oil & gas · - easy-laser® e960 turbine measuring and aligning bearings and bearing journals....
TRANSCRIPT
OIL & GASMARINEPOWER
Pressure Systems & ComponentsFlow EquipmentAlignment SystemsOil-In Water Monitors-AnalyzersOil Filtration SystemsOn-Site Machines
SalesRepairDesignFabricationRentalTraining
High Pressure Hoses Low Pressure Hoses- Hydrostartic Testing- Methanol Injection- Chemical Injection- Nitrogen Service- Wells & BOP’s - Hydraulic Controls - Workover Umbilicals- High Pressure Cement Hoses- High Pressure Choke & Kill Hoses- Control Line Jumps & Tensioning Equipment
Pressure Components, Systems
Air Driven Liquid Pumps + Gas Booters + Air Amplifiers Injection Pumps
Valves, Fittings, Couplings, Tubing (0-60k PSI)
Pressure Testing Systems & Control Systems Gas Transfer Systems
Test Bay Unit WorkshopTest Cabinet
Gas Booter Unit to 30k PSI
Nitrogen Charging Unit
for Accumulators
Chart Recorders
Pressure Gauges
High & LowPressure Gauges
Dead WeightTesters
Quick Couplings
Fittings
Manifolds
Valves, fittings &tubing to 150,000PSI
DBB Valves Needle ValvesBall Valves
Compression Fittings
Dual Pump ControlPanel 0-20k PSI
Flange
4 WARRANTY PERIODPDF Report
IP66/IP67
Shaft Alignment Systems- Easy-Laser® E710, E540, E420Alignment system for rotating machines.- Shaft Alignment- Measure bearing play - Measure base flatness - Measure vibration(ATEX/Ex)
Belt Alignment - Easy-Laser® E180 Offers a wide range of tools for quick and easy alignment of sheaves/pulleys. Suitable for most types of drive: V-belt, timing belt, flat belt and chain drives.
Geometric Measurement- Easy-Laser® E920 For measurement of straightness, flatness, squareness etc.- Easy-Laser® E950 Bore AlignmentMeasuring and aligning bearings and bearing journals. For Diesel engines, Compressors, Gearboxes etc. For Propeller shaft drive lines with sterntube.- Easy-Laser® E960 Turbine Measuring and aligning bearings and bearing journals. Turbine diapraghms and bearing. For gas turbines and smaller steam turbines.For large turbines.
Precision Laser Alignment
Mounting and Dismounting of Bearings and Transmission PartsImprove the quality of maintenance and installation of rotating parts- Heaters, Standard & TURBO models- Hydraulic pullers 4-50 t cap., self-centering. Accessory sets- Fitting tools: for safe mounting of bearings, rings, seals, etc.- Cylinders: single acting, double acting, low height, hollow, spring or load return, aluminium, 700 bar, up to 1000t
Hydraulic PullersBearings BeltsFitting Tools Heaters
Bearings, Mechanical Seals, BeltsBesides, we also provide replaceable spare parts: all kinds of bearing (FAG, NSK, IKO,… ), Meachanical seals (NOK,…), Belt (Optibelt,…),…
Shaft Alignment Line BoreTurbine
E710
E950
Fluorescence TechnologyLow operating cost
IP67
Measuring and monitoring hydrocarbons in waterPortable Analyzers: TD-500D - The WORLD’S BEST hand held Oil in Water Analyzer- Oil and grease analysis in less than 4 minutes- No solvent evaporation- Minimum detection limit: < 1ppm for most crude oils- Meets IP67, dust-proof, waterproof, non-metallic case
Bench for Analyzers: TD-3100 - Measure samples directly (non-extraction)- Less than 10 seconds per sample- Un-calibrated method for relative measurementsDetection limits range from ppb to ppm depending on application
On-line Monitors: TD-4100, TD-4100XD, TD-4100XDC,…- Designed specifically for offshore oil production, refining, pet-ro-chemical, mining, and other industries that require robust on-line hardware for severe duty and hazardous area locations.- Detects and measures crude oil, refined fuels, fuel oils, lubricat-ing or hydraulic fluids and aromatic solvents in water. Detection limits range from low ppb (µg/L) to high ppm (mg/L).
Oil-In Water Monitoring Systems
Solvent or No solvent Analyzers
TD-4100 XDMonitors
Piston Pumps Diaphragm PumpsDrum Pumps
TD-3100Analyzer
TD-500Analyzer
TURNER DESIGNSHydrocarbon Instruments
- Air Operated Double Diaphragm Pumps- Drum Pumps- High Pressure Piston Pumps- Paint Spraying Systems- Api Centrifugal Pumps- Pump Parts
Flow Equipment
Mactech onsite machine tools for ship building and ship repair.Application: Heat Exchangers. Man way seals. Anchor winch mounts. Boring rudder pins. Boring stern tubes. Valve repair. Crane mounts. Motor and generator pads.
Mactech onsite machine tools for the oil and gas industry.Application: Line boring. Flange re-facing. 3 axis milling. Valve seat machining. Key milling. Shaft turning. Pipe beveling. Spot facing. Pipe cutting. Stud removal. Bore welding. Drilling and tapping.
On-Site+Subsea Machine Tools
Line Bore System 3-Axis MillClamshell Lathe End Preparation Lathe
The CJC™ Filter System is used for oil maintenance. It is generally used as an off-line filtration system in continuous operation.
Applying a CJC™ Filter System to your system will give you the benefit of increased uptime for production machinery and extended service life for system components, by effectively reduc-ing oil contamination from:- Insoluble particles.- Oil degradation products and oxidation by-products.- Water.
Solutions for removal of particles, absorption of water, adsorption of oxidation by products and varnish from oils.
Solutions for removal of water from low and high viscosity oils, even in stable emulsions.
Oil Filtration Systems
Hydraulic Cranes
BOP & Riser
Thrusters
DieselEngines
Top Drive
Drawworks
Mud Pumps
Winches
Turbines
HPUMarine
Power