notice of exempt modification – facility modification 19
TRANSCRIPT
22816305-v1
September 24, 2021 Via Electronic Mail Melanie A. Bachman, Esq. Executive Director/Staff Attorney Connecticut Siting Council 10 Franklin Square New Britain, CT 06051 Re: Notice of Exempt Modification – Facility Modification
19 Main Street, Old Saybrook, Connecticut Dear Attorney Bachman:
Cellco Partnership d/b/a Verizon Wireless (“Cellco”) currently maintains an existing wireless telecommunications facility at the above-referenced property address (the “Property”). The facility consists of antennas and remote radio heads attached to roof-top masts within a radio frequency transparent enclosure and related equipment on the roof. The roof-top facility was approved by the Siting Council (“Council”) in June 2015 (Petition No. 1155). A copy of the Council’s Petition No 1155 Decision and Staff Report is included in Attachment 1.
Cellco now intends to modify its facility by replacing six (6) existing antennas with three (3) Samsung MT6407-77A antennas and three (3) MX06FIT465-02 antennas on its existing masts. Cellco also intends to replace six (6) existing remote radio heads (“RRHs”) with six (6) new RRHs behind the roof-top parapet. A set of project plans showing Cellco’s proposed facility modifications and new antennas and RRH specifications are included in Attachment 2.
Please accept this letter as notification pursuant to R.C.S.A. § 16-50j-73, for construction that constitutes an exempt modification pursuant to R.C.S.A. § 16-50j-72(b)(2). In accordance with R.C.S.A. § 16-50j-73, a copy of this letter is being sent to Old Saybrook’s Chief Elected Official and Land Use Officer.
KENNETH C. BALDWIN 280 Trumbull Street Hartford, CT 06103-3597 Main (860) 275-8200 Fax (860) 275-8299 [email protected] Direct (860) 275-8345 Also admitted in Massachusetts and New York
Melanie A. Bachman, Esq. September 24, 2021 Page 2
The planned modifications to the facility fall squarely within those activities explicitly provided for in R.C.S.A. § 16-50j-72(b)(2).
1. The proposed modifications will not result in an increase in the height of the existing tower.
2. The proposed modifications will not involve any change to ground-mounted equipment and, therefore, will not require the extension of the site boundary.
3. The proposed modifications will not increase noise levels at the facility by six decibels or more, or to levels that exceed state and local criteria.
4. The installation of Cellco’s new antennas will not increase radio frequency (RF) emissions at the facility to a level at or above the Federal Communications Commission (FCC) safety standard. Far Field approximation tables for Cellco’s modified facility are included in Attachment 3. The modified facility will be capable of providing Cellco’s 5G wireless service.
5. The proposed modifications will not cause a change or alteration in the physical or environmental characteristics of the site.
6. According to the attached Structural Letter, including review of existing mounting structure (“SL”), the host building and antenna screening frame structure can support Cellco’s proposed modifications. A copy of the SL is included in Attachment 4.
A copy of the parcel map and Property owner information is included in Attachment 5. A Certificate of Mailing verifying that this filing was sent to municipal officials and the property owner is included in Attachment 6.
For the foregoing reasons, Cellco respectfully submits that the proposed modifications to the above-referenced telecommunications facility constitutes an exempt modification under R.C.S.A. § 16-50j-72(b)(2).
Melanie A. Bachman, Esq. September 24, 2021 Page 3
Sincerely,
Kenneth C. Baldwin
Enclosures Copy to:
Carl P. Fortuna, Jr., First Selectman for the Town of Old Saybrook Christina Costa, Old Saybrook Town Planner 231ST SRS LLC, Property Owner Alex Tyurin
ATTACHMENT 1
ATTACHMENT 2
Homepage
samsungnetworks.com
Youtube
www.youtube.com/samsung5g
Samsung’s future proof dual-band radio is designed to help effectively increase the coverage areas in wireless networks. This 700/850MHz 4T4R dual-band radio has 4Tx/4Rx to 2Tx/2Rx RF chains options and a total output power of 320W, making it ideal for macro sites.
Model Code RF4440d-13A
57196
57196
Homepage
samsungnetworks.com
Youtube
www.youtube.com/samsung5g
Samsung’s future proof dual-band radio is designed to help effectively increase the coverage areas in wireless networks. This AWS/PCS 4T4R dual-band radio has 4Tx/4Rx to 2Tx/2Rx RF chains options and a total output power of 320W, making it ideal for macro sites.
Model Code RF4439d-25A
57196
- -
14.96 x 14.96 x 10.04inch (36.8L) /74.7lb
57196
MT6407-77A
for High Capacity and Wide Coverage
Beamforming & MU-MIMO
Flexible-Use Licences
3.7 GHz 3.8 GHz 3.8 GHz 4.23.98 GHz 4.0 GHz
A1 A2 A3 A4 A5 B1 B2 B3 B4 C1 C2 C3 C4
Gua
rd B
and
FSSB5
Post-Transition FSS
20 megahertzsub-blocks
50.9L 79.4lbs
MAC/PLC
High-PHY
Low-PHY
RF
PDCP
MX06FIT465-02NWAV™ X-Pol Hex-Port Antenna
X-Pol, Hex-Port 4 ft, 65° macro FIT (Form in Tighter):
2 ports 698-894 MHz and 4 ports 1695-2180 MHz
l Excellent passive intermodulation (PIM) performance reduces harmful interference.
l Fully integrated (iRETs) with independent RET control for low and high bands forease of network optimization
l SON-Ready array spacing supports beamforming capabilities
l Suitable for LTE/CDMA/PCS/UMTS/GSMair interface technologies
l Integrated Smart Bias-Ts reduce leasing costs
l Optimized width for reduced wind loading
Electrical specification (minimum/maximum) Ports 1, 2 Ports 3, 4, 5, 6
Frequency bands, MHz 698-798 824-894 1695-1880 1850-1990 1920-2180
Polarization ± 45° ± 45°
Average gain over all tilts, dBi 13.4 13.5 16.4 16.8 17.2
Horizontal beamwidth (HBW), degrees 66.0 60.0 63.0 60.0 57.0
Front-to-back ratio, co-polar power @180°± 30°, dB >21 >21 >26.0 >25.0 >25.0
X-Pol discrimination (CPR) at boresight, dB >15.4 >14 >23 >22 >20
Sector power ratio, percent <5.5 <3.0 <5.1 <3.8 <3.6
Vertical beamwidth (VBW), degrees1 17.5 16.0 8.0 7.4 7.1
Electrical downtilt (EDT) range, degrees 2-16 2-16 0-9
First upper side lobe (USLS) suppression, dB1 ≤-15 ≤-16 ≤-18 ≤-18 ≤-18
Cross-polar isolation, port-to-port, dB1 25 25 25 25 25
Max VSWR / return loss, dB 1.5:1 / -14.0 1.5:1 / -14.0
Max passive intermodulation (PIM), 2x20W carrier, dBc -153 -153
Max input power per any port, watts 300 250
Total composite power all ports, watts 1500
1 Typical value over frequencyand tilt
©2019 JMAWireless. All rights reserved. This document contains proprietary information. All products, companynames, brands,and logosare trademarks™ or registered® trademarksof their respective holders. All specificationsare subject to change withoutnotice. +1 315.431.7100 [email protected]
02/22/19
Page1
Mechanical specifications
Dimensions height/width/depth, inches (mm) 52.5/ 12.2/ 10.7 (1331/ 310/ 273)
Shipping dimensions length/width/height, inches (mm) 62/ 20/ 15 (1625/ 508/ 381)
No. of RF input ports, connector type, and location 6 x 4.3-10 female, bottom
RF connector torque 96 lbf·in (10.85 N·m or 8 lbf·ft)
Net antenna weight, lb (kg) 38 (17.27)
Shipping weight, lb (kg) 76 (34.55)
Antenna mounting and downtilt kit included with antenna 91900318
Net weight of the mounting and downtilt kit, lb (kg) 18 (8.18)
Range of mechanical up/down tilt -2° to 12°
Rated wind survival speed, mph (km/h) 150 (241)
Frontal, lateral, and rear wind loading@ 150 km/h, lbf (N) 64 (283), 50 (222), 81 (360)
Equivalent flat plate @ 100 mph and Cd=2, sq ft 0.95
Front view Back view Bottom view
Ordering information
Antenna model Description
MX06FIT465-02 4F X-Pol HEX FIT 65°, 2-16° / 0-9° RET, 4.3-10 & SBT
Optional accessories
AISG cables M/F cables for AISG connections
PCU-1000 RET controller Stand-alone controller for RET control and configurations
©2019 JMAWireless. All rights reserved. This document contains proprietary information. All products, companynames, brands,and logosare trademarks™ or registered® trademarksof their respective holders. All specificationsare subject to change withoutnotice. +1 315.431.7100 [email protected]
02/22/19
Page 2
MX06FIT465-02NWAV™ X-Pol Hex-Port Antenna
Remote electrical tilt (RET 1000) information
RET location Integrated into antenna
RET interface connector type 8-pin AISG connector per IEC 60130-9
RET connector torque Min 0.5 N·m to max 1.0 N·m (hand pressure & finger tight)
RET interface connector quantity 2 pairs of AISGmale/female connectors
RET interface connector location Bottom of the antenna
Total no. of internal RETs (low bands) 1
Total no. of internal RETs (high bands) 1
RET input operating voltage, vdc 10-30
RETmax power consumption, idle state, W ≤ 2.0
RETmax power consumption, normal operating conditions, W ≤ 13.0
RET communication protocol AISG 2.0 / 3GPP
RET and RF connector topology
Each RET device can be controlled either via the designated external AISG connector or RF port as shown below:
RET device Band RF port
R1 698-894 1-2
RET device Band RF port
B1/B2 1695-2180 3-6
Array topology
3 sets of radiating arrays
R1: 698-894 MHzB1: 1695-2180 MHzB2: 1695-2180 MHz
Band RF port
1695-2180 3-4
698-894 1-2
1695-2180 5-6
©2019 JMAWireless. All rights reserved. This document contains proprietary information. All products, companynames, brands,and logosare trademarks™ or registered® trademarksof their respective holders. All specificationsare subject to change withoutnotice. +1 315.431.7100 [email protected]
02/22/19
Page 3
MX06FIT465-02NWAV™ X-Pol Hex-Port Antenna
ATTACHMENT 3
Far Field Approximation
with downtilt variation
Location: Old Saybrook Center CT
Site #: 2-0523
Date: 09/22/21
Name: Stephen Nerkowski
File Name: Old Saybrook Center CT - FF Power
Antenna Type: MX14FIT456-01
Operating Freq. (MHz): 751
Antenna Height (ft): 29.7
Antenna Gain (dBi): 11.1
Downtilt (degrees): 2.0
Feedline Loss (dB): 0.0
Tx Power (W): 40.0
No. of Channels: 4
Calc Angle 90.0 82.0 72.0 67.0 62.0 57.0 52.0 47.0 42.0 37.0 32.0 27.0 22.0 17.0 12.0 7.0 6.0 4.0
Solve for r, dx to antenna 26.7 27.0 28.1 29.0 30.3 31.9 33.9 36.5 39.9 44.4 50.4 58.9 71.3 91.4 128.5 219.3 255.7 383.1
Distance from Antenna Structure Base in Horizontal plane 0.0 3.8 8.7 11.4 14.2 17.4 20.9 24.9 29.7 35.5 42.8 52.5 66.1 87.4 125.7 217.6 254.3 382.2
Angle from Main Beam (reference to horizontal plane) 90.0 80.0 70.0 65.0 60.0 55.0 50.0 45.0 40.0 35.0 30.0 25.0 20.0 15.0 10.0 5.0 4.0 2.0
dB down from centerline (referenced to centerline) 29.7 29.2 30.6 33.4 34.9 29.4 25.4 24.4 27.6 26.9 20.2 20.1 31.7 11.4 4.5 1.1 0.7 0.2
Reflection Coefficient (1 to 4, 2.56 typical) 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56
Power Density (mW/cm^2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.01 0.01 0.01 0.00
Percent of Occupational Standard 0.03 0.03 0.02 0.01 0.01 0.02 0.05 0.05 0.02 0.02 0.07 0.05 0.00 0.16 0.39 0.29 0.24 0.12
Percent of General Population Standard 0.14 0.15 0.10 0.05 0.03 0.10 0.23 0.25 0.10 0.09 0.34 0.25 0.01 0.78 1.94 1.46 1.18 0.59
Max%: 1.94%
Instructions:
6) Spreadsheet calculates actual power density, then relates as Occupational or General Population percentage of FCC Standard.
7) An odd distance may be entered in the rightmost column of the lower table.
Estimated Radiated Emission
Single Emitter Far Field Model
Dipole/Wire/Yagi Antenna Types
1) Fill in Site Location, Site number, Date, Name of Person Responsible for Date, and enter File Name to ba saved as.
2) References to J4 refer to a point where the transmission line exits the equipment shelter and proceeds to the antenna(s). There is typically a connector located here where power measurements are made.
3) Enter Antenna Height (in feet to bottom of antenna), Antenna Gain (expressed as dBi, add 2.17 to dBd to obtain dBi), Antenna Size (vertical size in inches), Downtilt (in Degrees, enter zero if none),
Feedline loss from J4 to Antenna, and J4 Power (in watts).
4) From manufacturer's plots, or data sheet, input Angle from mainbeam and dB below mainbeam centerline.
5) Enter Reflection coefficient (2.56 would be typical, 1 for free space)
0.00
0.00
0.00
0.01
0.01
0.01
0.01
0.0
0.5
1.0
1.5
2.0
2.5
0.0 3.8 8.7 11.4 14.2 17.4 20.9 24.9 29.7 35.5 42.8 52.5 66.1 87.4 125.7 217.6 254.3 382.2
Po
we
r D
en
sity
mW
/cm
^2
Pe
rce
nt
of
FC
C S
tan
dard
Distance from Tower Base in the Vertical Plane (feet)Assumes level ground, normal to antenna mounting structure
Far Field ApproximationReference to Main Beam Centerline
% Occupational % General Public Power Density
700 MHz
Far Field Approximation
with downtilt variation
Location: Old Saybrook Center CT
Site #: 2-0523
Date: 09/22/21
Name: Stephen Nerkowski
File Name: Old Saybrook Center CT - FF Power
Antenna Type: MX14FIT456-01
Operating Freq. (MHz): 874
Antenna Height (ft): 29.7
Antenna Gain (dBi): 11.6
Downtilt (degrees): 2.0
Feedline Loss (dB): 0.0
Tx Power (W): 40.0
No. of Channels: 4
Calc Angle 90.0 82.0 72.0 67.0 62.0 57.0 52.0 47.0 42.0 37.0 32.0 27.0 22.0 17.0 12.0 7.0 6.0 4.0
Solve for r, dx to antenna 26.7 27.0 28.1 29.0 30.3 31.9 33.9 36.5 39.9 44.4 50.4 58.9 71.3 91.4 128.5 219.3 255.7 383.1
Distance from Antenna Structure Base in Horizontal plane 0.0 3.8 8.7 11.4 14.2 17.4 20.9 24.9 29.7 35.5 42.8 52.5 66.1 87.4 125.7 217.6 254.3 382.2
Angle from Main Beam (reference to horizontal plane) 90.0 80.0 70.0 65.0 60.0 55.0 50.0 45.0 40.0 35.0 30.0 25.0 20.0 15.0 10.0 5.0 4.0 2.0
dB down from centerline (referenced to centerline) 29.1 26.4 23.3 22.2 22.1 23.5 28.4 38.3 30.2 35.4 28.1 20.9 25.9 16 6 1.4 0.9 0.2
Reflection Coefficient (1 to 4, 2.56 typical) 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56
Power Density (mW/cm^2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.01 0.01 0.01 0.00
Percent of Occupational Standard 0.03 0.05 0.10 0.12 0.12 0.08 0.02 0.00 0.01 0.00 0.01 0.04 0.01 0.05 0.26 0.26 0.22 0.11
Percent of General Population Standard 0.15 0.27 0.52 0.62 0.59 0.38 0.11 0.01 0.05 0.01 0.05 0.20 0.04 0.26 1.32 1.31 1.08 0.57
Max%: 1.32%
Instructions:
6) Spreadsheet calculates actual power density, then relates as Occupational or General Population percentage of FCC Standard.
7) An odd distance may be entered in the rightmost column of the lower table.
Estimated Radiated Emission
Single Emitter Far Field Model
Dipole/Wire/Yagi Antenna Types
1) Fill in Site Location, Site number, Date, Name of Person Responsible for Date, and enter File Name to ba saved as.
2) References to J4 refer to a point where the transmission line exits the equipment shelter and proceeds to the antenna(s). There is typically a connector located here where power measurements are made.
3) Enter Antenna Height (in feet to bottom of antenna), Antenna Gain (expressed as dBi, add 2.17 to dBd to obtain dBi), Antenna Size (vertical size in inches), Downtilt (in Degrees, enter zero if none),
Feedline loss from J4 to Antenna, and J4 Power (in watts).
4) From manufacturer's plots, or data sheet, input Angle from mainbeam and dB below mainbeam centerline.
5) Enter Reflection coefficient (2.56 would be typical, 1 for free space)
0.00
0.00
0.00
0.00
0.00
0.01
0.01
0.01
0.01
0.01
0.0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
0.0 3.8 8.7 11.4 14.2 17.4 20.9 24.9 29.7 35.5 42.8 52.5 66.1 87.4 125.7 217.6 254.3 382.2
Pow
er
Densi
ty m
W/c
m^2
Pe
rcent
of
FC
C S
tandard
Distance from Tower Base in the Vertical Plane (feet)Assumes level ground, normal to antenna mounting structure
Far Field ApproximationReference to Main Beam Centerline
% Occupational % General Public Power Density
850 MHz (Cellular)
Far Field Approximation
with downtilt variation
Location: Old Saybrook Center CT
Site #: 2-0523
Date: 09/22/21
Name: Stephen Nerkowski
File Name: Old Saybrook Center CT - FF Power
Antenna Type: MX14FIT456-01
Operating Freq. (MHz): 1978
Antenna Height (ft): 29.7
Antenna Gain (dBi): 13.3
Downtilt (degrees): 0.0
Feedline Loss (dB): 0.0
Tx Power (W): 40.0
No. of Channels: 4
Calc Angle 90.0 80.0 70.0 65.0 60.0 55.0 50.0 45.0 40.0 35.0 30.0 25.0 20.0 15.0 10.0 5.0 4.0 2.0
Solve for r, dx to antenna 26.7 27.1 28.4 29.5 30.9 32.6 34.9 37.8 41.6 46.6 53.4 63.2 78.1 103.3 153.9 306.6 383.1 765.7
Distance from Antenna Structure Base in Horizontal plane 0.0 4.7 9.7 12.5 15.4 18.7 22.4 26.7 31.9 38.2 46.3 57.3 73.4 99.7 151.6 305.5 382.2 765.3
Angle from Main Beam (reference to horizontal plane) 90.0 80.0 70.0 65.0 60.0 55.0 50.0 45.0 40.0 35.0 30.0 25.0 20.0 15.0 10.0 5.0 4.0 2.0
dB down from centerline (referenced to centerline) 33.3 27.6 26 25.1 25.8 29.9 27.3 17.3 13.6 16.3 28.3 23.5 14.5 20.8 26 3.8 2.1 0.3
Reflection Coefficient (1 to 4, 2.56 typical) 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56
Power Density (mW/cm^2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.01 0.02 0.01 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
Percent of Occupational Standard 0.01 0.04 0.05 0.05 0.04 0.01 0.02 0.20 0.38 0.16 0.01 0.02 0.09 0.01 0.00 0.07 0.06 0.02
Percent of General Population Standard 0.05 0.18 0.23 0.27 0.21 0.07 0.11 0.98 1.90 0.81 0.04 0.08 0.44 0.06 0.01 0.33 0.32 0.12
Max%: 1.90%
Instructions:
6) Spreadsheet calculates actual power density, then relates as Occupational or General Population percentage of FCC Standard.
7) An odd distance may be entered in the rightmost column of the lower table.
Estimated Radiated Emission
Single Emitter Far Field Model
Dipole/Wire/Yagi Antenna Types
1) Fill in Site Location, Site number, Date, Name of Person Responsible for Date, and enter File Name to ba saved as.
2) References to J4 refer to a point where the transmission line exits the equipment shelter and proceeds to the antenna(s). There is typically a connector located here where power measurements are made.
3) Enter Antenna Height (in feet to bottom of antenna), Antenna Gain (expressed as dBi, add 2.17 to dBd to obtain dBi), Antenna Size (vertical size in inches), Downtilt (in Degrees, enter zero if none),
Feedline loss from J4 to Antenna, and J4 Power (in watts).
4) From manufacturer's plots, or data sheet, input Angle from mainbeam and dB below mainbeam centerline.
5) Enter Reflection coefficient (2.56 would be typical, 1 for free space)
-0.01
0.00
0.01
0.01
0.02
0.02
0.0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
0.0 4.7 9.7 12.5 15.4 18.7 22.4 26.7 31.9 38.2 46.3 57.3 73.4 99.7 151.6 305.5 382.2 765.3
Po
wer
De
nsity
mW
/cm
^2
Perc
en
t o
f F
CC
Sta
nd
ard
Distance from Tower Base in the Vertical Plane (feet)Assumes level ground, normal to antenna mounting structure
Far Field ApproximationReference to Main Beam Centerline
% Occupational % General Public Power Density
1975 MHz (PCS)
Far Field Approximation
with downtilt variation
Location: Old Saybrook Center CT
Site #: 2-0523
Date: 09/22/21
Name: Stephen Nerkowski
File Name: Old Saybrook Center CT - FF Power
Antenna Type: MX14FIT456-01
Operating Freq. (MHz): 2120
Antenna Height (ft): 29.7
Antenna Gain (dBi): 14.7
Downtilt (degrees): 0.0
Feedline Loss (dB): 0.0
Tx Power (W): 40.0
No. of Channels: 4
Calc Angle 90.0 80.0 70.0 65.0 60.0 55.0 50.0 45.0 40.0 35.0 30.0 25.0 20.0 15.0 10.0 5.0 4.0 2.0
Solve for r, dx to antenna 26.7 27.1 28.4 29.5 30.9 32.6 34.9 37.8 41.6 46.6 53.4 63.2 78.1 103.3 153.9 306.6 383.1 765.7
Distance from Antenna Structure Base in Horizontal plane 0.0 4.7 9.7 12.5 15.4 18.7 22.4 26.7 31.9 38.2 46.3 57.3 73.4 99.7 151.6 305.5 382.2 765.3
Angle from Main Beam (reference to horizontal plane) 90.0 80.0 70.0 65.0 60.0 55.0 50.0 45.0 40.0 35.0 30.0 25.0 20.0 15.0 10.0 5.0 4.0 2.0
dB down from centerline (referenced to centerline) 29.2 26.3 25.4 25.8 27.7 29.5 28.4 26.4 20.8 15.7 21.1 19.5 31.5 19.2 45.3 5.6 3.3 0.7
Reflection Coefficient (1 to 4, 2.56 typical) 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56
Power Density (mW/cm^2) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.01 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
Percent of Occupational Standard 0.03 0.07 0.07 0.06 0.04 0.02 0.02 0.03 0.10 0.26 0.06 0.06 0.00 0.02 0.00 0.06 0.07 0.03
Percent of General Population Standard 0.17 0.33 0.37 0.31 0.18 0.11 0.12 0.17 0.50 1.28 0.28 0.29 0.01 0.12 0.00 0.30 0.33 0.15
Max%: 1.28%
Instructions:
6) Spreadsheet calculates actual power density, then relates as Occupational or General Population percentage of FCC Standard.
7) An odd distance may be entered in the rightmost column of the lower table.
Estimated Radiated Emission
Single Emitter Far Field Model
Dipole/Wire/Yagi Antenna Types
1) Fill in Site Location, Site number, Date, Name of Person Responsible for Date, and enter File Name to ba saved as.
2) References to J4 refer to a point where the transmission line exits the equipment shelter and proceeds to the antenna(s). There is typically a connector located here where power measurements are made.
3) Enter Antenna Height (in feet to bottom of antenna), Antenna Gain (expressed as dBi, add 2.17 to dBd to obtain dBi), Antenna Size (vertical size in inches), Downtilt (in Degrees, enter zero if none),
Feedline loss from J4 to Antenna, and J4 Power (in watts).
4) From manufacturer's plots, or data sheet, input Angle from mainbeam and dB below mainbeam centerline.
5) Enter Reflection coefficient (2.56 would be typical, 1 for free space)
0.00
0.00
0.00
0.01
0.01
0.01
0.01
0.01
0.0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
0.0 4.7 9.7 12.5 15.4 18.7 22.4 26.7 31.9 38.2 46.3 57.3 73.4 99.7 151.6 305.5 382.2 765.3
Po
wer
De
nsity
mW
/cm
^2
Perc
en
t o
f F
CC
Sta
nd
ard
Distance from Tower Base in the Vertical Plane (feet)Assumes level ground, normal to antenna mounting structure
Far Field ApproximationReference to Main Beam Centerline
% Occupational % General Public Power Density
2120 MHz (AWS)
Far Field Approximation
with downtilt variation
Location: Old Saybrook Center CT
Site #: 2-0523
Date: 09/22/21
Name: Stephen Nerkowski
File Name: Old Saybrook Center CT - FF Power
Antenna Type: VZ-MT6407-77A
Operating Freq. (MHz): 3730
Antenna Height (ft): 29.7
Antenna Gain (dBi): 23.4
Downtilt (degrees): 6.0
Feedline Loss (dB): 0.0
Tx Power (W): 30.2
No. of Channels: 4
Calc Angle 90.0 86.0 76.0 71.0 66.0 61.0 56.0 51.0 46.0 41.0 36.0 31.0 26.0 21.0 16.0 11.0 10.0 8.0
Solve for r, dx to antenna 26.7 26.8 27.5 28.3 29.2 30.5 32.2 34.4 37.1 40.7 45.5 51.9 61.0 74.6 97.0 140.1 153.9 192.0
Distance from Antenna Structure Base in Horizontal plane 0.0 1.9 6.7 9.2 11.9 14.8 18.0 21.6 25.8 30.7 36.8 44.5 54.8 69.6 93.2 137.5 151.6 190.1
Angle from Main Beam (reference to horizontal plane) 90.0 80.0 70.0 65.0 60.0 55.0 50.0 45.0 40.0 35.0 30.0 25.0 20.0 15.0 10.0 5.0 4.0 2.0
dB down from centerline (referenced to centerline) 23.06 22.8 23.6 26.25 29.08 25.49 24.19 28.8 28.85 20.69 18.06 20.49 15.83 17.7 12.92 2.79 1.96 0.5
Reflection Coefficient (1 to 4, 2.56 typical) 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56 2.56
Power Density (mW/cm^2) 0.04 0.04 0.03 0.02 0.01 0.02 0.02 0.01 0.01 0.03 0.04 0.02 0.04 0.02 0.03 0.15 0.15 0.14
Percent of Occupational Standard 0.79 0.84 0.66 0.34 0.17 0.35 0.42 0.13 0.11 0.59 0.87 0.38 0.81 0.35 0.62 3.07 3.08 2.77
Percent of General Population Standard 3.97 4.20 3.30 1.70 0.83 1.74 2.10 0.64 0.54 2.95 4.34 1.90 4.03 1.75 3.11 15.37 15.41 13.86
Max%: 15.41%
Instructions:
6) Spreadsheet calculates actual power density, then relates as Occupational or General Population percentage of FCC Standard.
7) An odd distance may be entered in the rightmost column of the lower table.
Estimated Radiated Emission
Single Emitter Far Field Model
Dipole/Wire/Yagi Antenna Types
1) Fill in Site Location, Site number, Date, Name of Person Responsible for Date, and enter File Name to ba saved as.
2) References to J4 refer to a point where the transmission line exits the equipment shelter and proceeds to the antenna(s). There is typically a connector located here where power measurements are made.
3) Enter Antenna Height (in feet to bottom of antenna), Antenna Gain (expressed as dBi, add 2.17 to dBd to obtain dBi), Antenna Size (vertical size in inches), Downtilt (in Degrees, enter zero if none),
Feedline loss from J4 to Antenna, and J4 Power (in watts).
4) From manufacturer's plots, or data sheet, input Angle from mainbeam and dB below mainbeam centerline.
5) Enter Reflection coefficient (2.56 would be typical, 1 for free space)
0.00
0.02
0.04
0.06
0.08
0.10
0.12
0.14
0.16
0.18
0.0
2.0
4.0
6.0
8.0
10.0
12.0
14.0
16.0
18.0
0.0 1.9 6.7 9.2 11.9 14.8 18.0 21.6 25.8 30.7 36.8 44.5 54.8 69.6 93.2 137.5 151.6 190.1
Po
we
r D
en
sity
mW
/cm
^2
Pe
rce
nt
of
FC
C S
tan
dard
Distance from Tower Base in the Vertical Plane (feet)Assumes level ground, normal to antenna mounting structure
Far Field ApproximationReference to Main Beam Centerline
% Occupational % General Public Power Density
3730.88 MHz (CBAND)
ATTACHMENT 4
ATTACHMENT 5
OLD SAYBROOK,CT
19 MAIN ST
Print Map It
Location 19 MAIN ST
MBLU 037/ 051/ / /
Acct# 00453000
Owner 231ST SRS LLC
Assessment $1,423,500 Appraisal $2,033,600
PID 3607
Building Count 1
Current Value
Appraisal
Valuation Year Improvements Land Total
2018 $1,538,600 $495,000 $2,033,600
Assessment
Valuation Year Improvements Land Total
2018 $1,077,000 $346,500 $1,423,500
Owner of Record
Owner 231ST SRS LLC
Co-Owner
Address PO BOX 656
YONKERS, NY 10702
Sale Price $3,000,000
Certificate
Book & Page 0667/0414
Sale Date 08/13/2021
Instrument 00
Ownership History
Ownership History
Owner Sale Price CertificateBook &
PageInstrument Sale Date
DCR1519 MAIN LLC $2,100,000 0623/1027 00 05/15/2017
PROSPECT
REALTY
PARTNERS LLC
$240,000 0340/0961 01/10/1997
Building Information
Building 1 : Section 1
Year Built: 1940
Living Area: 6,882
Building Attributes
Field Description
STYLE Strip Stores
MODEL Commercial
Grade Excellent
Stories: 1
Occupancy 4.00
Exterior Wall 1 Stucco/Masonry
Exterior Wall 2
ATTACHMENT 6