operator’s manual heavy duty wheel...

HSMFG0105

HEAVY DUTYWHEEL RAKE

WR1417

O P E R A T O R ’ S M A N U A L

TABLE OF CONTENTS

TABLE OF CONTENTS...............................................................................................INSIDE COVER

WARRANTY & WARRANTY STATEMENT..........................................................................................1

DEALER PRE-DELIVERY & DELIVERY CHECKLIST.........................................................................3

SPECIFICATIONS..................................................................................................................................5

BOLT TORQUE CHART.........................................................................................................................6

BE ALERT SYMBOL................................................................................................................................7

SAFETY RULES...................................................................................................................................8-9

DANGER - WARNING DECALS...........................................................................................................10

OPERATION WR1417.......................................................................................................................11-13

ADJUSTMENTS...............................................................................................................................14-15

LUBRICATION WR1417.........................................................................................................................16

DECAL LOCATION................................................................................................................................17

TROUBLE SHOOTING...........................................................................................................................18

ORDERING PARTS - ABOUT IMPROVEMENTS..............................................................................19

PARTS LISTS & DIAGRAMS WR1417..........................................................................................20-29

TECHNICAL HYDRAULICS...................................................................................................................30

TECHNICAL WIRING MAIN HARNESS................................................................................................31

TECHNICAL WIRING CONTROL BOX HARNESS.............................................................................32

OPEN CENTER CHANGE....................................................................................................................33

SERVICE RECORDS...........................................................................................................................34

H&S WARRANTYH&S Manufacturing Co., Inc. (“H&S”) warrants this product to be free from defect in material and

workmanship. Except as noted below, this warranty term is twelve (12) months from the date of delivery of theproduct to the original purchaser by an authorized H&S dealer. Under this warranty, H&S will repair or replace, atits option, any covered part which is found to be defective in material or workmanship during the applicablewarranty term. In no case will the covered repair cost of a part or parts exceed the replacement cost of that part.Warranty service must be performed by H&S or a dealer authorized by H&S to sell and/or service the productinvolved, which will use only new or remanufactured parts or components furnished by H&S. This warrantyincludes approved parts and labor to fix the product but does not include, and the purchaser is responsible for,any service call and/or transportation of the product to and from the dealer’s place of business, for any premiumcharged for overtime labor requested by the purchaser, and for any service work not directly related to any defectcovered under this warranty. This warranty includes only those components of the product manufactured by H&S.Warranty for any component not manufactured by H&S including, but not limited to, engines, batteries, tires, rims,hydraulic motors, pumps, etc., are covered by the warranty, if any, provided separately by their respectivemanufacturers.

This warranty in all its parts, is extended solely to the original purchaser of the product, is terminated uponany subsequent transfer or sale from or by the original purchaser and extends no third party benefits or rightswhatsoever.

The warranty term for any product used in any commercial, custom, for hire or rental application, is limited tosix (6) months from the date of delivery of the product to the original purchaser by an authorized H&S dealer.

Polybonded (polyethylene and plywood) panels utilized in H&S Manure Spreaders are warrantied, to theoriginal purchaser, to not wear through and the polyethylene overlay to not tear free of the plywood for thefunctional life of the spreader. This specific warranty on polybonded panels includes only replacement of anydefective panel part without any allowance for labor beyond the terms of the general warranty (12 or 6 months),and is further limited to manure spreaders used to spread normal agricultural manure.

This warranty does not include: (1) Any product that has been altered or modified in ways not approved byH&S; (2) Depreciation or damage caused by normal wear, misuse, improper or insufficient maintenance, improperoperation, accident or failure to follow the product Operator Manual recommendations and product decalrecommendations; (3) Normal maintenance parts and service; (4) Repairs made with parts other than thoseavailable from H&S or performed by anyone other than H&S or a dealer authorized by H&S to sell and/or servicethe product involved.

To secure warranty service the purchaser must report the product defect to a dealer authorized by H&S tosell and/or service the product involved within the applicable warranty term together with evidence of the warrantystart date and make the product available to that dealer within a reasonable period of time.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THISWARRANTY. H&S and the companies affiliated with it makes no warranties, representations, or promises,express or implied, as to the quality or performance or freedom from defect of its products other than those setforth above and NO IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS OR FITNESS FOR APARTICULAR PURPOSE IS MADE. IN NO EVENT WILL THE DEALER, H&S OR ANY COMPANYAFFILIATED WITH H&S BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. The ONLYREMEDY the purchaser has in connection with the breach of performance of any warranty on H&S products arethose set forth above.

The selling dealer has no authority to make any representation or promise on behalf of H&S, or to modify theterms or limitations of this warranty in any way.

-1-

AFTER COMPLETION, DEALER SHOULD REMOVE AND RETAIN FOR RECORDS

FRONTIERDEALER PRE-DELIVERY CHECK LIST

After the Heavy Duty Rake has been completely set-up, check to be certain it is in correct operating order beforedelivering to the customer. The following is a list of points to inspect. Check off each item as you have madethe proper adjustments and found the item operating satisfactorily.

Serial Number

(Dealer’s Name) Model Number

(Signature of Pre-Delivery Inspector) (Inspection Date)

DEALER DELIVERY CHECK LIST

This check list that follows is an important reminder of valuable information that should be passed on to thecustomer at the time this Heavy Duty Rake is delivered.

Check off each item as you explain it to the customer.

This delivery check list, when properly filled out and signed assures the customer that the Pre-deliveryservice was satisfactorily performed.

Explain to the customer that the pre-delivery inspection was made.Explain to the customer all the safety precautions they must excercise when operating this unit.Explain raking and windrow width adjustments.Explain to customer that regular lubrication is required for proper operation and long life ofmachine. Show customer the lubrication section of Owner’s Manual.Give the customer Owner’s Manual and make sure they read and understand all operating andservice instructions.Record Serial Number on page 19 of this Manual.

‘‘‘‘

‘

‘

‘

‘

‘‘

‘

Date Delivered Dealer’s Name

By

Signature of Original Buyer

-3-

All grease fittings have been lubricated (See lubrication guide in this manual).All mechanisms are operating trouble free.Rake wheels touch ground in unison when lowered into position.(Rake setting level)All bolts and fasteners are tight.All decals are in place and legible.Control Box with mount accompanies rake.‘

FRONTIER WR1417HEAVY DUTY WHEEL RAKE

Your new Frontier Heavy Duty Wheel Rake has been manufactured of the finest quality materialsand components. The performance you get from your machine is largely dependent upon how wellyou read and understand this manual and apply this knowledge. There is a right and a wrong wayto do everything. Please do not assume that you know how to operate and maintain your HeavyDuty Wheel Rake before reading this manual carefully. Keep this manual available for readyreference.

SPECIFICATIONS

Number of Wheels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17Wheel Diameter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60”Teeth per Wheel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 (18 sets of 2)Teeth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rubber Mounted In A Set Of 2Transport Width. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12’ 3”Transport Length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28’ 3”Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5800 lbs.Maximum Raking Width. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30’ 3”Maximum Finished Windrow Width. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72”Rake Wheel Hubs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Tapered BearingsRake Beam Tilt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0° to 10°Hitch Jack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .StandardTail & Work Lights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .StandardTires. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9.5L x 15SL

NOTE:Determine right or left side of Heavy Duty Wheel Rake by viewing it from the rear. If instructions orparts lists call for hardened bolts see page 6 to identify.

-5-

BEALERT! YOUR SAFETY

IS INVOLVED.

THIS SYMBOL IS USED THROUGHOUT THIS BOOK WHENEVER YOUR PERSONAL SAFETY ISINVOLVED. TAKE TIME TO BE CAREFUL. REMEMBER: THE CAREFUL OPERATOR IS THE BESTOPERATOR. MOST ACCIDENTS ARE CAUSED BY HUMAN ERROR. CERTAIN PRECAUTIONSMUST BE OBSERVED TO PREVENT THE POSSIBILITY OF INJURY OR DAMAGE.

TRACTORSThis operator’s manual uses the term “Tractor” when identifying the power source.

-7-

RECOGNIZE SAFETY INFORMATION

This is the safety-alert symbol. When you see this symbolon your machine or in this manual, be alert to the potentialfor personal injury.

Follow recommended precautions and safe operatingpractices.

UNDERSTAND SIGNAL WORDS

A signal word- DANGER, WARNING, or CAUTION - isused with the safety-alert symbol. DANGER identifies themost serious hazards.

Safety signs with signal word DANGER or WARNING aretypically near specific hazards.

General precautions are listed on CAUTION safety signs.

FOLLOW SAFETY INSTRUCTIONS

Carefully read all safety messages in this manual,and all safety signs on your machine. Follow allrecommended precautions and safe operatingprocedures.

Keep signs in good condition. Immediately replaceany missing or damaged signs.

-8-

TRACTORSThis operators manual uses the term “Tractor” when identifying the power source.

W A R N I N GTO PREVENT SERIOUS INJURY OR DEATH

Study The Above Safety RulesATTENTION - BE ALERT - YOUR SAFETY IS INVOLVED

BEFORE YOU ATTEMPT TO OPERATE THIS EQUIPMENT, READ AND STUDY THE FOLLOWINGINFORMATION. IN ADDITION, MAKE SURE THAT EVERY INDIVIDUAL WHO OPERATES OR WORKSWITH THIS EQUIPMENT, WHETHER FAMILY MEMBER OR EMPLOYEE, IS FAMILIAR WITH THESESAFTEY PRECAUTIONS.

.

Frontier always takes the operator and his safety into consideration and guards exposed movingparts for their protection. However, some areas cannot be guarded or shielded in order to assure properoperation. In addition, the operators manual and decals on the machine itself warn you of furtherdanger and should be read and observed closely.

-9-

DO NOT attempt to perform maintenance or repair with tractor running.

DO NOT step up on machine at any time.

DO NOT allow minors to operate or be near the machine.

DO NOT ALLOW PERSONNEL OTHER THAN THE QUALIFIED OPERATOR NEAR THEMACHINE.

Loose or floppy clothing should not be worn by the operator.

Stop the tractor engine, remove ignition key, and allow all mechanisms to stop before cleaning,working, or adjusting on machine.

Stay clear of hydraulic lines, they may be under extreme pressure or heat.

Stay clear of rake when opening or closing main rake arm beams, or raising or lowering rakewheels.

For transport, always make sure that the hair pin at the rear of the lift pipes, and the transportlock bracket with safety linch pins for main rake beam cylinders, are securely locked in place.

To reduce stress on rake arms, lift pipe, springs and spring brackets, reduce oil flow from tractorto lift cylinders whenever possible.

Be sure to raise rake wheels before opening or closing main rake beams.

OPERATION1. Check for proper assembly and adjustment and make sure that all bolts are tightened. Securely

retighten after a few hours of operation as bolts can loosen up on new machinery. Check wheel boltsupon delivery and periodically thereafter. Wheel bolts should be tightened at 85-95 ft./lbs. of torque.

2. Check tires and inflate to recommended pressure (9.5L x 15SL to 44 PSI).

3. Adjust the tractor hitch (13 to 17 inches above ground) and attach to tractor with a hitch pin thathas a safety locking device.

4. Remove weight from lift jack. Remove jack from pipe mount and place on convenient storage mountlocated at the rear of the front pole assembly (See Picture Below).

5. Connect hydraulic hoses for all rake functions to a double acting valve on the tractor.

6. Check tractor hydraulic system, determine if tractor is closed or open center system. The rake isfactory set-up for closed center (To change to open center, see instructions on page 33).

7. Mount control box in a convenient location on tractor. Plug 7-pin electrical connector on main harness ofrake into tractor (This will power up the control box, work lighting and safety lighting). Plug control boxinto main harness. Note: If tractor is not equipped with a 7-pin connector the tractor must be outfittedwith one.

8. Lubricate the rake completely (See Lubrication Section in This Manual).

9. Check all bolts on rake after 100 acres. Re-torque if necessary.

NOTE: Determine right or left side of your Heavy Duty Wheel Rake by viewing it from the rear. If instructions or parts lists call for hardened bolts, refer to bolt torque chart on page 6.

-11-

JACK STORAGE POSITION

OPERATION (Continued)

TRANSPORT LOCKS

RAKE BEAM LOCKSMounted on the rake beams are Self-storing transport locks for rake beam arms. Remove the clip pin andswing the transport lock toward the rake beam. There should be a fair amount of drag required to swing thelock. (A) shows the transport lock in the engaged position. (B) shows the transport lock in the storageposition, to be used when in the raking mode.

RAKE WHEEL LOCKSLocated at the rear of the lift pipe, is a hair pin which is used to secure the rake wheels in the up positionfor transport (C). When in the down, or raking position, place the locking hair pin in the convenient storageposition as shown (D).

-12-

A B

C D

OPERATION (Continued)

CENTER FRAMEWhen opening or closing the center frame of the rake,it is necessary to have forward or rearwardmotion to prevent any serious damage to rake.Each side has it’s own switch on the control box. Thereis a convenient number system on the twoslider tubes to let the operator know where eachside is located.

RAKING ANGLE/WINDROW WIDTHThe right and left rake wheel beam can be angledseparately by their own switch on the control box.By angling each side more or less the desiredwindrow width can be accomplished.

CONTROL BOXThe control box allows the operator to make manyadjustments from the tractor seat. It is set up inthree basic areas. The left side has two switches,one (A) for sliding the left center frame in or out, theother switch (B) controls the rake wheel beam angle.The right side also has two switches, one (C)for sliding the right center frame in or out, theother switch (D) controls the rake wheel beam angle.In the center of the control box there are threeswitches. The switch on the left (E) will raise and lowerthe the left side rake wheels. The switchon the right (F) will raise and lower the right side rakewheels. The switch in the center (G) will raiseand lower both left and right rake wheels.

B E F D

A G C

NUMBERS

-13-

NOTE: TRACTOR HYDRAULIC LEVER MUST BE ENGAGED TO PROVIDE OIL FLOW TO RAKE.

ADJUSTMENTS

RAKE BEAMRake beams should be adjusted so they arelevel to slightly up in the front. They can beadjusted by using the rachet jack locatednear the center of the rake. This adjustmentis important to keep rake wheel ground pressureeven along the rake beam. Failure to do thiswill cause the front wheels to make heaviercontact with the ground.

RATCHET JACK

-14-

HITCHThere are ten different positions to adjust thehitch on the Heavy Duty Wheel Rake. Hitchshould be adjusted so rake beams are level orparallel to the ground.

ADJUSTMENTS (Continued)

-15-

RAKE BEAM TILTThe rake beam can be tilted from 0° to 10°. The 0° setting is to be used in normal conditions(dry and fluffyhay). The settings up to 10° are used in harsh conditions (heavy green hay or rained on hay that is mattedinto the stubble). To adjust the beam tilt, loosen the two Tension Bolts (A). Turn the two Adjustment Bolts (B) todesired tilt (make sure the two adjustment bolts are turned in evenly). Retighten the two Tension Bolts (A)securely. Repeat the same process on opposite rake beam.

RAKE BEAM ANGLEBefore the rake beams can be angled the centerframe must be widened first (as described in theoperation section), or the rear rake wheels willmake contact. After the center frame has beenwidened, angle the rake beams to the desiredangle by using the left and right switches locatedon the control box.

GROUND PRESSURERake wheel ground pressure is adjusted by turninglocking Nut and Collar (A) in to decrease pressureor out to increase pressure. The lengthof the Threaded Rod (B), between (A) and rearSupport (C), will determine the rake wheelground pressure. Measuring this distance orcounting the threads will give you the sameground pressure on both rake beams.

B A C

NO BEAM TILT

FULL BEAM TILT

B A A B

LUBRICATION GUIDE

GREASE FITTINGSThere are twelve grease fittings on the Heavy Duty Wheel Rake. If lubricated properly and often enough, itwill prolong the life of your Heavy Duty Wheel Rake. Grease daily during normal use and before and afterstorage and after power washing. Use a good grade of high quality grease. Make sure that greasecomes out around the shaft on sleeve type bearings. Wipe off excessive grease to prevent accumulation ofchaff or grit around the bearing.

LOCATIONListed and shown are the description of location and number of grease fittings.A. (4) Two on each Lifting Cylinder MountB. (2) One on each Tandem PinC. (4) Two on each Beam Pivot (1) Top Pivot (1) Bottom PivotD. (2) Ratchet Jack

-16-

C A

D B

DECAL LOCATIONYour Frontier Heavy Duty Wheel Rake was manufactured with operator safety in mind. Located on the rakeare various decals to aid in operation, and warn of caution areas. Pay close attention to all decals.

DO NOT REMOVE ANY OF THESE DECALS. IF DECALS ARE LOST, DAMAGED,OR IF HEAVY DUTY WHEEL RAKE IS REPAINTED, REPLACE DECALS.REMEMBER: DECALS ARE FOR YOUR PROTECTION AND INFORMATION.

Listed below are the decals on your Heavy Duty Wheel Rake. These decals may be ordered individually bypart number or by ordering a complete set.ITEM PART NO. DESCRIPTIONA. HP11694A (4) DANGER - Stay Clear of RakeB. HPFRONTIER19 (2) Frontier DecalC. HP1417WR (2) Frontier Model DecalD. HP2195 (4) WARNING - Stay Clear of RakeE. HP71188B Jack StorageF. HP2X9RED (2) Red ReflectorsG. HP2X9AMBER (4) Amber ReflectorsH. HP11599 (4) WARNING - Do Not Go Near LeaksI. HPH&S Patent NumbersJ. Serial NumberK. HPFRON1 (2) WARNING - Help Avoid InjuryL. HP12197A (2) ATTENTION - Raise Rake WheelsM. HP61003 Control Box DecalN. HP21804 (2) ATTENTION - Never Adjust FrameO. SMV SignP. HP22405 WARNING - Install Transport Locks

HP0204-1417 Complete Set of Decals

-17-

F F

B

H

E G

K I

N L H J A C A G D

M

N L

O

B

P

TROUBLE SHOOTINGWARNINGMAKE SURE THAT THE TRACTOR IS SHUT OFF AND THE RAKE CAN NOT MOVEBEFORE SERVICING THE HEAVY DUTY WHEEL RAKE. MAINTENANCE AND REPAIRSERVICE WORK TO BE PERFORMED BY A QUALIFIED SERVICE PERSON ONLY.

TROUBLE... POSSIBLE CAUSE... POSSIBLE REMEDY...Main Frame Will Not Open No Electrical Power to Control Box Check and Make Sure There is Poweror Close to Control Box

Blown Fuse or Circuit Breaker Check and Replace Fuse or Circuiton Tractor Breaker

Hydraulic Lever Not Engaged or Engage Hydraulic Lever or MoveEngaged in Wrong Direction Hydraulic Lever in Opposite Direction

Hydraulic Hoses Not Connected to Check Hydraulic Hoses For ProperTractor Properly Connection

Solenoid Valve Sticking or Not Check Solenoid and ValveWorking Properly

Rake Beams Will Not Open No Electrical Power to Control Box Check and Make Sure There is Poweror Close to Control Box

Transport Locks Still Engaged Remove Clip Pin and Swing SelfStoring Transport Locks Toward Frame(See Page # 12)





Rake Wheels Will Not Raise No Electrical Power to Control Box Check and Make Sure There is Poweror Lower to Control Box

Transport Lock Hair Pins Still Remove Transport Lock Hair Pins andEngaged Place in Storage Position

(See Page #12)





-18-

-19-

INSTRUCTIONS FOR ORDERING PARTS

PLEASE RECORD NUMBERS FOR YOUR UNIT FOR QUICK REFERENCE

ABOUT IMPROVEMENTS

FRONTIER IS CONTINUALLY STRIVING TO IMPROVE IT’S PRODUCTS

We must therfore, reserve the right to make improvements or changes whenever it becomes practical to do sowithout incuring any obligation to make changes or additions to the equipment previously sold.

All service parts should be ordered through your authorized Frontier dealer. They will be able togive you faster service if you will provide them with the following

1. Model & Serial number is located on the inside right pole mount, under center frame.

2. All reference to left or right apply to the machine as viewed from the rear.

3. Parts should not be ordered from illustration only. Please order by complete part number.

4. If your dealer has to order parts - give shipping instructions:

VIA truck - large pieces (please specify local truck lines)

VIA United Parcel Service (include full address)

FIGURE 1

-20-

FIGURE 1FRONTIER MODEL WR1417

MAIN FRAME

ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION1. HPHD83 Hitch Clevis 43. HPRG100 Inner Race2. HPBFR450 Hitch Pin 44. HPRG101 Hub3. HPES7 Hair Pin 45. HPRG47 Outer Race4. HPHD84 Hitch Mount Right 46. HPRG48 Outer Bearing5. HPHD85 Hitch Mount Spacer 47. HPRG200 Washer6. HPHD86 Hitch Mount Left 48. HPRG105 Nut7. HPBFR405 1/2” x 5-1/2” Bolt GR.5 49. HPRG103 Dust Cap8. HPR35 Lock Washer 50. HPBFR144 Lug Nut9. HPR29 1/2” Nut 51. HPRG102 Stud Bolt10. HPBFR4 Jack Pin & Chain 52. HPDWM172 3/8” x 3-1/2” Bolt GR.511. HPBFR223 Jack 53. HPB68 3/8” Lock Washer16. HPHD88 5/8” x 6” Bolt GR.5 54. HPK60 3/8” Nut17. HPT69 5/8” Lock Washer 55. HPHD103 Inner Slider18. HPT68 5/8” Nut 56. HPHD183 Center Slider Outside19. HPHD89 Pole Front 57. HPHD105 Shield20. HPHD90 Pole Back Left 58. HPHD106 Poly Slide Narrow 1/4”21. HP12N24 Wheel 8 x 15 59. HPHD107 Poly Slide Wide 1/4” * HPRG128 Tire 9.5L x 15 * HPHD155 Poly Slide Narrow 3/16”22. HPLW131 1/2” x 3-1/2” Bolt GR.5 * HPHD156 Poly Slide Wide 3/16”24. HPHD92 Jack Mount Tube 60. HPHD108 Pole Back Right25. HPT144 Hair Pin 61. HPHD184 Hose Channel26. HPT143 Jack Pin 62. HP23N67 Hose Bracket27. HPT138 Ratchet Jack 63. HPHD151 Cylinder Mount Upright End28. HPHD93 Pole Pivot Pin 64. HPHD152 1/2” U-Bolt29. HPT72 5/32” x 1-1/2” Cotter Pin 65. HPHD164 Beam Pivot Plate30. HPHD94 Axle Upright 66. HPHD165 Hinge Pin31. HPHD95 Beam Pivot Left 67. HP3G22 5/16” x 1-3/4” Expansion Pin32. HPHD96 Beam Pivot Right 68. HPHD166 3/4” x 2-1/2” Bolt GR.533. HPHD153 Bushing 69. HPHD167 5/8” x 3-1/2” Bolt GR.534. HPHD181 5/8” x 7” Bolt GR.5 71. HPHD185 Hose Shield35. HPHD98 Upright Bottom Pivot 72. HPHD186 Hose Clamp (Size 48)36. HPHD99 Spindle 73. HPS414 Cap37. HPHD100 Tandem Axle Left 74. HPS415 Manual Holder Tube38. HPHD101 Tandem Axle Right 75. HPS418 Cap w/hole39. HPHD102 Tandem Pin 76. HPS416 Manual Hanger Clamp40. HP12V59 3/8” x 2-3/4” Roll Pin 77. HPHD182 Pivot Mount Plate41. HPRG98 Seal 78. HPHE42 Hose Clamp42. HPRG99 Inner BearingNOTE: * (MEANS NOT SHOWN)

-21-

FIGURE 2

-22-

53.

FIGURE 2FRONTIER MODLE WR1417

RAKE BEAMS

ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION1. HPHD109 Rake Beam Left 27. HPT69 5/8” Lock Washer2. HPHD110 Lifting Pipe Left 28. HPHSB47 5/8” Lock Nut3. HPHD111 Rake Beam Right 29. HP17G141 3/8” x 1-1/4” Bolt GR.54. HPHD112 Lifting Pipe Right 30. HPT123 3/8” x 2-1/4” Bolt GR.55. HPHD113 Stabilizer Tubing 31. HPX67 3/8” Flat Washer6. HPHD114 Turnbuckle 32. HPB68 3/8” Lock Washer7. HPHD115 Jam Nut 33. HPK93 3/8” Lock Nut8. HPHD116 Turnbuckle End 34. HPHD130 Lifting Cylinder Mount Right9. HPHD117 Rake Wheel 35. HPHD131 Lifting Cylinder Mount Left10. HPHD118 Wind Guard 36. HPHD175 Lifting pipe Collar11. HPHD119 Rake Tooth 37. HPHD91 Stand Off Mounting Plate12. HPHD120 3/4” Nut 38. HPHD132 Cylinder Mount13. HPRG103 Dust Cap 39. HPHD133 Rake Wheel Short Chain14. HPRG82 7/8” Nut 40. HPHD134 Rake Wheel Chain15. HPT172 5/32” x 1-1/2” Cotter Pin 41. HPHD154 Acme Rod16. HPHD121 7/8”ID x 1-3/4” OD Washer 42. HPBFR137 Hair Pin17. HPHD122 Bearing 43. HPR29 1/2” Nut18. HP3G18 Bearing Race 44. HPHD179 Spring Stopper19. HPHD123 Rake Arm 45. HPBFR426 Rake Pressure Handle20. HPHD124 Seal 46. HPHD157 Pivot Washer21. HPHD125 Pivot Spindle 47. HPHD158 Spindle Washer22. HPHD126 Rake Wheel Spindle 48. HPHD171 Anti-Wrap23. HPHD127 Spring 49. HPD65 1/4” Lock Nut24. HPHD128 Bushing 50. HPHD176 Spring Holder Washer25. HPRG113 Star Washer 51. HPHD178 Torsion Bar26. HPHD202 Beam Plate 52. HPRG174 5/8” x 5” GR.5 BoltNOTE: * (MEANS NOT SHOWN) 53. HPHD201 Complete Spring Assembly

-23-

FIGURE 3

-24-


HYDRAULICS

ITEM PART NO. DESCRIPTION1. HPHD135 Hydraulic Cylinder 3” x 8”2. HPHD136 Hydraulic Cylinder 3-1/2” x 60”3. HP16SV171 Hydraulic Lift Cylinder 2” x 10”4. HPBFR122 3/8” Union Adapter5. HPDWM233 3/8” Union Adapter6. HPBFR177 1” x 4” Bolt GR.57. HPHD137 Transport Lock Left8. HPHD138 Transport Lock Right9. HPBFR120 .062 Orifice10. HPBFR178 1” Lock Nut11. HPT143 Hydraulic Cylinder Pin12. HPHD139 Hydraulic Valve13. HPDWM268 9/16” Male O-Ring to 3/8” Pipe Union Adapter14. HPT144 Cylinder Pin Clip15. HPHD141 Hydraulic Hose 3/8” x 288” 1/2”MP & 3/8”MP16. HPHD142 Hydraulic Hose 1/4” x 288” 3/8”MP & 3/8”MP17. HPHD143 Hydraulic Hose 1/4” x 210” 3/8”MP & 3/8”MP18. HPHD144 Hydraulic Hose 1/4” x 36” 3/8”MP & 1/2”MP19. HPHD145 Hydraulic Hose 1/4” x 96” 3/8”MP & 1/2”MP20. HPHD147 Hydraulic Hose 1/4” x 60” 3/8”MP & 1/2”MP21. HPHD146 Hydraulic Hose 1/4” x 20” 3/8”MP & 1/2”MP22. HPWM175 1/2” 90° Union Adapter23. HPJB82 Bushing 1/2” to 3/8”24. HPBFR443 Clip Pin25. HPDF18 1/2” Check Valve26. HPDWM205 1/2” Male Quick Coupler27. HPX94 Spacer 5/16” x 1”28. HPHD187 Spacer 3/4” x 1”

-25-

FIGURE 4

-26-

-27-


WIRING

ITEM PART NO. DESCRIPTION1. HPS310 Red Tail Light2. HPS308 Rubber Light Mount3. HPHD148 Light Bracket4. HPDWM129 Yellow Hazard Light5. HPHD180 Complete Control Box w/Harness6. HPHD160 Control Box Whip7. HPHD161 Main Harness8. HPS441 Light Module9. HPHD149 Tail Light Loom10. HPDWM130 Flood/Work Light11. HP61003 Control Box Decal12. HPDWM326 Control Box Mount13. HPDWM140 Control Box Bottom14. HPHD174 Knob15. HPHD173 Panel Nut16. HPHD163 Poly Shield17. HP16SV319 Momentary Switch18. HPHD159 Master Switch19. HP16SV235 Switch Boot20. HPDWM175 Strain Relief (Cord Grip)21. HPHD150 Control Box Top

-28-

FIGURE 5


HYDRAULIC CYLINDERS

ITEM PART NO. PART NO. PART NO. DESCRIPTION1. HP23N142A HPDWM192 HP16SV157A Clevis Cap2. HP23N143A HPHD188 HPHD189 Rod Cap3. HP23N144 HPDWM194 HPHD198 Piston4. HP16SV168A HPHD190 HPHD191 Rod5. HP16SV169 HPHD192 HPHD193 Cylinder Tube6. HP16SV170 HPHD194 HPHD195 Tie Rod7. HP23N148 HPDWM198 HPDWM198 Piston Nut8. HP23N149 HPDWM199 HPDWM199 Plug9. HP23N150A HPDWM200 HPDWM200 Rod Clevis10. HP23N151 HPHD196 HPHD197 Seal Kit11. HP16SV171 HPHD135 HPHD136 Hydraulic Cylinder

LIFT CYLINDER WING CYLINDER FRAME WIDTH 2” x 10” 3” x 8” 3-1/2” x 60”

-29-

FIGURE 6

-30-

FIGURE 7

-31-

FIGURE 8

-32-

If closed center valve is used on a open center tractor it will cause the oil to heat becauseoil is dumping over relief.

Instructions for converting valve to open center:

1. Widen left side of rake using left frame width switch on control box (Remember to bemoving forward or rearward when doing this).

2. Release all pressure in hydraulic system (Shut tractor OFF and remove ignition Key).

3. Support valve bottom.

4. Remove left mounting bolt.

5. Remove 3 tie rod nuts on tank port (the outward side of valve).

6. Remove end cap, (do not loose the o-rings that are between the sections).

7. Remove plug in end cap with allen wrench, (save for future use).

8. Re-Assemble end cap and mounting angle, (torque tie rod nuts to 140 in.lbs. (16 N-M).

9. Install bolt in mounting angle.

-33-

FIGURE 9

SERVICE / MAINTENANCE RECORD

DATE DESCRIPTION NOTES

-34-

2608 S. Hume Ave.P.O. Box 768 - Telephone (715) 387-3414

FAX (715) 384-5463MARSHFIELD, WI 54449

operator’s manual heavy duty wheel...

Documents