1

DR.BABASAHEB AMBEDKAR

OPEN UNIVERSITY

Part II: Finincial Bid

Tender Document

For

INTERIOR, ACOUSTICS, SOUND, STAGE LIGHTING

& FINISHING WORK OF AUDITORIUM AT

DR.BABASAHEB AMBEDKAR OPEN UNIVERSITY.

Jyotirmay Parisar, S.G. Highway, Chharodi,

Ahmedabad-382481

2

ABSTRACT SHEET

S.N0 Item Description QTY Unit

Rate

(in

Rs.)

Total

Amount

(in Rs.)

1 Demolition including stacking of serviceable materilas and disposal of unserviceable materials with all lead and lift. (i) R.C.C. work

20.12 Cmt

2 Dismental Aluminium Section Work with All lead and Lift and stacking the material properly at the place as directed by EIC

97.65 Smt

3 Dismentaling tiled of stone floors laid in mortar including stacking of serviceable materil as and disposal of unserviceable materials with all lead and lift.

294.84 Smt

4 Dismentling steel work including distempering and stacking the materials with all lead and lift.(M.S.GRILL)

239.70 KG

5

Providing & Laying Brick work using common burnt clay building bricks having crushing strength not less than 35 kg/Sq. cm. in foundations , plinth in cement mortar 1:6 (1 cement: 6 finesand) (B) Conventional.

79.27 Cmt

6

Provdg. 15 mm. thick cement plaster in single coat on fair side of brick concrete walls and ceiling for interior plastering upto two level and finished even and smooth in Cement mortar 1:4 (1 Cement : 4 fine sand) (I) Stilt/ Ground Floor

34.78 Smt

8

S.S. HAND RAIL :Providing and fixing in position S.S. hand rail in main stair case, landing ,balconies etc. in 2"(50mm) dia Wooden top Rail, 304 grade resting on( 40 mm) S.S. pipe 1.5mm thk. 304 grade size S.S.304 grade square bars 20mm, of clear height 1meter placed at 20 cm c/c including making necessary hold fast fixture (200 mm square bars 22 cm long) embedded in staircase concrete for resting the S.S 304 grade . vertical square bars with holding etc. as per approved design and as required for the work including bending hand rail pipe to proper shape in curves with specials etc. complete ( Approved Makes -Tata/SAIL/Jindal/Essar/Bhushan Steel/Arecelor Mittal). Railing height is 1 M.

46.17 Rmt

3

9

Toughened glass partition : Providing and fixing full height toughened glass partition which include 10mm thick clear toughened glass supported on Teak wood framework of section 100mmx50mmX 50mm ( top, centre and bottom rail) screw fixed across @ 600mm C/C above right upto the bottom of RCC slab & powder coated aluminium "U" channel to be grouted in the hard flooring, Cost to be inclusive of Teak wood frame work finished in polish, And joints between glass to be filled with clear sealant, 3M film design and pattern shall be as per design of architect directed etc.Including the patch fittings of dorma or equivalent make for glass to glass Holding, Glass to Glass door.

65.74 Smt

10

MAIN GLASS DOOR : Providing & fixing in positions double shutter Glass door inclusive of side fixed glazing for main enterance Door in prefunction area with using 12 mm thick fixed Toughened Plain glass of make or any other approved equivalent make and quality,having top & bottom frame in tw of approx size 200mm x 50mm thk finished in dark melamine polish, hung with heavy duty floor spring as per architectural drawings and instructions including cutting, edge polishing, buffing necessary hardware, etc. completed with necessary fiitings ' Dorma ' make or equivalent with patch fitting as per drawing complete.

37.80 Smt

4

11

FIRE DOOR Providing and fixing of Hollow metal fire rated doors as per IS 3614 part-1 & part-2 for stability and integrity. Pressed Galvanized steel confirming to IS 277 with the following specification. Recommended fire door shall have doors tested at CBRI or ARAI for maximum rating of 2hrs with vision panel. Test certificates should be available for vision lites/panels as part of the fire door assembly. Independent glass test certificates will not be accepted. Manufacturer test certificate shall cover doors both single and double leaf and all doors supplied should be within the tested specimen, deviation in specification and sheet thickness other than what is mentioned in the test certificates are not allowed. Proper label confirming the type of door and the hourly rating is mandatory. Approved manufacturer Shakti Met-dor or approved equivalent. Door frame shall be double rebate profile of size 143 x 57 mm made out of 1.60mm (16gauge) minimum thick galvanized steel sheet. Frames shall be Mitered and field assembled with self tabs. All provision should be mortised, drilled and tapped for receiving appropriate hardware. Rubber door silencers should be provided on the striking jamb. Frames should be provided with back plate bracket and anchor fasteners for installation on a finished plastered masonry wall opening. Once frame installed should be grouted with cement & sand slurry necessary for fire doors on the clear masonry opening. Door leaf shall be 46mm thick fully flush double skin door with or without vision lite. Door leaf shall be manufactured from 1.2mm (18guage) minimum thick galvanised steel sheet. The internal construction of the door should be rigid reinforcement pads for receiving appropriate hardware. The infill material shall be resin bonded honeycomb core. All doors shall be factory prepped for receiving appropriate hardware and provided with necessary reinforcement for hinges, locks, and door closers. The edges should be interlocked with a bending radius of 1.4mm. For pair of doors astragals has to be provided on the meeting stile for both active and inactive leaf. Vision lite wherever applicable should be provided as per manufacturers recommendation with a beeding and screws from inside. The glass should be 6mm clear borosilicate fire rated glass ofrelavant rating of the door. All doors and frames shall be finished with etched primer coating, stove zinc phosphate primer and thermosetting polyurethane aliphatic grade paint of approved colour. The door leaf and frame shall have passed minimum 500 hours of salt sprey test. salt sprey test.

16.80 Smt

5

12

Providing and laying Granite slab (18mm thick) one side polished flooring over 20mm (average) base of cement mortar 1:6 (1cement:6coarse sand) or L.M1:1.5 laid and jointed with grey cement slurry including rubbing and polishing complete(item no:0.0, P.no:459) Granite stone tiles and slabs shall be pre polished (mirror polished), eggshell polished, flame finished or given any other surface treatment as specified, as per the Architectural drawings and as directed by the Engineer-in-charge.

11.00 Smt

13

Italian Marble Flooring: The best quality Pre polished Italian marble stone from approved quarry shall be machine cut and machine polished as specified in respective items and shall be of specified thickness ( av. 10 to 15 mm )and of approved quality and size, free from cracks and flakes and shall be uniform colour, with straight edges. The sides of machine cut and machine polished stones shall have perfect right angles and surface smooth. The stone slabs shall be laid and finished on bedding of cement mortar 1:4 (1 cement: 4 coarse sand) 20 mm (average) thickness. The flooring work will be inclusive of 100mm high skirting which flushed with the wall & with a 5mm high groove above it. The Italian marble skirting is laid on min 20mm thick cement mortar of ratio 1:3 (1 cement: 3 coarse sand) and joined with white cement slurry mixed with matching colour pigment, to match the shade. The finished stone surface thus laid to the required degree as approved by the Architects. Rate shall be inclusive of p.o.p protection, cleaning of the floor and disposal of debris from site, in all respects, up to final handover of the site. The tolerance of the stone slab should be followed as per the Granite stone item. Basic rate for Italian Marble : Rs. 350.00 / sqft

9.00 Smt

14

SIGNAGES : Providing and fixing name plate (letters)made by using nikalight radium take and stic on 3mm thick acp sheet , the whole name plate shoula be fixed on m.s. pipe (25mmx25mm) box type structure of required size as directed by engg in chrge the rate including fitting, carting etc complete

18.00 Nos.

6

15

Providing Kiosk in Foyer area for food court : Work includes all carpentary work in 12mm water proof ply, with counter top in 12mm thick staron solid surfaces colour as approved by BAOU/Architect with all necessary hardware, materials and labour charges. More details please Refer Drawing no : AR.TD.06 which is enclosed with the tender

1.00 Each

16

Providing and fixing 2nd class teak wood plain lining tongued and grooved on and including wooden plugs laminated wooden flooring tiles / strips (25mm thick) from Pergo or Equivalent brand on 25 to 35mm IPS Floor finish. Floor Beading to be provided at the junction of the wooden flooring & any other flooring materials. (for floor exercise area, circulation area in stage.) Fixing to be done as per manufacture's specification.

354.00 Smt

7

17

Gypsum False Ceiling Providing and fixing gypsum board false ceiling consists at G.I perimeter channels of size 0.55 thick having one flange of 20 mm and another flange of 30 mm and web of 27 mm along with perimeter of ceiling, screws fixed to brick work / concrete / partition with help of nylon sleeves and screws at610 mm centre. The suspending G.I. intermediate channels of size 45 mm(0.9 mm thick with 2 flangs at 15mm each from the soffit at 1220 mm centrewith ceiling angles of width 25mm x 10mm x 0.5 mm thick fixed to soffit withG. I cleat and steel expansion fastners ceiling section of .55 thick having kurled web 51.5 mm and 2 flangs at 26 mm each with lip at 10.5 mm are fixed to intermediate channel with help of connecting clips and in direction perpendicular to the intermediate channel at 450mm centre to centre including 12.5 mm tapered edge Gyp board conforming to IS 2095 – 1982 is then screw fixed to ceiling section with 25mm dry wall screws of approved quality and make at 230mm centre, screw fixing is donemechanically with drilling machine with suitable attachment. Finally tapered edges at the cupboard are to be joint and finished so as to have a flush look which includes filling and finishing with jointing compound, paper tape etc. complete. Rate to be included all kinds of profiles, upright, curves,cutouts required for light fixtures, speakers, sprinklers, smoke detectors, trap doors, A.C. grill, diffuser etc including additional support if required of duct portion, marking grid on ceiling, including all drops, offsets, curvature small moulding and in desired geometrical pattern, including 2 coats of primer, plaster putty and minimum 3 coats of plastic Emulsion paint as per manufactures specification, scaffolding.

270.00 Smt

8

18

Wooden Acoustic Paneling auditorium spectator seating area (lower edge or reach- floor to 2.44 mt high) Providing and fixing wall acoustical paneling using ecotone Slato Acoustic Panel make Slats L-16 of size 128mmx2430mmx16mm thick up to 2400mm high as per the following specification :-Slats L-16- 2mm @16mm, 32 x 128 x 2430 mm high grade Pine wood base Medium Density Fiber acoustic boards with Tongue & Groove Edge,2mm slot perforation @ 16mm centre, slates perforations, The acoustic should be furnished with a Black absorbent felt backing with an airflow resistance of 330-460 Ns/m³ (DIN 53887),wood practical core,NRC : should be Up to 0.75,should meet the safety requirements of EN 14190 and Useing 50MM Thick 1000 GSM ecotone make synco PF wool as baking material . Fixing :- Sound Strut CC18 screw fixed horizontal/vertical to wall at every 600mm c/c. Metal cleat can be fixed on top edges of Sound Strut CS55 fixed directly by stamping to the CS55 and IC91 which is screw fixed directly to the wall where ever required with a backing black color fabric as approved by Architect and as specified including all accessories, material & labor complete as directed by Architect / Engineer.

119.01 Smt

9

19

LOOP PILE CARPETS FOR PASSAGE AND ENTRY AREA/VIP LOUNGE AREA Supply and fixing of Loope Pile Carpet of Pile Fiber: 100% Bcf Polypropliene Yarn Construction & Type: Solution Dyed Bulk Continuous Filament Machin Gauge & Stich Rate: 2.54mm (1/10”) 39.4 Rows/100mm, 48/10 Cms. Construction: Loop Pile High Low Scroll Graphic. Density Factor: 189,600 Tufts/Sq.Mts Tufted Pile Weight & Hight: 650 Gm/Sq.Mt, 6mm (5 %+/-) Backing: Primary: Woven Polyproplene, Secondery: Action Back Moth Proffing: Naturally Resistat Bond Strength: 30 Newton Tuff Withdrawal Strength: 20 Newton Flammability: (Astm D 2859-96 & Cpsc-Ff-170) 8 Passes Static Generation: Under 3 Kv Light Fastness: 5+ Usage Area : Commercial Heavy Duty Like Auditiriom Office 7 Heavy Traffic Area with backing of 8mm thick armour fixing on the floor with using favicol SR 505 solution and fixing the carpet above armour including all accessories, material & labor complete as directed by Architect / Engineer – in – charge.

216 Smt

10

20

ACOUSTIC DOOR Providing & fixing of teakwood Four side door frame of section 150x65mm along with fire and smoke in tumescent seal strip of size 12mmx4mm for 120 minutes fire rated and rw 35db acoustic door with minimum thickness of 93mm having infill of 45mm thick resin bonded glass wool of 48kg/m3 density sandwiched by two 12mm thick magnesium board (edge to edge on internal hardwood frame)and cladded with 6mm thick commercial ply facing and 3mm sheet rubber interlayer T.And finished with 1mm thick laminate as per designer and 25mm thick teakwood frame around the door panel as shown in the drawing. The board shall be resistant to vermin, mold growth, minor impact, abrasion and short term water attack and shall be in color as approved by the designer, the door shall have acoustic seal in door rebates and drop dead seal at the bottom of the door, the sound reducing doors also include door closer, door coordinator, panic bar with outside key and including all accessories, material & labor complete as directed by Architect / Engineer – in – charge. Size 2.40 x 1.50 x 6

21 Smt

11

21

MAIN CURTAIN Main Curtain Providing & supplying including stitching decorative main curtain, vertically up down slider in art silk, velvet fabric of approved shade and quality. The curtain shall have 100% gathering cloth complete with bottom silk thread lace and same colour grout up to room height. The curtain shall be with vertical sliding arrangement complete with fixing rails, brackets, sliding arrangement & motorized operation complete with runners, master runners, pullies, 6mm to 8 mm steel wire rope, 1.5 HP three face motor. Air breaker contractors , micro switches for auto stop, push button remote control for forward, reverse and stop positions. The curtain should be vertically up down with maximum gathering position. Hamming and bottom finishing at site etc. complete as directed by E.I.C./Architect of the project. Providing & fixing 35 mm dia road for curtain control equipment with necessary M.S. flat support from ceiling with scaffolding, leveling, necessary M.S. bracket including all accessories, material & labor complete as directed by Architect / Engineer – in – charge. Opening size : 30 x 5.50 mtr . Basic Rate of Fabric/ valvet=250/rmt Remote control system. Seven years warranty for mototrized system. Auto system can be manually operated system in case of emergency or power failure.

1 Nos.

12

22

PROSCENIUM Providing, making and errecting 325mm high (height from finish top of existing stage) Proscenium as per architectural drawing and instructions . The system shall be comprising of following .Frame work- Providing. making and fixing teak wood frame work made out of 38mm x 38mm @ 600 mm c/c in both ways fix properly to the existing stage from bottam of the stage as per drawing. Top portion of vertical members shall be curve/ bend as per drawing. Ply - Providing and fixing 8 mm thick flexi commercial ply fixed on peripheri of the frame including boxing for conduting as per architectural drawings and instructions including cutting, necessary hardware, drilling, cut out and necessary support for switch boxes and lightfittings and finish the Ply with 1mm thick approved laminate (Laminate to be approved by architect before commencement of work) at visible side. All connections in framework shall be with GI screws of approved quality and cleaning etc. completed at all floors and heights as specified and directed by Architects/ EIC.

29.7 Smt

23.1

PELMET Providing and fixing pelmate mon and around All doors in 12mm thick acrylic based solid surfaces over 6mm thick water proof ply. Rate inclusive of all materials, labours and finishing, etc. as per Architectural drawings and details

54 Smt

23.2

PELMET Providing & supplying including stitching decorative pelmet in Art silk velvet fabric of approved shade & quality. The pelmet shall have 50% gathering cloth including bottom silk fringe of same colour or as approved with brass hook suspension with university logo and writing as per your requirement etc. including all accessories, material & labor complete as directed by Architect / Engineer – in – charge. Size : 30mtr. X 1 mtr.

30 Rmt

13

24

WINGS Providing & Fixing wings(sliding partition) made out of black/blue glazed cotton cloth fixed on wooden frame as per drawing & instruction stated below.: (a) Partition frame shall be made in 75*50 mm with necessary bracking in same thichness in Devdar wood and (soft wood) and as per drg. Light weight partition. (b) Above frame shalll be covered by blue/black colour glazed cotton fabric by black nailing. (C)Top member have sliding fitting in aluminium channel & bearing wheel or in wooden channel etc. including all accessories, material & labor complete as directed by Architect / Engineer – in – charge.

114.24 Smt

25

Frills Providing & supplying including stitching glazed cotton blue colour fabric drop (frill) above the stage. The drop shall have 50% gathering cloth the curtain is to be suspended from G.I.pipe with string and hooks etc. complete as directed by engineer in charge/architect of the project. (a) Providing/Supplying/fixing 'B' class 50 mm dia. Gi pipe for curtain/frills,suspension as per drawing shown complete with bend coupling,socket, nut bolt scaffolding if require weldung with one coat of red oxidewith nails etc, at site including all accessories, material & labor complete as directed by Architect / Engineer – in – charge. Opening size :(20.10mtr x 1.80 = 36.18 + 20.10mtr. x 1 = 20.10(4

116.58 Rmt

14

26

Wirelee MIC Reciver SITC of Professional reference multichannel wireless microphone receiver : RF carrier frequency ranges - 500-530, 570-600, 650-680, 680-710, 720-750, 760-790, 790-820 MHz; Modulation -FM; Audio bandwidth should be 35 to 20,000 Hz or better; THD - <0.3% typicalo or better; Signal/noise ratio - >120 dB(A) typical or better; Should have audio output- balanced 3-pin XLR (Output level adjustable to –30, 0, +6 dB) unbalanced TS ¼” jack, RF Radiation should be 50 mW max. (ERP) or better Approved Makes: JBL( AKG), Revolabs, Audio Master,Bose or equivalent

4.00 Nos.

27

Wireless Handale MIC SITC of Professional reference wireless Handheld Transmitter RF carrier frequency ranges - 500-530, 570-600, 650-680, 680-710, 720-750, 760-790, 790-820 MHz; Modulation -FM; Audio bandwidth should be 35 to 20,000 Hz or better; THD - <0.3% typicalo or better; Signal/noise ratio - >120 dB(A) typical or better; RF Radiation should be 50 mW max. (ERP) or better; Approved Makes: JBL( AKG), Revolabs, Audio Master,Bose

2.00 Nos.

28

Wirelss Body PACK Transmitter SITC of Professional reference wireless Body Pack Transmitter : RF carrier frequency ranges - 500-530, 570-600, 650-680, 680-710, 720-750, 760-790, 790-820 MHz; Modulation -FM; Audio bandwidth should be 35 to 20,000 Hz or better; THD - <0.3% typicalo or better; Signal/noise ratio - >120 dB(A) typical or better; RF Radiation should be 50 mW max. (ERP) or better; Approved Makes: JBL( AKG), Revolabs, Audio Master,Bose or equivalent

2.00 Nos.

15

29

Lavelier MIC SITC of Professional Lavelier Microphone Audio frequency bandwidth 20 to 20000 Hz, Sensitivity 13 mV/Pa, Signal to Noise 57 dB-A Electrical impedance at 1 kHz 5,000 Ohms, Self noise 35.5 mW Notes Measurements in working distance (2-3 cm from sound source), Polar Patterns : Cardioid, Approved Makes: JBL( AKG), Revolabs, Audio Master,Bose or equivalent

2.00 Nos.

30

Active UHF Antenna SITC of A wide-band UHF active Antenna and Power Splitter that can feed up to 4 receivers Carrier range: 470 to 952 MHz , Attenuation: 0, 2, 4, 6, 8, 10, 12, 14 dB switchable, RF inputs: 2 x BNC sockets, 50 Ohm, RF outputs: 10 x BNC sockets, 50 Ohm, Power requirement: 12 VDC / 5A Approved Makes: AKG, Revolabs, Clock Audio.

2.00 Nos.

31

Antenna Cable with BNC SITC of Antenna Cables.Antenna cable for Wireless systems, 20m length, BNC connectors. The cable for connecting external antennas, antenna boosters, antenna booster supplies, antenna power splitter and receivers shall be an RG 58 cable (50 Ohms), length 20m, gold plated BNC connectors on both ends. Approved Makes: JBL( AKG), Revolabs, Audio Master,Bose or equivalent

4.00 Nos.

32

Active Paddle Antenna SITC of External directional active "paddle" antenna. Switching bandwidth (from/to) 470 to 952 MHz, Antenna gain 21.5 dBi, Covering angle 70 Grad, Amount 1, Type BNC, Gender Female, Note RF output (50 Ohms), Recommended load impedance 50 Ohms Approved Makes: JBL( AKG), Revolabs, Audio Master,Bose or equivalent

2.00 Nos.

16

33

Antenna Combiner SITC of Antenna Combiner, Two to one antenna combiner for indoor and outdoor use. Can be used either to split signals or combine them if needed. Approved Makes: JBL( AKG), Revolabs, Audio Master,Bose or equivalent

2.00 Nos.

34

Wired MIC SITC of Professional dynamic vocal microphone , Polar patttern - Supercardiod; Audio frequency bandwidth - 70 to 20000 Hz or better; Sensitivity- 2.6 mV/Pa or better; Electrical impedance - 600 Ohms or better ; Recommended load impedance - 2000 Ohms or better; Type - Balanced XLR or better Gender - Male; Contacts - 3-pin. Approved Makes: JBL( AKG), Revolabs, Audio Master,Bose or equivalent

2.00 Nos.

35

Instrumental MIC SITC of Professional instrumental microphone dynamic moving coil; should have frequency bandwidth - 75 to 20000 Hz or better; Equivalent noise level- 18 dB-A ; Sensitivity - 4 mV/Pa (-48 dBV) or better; Electrical impedance <=200 ohms or better; Recommended load impedance - >=1,000 ohms or better; Output connector - 3-pin XLR-type. Approved Makes: AKG, Revolabs, Clock Audio.

2.00 Nos.

36

Active Dia BOX SITC of Active Di Box : Input 1 instrument/line/speaker level Input Connectors 1/4" jack, Input Type Unbalanced, RF filtered Insert Impedance 150k Ohm typical, Max Input +20dBu (0dB pad); +40dBu (20dB pad); +60dBu (40dB pad), Output (Thru) 1 parallel from input jack, 1/4" Unbalanced, RF filtered, Output Connectors XLR male balanced, Output Impedance 150k Ohm typical, Max Output 0dBu Transformer Custom dbx mu-metal-shielded, JBL, Bose or equivalent

1.00 Nos.

17

37

Drum MIC Set SITC of Drum Set Session I with 1 x P2 bass drum microphone, 2 x P17* for overheads,4 x P4 for toms and snare Approved Makes: JBL( AKG), Revolabs, Audio Master,Bose or equivalent

1.00 Nos.

38

32 Ch Sound Mixer SITC of 32 Ch Digital Mixer 32 mono mic inputs, 8 line inputs, 80 channels to mix, 2 ViSi Connect™ option card slots for 128 x 96 input/output paths, Pre/Post selection per input per bus, Freely assignable faders and patching, Soundcraft FaderGlow™, Colour backlit LCD screens per fader, GEQ on every bus, 20 sub-group / aux busses, 4 FX busses, 8 Matrix busses, LRC Mix busses, LCR panning, 4 Stereo Lexicon Effects engines, Delay on inputs and outputs, 8 Mute Groups, 8 VCA Groups, AES in and out, DMX interface and control - control sound and light simultaneously Aprrroved Make : Soundcraft/ midas / Allen & Heath

1.00 Nos.

39

Headphone for sound operator SITC of Control Room head phone for FOH Monitoring Headphone type closed-back, Max. Input Power 200 mW, Audio frequency bandwidth 16 to 28000 Hz, Sensitivity headphones 104 dB SPL/V ,Rated Impedance 55 Ohms, Earpads , Detachable cable yes, Cable Length 3 m, Earpads replaceable yes, Type Stereo plug – 3.5mm (1/8-inch) with 6.3 mm (1/4”) screw-on adapterApproved Makes: AKG, Revolabs, Clock Audio.

2.00 Nos.

40

Green room speaker SITC of Bi-amplified Studio Monitor with Magnetically-Shielded 5” Low Frequency Transducer and 1” Soft-Dome High Frequency Transducer and Image Control Wave Guide, Frequency Range 43 Hz-24 kHz Max Peak SPL 108 dB SPL C-Weighted, Max Peak Input +23 dBu, LF Driver Size 127 mm (5"), HF Driver Size 25 mm (1"), LF Driver Power Amp 41 W Class D, HF Driver Power Amp 41 W Class D, LF Trim Control +2 dB, 0, -2 dB, HF Trim Control +2 dB, 0, -2 dB Approved Makes: Bose, JBL, QSC, Tanoy.

2.00 Nos.

18

41

Digital Sound processor SITC of Networked DSP with Signal Processor with Digital Audio Bus and Dante : Four Input / Output Card Slots, Configurable Inputs / Outputs, Analog Inputs (with Phantom Power per Channel), Analog Outputs Digital Inputs (AES/EBU and S/PDIF), Digital Outputs (AES/EBU and S/PDIF), AEC Inputs (with Phantom Power per Channel), Telephone Hybrid Card, Configurable Signal Processing, Rich Palette of Processing and Logic Objects, Dante Audio, 256 Channel, Low Latency, Fault Tolerant Digital Audio Bus, Clear Front Panel LED Indication, Informative Front Panel Display, Bi-Directional Locate Functionality, 12 Control , Inputs and 6 Logic Outputs for GPIO Integration, Approved Makes: BSS, JBL(Clearone), Bose. or equivalent

1.00 Nos.

42

Input Cards SITC of Input Cards Analog Inputs: Up to 4 electronically balanced on Phoenix/Combicon removable screw connectors, Mic/Line Inputs: Nominal gain 0dB, electronically switchable up to +48dB,in +6dB steps Input Impedance: 3.5kΩ,Maximum Input Level: +20dBu with 0dB input gain,+8dBu with 12dB gain, CMRR: >75dB at 1KHz Input Noise (E.I.N.): <-128dBu typical with 150Ω source Phantom Power: 48V nominal, selectable per input A/D Latency: 38.7/Fs Approved Makes: BSS, JBL(Clearone), Bose. OR EQUIVALENT

4.00 Nos,

43

Output Cards SITC of Output Cards Analog Outputs: Up to 4 electronically balanced on Phoenix/Combicon removable screw connectors, Maximum Output Level: +19dBu, Frequency Response: 20Hz-20KHz (+0.5dB/-1dB) THD: <0.01% 20Hz to 20KHz, +10dBu output, Dynamic Range: 108dB typical, 22Hz-22KHz unweighted, Crosstalk: <-75dB, D/A Latency: 28/Fs Approved Makes: BSS, JBL(Clearone), Bose. or equivalent

4.00 Nos,

19

44

Wall Controller SITC of Programmable Controller Ethernet Wall Controller, Compatible with BSS Audio Soundweb London, Crown DCi, and other HiQnet devices, Available in Black or White, Available in US Decora or EU Version, Dual-Gang Size, PoE (Power Over Ethernet), Configured within Audio Architect via Drag-and-Drop, 1 Programmable Push/Rotary Encoder, 1 Programmable Encoder Ring (Multicolored), 8 Programmable Buttons (Multicolored), 2 Programmable 64x128 Pixel LCDs (Multicolored)Approved Makes: BSS, Clearone, Bose.

1.00 Nos,

45

Poe Addptor SITC of Power Adaptor 10/100/1000 (MbPS) Data Rates, Meets IEEE802.3af requirements, Regulated Output, 100/240 VAC Universal Input Approved Makes: Crestron, AMX, Extron

1.00 Nos,

46

Advanced Feedback processor SITC of Advanced Feedback Suppressor Full LCD Display, dbx’s patented (Advanced Feedback Suppression) AFS™ technology, 24 Programmable Filters per Channel, Stereo or Dual Independent Channel Processing, Live and Fixed Filter Modes, Selectable Filter Lift Times, Application-specific filter types include: Speech and Music Low, Med and High, Input channel Metering, 24 LED per Channel Filter Metering,

3.00 Nos,

47

FOH Spaeker SITC of High Power 3-Way Loudspeaker with 1 x 15" LF & Rotatable Horn: Frequency Range (-10 dB) 38 Hz – 20 kHz, Frequency Response (±3 dB) 45 Hz – 18 kHz, Coverage Pattern /64: 60° x 40°, rotatable waveguide /95: 90° x 50°, rotatable waveguide, Directivity Index (DI) 13 dB Crossover Modes Tri-amp/Bi-amp switchable, Crossover Frequencies 300 Hz and 2.3 kHz, Approved Makes: JBL, QSC, Tanoy.

3.00 Nos,

20

48

Four CH Amplifier SITC of Four channel 1250W@4Ohm Amplifier requency Response ( 8 Ohms, 20 Hz - 20 kHz) +/- 0.25 dB, BLU Link Input Signal to Noise Ratio (A-Weighted) > 104dB, Total Harmonic Distortion (at full rated power, 20 Hz - 20 kHz) 0.35%, Voltage Gain 34 dB, Damping Factor (20 Hz to 100 Hz) >1500, Input Impedance (nominal balanced, unbalanced) 10 kOhms, 5 kOhms, Maximum Input Level before Compression +20 dBu Load Impedance (Stereo/Dual Mode) 2 - 16 Ohms; 70Vrms and 100Vrms Load Impedance Bridge Mono 4 - 16 Ohms; 140Vrms and 200Vrms Approved Makes: Crown, QSC, Powersoft, JBL, Bose or equivalent

3.00 Nos,

49

Eight CH Amplifier SITC of Eight channel 600W@4Ohm Amplifier : Frequency Response ( 8 Ohms, 20 Hz - 20 kHz) +/- 0.25 dB, BLU Link Input Signal to Noise Ratio (A-Weighted) > 104dB, Total Harmonic Distortion (at full rated power, 20 Hz - 20 kHz) 0.35%, Voltage Gain 34 dB, Damping Factor (20 Hz to 100 Hz) >1000, Input Impedance (nominal balanced, unbalanced) 10 kOhms, 5 kOhms, Maximum Input Level before Compression +20 dBu, Load Impedance (Stereo/Dual Mode) 2 - 16 Ohms; 70Vrms and 100Vrms, Load Impedance Bridge Mono 4 - 16 Ohms; 140Vrms and 200Vrms Approved Makes: Crown, QSC, Powersoft, studio master, JBL, Bose or equivalent

5.00 Nos,

50 Accessory SITC of Forged Shouldered Steel Eye bolt 3 pcs pack

8.00 Nos.

21

51

Subwoofer Speaker SITC of Dual 18" Subwoofer Frequency Range 28 Hz – 1 kHz (-10 dB), Frequency Response 35 Hz – 1 kHz ( ± 3 dB), Input Modes Drivers Parallel / Drivers Discrete, Transducer Power Rating (AES) 2400 W (9600 W peak), 2 hrs, Long-Term System, Power Rating (IEC) 1600 W (6400 W peak), 100 hrs, Maximum SPL 30 Hz – 100 Hz: 136 dB-SPL cont avg (142 dB peak), 100 Hz – 500 Hz: 136 dB-SPL cont avg (142 dB peak), System Sensitivity , (dB-SPL, 1W @ 1m) 30 Hz – 100 Hz: 102 dB , 100 Hz – 500 Hz: 102 dB, Nominal Impedance 4 ohms in parallel-drive mode 2 x 8 ohms in discrete-drive mode Approved Makes: JBL, QSC, Tanoy.

2.00 Nos.

52

Loaudspaeker SITC of Single 8" Loudspeaker : Frequency Range 52 Hz - 20 kHz (-10 dB) Frequency Response 63 Hz – 19 kHz (±3 dB), Power Rating : 250W Cont. Pink Noise, 500W Program, 1000W Peak, Impedance 8 ohms Approved Makes: JBL, QSC, Tanoy.

6.00 Nos.

53 Braket SITC of Mounting Bracket for above Loudspeakers

6.00 Nos.

54

Monitor speakar SITC of 12" Two-Way Stage Monitor and Powered Loudspeaker System System Type Self Powered 12”, two-way, bass-reflex, Maximum SPL Output 135 dB peak, Frequency Range (-10 dB) Design Highly efficient Class-D amplifier, Power Rating 1500W (750W x 2), AC Power Input 100V - 240V ~ 50/60 Hz, LF Driver 1 x JBL 272G 305 mm (12 in) woofer, HF Driver 1 x JBL 2408H-2 37.5 mm (1.5 in) annular polymer diaphragm, neodymium compression driver, Coverage Pattern 90° x 50° nominal, Directivity Index (DI) 10.2 dB, Directivity Factor (Q) 10.4, Enclosure Asymmetrical, 18 mm, plywood, Suspension / Mounting Dual 36 mm pole socket, 12 x M10 Suspension Points Approved Makes: JBL, QSC, Tanoy

6.00 Nos.

22

55

Sorround SITC of Cinema Surround Loudspeaker, 2-Way Passive 1" HF, 10" Woofer (2" VC) Frequency Range (-10 dB) 50Hz – 25kHz (2π) / 60Hz – 25kHz (4π), Frequency Range (±3 dB) 60Hz – 20kHz (2π) / 100Hz – 20kHz (4π),Coverage Pattern 110º × 60º asymmetric >2kHz, Power Handling 30v @ 100hrs, 40v @ 2hrs, IEC/Pink 250W continuous pink noise, Sensitivity 96dB SPL @ 2.83v, Maximum dB SPL 120 dB continuous, 126 dB peak, Rated Impedance 8 Ω, Minimum Impedance 7Ω @ 200Hz, Crossover Frequencies 2800Hz, Low Frequency 610H, High Frequency 2414H-1 Approved Makes: JBL, QSC, Tanoy, Bose or equivalent

22.00 Nos.

56 SITC of Mounting Brackets 22.00 Nos.

57

Four CH Amplifier SITC of Four channel 600W@4Ohm Amplifier : Frequency Response ( 8 Ohms, 20 Hz - 20 kHz) +/- 0.25 dB, BLU Link Input Signal to Noise Ratio (A-Weighted) > 104dB, Total Harmonic Distortion (at full rated power, 20 Hz - 20 kHz) 0.35%, Voltage Gain 34 dB, Damping Factor (20 Hz to 100 Hz) >1000, Input Impedance (nominal balanced, unbalanced) 10 kOhms, 5 kOhms, Maximum Input Level before Compression +20 dBu, Load Impedance (Stereo/Dual Mode) 2 - 16 Ohms; 70Vrms and 100Vrms, Load Impedance Bridge Mono 4 - 16 Ohms; 140Vrms and 200Vrms Approved Makes: Crown, QSC, Powersoft.

1.00 Nos.

58

Dual CH Amplifier SITC of Dual channel 600W@4Ohm Amplifier : Frequency Response ( 8 Ohms, 20 Hz - 20 kHz) +/- 0.25 dB, BLU Link Input Signal to Noise Ratio (A-Weighted) > 104dB, Total Harmonic Distortion (at full rated power, 20 Hz - 20 kHz) 0.35%, Voltage Gain 34 dB, Damping Factor (20 Hz to 100 Hz) >1000, Input Impedance (nominal balanced, unbalanced) 10 kOhms, 5 kOhms, Maximum Input Level before Compression +20 dBu, Load Impedance (Stereo/Dual Mode) 2 - 16 Ohms; 70Vrms and 100Vrms, Load Impedance Bridge Mono 4 - 16 Ohms; 140Vrms and 200Vrms Approved Makes: Crown, QSC, Powersoft.

1.00 Nos.

23

59

Speaker Cable SITC of Compact Indoor Outdoor Background Foreground Loudspeaker: Frequency Range 70 Hz - 23 kHz (-10 dB), Power Capacity 200 W Continuous Program Power; 100 W Continuous Pink Noise, Transformer Taps 70V: 60 W, 30 W, 15 W, 7.5 W , 100V: 60 W, 30 W, 15 W, Nominal Sensitivity 87 dB SPL, 1 W @ 1 m (3.3 ft), Midrange (±1.5 dB, typical) 130 Hz - 14 kHz, Nominal Coverage 100° x 100°, Maximum SPL @ 1m 113 dB continuous peak pink noise 107 dB continuous average pink noise 103 dB continuous average music or speech, Directivity Factor (Q) 4.9 dB, averaged 500 Hz to 4 kHz, Directivity Index (DI) 6.9 dB, averaged 500 Hz to 4 kHz, Nominal Impedance 8 ohms, Minimum Impedance 6.7 ohms at 230 Hz Approved Makes: JBL, QSC, Tanoy.

6.00 Nos.

60

Dual CH Amplifier SITC of Dual channel 120W@4Ohm Amplifier: Power Output 120W Output Channels 2, Input Sensitivity 1.4Vrms for 8-ohms, Phantom Power 27VDC, AC Line Voltage 100 - 240V, 50/60 Hz, Input Impedance 20K ohms/50K ohms Approved Makes: Crown, QSC, Powersoft.

2.00 Nos.

61

Volume Controller SITC of Volume Controller Ethernet Wall Controller Compatible with BSS Audio Soundweb London, Crown DCi, and other HiQnet devices, Available in Black or White, Available in US Decora or EU Version, Single-Gang Size, PoE (Power Over Ethernet), Configured within Audio Architect via Drag-and-Drop, 1 Programmable Push/Rotary Encoder, 1 Programmable Encoder Ring (Multicolor), Approved Makes: JBL, QSC, Tanoy, Bose or equivalent

3.00 Nos.

24

62

Lectern SITC of Lectern with CPU & Monitor 19" Full HD 1080p Projected Capacitive Touch Monitor , Controller cum Switcher and Mixer 12 Keys on Touch Pad - The system Support for one key class on, one key class off, one key control the projector, a function key to turn off the projector, control electric ,screen lift, volume, Laptop Interface VGA, HDMI, USB & Power (1 Each), Inbuilt DSP for echocancellation and Noise reduction, i3 Codec with Lic Windows - 4GB RAM , 500GB storage

1.00 Nos.

63

Speaker Cable SITC of 1 Pair: 16 AWG Speaker Bulk Cable,Conductors: (26/30) bare copper conductors ,Center Conductor: 1.478mm (0.058in), DC Resistance: 13.7Ω/km (4.17Ω/1000ft), UL: CM CSA: CM, CSA: FT4, RoHS: In compliance with European directive 2002/95/IEC Kramer/Belden/ Panduit make

1000.00 Mtrs.

64

Audio Cable SITC of 1 Shielded Pair: 20 AWG Audio or Control Bulk Cable,Conductors: (10/30) tinned copper conductors, Conductor: 0.916mm (0.036in),Impedance: 40 to 100Ω, DC Resistance: 34.6Ω/km (10.5Ω/1000ft), UL: CL−2, CSA: C(UL) FT4, RoHS: In compliance with European directive 2002/95/IEC Kramer/Belden/ Panduit make

300.00 Mtrs.

25

65

DLP Laser Projector SITC of 10000lm DLP™ chip Laser Projector with Panel size:17.0 mm (0.67 in) diagonal (16:10 aspect ratio), Display method:DLP™ chip × 1, DLP™ system, Pixels:2,304,000 (1920 × 1200) × 1, total of 1,024,000 pixel s, Lens:Optional powered zoom/focus lenses, Light Source:Laser Diode Laser class 1(Class3R for US models), Center-to-corner uniformity:0.9, Contrast :10,000:1 (All White/All Black) (Dynamic Contrast3), Resolution:1920 × 1200 pixels, Optical axis shift Vertical:Vertical: +50%, -16%(powered),Horizontal:Horizontal: +30%, -10%(When using the ET-DLE085, +28%, -10) (powered), DIGITAL LINK / LAN:RJ-45 Network connection / digital link connection (video/network/serial, control) compliant with PJLink (class1) ,100base-tx, Art-Net compatibleApproved Make: Sony , Panasonic, Cisco

1.00 Nos.

66

Projector Screen SITC of High Gain Projection Screen with 278"Diagonal 16:10Aspect Ratio ; 147 1/2"x 236" Screen with LVC for Controlling and RF remote. Approved makes: Dalite, Draper, Steward.

1.00 Nos.

67 Projector Mounting KIT SITC of Heavy duty Ceiling mount kit for above Projector. Approved Makes : Custom

1.00 Nos.

26

68

SITC of 1000W CE Certified halogen Fresnel spot light providing illumination of 28000 lix at 2 mt in spot at 10° beam angle while 4600 lix at 2 mt when operated in flood at 48° beam angle , dimension as 290 x 405 x 290mm, 150mm aid German lens, weight of 4.6Kg, Gx9.5 base lamp socket,power cord with 16amps 3 pin CE plug and normal yoke but without lamp and accessories. Lamp -1000W 230V single ended lamp Power supply - 230-240V AC,Lamp Socket - Gx9.5Power cable - 3 core 1.5 sq. mm. copper PVC insulated,Housing - Light weight, rugged and reliable both indoor and outdoor,Robust per-treated fabricated housing with die cast component and epoxy polyester powder coated,Distribution - Delivers smooth uniform field across the entire spread from spot to flood focusing,Switching options - Local control and Digital DMX control through Dimmer,Dimming option - Digital DMX control through Dimmer,Reflector - Spherical high reflective aluminum anodized,Yoke - Fabricated using MS flat-accepts mounting on 16mm spud,Focus - controlled by front & rear thermoplastic knob. Make: Desisti / ARRI / Canara lighting.

16.00 Nos.

27

70

SITC of 1000W CE certified spun aluminum PARCAN providing illumination of 48188 lux at 2 mt in spot while 18500 lux at 2 mt when operated in flood made out of spun aluminum 16 SWG in 2 piece cylindrical construction with punched slot on Par can housing for natural ventilation and floating ceramic GX16d base lamp socket,copper flexible PVC insulated power cable with 3 pin CEE plug, Yoke made of MS flat 25 X 3mm with 13mm free mounting hole to fit the adapter, spigot with 28mm and filter frame but without lamp. "Lamp: 1000W 240V PAR-64,Lamp Socket: Ceramic type GX 16D.Power Cable: 3 core,1 Squirm copper PVC insulated flexible cable with 10 amps double pole toggle switch,Housing: Aluminum sheet cylindrical construction with black epoxy polyester powder coated","Switching options: Local control and Digital DMX control through Dimmer,Dimming option: Digital DMX control through Dimmer,Yoke: Fabricated using MS flat- accepts mounting on 28mm spud Focus: Sealed beam angle,Accessories: Filter frame. Make: Desisti / ARRI / Canara lighting.

30.00 Nos.

71

54x3W CE certified LED Par with CCT 3200K,12310 lux level at 2mtr, 54 LED's each should be at warm color temperature of 3200K, back LED display, CRI Value above 85, Self dimming option from 0-100%, 5 Pin Dmx XLR for mix dimming operation but without any accessories, loop in loop out option undergone through 7 Tank chemical treatement to keep them rust free and, duly powder coated in black matt texture finish and technical specifications as below. • Lamp - 54 x 3W 3200K LED, • Power consumption – 160W, Power supply - 230/240V AC, • Power cable - 3 core 1.5 sq. mm. copper PVC insulated, • Channels - 1 Channel DMX-512, Beam angle - 25° (15°, 45° optional) • Lux level – 12310 at 2 mtr • Control mode - DMX through5 pin male and female, Manual. Function - Manual dimming, DmX modes of operation. Make: Robe / Martin / Canara lighting.

10.00 Nos.

28

72

SITC of 3x54W LED par light complete with 8-channel DMX 512, high brightness mixing color evenly, stable performance with sound active auto, DMX, and power and DMX loop in and out option, undergone through 7 Tank chemical treatement to keep them rust free and, duly powder coated in black matt texture finish and technical specifications as below. • Lamp - 54 X 3W RGB LED (12R+18G+18B+6W) • Power consumpsion - 150W • Power supply - 230/240V AC • Power cable - 3 core 1.5 sq. mm. copper PVC insulated • Channels - 8 Channel DMX-512 • Beam angle - 25° (15°, 45° optional) • Control mode - DMX, and Manual. • Function - strobe, Dimming, sound active.Make: Robe / Martin / Canara lighting.

20.00 Nos.

73

SITC of 750W stage profile spot light powder coated diecast body with below specification • Lamp 750W HPL • Beam spread 19° • Dimension of 560 x 340 x 430mm • Weighing 6.2Kg, • Dichroic reflector, • G9.5 lamp base • 4 Beam shaping shutters • 3mtrs power cord with 16amps CE plug • Normal yoke with adjustable keys for tilt rotation • Fine adjustment in lamp focus position for adjustment Make: Spotlight / LDR / Canara lighting.

12.00 Nos.

74

SITC of 4X100 W LED Colour corrected Effect/Flood light 2 in 1 fixture 3200K with advanced COB LED technology made of MS house black paint finish with IP 20 rating of Voltage AC100V-240V, • Frequency: 50-60Hz, • Power Consumption: 260W, • LED Power: 200W, • Color Rendering Index(CRI):≥90, • LED Lifetime: Over 50,000 hours, • Control Mode: DMX • DMX Channel: 2/5CH Dimmer: 0~100%, • Beam Angle:30° • Control mode: DMX 512, mater and slave, auto running sound mode. Make: Canara Lighting / Selecon / Robe.

10.00 Nos.

75 SITC of Diecast aluminium "C" clamp with safety pin. SWL 100 Kgs. Make : Canara Lighting / ARRI / Desisti.

98.00 Nos.

29

76

SITC of Safety bond with lock clip to be fixed around the grid and each lighting fixture to avoid fall of the fixture in case if the "C" clamp is not locked properly . SWL 100Kgs. Make : Canara Lighting / ARRI / Desisti.

98.00 Nos.

77 SITC of 1000W 230V single ended halogen lamp CP24 / CP70 Base Gx9.5.t Make: Philips / Osram / GE./ canara

16.00 Nos.

78 SITC of 1000W 230V Par-64 narrow / medium / wide lamps with base Gx16d for 1kW Halogen parcans. Make: Philips / Osram / GE.

30.00 Nos.

79 SITC of 750W HPL 230V lamps G9.5 Base for profile spot light and 19° stage profile spot light Make: Philips / Osram / GE.

12.00 Nos.

80

SITC of Digital Dimming system consists of Controller for the LED lights & Halogen Lights : - 1. 96 Channel DmX controller. 2. 12 channel rack mount dimmer 3. Splitter for the Light dimming network. 4. DmX Cables and XLR connectors. Aproved make: Desisti / ARRI / Canara lighting.

1.00 Lot.

81 SITC special lighting in Atrium/ Foyer area 25.00 Lot.

82 SITC special column bracket lights in AUDITORIUM 18.00 Nos.

83

SWITCHING CONTROLS - Wall Plate SITC of Passive Wall Plate — 15–pin HD, 3.5mm Audio & HDMI, Computer Graphics Video, HDMI & Stereo Audio Passive Wall Plate Size — Wall Plate — 1 gang European or US. Audio — U, Kramer/Crestron/Extron make

1.00 Nos.

30

84

SWITCHING CONTROLS - Presentation Switcher SITC of 11x4:2 Presentation Boardroom Router / Scaler System with INPUTS : 6 HDMI connectors, 1 VGA on a 15–pin HD connector, 4 HDBT on RJ–45 connectors, 4 USB ports, 6 unbalanced analog audio on 3.5mm mini jacks for HDMI, 1 unbalanced analog audio on a 3.5mm mini jack for PC, 1 aux in/mic balanced stereo audio on a 5–pin terminal block connector OUTPUTS: 4 HDBT on RJ–45 connectors, 4 HDMI connectors, 1 USB port, 4 audio out balanced stereo on 5–pin terminal block connectors, 4 audio out S/PDIF on RCA connectors, monitor out balanced stereo on a 5–pin terminal block connector, monitor out S/PDIF on an RCA connector.,1 stereo speaker output, 2x10W into 4Ω, on a 4–pin terminal block connector Kramer/Crestron/Extron make

1.00 Nos.

85

Wall Plate Transmitter SITC of 4K60 4:2:0 HDMI & VGA Step–In PoE Wall–Plate Transmitter with Ethernet, RS–232 & Stereo Audio over Extended–Reach HDBaseT Max. Data Rate — 10.2Gbps (3.4Gbps per graphic channel), Resolution Support up to 4K@60Hz (4:2:0), Automatic Live Input Detection Automatic Input Selection, I–EDIDPro™ Kramer Intelligent EDID Processing™, Kramer Equalization & re–Klocking™ Technology Range — Up to 100m in normal mode, Control — Ethernet and embedded Web pages over RS–232., Digital Audio Format Support. Audio — U/E with Kramer/Crestron/Extron make

2.00 Nos.

86

Reciever SITC of 4K60 4:2:0 HDMI HDCP 2.2 Receiver with RS–232 & IR over Long–Reach HDBaseT with HDBaseT 1.0 receiver, Long–reach — Up to 40m (130ft) at 4K@60Hz (4:2:0), Video resolution — Up to 4K@60Hz (4:2:0) 24bpp, Control extension, Size — DigiTOOLS® — Mount 3 units side–by–side in a 1U rack space with the optional RK–3T rack adapter. ,Audio — E Kramer/Crestron/Extron make

2.00 Nos.

31

87

Control Brain SITC of 32–Port Master Room Controller with BIDIRECTIONAL PORTS: 8 RS–232 serial on 3–pin terminal blocks, 8 GPI/O on 2–pin terminal blocks, 1 Ethernet on a RJ–45 connector, 1 mini–USB connector for firmware upgrade, INPUTS : 1 built–in IR sensor (for learning), OUTPUTS : 8 IR out and 8 relays on 2–pin terminal block connectors, INDICATORS : LED indicator for each port and function PROCESSOR SPEED: 1GHz MEMORY : 512MB RAM, 4GB Flash Kramer/Crestron/Extron make

1.00 Nos.

88

Control Keypad SITC of 6–button Ethernet and KNET™ Control Keypad (EU, UK, US–D) with 6 RGB–color, backlit buttons, Custom labeled, removable button caps, 1 Ethernet port, 1 KNET™ port, 1 RS–485 port, 2 Bidirectional RS–232 ports, 2 IR emitter ports, 1 GPI/O port, 2 Relay ports, 1 IR sensor for learning, Site–CTRL™ software compatible , INPUTS : 1 RS–485, 2 RS–232, 1 GPI/O, 1 K–NET on terminal block connectors, 1 Ethernet on an RJ–45 connector, 1 infrared sensor, 1 mini USB for programming. OUTPUTS: 2 IR emitter, 2 relays (36V AC or DC, 2A, 60V AC maximum on non–inductive load) on terminal block connectors Kramer/Crestron/Extron make

1.00 Nos.

89

Control/Expansion Gateway SITC of RS-232,IR and relay control gateway(expansion module) 4–Port Multi–Function Serial/IR & GPIO/Relay PoE Control Gateway with PORTS : 2 RS–232/IR multi–function ports on 3–pin terminal blocks each selectable as either 1 bidirectional RS–232 (RS–485 port 1 selectable option) serial or 2 IR emitter ports, 2 GPIO/Relay multi–function ports on 3–pin terminal blocks each selectable as either 2 GPI/O or 2 relay ports, 1 LAN on an RJ–45 female connector, 1 built–in IR sensor for IR learning, 1 mini USB connector for local services Kramer/Crestron/Extron make

2.00 Nos.

32

90

HDMI Cable SITC of High Speed and Standard Speed 6ft HDMI cables, HDMI cables support the following resolutions: 480i, 480p, 720p, 1080i, 1080p, CONDUCTOR AWG : 28 AWG (7/0.127), SHIELD : Dual shield against EMI/RFI interference, (a) Al− Mylar, (b) Tinned Copper, CABLE OD (MM): 7.3, Kramer/Crestron/Extron make

5.00 Nos.

91

HDMI Cable SITC of High Speed and Standard Speed 15ft HDMI cables, HDMI cables support the following resolutions: 480i, 480p, 720p, 1080i, 1080p, CONDUCTOR AWG : 28 AWG (7/0.127), SHIELD : Dual shield against EMI/RFI interference, (a) Al− Mylar, (b) Tinned Copper, CABLE OD (MM): 7.3, Kramer/Crestron/Extron make

4.00 Nos.

92

VGA with Audio cable SITC of 25 ft VGA cable with Audio ( 15-pin HD to 15-pin HD Cables ), Conductor: 26AWG 7/34 tinned copper, Shield: (A) 90% spiral 38AWG tinned copper (B) aluminum−foil/Mylar 25% overlap rate, Impedance: 75Ω, UL: CL2 CSA: C(UL) CL2 Kramer/Crestron/Extron make

1.00 Nos.

93

VGA with Audio cable SITC of 6 ft VGA cable with Audio ( 15-pin HD to 15-pin HD Cables ), Conductor: 26AWG 7/34 tinned copper, Shield: (A) 90% spiral 38AWG tinned copper (B) aluminum−foil/Mylar 25% overlap rate, Impedance: 75Ω, UL: CL2 CSA: C(UL) CL2 Kramer/Crestron/Extron make

4.00 Nos.

94

DGKat Cable SITC of CAT6A U/FTP Video & LAN Bulk Cable — Low Smoke & Halogen Free,Lengths — 305m (1000ft) Low Smoke & Halogen Free, Audio — N/A

1.00 Nos.

95 Audio Cable SITC of 3.5mm Stereo Audio Cable, Lengths — 6ft (1.8m) Audio — U Kramer/Crestron/Extron make

2.00 Nos.

33

96

RACK SITC of 42U equipment rack, Power Distribution Unit - 06 Amp - 07 Socket Castor with brake and with out brake Cable manager Shelves Monitor Tray - Ventilation with Front and back doors Fan assembly Approved Make - Rittal,President,Middle Atlantic

1.00 Nos.

97

3MP Bullet Camera SITC of 3MP CCTV Bullet camera - 1/3" progressive scan "Exmor" Mega-pixel CMOS sensor, Effective Pixels 2048 (H) x 1536 (V), Lens Type 3.6/4/6 mm Fixed, F1.6, Video Bit Rate 1280K ~ 8192 Kbps @ 1080p, supports 3 codecs ( H.264, MPEG-4 & JPEG, Day & Night function, Power over Ethernet (P oE),Video Information Channel as title; time title; motion detection; privacy mask, IR Beam Distance Max. 30m ,Ingress Protection : IP66 per enclosed specifications Make: Honeywell / BOSCH / AXIS

22.00

Nos.

98

32Ch NVR SITC of Network Video Recorder cum management surver to Supports 32 channels (In Single/ multiple Units), of 720p/1080 resolution full framed real time Video recording & capable of 24 x 7 video recording with internal storage unit upto 32 TB or suitable configuration to have as per specification attached complete as required Enterprise- class client /server based video management system from same camera OEM ( expandable), superior alarm handing with alarm priorities complete as required for live and playback complete as required. The software as per the OEM of the cameras and VMS + NVR shall be acceptable Make- Honeywell / BOSCH / AXIS

1.00

Nos.

99 Hard disk SITC of 4TB survillance HDD Make : WD, Segate, Toshiba

4.00 Nos.

34

100

24Port POE switch SITC of Layer 2, 24 Port ,POE, Gigabit, Network Switch with 2 Nos. single Mode Fiber Port. complete as required as per specification. Make:- Cisco/HP/Netgear

1.00 Nos.

101

RACK for NVR SITC of 19" Wall mount Rack of 9U for housing Field Network Switch & NVR complete with from door, power distribution Panel, Fiber splice tray / Box , etc as required as per specification Make:- Elixer, APW, Vall rack

1.00 Nos.

102

LED Display for Viewing SITC of Wall mount 43" HD Commercial LED Display having 2 HDMI port with wall mount accessories (Industrial/Commerical Grade Only) Make: Pansonic/Samsung/LG

1.00 Nos.

103 SITC of CAT 6 UTP cable, Make : Dlink/ R&M/ Tyco 2000.00 Mts.