nwm - nidec-shimpo corporation · 2016-03-16 · worm gear reducers nwm 110b 40 180tc foot mount b3...
TRANSCRIPT
NWM
NWS
Worm Gear Reducers
NWM 110B 40 180TC Foot Mount B3 Torque Arm
Model Size Ratio Input Size Output Design Mounting Accessories
Aluminum Housing 548C
Shaft Mounted
standard hollow output bore
B3Torque Arm30B 7.5
40B 1056C B6
50B 15
Baseplate63B 20140TC
Foot Mounted
optional single or double plug-
in output shaft
B775B 25
90B 30180TC B8 Double Extension
Worm Shaft-- 40
Cast Iron Housing 50210TC
Flange Mounted
optional FA mounting fl ange
and hollow output bore
V5110B 60
Protective Cover130B 80-- V6
-- 100
1 Aluminum alloy housing with patented heat sink design provides greater surface area and higher thermal capacity than traditional cast-iron housings.
2 Two bearings along the input shaft prevent leaks and contribute to fl exibility in mounting. High quality bearings increase reducer life versus worm reducers with a bushing on the input.
3 NEMA and IEC motor inputs available for greater customer fl exibility.
4 Double-lip oil seals aid the reducer’s thermal capacity and extended the reducer’s oil life.
5 Use of O-rings on the input fl ange and output cover pre-vents leaks more eff ectively than a paper gasket.
6 Hardened worm shaft gives increased durability versus forged worm shafts.
7 Standard hollow output bore and optional plug-in shafts provide greater fl exibility in ordering and reduced inventory.
8 Polyester epoxy paint applied on the inside and outside of the gearcase protects against rust.
9 There is no breather for size 30B to 90B, there is breather for size 110B and 130B. NWM and NWS are universal mount-ing, sealed for life, mainte-nance-free reducers.
10 No compression chamber required, preventing leaks and the risk of oil oxidation and contamination, and contribut-ing to mounting fl exibility.
11 Automated manufacturing process from an ISO 9001 certifi ed company assures quality, reliable gearing.
12 Aluminum units are prefi lled with synthetic oil; cast iron units are prefi lled with min-eral oil.
1
2
3
4
56
4
7
2
8
Nomenclature
Features
NWMMotor Input Flange
NMSInput Shaft
2
Worm Gear Reducer Ratings 1750 rpm
SizeExact Ratio
i
Output Speed
rpm
Max Torquein-lbs
Max Input
HPOHL
75B
7.5 233 1555 6.47 581
10 175 1639 5.17 639
15 117 1681 3.62 732
20 88 1765 2.95 806
25 70 1681 2.31 868
30 58 1933 2.32 922
40 44 1849 1.76 1015
50 35 1765 1.40 1093
60 29 1681 1.18 1162
80 22 1597 0.91 1279
100 18 1513 0.75 1378
90B
7.5 233 2681 11.03 643
10 175 2866 8.94 708
15 117 3329 7.08 810
20 88 3287 5.37 891
25 70 3144 4.21 960
30 58 3631 4.26 1020
40 44 3329 3.04 1123
50 35 3144 2.39 1210
60 29 2959 1.96 1286
80 22 2396 1.30 1415
100 18 2270 1.05 1524
110B
7.5 233 4640 19.09 812
10 175 5027 15.69 894
15 117 5514 11.74 1023
20 88 5413 8.74 1126
25 70 5707 7.46 1213
30 58 6094 7.05 1289
40 44 5901 5.19 1419
50 35 5548 3.58 1529
60 29 5178 3.26 1625
80 22 4329 2.21 1788
100 18 4060 1.76 1926
130B
7.5 233 6304 25.65 1062
10 175 6893 21.51 1169
15 117 7733 16.46 1339
20 88 7649 12.21 1473
25 70 7817 10.22 1587
30 58 8742 9.99 1686
40 44 8826 7.76 1856
50 35 8238 6.02 2000
60 29 7565 4.80 2125
80 22 7061 3.55 2339
100 18 6220 2.66 2519
SizeExact Ratio
i
Output Speed
rpm
Max Torquein-lbs
Max Input
HPOHL
30B
5 350 160 1.02 125
7.5 233 160 0.70 143
10 175 160 0.53 157
15 117 160 0.38 180
20 88 151 0.28 198
25 70 185 0.30 213
30 58 177 0.25 226
40 44 160 0.18 249
50 35 151 0.15 268
60 29 134 0.12 285
80 22 109 0.08 314
40B
5 350 303 1.89 240
7.5 233 353 1.50 274
10 175 370 1.21 302
15 117 370 0.83 346
20 88 361 0.64 380
25 70 328 0.48 410
30 58 403 0.53 435
40 44 378 0.40 479
50 35 353 0.31 516
60 29 328 0.26 549
80 22 277 0.18 604
100 18 244 0.14 651
50B
5 350 572 3.57 329
7.5 233 647 2.72 377
10 175 664 2.12 414
15 117 681 1.52 474
20 88 656 1.14 522
25 70 597 0.86 562
30 58 740 0.94 598
40 44 689 0.70 658
50 35 647 0.56 709
60 29 605 0.47 753
80 22 546 0.35 829
100 18 462 0.26 893
63B
7.5 233 1076 4.48 492
10 175 1093 3.49 542
15 117 1177 2.59 620
20 88 1135 1.92 683
25 70 1093 1.54 735
30 58 1345 1.66 781
40 44 1219 1.19 860
50 35 1135 0.94 926
60 29 1093 0.80 984
80 22 1025 0.61 1083
100 18 992 0.53 1167
3
Worm Gear Reducers
Dimensions
Size 30B 40B 50B 63B 75B 90B 110B 130B
RH 0.71 0.84 1.11 1.24 1.37 1.52 1.80 1.92
SH 0.1875 0.1875 0.250 0.250 0.250 0.3125 0.375 0.375
UH
VB 0.83 1.02 1.18 1.42 1.57 1.77 1.97 2.36
0.625 + 0.0010 0.750 + 0.001
0 1.000 + 0.0010 1.125 + 0.001
0 1.250 + 0.0010 1.375 + 0.001
0 1.625 + 0.0010 1.750 + 0.001
0
Hollow Output Bore
Size 30B 40B 50B 63B 75B 90B 110B 130B
R 0.70 0.83 1.11 1.23 1.36 1.51 1.79 1.92
S 0.1875 0.1875 0.250 0.250 0.250 0.3125 0.375 0.375
U
U KEY 0.1875 x 1.250 0.1875 x 1.500 0.250 x 1.500 0.250 x 2.000 0.250 x 2.250 0.3125 x 2.50 0.375 x 2.750 0.375 x 2.750
UT 1/4 - 20 1/4 - 20 3/8 - 16 3/8 - 16 1/2 - 13 1/2 -13 5/8 - 11 5/8 - 11
V 1.57 1.97 1.97 2.36 2.76 3.15 3.54 3.54
VA 1.67 2.09 2.11 2.50 2.89 3.33 3.72 3.74
Y 5.82 7.25 7.84 9.41 10.50 12.17 13.54 14.17
0.6250
- 0.0005 0.7500
- 0.0005 1.0000
- 0.0005 1.1250
- 0.0005 1.2500
- 0.0005 1.3750
- 0.0005 1.6250
- 0.0005 1.7500
- 0.0005
Output Shaft
NWM
Shaft Mount Foot Mount Flange Mount
Hollow Output Bore
Output Shaft Output Flange
NWS
4
DimensionsSize 30B 40B 50B 63B 75B 90B 110B 130B
A 2.48 3.07 3.62 4.41 4.72 5.51 6.10 6.69
B 2.24 2.81 3.31 4.02 4.69 5.31 6.59 7.38
BA 2.56 2.95 3.35 3.74 4.53 5.12 6.50 8.46
BC 2.95 3.43 3.94 4.33 5.51 6.30 7.87 9.84
BH 0° 45° 45° 45° 45° 45° 45° 45°
BK
BL M6x11 (N = 4) M6x10 (N = 4) M8x14 (N = 4) M8x14 (N = 8) M8x14 (N = 8) M10x18 (N = 8) M10x18 (N = 8) M12x21 (N = 8)
C 1.18 1.57 1.97 2.48 2.95 3.54 4.33 5.12
D 1.57 1.97 2.36 2.83 3.39 4.06 5.02 5.81
E 2.13 2.76 3.15 3.94 4.72 5.51 6.69 7.87
F 1.73 2.36 2.76 3.35 3.54 3.94 4.53 4.72
G 0.22 0.26 0.28 0.31 0.39 0.43 0.59 0.59
H 0.26 0.28 0.33 0.33 0.43 0.51 0.55 0.63
J 3.15 3.94 4.72 5.67 6.77 8.11 9.92 11.50
K 1.26 1.69 1.93 2.64 2.83 2.91 - -
L 2.20 2.80 3.35 4.06 4.41 5.12 5.67 6.10
M 2.28 2.87 3.43 4.17 4.49 5.28 5.83 6.38
N 1.06 1.38 1.57 1.97 2.36 2.76 3.35 3.94
O 3.82 4.78 5.67 6.85 8.07 9.37 11.61 13.19
P 2.64 3.15 3.54 4.13 4.96 5.63 6.81 7.60
Q 1.97 2.40 2.91 3.54 4.13 4.92 5.59 6.38
T 1.73 2.17 2.52 3.15 3.66 4.02 4.92 5.51
Z 2.91 3.63 3.92 4.71 5.25 6.09 6.77 7.09
2.165 0- 0.0018 2.362 0
- 0.0018 2.756 0- 0.0018 3.150 0
- 0.0021 3.740 0- 0.0021 4.331 0
- 0.0021 5.118 0- 0.0021 7.087 0
- 0.0021
Output Flange (FA)Size 30B 40B 50B 63B 75B 90B 110B 130B
AA 2.68 3.15 3.35 5.91 6.50 6.89 9.06 10.04
AB 2.15 2.64 3.54 3.23 4.37 4.37 5.16 5.51
AC 3.15 4.33 4.92 7.09 7.87 8.27 11.02 12.60
AD 2.76 3.74 4.33 5.59 6.69 7.87 10.24 11.42
AF 0.24 0.28 0.35 0.39 0.51 0.51 0.59 0.59
AG 0.16 0.16 0.20 0.24 0.24 0.24 0.24 0.24
AH 45° 45° 45° 45° 45° 45° 45° 22.5°
AK
AL 0.26 0.35 0.43 0.43 0.55 0.55 0.55 0.63
1.969 0+ 0.0015 2.362 0
+ 0.0018 2.756 0+ 0.0018 4.528 0
+ 0.0021 5.118 0+ 0.0025 5.984 0
+ 0.0025 6.693 0+ 0.0025 7.087 0
+ 0.0025
Input ShaftSize 40B 50B 63B 75B 90B 110B 130B
SB 0.125 0.1875 0.1875 0.1875 0.1875 0.250 0.250
RB 0.55 0.70 0.83 0.96 0.96 1.24 1.36
UB
UB KEY 0.125 x 1.000 0.1875 x 1.250 0.1875 x 1.500 0.1875 x 2.000 0.1875 x 2.000 0.250 x 2.250 0.250 x 2.500
UR 1/4 - 20 1/4 - 20 1/4 - 20 1/4 - 20 1/4 - 20 3/8 - 16 1/2 - 13
VN 1.18 1.58 1.97 2.36 2.36 2.76 3.15
0.500 0- 0.0005 0.625 0
- 0.0005 0.750 0- 0.0005 0.875 0
- 0.0005 0.875 0- 0.0005 1.125 0
- 0.0005 1.250 0- 0.0005
5
Worm Gear Reducers
Accessories
Torque ArmSize I IA IL IR IW
30B 3.35 0.94 0.31 0.59 0.55
40B 3.94 1.24 0.39 0.71 0.55
50B 3.94 1.52 0.39 0.71 0.55
63B 5.91 1.93 0.39 0.71 0.55
75B 7.87 1.87 0.79 1.18 0.98
90B 7.87 2.26 0.79 1.18 0.98
110B 9.84 2.44 0.98 1.38 1.18
130B 9.84 2.72 0.98 1.38 1.18
Protective CoverSize Q
30B 1.65
40B 1.97
50B 2.28
63B 2.72
75B 2.91
90B 3.39
110B 3.70
130B 4.02
High Speed Extension ShaftSize EA U VN UR S2 R2 KEY
40B 2.09 1.18 1/4 - 20 0.125 0.55 0.125 x 1.000
50B 2.52 1.57 1/4 - 20 0.1875 0.70 0.1875 x 1.250
63B 2.95 1.97 1/4 - 20 0.1875 0.83 0.1875 x 1.500
75B 3.54 2.36 1/4 - 20 0.1875 0.96 0.1875 x 2.000
90B 4.25 2.36 1/4 - 20 0.1875 0.96 0.1875 x 2.000
110B 5.31 2.76 3/8 - 16 0.250 1.24 0.250 x 2.250
130B 6.10 3.15 1/2 - 13 0.250 1.36 0.250 x 2.500
0.500 0- 0.0005
0.625 0- 0.0005
0.750 0- 0.0005
0.875 0- 0.0005
0.875 0- 0.0005
1.125 0- 0.0005
1.250 0- 0.0005
BaseplatesSize 30B 40B-A 40B-B 50B 63B-A 63B-B 75B 90B
A 4.37 4.37 5.75 6.38 7.05 7.99 8.43 9.49
B 3.31 3.31 4.49 4.69 4.88 5.24 5.87 6.14
C 0.34 0.34 0.41 0.49 0.49 0.49 0.49 0.49
DA 2.24 2.64 2.76 2.99 3.50 3.66 4.00 4.63
DB 3.43 4.21 4.33 4.96 5.98 6.14 6.95 8.17
T 0.67 0.67 0.79 0.63 0.67 0.83 0.61 0.57
6
Mounting and Availability
Mounting Positions
NEMA Flange Availability
*PLEASE NOTE: Mounting the reducer in V5 or V6 position may require added bearing maintenance. Please contact a NIDEC-SHIMPO Technical Service Representative for assistance with these mounting positions.
V6*V5*B6
B7
B3
B8
SizeNEMAFlange
Input BoreDiameter
Available Ratios
5 7.5 10 15 20 25 30 40 50 60 80 100
30B 48C 0.500 • • • • • • • • • • •
40B 56C 0.625 • • • • • • • • • • • •
50B 56C 0.625 • • • • • • • • • • • •
63B56C 0.625 • • • • • • • • •
140TC 0.875 • • • • • • •
75B
56C 0.625 • • • • •
140TC 0.875 • • • • • • • •
180TC 1.125 • • •
90B
56C 0.625 • •
140TC 0.875 • • • • •
180TC 1.125 • • • • • • •
110B
140TC 0.875 • • • •
180TC 1.125 • • • • • •
210TC 1.375 • • • •
130B
140TC 0.875 • •
180TC 1.125 • • • • •
210TC 1.375 • • • • • • •
7
NIDEC MOTOR CANADA CORPORATION6617 Thimens Blvd
Saint-Laurent, Québec H4S 1W2, CanadaPhone: (514) 332-1880
www.drives.nidec-shimpo.com