nustar logistics, l.p....nustar logistics, l.p. product specifications central west i september15,...

NuStar Logistics, L.P.

Product Specifications

Central West

i September15, 2014

Central West

Product Specifications ii September 15, 2014

Table of Contents

Page

Central West Products Shipped by Pipeline v

ARIZONA GASOLINE

84 OCTANE CONVENTIONAL GASOLINE- TUSCON 1,2

ARIZONA CLEANER BURNING GASOLINE (CBG) GRADE 30 X2 3,4

ARIZONA CLEANER BURNING GASOLINE (CBG) GRADE 30 X3 5 ARIZONA CLEANER BURNING GASOLINE (AZRBOB) GRADE 26 X6 6,7

ARIZONA CLEANER BURNING GASOLINE (ARZBOB) GRADE 30 X5 8,9

ARIZONA CLEANER BURNING GASOLINE (ARZBOB) GRADE 31 Z2 10

ARIZONA CLEANER BURNING GASOLINE (ARZBOB) GRADE 31 Z3 11

ARIZONA CLEANER BURNING GASOLINE (ARZBOB) GRADE 31 Z5 12,13 ARIZONA CLEANER BURNING GASOLINE (ARZBOB) GRADE 31 Z6 14,15

AVIATION JET FUEL

JP-8 GRADE MILITARY JET FUEL GRADE 05 16-20

QGRADE COMMERCIAL JET FUEL 21,22

CALIFORNIA GASOLINE

CARB PREMIUM GASOLINE GRADE 33 24



CONVENTIONAL GASOLINE BLENDSTOCKS

85 OCT INDEX CONVENTIONAL GASOLINE BLENDSTOCK (CBOB) 27,28

86 OCT INDEX CONVENTIONAL GASOLINE BLENDSTOCK (CBOB) 29,30

86 OCT INDEX CONVENTIONAL GASOLINE BLENDSTOCK (CBOB)

- GRADE 08 31,32

PREMIUM CONVENTIONAL GASOLINE BLENDSTOCK (PBOB) - 90 OCTANE 33,34

PREMIUM CONVENTIONAL GASOLINE BLENDSTOCK (PBOB)

- 91 OCTANE 35,36

PREMIUM CONVENTIONAL GASOLINE BLENDSTOCK (PBOB)

- GRADE 22 37,38

Central West

Product Specifications iii September 15, 2014

CONVENTIONAL GASOLINES Page

85 OCTANE CONVENTIONAL GRADE GASOLINE 39 86 OCTANE CONVENTIONAL GRADE GASOLINE 40,41 87 OCTANE CONVENTIONAL GRADE GASOLINE GRADE 03 42,43 90 OCTANE CONVENTIONAL GRADE GASOLINE 44,45 91 OCTANE CONVENTIONAL GRADE GASOLINE 46,47 93 OCTANE CONVENTIONAL GRADE GASOLINE GRADE 01 48,49

DISTILLATES

FUNGIBLE ULTRA LOW SULFUR DIESEL GRADE 37

50,51 LOW SULFUR HIGHWAY DIESEL FUEL GRADE 06 52,53 SEGREGRATED DISTILLATE BLENDSTOCK 54 SEGREGRATED DISTILLATE BLENDSTOCK GRADE 43 TEXAS X GRADE ULTRA LOW EMISSION DIESEL FUEL GRADE 49

55 90

LIQUIFIED PETROLEUM GAS

L GRADE PROPANE GRADE 12

56

REFORMULATED GASOLINE

93 OCTANE INDEX REFORMULATED GASOLINE

57,58

REFORMULATED GASOLINE BLENDSTOCKS

87 OCT INDEX REFORMULATED GASOLINE BLENDSTOCK (RBOB)

87 OCT INDEX REFORMULATED GASOLINE BLENDSTOCK (RBOB)

- GRADE 21

59,60

61,62

GRADE PREMIUM GASOLINE BLENDSTOCK (RBOB) 63,64 NR GRADE GASOLINE BLENDSTOCK (RBOB) GRADE 21 65,66 PREMIUM REFORMULATED GASOLINE BLENDSTOCK (RBOB)

PREMIUM REFORMULATED GASOLINE BLENDSTOCK (RBOB)

- GRADE 22

67,68

69,70,71

SPECIALTY PRODUCTS

LIGHT NAPHTHA

72

Central West

Product Specifications iv September 15, 2014

ADDITIVES Page

GASOLINE, FUEL OIL AND DIESEL FUEL ADDITIVE SPECIFICATIONS 73,74

GASOLINE VOLATILITY SCHEDULES

AMARILLO 8” PIPELINE - PREMIUM UNLEADED GASOLINE 75

AMARILLO 8” PIPELINE - REGULAR UNLEADED GASOLINE 76

COLORADO SPRINGS PIPELINE – PREMIUM UNLEADED GASOLINE 77

COLORADO SPRINGS PIPELINE – REGULAR UNLEADED GASOLINE 78

EL PASO PIPELINE – PREMIUM UNLEADED GASOLINE 79 EL PASO PIPELINE – REGULAR UNLEADED GASOLINE 80

LAREDO PIPELINE – PREMIUM UNLEADED GASOLINE 81

LAREDO PIPELINE – REGULAR UNLEADED GASOLINE 82

SAN ANTONIO EAST PIPELINE – PREMIUM UNLEADED GASOLINE 83

SAN ANTONIO EAST PIPELINE – REGULAR UNLEADED GASOLINE 84

SAN ANTONIO SOUTH PIPELINE – PREMIUM UNLEADED GASOLINE 85 SAN ANTONIO SOUTH PIPELINE – REGULAR UNLEADED GASOLINE 86

V- SEASONAL GASOLINE VOLATILITY CLASSES 87

VALLEY PIPELINE – PREMIUM UNLEADED GASOLINE 88

VALLEY PIPELINE – REGULAR UNLEADED GASOLINE 89

Central West Products Shipped by Pipeline System

Product Name TOC Category Shipped on CW Pipeline System CW Pipeline Systems 84 OCTANE CONVENTIONAL GASOLINE - TUSCON Arizona Gasolines 9 Aberathy/Lubbock Pipeline 1

ARIZONA CLEANER BURNING GASOLINE (CBG) GRADE 30 PRODUCT CODE X2 Arizona Gasolines 9 Albuquerque Pipeline 2 ARIZONA CLEANER BURNING GASOLINE (CBG) GRADE 30 PRODUCT CODE X3 Arizona Gasolines 9 Amarillo - 6" Pipeline 3

ARIZONA CLEANER BURNING GASOLINE AZRBOB GRADE 26 PRODUCT CODE X6 Arizona Gasolines 9 Amarillo - 8" Pipeline 4 ARIZONA CLEANER BURNING GASOLINE AZRBOB GRADE 30 PRODUCT CODE X5 Arizona Gasolines 9 Borger-Denver Pipeline 5 ARIZONA CLEANER BURNING GASOLINE AZRBOB GRADE 31 PRODUCT CODE Z2 Arizona Gasolines 9 Burgos Pipeline 6 ARIZONA CLEANER BURNING GASOLINE AZRBOB GRADE 31 PRODUCT CODE Z3 Arizona Gasolines 9 Colorado Springs- Denver Pipeline 7 ARIZONA CLEANER BURNING GASOLINE AZRBOB GRADE 31 PRODUCT CODE Z5 Arizona Gasolines 9 Corpus Christi Chemical Pipeline 8 ARIZONA CLEANER BURNING GASOLINE AZRBOB GRADE 31 PRODUCT CODE Z6 Arizona Gasolines 9 El Paso Pipeline 9

JP-8 GRADE MILITARY JET FUEL GRADE 05 Aviation/Jet Fuel 13 Laredo Pipeline 11 Q GRADE COMMERCIAL JET FUEL Aviation/Jet Fuel 2,4,5,7 San Antonio South Pipeline 12

T GRADE TURBINE FUEL GRADE 14 Aviation/Jet Fuel 1,2,4,5,7,8,12,13 Southlake Pipeline 13 CARB PREMIUM GASOLINE GRADE 36 California Gasolines 9 TR-Pettus-SA East Pipeline 14 CARB REGULAR GASOLINE GRADE 33 California Gasolines 9 Valley Pipeline 15 CARB REGULAR GASOLINE GRADE 34 California Gasolines 9

85 OCTANE INDEX CONVENTIONAL GASOLINE BLENDSTOCK (CBOB) Conventional Gasoline Blendstocks 4,5,7 86 OCTANE INDEX CONVENTIONAL GASOLINE BLENDSTOCK (CBOB) Conventional Gasoline Blendstocks 1,9

87 OCTANE INDEX CONVENTIONAL GASOLINE BLENDSTOCK (CBOB) – GRADE 08 Conventional Gasoline Blendstocks 11,12,14 PREMIUM CONVENTIONAL GASOLINE BLENDSTOCK (PBOB) – 90 OCTANE Conventional Gasoline Blendstocks 1,4 PREMIUM CONVENTIONAL GASOLINE BLENDSTOCK (PBOB) – 91 OCTANE Conventional Gasoline Blendstocks 2,4,5,7 PREMIUM CONVENTIONAL GASOLINE BLENDSTOCK (PBOB) – GRADE 22 Conventional Gasoline Blendstocks 11,12,14

85 OCTANE CONVENTIONAL GRADE GASOLINE Conventional Gasolines 5,7 86 OCTANE CONVENTIONAL GRADE GASOLINE Conventional Gasolines 1,4,9

87 OCTANE INDEX CONVENTIONAL GASOLINE GRADE 03 Conventional Gasolines 11,12,15 90 OCTANE CONVENTIONAL GRADE GASOLINE Conventional Gasolines 1,4,15 91 OCTANE CONVENTIONAL GRADE GASOLINE Conventional Gasolines 1,2,4

93 OCTANE INDEX CONVENTIONAL GASOLINE GRADE 01 Conventional Gasolines 11,12,15 FUNGIBLE ULTRA LOW SULFUR FUEL DIESEL GRADE 37 Distillates 1,2,3,4,5,7,9,13

LOW SULFUR HIGHWAY DIESEL FUEL GRADE 06 Distillates 12 SEGREGATED DISTILLATE BLENDSTOCK Distillates 8

L GRADE PROPANE GRADE 12 Liquified Petroleum Gas 9,11 93 OCTANE INDEX REFORMULATED GASOLINE Reformulated Gasoline 13

87 OCTANE INDEX REFORMULATED GASOLINE BLENDSTOCK (RBOB) Reformulated Gasoline Blendstocks 13 87 OCTANE INDEX REFORMULATED GASOLINE BLENDSTOCK (RBOB) GRADE 21 Reformulated Gasoline Blendstocks 13

GRADE PREMIUM GASOLINE BLENDSTOCK (RBOB) Reformulated Gasoline Blendstocks 13 NR GRADE GASOLINE BLENDSTOCK (RBOB) GRADE 21 Reformulated Gasoline Blendstocks 13

PREMIUM REFORMULATED GASOLINE BLENDSTOCK (RBOB) Reformulated Gasoline Blendstocks 13 PREMIUM REFORMULATED GASOLINE BLENDSTOCK (RBOB) – GRADE 22 Reformulated Gasoline Blendstocks 13

LIGHT NAPHTHA Specialty Products 6,15

Central West

Pipeline Specifications v December 1, 2011

Central West

Product Specifications Page 1 December 1, 2011

SPECIFICATIONS FOR 84 OCTANE CONVENTIONAL GASOLINE - TUCSON

84TUC

Product code H6 thru H9 (1) (2) (3)

Product Codes 6H thru 9H (1) (2) (3)

ASTM Origin

Test Shipments Deliveries Specification Points Method Minimum Maximum (At Terminals) Gravity, Degrees API D287 Report Only Color Undyed Volatility, (EPA formula) D4953 (1) D5191 Distillation, deg F D86

End point, F 437 Mercaptan Sulfur, wt % 2/ D3227 0.004 Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5 Oxidation Stability, min. D525 240 180 Phosphorous, g/gal D3231 0.003 0.005 Lead, g/gal D3237 0.030 0.05 Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 84.0 Sulfur, ppm D2622 80* Haze rating 3/ D4176 2 3 NACE Corrosion TM0172 B+

Central West


SPECIFICATIONS FOR 84 OCTANE CONVENTIONAL GASOLINE - TUCSON

84TUC

*NOTE: Registered Small Refiners may ship SRGAS with a sulfur content not to exceed their

permissible cap per EPA regulations. SRGAS product codes will be the Numeric/Alpha reverse of

their low sulfur counterparts. SRGAS may be delivered fungible with its low sulfur counterpart

(i.e., H9=9H, etc.).

1/ RVP: H6/6H = 10.00, H7/7H = 11.5, H8/8H = 13.5, H9/9H = 9.0

2/ Mercaptan Sulfur determination is waived if the result of the Doctor Test ASTM D4952 is negative.

3/ Compliance with ASTM D4176 will be determined using Procedure 2 at the following temperatures, adjusted

seasonally: February 16 – September 30 55 F max

October 1 – February 15 45 F max

In addition to the above specifications, product must meet latest revision of ASTM D4814.

Maximum oxygen content is 0.05 weight%.

Rev. 2 03/29/2011

Central West


ASTM Origin

Test Shipments Deliveries

Specification Points Method Minimum Maximum (At Terminals)

Gravity, Degrees API D287 Report Only Color Undyed Volatility D4953 6.40 7.00

D5191 Distillation, deg F D86

E200 30% 70% E300 70% 100% End point, F 437

Mercaptan Sulfur, wt % 1/ D3227 0.004 Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5

Oxidation Stability, min. D525 240 180

Phosphorous, g/gal D3231 0.003 0.005

Lead, g/gal D3237 0.030 0.05

Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 87.0 Sulfur, ppm D2622 80 Aromatics, vol % D5580 50% Olefins, vol % D4815 25% Oxygenates, wt % D4815 0.05 Haze rating 2/ D4176 2 3

NACE Corrosion TM0172 B+

SPECIFICATIONS FOR ARIZONA CLEANER BURNING GASOLINE (CBG)

GRADE 30 - Product code X2 (1) (2)

Central West


SPECIFICATIONS FOR ARIZONA CLEANER BURNING GASOLINE (CBG) 1/ Mercaptan Sulfur determination is waived if the result of the Doctor Test

ASTM D4952 is negative.

2/ Compliance with ASTM D4176 will be determined using Procedure 2 at the following

temperatures, adjusted seasonally:

February 16 – September 30 55 F max



Rev. 1

3/13/09

Central West


SPECIFICATIONS FOR ARIZONA CLEANER BURNING GASOLINE (CBG)

GRADE 30 - Product code X3 (1)

ASTM Origin



Gravity, Degrees API D287 Report Only Color Undyed Volatility D4953 8.00

D5191 Distillation, deg F D86

E200 30% 70% E300 70% 100% End point, F 437




Lead, g/gal D3237 0.030 0.05

Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 87.0 Sulfur, ppm D2622 80 Aromatics, vol % D5580 50% Olefins, vol % D4815 25% Oxygenates, wt % D4815 0.05 Haze rating 2/ D4176 2 3




seasonally:



In addition to the above specifications, product must meet latest revision of ASTM D4814. Rev. 1 3/13/09

Central West


SPECIFICATIONS FOR ARIZONA CLEANER BURNING GASOLINE

AZRBOB

GRADE 26 - Product code X6 (1) (2) (3)

ASTM Origin

Test Shipments Deliveries Specification Points Method Minimum Maximum (At Terminals) Gravity, Degrees API D287 Report Only Color Undyed Volatility D4953 8.00 D5191 Distillation, deg F D86

T50 237 T90 335 End point, F 437

Mercaptan Sulfur, wt % 1/ D3227 0.004 Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5 Oxidation Stability, min. D525 240 180 Phosphorous, g/gal D3231 0.003 0.005 Lead, g/gal D3237 0.030 0.05 Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 84.0 Sulfur, ppm D2622 89 Aromatics, vol % D5580 33.1 Olefins, vol % D4815 11.1 Oxygenates, wt % D4815 0.05 Haze rating 2/ D4176 2 3 NACE Corrosion TM0172 B+

Central West



AZRBOB




October 1 – February 15 45 F max In addition to the above specifications, product must meet latest revision of ASTM D4814.

AZRBOB does not comply with the standards for Arizona CBG without the addition of oxygenate.

This AZRBOB is intended for blending with 10 vol% ethanol and may not be combined with AZRBOBs requiring oxygenate

blending with any other type or amount of oxygenate.

Rev. 1 3/13/09

Central West



AZRBOB

GRADE 30 - Product code X5 (1) (2)

ASTM Origin


T50 237 T90 335 End point, F 437



AZRBOB




October 1 – February 15 45 F max In addition to the above specifications, product must meet latest revision of ASTM D4814.

For shipment in the Spring transition only.




Rev. 1

3/13/09

Central West Product Specifications Page 9 December 1, 2011

December 1, 2011

Central West

Product Specifications Page 10

SPECIFICATIONS FOR PREMIUM ARIZONA CLEANER BURNING GASOLINE

AZRBOB

GRADE 31 - Product code Z2 (1)

ASTM Origin Test Shipments Deliveries

Specification Points Method Minimum Maximum (At Terminals) Gravity, Degrees API D287 Report Only Color Undyed Volatility D4953 6.4 7.00 D5191 Distillation, deg F D86

E200 30% 70% E300 70% 100% End point, F 437

Mercaptan Sulfur, wt % 1/ D3227 0.004 Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5 Oxidation Stability, min. D525 240 180 Phosphorous, g/gal D3231 0.003 0.005 Lead, g/gal D3237 0.030 0.05 Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 91.0 Sulfur, ppm D2622 80 Aromatics, vol % D5580 50 Olefins, vol % D4815 25 Oxygenates, wt % D4815 0.05 Haze rating 2/ D4176 2 3 NACE Corrosion TM0172 B+






Rev. 2 03/29/2011

December 1, 2011

Central West



AZRBOB

GRADE 31 - Product code Z3 (1) (2)


Specification Points Method Minimum Maximum (At Terminals) Gravity, Degrees API D287 Report Only Color Undyed Volatility D4953 8.00 D5191 Distillation, deg F D86

E200 30% 70% E300 70% 100% End point, F 437

Mercaptan Sulfur, wt % 1/ D3227 0.004 Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5 Oxidation Stability, min. D525 240 180 Phosphorous, g/gal D3231 0.003 0.005 Lead, g/gal D3237 0.030 0.05 Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 91.0 Sulfur, ppm D2622 80 Aromatics, vol % D5580 50 Olefins, vol % D4815 25 Oxygenates, wt % D4815 0.05 Haze rating 2/ D4176 2 3 NACE Corrosion TM0172 B+






Rev. 2 03/29/2011

December 1, 2011

Central West



AZRBOB

GRADE 31 - Product code Z5 (1) (2) (3) (4)

ASTM Origin


T50 237 T90 335 End point, F 437







For shipment in Spring and Fall transitions only.


AZRBOB




Rev. 1

3/13/09



AZRBOB

GRADE 31 - Product code Z6 (1) (2) (3)

ASTM Origin


T50 237 T90 335 End point, F 437




seasonally:






December 1, 2011

Central West



AZRBOB



Rev. 2

03/29/2011

December 1, 2011

Central West


Gravity, API D287 37.0 51.0

Density, kg/L at 60F D4052 0.775 0.840

Total Acid Number, mg KOH/g D3242 0.015

Freezing Point, F D2386 -52

Existent Gum, mg/100ml D381 7.0

Sulfur, ppm D2622 3000

Mercaptan Sulfur, wt.% D3227 0.002

Doctor Test D4952 Negative

Color, Saybolt D156 Report

Corrosion, Copper D130 1

Water Separation Index D3948 1/ Water Reaction, Interface Rating D1094 1b

Aromatics, vol. % D1319 25.0

Flash Point, F D93 100 Viscosity @ -4 F, cSt D445 8.0

Electrical Conductivity, pSm D2624 2/ 2/

Thermal Stability; D3241 3/ Filter pressure drop, mm Hg. 25 Heater tube deposit rating < 3

Distillation, F @ 760 mm Hg D86 Initial Boiling Point, F Report 10% Recovered, F 401 20% Recovered, F Report 50% Recovered, F Report 90% Recovered, F Report Final Boiling Point, F 572 Residue, Vol. % 1.5 Loss, Vol. %

OR 1.5

Simulated Distillation D2887 Initial Boiling Point, F Report 10% Recovered, F 401 20% Recovered, F Report 50% Recovered, F Report

SPECIFICATIONS FOR JP-8 GRADE MILITARY JET FUEL

Grade 05

ASTM Shipments Deliveries

Test (At Origin) (At Terminals)

Specification Points Methods Minimum Maximum May Be*

December 1, 2011

Central West



Grade 05

90% Recovered, F Report

Final Boiling Point, F 572

Net Heat of Combustion, BTU/lb D3338 18,400

OR: MJ/kg D4809 42.8

Combustion

(1) Smoke Point, mm D1322 25.0

OR

(2) Smoke Point, mm D1322 19.0 3.0 AND Napthalenes vol. % D1840

Hydrogen Content, wt % D3701 13.4

Cetane Index D976 Report Particulate Matter, mg/L D5452 4/ 1.0

Filtration Time, minutes 15

Fuel System Icing Inhibitor, vol % D5006 5/ 0.10 0.15

1/ The minimum microseparometer rating shall be as follows:

J8 Additives MSEP Rating, min.

Antioxidant (AO)*, Metal Deactivator (MDA)* 90

AO*, MDA*, and Fuel System Icing Inhibitor (FSII) 85

AO*, MDA*, and Corrosion Inhibitor/Lubricity Improver (CI/LI) 80

AO*, MDA*, FSII and CI/LI 70

* Even though the presence or absence does not change these limits, samples submitted

for specification conformance testing shall contain the same additives present in the

refinery batch. Regardless of which minimum the refiner elects to meet, the refiner shall

report the MSEP rating on a laboratory hand blend of the fuel with all additives required

by the specification.

2/ The conductivity must be between 150 and 450pS/m at ambient temperature or 85 F,

whichever is lower (150 to 700 for JP8+100 shipments that contain thermal stability

improver additive), unless otherwise directed by the procuring activity.

3/ ASTM D3241 Thermal Stability test must be conducted at 260 C for 2.5 hours.

Peacock or abnormal color deposits result in a failure and are not accepted.

December 1, 2011

Central West



Grade 05 4/ A minimum sample size of 3.79 liters (one gallon) shall be filtered. Filtration time will

be determined in accordance with the procedure in Appendix A of MIL-DTL-83133E (or

most current version); this procedure may be used to determine the particulate matt er as

an alternate to ASTM D5452 or ASTM D2276.

5/ FSII test shall be performed using the DiEGME scale of the refractometer.

Other Requirements

Additives: Shipper must provide the type and amount of each additive used upon request.

Antioxidants: Immediately after processing, and before the fuel is exposed to the atmosphere

(i.e. during rundown into feed/batch tankage), add an approved antioxidant from the following list in order to prevent the formation of gums and peroxides after manufacture. The

concentration of antioxidant to be added shall be:

a. Not less than 17.2 mg or more than 24.0 mg of active ingredient per liter of fuel (6.0

to 8.4 lb/1000 barrels) to all JP-8 fuel that contains blending stocks that have been

hydrogen treated.

b. At the option of the supplier, not more than 24.0 mg of active ingredient per liter of

fuel (8.4 lb/1000 barrels) may be added to JP-8 fuels that do not contain hydrogen

treated blending stocks.

Approved Antioxidants

a. 2, 6-di-tert-butyl-4-methylphenol

b. 6-tert-butyl-2, 4-dimethylphenol

c. 2, 6-di-tert-butylphenol

d. 75% minimum: 2, 6-di-tert-butylphenol

25% maximum: tert-butyl phenols and tri-tert-butylphenols

e. 72% minimum: 6-tert-butyl-2, 4-dimethylphenol

28% maximum: tert-butyl-methylphenols and tert-butyl dimethylphenols

f. 55% minimum: 2, 4-dimethyl-6-tert-butylphenol and 15% minimum: 2, 6-di-tert-butyl—4-methylphenol and

30% maximum: mixed methyl and dimethyl tert-butylphenols

Metal Deactivator: A metal deactivator, N,N’-disalycylidene-1, 2-propanediamine, may be

blended into the fuel. The concentration of active material used on initial batching of the fuel at

December 1, 2011

Central West



Grade 05 the refinery shall not exceed 2.0 mg/L. Cumulative addition of metal deactivator when redoping

the fuel shall not exceed 5.7 mg/L. Metal deactivator additive shall not be used in JP -8 unless

the supplier has obtained written consent from the Procuring Activity and user.

Static Dissipater Additive: An additive shall be blended into the fuels in sufficient

concentration to increase the conductivity of the fuel to within the range specified in the

specifications at the point of injection. The point of injection of the additive shall be determined

by agreement between the purchasing authority and the supplier. The following electrical

conductivity additive is approved: Statis 450 marketed by Octel America Inc., Newark, DE

19702.

Corrosion Inhibitor: A corrosion inhibitor conforming to MIL-PRF-25017 shall be blended

into the F-34 (JP-8) grade fuel by the contractor. The corrosion inhibitor additive is optional for

F-35. The amount added shall be equal or greater than the minimum effective concentration an d

shall not exceed the maximum allowable concentration listed in the latest revision of QPL-

25017. The contractor or transporting agency, or both, shall maintain and upon request shall

make available to the Government evidence that the corrosion inhibitors used are equal in every

respect to the qualification products listed in QPL-25017. The point of injection of the corrosion

inhibitor shall be determined by agreement between the Purchasing Authority and the supplier.

Fuel System Icing Inhibitor (FSII): the use of a fuel system icing inhibitor shall be mandatory

for NATO F-34 (JP-8) and shall conform to MIL-DTL-85470. the point of injection of the

additive shall be determined by agreement between the Purchasing Authority and the supplier.

Thermal Stability Improver Additive: Due to logistical concern, personnel at the operating

location shall request written approval from the cognizant activity to add a thermal stability

improver additive to the fuel. If approval is given, the concentration of the a dditive and location

of injection shall be specified by the cognizant service activity found in MIL-DTL-8133E section

3.3.6. JP-8 fuel with an approved thermal stability improver additive at the required

concentration shall be designated as JP-8+100. Thermal stability improver additive shall not be

used in JP-8 without approval, in writing (reference MIL-DTL-83133E section 3.3.6 for

addresses).

December 1, 2011

Central West



Grade 05

Qualified thermal stability improver additives:

Qualification

Additive name Reference Manufacturer

SPEC AID 8Q462 AFRL/PRSF BetzDeraborn

Ltr, 9 Dec 97 9669 Grogan Mill Road

PO Box 4300

The Woodlands, TX 77387

AeroShell Performance AFRL.PRSF Shell Aviation

Additive 101 Ltr, 13 Jan 98 Shell-Mex House

Strand

London WC2R 0ZA

Premixing of Additives: Additives shall not be premixed with other additives before injection

into the fuel so as to prevent possible reactions among the concentrated forms of different

additives.

Workmanship: At the time of Government acceptance, the finished fuel shall be visually free

from undissolved water, sediment, or suspended matter and shall be clear and bright.

Additional Provisions: The Carrier shall not be responsible for the concentrations of additives

in JP-8 grade jet fuel deliveries except as provided for in the tariff.

Rev. 1 3/13/09

SPECIFICATION FOR Q GRADE COMMERCIAL JET FUEL



Specification Points Methods Minimum Maximum May Be*

Gravity, API D287 37.5 50.5 0.5 lower

or higher

Acidity, Total, Mg KOH/g D3242 0.1

Freezing Point, F D2386, D5972 -40

Existent Gum, mg/100ml D381 5 7

Sulfur, Total, ppm D2622 3000

Mercaptan Sulfur, ppm 1/ D3227 30

Color, Saybolt D156 +16 +14

Corrosion, Copper D130 1

2 hours @ 212 F

Water Separation Index D3948 85 75

Water Reaction, D1094

Volume Change, ml +1

Interface Rating 1b

Aromatics, vol. % D1319 25

Net Heat of Combustion, BTU/lb 2/ D4809 18,400 D3338, D4529

Flash Point, F D56 108 100

Viscosity @ -4 F, cSt D445 8

Electrical Conductivity, pSm D2624 Report

Thermal Stability; D3241 3/ 4/

Filter pressure drop, mm Hg. 25

Heater tube rating < 3

Distillation, F @ 760 mm Hg D86

10% Recovered, F 396 400



Final Boiling Point, F 562 572

Residue, Vol. % 1.5

Loss, Vol. % 1.5

OR

Simulated Distillation D2887

10% Recovered, F 365





SPECIFICATION FOR Q GRADE COMMERCIAL JET FUEL Combustion

(1) Smoke Point, mm D1322 25

OR

(2) Smoke Point, mm D1322 18

AND Napthalenes vol. % D1840 3.0

Particulate Matter D5452 Report

1/ The Mercaptan Sulfur determination may be waived if the result of a Doctor Test by


2/ Equation 2 in D3338 may be used as an alternate method.

3/ ASTM D3241 Thermal Stability test must be conducted at 262 C for 2.5 hours at origin.

Peacock or abnormal color deposits result in a failure and are not accepted.

4/ ASTM D3241 Thermal Stability test results for deliveries will be generated at a

minimum test temperature of 260 C.

Additives:

Antioxidants: Shipments may, but are not required to, contain a maximum of 8.4 pounds

per 1,000 barrels (not including weight of solvent) of the following anti -oxidants:

(1) N, N-diisopropylparaphenylene diamine.

(2) 75% (min) of 2, 6-ditertiary-butyl phenol plus 25% (max) of tertiary and

tritertiary butyl phenols.

(3) 72% (min) 2, 4-dimethyl-6-tertiary-butyl phenol plus 28% (max) of monomethyl

and dimethyl tertiary-butyl phenols.

(4) 55% (min) 2, 4-dimethyl-6-tertiary-butyl phenol plus 45% (max) of mixed tertiary

and ditertiary butyl phenols.

Metal Deactivators: Shipments may, but are not required to, contain the following metal

deactivators at a maximum of 2.0 lbs per 1,000 barrels (not including weight of solvent):

(1) n, N-disalicylidene-1, 2-propane diamine.

No other additives are permitted.

The carrier shall not be responsible for the concentration of additives in jet fuel deliveries at

terminals.

Rev.1

3/13/09


Central West

Product Specifications

Page 23 December 1, 2011

SPECIFICATION FOR T GRADE TURBINE FUEL

Grade 14 ASTM Shipments Deliveries


Specification Points Methods Minimum Maximum May Be* Gravity, API D287 37.0 51.0

Freezing Point, F D2386 -40

Existent Gum, mg/100ml D381 7 Sulfur, ppm D2622 3000

Corrosion, Copper D130 1 Water Separation Index D3948 85

Flash Point, F D56 105 100

Distillation, F @ 760 mm Hg D86 Initial Boiling Point, F Report

10% Recovered, F 401 20% Recovered, F Report

50% Recovered, F Report 90% Recovered, F Report


Residue, Vol. % 1.5

Loss, Vol. % 1.5

OR Simulated Distillation D2887

Initial Boiling Point, F Report

10% Recovered, F 401 20% Recovered, F Report

50% Recovered, F Report 90% Recovered, F Report


Particulate Matter, mg/L D5452 1/ 2.0 Workmanship Clear and Bright

1/ A minimum sample size of 3.79 liters (one gallon) shall be filtered. Filtration time will be

determined in accordance with the procedure in Appendix A of MIL-DTL-83133E (or most

current version); this procedure may be used to determine the particulate matter as an alternate to

ASTM D5452 or ASTM D2276.

In addition to above specifications, product must meet ASTM D1655 latest revision.

Any included additives approved for use in ASTM D1655 must be declared by type and volume.

Rev. 1

3/13/09

Central West


SPECIFICATIONS FOR CARB REGULAR GASOLINE

Grade 33

This product requires the addition of 5.7 vol.% ethanol.

ASTM Origin

Test 1/ Shipments Deliveries Specification Points Method Minimum Maximum (At Terminals) Gravity, Degrees API D287 Report Only Color Undyed

Volatility 2/ D323 12.5 - Jan. 1st

5.99 - Feb. 1st

10.5 - Nov. 1st

12.5 - Dec. 1st

Distillation, degrees F D86-99ae1 Feb 1st

Nov.1st

Dec 1st

T50, max 232 237 237 T90, max 335 335 335

End point, max 437 437 437 Phosphorous, g/gal D3231 0.005

Lead, g/gal D3237 0.030

Research Octane {R} D2699 Report

Motor Octane {M} D2700 Report

(R+M)/2 D4814 87.0 Benzene, vol.% D5580-95 1.22

Aromatic HC, vol.% D5580-00 38.7 Olefins, vol.% D4815-99 0.025

Sulfur, ppm D2622-94 32

D5453-93 Oxygen, wt % D4815-99 0.25

Haze rating 4/ D4176 2 3 Odor 3/ Nonoffensive

1/ California Air Resources Board Regulations.

2/ Grabner-CA equation (RVPE psi = 0.972 * ptot – 0.71)

3/ Any gasoline exhibiting an offensive odor and/or containing more than 0.30 wt % dicyclopentadiene will

not be accepted for shipment.

4/ In addition to Nustar specifications, product must meet latest revision of ASTM D4814.

Rev. 1

3/13/09

Central West

Product Specifications Page 25 December 1

SPECIFICATIONS FOR CARB SUBGRADE GASOLINE

Grade 34


ASTM Origin Test 1/ Shipments Deliveries

Specification Points Method Minimum Maximum (At Terminals) Gravity, Degrees API D287 Report Only Color Undyed


5.99 - Feb. 1st

10.5 - Nov. 1st

12.5 - Dec. 1st


Nov.1st

Dec 1st

T50, max 232 237 237

T90, max 335 335 335


Lead, g/gal D3237 0.030



(R+M)/2 D4814 84.0 Benzene, vol.% D5580-95 1.22

Aromatic HC, vol.% D5580-00 38.7

Olefins, vol.% D4815-99 0.025


D5453-93

Oxygen, wt % D4815-99 0.25 Haze rating 4/ D4176 2 3

Odor 3/ Nonoffensive




not be accepted for shipment. 4/ In addition to Nustar specifications, product must meet latest revision of ASTM D4814.

Rev. 1

3/13/09

Central West


SPECIFICATIONS FOR CARB PREMIUM GASOLINE

Grade 36


ASTM Origin

Test 1/ Shipments Deliveries Specification Points Method Minimum Maximum (At Terminals) Gravity, Degrees API D287 Report Only Color Undyed


5.99 - Feb. 1st

10.5 - Nov. 1st

12.5 - Dec. 1st


Nov.1st

Dec 1st

T50, max 232 237 237 T90, max 335 335 335


Lead, g/gal D3237 0.030



(R+M)/2 D4814 90.0 Benzene, vol.% D5580-95 1.22

Aromatic HC, vol.% D5580-00 38.7 Olefins, vol.% D4815-99 0.025


D5453-93 Oxygen, wt % D4815-99 0.25

Haze rating 4/ D4176 2 3 Odor 3/ Nonoffensive





4/ In addition to Nustar specifications, product must meet latest revision of ASTM D4814.

Rev. 1

3/13/09

SPECIFICATIONS FOR 85 OCTANE INDEX CONVENTIONAL GASOLINE BLENDSTOCK

(CBOB)

For blending with 10% denatured fuel ethanol (92% purity) as defined by ASTM D4806.

This CBOB may not be combined with any other CBOB except CBOB having the same requirement for oxygenate type and amount.

All parameters must be met after blending with denatured fuel ethanol unless noted.

Requirements for both Segregated and Fungible:

ASTM Origin

Test Shipments Deliveries Specification Points Method Minimum Maximum (At Terminals) Note

Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 85.0 Oxygen Content, wt % D4815, D5599 , GC-OFID 0.1 1/ 2/ 7/

MTBE, vol.% D4815, D5599, GC-OFID 0.25 0.50 7/

DVPE D5191 3/

080, 008 8.0 081, 108 8.8 082, 208 10.0 083, 308 12.5 084, 408 14.5 085, 508 16.0

Fungible only requirements:

ASTM Origin



Benzene, vol % D3606 4.9

Gravity, Degrees API D287,D1298,D4052

Color

Report Only 7/

Undyed Doctor test D4952 Negative(sweet) 5/

or Mercaptan Sulfur, wt % D3227 0.002 Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5 Oxidation Stability, min. D525 240 180 Phosphorous, g/gal D3231 0.004 0.005 Lead, g/gal D3237 0.010 0.05

Central West


Central West


December 1, 2011


(CBOB)

Sulfur, ppm D2622 80 8/

NACE Corrosion TM0172 B+(Origin) 7/

Volatility: Driveability Index D4814 See chart Distillation, F @ % Evap. D86 See chart Vapor/Liquid Ratio (V/L), F @20 D5188 See chart 6/

Driveability 10 vol% 50 vol% 90vol% EndPt V/L

Grades Index Max Min Max Max Max Min

080,081,082 1250 158 150 250 374 430 120

083 1230 140 150 240 365 430 116

084 1220 131 150 235 365 430 107

085 1200 122 150 230 365 430 102

NOTES (Apply to Fungible and Segregated):

Heavy metals are not allowed.

This is a base gasoline, not for sale to the ultimate consumer. Any gasoline exhibiting an offensive odor and/or poses a personal health hazard will not be accepted for shipment.

Any gasoline exhibiting an offensive odor and/or containing more than 0.50 wt % dicyclopentadiene will not be accepted for

shipment.

The referee method will be based on a gas chromatograph test.

Delivery test results may vary by the smaller of ASTM reproducibility for a given test or any test tolerance as

allowed by state or EPA regulations at the point of delivery.

1/ All 08 grades may not contain oxygenates, such as ethers and alcohols. The use of non-hydrocarbon blending components in

these grades is prohibited.

2/ Refer to test methods published in 40 CFR Chapter 1, Part 80.46. Alternative aromatics and oxygenates test methods, ASTM

D1319 and D4815, may be used according to federal and state regulations.

3/ For products blended to meet EPA or state imposed summer VOC requirements, tests must be performed in accordance with the procedures described in 40 CFR, Part 80.

4/ Reserved

5/ Mercaptan sulfur waived if fuel is negative by Doctor Test.

6/ Computer and Linear methods may be used to determine V/L value. D5188 will be the referee method.

7/ Specifications must be met before blending of denatured fuel ethanol.

8/ Refer to 40 CFR Part 80.195 (d)(2). Alternate sulfur test methods, ASTM D5453 and D7039, may be used according to federal

and state regulations.

Rev. 2

03/28/11

mailto:@20

Central West


December 1, 2011

ASTM Origin





(CBOB)

For blending with 10% denatured fuel ethanol (92% purity) as defined by ASTM D4806. This CBOB may not be combined with any other CBOB except CBOB having the same requirement for oxygenate type and amount.



ASTM Origin


Research Octane {R} D2699 Report Motor Octane {M} D2700 82.0 (R+M)/2 D4814 86.0 Oxygen Content, wt % D4815, D5599 , GC-OFID 0.1 1/ 2/ 7/


DVPE D5191 3/

080, 008 7.8 081, 108 8.8 082, 208 10.0 083, 308 12.5 084, 408 14.5 085, 508 16.0



Color

Report Only 7/



Central West

Product Specifications December 1, 2011 Page 30


(CBOB)




Driveability 10 vol% 50 vol% 90vol% EndPt V/L(where applicable)


080,081,082 1250 158 150 250 374 430 120

083 1230 140 150 240 365 430 116

084 1220 131 150 235 365 430 107

085 1200 122 150 230 365 430 102



This is a base gasoline, not for sale to the ultimate consumer.

Any gasoline exhibiting an offensive odor and/or poses a personal health hazard will not be accepted for shipment.


shipment. The referee method will be based on a gas chromatograph test.







3/ For products blended to meet EPA or state imposed summer VOC requirements, tests must be performed in accordance with the

procedures described in 40 CFR, Part 80. 4/ Reserved


6/ Computer and Linear methods may be used to determine V/L value. D5188 will be the referee method. 7/ Specifications must be met before blending of denatured fuel ethanol.



Rev. 2

03/28/11

mailto:@20

Central West


ASTM Origin





(CBOB) – GRADE 08

For blending with 10% denatured fuel ethanol (92% purity) as defined by ASTM D4806. This CBOB may not be combined with any other CBOB except CBOB having the same requirement for oxygenate type and amount.



ASTM Origin


Research Octane {R} D2699 Report Motor Octane {M} D2700 82.0 (R+M)/2 D4814 87.0 Oxygen Content, wt % D4815, D5599 , GC-OFID 0.1 1/ 2/ 7/


DVPE D5191 3/

080, 008 8.0 081, 108 8.8 082, 208 10.0 083, 308 12.5 084, 408 14.5 085, 508 16.0



Color

Report Only 7/



Central West



(CBOB) – GRADE 08




Driveability 10 vol% 50 vol% 90vol% EndPt V/L(where applicable)


080,081,082 1250 158 150 250 374 430 120

083 1230 140 150 240 365 430 116

084 1220 131 150 235 365 430 107

085 1200 122 150 230 365 430 102






shipment. The referee method will be based on a gas chromatograph test.







3/ For products blended to meet EPA or state imposed summer VOC requirements, tests must be performed in accordance with the

procedures described in 40 CFR, Part 80. 4/ Reserved


6/ Computer and Linear methods may be used to determine V/L value. D5188 will be the referee method. 7/ Specifications must be met before blending of denatured fuel ethanol.



Rev. 2

03/28/2011

mailto:@20

December 1, 2011

Central West


SPECIFICATIONS FOR PREMIUM CONVENTIONAL GASOLINE BLENDSTOCK

(PBOB) – 90 OCTANE


This PBOB may not be combined with any other PBOB except PBOB having the same

requirement for oxygenate type and amount.



ASTM Origin



Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 90.0 Oxygen Content, wt % D4815, D5599 , GC-OFID 0.1 1/, 2/, 8/

MTBE, vol.% D4815, D5599, GC-OFID 0.25 0.50

DVPE 3/ D5191 220, 022 7.0 221, 122 7.8 222, 222 9.0 223, 322 11.5 224, 422 13.5 225, 522 15.0




Any gasoline exhibiting an offensive odor and/or containing more than 0.50 wt % dicyclopentadiene will not be

accepted for shipment.


Emissions reductions must be calculated using EPA guidelines.

December 1, 2011

Central West



(PBOB) – 90 OCTANE Fungible only requirements:


Specification Points Method Minimum Maximum (At Terminals) Gravity, Degrees API D287 Report Only 7/ Color Undyed Mercaptan Sulfur, wt % 4/ D3227 0.002 Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5 Oxidation Stability, min. D525 240 180 Phosphorous, g/gal D3231 0.004 0.005 Lead, g/gal D3237 0.010 0.05 Sulfur, ppm 5/ D2622 80 Haze rating 9/ D4176 2 3 NACE Corrosion TM0172 B+ Benzene, vol % D3606, D4053 4.9 Volatility: Driveability Index D4814 See chart Distillation, F @ % Evap. D86 See chart Vapor/Liquid Ratio (V/L), F @20 D5188 See chart 6/

Driveability 10 vol% 50 vol% 90vol% EndPt V/L(where applicable) Grades Index Max Min Max Max Max Min 220,221,222 1250 158 170 250 374 430 133 223 1230 140 170 240 365 430 124 224 1220 131 170 235 365 430 116 225 1200 122 170 230 365 430 105


1/ All 22 grades may not contain oxygenates, such as ethers and alcohols. The use of non-hydrocarbon blending

components in these grades is prohibited. 2/ Refer to test methods published in 40 CFR Chapter 1, Part 80.46. Alternative aromatics and oxygenates test methods,

ASTM D1319 and D4815, may be used according to federal and state regulations.

3/ For products blended to meet EPA or state imposed summer VOC requirements, tests must be performed in accordance

with the procedures described in 40 CFR, Part 80.

4/ Mercaptan sulfur determination is waived if the result of the Doctor Test ASTM D4952 is negative.

5/ Refer to 40 CFR Part 80.195 (d)(2). Alternate sulfur test methods, ASTM D5453 and D7039, may be used according

to federal and state regulations. 6/ Computer, Linear and Nomogram methods may be used to determine V/L value. D5188 will be the referee.

7/ Specifications must be met before blending of denatured fuel ethanol. 8/ Oxygen content must meet a minimum of 1.7 wt.% and a maximum of 4.0 wt.% after blending of denatured fuel

ethanol. 9/ Compliance with ASTM D4176 will be determined using Procedure 2 at the following temperatures, adjusted



Rev. 2 03/28/2011

mailto:@20

December 1, 2011

Central West



Specification Points Method Minimum Maximum (At Terminals) Gravity, Degrees API D287 Report Only 7/ Color Undyed Mercaptan Sulfur, wt % 4/ D3227 0.002 Hydrogen Sulfide D3227 None








ASTM Origin





DVPE 3/ D5191 220, 022 7.0 221, 122 7.8 222, 222 9.0 223, 322 11.5 224, 422 13.5 225, 522 15.0




Any gasoline exhibiting an offensive odor and/or containing more than 0.50 wt % dicyclopentadiene wi ll not be







Copper Corrosion D130 1

Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5 Oxidation Stability, min. D525 240 180 Phosphorous, g/gal D3231 0.004 0.005 Lead, g/gal D3237 0.010 0.05 Sulfur, ppm 5/ D2622 80 Haze rating 9/ D4176 2 3 NACE Corrosion TM0172 B+ Benzene, vol % D3606, D4053 4.9 Volatility: Driveability Index D4814 See chart Distillation, F @ % Evap. D86 See chart Vapor/Liquid Ratio (V/L), F @20 D5188 See chart 6/







with the procedures described in 40 CFR, Part 80. 4/ Mercaptan sulfur determination is waived if the result of the Doctor Test ASTM D4952 is negative.

5/ Refer to 40 CFR Part 80.195 (d)(2). Alternate sulfur test methods, ASTM D5453 and D7039, may be used according

to federal and state regulations.

6/ Computer, Linear and Nomogram methods may be used to determine V/L value. D5188 will be the referee.


8/ Oxygen content must meet a minimum of 1.7 wt.% and a maximum of 4.0 wt.% after blending of denatured fuel

ethanol.




Rev. 2 03/28/2011


mailto:@20

Central West


December 1, 2011


(PBOB) – GRADE 22






ASTM Origin





DVPE 3/ D5191 220, 022 7.0 221, 122 7.8 222, 222 9.0 223, 322 11.5 224, 422 13.5 225, 522 15.0









ASTM Origin Test Shipments Deliveries Specification Points Method Minimum Maximum (At Terminals) Gravity, Degrees API D287 Report Only 7/ Color Undyed Mercaptan Sulfur, wt % 4/ D3227 0.002

Central West


December 1, 2011


(PBOB) – GRADE 22

Hydrogen Sulfide D3227 None

Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5 Oxidation Stability, min. D525 240 180 Phosphorous, g/gal D3231 0.004 0.005 Lead, g/gal D3237 0.010 0.05 Sulfur, ppm 5/ D2622 80 Haze rating 9/ D4176 2 3 NACE Corrosion TM0172 B+ Benzene, vol % D3606, D4053 4.9 Volatility: Driveability Index D4814 See chart Distillation, F @ % Evap. D86 See chart Vapor/Liquid Ratio (V/L), F @20 D5188 See chart 6/







with the procedures described in 40 CFR, Part 80. 4/ Mercaptan sulfur determination is waived if the result of the Doctor Test ASTM D4952 is negative.

5/ Refer to 40 CFR Part 80.195 (d)(2). Alternate sulfur test methods, ASTM D5453 and D7039, may be used according to federal and state regulations.



8/ Oxygen content must meet a minimum of 1.7 wt.% and a maximum of 4.0 wt.% after blending of denatured fuel

ethanol.




Rev. 2 03/28/2011

mailto:@20

Central West


December 1, 2011

SPECIFICATIONS FOR 85 OCTANE CONVENTIONAL GRADE GASOLINE

(Conventional Gasoline - This product does not meet the requirements for reformulated gasoline and may not be

used in any reformulated gasoline covered area.)


Specification Points Method Minimum Maximum (At Terminals) Gravity, Degrees API D287 Report Only Color Undyed Volatility 1/ Mercaptan Sulfur, wt % 2/ D3227 0.004 Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5 Oxidation Stability, min. D525 240 180 Phosphorous, g/gal D3231 0.003 0.005 Lead, g/gal D3237 0.010 0.05 Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 85.0 Sulfur, ppm 3/ D2622 80 Oxygenates, wt % D4815 0.33 Haze rating 4/ D4176 2 3 NACE Corrosion TM0172 B+


1/ Refer to Seasonal Gasoline Volatility Schedule.

2/ Mercaptan Sulfur determination is waived if the result of the Doctor Test


3/ Gasoline exceeding the origin specification will be accepted from small refineries as defined in 40 CFR

part 80 of the EPA regulations.

4/ Compliance with ASTM D4176 will be determined using Procedure 2 at the following temperatures,

adjusted seasonally:





Rev. 1

10/21/10

Central West


December 1, 2011


(Conventional Gasoline - This product does not meet the requirements for reformulated gasoline

and may not be used in any reformulated gasoline covered area.)

ASTM Origin



Gravity, Degrees API D287 Report Only Color Undyed Volatility 1/ Mercaptan Sulfur, wt % 2/ D3227 0.004 Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5



Lead, g/gal D3237 0.010 0.05

Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 86.0 Sulfur, ppm 3/ D2622 80 Oxygenates, wt % D4815 0.33 Haze rating 4/ D4176 2 3

NACE Corrosion TM0172 B+ Odor 5/ Nonoffensive




3/ Gasoline exceeding the origin specification will be accepted from small refineries as

defined in 40 CFR part 80 of the EPA regulations.



Central West





5/ Any gasoline exhibiting an offensive odor and/or containing more than 0.30 wt %

dicyclopentadiene will not be accepted for shipment.

Rev. 1

10/21/10

Central West


December 1, 2011

SPECIFICATIONS FOR 87 OCTANE INDEX CONVENTIONAL GASOLINE

GRADE 03

This product does not meet requirements for reformulated gasoline, and may not be used in any reformulated

gasoline covered area.


ASTM

Test

Origin

Shipments

Deliveries Specification Points Research Octane {R}

Motor Octane {M}

Method D2699

D2700

Minimum Report

82.0

Maximum (At Terminals) Note

(R+M)/2 D4814 87.0

Oxygen Content, wt %

D4815,

D5599 , GC-OFID

0.1

1/

MTBE, vol.%

D4815,

D5599, GC-OFID

0.25

0.50

2/

DVPE

030, 003

D5191 7.0

3/

031, 103 7.8 032, 203 9.0 033, 303 11.5 034, 403 13.5 035, 503 15.0





shipment.


Delivery of any 03 grade to final destination in Virginia, and Maryland may contain MTBE.


Central West


December 1, 2011


GRADE 03

ASTM Origin


Gravity, Degrees API D287, D1298,D4052 Report Only Color Undyed Doctor test D4952 Negative(sweet) 4/

or Mercaptan Sulfur, wt % D3227 0.002 Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5 Oxidation Stability, min. D525 240 180 Phosphorous, g/gal D3231 0.004 0.005 Lead, g/gal D3237 0.010 0.05 Sulfur, ppm D2622 80 5/

NACE Corrosion TM0172 B+ Benzene, vol % D3606, D4053 4.9 Volatility: Driveability Index D4814 See chart Distillation, F @ % Evap. D86 See chart Vapor/Liquid Ratio (V/L), F @20 D5188 See chart 6/



030,031,032 1250 158 170 250 374 430 133

033 1230 140 170 240 365 430 124

034 1220 131 170 235 365 430 116

035 1200 122 170 230 365 430 105


1/ Non-oxygenated is defined as having no more than 0.1 wt.% oxygen. The use of oxygenated and/or non-

hydrocarbon blending components in these grades is prohibited.

2/ Delivery of any 03 grade to final destination s in Virginia, and Maryland may contain MTBE.

3/ For products blended to meet EPA or state imposed summer VOC requirements, tests must be performed in

accordance with the procedures described in 40 CFR, Part 80.

4/ Mercaptan sulfur waived if the fuel is negative by the Doctor Test.

5/ Refer to 40 CFR Part 80.195 (d)(2). Alternate sulfur test methods, ASTM D5453 and D7039, may be used

according to federal and state regulations.


Rev. 2

03/28/2011

mailto:@20

Central West


December 1, 2011




ASTM Origin






Lead, g/gal D3237 0.010 0.05












Central West


December 1, 2011




Rev. 1

10/21/10

Central West


December 1, 2011




ASTM Origin






Lead, g/gal D3237 0.010 0.05










Central West


December 1, 2011






Rev. 1

10/21/10

Central West


December 1, 2011


GRADE 01

This product does not meet requirements for reformulated gasoline, and may not be used in any

reformulated gasoline covered area.


ASTM Origin



Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 93.0 Oxygen Content, wt % D4815, D5599 , GC-OFID 0.1 1/


DVPE 3/ D5191 010, 001 7.0 011, 101 7.8 012, 201 9.0 013, 301 11.5 014, 401 13.5 015, 501 15.0







Delivery of any 01 grade to final destination in North Carolina, Virginia, and Maryland

may contain MTBE.


ASTM Origin Test Shipments Deliveries Specification Points Method Minimum Maximum (At Terminals) Gravity, Degrees API D287 Report Only Color Undyed


GRADE 01

Mercaptan Sulfur, wt % 4/ D3227 0.002

Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5 Oxidation Stability, min. D525 240 180 Phosphorous, g/gal D3231 0.004 0.005 Lead, g/gal D3237 0.010 0.05 Sulfur, ppm 5/ D2622 80 Haze rating 7/ D4176 2 3 NACE Corrosion TM0172 B+ Benzene, vol % D3606, D4053 4.9 Volatility: Driveability Index D4814 See chart Distillation, F @ % Evap. D86 See chart Vapor/Liquid Ratio (V/L), F @20 D5188 See chart 6/


Grades Index Max Min Max Max Max Min 011,012 1250 158 170 250 374 430 133 013 1230 140 170 240 365 430 124 014 1220 131 170 235 365 430 116 015 1200 122 170 230 365 430 105


1/ Non-oxygenated is defined as having no more than 0.1 wt.% oxygen. The use of oxygenated and/or non-

hydrocarbon blending components in these grades is prohibited.

2/ Delivery of any 01 grade to final destination s in North Carolina, Virginia, and Maryland may contain

MTBE.


accordance with the procedures described in 40 CFR, Part 80.

4/ Mercaptan sulfur determination is waived if the result of the Doctor Test ASTM D4952 is negative.



6/ Computer, Linear and Nomogram methods may be used to determine V/L value. D5188 will be the

referee.

7/ Compliance with ASTM D4176 will be determined using Procedure 2 at the following temperatures,

adjusted seasonally:



Rev. 2

03/28/2011


mailto:@20

(Ramsbottom) - Percent D524 0.35

Cloud Point, F D2500, D5771 2/

D5772, D5773 Pour Point, F D97, D5949 2/

D5950, D5985 Viscosity, cSt @104 F D445 1.9 4.1 Haze Rating 3/ D4176 2 3 Ash, wt % D482 0.01 Sulfur, ppm 4/ D2622 *10 15

NACE Corrosion TM0172 B+ Aromatics (Volume %) D1319 31.7 Or Aromatics by Cetane Index D976 40

SPECIFICATION FOR FUNGIBLE ULTRA LOW SULFUR FUEL DIESEL

GRADE 37



Specification Points Methods Minimum Maximum May Be Gravity, Degrees A.P.I. D287 30

Color D1500 2.5 3.0

Color visual Undyed

Distillation, D86



OR

Simulated distillation D2887



Corrosion, Copper Strip @122 F D130 1

Cetane Number D613 40 1/

Flash, F D93 130

Thermal Stability, 90 minutes

(1) 150C Pad rating,

DuPont scale 7

OR (2) Oxidation, mg/100ml D2274 2.5

Carbon Residue on 10% Bottoms


mailto:@104

mailto:@122

Central West Product Specifications Page 51

December 1, 2011

SPECIFICATION FOR FUNGIBLE ULTRA LOW SULFUR FUEL DIESEL

GRADE 37

BS&W, vol.% D2709 <0.05

Conductivity, pS/m @ 70 F D2624 250

1/ Where cetane number by test method D613 is not available, test method D4737B can be

used as an approximation.

2/ This schedule denotes the fluidity of the distillate at the time and place of origin.

Cloud point – August 1st

through March 14th

Maximum:

+15 F

Cloud point – March 15th

through July 31st

Maximum:

+20 F

Pour point – August 1st

through March 14th

Maximum:

0 F

Pour point – March 15th

through July 31st

Maximum:

+10 F

The referee method will be Cloud point D2500 and Pour point D97.

3/ The finished product shall be visually free of undissolved water, sediment, and suspended

matter in proffered tankage and at the point of delivery. Compliance with this

workmanship clause will be determined by ASTM D4176, Procedure 2 at 77 F or at

actual conditions present at the point and time of sampling, whichever is lower.

4/ Origin laboratory certifying sulfur content must qualify the test method used per EPA

Performance Based Testing Criteria (see CFR 80.584). The referee method will be

ASTM D5453. *Sulfur limit, 12 ppm for interconnecting pipelines.

Rev. 1

3/13/09

Central West Product Specifications Page 52

December 1, 2011

(Ramsbottom) - Percent D524

Cloud Point, F D2500, D5771 0.35

4/

D5772, D5773 Pour Point, F D97, D5949 4/

D5950, D5985 Viscosity, csT @104 F D445 1.9 3.4 Haze Rating 5/ D4176 2 3 Ash, wt % D482 0.01 Sulfur, ppm 6/ D2622, D5453 420 500

SPECIFICATION FOR LOW SULFUR HIGHWAY DIESEL FUEL

GRADE 06



Specification Points Methods Minimum Maximum May Be

Gravity, Degrees A.P.I. D287, D1298 30

D4052

Color ASTM D1500, D6045 2.5 3.0

Color Visual Undyed

Distillation, D86

50% Recovered, F Report 1/


End Point, F 690

OR

Simulated distillation D2887 1/



End Point, F 723

Corrosion, Copper Strip @122 F D130 1

Cetane Number D613 40 2/

Aromatics (Volume %) D1319 31.7

Or Aromatics by Cetane Index D976 40

Flash, F D93 130

Thermal stability, 90 minutes

150 C Pad rating,

DuPont scale 7

or

Oxidation stability,mg/100ml D2274 2.5

Carbon Residue on 10% Bottoms

mailto:@104

mailto:@122

Central West


December 1, 2011

SPECIFICATION FOR LOW SULFUR HIGHWAY DIESEL FUEL

GRADE 06

D7039


BS&W, vol.% D2709 <0.05


1/ Either physical or simulated distillation can be used. The referee test method will be

ASTM D86.

2/ Where cetane number by test method D613 is not available, test method D4737B can be

used as an approximation.

3/ The Potential Gum will be determined by ASTM Method D381 Modified (Steam Jet

Evaporated @ 485 F) after a 16 hour induction period by ASTM Method D525

Modified.

4/ This schedule denotes the fluidity of the distillate at the time and place of origin.

Cloud Point – August 1st

through March 14th

Maximum:

+15 F

Cloud Point – March 15th

through July 31st

Maximum:

+20 F

Pour Point – August 1st

through March 14th

Maximum:

0 F

Pour Point – March 15th

through July 31st

Maximum:

+10 F

The referee method will be Cloud point D2500 and Pour point D97.

5/ The finished product shall be visually free of undissolved water, sediment, and suspended

matter in proffered tankage and at the point of delivery. Compliance with this

workmanship clause will be determined by ASTM D4176, Procedure 2 at 77 F or at

actual conditions present at the point and time of sampling, whichever is lower.

6/ Origin laboratory certifying sulfur content must qualify the test method used per EPA

Performance Based Testing Criteria (see CFR 80.584). The referee test method will be

ASTM D5453.

Rev. 1

3/13/09

Central West


December 1, 2011

SPECIFICATION FOR SEGREGATED DISTILLATE BLENDSTOCK




Gravity, Degrees A.P.I. D287 37 51

Flash, F

D56, D3828

100

Sulfur, ppm

D2622, D5453

D7039, D4294

3000

1/

NACE Corrosion

TM0172

B+ (origin)

Conductivity, pS/m @ 70 F

D2624

Report

1/ Origin laboratory certifying sulfur content can qualify the test method used per EPA

Performance Based Testing Criteria (see CFR 80.584). The referee test method will be

ASTM D545.

Product shall be clear and bright and free of suspended matter.

Rev. 1

3/13/09

Central West


SPECIFICATION FOR SEGREGATED DISTILLATE BLENDSTOCK

GRADE 43




Gravity, Degrees A.P.I. D287, D1298 25 42

D4052

Flash, F D93 100

Sulfur, ppm 1/ D2622, D5453 10,000

D7039



Dye Requirement:

Origin: This product must exhibit visual evidence that red dye is present. The maximum allowable

concentration, or spectral equivalence, is 0.75 pounds of Solid Red #26 per 1,000 barrels. This product does not meet IRS excise tax requirements for dye.

Delivery: This product will be dyed by NuStar to meet a minimum dye concentration, or spectral

equivalence, of 3.9 pounds of Solid Red #26 per 1,000 barrels.

A waiver from Quality Assurance for the dye requirement will be given if the source and ultimate

destination are refineries.

This schedule denotes the fluidity of the distillate at the time and place of origin.

Cloud Point – August 1st

through March 14th

Cloud Point – March 15th

through July 31st

Maximum:

Maximum:

+15 F +20 F

Pour Point – August 1st

through March 14th

Maximum:

0 F Pour Point – March 15

th through July 31

st Maximum: +10 F

The referee method will be Cloud Point D2500 and Pour Point D97.

1/ Origin laboratory certifying sulfur content can qualify the test method used per EPA Performance

Based Testing Criteria (see CFR 80.584). The referee method will be ASTM D5453.

Rev. 2 03/30/2011

Central West


SPECIFICATION FOR L GRADE PROPANE

Grade 12


Test (At Origin) (From Terminals) Specification Points Methods Minimum Maximum 1/ Composition

Chromatograph analysis D2163

Percent by liquid volume: Propane 90 Propylene 5.0 Butanes and heavier 2.5 Pentanes and heavier None

Specific gravity, at 60/60 F D1657 0.500 0.510 Vapor pressure, psig at 100 F D1267 175 208 D2598, D6897 Weathering, 95% evaporated D1837 -37 Temp., F (corrected) Residues, D2158 Nonvolatile residue at 100 F, ml 0.05 Oil, no oil stain observation, ml 0.3 Sulfur, D2784,D6667 grains per hundred cubic feet 10 (or 123 ppmw) Corrosion, copper strip at 100 F D1838 No. 1 Dryness Valve freeze, seconds D2713 60

1/ Same as shipment specifications except for normal testing and handling tolerances.

Additives: L-grade propane shipments at origin shall be unstenched and contain no additives. Unless

otherwise notified in writing by shipper, L-grade propane deliveries will be odorized at the rate of 1 ½

pounds Ethyl Mercaptan/10,000 gallons.

Method of Inspection: Inspection shall be in accordance with MSTI, “Instructions Governing the

Measurement, Sampling and Testing of Products for Acceptance and Delivery,” currently in effect on

inspection date.

Rev.1

3/13/09

Central West


SPECIFICATIONS FOR 93 OCTANE INDEX REFORMULATED GASOLINE

ASTM Origin



Gravity, Degrees API D287 Report Only Color Undyed DVPE 1/ D5191

D3,3D,6D (Non-VOC controlled) 11.5 D4,4D,7D (Non-VOC controlled) 13.5 D5,5D,8D (Non-VOC controlled) 15.0 D1,1D,D2,2D (VOC controlled) Report 1/




Lead, g/gal D3237 0.010 0.05

Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 93.0 Sulfur, ppm 3/ D2622 80 Oxygen Content, wt % D5599 1.7 2.7 4/, 5/

Haze rating 6/ D4176 2 3

NACE Corrosion TM0172 B+ Benzene, vol % D3606 1.30 Aromatics, vol % D5599 50 5/

E200, vol % D86 30 70 E300, vol % D86 70 100 Olefins, vol % D1319 25 Emissions Performance Reductions, %

Region 1 (A1, 1A) -27 (-29 during cycles 14-21) -25

Region 2 (A2, 2A) -25.4 (-27.4 during cycles 14-21) -23.4

Odor 7/ Nonoffensive Volatility: Driveability Index D4814 See chart


Distillation, F @ % Evap. D86

Vapor/Liquid Ratio (V/L), F @20 8/

D2533, D5188



D1,D2 1250 158 170 250 374 430 133

D3,6D 1230 140 170 240 365 430 124

D4,7D 1220 131 170 235 365 430 116

D5,8D 1200 122 170 230 365 430 105


1/ For products blended to meet EPA or state imposed summer VOC requirements, tests

must be performed in accordance with the procedures described in 40 CFR, Part 80.



3/ Refer to 40 CFR Part 80.195 (d)(2). Alternate sulfur test methods, ASTM D5453 and

D7039, may be used according to federal and state regulations.

4/ Non-hydrocarbon blending components are to be reported on the certified laboratory

report by type and percent (by volume). This product is required to contain aliphatic

ether(s). The use of any other non-hydrocarbons, such as alcohols, as blending

components is prohibited.

5/ Refer to test methods published in 40 CFR Chapter 1, Part 80.46. Alternate aromatics

and oxygenates test methods, ASTM D1319 and D4815, may be used according to

federal and state regulations.







8/ Computer, Linear and Nomogram methods may be used to determine V/L value. D2533

will be the referee.

Rev. 1

3/13/09


mailto:@20

Central West


Region 1 (E1, 1E) -27 (-28 during cycles 14-21) -25

Region 2 (E2, 2E) -25.4 (-26.4 during cycles 14-21) -23.4


BLENDSTOCK (RBOB)

For Blending With 5.7% Denatured Fuel Ethanol (92% Purity) As Defined In ASTM D4806

ASTM Origin



Gravity, Degrees API D287 Report Only 1/

Color Undyed RVP 2/ D5191

E3, 3E (Non-VOC controlled) 11.5 E4, 4E (Non-VOC controlled) 13.5 E5, 5E (Non-VOC controlled) 15.0 E1,1E,E2,2E (VOC controlled) Report 2/, 6/




Lead, g/gal D3237 0.010 0.05

Research Octane {R} D2699 Report Motor Octane {M} D2700 82.0 (R+M)/2 D4814 87.0 Sulfur, ppm 4/ D2622 80 Oxygen Content, wt % D5599 5/, 6/, 10/



E200, vol % D86 30 70 E300, vol % D86 70 100 Olefins, vol % D1319 25 Emissions Performance Reductions, % 11/

December 1, 2011

Central West



BLENDSTOCK (RBOB)


Volatility:

Driveability Index D4814 See chart



D2533, D5188



E1,E2 1250 158 170 250 374 430 133

E3 1230 140 170 240 365 430 124

E4 1220 131 170 235 365 430 116

E5 1200 122 170 230 365 430 105



2/ For products blended to meet EPA or state imposed summer VOC requirements, tests must be

performed in accordance with the procedures described in 40 CFR, Part 80.



4/ Refer to 40 CFR Part 80.195 (d)(2). Alternate sulfur test methods, ASTM D5453 and D7039,

may be used according to federal and state regulations.

5/ All E grades may not contain oxygenates, such as ethers and alcohols. The use of non-

hydrocarbon blending components is prohibited. Origin maximum MTBE 0.25 vol.%. Delivery

maximum 0.50 vol.%.

6/ Refer to test methods published in 40 CFR Chapter 1, Part 80.46. Alternate aromatics and

oxygenates test methods, ASTM D1319 and D4815, may be used according to federal and state

regulations.





8/ Any gasoline exhibiting an offensive odor and/or containing more than 0.50 wt % dicyclopentadiene will not be accepted for shipment.

9/ Computer, Linear and Nomogram methods may be used to determine V/L value. D2533 will be

the referee. 10/ Oxygen content must meet a minimum of 1.7 wt.% and a maximum of 4.0 wt.% after blending

with denatured fuel ethanol. 11/ Emissions reductions must be calculated using EPA guidelines.

Revision date: 3/13/09

mailto:@20

December 1, 2011

Central West


Doctor test D4952 Negative(sweet) 5/

or Mercaptan Sulfur, wt % D3227 0.002 Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5

SPECIFICATIONS FOR 87 OCTANE INDEX REFORMULATED GASOLINE BLENDSTOCK

(RBOB)

GRADE 21

For Blending With 10% Denatured Fuel Ethanol (92% Purity) As Defined In ASTM D4806

All Grade 21 Requirements (Segregated and Fungible)

ASTM Origin


Benzene, vol % D3606 1.30 Research Octane {R} D2699 Report Motor Octane {M} D2700 82.0 (R+M)/2 D4814 87.0 Oxygen Content, wt % D5599,GC-OFID(See Note) 1/2/7/8/

Aromatics, vol % D5769,D5599,GC-OFID(See Note) 50 2/ E200, vol % D86 30 70

E300, vol % D86 70 100

Olefins, vol % D1319, D6550 25


Non-VOC Controlled Requirements

DVPE D5191 3/

213, 321 (Non-VOC controlled) 11.5

214, 421 (Non-VOC controlled) 13.5

215, 521 (Non-VOC controlled) 15.0 VOC Controlled Requirements DVPE D5191 3/

211,121,212,221 (VOC controlled) Report 2/ Emissions Performance Reductions, % 4/

Region 1 (211, 121) -27 -25 Region 2 (212, 221) -25.4 -23.4

Fungible Only Requirements: Color Undyed

December 1, 2011

Central West


SPECIFICATIONS FOR 87 OCTANE INDEX REFORMULATED GASOLINE BLENDSTOCK

(RBOB)

GRADE 21

Gravity API @ 60F D287,D1298,D4052 Report 7/



Lead, g/gal D3237 0.010 0.05

NACE Corrosion TM0172 B+ 7/




211,212 1250 158 170 250 374 430 133

213 1230 140 170 240 365 430 124

214 1220 131 150 235 365 430 116

215 1200 122 150 230 365 430 105


Heavy metals are not allowed to be present.


Any gasoline containing more than 0.50 wt.% of dicyclopentadiene will not be accepted for shipment.


Delivery test results may vary by the smaller of ASTM reproducibility for a given test or any test tolerance as allowed by

state or EPA regulations at the point of delivery.

1/ All 21 grades may not contain oxygenates, such as ethers and alcohols. The use of non -hydrocarbon blending

components is prohibited. Origin maximum MTBE 0.25 vol.%. Delivery maximum 0.50 vol.%.

2/ Refer to test methods published in 40 CFR Chapter 1, Part 80.46. Alternate aromatics and oxygenates test methods,



accordance with the procedures described in 40 CFR, Part 80. 4/ Emissions reductions must be calculated using EPA guidelines.

5/ Mercaptan Sulfur waived if fuel is negative by Doctor test.



8/ Oxygen content must meet a minimum of 1.7wt. % and a maximum of 4.0 wt. % after blending of denatured fuel

ethanol.

9/ Refer to 40 CFR Part 80.195 (d)(2). Alternative sulfur test methods, ASTM D5453 and D7039, may be used


Rev. 2

03/28/2011

mailto:@20

SPECIFICATIONS FOR AR GRADE PREMIUM GASOLINE BLENDSTOCK (RBOB)


ASTM Origin



Gravity, Degrees API D287 Report Only Color Undyed Volatility 1/ DVPE 2/ D5191 7.20 Mercaptan Sulfur, wt % 3/ D3227 0.004 Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5



Lead, g/gal D3237 0.010 0.05

Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 8/ D4814 91.3 (R+M)/2 (After blending) D4814 93.0 Benzene, wt. % D3606 1.3 Aromatics (vol %) 4/ 50 Olefins (vol %) D1319 25 Sulfur, ppm D2622 80 Oxygen Content wt% 5/ D5599 1.5 4.0 Oxygenates, wt % 8/ D4815 0.33 E200 (vol%) D86 30 70 E300(vol%) D86 70 100 Emission Performance Reduction (%) 27.0 Haze rating 6/, 8/ D4176 2 3

NACE Corrosion TM0172 B+ Odor 7/, 8/ Nonoffensive


SPECIFICATIONS FOR AR GRADE PREMIUM GASOLINE BLENDSTOCK (RBOB)


2/ For products blended to meet EPA or state imposed summer VOC requirements, test

must be performed for RVP in accordance with procedure described in 40 CFR, PART

80, Appendix E, Method 3.



4/ Refer to test methods in 40 CFR Chapter 1, Part 80.46.

5/ Oxygen content must meet a minimum of 1.5 wt. % and a maximum of 4.0 wt. % after

blending of denatured fuel ethanol.







8/ Specfications must be met before blending of denatured fuel ethanol

**NOTE: This RBOB may not be combined with any other RBOB except RBOB having

the same requirement for oxygenate type and amount. “Base Gasoline” Not for sale to the

ultimate consumer.

**NOTE: Heavy metals are not allowed to be present.

**NOTE: All parameters must be met after blending with denatured fuel ethanol unless noted.

Rev. 1

3/13/09


SPECIFICATIONS FOR NR GRADE GASOLINE BLENDSTOCK (RBOB)

Grade 21 For Blending With 10.0% Denatured Fuel Ethanol (92% Purity) As Defined In ASTM D4806

ASTM Origin



Gravity, Degrees API D287 Report Only Color Undyed Volatility 1/ DVPE 2/ D5191 7.20 Mercaptan Sulfur, wt % 3/ D3227 0.004 Hydrogen Sulfide D3227 None Copper Corrosion D130 1 Silver Corrosion D4814 1 Gum, Existent, mg/100ml D381 4 5



Lead, g/gal D3237 0.010 0.05

Research Octane {R} D2699 Report Motor Octane {M} D2700 80.0 (R+M)/2 8/ D4814 83.7 (R+M)/2 (After blending) D4814 87.0 Benzene, wt. % D3606 1.3 Aromatics (vol %) 4/ 50 Olefins (vol %) D1319 25 Sulfur, ppm D2622 80 Oxygen Content wt% 5/ D5599 1.5 4.0 Oxygenates, wt % 8/ D4815 0.33 E200 (vol%) D86 30 70 E300(vol%) D86 70 100 Emission Performance Reduction (%) 27.0 Haze rating 6/, 8/ D4176 2 3

NACE Corrosion TM0172 B+ Odor 7/, 8/ Nonoffensive


SPECIFICATIONS FOR NR GRADE GASOLINE BLENDSTOCK (RBOB)

Grade 21 1/ Refer to Seasonal Gasoline Volatility Schedule.

2/ For products blended to meet EPA or state imposed summer VOC requirements, test

must be performed for RVP in accordance with procedure described in 40 CFR, PART

80, Appendix E, Method 3.



4/ Refer to test methods in 40 CFR Chapter 1, Part 80.46.

5/ Oxygen content must meet a minimum of 1.5 wt. % and a maximum of 4.0 wt. % after

blending of denatured fuel ethanol.







8/ Specfications must be met before blending of denatured fuel ethanol

**NOTE: This RBOB may not be combined with any other RBOB except RBOB having

the same requirement for oxygenate type and amount. “Base Gasoline” Not for sale to the

ultimate consumer.

**NOTE: Heavy metals are not allowed to be present.

**NOTE: All parameters must be met after blending with denatured fuel ethanol unless noted.

Rev. 1

3/13/09


Central West


December 1, 2011

SPECIFICATIONS FOR PREMIUM REFORMULATED GASOLINE BLENDSTOCK

(RBOB)


ASTM Origin



Gravity, Degrees API D287 Report Only 1/

Color Undyed DVPE 2/ D5191

G3, 3G (Non-VOC controlled) 11.5 G4, 4G(Non-VOC controlled) 13.5 G5, 5G (Non-VOC controlled) 15.0 G1,1G,G2,2G (VOC controlled) Report 6/




Lead, g/gal D3237 0.010 0.05

Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 93.0 Sulfur, ppm 4/ D2622 80 Oxygen Content, wt % D5599 5/, 6/, 10/



E200, vol % D86 30 70 E300, vol % D86 70 100 Olefins, vol % D1319 25 Emissions Performance Reductions, % 11/

Region 1 (G1, 1G) -27 (-28 during cycles 14-21) -25

Region 2 (G2, 2G) -25.4 (-26.4 during cycles 14-21) -23.4

Odor 8/ Nonoffensive Volatility: Driveability Index D4814 See chart

Central West


December 1, 2011

SPECIFICATIONS FOR PREMIUM REFORMULATED GASOLINE BLENDSTOCK

(RBOB)



D2533, D5188



G1,G2 1250 158 170 250 374 430 133

G3 1230 140 170 240 365 430 124

G4 1220 131 150 235 365 430 116

G5 1200 122 150 230 365 430 105



2/ For products blended to meet EPA or state imposed summer VOC requirements, tests must be

performed in accordance with the procedures described in 40 CFR, Part 80.



4/ Refer to 40 CFR Part 80.195 (d)(2). Alternate sulfur test methods, ASTM D5453 and D7039,

may be used according to federal and state regulations.

5/ All E grades may not contain oxygenates, such as ethers and alcohols. The use of non-

hydrocarbon blending components is prohibited. Origin maximum MTBE 0.25 vol.%. Delivery

maximum 0.50 vol.%.

6/ Refer to test methods published in 40 CFR Chapter 1, Part 80.46. Alternate aromatics and

oxygenates test methods, ASTM D1319 and D4815, may be used according to federal and state

regulations.





8/ Any gasoline exhibiting an offensive odor and/or containing more than 0.50 wt % dicyclopentadiene will not be accepted for shipment.

9/ Computer, Linear and Nomogram methods may be used to determine V/L value. D2533 will be

the referee. 10/ Oxygen content must meet a minimum of 1.7 wt.% and a maximum of 4.0 wt.% after blending

with denatured fuel ethanol. 11/ Emissions reductions must be calculated using EPA guidelines.

Rev.1, 3/13/09

mailto:@20

Central West


ASTM Origin


Benzene, vol % D3606 1.30 Research Octane {R} D2699 Report Motor Octane {M} D2700 Report (R+M)/2 D4814 93.0 Oxygen Content, wt % D5599,GC-OFID(See Note) 1/2/7/8/

Aromatics, vol % D5769,D5599,GC-OFID(SeeNote) 50 2/ E200, vol % D86 30 70 E300, vol % D86 70 100 Olefins, vol % D1319 ,D6550 25 Sulfur, ppm D2622 80 9/

DVPE D5191 3/ 223, 322 (Non-VOC controlled) 11.5 224, 422 (Non-VOC controlled) 13.5 225, 522 (Non-VOC controlled) 15.0 221,122,222,222 (VOC controlled) Report 2/

Emissions Performance Reductions, % 4/

Region 1 (221, 122) -27 -25 Region 2 (222, 222) -25.4 -23.4

SPECIFICATIONS FOR PREMIUM REFORMULATED GASOLINE BLENDSTOCK (RBOB)

– GRADE 22

For Blending With 10% Denatured Fuel Ethanol (92% Purity) As Defined In ASTM D4806

This RBOB may not be combined with any other RBOB except RBOB having the same



All Grade 22 Requirements (Segregated and Fungible):

Central West



– GRADE 22

Fungible Only Requirements:

ASTM

Test

Origin

Shipments

Deliveries

Specification Points

Color

Method Minimum Maximum

Undyed

(At Terminals) Note

Copper Corrosion D130 1 Silver Corrosion D4814

Doctor test D4952 1

Negative(sweet)

5/

or

Mercaptan Sulfur, wt % D3227

0.002

Gum, Existent, mg/100ml D381

Gravity, Degrees API D287

Oxidation Stability, min. D525

240

4

Report Only

5

180

7/

Phosphorous, g/gal D3231 0.004 0.005 Lead, g/gal D3237

NACE Corrosion TM0172

B+

0.010 0.05 7/

Volatility:

Driveability Index D4814

See chart


Vapor/Liquid Ratio (V/L), F @20 D5188 See chart

See chart

6/



221,222 1250 158 170 250 374 430 133

223 1230 140 170 240 365 430 124

224 1220 131 150 235 365 430 116

225 1200 122 150 230 365 430 105

Heavy metals are not allowed to be present.


Any gasoline exhibiting an offensive odor and/or poses a personal health hazard will not be accepted for shi pment.

Any gasoline containing more than 0.50 wt. % of dicyclopentadiene will not be accepted for shipment.


Delivery results may vary by the smaller of ASTM reproducibility for a given test or any test tolerance as allowed by state or

EPA regulations at the point of delivery.

1/ All 21 grades may not contain oxygenates, such as ethers and alcohols. The use of non -hydrocarbon blending

components is prohibited. Origin maximum MTBE 0.25 vol. %. Delivery maximum 0.50 vol.%.

2/ Refer to test methods published in 40 CFR Chapter 1, Part 80.46. Alternate aromatics and oxygenates test methods,


mailto:@20

Central West



– GRADE 22


accordance with the procedures described in 40 CFR, Part 80. 4/ Emissions reductions must be calculated using EPA guidelines.

5/ Mercaptan Sulfur waived if fuel is negative by Doctor test.



8/ Oxygen content must meet a minimum of 1.7 wt. % and a maximum of 4.0 wt.% after blending with denatured fuel

ethanol.



Rev. 2

03/29/2011

SPECIFICATION FOR LIGHT NAPHTHA



Specification Points Methods Minimum Maximum May Be Specific Gravity D1298 0.680 0.850

Color D1500 5

Reid Vapor Pressure, psi D5191 12.5

Distillation, D86 IBP 60

Water and Sediment D1786 2.0

Product shall be clear and bright and free of suspended matter.

Rev. 1

11/01/10

Central West


Gasoline, Fuel Oil and Diesel Fuel Additive Specifications

(From origin or interconnecting pipeline.)

The following additive specifications apply to all grades except aviation

products, LPG’s, and Natural Gasoline.

Gasoline Additives

Gum Inhibitors and Metal Deactivators

Gasoline shipments may, but are not required to, contain any of the following gum

inhibitors and/or metal deactivators:

N, N’di-secondary butyl ortho-phenylenediamine

N, N’di-secondary butyl para-phenlyenediamine

N, N’disalicylidene-1, 2 propanediamine

N, N’di(1-ethyl-3-methylpentyl)-para-phenylenediamine

N, N’di-isopropyl-para-phenylenediamine

N,n’bis-(1, 4-demethylpentyl)-p-phenylenediamine n-butyl-para-aminophenol

2-6-di-tert-butylphenol

2, 4,6-tri-tert-butylphenol

Ortho-tert-butylphenol

UOP12P UOP12S UOP17P

UOP3455 UOP5S Octel AO-31

Octel AO-33 Octel AO-35 Octel AO-36

Ethyl 733 HiTech 4776 HiTech 4720

HiTech4740 Tolad 3905 Tolad 3910

Specaid 8Q202 Naco 88BU-118 IPC 4650

Pitt-Concol M-56 IPC 4695 Unichem 7529

IPC 4690

Corrosion Inhibitors - Products requiring compliance with NACE standard TM0172 may

contain any of the following corrosion inhibitors:

Nalco 5403 Welchem 91120 Nalco 5405

Welchem 91121 Nalco Visco 3554 Specaid8Q103

Apollo PRI-19 Lubrizol 541 Baypros 853

UOP Unicor Octel DCI-4A Unichem 7504

UOP UnicorPL Octel DCI-6A UOP Unicor J

Tolad 245 Hitec E-534 Tolad 249

Central West


Hitech 580 IPC 4410 Unichem 7501

Tolad 9719 Tolad 9715

Gasoline, Fuel Oil and Diesel Fuel Additive Specifications Fuel Oil and Diesel Fuel additives

Stability Fuel oil and/or diesel fuel shipments may contain one or more of

the following stability additives as required to achieve compliance

with the stability characteristics outlined in the applicable grade

specification.

Octel FOA-3 Chemtec 7220 Octel FOA-11

UOP Polyflo-121 Nalco 5303 Nalco 5301

UOP Polyflo-122 Tretolite Tolad 260 Specaid8Q401

UOP Polyflo-128 Petrolite T-9022 Specaid8Q403

UOP Polyflo-195 Unichem 7530 Specaid8Q72

Tolad 9076

Pour depressants Fuel oil and/or diesel fuel shipments requiring additives to achieve

compliance with low temperature properties may, but are not

required to, contain one or more of the following pour point

depressant additives:

Hitec 4518 Tolad 35 Hitec 4541

Tolad 345 Paradyne 25 Nalco 5375

Unichem 8094 Exxon ECA 7305 Tolad 3005

Octel PDD-7450 UOP Polyflo 6000 Betz 8Q12

Betz Specaid 8Q72 Specaid Dearborn 8Q30

Revision date: 2/23/11


Central West


SEASONAL GASOLINE VOLATILITY SCHEDULE

SHIPMENTS FROM MCKEE ORIGIN

Amarillo 8” Pipeline System

Premium Unleaded Gasoline

. Jan.

1-30

Feb.

1-28

Mar.

1-31

Apr.

1-30

May

1-31

June

1-30

July

1-31

Aug.

1-31

Sept.

1-15

Sept.

16-30

Oct.

1-31

Nov.

1-30

Dec.

1-31

Amarillo

13.50

8.50

8.50

9.00

9.00

9.00

9.00

9.00

9.00

10.00

11.50

13.50

13.50

D-4 A-3 A-2 A-2 A-2 A-1 A-1 A-1 A-1 B-2 C-3 D-4 D-4

Albuquerque

13.50

8.50

8.50

9.00

9.00

9.00

9.00

9.00

9.00

10.00

11.50

13.50

13.50

D-4 A-3 A-2 A-2 A-2 A-1 A-1 A-2 A-2 B-2 C-3 D-4 D-4

Abernathy

13.50

8.50

8.50

9.00

9.00

9.00

9.00

9.00

9.00

10.00

11.50

13.50

13.50

D-4 A-3 A-2 A-2 A-2 A-1 A-1 A-1 A-1 B-2 C-3 D-4 D-4

Rev.3, 03/30/2011

Central West




Amarillo 8” Pipeline System

Regular Unleaded Gasoline

. Jan.

1-30

Feb.

1-28

Mar.

1-31

Apr.

1-30

May

1-31

June

1-30

July

1-31

Aug.

1-31

Sept.

1-15

Sept.

16-30

Oct.

1-31

Nov.

1-30

Dec.

1-31

Amarillo

13.50

11.50

8.50

9.00

9.00

9.00

9.00

9.00

9.00

10.00

11.50

13.50

13.50

D-4 C-3 A-2 A-2 A-2 A-1 A-1 A-1 A-1 B-2 C-3 D-4 D-4

Albuquerque

13.50

11.50

8.50

9.00

9.00

9.00

9.00

9.00

9.00

10.00

11.50

13.50

13.50

D-4 C-3 A-2 A-2 A-2 A-1 A-1 A-2 A-2 B-2 C-3 D-4 D-4

Abernathy

13.50

11.50

8.50

9.00

9.00

9.00

9.00

9.00

9.00

10.00

11.50

13.50

13.50

D-4 C-3 A-2 A-2 A-2 A-1 A-1 A-1 A-1 B-2 C-3 D-4 D-4

Rev.3, 03/30/2011

Central West




Colorado Springs Pipeline System


. Jan. Feb. Mar. Apr. May June July Aug. Sept. Sept. Oct. Nov. Dec.

1-30 1-28 1-31 1-30 1-31 1-30 1-31 1-31 1-15 16-30 1-31 1-30 1-31

Colorado Springs

15.00

8.50

8.50

8.50

9.00

9.00

9.00

9.00

9.00

10.00

11.50

13.50

15.00

D-5 A-4 A-4 A-3 A-3 A-2 A-2 A-2 A-2 B-2 C-3 D-4 E-5

Rev 2, 1/14/09

Central West




Colorado Springs Pipeline System



1-30 1-28 1-31 1-30 1-31 1-30 1-31 1-31 1-15 16-30 1-31 1-30 1-31

Colorado Springs

15.00

13.50

8.50

8.50

9.00

9.00

9.00

9.00

9.00

10.00

11.50

13.50

15.00

D-5 D-4 A-4 A-3 A-3 A-2 A-2 A-2 A-2 B-2 C-3 D-4 E-5

Rev 2, 1/14/09

Central West




El Paso Pipeline System


. Jan.

1-30

Feb.

1-28

Mar.

1-31

Apr.

1-30

May

1-31

June

1-30

July

1-31

Aug.

1-31

Sept.

1-15

Sept.

16-30

Oct.

1-31

Nov.

1-30

Dec.

1-31

El Paso - Local

13.50

7.00

7.00

7.00

7.00

7.00

7.00

7.00

7.00

10.00

11.50

13.50

13.50

D-4 A-4 A-2 A-2 A-1 A-1 A-1 A-1 A-1 B-2 C-3 D-4 D-4

El Paso – Tucson

13.50

9.00

9.00

9.00

9.00

9.00

9.00

9.00

9.00

10.00

11.50

13.50

13.50

D-4 A-3 A-2 A-2 A-2 A-2 A-1 A-1 A-1 B-2 C-3 D-4 D-4

El Paso – Phoenix

8.00

7.00

7.00

7.00

7.00

7.00

7.00

7.00

7.00

7.00

8.00

8.00

8.00

A-2 A-2 A-2 A-2 A-1 A-1 A-1 A-1 A-1 A-1 A-2 A-2 A-2

Rev 3, 03/30/2011

Central West




El Paso Pipeline System


. Jan.

1-30

Feb.

1-28

Mar.

1-31

Apr.

1-30

May

1-31

June

1-30

July

1-31

Aug.

1-31

Sept.

1-15

Sept.

16-30

Oct.

1-31

Nov.

1-30

Dec.

1-31

El Paso - Local

13.50

11.50

7.00

7.00

7.00

7.00

7.00

7.00

7.00

10.00

11.50

13.50

13.50

D-4 C-4 A-2 A-2 A-2 A-1 A-1 A-1 A-1 B-2 C-3 D-4 D-4

El Paso – Tucson

13.50

9.00

9.00

9.00

9.00

9.00

9.00

9.00

9.00

10.00

11.50

13.50

13.50

D-4 A-3 A-2 A-2 A-2 A-2 A-1 A-1 A-1 B-2 C-3 D-4 D-4

El Paso – Phoenix

8.00

8.00

7.00

7.00

7.00

7.00

7.00

7.00

7.00

7.00

8.00

8.00

8.00

A-2 A-2 A-2 A-2 A-1 A-1 A-1 A-1 A-1 A-1 A-2 A-2 A-2

Rev 3, 03/30/2011

Central West



1-30 1-28 1-31 1-30 1-31 1-30 1-31 1-31 1-15 16-30 1-31 1-30 1-31

13.50

11.50

10.00

8.50

8.80

8.80

8.80

8.80

8.80

10.00

11.50

13.50

13.50

D-4 C-3 B-2 A-2 A-2 A-1 A-1 A-1 A-1 B-2 C-3 D-4 D-4


SHIPMENTS FROM THREE RIVERS ORIGIN

Laredo Pipeline System


Laredo

Rev 3, 03/30/2011

Central West



1-30 1-28 1-31 1-30 1-31 1-30 1-31 1-31 1-15 16-30 1-31 1-30 1-31

13.50

11.50

10.00

8.50

8.80

8.80

8.80

8.80

8.80

10.00

11.50

13.50

13.50

D-4 C-3 B-2 A-2 A-2 A-1 A-1 A-1 A-1 B-2 C-3 D-4 D-4



Laredo Pipeline System


Laredo

Rev 3, 03/30/2011

Central West




San Antonio East Pipeline System



1-30 1-28 1-31 1-30 1-31 1-30 1-31 1-31 1-15 16-30 1-31 1-30 1-31

San Antonio East

13.50

11.50

10.00

7.50

6.80

6.80

6.80

6.80

6.80

10.00

11.50

13.50

13.50

D-4 C-3 B-2 A-2 A-2 A-1 A-1 A-1 A-1 B-2 C-3 D-4 D-4

Rev 3, 8/09/10

Central West




San Antonio East Pipeline System



1-30 1-28 1-31 1-30 1-31 1-30 1-31 1-31 1-15 16-30 1-31 1-30 1-31

San Antonio East

13.50

11.50

10.00

7.50

6.80

6.80

6.80

6.80

6.80

6.80

11.50

13.50

13.50

D-4 C-3 B-2 A-2 A-2 A-1 A-1 A-1 A-1 B-2 C-3 D-4 D-4

Rev 3, 03/30/2011

Central West




San Antonio South Pipeline System



1-30 1-28 1-31 1-30 1-31 1-30 1-31 1-31 1-15 16-30 1-31 1-30 1-31

San Antonio South

13.50

11.50

10.00

6.50

6.80

6.80

6.80

6.80

6.80

6.80

11.50

13.50

13.50

D-4 C-3 B-2 A-2 A-2 A-1 A-1 A-1 A-1 B-2 C-3 D-4 D-4

Rev 3, 03/30/2011

V - Seasonal Gasoline Volatility Classes

Shipments from Origin

Reid Vapor Pressure, D5191 1/

Distillation - ASTM D86

March 1 - September 15

September 16 - February 28

Class

DVPE using EPA formula 2/

DVPE

AA A B C D E

10% Evaporated F max

158

158

149

140

131

122

50% Evaporated F min

170

170

170

170

170

170


250

250

245

240

235

230


374

374

374

365

365

365

Final Boiling Point F, max 3/

430

430

430

430

430

430

Residue, vol % max

2

2

2

2

2

2

Driveability Index, max

ASTM D4814

1250

1250

1240

1230

1220

1200

Vapor/Liquid Ratio = 20:1

Class 1

2

3

4

5

F Min. 4/ 140 133 124 116 105

1/ The RVP of all gasoline deliveries will not exceed applicable Federal, State, or ASTM

D4814, Table 2 maximums.

2/ The calculation required for the EPA compliance period is published in 40 CFR 80.46.

3/ The final boiling point of all gasoline deliveries at terminals will be at or below 437 F as

determined by ASTM D-86

4/ Although ASTM D2533 is the referee test method, D5188 or the equations in D4814 may

also be used. Rev. 1

3/13/09


Central West



SHIPMENTS FROM CORPUS CHRISTI ORIGIN

Valley Pipeline System



1-30 1-28 1-31 1-30 1-31 1-30 1-31 1-31 1-15 16-30 1-31 1-30 1-31

Edinburg

13.50

13.50

11.50

8.50

9.00

9.00

9.00

9.00

9.00

9.00

11.50

13.50

13.50

D-4 D-4 C-3 A-3 A-3 A-3 A-2 A-2 A-2 A-2 C-3 D-4 D-4

Rev 3, 03/30/2011

nustar logistics, l.p....nustar logistics, l.p. product specifications central west i september15,...

Documents