om1 papercraft m e

Copyright 2008 OLYMPUS CORPORATION All Rights Reserved.

Paper Craft Assembly Manual

Before assembly:

Print all the parts (Photo-quality paper is recommended for ink-jet printers and paper of medium thickness (0.20 mm) for laser printers.)

Print this manual. Prepare the following:Scissors,Hobby knife (cutting blade), Ruler, Tweezers,Pointed

tool (e.g., used ballpoint pen, stylus, awl),Glue for wood or paper craft,Marker,Desk pad for craft making.

Explanations on lines and symbols:

{ } Cut along the line.

{ } Mountain fold (Fold along the line. The printed surface should be on the outside of the folded shape.)

{ } Valley fold (Fold along the line. The printed surface should be on the inside of the folded shape.)

{ } Cut out the shaded area.

{ } Sections with red dots are margins for gluing or gluing surfaces.

{ } When gluing one section to another section, align the edges of that part with the dotted lines.

Tips on assembly:

1 ) Before detaching parts from the sheets, first use a used ballpoint pen, a stylus or other pointed tool to make a light crease along the folding lines, to make it easier to fold neatly later on.

2 ) To remove the parts from the printed sheet, cut carefully along the outer edge of the solid lines.

3 ) It is useful to gently write a number on the back of each part for easier identification later on.

4 ) When cutting a straight line, try to draw the paper toward you as you cut, rather than moving your scissors away from you; this will produce a cleaner cut. If you use a hobby knife, put a pad underneath to protect the desk surface and use a ruler.

5 ) Similarly, try to hold the scissors steady and rotate the paper as you cut rounded parts for a better cut.

6 ) Each part should be gently bent for easier gluing and accurate assembly.

7 ) When folding along a straight line, it is best to use a ruler.

8 ) For the lens and other contoured parts, the section should be rubbed against the corner of a desk or other rounded surface to give them a natural curve before gluing.

9 ) A number of fine parts are involved in the assembly. The key is to let the adhesive dry adequately. Also, be careful not to blot the parts with glue remaining on your fingers.

10 ) If you use glue for wood craft, spread the adhesive on a piece of paper first, then use a strip of thick paper to scoop the adhesive and apply a thin layer of adhesive over the glue margins.

11 ) Hold the parts firmly until the glue becomes dry.

12 ) Assemble each part first before putting all parts together for final assembly of the entire model.


Note on printing

When printing the file with Adobe Reader, make

sure to switch from Shrink to Printable Area

(default) to None under the Page Scaling heading,

which appears in the Print dialog box (see the

diagram on the right), to create a model scaled to

the actual size.

Click here and choose None.

OM-1 Paper Craft Assembly Manual 1 / 9

* Unless instructed otherwise in the manual, the partsshould bemountain folded so that the printed surface will be on the outside of the folded shape.

z1 ) First, assemble the main body only halfway through. 2 ) Mounting the film advance lever

3 ) Positioning of the film advance lever

4 ) Complete the main body after mountingthe film advance lever.

y

y-2y-3

y-1

y-5

Put together y-4s

y-2 must be attached to y sothat y-3 becomes parallel tothe main body when y is rotatedfully clockwise (Position A).

Parallel to each other

Find a position where y-3 becomes parallelto the main body (Position B) as you rotate ycounterclockwise, then glue y-2 to y.

The surface marked with @ must face down.

Cross-sectional view showingthe relationship between y and z

y-1

y-4

z

y

y-5 z-1

y-3 y-2y

y

Use z-1 to reinforce the hole.

The back of the body

Inner mechanism:

A B The lever moves.

Copyright 2008 OLYMPUS CORPORATION All Rights Reserved. 2 / 9OM-1 Paper Craft Assembly Manual

I. Assembly of the main body

* *

u

uu

3 ) 4 )

1 )

5 )

2 )

v

The printed surface must face inside.

Glue the sections indicated byarrows so that the glue marginsare on the outside.

Glue u on the back of u-1.

Pay special attention to theposition of * when gluing.

Glue margin of v

Glue v and u together (cross-sectional drawing)

Glue 2 v-1 s on the back of v.

u-1

v-1v

v

Glue margin

Glue margin

u-1

u

Glue margin of v

u

u-1

v-1

*

Make sure the surfacesmarked by * of u-1 and v arealigned when glued together.

v-1* *


II. Assembly of the lens mount section

*

Assembly of the apron (x) 2 )1 ) Assembly of the pentaprism (w)

Please go to Pages 7 and 8 for the assembly of c, d and g.

The surface with printedaperture settings should face up.

w

x

u+v

g

g

c d


III. Assembly of the main body (Part 2)

l-1 l l-2 l-3

m

r s t

m

n

n

The body ofthe lens (l)

o pq q-1 q-1 q-2

o

Aligning m, n and o:

3 ) 4 )

2 )1 )

Valley fold

Glue r and s together byaligning their seams.

View from the back

Starting fromthe seam of l, glue m, n and oby windingthem around l.

l-2 should be positioned on the coloredglue margins of l. l-2 should be attachedso that it bisects l in half.

This markingshould be alignedwith the seam of l.

l-2

l


IV. Assembly of the lens

aaHinge

kView finder eyepiece framea

Self-timer lever

eShoulder strap eyelet

dFlash

Synchronizationsocket

fMater

switch lever

b Rewindreleaselever

gShutter speed

ring knobsiRewindrelease lever

jASA film speed dial

hShutter release

button

abHinge

6 / 9Copyright 2008 OLYMPUS CORPORATION All Rights Reserved.

The small parts listed on Pages 7 and 9 (a, b, c, d, e, f, g, h, i, j, aa, ab) require more intricate work.These parts may be skipped as they are printed on the main body.

cMirror

lock-uplever

OM-1 Paper Craft Assembly Manual

V. Assembly of smaller parts

ff

f-1

f-2

Valley foldValley fold

e

2

b

b-1 c-2c-2c-1

c

a

a-1

a-2a-2

a

d

b c

Mater switch leverShoulder strap eyelet

Self-timer lever

Flash Synchronization socket

Rewind release lever Mirror lock-up lever

Valley fold


VI. Assembly of smaller parts (Part 2)

2

kk

k-1

k-2

k-3

j-1h-1

Printed surface should face k.

Surface with illustration

aa is the longer one; ab is the shorter one.

aa

ab

i-1


g Shutter speed ring knobs

k View finder eyepiece frame aa and ab Hinges

h Shutter release button i Rewind release lever j ASA film speed dial

8 / 9OM-1 Paper Craft Assembly Manual

VII. Assembly of smaller parts (Part 3)

VIII. Putting them all together

h

b

a

ab

aa

if

kj

w

e

e


Get the body parts for the M-1 by filling out our online survey.You can re-create the legendary M-1, the original model fromwhich the OM series descended, by downloadingthe M-1 body parts and combining them with the partsfor the OM-1Please download the file by filling out the survey.

All parts except for the main body are identical with the OM-1 model.

The assembly of the M-1 body is exactly the same as the assembly of the OM-1 model

Copyright 2008 OLYMPUS CORPORATION All Rights Reserved.OM-1 Paper Craft Assembly Manual

SPECIAL

Yes. I want to fill out the questionnaireand download the M-1 body parts!

https://support.olympus.co.jp/cf_secure/en/enquete_form/00264DDB25825D0842AAAC0447FE848283301634

Free M-1 Body Parts !

om-1 Assembly ManualH1.aiom-1 Assembly Manual00.aiom-1 Assembly Manual01.aiom-1 Assembly Manual02.aiom-1 Assembly Manual03.aiom-1 Assembly Manual04.aiom-1 Assembly Manual05.aiom-1 Assembly Manual06.aiom-1 Assembly Manual07.aiom-1 Assembly Manual08.aiom-1 Assembly Manual09.ai

om1 papercraft m e

Documents