nox e devicelist long

7/28/2019 NOX E Devicelist Long

1/22

NOX EMA, December 04, p 1 of 22 NOX E Devicelist long.doc

NOX Systemprice listterms and conditions:All prices in CHF without VAT and taxes. Prices, availability and specifications

subject to change all prices FOB shipping point Vaduz, Liechtenstein.

distributed bySauter Electronic AGAlvierweg 179490 VaduzFrstentum Liechtenstein

Telefon +423 237 57 37Fax +423 232 03 36

e-mail [email protected]


2/22


table of content

central unit .......................................................................................3power supply unit ..............................................................................4control panel .....................................................................................5touch screen .....................................................................................6code entry unit ..................................................................................7multi I/O device.................................................................................8input device ......................................................................................9mini device......................................................................................10relay device.....................................................................................11radio controlled clock device............................................................. 12card reader device ...........................................................................13printer interface device ....................................................................14repeater / converter.........................................................................15

S8 Interface ....................................................................................16temperature and humidity sensor......................................................17housing for CPU/PSU .......................................................................18power supply board .........................................................................19radio receiver module ...................................................................... 20battery powered receiver.................................................................. 21picture monitoring unit.....................................................................22


3/22


central unit

CPU, central unit part no. N101

All devices contain an intelligent communication addressed directly to the central unit. Thecentral unit controls the alarm system, and handles the multiple communication to theoutside world. It further secures the proper handling of the user and database.

housing: stainless, with sabotage detectiondimension: W 650mm, H 400mm, D 90mm

consisting of:

CPU board with 32MB flash memory and Ethernet connector BUS board with 3 x RS 485 NOX alarm bus PSU unit, 3A (accus, 2x17Ah, not included) MIO card with 8 relays and four monitored siren and flash output Built into steel casing, PSU, all other listed devices and space for an optional alarm

transmission unit, sabotage contact

TPS/SVV certified for category 3 (Switzerland)


4/22


power supply unit

PSU, power supply unit part no. N103

Uninterruptible power supply with accumulator backup. This unit provides interruption freeDC supply to the NOX alarm bus, it also monitors AC failure, AC high/low, accu failure, overtemperature and the actual output power. The unit comes with a housing holding the PSU,accus and depending on configuration, interface and relay devices


consisting of:

transformer 230V/50Hz (115V/60Hz available on request) regulator board with onboard check system 3A maximum output power mains plug with filter housing stainless, with sabotage detection tray for two accus with 2x17Ah (up to 30hours backup power)


5/22


control panel

CPA, control panel part no. N110

The control panel is used to operate the alarm system. It has a numeric keypad and a whitelight graphic display with 128 x 64 pixel

housing: Aluminium, with sabotage detectiondimensions: AP L 175mm, W 110mm, H 23mm

UP L 212mm, W 148mm, H 23mm

consisting of:

housing Aluminium, with sabotage detection foil, grey and graphic display with 128 x 64 pixels controller board with alarm bus terminal


6/22


touch screen

TPA, 10.4 touch panel Art. Nr. N111

The touch screen with 10.4 inch screen diagonal allows to operate the NOX security systemby finger touch directly on graphic floor plans in color.

housing: plastic

dimensions: L 312mm, H 242mm

consisting of:

10.4 display i plastic housing resistive Touch Screen Ethernet interface for fast connection to NOX CPU


7/22


code entry unit

KPD, code entry unit on wall part no. N113AP

in wall part no. N113UP

The code entry unit is a numeric keypad with indicators. It is typically used to arm/disarmdifferent areas or it can alternatively be used to trigger an electrical door opener.

variant on wall variant in wall

housing: Aluminium, with sabotage detectiondimension: L 100mm, W 70mm, H 23mm

consisting of:

housing Aluminium, with sabotage detection foil, grey two LED (green/red) for status display board with NOX alarm bus terminal


8/22


multi I/O device

MIO, multiple input/output unit part no. N105

This external MIO unit, not installed inside central housing is used to connect flash lightsand/or a siren. Special feature of the MIO are four monitored outputs used to connectacoustic or optic indicators (e.g. siren or flash lights). These monitored outputs canalternatively be used as standard resistance monitored inputs. Another additional eight relayoutputs are available on the MIO board.maximum relay switching power: 30V/1A

features:

8 relay outputs4 monitored outputs OR4 resistance inputs / 4 open collector outputs

consisting of:

housing plastic, white with sabotage detection controller board with NOX alarm bus terminal


9/22


input device

IN4, input unit part no. N120

The IN4 is a universal input device with four resistance-monitored inputs for connection tothe NOX alarm bus. It connects alarm units and detectors with the system.A unique feature of this unit is the programmable input resistance level. It is possible toadjust the resistance surveillance level between 3 to 40k inn order to enable connection ofa wide range of all types detectors and sensors.Additionally every input has a programmable delay time to adjust the alarm trigger to anyspecific requirement.

housing: plastic, white, with sabotage detectiondimensions: L 85mm, W 66mm, H 27mm

consisting of:

housing plastic, with sabotage detection intelligent board with NOX alarm bus terminal


10/22


mini device

m31, mini i/o module part no. N121

The M31 is a very small and compact module with an open collector output and 3 inputs.This module is designed to be integrated into the detector. The inputs are not resistantsupervised.

dimensions: L 16mm, W 23mm, H 10mm


11/22


relay device

RE4, relay output unit part no. N122

RE4 is a universal output device with four freely programmable relay outputs. The device isconnected and supplied through the NOX alarm bus. No additional supply is needed.maximum relay switching power: 30V/1A


consisting of:

housing plastic, with sabotage detection relay board with NOX alarm bus terminal


12/22


radio controlled clock device

DCF, radio clock device part no. N130

To assure an accurate time for all alarm loggings a radio controlled clock interface can beconnected to the alarm bus. A DCF-77 receiver unit is connected to the DCF interface. TheDCF-77 signal is aired out of Frankfurt (D) throughout countries in Europe.


consisting of:

housing plastic, with sabotage detection interface board with NOX alarm bus terminal

+


13/22


card reader device

CRx, card reader device

CRD is a universal input/output device connected to the NOX alarm bus with Wiegand 26Bit interface. The CRD includes one resistance monitored input, one relay output and a cardreader port.With the PRD it is possible to integrate the commonly used card systems (e.g. Legic, Temic,Mifare, Hitag) with the NOX alarm system.


consisting of:

housing plastic, with sabotage detection board with NOX alarm bus terminal two LED outputs for status displayversions:N115 CRD card reader interface with 26bit WiegandN116 CRA card reader interface with Data/Clock interface Omron protocolN118 CRB card reader interface with 40bit WiegandN119 CRC card reader interface with 27bit and 40bit Wiegand for HID iCLASS


14/22


printer interface device

PRT, printer interface device part no. N131

Serial printer interface to connect peripheral RS-232 serial printer devices to the NOX alarmbus.


consisting of:

housing plastic, with sabotage detection board with NOX alarm bus terminal


15/22


repeater / converter

RPT, repeater / converter device part no. N141

Universal bus repeater (RS485) or serial interface (RS232), configurable by on board jumper.It allows to extend a bus wire length beyond the standard length and/or gives the possibilityto separate the NOX alarm bus of specified sensor groups from others.


consisting of:

housing plastic, with sabotage detection board with NOX alarm bus terminalno external connector (NOXRPT)


16/22


S8 Interface

IS8, S8 interface device part no. N142

The IS8 Interface is used to connect bus unit from the SAEL S8 intruder detection system tothe NOX alarm bus. The interface exists of two parts; a NOX converter and an S8 interfaceboard.

two housings: plastic, white, with sabotage protectiondimensions: each housing L 85mm, W 66mm, H 27mm

consisting of:

2 housings plastic, with sabotage protection controller card with NOX bus terminal S8 interface card


17/22


temperature and humidity sensor

THS, temperature & humidity sensor internal Art. Nr. N150I

external Art. Nr. N150E

The NOX THS measures temperature and humidity. The sensor is available in two versionsfor internal and external use. The measured values are forwarded through the NOX bus tothe central. The software allows to specify two upper and two lower threshold values foreach value, to trigger a warning and an alarm. These messages can then be used in thecustomer program to trigger various actions.In addition all measured values are stored for up to one year. The trend of temperature andhumidity can is displayed as a graphic on a PC by the NOX software. Three different graphsshow the trend for one day, for one month and another graph shows an entire year.

housing: plastic, whitedimensions: L 105mm, W 58mm, H 18.5mmweight: 80g

consisting of:(internal sensor)

housing intelligent board with integrated, combined sensor for temperature and humidity(external Sensor) combined temperature and humidity sensor fitted in a metal tube with 5m cable housing intelligent board


18/22


housing for CPU/PSU

housing part no. N106

Central unit housing can be supplied also separately.


consisting of:

housing stainless, white with sabotage detection tray for two accus with max. 2x17Ah tray for additional devices


19/22


power supply board

PSU board, power supply part no. N107

Switched power supply unit. This unit provides interruption free DC supply to the NOX bus, italso monitors AC failure, AC high/low, accu failure, over temperature and the actual outputpower.

dimension: W 340mm, H 100mm, D 80mm

consisting of:

transformer 230V/50Hz (115V/60Hz available on request) regulator board with onboard check system 3A maximum output power mains plug with filter


20/22


radio receiver module

RXM, radio receiver module part no. P110

Receiver module for 860MHz picture monitoring transmitter signals. The module is connectedby a four wire cable to the NOX alarm bus. No other wires needed the unit is suppliedthrough the bus cable. The unit is monitored against sabotage by the central unit.


consisting of:

housing plastic, with sabotage detection intelligent board with NOX alarm bus terminal


21/22


battery powered receiver

BPR, mobile alarm receiver part no. P102

Portable , battery powered alarm receiver module for 860MHz picture monitoring transmittersignals. The compact module has a red alarm and battery low LED, a flashing in operationgreen LED and an on/off switch. The alarm signalisation is done by a built in beeper.

housing: plastic, white, with belt clipdimensions: L 120mm, W 66mm, H 27mm

consisting of:

housing plastic, with belt clip intelligent board with red and green status LED and an integrated alarm beeper


22/22

picture monitoring unit

TXM, radio- picture monitoring module part no. P111

The PMGS radio monitoring unit detects every soft movement or position shift of an objects.The sensitivity is adjustable in 8 steps through a simple micro switch. The unit does notcontain Mercury or other toxic materials.It is CE certified and it does not interfere with other radio equipments.

figure shows real size!

housing: plastic, whitedimensions: L 105mm, W 58mm, H 18.5mmweight: 80g

consisting of:

housing intelligent board and integrated antenna two 1.5V batteries AAA type

nox e devicelist long

Documents