Operating InstructionsWIFI door intercom systemItem No. 1425526

Table of Contents

Page1. Introduction ...........................................................................42. Explanation of Symbols ........................................................53. Intended Use ........................................................................54. Package Contents ................................................................75. Safety Instructions ................................................................8

a) General ...........................................................................8b) AC adapter ......................................................................9c) Exterior unit ...................................................................11

6. Controls and Connections ..................................................127. Installation and connection ................................................13

a) Installing the exterior unit ..............................................13b) Connecting the exterior unit ..........................................14

8. Installation and initial launch of the app .............................18a) Installing the App ...........................................................18b) First launch of the app...................................................19

9. Initial setup of the WiFi door intercom system ....................22a) WLAN set up .................................................................22b) LAN set up ....................................................................27

2

10. Advanced setup ..................................................................28a) Registering another device on the WiFi door intercom

system ...........................................................................28b) Deletion of the WiFi Door Intercom System from the

Device List.....................................................................29c) Setting the date and time ..............................................30d) Managingnotifications ..................................................33e) Other settings ................................................................35

11. Operation ............................................................................36a) Operation in general......................................................36b) Live image view.............................................................38c) Video recordings ...........................................................39d) Other Setting and Operating Options ............................41

12. Resetting to Factory Settings .............................................4213. Troubleshooting ..................................................................4314. Care and Cleaning .............................................................4515. Declaration of Conformity (DOC)........................................4516. Disposal ..............................................................................4617. Technical Data ....................................................................46

a) Exterior unit ...................................................................46b) AC adapter ....................................................................47

3

1. IntroductionDear customer,Thank you for purchasing this product.We kindly request the user to follow the operating instructions to preserve this condition and to ensure safe operation!

This user manual is part of the product. It contains important information on starting up and handling the device. Bear this in mind if you pass this product to a third party. For this reason, keep these operating in-structions for future reference!

If there are any technical questions, please contact:

International: www.conrad.com/contact

United Kingdom: www.conrad-electronic.co.uk/contact

4

2. Explanation of Symbols

The lightning symbol inside of a triangle is used when there is a potential risk of personal injury, such as elec-tric shock.

An exclamation mark in a triangle indicates important instructions in this operating manual which absolutely have to be observed.

Thearrowsymbolisusedwhenspecifictipsandinfor-mation on handling are provided.

3. Intended UseThe product is intended for surveillance of access to private liv-ing quarters.When the bell push button on the exterior unit is pressed, you will receiveanotificationonyoursmartphoneortabletprovided,itisconnected to the exterior unit.With the aid of the camera integrated in the exterior unit, the speaker and the microphone you can control on your smartphone or tablet, who is at the door. If necessary, the door opener can be enabled via the app. The camera is illuminated by 4 IR LEDs at dark.

5

The video and audio transmission between exterior unit and your network occurs preferably wirelessly via WLAN. Alternatively, the exterior unit can be tethered to your network via LAN. Here your smartphone or tablet is connected to your normal WLAN network as usual.Power is supplied by the AC adapter included in the delivery.For safety and approval reasons, you may not convert and/or alter the product. If you use the product for purposes other than those described above, the product may be damaged. Moreover, theimproperuseinvolvesriskssuchasshort-circuits,fire,electricshocks, etc. Please read the operating instructions carefully and do not discard them. If you pass the product on to a third party, please hand over these operating instructions as well.Observe all safety information and other information in these op-erating instructions.This product complies with the applicable national and European regulations. All names of companies and products are the trade-marks of the respective owners. All rights reserved.

6

4. Package Contents• WIFI door intercom system• Network adapter• Power adapter• Allen key• 2x dowels• 2x screws• 10x cable connector• Antenna• Operating instructions

Up-to-date operating instructionsDownload the latest operating instructions via the link www.conrad.com/downloads or scan the QR code. Follow the instructions on the website.

7

5. Safety InstructionsThe warranty will be void in the event of damage caused by failure to observe these safety instruc-tions. We do not assume any liability for any re-sulting damage!We do not assume any liability for damage to property or personal injury caused by incorrect handling or non-compliance with the safety in-structions. In such cases, the warranty will be null and void!

a) General• Theunauthorizedconversionand/ormodificationof

the product is not permitted for reasons of safety and approval.

• The product is not a toy and should be kept out of the reach of children.

• Please handle the product carefully: The product can get damaged, if crushed, struck or dropped, even from a low height.

• If you discover that the product is damaged, do not use it any longer and take it to a specialised work-shop or dispose of it in an environmentally friendly manner.

8

• Safe operation can no longer be assumed if: - the product shows visible signs of damage - the appliance ceases to function - the device was stored for a longer period of time

in unfavourable conditions - it was exposed to heavy loads during transport

• Do not leave the packaging material unattended, since it could become a dangerous plaything for children.

• On industrial sites, the accident prevention regula-tions of the association of the industrial workers’ society for electrical equipment and utilities must be followed.

• If you have any questions that are not answered in these operating instructions, please contact our technical support centre or consult a professional.

b) AC adapter• The design of the plug-in power adapter complies

with IEC Protection Class II (double insulated elec-trical appliances).

• Connect the AC adapter only to a proper outlet of the public supply network.

9

• The power socket for the AC adapter should be near the exterior station and easily accessible.

• The AC adapter is only suitable for indoor use in dry interiors; it must never get damp or wet. There is a risk of a life-threatening electric shock.

• Do not pull the AC adapter from the mains socket by pulling on the cable.

• Protect the cable of the AC adapter from sharp edges and do not step on it.

• If the AC adapter is damaged, do not touch it. There is a risk of a life-threatening electric shock!

• Switch off the mains voltage to the mains socket to which the power adapter is connected (e.g., switch off at the corresponding circuit breaker or remove the safety fuse and then switch off the correspond-ing RCD).

• You can then unplug the power adapter from the mains socket. Replace the damaged AC power adapter with an AC adapter of the same design.

10

c) Exterior unit• The exterior unit is suitable for use in in- and out-

door areas. However, it must never be used in or under water, as this will destroy it.

• Install the exterior unit in the outdoor area under an eave (e.g., a canopy).

• Make sure that the connection cable is not pinched or damaged by sharp edges.

• Mount the exterior unit in such a way that the cam-era is not pointing towards bright sources of light (e.g., sun and/or flood lights). Not only does thislead to an overexposed and unusable image, but it may also damage the image sensor due to the impact of constant exposure.

• Observe any applicable regulations that may apply to the operation of the camera and/or its orientation towards a certain ambient area before installing the exterior unit.

11

6. Controls and ConnectionsExterior unit

1 4 infrared LEDs2 Camera3 Loudspeaker4 Twilight sensor5 Sound key6 Microphone7 Tamper contact for the exterior unit; an alarm will sound, if the

exterior unit is removed from the weatherproof frame without authorization.

8 Reset button9 Drill hole for the electrical wiring harness

1

2

3

4

5 6

78

9

12

7. Installation and connection

a) Installing the exterior unitThe exterior unit should be installed in the protected outdoor area near the front door (e.g., under a canopy), so that a visitor would have to stand directly in front of it to press the bell push button.

The exterior unit should be installed in an environment that features better wireless signal strength. Use a repeater as well, if the signal at the preferred location is insufficient.Alternatively, you canalso connect theexterior unit to your network via a LAN cable.

Select the installation height so that the camera points towards the face of the visi-tor.Fasten the weatherproof frame of the exte-rior unit to the wall using suitable screws, and if required, wall plugs. Alternatively, the exterior unit can be glued to the wall merely by means of the adhesive surface on the back.An appropriate opening in the centre of the frame to route the cables is provided. A drill hole with a diameter of 8 - 10 mm is required for the wall duct.

13

Install the exterior unit on a sturdy surface only, do not use metal surfaces and do put it near other electric/electronic appliances.

Be careful not to damage cables or wires while drilling and/or bolting down! The same goes for laying the con-nection cables (voltage/power supply and door opener) and any necessary masonry.

Arrange the exterior unit into the weatherproof frame,as shown in the following picture (introduce at an angle upwards, then tilt downwards). After that secure the exterior unit in the weatherproof frame with the screw provided.

b) Connecting the exterior unitConnect all wires according to the following connection diagram.10 disposable cable splices are provided to connect the wires. Insert each of the two wires you intend to connect into one of the two holes of the splice. Then squeeze the orange part into the splice, as shown in the connection diagram.

14

• Connect the WLAN antenna included within the delivery con-tent to the terminal “Antenna” (screw connection/SMA).

• Connect the red wire of the AC adapter to the red cable “Pow-er in DC+(12V)”.

• Connect the black wire of the AC adapter to the black cable “Power in DC+(12V)”.

• Connect the door opener to the wires “Lock Relay COM” and “Lock Relay NO”. The wire coming from the door opener must be connected to the yellow cable and the wire coming from the power supply must be connected to the purple cable.The exterior unit has a potential-free door release relay with a capacity of max. 36 V (AC/DC) and max. 3 A. The door release can function as an opener.

15

Door opener of the type “Fail Secure” (working current - door opener):

This door opener is commonly used as door opener for residential front doors.

The lock of the latch in the door opener is only unlocked when operating current is present; e.g., when the door opener button in the apartment is pressed. Then the door is opened and the visitor gets access to the apart-ment. In the absence of the operating current, the door is locked.

Important! The exterior unit works only with a stabilised direct cur-

rent of 12 V/DC. Never connect AC voltage (e.g., a bell transformer) to the exterior unit; this will destroy the exterior unit; loss of guarantee/warranty!

The relay contact is potential-free, therefore both, DC voltage and AC voltage, can be connected here to op-erate the door opener.

16

• If necessary, connect to the wires “Lock Relay COM” and “Lock Relay NO” an additional doorbell. The wire coming from the bell must be connected to the grey cable and the wire coming from the power supply must be connected to the white cable.The exterior unit features a potential-free relay for an addition-al bell with a load capacity of max. 36 V (AC/DC) and max. 3 A. When the bell push button is pressed, the relay will close also.

The relay contact is potential-free, therefore both DC voltage and AC voltage can be connected here to operate the extra bell.

• Finally, we also have the option to connect the network adapt-er. This of course is only necessary if you intend to operate the exterior unit via LAN instead of WLAN.Insert the 4 wires “Net RF45” of the exterior unit into the pins of the network adapters as follows and then close the tiny trans-parent cover, which will squeeze the cables onto the contacts.Orange/white = Pin1; orange = Pin2; green/white = Pin3; green = Pin6You can now connect the network cable to the adapter as the connection to your router.

17

8. Installation and initial launch of the app

Your smartphone or tablet should be connected to the same WLAN as the WiFi door intercom system so that itcanbeconfiguredoroperated.

a) Installing the App• Open the appropriate App Store on your smart-

phone or tablet. For Android™, this is e.g., “Google Play Store”. If you are using an iPhone, iPad or an iPod Touch, open Apple’s “iTunes Store”.

• Search for the app “SafeSmart” and install it. Take note of the system requirements in the technical

data section of these instructions and the description of the app in the respective store.

Also note that the following description may change, if a newer version of the app becomes available.

18

b) First launch of the app When launching the app for the first time, you may

receive a message asking you whether you agree thatpushnotificationsaresenttoyoubytheapp.YoushouldconfirmanywaywithYesorOkinordertomakeuse of the app’s full range of functions.

The following description refers mainly to the AndroidTM App. But the process runs similar in the iOS App.

Atthestartoruseof theappfor thefirst time,youwillneedtocreate an account.This consists of an email address and/or a phone number and a password.• If not yet done, launch the previously installed app.• Tap the button Register.

19

• Select Register by email and tap the button (image at the left).

We recommend using the registration by email. Basi-cally you can also use registration by phone/mobile phone, but here in the AndroidTM App, you must still give an email address. In the iOS App, you can register only with a phone number. Then the process is almost identical, but additionally you must select your country with the country code.

• Give an email address and twice a secure password.• Finallytapthebuttonunderthepasswordfield.

20

• Once you complete the reg-istration, return to the login screen and select the login by email again.

• Enter the email address reg-istered previously and the password assigned.

• Tap the button login and con-firmtheloginwithOK.

• If all went well, you will see now the app’s main page. Youwill findaplusbutton inthe upper right.If you intend to use more than one tablet or smartphone, it is best to set up a separate account for each device. Otherwise you will only be able to receive messages on one device, if, e.g., the bell push button is pressed.

21

9. Initial setup of the WiFi door inter-com system

a) WLAN set upIn order to integrate the exterior unit into your network wirelessly via WLAN, proceed as follows.Connect:• If not yet done so already, plug the AC adapter into the mains

socket to power the exterior unit and wait for approximately 30 seconds for the start-up procedure to complete.

Important! The following description for the WLAN connection will function only, if no network cable iscon-nected.

When the door intercom system is started, short beeps will sound repeatedly with longer pauses in between. This signals the readiness for the detection of the QR codes. After some time the door intercom system exits the programming mode and beeps are not heard any longer.Unplugthesystembrieflyfromthepowersupply.

If also after several restarts, no beep is audible, reset theWiFidoorintercomsystemtofactorysettingsfirst!

Please note also that the system supports 2.4 GHz WLAN networks only. 5 GHz networks are not sup-ported.

22

Set up:• Tap + on the main page in the upper right corner.

• Now tap on the upper surface Smart Scan.• Check whether the name of the WLAN matches your WLAN

and enter the password for the WLAN network in the appropri-atefield.

• Tapthebuttonunderthepasswordfield.

23

Phone 10-15cmipad and tablet 20cm

“DING”

• The QR code with information about your WLAN is now dis-

played on the screen of your smartphone or tablet. Hold this against the camera of the door intercom. Depending on the device, keep a distance of min. 10 cm for a smartphone and max 30 cm for a tablet.If there are issues, move your mobile device a bit back and forth. Make sure that the brightness control of the display is set to high.Once you hear a single shrill sound, you will know that the QR code is detected.

• Then in the iOS App tap the button under the QR-Code, in the AndroidTM App the button in the bottom left corner. Now the WiFi Door Intercom System will connect to your WLAN Net-work automatically. This will be indicated in the app.

24

If, however, the connection fails, disconnect the inter-com for a moment from the power supply, then wait for about 30 seconds until the system is started. Press the arrow in the upper left corner, check the WLAN data once more and try again.

If it still does not work, reset the door intercom system to the factory settings and try once more.

Alternatively,youmayfirstsetuptheWiFidoor inter-com via a LAN cable and later in settings you can con-nect to WLAN manually.

• Whentheconfigurationwassuccessful,confirmwithOK. Now the app automatically switches to the main screen.

25

• If the new device is not shown, swipe down to update the list.

• Once the new device is shown, tap on it.• If necessary, change the name of the door intercom and enter

a new, secure password.• Finally, tap the button in the upper right corner to save the set-

tings.• The app returns to the main page. In the device list the new

WiFi door intercom should now show up as online.

26

b) LAN set upIn order to integrate the exterior unit into your network via LAN, proceed as follows. If the door intercom is already connected via WLAN,resettofactorysettingsfirst.Connect:• Connectfirst the1to1connectedLANcabletothenetwork

adapter of the exterior unit.• Connect the opposite side of the LAN cable to your WLAN

router or network switch.• Plug the AC adapter into the mains socket to power the ex-

terior unit and wait approximately 30 seconds for the start-up procedure to complete.

Set up:• In the upper right corner of the app’s main page, tap on +, to

add the exterior unit.• Tap the button LAN Scan.• Usually a new device is now shown in the app.

Tap on the white space of the new device.• If necessary, change the name of the door intercom and enter

a new password.• Finally, tap the button in the upper right corner to save the set-

tings.• The app returns to the main page. In the device list the new

WiFi door intercom should now show up as online.

27

10. Advanced setup

a) Registering another device on the WiFi door intercom system

If your second smart phone or tablet and the door in-tercom system are in the same network, a device that can be added should be shown after the app starts. Youmayhavetoupdatethelistfirstbyswipingitdown-wards.

Then tap on the blue surface and follow the instruc-tions.

In order to add a smart phone or a tablet manually, proceed as follows.

Please note! Even if you changed the name of the WiFi Door Intercom System, you must give only the ID when adding it. That never changes for the door intercom system.

If the first character of the ID is a 0, thatwill not beshown in the iOS app. For example, if the ID is 0123456 under AndroidTM, that will be shown and handled in the iOS app as 123456. In other words, you must give the ID to an iPhone or iPad without any 0 at the beginning.

• If the app is not on the main page, tap on the symbol in the bottom left to switch to it.

• Here, in the upper right tap on +.

28

• Select Manual.• Atthenextstep,entertheIDofthedevice.Youwillfinditinthe

device list of the other smart phone or tablet.• ConfirmbytappingthebuttonNext.• On the next page, enter the device password and tap on the

button in the upper right again to save.

b) Deletion of the WiFi Door Intercom System from the Device List

• In order to delete a door intercom system from the device list of the AndroidTM app, keep pressing on it until a pop-up appears.

• Here tap on Delete to delete the system.

29

• In the iOS app, swipe on therespective WiFi door intercom system from right to left, until the red button is shown on the right.

• Tap on Delete to delete the system.

c) Setting the date and time

• In the main view tap on the white space to the right of the

status indication of the exterior station (online/off line in blue) to set date and time. You will see a tool bar.

• Tap on Settings (gear).

30

• Then select Date and Time.• With the AndroidTMsetfirsttheDateandTime.Forthispurpose

swipe simply the relevant number upwards or downwards.• Set the time zone in the same way.• ConfirmthetimezonebytappingonthebuttonOK (next to the

time zone on the right).• In order to save it, tap on the button Apply in the bottom (date

and time are shown on the right next to it).• In order to return to the Settings Menu, tap on the arrow in the

upper left corner.

31

• With iOS, likewise, set the Dateand Time by swiping upwards or downwards.

• Confirm with the button Ap-ply below (date and time are shown on the right next to it).

• Subsequently, set the time zone likewise, by swiping.

• Confirmby tapping thebuttonApply.

• In order to return to the Set-tings Menu, tap on the arrow in the upper left corner.

32

d) Managing notificationsIn theWiFidoor intercom’ssettingsmenuyouareable todefinecertainnotificationsettings.• For that purpose, open the Settings Menu again.

• Tap on the tab with the bell symbol (Alarm Settings).• Here you can choose now whether you would like to receive

notifications,whenever thebellbuttonon theexteriorunit ispressed.For that purpose, swipe the sliding button of the tab at the top from left to right.

33

• If the push messages are switched on, you can additionally select, whether you would like to receive the messages to all smart phones or tablets that are connected. Push messages must be activated in the app, so that the relevant device ap-pears in the list.Tap on the second tab to select it.

• Here, if you do not want to receive any messages of that WiFi Door Intercom System to a device, tap on the red symbol with – in front of the relevant Account ID.

• Inthefollowingpop-upconfirmwithOK. In order to show on the device the Account ID of the

Account used, tap on the gear in the bottom right on the main page of the app. Here, at the top, the ID is shown.

• In the Menu Alarm Settings, you can also set that the exterior unit will notify you, if the device is removed from the weather-proof frame.In addition, an alarm will sound from the built-in loudspeakers which will last for about 1 minute.

• Alarmnotificationscanalsobesentbyemail.• Here also the motion detection can be turned on.

In main view you have to tap the lock to the right of the corresponding WiFi-door intercom in order to enable the motion detection feature.

34

e) Other settingsBesides the setting options already explained, the following op-tionscanbeconfiguredinthesettingsmenu(enterbytappingonthewhitefieldoftherespectivedevice-Settings):• Media settings (change video format (PAL, NTSC) or volume)• Security settings (change administrator password)• Network settings (manual adjustment for LAN and WLAN)

This setting is necessary, for example, if the exterior station was initiallyconfiguredviaLANandshouldnowconnectviaWLAN.

• Settings for the recording (for example, type of recording)• Memory card setting and information• Device update (firmware update of the WiFi door intercom

system) The setting “Defence Area” is unfortunately not sup-

ported by this product.With the gear icon at the bottom right of the app you are able to configuretheapp’sgeneralsettings(e.g.,appnotifications,log-ging off, etc.).

35

11. Operation

a) Operation in general• Ifconfiguredassuch,anotificationwillbesenttoyoursmart-

phone or tablet and a sound is heard when the bell push button on the exterior unit is pressed.

AndroidTM:• Regardless of whether the de-

vice is locked or not, this pop-up is always shown.

• Tap the right button to reject the ringing.

• Tap the left button to accept the ringing.

• Once accepted, the screen display switches automatically to live mode.

36

iOS:• Ifyour iPhone is locked,first

this message is shown.In order to switch to the app directly, swipe from left to right.

• Tap the right button to reject the ringing.

• Tap the left button to accept the ringing.

• Once accepted, the screen display switches automati-cally to live mode.

37

b) Live image viewIn live screen view additional information is shown and also taking important actions straight away is possible.• Date and time are shown at the top left.• On the right side you can adjust the image quality (HD/SD/LD). • Bottomleftyouwillfindthemicrophoneicon,whichshowsthe

active audio transmission of smartphone or tablet to the exte-rior station. You can turn this on or off with the button at the bottom on the right (5).

1 Door opener (press for 3 seconds to open; works only if a door opener is connected)

2 Speaker smartphone/tablet on/off3 Create a live image snapshot 4 Hang up; ends live display and communication5 Audio transmission to the loudspeaker of the exterior station

turned on/off

1 2 3 4 5

38

c) Video recordingsVideo Recording Settings• For that purpose, open the Settings Menu again.

• Tap on the tab with the camera symbol (Record Settings).• First specify here the preferred type of recording.• Depending on the recording mode, you can also set the re-

cording time (recording in case an alarm is triggered) or the time when recording should start (scheduled recording time).

39

Playback of the Video Records• Recorded video images can be displayed via the respective

door intercom menu.

• First tap on the white surface and subsequently in the tool bar

on Playback (Play symbol on the left).• To play back, tap on the preferred sequence.

40

d) Other Setting and Operating OptionsAdditionally, on the main page of the app, you have the option to make basic settings for the app. Moreover, basic operating op-tions are available here likewise.• The second button on the left in the bar below opens the direct

selection of the WiFi Door Intercom System.Here you can search a system in the network or activate the camera or the door communication function directly.Search the system and tap on it or type the full ID directly. Subsequently tap on the camera or handset symbol.

• The button with the bag symbol opens the menu “Tools“.Here, you can make shaking function settings, look at the cap-tured pictures and make general alarm settings.

• The gear on the right opens the system settings.Here you can edit your account, make general settings for the app and unsubscribe to use another account.However, the most important function here is the last tab with the on/off symbol. You can stop the app with this, so that it does not run in the background any more.

41

12. Resetting to Factory SettingsProceed as follows to reset the exterior unit to factory settings.• Disconnect the exterior unit from the voltage supply.• Remove the screws on the camera below and take these out

from the weatherproof frame.• Keep pressing the tamper contact (7) on the back of the cam-

era and connect the exterior unit to the voltage supply again.Wait for 30 seconds until the boot up is completed.

During the entire process, you must keep pressing the release button, otherwise the alarm will be activated! You also have the option to press the button with an adhesive tape.

• Now press the recessed reset button (8) located on the back for about 5 seconds.

• As soon as you hear a single sound, release the button.• The exterior unit will restart (which takes about 30 seconds)

and the factory setting is restored.• Disconnect the exterior unit from the voltage supply again and

release the release button (7).• Putthecameraintheweatherproofframeagainandfixthem

again with the screws.

42

13. TroubleshootingThe exterior unit does not work at all:• Check the exterior unit’s power supply (AC adapter) and the

correct wiring of the exterior unit.

The door opener does not work:• Check whether the door opener is correctly wired to the ex-

terior unit.• The switching output for the door opener is potential free. Only

an internal relay is switched here (for contact rating, see chap-ter Technical Data).You will therefore need an additional external power supply for the door opener.

Important! Never use the AC adapter of the exterior unit to power

the door opener! The AC adapter is developed exclusively for the exte-

rior unit! Never apply mains voltage via the potential-free switch-

ing contact! There is a risk of a life-threatening electric shock!

43

Only a flickering image is transferred:• Thisiscaused,forinstance,bybacklightorreflectingobjects

in the range of the camera. Find another place for the exterior unit.

Loud whistling noises are played back:• Acoustic feedback will occur when your smartphone or tablet

is too close to the exterior unit. Keep an adequate distance. • For the purpose of testing purposes, cover the opening of the

microphoneof the exterior unitwith a filmof thick adhesivetape to avoid an acoustic feedback effect.

No picture and no sound is received or transmission is dis-torted:• The distance between the exterior unit and the router is too

great or there may be too many obstacles between them (such as walls, etc.). Reduce the distance to the router or use a net-work cable for the transmission.

• Check your WLAN router and your network on proper func-tioning.

Your smartphone or tablet cannot receive push messages:• This function is possibly disabled on your mobile device or in

the app. Activate the function.• Probably the app is not open. If this is the case, open the app

and try again.

44

14. Care and Cleaning• Disconnect the product from the mains supply before each

cleaning procedure.• Use a dry, lint-free cloth to clean the product. Do not apply too

much pressure on the camera lens, as it may crack.If it is very dirty, moisten the cloth with warm water.

Never use aggressive cleaning agents, alcohol or other chemical solutions which will affect the surface of the housing (discolouration).

15. Declaration of Conformity (DOC)We, Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare that this product conforms to the 2014/53/EU directive.

The full text of the EU conformity declaration is avail-able via the following Internet address:

www.conrad.com/downloads Selectlanguagebyclickingaflagsymbolandenterthe

ordernumberof theproduct in thesearchfield; thenyou will be able to download the EU declaration of con-formity in PDF format.

45

16. Disposal Electronic devices are recyclable material and do not

belong in the household waste. Dispose of an unser-viceable product in accordance with the relevant statu-tory regulations.

17. Technical Data

a) Exterior unitOperating voltage ................... 12 V/DCPower consumption ................ max. 500 mANetwork .................................. RJ45 via adapterWLAN ..................................... 2.4 GHzImage sensor .......................... 6.35 mm (1/4”), CMOS, colourCamera lens ........................... 2.1 mmViewing angle ......................... 110° (diagonal); 90° (horizontal);

65° (vertical)Sensitivity ............................... IR light on 0 Lux;

IR illuminator off 0.5 LuxResolution ............................... HD 1280 x 720, SD 640 x 360,

LD 320 x 180 (horizontal x verti-cal); max. 30 FPS

Video encoder ........................ H.264

46

Internal memory ...................... 8 GB micro-SD card, integratedOperation at dark .................... yes; IR illuminator including

4 LEDs (Ø 4 mm); on/off 12 Lux (±2 Lux)

IR range .................................. approx. 2 mIlluminated bell push button .... noContact door opener ............... potential-free relaysContact bell ............................. potential-free relaysContact rating ......................... max. 36 V (AC/DC), max. 3 AProtection grade ..................... IP44Installation/operation site ........ protected outdoor areaSupported operating systems ... AndroidTM; Apple iOS 6 or higherDimensions (W x H x D) ......... approx. 55 x 129 x 40 mmWeight .................................... approx. 276 g (exterior unit incl.

wall mount)Operating and storage .................................................................. conditions ............................... -10 °C to 50 °C; /10% to 80%

relative humidity, non-condensing

b) AC adapterOperating voltage ................... 100 - 240 V/AC, 50/60 Hz, max.

0.18 AOutput ..................................... 12 V/DC, 0.5 A

47

1425526_V3_0217_VTP_02_m_en

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method, e.g.photocopy,microfilming,orthecaptureinelectronicdataprocessingsystems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the technical status at the time of printing.Copyright 2017 by Conrad Electronic SE.