT
ALIGNING AIMER TO VEHICLE
With aimer in front of the headlight, choose two symmetrical points of the vehicle located also at the same height (i.e. the upper part of the lamps, strut bolts, radiator support bolts).
Points located too high, such as the vehicles roof, should be avoided: the best accuracy is obtained using lower points.
Looking through the lateral alignment visor, make both points lie on the visor's wire, by slightly moving the aimer.
Return to operating instructions table of contents
Aiming Headlights
Aiming HeadlightsAimer is ready to test headlight.Turn on headlights and use internal screen to aim the light.
Low Beam Headlamps are aimed so that the top edge of the high-intensity zone is at the NOMINAL VERTICAL AIM line, and the left edge of the high-intensity zone is at the vertical center line of the screen.NOTE: Inspection limits are 4” (100mm) as shown on screen.
Return to operating instructions table of contents
AIMING LOW BEAM HEADLAMPS
Different Types of HeadlightsAIMING HIGH BEAM HEADLAMPS AND AUXILIARY DRIVING LIGHTS
Return to operating instructions table of contents
High beam headlamps and auxiliary driving lights are aimed so that the center of the high-intensity zone is located at the horizontal and vertical center of the screen.
Different Types of Headlights
Return to operating instructions table of contents
EUROPEAN STYLE LOW BEAMS
European low beams do not have a high-intensity zone, all the illuminated area has a similar intensity.
European type low beams are aimed so the cutoff of the illuminated zone is located at the horizontal and biased line.
Contact: CANBUILT MFG
Canbuilt Mfg103 Milvan Dr.,Toronto, Ontario. Canada
Visit our website at www.canbuilt.com
1-888-607-2926Local: [email protected]
Operating Instructions
Return to Table of Contents
Press “esc” at any time to close the presentation.