nxe-iqm87o hwdoc v10 - nexitenexite.co.kr/.../uploads/2016/10/nxe-iqm87o_hwdoc_v10.pdf ·...

Hardware Document NXTRDH-000900 R&D

Nexite, Inc. 1/27 Revision 1.0

NXE-IQM87O Hardware Document

January 08, 2014

Revision 1.0



Document Revision History

Doc. No. Rev. Description Date

NXTRDC

-

000900

1.0 Initial Release 01/08/2014

User’s Notice No part of this product, including the schematics and BIOS may be reproduced, transmitted,

transcribed, stored in a retrieval system, or translated into any language in any form by any means

without the express written permission of NEXITE Inc. except the document kept by the purchaser for

backup purposes.

© Copyright 2013 NEXITE Inc. All rights reserved



Contents

1. Introduction 4

1.1. General Description

1.2. Functional Block Diagram

2. System Overview 7

2.1. Main Board

2.2. Upgradeability

3. Switch & Connectors Descriptions 10

3.1. Board Switch Setting

3.2. Connectors Description

4. Board Implementation Guidelines 17

4.1. Mechanical Specification

4.2. Electrical Specification

4.3. PCI Express Interface Guide

4.4. SATA Interface Guide

4.5. USB Interface Guide

4.6. Ethernet Guide

4.7. Digital Display Interface Guide

4.8. Carrier board LPC/SPI Device

4.9. Protecting Logic Level signals Reclaimed from the VCC_12V Pool

4.10. COM Module Type Signal Guide



1. Introduction

This Document provides information about the components, features and connectors on the

NXE-IQM87O COM-Express Type6 Module board.

1.1. General Description

1.1.1. Main Board

- PCB size: 125mm x 95mm x 1.6T (14 Layers)

- COM-Express Type 6 Module

1.1.2. Processor

- Mobile 4th Generation Intel Core Processor Family (Haswell-H Processor Line)

- Support BGA1364 Package

: On-package Cache Memory integrated

: Intel Hyper-Threading Technology (Intel HT)

: Intel 64 Architecture

: Intel Turbo Boost Technology 2.0

1.1.3. System Memory

- Two channels of Unbuffered SO-DIMM

- Single-channel and Dual-channel memory organization modes

- 64-bit wide channels

- Non-ECC, Unbuffered DDR3L/DDR3L-RS Memory

- 1Gb, 2Gb, and 4Gb DDR3 DRAM device technologies are supported

- On-Die Termination (ODT)

- Asynchronous ODT

1.1.4. PCH

- Intel® 8 series QM87 (Lynx Point)

- PCI-Express Rev 2.0, up to 5.0GT/s

- Integrated SATA Host controller, up to 6.0Gb/s (Gen3)

- Integrated USB Host controller, up to 5.0Gb/s (Gen3)

- Integrated Gigabit LAN Controller, 10/100/1000Mbps

1.1.5. Graphics Subsystem

- Intel® HD Graphics Controller integrated within Processor package

: Encode/transcode HD content

: Playback of high definition content

: DirectX Video Acceleration (Full AVC/VC1/MPEG2 HW Decode)



: Playback of Blu-ray disc S3D content using HDMI 1.4a

: 3-independent and simultaneous display combination of DP/HDMI/DVI/LVDS/VGA

- 3-Digital Display interfaces

: Can be configured as DP, HDMI or DVI

: Link data rates of RBR(1.62GT/s), HBR(2.7GT/s) and HBR2(5.4GT/s)

: HDMI I/F supports 3D, 4K, Deep Color and x.v.Color

: DP I/F supports VESA Display port Standard Version 1, Revision 2, 3840x2160@60Hz

- Dual channel LVDS interface

: Support both OpenLDI and SPWG data format

: Support up to 1920x1200@60Hz

- Analog VGA interface

: Support up to 1920x1200@60Hz

1.1.6. Ethernet Subsystem

- Intel i217 Ethernet PHY

: 10/100/1000 BASE-T/TX IEEE802.3 conformance

: Automatic MDI/MDIX crossover at all speeds

: Intel vPro support

: 802.1Q & 802.1p, Two Queues(Tx & Rx)

1.1.7. Embedded Controller Subsystem

- ITE IT8518VG

: compatible with the LPC spec. v1.1

: 2-Standard serial ports (COM1, COM2)

: Support I2C I/F for Smart battery information

: Watchdog output

1.1.8. COM-Express I/F

- Support Type-6 Configuration

: Display I/F - 1x LVDS, 1x VGA, 3x Digital Display I/F

: PCIe I/F - 1x PEG x16(1x16,2x8,1x8/2x4), 8x PCIe x1(8x1,1x4/4x1)

: USB I/F - 8x USB2, 4x USB3

: SATA I/F - 3x SATA3, 1x SATA2

: LPC I/F, HDA I/F, SMBus, I2C, SPI I/F, WDT out, 2x Serial port(COM1,COM2)

: FAN Control, Sleep/LID Switch



1.2. Functional Block Diagram



2. System Overview

2.1. Main Board

2.1.1. Top Side

Note:

1 CPU Mobile 4th Generation Intel Core Processor Family (Haswell)

2 PCH Mobile Intel® 8 series QM87

3 Embedded Controller ITE IT8518VG

4 Ethernet PHY Intel Ethernet PHY i217

1 2

3

4



2.1.2. Bottom side

Note:

1 LVDS Transmitter CHRONTEL CH7511B

2 VRM12.6 Controller INTERSIL ISL95812HRZ

3 SPI EEPROM For BIOS/EC

4 Memory VRM Controller INTERSIL ISL88550A

1

2

3

4



2.2. Upgradeability

2.2.1. Processor

- User can not upgrade CPU because CPU type of NXE-IQM87O is FCBGA type.

- Mobile 4th Generation Intel Core Processor Family (Haswell-H Processor Line)

2.2.2. Memory

- SO-DIMM DDR3L / DDR3L-RS

- Data Rate : 1333 / 1600 MT/s

- Maximum capacity: Up to 16GB (8GB x2ea)

2.2.3. Display

- DDI I/F Can be configured as Display Port(DP), HDMI or DVI

- 3-independent and simultaneous display combination of DP/HDMI/DVI/LVDS/VGA

- Valid 3-Display Configurations

Display1 Display2 Display3 Max. resolution

display1

Max. resolution

display2

Max. resolution

display3

HDMI HDMI DP 4906x2304@24Hz 2560x1600@60Hz

3840x2160@60Hz

DVI DVI DP 1920x1200@60Hz 3840x2160@60Hz

DP DP DP 3840x2160@60Hz

VGA DP HDMI 1920x1200@60Hz 3840x2160@60Hz 4906x2304@24Hz 2560x1600@60Hz

LVDS DP HDMI 1920x1200@60Hz 3840x2160@60Hz 4906x2304@24Hz 2560x1600@60Hz

LVDS DP DP 1920x1200@60Hz 3840x2160@60Hz

LVDS HDMI HDMI 1920x1200@60Hz 4906x2304@24Hz 2560x1600@60Hz

* 1. DP in the above table is supported for 4-lanes with link data rate HBR2.

* 2. Requires support of 2 channel memory 1600MT/s configuration for driving 3 DP 3840x2160@60Hz resolutions.

- DisplayPort Resolutions for 1,2,4 Lanes - Link Data Rate

Link Data Rate Lane Count

1 2 4

RBR 1064x600 1400x1050 2240x1400

HBR 1280x960 1920x1200 2880x1800

HBR2 1920x1200 2880x1800 3840x2160



3. Switch & Connectors Description

3.1. Board Switch Setting

3.1.1. BIOS Destination Switch Description (SW1, 1.27mm Half-Pitch)

3.1.2. LVDS Enable Switch Description (SW1, 1.27mm Half-Pitch)

Channel Function AT Mode ATX Mode Remarks 1 ATX / AT Mode

Default

‘ATX Mode’

Channel Function LVDS ENABLE LVDS DISABLE Remarks 2 LVDS Enable

Default ‘Disable’

1 2

1 2 1 2

1 2

LVDS Resolution

1.ATX/AT Mode 2.LVDS Enable



3.1.3. LVDS Resolution SEL Switch Description (SW2,SW3, 1.27mm Half-Pitch)

No. Resolution SW2 SW3 Remarks 1 1920 x 1080, 24bit

SPWG Default ‘Full-HD’

Dual channel

2 1920 x 1080, 24bit Open-LDI

Dual channel

3 1366 x 768, 24bit SPWG

Single channel

4 1366 x 768, 24bit Open-LDI

Single channel

5 1280 x 1024, 18bit SPWG

Dual channel

6 1280 x 1024, 18bit Open-LDI

Dual channel

7 1024 x 768, 18bit SPWG

Single channel

8 1024 x 768, 18bit Open-LDI

Single channel

9 1280 x 1024, 24bit SPWG

Dual channel

10 Customize slot (0-6) - - Reserved

1 2

1 2

1 2 1 2

1 2

1 2

1 2

1 2

1 2 1 2

1 2 1 2

1 2 1 2

1 2 1 2

1 2 1 2



3.2 Connectors Description

3.2.1. M/B Internal Connector

2

1



1) COM-Express Type 6 Interface (CN3,CN4, QT012206-1031-2H, Foxconn)

No A B C D

1 GND GND GND GND

2 GBE0_MDI3- GBE0_ACT# GND GND

3 GBE0_MDI3+ LPC_FRAME# USB0_SSRX- USB0_SSTX-

4 GBE0_LINK100# LPC_AD0 USB0_SSRX+ USB0_SSTX+

5 GBE0_LINK1000# LPC_AD1 GND GND

6 GBE0_MDI2- LPC_AD2 USB1_SSRX- USB1_SSTX-

7 GBE0_MDI2+ LPC_AD3 USB1_SSRX+ USB1_SSTX+

8 GBE0_LINK# LPC_DRQ0# GND GND

9 GBE0_MDI1- LPC_DRQ1# USB2_SSRX- USB2_SSTX-

10 GBE0_MDI1+ LPC_PCLK USB2_SSRX+ USB2_SSTX+

11 GND GND GND GND

12 GBE0_MDI0- PWRBTN# USB3_SSRX- USB3_SSTX-

13 GBE0_MDI0+ SMB_CLK USB3_SSRX+ USB3_SSTX+

14 NC SMB_DAT GND GND

15 SUS_S3# SMB_ALERT# NC DDI1_CTRLCLK_AUX+

16 SATA0_TX+ SATA1_TX+ NC DDI1_CTRLDATA_AUX-

17 SATA0_TX- SATA1_TX- NC NC

18 SUS_S4# SUS_STAT# NC NC

19 SATA0_RX+ SATA1_RX+ PCIE_RX6+ PCIE_TX6+

20 SATA0_RX- SATA1_RX- PCIE_RX6- PCIE_TX6-

21 GND GND GND GND

22 SATA2_TX+ SATA3_TX+ PCIE_RX7+ PCIE_TX7+



No A B C D

23 SATA2_TX- SATA3_TX- PCIE_RX7- PCIE_TX7-

24 SUS_S5# PWROK DDI1_HPD NC

25 SATA2_RX+ SATA3_RX+ NC NC

26 SATA2_RX SATA3_RX NC DDI1_LANE0+

27 BATLOW# WDT NC DDI1_LANE0-

28 ATA_ACT# HDA_SDIN2 NC NC

29 HDA_SYNC HDA_SDIN1 NC DDI1_LANE1+

30 HDA_RST# HDA_SDIN0 NC DDI1_LANE1-

31 GND GND GND GND

32 HDA_BITCLK SPKR DDI2_CTRLCLK_AUX+ DDI1_LANE2+

33 HDA_SDOUT I2C_CLK DDI2_CTRLDATA_AUX- DDI1_LANE2-

34 BIOS_DIS0# I2C_DAT DDI2_AUX_SEL DDI1_AUX_SEL

35 THRMTRIP# THRM# NC NC

36 USB6- USB7- DDI3_CTRLCLK_AUX+ DDI1_LANE3+

37 USB6+ USB7+ DDI3_CTRLDATA_AUX- DDI1_LANE3-

38 USB_6_7_OC# USB_4_5_OC# DDI3_AUX_SEL NC

39 USB4- USB5- DDI3_LANE0+ DDI2_LANE0+

40 USB4+ USB5+ DDI3_LANE0- DDI2_LANE0-

41 GND GND GND GND

42 USB2- USB3- DDI3_LANE1+ DDI2_LANE1+

43 USB2+ USB3+ DDI3_LANE1- DDI2_LANE1-

44 USB_2_3_OC# USB_0_1_OC# DDI3_HPD DDI2_HPD

45 USB0- USB1- NC NC

46 USB0+ USB1+ DDI3_LANE2+ DDI2_LANE2+

47 VCC_RTC EXCD1_PERST# DDI3_LANE2- DDI2_LANE2-

48 EXCD0_PERST# EXCD1_CPPE# NC NC

49 EXCD0_CPPE# SYS_RST# DDI3_LANE3+ DDI2_LANE3+

50 LPC_SERIRQ CB_RESET# DDI3_LANE3- DDI2_LANE3-

51 GND GND GND GND

52 PCIE_TX5+ PCIE_RX5+ PEG_RX0+ PEG_TX0+

53 PCIE_TX5- PCIE_RX5- PEG_RX0- PEG_TX0-

54 GPI0 GPO1 TYPE0# PEG_LANE_RV#




No A B C D


57 GND GPO2 TYPE1# TYPE2#



60 GND GND GND GND



63 GPI1 GPO3 NC NC

64 PCIE_TX1+ PCIE_RX1+ NC NC

65 PCIE_TX1- PCIE_RX1- PEG_RX4+ PEG_TX4+

66 GND WAKE0# PEG_RX4- PEG_TX4-

67 GPI2 WAKE1# NC GND



70 GND GND GND GND

71 LVDS_A0+ LVDS_B0+ PEG_RX6+ PEG_TX6+

72 LVDS_A0- LVDS_B0- PEG_RX6- PEG_TX6-

73 LVDS_A1+ LVDS_B1+ GND GND

74 LVDS_A1- LVDS_B1- PEG_RX7+ PEG_TX7+

75 LVDS_A2+ LVDS_B2+ PEG_RX7- PEG_TX7-

76 LVDS_A2- LVDS_B2- GND GND

77 LVDS_VDDEN LVDS_B3+ NC NC

78 LVDS_A3+ LVDS_B3- PEG_RX8+ PEG_TX8+

79 LVDS_A3- LVDS_BKLT_EN PEG_RX8- PEG_TX8-

80 GND GND GND GND

81 LVDS_CLKA+ LVDS_CLKB+ PEG_RX9+ PEG_TX9+

82 LVDS_CLKA- LVDS_CLKB PEG_RX9- PEG_TX9-

83 LVDS_I2CCK(NC) LVDS_BKLT_CTRL NC NC

84 LVDS_I2CDAT(NC) VCC_5V_STBY GND GND

85 GPI3 VCC_5V_STBY PEG_RX10+ PEG_TX10+

86 NC VCC_5V_STBY PEG_RX10- PEG_TX10-

87 NC VCC_5V_STBY GND GND

88 PCIE0_CK_REF+ BIOS_DIS1# PEG_RX11+ PEG_TX11+



No A B C D

89 PCIE0_CK_REF- VGA_RED PEG_RX11- PEG_TX11-

90 GND GND GND GND

91 SPI_POWER VGA_GRN PEG_RX12+ PEG_TX12+

92 SPI_MISO VGA_BLU PEG_RX12- PEG_TX12-

93 GPO0 VGA_HSYNC GND GND

94 SPI_CLK VGA_VSYNC PEG_RX13+ PEG_TX13+

95 SPI_MOSI VGA_DDC_CLK PEG_RX13- PEG_TX13-

96 TPM_PP VGA_DDC_DAT GND GND

97 TYPE10# SPI_CS# NC NC

98 SER0_TX NC PEG_RX14+ PEG_TX14+

99 SER0_RX NC PEG_RX14- PEG_TX14-

100 GND GND GND GND

101 SER1_TX FAN_PWNOUT PEG_RX15+ PEG_TX15+

102 SER1_RX FAN_TACHIN PEG_RX15- PEG_TX15-

103 LID# SLEEP# GND GND

104 VCC_12V VCC_12V VCC_12V VCC_12V






110 GND GND GND GND

2) LPC I/F Connector for Debugging (CN5, 12505WR-10A00, Yeonho)

1 +3.3V

2 LPC_AD0

3 LPC_AD1

4 LPC_AD2

5 LPC_AD3

6 RESET#

7 LPC_FRAME#

8 GND

9 LPC_CLK

10 NC



4. Board Implementation Guidelines

4.1. Mechanical Specification

4.1.1. Type-6 Basic Module Size

- 125mm x 95mm x 1.6T(2.0T), Tolerance 0.25mm

- Mounting holes: 5ea for use with 2.5mm screw (M2.5 screw)

- Mounting holes spec.: 6mm diameter pads, 2.7mm plated holes

- The 440pin connector pair is mounted on the backside of Module PCB

<Basic Module Layout>

4.1.2. Module Connector

- Connector configuration: Total 440pin, 2-pieces of a 220pin, 0.5mm pitch receptacle

- Used receptacle : QT012206-1031-2H, Foxconn

<Module receptacle>



4.1.3. Carrier Board Connector

- Connector configuration: Total 440pin, 2-pieces of a 220pin, 0.5mm pitch plug

- Usable connector

Individual

5mm Stack

Foxconn QT002206-2131-3H

Tyco Electronics 3-1827253-6

Combined

5mm Stack



Individual

8mm Stack



Combined

8mm Stack



<Carrier Board Plug>

4.1.4. Module Heat-Spreader (or Heat-sink)

- Provides a common interface between Module & specific thermal solution

<Overall height for Module assembly with Heat-spreader>



4.2. Electrical Specification

4.2.1. Input Power

Power Rail Module

Pin

Current

Capability

(Amps)

Nominal

Input

(Volts)

Input

Range

(Volts)

De-rated

Input

(Volts)

Max. Input

Ripple

(mV)

Max. Module

Input Power

(w/de-rated

Input)

(Watts)

VCC_12V 12 12 11.4 ~ 12.6 11.4 +/- 100 137

VCC_5V_SBY 2 5 4.75 ~ 5.25 4.75 +/- 50 9

VCC_RTC 0.5 3 2.0 ~ 3.3 +/- 20

4.2.2. Input Power Sequencing

T1 VCC_RTC rise to VCC_5V_SBY rise ≥ 0ms

T2 VCC_5V_SBYrise to VCC_12V rise ≥ 0ms

T3 VCC_12V rise to PWR_OK rise ≥ 0ms

T4 PWR_OK fall to VCC_12V fall ≥ 0ms

T5 VCC_12V fall to VCC_5V_SBY fall ≥ 0ms

T6 VCC_5V_SBY fall to VCC_RTC fall ≥ 0ms

4.2.3. Input Power Rise Time

T1 VCC_12V, VCC_5V_SBY, 10% ~ 95% rise 0.1ms ≤ T1 ≤ 20ms



4.2.4. Signal Integrity Requirements

Signal Group General Description Spec. Reference

Analog VGA 75Ω Single ended, Ground-referenced

DDI 85Ω Differential pair, Ground-referenced Intel PDG

Gigabit Ethernet 100Ω Differential pair, Ground-referenced IEEE802.3

LVDS 100Ω Differential pair, Ground-referenced Chrontel PDG

LPC Clock 50Ω Single ended, Ground-referenced Intel PDG

PEG 80Ω Differential pair, Ground-referenced Intel PDG

PCI Express 85Ω Differential pair, Ground-referenced Intel PDG

PCI Express Clock 90Ω Differential pair, Ground-referenced Intel PDG

Serial ATA 85Ω Differential pair, Ground-referenced Intel PDG

USB 85Ω Differential pair, Ground-referenced Intel PDG

4.3. PCI Express Interface Guide

4.3.1. PCI Express Link Configuration

COM Express Pin Name Preferred Link Configuration

PCIE7 X 1 X 1

PCIE6 X 1 X 1

PCIE5 X 1 X 1

PCIE4 X 1 X 1

PCIE3 X 1 X 4

PCIE2 X 1

PCIE1 X 1

PCIE0 X 1

- PCIE x4 port configuration can be supported by BIOS



4.3.2. PEG Link Configuration

COM Express Pin Name Preferred Link Configuration

PEG15 X 16

X 8 X 4

PEG14

PEG13

PEG12

PEG11 X 4

PEG10

PEG9

PEG8

PEG7 X 8 X 8

PEG6

PEG5

PEG4

PEG3

PEG2

PEG1

PEG0

- PEG port can be used to for PCI Express Graphics or for General purpose I/O device

4.3.3. PCI Express Guide for Slot

Classification Max. Length LC [mm/inches]

Note

Gen1 228/9.0 Allowance for 4.4db [email protected]/GHz/inch & 1.25dB crosstalk

Gen2 113/4.45

Gen3

Diff Pair Matching 0.127/0.005 5mil



4.3.4. PCI Express Guide for Device down

Classification Max. Length LC [mm/inches]

Note

Gen1 402/15.85 Allowance for 8.3dB [email protected]/GHz/inch & 2.75dB crosstalk

Gen2 203/8.0

Gen3


Gen3 AC-Cap 220nF 180nF ~ 265nF,

Gen2 AC-Cap 110nF 75nF ~ 265nF

4.4. SATA Interface Guide

4.4.1. SATA Length Guide

Classification Max. Length LC [inches]

Note

Gen1 7.2 Allowance @0.28dB/GHz/inch

Gen2 3.0 Allowance @0.28dB/GHz/inch

Gen3




4.5. USB Interface Guide

4.5.1. USB2.0 Length Guide


Note

USB2.0 14 Allowance @0.28dB/GHz/inch


4.5.2. USB3.0 Length Guide


Note

USB3.0 5




4.6. Ethernet Guide

4.6.1. Ethernet Length Guide


Note

Gigabit Ethernet 5 0.28dB/GHz/Inch


Pair-Pair Matching 2

4.7. Digital Display Interface Guide

4.7.1. Digital Display Interface Guide


Note

DDI 5


Pair-Pair Matching 1

AC-Cap 100nF 75nF ~ 200nF

- HDMI or DVI Port is required level shifters on the Carrier board.



4.8. Carrier board LPC / SPI Device

4.8.1. Carrier board LPC Device Guide

- L2= 1" Max

- Lc = L1 + L2 = 8.88" Max

- Carrier board LPC Devices should be reset with Module Conn's CB_RESET#.

4.8.2. Carrier board SPI Device Guide

Classification Max. Length

[inches] Note

SPI Bus 4.5

Group Matching 0.1

SPI Power - From a pin on the COM-Ex Module

- BIOS disable signals Table

BIOS_DIS1# BIOS_DIS0# SPI CS1# SPI_CS0# BIOS Entry Note

1*1 1 Carrier Module Module Default

1 0 - - - Not Support

0 1 Module Carrier Carrier

0 0 Carrier Module Module

*1. '1' means module pin open, '0' means module pin pull-down to GND on the Carrier board. (1~10Kohm)



4.9. Protecting Logic Level signals Reclaimed from the VCC_12V Pool

4.9.1. Signals that need to be protected

- Some Logic level signals below on the table need to protect from pins that are

VCC_12V supply pins on TYPE 1 - 5 module.

Signals Note

SER0_TX, SER1_TX TTL level output from Module

SER0_RX, SER1_RX TTL level input to Module

LID#, SLEEP# 3.3V logic level input to Module, Suspend domain

FAN_TACHIN 3.3V logic level input to Module

FAN_PWMOUT 3.3V logic level output from Module

4.9.2. Method for Logic protecting

<Carrier Output Logic>

<Carrier Input Logic>



4.10. COM Module Type Signal Guide

4.10.1. Signals for Module Type on module

Signals Note

TYPE 0# GND for Type 3 and 5 on module

NC for Type 2, 4 and 6 on module

TYPE 1# GND for Type 4 and 5 on module

NC for Type 2, 3 and 6 on module

TYPE 2# GND for Type 6 on module

NC for Type 2, 3, 4 and 5 on module

TYPE 10# 47K Pull down for Type 10 on module

NC for Type 1-6 on module

4.10.2. Module Type 6 Detection Logic on Carrier board

- END -

nxe-iqm87o hwdoc v10 - nexitenexite.co.kr/.../uploads/2016/10/nxe-iqm87o_hwdoc_v10.pdf ·...

Documents