ocmos fet ps7142-1b,-2b,ps7142l-1b,-2b › pdf › datasheets › ps71421b.pdf · the ps7142-1b,...

6, 8-PIN DIP, 400 V BREAK DOWN VOLTAGE NORMALLY CLOSE TYPE

1-ch, 2-ch Optical Coupled MOS FET

Solid State RelayOCMOS FET

PS7142-1B,-2B,PS7142L-1B,-2B

−NEPOC Series−

DESCRIPTION

The PS7142-1B, -2B and PS7142L-1B, -2B are solid state relays containing GaAs LEDs on the light emitting side (input side) and normally close (N.C.) contact MOS FETs on the output side.

They are suitable for analog signal control because of their low offset and high linearity. The PS7142L-1B, -2B have a surface mount type lead.

FEATURES • 1 channel type (1 b output) or 2 channel type (1 b + 1 b output) • Low LED operating current (IF = 2 mA) • Designed for AC/DC switching line changer • Small package (6, 8-pin DIP) • Low offset voltage • Ordering number of taping product : PS7142L-1B-E3, E4: 1 000 pcs/reel : PS7142L-2B-E3, E4: 1 000 pcs/reel

<R> • Pb-Free product <R> • Safety standards

• UL approved: File No. E72422 • BSI approved: No. 8245/8246 • CSA approved: No. CA 101391

APPLICATIONS • Exchange equipment • Measurement equipment • FA/OA equipment

The mark <R> shows major revised points. The revised points can be easily searched by copying an "<R>" in the PDF file and specifying it in the "Find what:" field.

Document No. PN10285EJ02V0DS (2nd edition) Date Published July 2006 NS CP(K) 1998, 2006

DISCO

NTINUED

PS7142-1B,-2B,PS7142L-1B,-2B

PACKAGE DIMENSIONS (in millimeters)

9.25±0.5

3.5±

0.3

4.15

±0.

33.

3±0.

3

0.5±0.12.541.34±0.1

0.25 M

0 to 15˚

7.62

6.5±0.5

9.25±0.5

3.5±

0.3

1.34±0.10.25 M

2.54

6.5±0.5

0.10

+0.

10–0

.05

0.9±0.25

9.60±0.4

9.25±0.5

3.5±

0.3

4.15

±0.

33.

3±0.

3

0.5±0.1

2.541.34±0.10.25 M

0 to 15˚

7.62

6.5±0.5

9.25±0.5

3.5±

0.3

1.34±0.10.25 M

2.54

6.5±0.5

0.10

+0.

10–0

.05

0.9±0.25

9.60±0.4

PS7142-1B PS7142L-1B

PS7142-2B PS7142L-2B

1 2 43

6 58 7

TOP VIEW

1. LED Anode2. LED Cathode3. LED Anode4. LED Cathode

5. MOS FET6. MOS FET7. MOS FET8. MOS FET

1 2 43

6 58 7

1. LED Anode2. LED Cathode3. LED Anode4. LED Cathode

5. MOS FET6. MOS FET7. MOS FET8. MOS FET

TOP VIEW

1. LED Anode2. LED Cathode3. NC4. MOS FET Drain5. MOS FET Source6. MOS FET Drain

1 2 3

6 5 4TOP VIEW

1. LED Anode2. LED Cathode3. NC4. MOS FET Drain5. MOS FET Source6. MOS FET Drain

1 2 3

6 5 4

TOP VIEW

Data Sheet PN10285EJ02V0DS 2

DISCO

NTINUED

PS7142-1B,-2B,PS7142L-1B,-2B

<R> MARKING EXAMPLE

No. 1 pinMark

PS7142-1BNL601

Country AssembledType NumberAssembly Lot

6 01

Year Assembled(Last 1 Digit)

LN

Rank Code

In-house Code(L: Pb-Free)

Week Assembled

No. 1 pinMark

PS7142-2BNL601

Country AssembledType NumberAssembly Lot

6 01

Year Assembled(Last 1 Digit)

LN

Rank Code

In-house Code(L: Pb-Free)

Week Assembled

PS7142-1B PS7142-2B


DISCO

NTINUED

PS7142-1B,-2B,PS7142L-1B,-2B

<R> ORDERING INFORMATION Part Number Order Number Solder Plating

Specification Packing Style Safety Standard

Approval Application Part

Number*1

PS7142-1B PS7142-1B-A Pb-Free Magazine case 50 pcs Standard products PS7142-1B

PS7142L-1B PS7142L-1B-A (UL, BSI, CSA

PS7142L-1B-E3 PS7142L-1B-E3-A Embossed Tape 1 000 pcs/reel approved)

PS7142L-1B-E4 PS7142L-1B-E4-A

PS7142-2B PS7142-2B-A Magazine case 50 pcs PS7142-2B

PS7142L-2B PS7142L-2B-A

PS7142L-2B-E3 PS7142L-2B-E3-A Embossed Tape 1 000 pcs/reel

PS7142L-2B-E4 PS7142L-2B-E4-A

*1 For the application of the Safety Standard, following part number should be used.


DISCO

NTINUED

PS7142-1B,-2B,PS7142L-1B,-2B

ABSOLUTE MAXIMUM RATINGS (TA = 25°C, unless otherwise specified)

Ratings

Parameter Symbol PS7142-1B,PS7142L-1B

PS7142-2B,PS7142L-2B

Unit

Diode Forward Current (DC) IF 50 mA/ch

Reverse Voltage VR 5.0 V

Power Dissipation PD 50 mW/ch

Peak Forward Current *1 IFP 1 A/ch

MOS FET Break Down Voltage VL 400 V

Continuous Connection A IL 200 mA/ch

Load Current *2 Connection B 250 −

Connection C 400 −

Pulse Load Current *3 (AC/DC Connection)

ILP 400 mA/ch

Power Dissipation PD 560 375 mW/ch

Isolation Voltage *4 BV 1 500 Vr.m.s.

Total Power Dissipation PT 610 850 mW

Operating Ambient Temperature TA −40 to +85 °C

Storage Temperature Tstg −40 to +100 °C

*1 PW = 100 µs, Duty Cycle = 1% *2 Conditions: IF ≥ 2 mA. The following types of load connections are available.

Connection A VL (AC/DC)1 6

2 5

43 IL L

Connection B

Connection C

1 6

2 5

43

ILL

VL (DC)+–

1 6

2 5

43

IL

IL

LVL (DC)

+–

1 62 5

43 IL L VL (DC)+–

IL + IL

*3 PW = 100 ms, 1 shot *4 AC voltage for 1 minute at TA = 25°C, RH = 60% between input and output Pins 1-3 shorted together, 4-6 shorted together. (PS7142-1B) Pins 1-4 shorted together, 5-8 shorted together. (PS7142-2B)


DISCO

NTINUED

PS7142-1B,-2B,PS7142L-1B,-2B

RECOMMENDED OPERATING CONDITIONS (TA = 25°C)

Parameter Symbol MIN. TYP. MAX. Unit

LED Operating Current IF 2 10 20 mA

LED Off Voltage VF 0 0.5 V

ELECTRICAL CHARACTERISTICS (TA = 25°C)

Parameter Symbol Conditions MIN. TYP. MAX. Unit

Diode Forward Voltage VF IF = 10 mA 1.2 1.4 V

Reverse Current IR VR = 5 V 5.0 µA

MOS FET Off-state Leakage Current ILoff IF = 10 mA, VD = 400 V 0.03 1.0 µA

Output PS7142-1B Cout VD = 0 V, f = 1 MHz, IF = 10 mA 360 pF/ch

Capacitance

PS7142-2B 430

Coupled LED Off-state Current IFoff IL = 200 mA 2.0 mA

On-state Resistance Ron1 IF = 0 mA, IL = 10 mA 7 12 Ω

Ron2 IF = 0 mA, IL = 200 mA, t ≤ 10 ms 7 10

Turn-on Time *1, 2 ton IF = 10 mA, VO = 5 V, RL = 500 Ω, 0.03 0.2 ms

Turn-off PS7142-1B toff PW ≥ 10 ms 1.1 5.0 ms

Time *1, 2 PS7142-2B 1.1 2.0

Isolation Resistance RI-O VI-O = 1.0 kVDC 109 Ω

Isolation Capacitance CI-O V = 0 V, f = 1 MHz 1.1 pF/ch

*1 Test Circuit for Switching Time

VL

RL

IF

Rin

Pulse Input

Input monitor monitorVO

tontoff

10 %

90 %

0

VO = 5 V

50 %Input

Output

<R> *2 The turn-on time and turn-off time are specified as input-pulse width ≥ 10 ms. Be aware that when the device operates with an input-pulse width less than 10 ms, the turn-on time and turn-off time will increase.


DISCO

NTINUED

PS7142-1B,-2B,PS7142L-1B,-2B

TYPICAL CHARACTERISTICS (TA = 25°C, unless otherwise specified)

OUTPUT CAPACITANCE vs.O

utpu

t Cap

acita

nce

Cou

t (pF

)

Applied Voltage VD (V)

LOAD CURRENT vs. LOAD VOLTAGE

Load

Cur

rent

IL

(mA

)

Load Voltage VL (V)

Off-

stat

e Le

akag

e C

urre

nt I

Loff

(A)

Applied Voltage VD (V)

OFF-STATE LEAKAGE CURRENT vs.APPLIED VOLTAGE

APPLIED VOLTAGE

For

war

d V

olta

ge V

F (

V)

Ambient Temperature TA (˚C)

AMBIENT TEMPERATUREFORWARD VOLTAGE vs.

Max

imum

For

war

d C

urre

nt I

F (

mA

)


MAXIMUM FORWARD CURRENT vs.AMBIENT TEMPERATURE

Max

imum

Loa

d C

urre

nt I

L (m

A)


MAXIMUM LOAD CURRENT vs.AMBIENT TEMPERATURE

–25 0 25 50 7585 100

100

80

60

40

0

20

–25 0 25 50 75 100

1.6

1.4

1.2

1.0

0.8

IF = 50 mA

1 mA

5 mA10 mA20 mA30 mA

f = 1 MHz

20 40 60 80 100 120

500

0

375

250

125

10085750–25 5025

200

300

100

0

–4.0 –2.0 0 4.02.0

–100

–200

100

200IF = 0 mA

PS7142-2B

PS7142-1B

5001000 200 300 400

10–7

10–6

10–5

10–8

10–9

25 ˚C

TA = 85 ˚C

IF = 10 mA

Remark The graphs indicate nominal characteristics.


DISCO

NTINUED

PS7142-1B,-2B,PS7142L-1B,-2B

Normalized to 1.0 at TA = 25 ˚C,IF = 0 mA, IL = 10 mA

NORMALIZED ON-STATE RESISTANCE vs.

Nor

mal

ized

On-

stat

e R

esis

tanc

e R

on


n = 50 pcs,IF = 0 mA,IL = 10 mA

ON-STATE RESISTANCE DISTRIBUTION

Num

ber

(pc

s)

On-state Resistance Ron (Ω)

Num

ber

(pc

s)

Turn-on Time ton (ms)

TURN-ON TIME DISTRIBUTION

n = 50 pcs,IF = 10 mA,VO = 5 V

n = 50 pcs,IF = 10 mA,VO = 5 V

Num

ber

(pc

s)

Turn-off Time toff (ms)

TURN-OFF TIME DISTRIBUTION

AMBIENT TEMPERATURE

Tur

n-on

Tim

e to

n (m

s)

Forward Current IF (mA)

TURN-ON TIME vs. FORWARD CURRENTT

urn-

off T

ime

toff

(ms)

Forward Current IF (mA)

TURN-OFF TIME vs. FORWARD CURRENT

30252015105

2

6

8

12

4

10

0

VO = 5 V

30252015105

0.1

0.3

0.4

0.6

0.2

0.5

0

VO = 5 V

0.02 0.040

5

10

15

20

25

30

1.1 1.30

5

10

15

20

25

30

0.5

1.5

2.0

3.0

1.0

2.5

0.0100755025–25 0 6 8

0

5

10

15

20

25

30



DISCO

NTINUED

PS7142-1B,-2B,PS7142L-1B,-2B

Normalized to 1.0 at TA = 25 ˚C,IF = 10 mA, VO = 5 V

Nor

mal

ized

Tur

n-on

Tim

e to

n


NORMALIZED TURN-ON TIME vs.AMBIENT TEMPERATURE

Normalized to 1.0 at TA = 25 ˚C,IF = 10 mA, VO = 5 V

Nor

mal

ized

Tur

n-of

f Tim

e to

ff


NORMALIZED TURN-OFF TIME vs.AMBIENT TEMPERATURE

1000–25 25 50 75

2.5

3.0

0.0

2.0

1.5

1.0

0.5

1000–25 25 50 75

2.5

3.0

0.0

2.0

1.5

1.0

0.5



DISCO

NTINUED

PS7142-1B,-2B,PS7142L-1B,-2B

TAPING SPECIFICATIONS (in millimeters)

PS7142L-1B-E3PS7142L-2B-E3

PS7142L-1B-E4PS7142L-2B-E4

Tape Direction

Outline and Dimensions (Tape)

1.55±0.1

2.0±0.14.0±0.1 1.

75±

0.1

4.5 MAX.

10.4±0.1

12.0±0.1

1.5 +0.1–0

7.5±

0.1

10.3

±0.

1

16.0

±0.

3

4.0±0.1

0.3

Outline and Dimensions (Reel)

Packing: 1 000 pcs/reel

330±

2.0

100±

1.0

2.0±0.513.0±0.2

R 1.021.0±0.8

2.0±0.5

15.9 to 19.4Outer edge of flange

21.5±1.0

17.5±1.0


DISCO

NTINUED

PS7142-1B,-2B,PS7142L-1B,-2B

RECOMMENDED SOLDERING CONDITIONS (1) Infrared reflow soldering • Peak reflow temperature 260°C or below (package surface temperature) • Time of peak reflow temperature 10 seconds or less • Time of temperature higher than 220°C 60 seconds or less • Time to preheat temperature from 120 to 180°C 120±30 s • Number of reflows Three • Flux Rosin flux containing small amount of chlorine (The flux with a

maximum chlorine content of 0.2 Wt% is recommended.)

220˚C

Pac

kage

Sur

face

Tem

pera

ture

T (

˚C)

Time (s)

(heating)to 10 s

to 60 s

260˚C MAX.

Recommended Temperature Profile of Infrared Reflow

120±30 s(preheating)

180˚C

120˚C

(2) Wave soldering • Temperature 260°C or below (molten solder temperature) • Time 10 seconds or less • Preheating conditions 120°C or below (package surface temperature) • Number of times One • Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine

content of 0.2 Wt% is recommended.)

<R> (3) Soldering by soldering iron • Peak temperature (lead part temperature) 350°C or below • Time (each pins) 3 seconds or less • Flux Rosin flux containing small amount of chlorine (The flux with a

maximum chlorine content of 0.2 Wt% is recommended.) (a) Soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead. (b) Please be sure that the temperature of the package would not be heated over 100°C. (4) Cautions • Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent.


DISCO

NTINUED

PS7142-1B,-2B,PS7142L-1B,-2B

<R> USAGE CAUTIONS 1. Protect against static electricity when handling. 2. Avoid storage at a high temperature and high humidity.


DISCO

NTINUED

PS7142-1B,-2B,PS7142L-1B,-2B

The information in this document is current as of July, 2006. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC Electronics data sheets or data books, etc., for the most up-to-date specifications of NEC Electronics products. Not all products and/or types are available in every country. Please check with an NEC Electronics sales representative for availability and additional information.No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may appear in this document.NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC Electronics products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others.Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of a customer's equipment shall be done under the full responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information.While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in NEC Electronics products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment and anti-failure features.NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to NEC Electronics products developed based on a customer-designated "quality assurance program" for a specific application. The recommended applications of an NEC Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of each NEC Electronics product before using it in a particular application.

The quality grade of NEC Electronics products is "Standard" unless otherwise expressly specified in NEC Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products in applications not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to determine NEC Electronics' willingness to support a given application.

(Note)

•

•

•

•

•

•

M8E 02. 11-1

(1)

(2)

"NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its majority-owned subsidiaries."NEC Electronics products" means any product developed or manufactured by or for NEC Electronics (as defined above).

Computers, office equipment, communications equipment, test and measurement equipment, audioand visual equipment, home electronic appliances, machine tools, personal electronic equipmentand industrial robots.Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disastersystems, anti-crime systems, safety equipment and medical equipment (not specifically designedfor life support).Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, lifesupport systems and medical equipment for life support, etc.

"Standard":

"Special":

"Specific":


DISCO

NTINUED

PS7142-1B,-2B,PS7142L-1B,-2B

Caution GaAs Products This product uses gallium arsenide (GaAs). GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points.

• Follow related laws and ordinances when disposing of the product. If there are no applicable laws and/or ordinances, dispose of the product as recommended below.

1. Commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials.

2. Exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal.

• Do not burn, destroy, cut, crush, or chemically dissolve the product.

• Do not lick the product or in any way allow it to enter the mouth.

0604

NEC Compound Semiconductor Devices Hong Kong Limited E-mail: [email protected] Hong Kong Head Office TEL: +852-3107-7303 FAX: +852-3107-7309 Taipei Branch Office TEL: +886-2-8712-0478 FAX: +886-2-2545-3859 Korea Branch Office TEL: +82-2-558-2120 FAX: +82-2-558-5209

NEC Electronics (Europe) GmbH http://www.eu.necel.com/ TEL: +49-211-6503-0 FAX: +49-211-6503-1327

California Eastern Laboratories, Inc. http://www.cel.com/ TEL: +1-408-988-3500 FAX: +1-408-988-0279

Compound Semiconductor Devices DivisionNEC Electronics Corporation URL: http://www.ncsd.necel.com/

For further information, please contact

DISCO

NTINUED

Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailedwith the requirements of European Union (EU) Directive 2002/95/EC RestrictioSubstances in electrical and electronic equipment (RoHS) and the requiremen2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. Ththat the device is Pb-free. The –AZ suffix is used to designate devices containiexempted from the requirement of RoHS directive (*). In all cases the devices All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL’s understanding of the EU Directives and knowledgo into its products as of the date of disclosure of this information.

Restricted Substance per RoHS

Concentration Limit per RoHS (values are not yet fixed)

Concein

-A Lead (Pb) < 1000 PPM Not Detect

Mercury < 1000 PPM N

Cadmium < 100 PPM N

Hexavalent Chromium < 1000 PPM N

PBB < 1000 PPM N

PBDE < 1000 PPM N

If you should have any additional questions regarding our devices and compliastandards, please do not hesitate to contact your local representative. Important Information and Disclaimer: Information provided by CEL on its website or in other communicationcontent of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowprovided by third parties and makes no representation or warranty as to the accuracy of such information. Eintegrate information from third parties. CEL has taken and continues to take reasonable steps to provide reinformation but may not have conducted destructive testing or chemical analysis on incoming materials and suppliers consider certain information to be proprietary, and thus CAS numbers and other limited informationrelease. In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL pacustomer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability. DIS

CONTI

NU

4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279

below are compliant n on Use of Hazardous ts of EU Directive

e suffix –A indicates ng Pb which are have Pb-free terminals.

ge of the materials that

ntration contained CEL devices

-AZ ed (*)

ot Detected

ot Detected

ot Detected

ot Detected

ot Detected

nce to environmental

s concerting the substance ledge and belief on information fforts are underway to better presentative and accurate chemicals. CEL and CEL may not be available for

rt(s) at issue sold by CEL to

ED

ocmos fet ps7142-1b,-2b,ps7142l-1b,-2b › pdf › datasheets › ps71421b.pdf · the ps7142-1b,...

Documents