notice d’instructions atex et sil / atex and … · - zone 0, 1 ou 2 pour les gaz de groupes iia,...
TRANSCRIPT
1
Barrières Zener / Zener barriers :
bzg NOTICE D’INSTRUCTIONS ATEX ET SIL / ATEX AND SIL INSTRUCTION MANUAL
Régulateurs GEORGIN14-16 rue Pierre Sémard – BP 107 – 92323 CHATILLON cedex FranceTel. : +33 (0)1 46 12 60 00 – Fax : +33 (0)1 47 35 93 98Email : [email protected] Web : www.georgin.com
Belgique / BelgiumEmail: [email protected]
Vous devez lire avec une très grande attention toutes les instructions de cette notice et ne commencer l’installation que lorsque vous les aurez prises en compte. Ce matériel peut recevoir à ses bornes des tensions dangereuses. Si vous ne tenez pas compte de ces instructions, vous vous exposez à de graves dommages corporels et matériels. Avant de réaliser votre installation, vérifier que le modèle et l’alimentation conviennent à votre application. Le raccordement de ce matériel devra être réalisé en conformité à la réglementation en vigueur par un personnel qualifié
You must read carefully all the instructions of this manual. You must not start the installation before taking these instructions into account. This equipment might receive some hazardous voltages. If you do not consider these instructions, you risk serious corporal and material injuries. Before setting up the installation, check that both the model and power supply suit your application. The wiring of this equipment must be executed with the in forces rules by qualified staff.
FU-BZG-FRENDE-03-08-2018
1) INSTRUCTIONS DE MISE EN SERVICE1.1) FONCTIONLes barrières Zener type BZG … sont destinées à limiter l’énergie susceptible d’apparaître en zone explosible. Elles permettent de réaliser l’interface de signaux entre la zone ATEX et la zone sûre.1.2) UTILISATION ET MARQUAGE DU PRODUIT(en conformité avec la directive ATEX 2014/34/UE)Destination du matériel : Industries de surfaceType de protection : sécurité intrinsèque de construction «Ex ia» / Sécurité Ex nA [ia]Type de matériel : matériel associé devant impérativement être installé en zone sûre ou en zone 2 dans un coffret IP54 (voir §1.7.2.)Adapté pour interfacer du matériel de catégories 1, 2 ou 3 installé en : - Zone 0, 1 ou 2 pour les gaz de groupes IIA, IIB ou IIC (selon EN/CEI 60079-10-1)- Zone 20, 21 ou 22 pour les groupes de poussières IIIA, IIIB, IIIC (selon EN/CEI 60079-10-2) Attestation d’examen CE de type numéro: INERIS 11ATEX0024XCertificat de conformité IECEx: INE 11.0009XClassement ATEX /IECEx II (1) GD [Ex ia Ga] IIC ou [Ex ia Ga] IIB ou [Ex ia Da] IIICII 3 (1) G Ex nA [ia Ga] IIC T4 GcII 3 (1) G Ex nA [ia Ga] IIB T4 Gc1.3) CERTIFICATIONSCe produit, installé et utilisé conformément à cette notice utilisateur, a été déclaré conforme aux normes d’essais suivantes :ATEX : EN 60079-0 (2012) / EN 60079-11 (2012) / EN 60079-15 (2010) / IECEx : CEI 60079-0 (2011) / CEI 60079-11 (2011) / CEI 60079-15 (2010) /CEM : EN 61326-1 & EN 61000-6-2DBT : EN/CEI 61010-1SIL : EN 61508 (SIL 2 ou SIL 3 suivant application)1.4) PARAMETRES DE SECURITEvoir tableau pages 3 & 41.5) CARACTERISTIQUES ELECTRIQUESvoir tableau pages 3 & 41.6) CARACTERISTIQUES MECANIQUESEncombrement : voir schéma page 2Poids : ≈ 200gMatériaux du boitier : PolycarbonateIndice de protection : IP20 1.7) INSTALLATIONLe matériel est destiné à une association conforme à la sécurité intrinsèque, l’installation devra être conforme à la norme EN/CEI 60079-14 en particulier le § 12.1.7.1) FIXATION ET MONTAGE Les équipements sont prévus pour être fixés sur rail DIN type OMEGA.Le montage s’effectue en présentant l’accroche DIN de la barrière partie haute sur le rail puis verrouillage en appliquant un effort vers le bas.Pour démonter la barrière du rail, placer le tournevis dans l’encoche et faire descendre l’accroche DIN avec un effet de levier. Voir schéma page 2.La borne de terre doit être raccordée à un réseau de terres équipotentielles par un fil de section 4 mm² minimum.Il est possible d’isoler l’attache DIN de la BZG du rail DIN par un kit d’isolement (nous consulter).La position horizontale ou verticale de la barrière est indifférente.La bzg dispose d’un porte étiquette amovible en face avant.Pour l’ouvrir, placer un tournevis dans l’encoche située sur le haut de la face avant. Voir schéma page 2.1.7.2) LIEU D’INSTALLATIONPour installation en zone sure :Les équipements doivent être installés en atmosphère non explosive, dans un environnement sain, à l’abri de la condensation, des poussières corrosives ou conductrices.La température ambiante doit être comprise entre -20°C et +60°C.Ne pas oublier cependant que la durée de vie d’un matériel électronique se réduit quand sa température d’utilisation augmente (approximativement de moitié par 10°C).
Toute précaution devra être prise pour éviter la proximité d’organe pouvant échauffer l’appareil par rayonnement ou susceptible de générer des rayonnements électromagnétiques supérieurs à 10V/m.L’installation doit être effectuée par un personnel qualifié conformément à la norme EN/CEI 60079-14.Pour installation en zone 2 :La température ambiante doit être comprise entre -20°C et +60°C.Installation dans un coffret IP 54 minimum conforme à la norme EN/CEI 60079-15 et EN/CEI 60079-0.Le nombre de barrières montées dans le coffret doit être en accord avec la puissance maximale pouvant être dissipée par le boitier pour respecter le classement en températureUn système de brides doit être installé à proximité de la barrière bzg pour éviter l’arrachement des connecteurs (bride permettant la retenue des câbles d’une force d’au moins 15N).1.7.3) RACCORDEMENT ELECTRIQUELes raccordements électriques doivent être exécutés HORS TENSION par des fils de 0.2mm² à 2,5 mm² maximum.Pour le branchement, se référer au verso (schéma type 1 à 6 suivant modèles)La liaison de terre doit être raccordée par un conducteur de 4mm² minimum.Le couple de serrage des vis des bornes de raccordements doit être compris entre 0.4Nm et 0.5Nm.1.7.4) CONDITIONS SPECIALES POUR UNE UTILISATION SURELes bornes de sécurité intrinsèque ne doivent être raccordées qu’à du matériel de sécurité intrinsèque ou conforme au §5.7 de la norme EN/CEI 60079-11. De plus, l’association des matériels et du câble de liaison doit être compatible du point de vue de la sécurité intrinsèque.La valeur efficace maximum de la tension de défaut que l’on admet pouvoir apparaitre accidentellement de façon permanente aux bornes d’entrée des barrières bzg est de 250V.Conditions supplémentaires pour l’utilisation de la bzg dans un système de fonction instrumenté de sécurité (SIL) :L’utilisation doit déterminer le niveau de SIL en fonction du type de système instrumenté de sécurité de la bzg (sollicitation en mode continu ou à la sollicitation). Se référer à la déclaration dcsil-bzg-fren disponible sur www.georgin.com. Conformément à la norme EN 61508, la bzg doit être soumis à des tests périodiques et à une politique de maintenance.Dans le cas d’une utilisation en mode sollicitation, le niveau de SIL ne peut être maintenu que dans une période de test TL et que pendant un temps de réparation donné (MTTR).Le signal électrique parcourant la bzg doit faire l’objet d’une surveillance afin de détecter toute défaillance du système de sécurité.1.7.5) CHEMINEMENT DES CABLESLa nature et le cheminement des câbles allant en zone explosible (câbles de sécurité intrinsèque) doivent être conformes aux prescriptions de §6.1, 6.2.1 et 6.3 de la norme EN/CEI 60079-11.Toute précaution doit être prise pour éviter des couplages électromagnétiques avec d’autres câbles pouvant générer des tensions ou courants dangereux.Les câbles de sécurité intrinsèque doivent être bridés de manière à éviter un contact fortuit avec d’autres câbles en cas d’arrachement du bornier.2) MAINTENANCEPrécautions à observer lors de la maintenanceLe démontage doit s’effectuer HORS TENSION. En cas de suspicion de panne ou de panne franche, retourner l’appareil à nos services ou mandataires, seuls habilités à procéder à une expertise.Certains modèles sont équipés en face avant d’une ou deux DEL rouge permettant de visualiser la présence d’un courant dans la boucle (ex :bzg787LP+).3) CONTACTEZ NOUSCette notice est disponible en plusieurs langues ainsi que l’attestation d’examen CE de type et le certificat IECEx sur www.georgin.com
1) START-UP INSTRUCTIONS1.1) FUNCTIONBZG Zener barriers are designed to limit energy which may appear in hazardous area. It allows the realization of signals interface between the ATEX area and the safe area.
1.2) USE AND MARKING (in compliance with the directive ATEX 2014/34/EU)Location of the equipment: Surface industriesMethod of protection: Intrinsic Safety (I.S.): «Ex ia» / Ex nA [ia] safety.Type of equipment: associated equipment which must be installed in the safe area or in zone 2 in an IP54 housing (see §1.7.2.)Suitable for interface equipment of category 1, 2 or 3, installed in:- Zone 0, 1 or 2 for gas of group IIA, IIB or IIC (according to EN/IEC 60079-10-1)- Zone 20, 21 or 22 for dusts of group IIIA, IIIB, or IIIC (according to EN/IEC 60079-10-2). EC type Examination Certificate number: INERIS 11ATEX0024XIECEx Conformity certificate: INE 11.0009XATEX / IECEx classification:II (1) GD [Ex ia Ga] IIC ou [Ex ia Ga] IIB ou [Ex ia Da] IIICII 3 (1) G Ex nA [ia Ga] IIC T4 GcII 3 (1) G Ex nA [ia Ga] IIB T4 Gc
1.3) CERTIFICATIONSThis product installed according to this instructions sheet is declared in conformity with the following standards:ATEX: EN 60079-0 (2012) / EN 60079-11 (2012) / EN 60079-15 (2010) / IECEx: IEC 60079-0 (2011) / IEC 60079-11 (2011) / IEC 60079-15 (2010) /CEM: EN 61326-1 & EN 61000-6-2DBT: EN/IEC 61010-1SIL: EN 61508 (SIL 2 or SIL 3 according to application)
1.4) SAFETY PARAMETERSSee table overleaf page 3 & 41.5) ELECTRICAL DATASee table overleaf page 3 & 4
1.6) MECHANICHAL DATADimension see overleaf page 2Weight: ≈ 200gHousing material: PolycarbonateProtection index: IP20
1.7) INSTALLATIONThe equipment is part of an association following the I.S. rules. The installation must comply to the EN/IEC 60079-14 standard, and in particular, § 12.
1.7.1) FIXINGThe equipment is designed to be mounted on a OMEGA type DIN rail.Mount the equipment by placing the DIN bracket of the upward part of the barrier on the rail. Then, lock by pushing downward.Insert the screw driver in the hole and pull down in order to unlock the barrier. See drawing page 2.The ground terminal must be connected to an equipotential earth’s network with minimum 4 mm² wire section.A mounting kit allows isolating the DIN bracket of the BZG from the rail (contact us).The equipment can be mounted either in the horizontal or vertical position.The bzg is equipped with a label holder on the front.To open it, insert a screw driver in the hole . See drawing page 2.
1.7.2) LOCATIONSafe zone locationEquipments must be installed in a non explosive atmosphere, in an environment free of condensation, corrosive and conducting dusts.The ambient temperature must be between -20°C and +60°C.
However, note that the lifetime of any electronic equipment is reduced when working temperature increases (Around 50% less by 10°C temperature increase).Careful precautions must be taken to avoid the proximity of apparatus likely to heat up the housing by hot radiation or likely to cause electromagnetic radiation higher than 10V/m.Zone 2 locationThe ambient temperature must be between -20°C and +60°C.In compliance with the EN/IEC 60079-15 et EN/IEC 60079-0 standard the equipment must be placed in an IP54 (minimum) housing.In compliance with the EN/IEC 60079-14 the installation must be realized by qualified staff.To respect the temperature classification, the number of barriers mounted in the housing must respect the maximal power that the housing can dissipate.To prevent a disconnection of the connectors, install a flange system nearby the barrier.
1.7.3) ELECTRICAL WIRINGElectrical wiring must be executed when DE-ENERGIZED, from 0.2mm² to 2.5 mm² maximum wires.Refer to the “Wiring” paragraph overleaf.The ground must be connected with a 4 mm² conductor.The coupling torque of the connection terminal screws must be between 0.4Nm and 0.5Nm.
1.7.4) SPECIAL CONDITIONS FOR A SAFE USEI.S. terminals must only be connected to I.S. equipment or in compliance with § 5.7 of the EN/IEC 60079-11 standard. Moreover, the association of the equipment with the connecting cable must be compatible with regard to the I.S. rules.The maximum voltage default accepted to appear permanently by accident to the bzg barrier input terminals is 250VAdditional requirements to use the bzg in a Safety Instrumented Function (SIL):The user must determine the SIL level according to the type of Safety Instrumented System of the bzg (continuous solicitation mode or stress mode).Refer to the certificate dcsil-bzg-fren.According to the EN 61508 standard, the bzg must be periodically tested and must be subject to a maintenance policy. For stress mode use, the SIL can only be maintained during a TL test period and for a mean time to repair (MTTR). The electrical signal that goes through the bzg must be monitored to detect any failure of the security system.
1.7.5) CABLES PATHThe type and the path of the cables going into the explosive area (I.S. cables) must comply with the prescriptions of §6.1, 6.2.1 and 6.3 of the EN / IEC 60079-11 standard.Particular precautions must be taken to avoid electromagnetic couplings with other cables likely to cause hazardous voltages or currents.I.S. cables must be clamped in such a way to avoid any accidental contact with other cables in case the terminal is accidentally pulled off.
2) MAINTENANCEPrecautions to be observed during maintenanceDismounting must be executed when DE-ENERGIZED.If a fault is suspected or observed, return it to our services or mandatory authorised to expertise or repair the equipment.Some models are equipped with one or two red LED on the front to observe the presence of current in the loop (eg:bzg787LP+) 3) CONTACT USThis manual is available in several languages as well as the EC type Examination Certificate and IECEx Certificate on our website www.georgin.com
FU-BZG-FRENDE-03-08-2018
2
ENCOMBREMENT / DIMENSION / ABMESSUNGEN (mm)
DEMONTAGE / DISMOUNTING / DEMONTAGE
1
2
ATEX- UND SIL-BETRIEBSANLEITUNG
Régulateurs GEORGIN14-16 rue Pierre Sémard – BP 107 – 92323 CHATILLON cedex FranceTel. : +33 (0)1 46 12 60 00 – Fax : +33 (0)1 47 35 93 98Email : [email protected] Web : www.georgin.com
Belgique / BelgiumEmail: [email protected]
Die Anweisungen in der Betriebsanleitung sind aufmerksam durchzulesen. Erst mit der Installation beginnen, wenn alle Anweisungen beachtet wurden. An den Geräteklemmen können gefährliche Spannungen auftreten. Bei Nichtbeachtung der Anweisungen setzen Sie sich der Gefahr von schweren Personen- und Sachschäden aus. Vor der Installation prüfen, dass die Variante und die Spannungsversorgung für die jeweilige Anwendung geeignet sind. Nach den geltenden Vorschriften hat der Anschluss des Geräts durch Elektrofachkräfte zu erfolgen.
FU-BZG-FRENDE-03-08-2018
1) ANWEISUNGEN FÜR DIE INBETRIEBNAHME1.1) FUNKTIONDie BZG Zenerbarrieren dienen der Begrenzung der Energie, die im explosionsgefährdeten Bereich auftreten kann. Durch sie kann die Signalschnittstelle zwischen dem ATEX-Bereich und dem sicheren Bereich hergestellt werden.1.2) EINSATZ UND GERÄTEKENNZEICHNUNG(nach der ATEX-Produktrichtlinie 2014/34/EU)Bestimmung des Geräts: ÜbertageeinsatzZündschutzart: eigensicher, Schutzniveau «Ex ia» / Ex nA [ia]Betriebsmitteltyp: Zugehöriges Betriebsmittel, das zwingend im sicheren Bereich oder in Zone 2 in einem IP54-Gehäuse installiert werden muss (siehe Absatz 1.7.2.).Geeignet zum Verbinden von Betriebsmitteln der Kategorien 1, 2 oder 3, die in folgenden Zonen installiert sind: - Zone 0, 1 oder 2 für Gasgruppen IIA, IIB oder IIC (nach EN/IEC 60079-10-1)- Zone 20, 21 oder 22 für Staubgruppen IIIA, IIIB, IIIC (nach EN/IEC 60079-10-2)EG-Baumusterprüfbescheinigung Nr.: INERIS 11ATEX0024XIECEx-Konformitätsbescheinigung: INE 11.0009XATEX- / IECEx-Klassifikation:II (1) GD [Ex ia Ga] IIC oder [Ex ia Ga] IIB oder [Ex iaD Da] IIICII 3 (1) G Ex nA [ia Ga] IIC T4 GcII 3 (1) G Ex nA [ia Ga] IIB T4 Gc1.3) ZERTIFIZIERUNGENDas entsprechend der Betriebsanleitung installierte und benutzte Gerät ist konform mit folgenden Prüfnormen:ATEX : EN 60079-0 (2012)/ EN 60079-11 (2012)/ EN 60079-15 (2010)/ IECEx : CEI 60079-0 (2011) / CEI 60079-11 (2011) / CEI 60079-15 (2010) /EMV : EN 61326-1 & EN 61000-6-2Niederspannungsrichtlinie : EN/IEC 61010-1 SIL : EN 61508 (SIL 2 oder SIL 3 je nach Anwendung)1.4) SICHERHEITSPARAMETERsiehe Tabelle Seiten 3 & 41.5) ELEKTRISCHE KENNWERTEsiehe Tabelle Seiten 3 & 41.6) MECHANISCHE EIGENSCHAFTENAbmessungen: siehe Schema Seite 2 Gewicht: ca. 200g
Gehäusematerial: PolycarbonatSchutzart: IP201.7) INSTALLATIONDas Gerät ist für eine eigensichere Verbindung bestimmt. Die Installation muss entsprechend der Norm EN/IEC 60079-14 und insbesondere Absatz 12 erfolgen.1.7.1) BEFESTIGUNG UND MONTAGE Die Betriebsmittel sind für die Befestigung an einer DIN-Hutschiene bestimmt. Zur Montage wird die DIN-Klemmbefestigung der Barriere am oberen Teil der Tragschiene aufgesetzt und durch Drücken nach unten eingerastet.Zur Demontage der Barriere von der Tragschiene den Schraubendreher in den Schlitz einsetzen und die DIN-Klemmbefestigung durch einen Hebeleffekt nach unten führen. Die Erdungsklemme muss durch einen Leiter mit einem Querschnitt von mindestens 4 mm² an eine Erdungsanlage mit Potentialausgleich angeschlossen werden.Die DIN-Klemmbefestigung der BZG kann durch ein Isolierset von der DIN-Tragschiene isoliert werden (bitte anfragen).Die Barriere kann unterschiedslos in horizontaler oder vertikaler Position montiert werden. Die BZG verfügt über einen abnehmbaren Schildträger an der Frontseite.Zum Öffnen des Schildträgers einen Schraubendreher in den Schlitz oben an der. 1.7.2) EINBAUORTFür die Installation im sicheren Bereich:Die Geräte müssen in nicht explosionsfähiger Atmosphäre, in einer sauberen Umgebung, geschützt vor Kondensation und korrosivem bzw. leitendem Staub installiert werden. Die Umgebungstemperatur muss zwischen -20°C und +60°C liegen.Dabei ist allerdings zu beachten, dass sich die Lebensdauer eines elektronischen Betriebsmittels bei Erhöhung der Betriebstemperatur verringert (etwa um die Hälfte pro Temperaturanstieg von 10°C).Es sind alle notwendigen Vorkehrungen zu treffen, um die Nähe zu Bauteilen, die das Gerät durch Strahlung erwärmen oder eine elektromagnetische Strahlung über 10V/m erzeugen können, zu vermeiden.Die Installation muss entsprechend der Norm EN/IEC 60079-14 durch eine qualifizierte Fachkraft erfolgen.Für die Installation in Zone 2:
Die Umgebungstemperatur muss zwischen -20°C und +60°C liegen.Installation in einem Gehäuse mit Mindestschutzart IP 54 entsprechend den Normen EN/IEC 60079-15 und EN/IEC 60079-0.Die Anzahl der im Schaltschrank montierten Barrieren muss mit der maximalen Leistung übereinstimmen, die zur Einhaltung der Temperaturklassifikation vom Gehäuse zerstreut werden kann. In der Nähe der BZG-Barriere ist ein Laschensystem zu installieren, um das Herausreißen der Steckverbinder zu verhindern (Lasche zur Kabelbefestigung mit einer Rückhaltekraft von mindestens 15N).1.7.3) ELEKTRISCHER ANSCHLUSSDie elektrischen Anschlüsse müssen SPANNUNGSFREI durch Leiter mit einem Querschnitt von maximal 0.2 mm² bis 2,5 mm² hergestellt werden.Für den Anschluss bitte auf der Rückseite nachschauen (Schaltbild Typ 1 bis 6 je nach Variante). Der Erdanschluss muss durch einen Leiter mit einem Querschnitt von mindestens 4mm² hergestellt werden. Das Anzugsmoment der Schrauben an den Anschlussklemmen muss zwischen 0.4 Nm und 0.5 Nm betragen.1.7.4) SONDERBEDINGUNGEN FÜR SICHEREN EINSATZDie eigensicheren Klemmen dürfen nur an eigensichere Betriebsmittel oder Betriebsmittel nach Absatz 5.7 der Norm EN/IEC 60079-11 angeschlossen werden.Außerdem muss die Verbindung der Betriebsmittel mit dem Verbindungskabel in Bezug auf die Eigensicherheit kompatibel sein.Der maximale Effektivwert der Fehlerspannung, der unbeabsichtigt über längere Zeit an den Eingangsklemmen der BZG-Barrieren auftreten kann, beträgt 250V.Zusätzliche Bedingungen für den Einsatz der BZG in einem elektronischen System mit funktionaler Sicherheit (SIL):Für den Einsatz ist die Sicherheitsanforderungsstufe in Abhängigkeit vom Typ des sicherheitstechnischen Systems der BZG festzulegen (Beanspruchung im Dauerbetrieb oder bei Beanspruchung). Bitte in der dcsil-bzg-fren Erklärung nachschlagen, die auf www.georgin.com abrufbar ist.Entsprechend der Norm EN 61508 muss die BZG periodischen Tests und einem Wartungsprogramm unterzogen werden. Beim Einsatz im Beanspruchungsmodus kann die
Sicherheitsanforderungsstufe nur für einen Testzeitraum TL und eine mittlere Reparaturzeit (MTTR) aufrecht erhalten werden. Das elektrische Signal, das die BZG durchläuft, muss überwacht werden, um Störungen des Sicherheitssystems zu erkennen.1.7.5) KABELVERLEGUNGDie Art und Verlegung der in den explosionsgefährdeten Bereich geführten Kabel (eigensichere Kabel) müssen den Vorschriften von Absatz 6.1, 6.2.1 und 6.3 der Norm EN/ IEC 60079-11 entsprechen.Es sind alle notwendigen Vorkehrungen zu treffen, um elektromagnetische Kopplungen mit anderen Kabeln, die gefährliche Spannungen oder Ströme erzeugen können, zu vermeiden. Die eigensicheren Kabel müssen so befestigt werden, dass ein unbeabsichtigtes Berühren mit anderen Kabeln beim Herausreißen der Klemmleiste vermieden wird.2) WARTUNGBei der Wartung zu beachtende VorsichtsmaßnahmenDie Demontage muss SPANNUNGSFREI erfolgen.Beim Verdacht eines Ausfalls oder einem vollständigen Ausfall das Gerät an unseren Kundendienst bzw. Beauftragten zurücksenden, die als einzige berechtigt sind, eine Begutachtung durchzuführen.Bestimmte Varianten sind frontseitig mit einer bzw. zwei roten LED ausgestattet, durch die das Vorhandensein eines Stroms in der Schleife angezeigt werden kann (z.B.: bzg787LP+).3) KONTAKTDie Betriebsanleitung sowie die EG-Baumusterprüfbescheinigung und das IECEx-Zertifikat sind in mehreren Sprachen auf www.georgin.com abrufbar
3
Type
Modèle/ Model/
Varianten
Paramètres de sécurité intrinsèque / Intrinsicaly safe param
eters / Eigensichere parameter
Schéma Théorique/
Theoretical diagram/
Theoretisches Diagramm
Caractéristiques électriques / Electrical data / Elektrische kennwerteBornes/
Terminals/ Klemmen
Ro(Ω)Uo(V)
Io(mA)
Po(mW
)Lo IIC(µH)
Co IIC(µF)
L/R IIC(µH/Ω)
Lo IIB(µH)
Co IIB(µF)
L/R IIB(µH/Ω)
Bornes/Terminals/ Klemmen
Una(V)
Ina(nA)
U(a)(V)
Bornes/Terminals/ Klemmen
I(t)(µA)
U(e)(V)
Bornes/Terminals/ Klemmen
Ifm(mA)
RL(Ω)Tol.
+/- (%)
Type 1
BZG710+3\4
489.6
197470
9163.6
753664
26302
2/12/T
8.8100
9.5
2/T
108.6
2/32/32/32/32/32/32/32/32/32/32/32/32/3
10054.6
5BZG715+
3\495
14.4151
5451551
0.6765
62034.18
26112
8513.8
1012
100103.6
5BZG715P+
3\444
14.4322
1159343
0.6731
13704.18
12312
10013.8
1012
10050.6
5BZG803
3\4242
17.271
3047139
0.353117
285592.06
46816
5516.6
1015.5
100252.6
5BZG801
3\4142
17.2121
5202434
0.35368
97392.06
27316
7016.6
1015.5
100153.6
5BZG802
3\453
17.2324
1393339
0.35325
13572.06
10216
10016.6
1015.5
10059.6
5BZG722+
3\4142
21147
7711645
0.18846
65811.27
18419
7019.6
1019
100153.6
5BZG728+
3\4284
27.396
6543875
0.08854
155000.683
21824
5026.8
1024.9
50311.3
5BZG728L+
3\4284
27.396
6543875
0.08854
155000.683
21824
5026.8
1024.9
502V+
311.35
BZG728P+3\4
23127.3
118802
25730.088
4410294
0.683177
2450
26.810
24.950
248.35
BZG728LP+3\4
23127.3
118802
25730.088
4410294
0.683177
2450
26.810
24.950
248.3 +2V
5BZG729P+
3\4165
27.3165
11251308
0.08832
52340.683
12624
5026.8
1024.9
50180.3
5BZG729LP+
3\4165
27.3165
11251308
0.08832
52340.683
12624
5026.8
1024.9
50180.3 +
2V5
Type 2
BZG760AC
3\T44
4.9111
1362911
100261
116421000
10432/T
1100
4.62/T1/T
101.2
2/3100
50.65
4\T44
4.9111
1362911
100261
116421000
10431/T
1100
4.63\4
885.6
6389
892954
40035718
10001600
2/11
100-
1/4100
50.65
3\T\\4\T22
4.9221
273728
100130
29111000
521
BZG764+
3\T240
9.640
9621792
3.6368
8716726
14742/T
855
9.22/T1/T
107
2/3100
50.65
4\T240
9.640
9621792
3.6368
8716726
14741/T
855
9.23\4
46810.3
2256
756732.63
640302693
182559
2/18
55-
1/4100
50.65
3\T\\4\T118
9.681
1935448
3.6184
2179226
737
BZG761+
3\T44
9.6214
511776
3.670
310626
2782/T
8100
9.22/T1/T
107
2/3100
50.65
4\T44
9.6214
511776
3.670
310626
2781/T
8100
9.23\4
8910.3
115294
26962.63
12110784
18483
2/18
100-
1/4100
50.65
3\T\\4\T22
9.6428
1022194
3.635
77626
139
BZG767+
3\T95
14.4151
5451551
0.6765
62034.18
2612/T
1285
13.82/T1/T
1012
2/3100
103.65
4\T95
14.4151
5451551
0.6765
62034.18
2611/T
1285
13.83\4
19015.8
83328
51510.478
10820606
2.88434
2/112
85-
1/4100
103.65
3\T\\4\T47
14.4303
1089388
0.6733
15514.18
131
BZG796+
3\T286
25.288
5574548
0.10764
181910.82
2552/T
2240
24.42/T
1022.5
2/350
311.35
4\T370
18.951
24113663
0.262148
546541.6
5901/T
2240
18.83\4
64725.9
40256
227750.1
13991099
0.77556
2/122
40-
1/T10
16.81/4
50401.3
53\T\\4\T
16122.5
139783
18290.154
457315
1.08182
BZG788+
3\T284
27.396
6543875
0.08854
155000.683
2182/T
2450
26.82/T
1024.9
2/350
311.35
4\T48
9.6197
471914
3.675
365726
3021/T
2450
9.83\4
33328
84588
50430.083
6020170
0.65242
2/124
50-
1/T10
81/4
5062.3
53\T\\4\T
4112.1
293889
4142.75
401657
18.7160
BZG788L+
3\T284
27.396
6543875
0.08854
155000.683
2182/T
2450
26.82/T
1024.9
2/350
311.35
4\T48
9.6197
471914
3.675
365726
3021/T
2450
9.83\4
33328
84588
50430.083
6020170
0.65242
2/124
50-
1/T10
81/4
5062.342V +
53\T\\4\T
4112.1
293889
4142.75
401657
18.7160
Type 3
BZG787+3\T
31327.3
87594
46890.088
6018755
0.683239
2/T24
4526.8
2/T1/T10
24.92/3
50341.3
54\T
00
00
--
--
--
1/T24
4526.8
3\4314
2889
6254457
0.08357
178290.65
2272/1
2445
-1/4
500.9V+ 11.3
53\T\\4\T
31327.3
87594
46890.088
6018755
0.683239
BZG787P+3\T
23727.3
115788
26690.088
4510678
0.683181
2/T24
5026.9
2/T1/T10
24.92/3
50252.6
54\T
00
00
--
--
--
1/T24
5026.9
3\4237
28118
8292538
0.08343
101510.65
1722/1
2450
-1/4
500.9V+ 11.3
-3\T\\4\T
23727.3
115788
26690.088
4510678
0.683181
BZG787LP+3\T
23727.3
115788
26690.088
4510678
0.683181
2/T24
5026.8
2/T1/T10
24.92/3
50252.6
54\T
00
00
--
--
--
1/T24
5026.8
3\4237
28118
8292538
0.08343
101510.65
1722/1
2450
-1/4
500.9V+ 11.3
-3\T\\4\T
23727.3
115788
26690.088
4510678
0.683181
Type 5
BZG757D+3\T or 4
97.1
7521342
6213.5
2662
240106
2/1 or T6/5 or T
6100
6.82/T6/T
106.3
2/3100
13.65
7\T or 89
7.1752
134262
13.526
62240
1066/7
10013.6
5
BZG764D+
3\T or 4240
9.640
9621791
3.6368
8716726
14732/1 or T
855
8.92/T6/T
108
2/3100
252.65
7\T or 4240
9.640
9621791
3.6368
8716726
14736/5 or T
855
8.93\7
46810.3
2256
756732.63
639302693
182559
2/68
55-
6/7100
252.65
3\4 \\ 7\8118
9.681
1935447
3.6184
2179226
736
BZG2710+
3\T or 448
9.6197
470916
3.675
366426
3022/1 or T
8.8100
9.5 2/T6/T
10 8.6
2/3100
54.65
7\T or 448
9.6197
470916
3.675
366426
3026/5 or T
8.8100
9.53\7
9710.3
106271
31752.63
13112698
18524
2/68.8
100-
6/7100
54.65
3\4 \\ 7\824
9.6394
942229
3.638
91426
151
BZG761D+3\T or 4
449.6
214511
7763.6
693106
26278
2/1 or T8
1008.9
2/T6/T10
82/3
10050.6
57\T or 4
449.6
214511
7763.6
693106
26278
6/5 or T8
1008.9
3\789
10.3115
2942696
2.63120
1078418
4832/6
8100
-6/7
10050.6
53\4 \\ 7\8
229.6
4281022
1943.6
34776
26139
BZG2715+3\T or 4
9514.4
151545
15510.67
656203
4.18261
2/1 or T12
8513.8
2/T6/T10
122/3
100103.6
57\T or 4
9514.4
151545
15510.67
656203
4.18261
6/5 or T12
8513.8
3\7190
15.883
3285151
0.478108
206062.88
4342/6
1285
-6/7
100103.6
53\4 \\ 7\8
4714.4
3031089
3880.67
331551
4.18131
BZG2715P+3\T or 4
4414.4
3221159
3430.67
311370
4.18123
2/1 or T6/5 or T
12100
13.82/T6/T
1012
2/3100
50.65
7\T or 444
14.4322
1159343
0.6731
13704.18
1236/7
10050.6
5
BZG28033\T or 4
24217.2
71304
71390.353
11728559
2.06468
2/1 or T16
5516.6
2/T6/T10
15.52/3
100252.6
57\T or 4
24217.2
71304
71390.353
11728559
2.06468
6/5 or T16
5516.6
3\7489
18.638
17824426
0.27200
977051.64
8012/6
1655
-6/7
100252.6
53\4 \\ 7\8
12117.2
141608
17840.353
597139
2.06234
BZG28013\T or 4
14217.2
121520
24340.353
689739
2.06273
2/1 or T16
7016.6
2/T6/T10
15.52/3
100153.6
57\T or 4
14217.2
121520
24340.353
689739
2.06273
6/5 or T16
7016.6
3\7286
18.665
3048329
0.27117
333191.64
4682/6
1670
-6/7
100153.6
53\4 \\ 7\8
7117.2
2421040
6080.353
342434
2.06137
BZG28023\T or 4
5317.2
3241393
3390.353
251357
2.06102
2/1 or T6/5 or T
16100
16.62/T6/T
1015.5
2/3100
59.65
7\T or 453
17.2324
1393339
0.35325
13572.06
1026/7
10059.6
5BZG2722+
3\T or 4142
21147
7711645
0.18846
65811.27
1842/1 or T6/5 or T
1970
19.62/T6/T
1019
2/3100
153.65
7\T or 4142
21147
7711645
0.18846
65811.27
1846/7
100153.6
5
BZG796D+
3\T or 4286
25.288
5574547
0.10763
181900.82
2552/1 or T
2240
242/T
10 23
2/350
311.35
7\T or 4370
18.951
24113663
0.262147
546531.6
5906/5 or T
1640
18.53\7
64725.9
40256
227740.1
13891098
0.77555
2/623
40-
6/T10
176/7
50401.3
53\4 \\ 7\8
16122.5
139783
18280.154
457315
1.08181
BZG2728+3\T or 4
28427.3
96654
38750.088
5415500
0.683 218
2/1 or T6/5 or T
2450
26.82/T6/T
1024.9
2/350
311.35
7\T or 4284
27.396
6543875
0.08854
155000.683
2186/7
50311.3
5BZG2728L+
3\T or 4284
27.396
6543875
0.08854
155000.683
2182/1 or T6/5 or T
2450
26.82/T6/T
1024.9
2/350
311.3 + 2V5
7\T or 4284
27.396
6543875
0.08854
155000.683
2186/7
50311.3 + 2V
5BZG2728P+
3\T or 4231
27.3118
8022573
0.08844
102940.683
1772/1 or T6/5 or T
2450
26.82/T6/T
1024.9
2/350
248.35
7\T or 4231
27.3118
8022573
0.08844
102940.683
1776/7
50248.3
5BZG2728LP+
3\T or 4231
27.3118
8022573
0.08844
102940.683
1772/1 or T6/5 or T
2450
26.82/T6/T
1024.9
2/350
248.3 + 2V 5
7\T or 4231
27.3118
8022573
0.08844
102940.683
1776/7
50248.3 + 2V
5
BZG788D+3\T or 4
28427.3
96654
38750.088
5415500
0.683217
2/1 or T24
5026.9
2/T10
252/3
50311.3
57\T or 4
489.6
197471
9143.6
753656
26301
6/5 or T8
508.9
3\7333
2884
5885042
0.08360
201700.65
2412/6
24.550
-6/T
10 7
6/750
62.35
3\4 \\ 7\841
12.1293
889414
1.3240
16568.4
160BZG2729P+
3\T or 4165
27.3165
11251308
0.08831
52340.683
1262/1 or T6/5 or T
2450
26.82/T6/T
1024.9
2/350
180.35
7\T or 4165
27.3165
11251308
0.08831
52340.683
1266/7
50180.3
5BZG2729LP+
3\T or 4165
27.3165
11251308
0.08831
52340.683
1262/1 or T6/5 or T
2450
26.82/T6/T
1024.9
2/350
180.3 + 2V5
7\T or 4165
27.3165
11251308
0.08831
52340.683
1266/7
50180.3 + 2V
5
Type 11
BZG787D+3\T or 4
31327.3
87594
46880.088
5918755
0.683239
2/1 or T24
4527
2/T6/T10
252/3
50341,3
57\T or 4
00
00
--
--
--
6/5 or T24
4527
3\7314
2889
6254457
0.08356
178280.65
2272/6
2445
-6/7
500.9V + 11.3
-3\4 \\ 7\8
31327.3
87594
46880.088
5918755
0.683239
BZG787DP+
3\T or 4237
27.3115
7882669
0.08845
106770.683
1802/1 or T
2450
27
2/T6/T10
25
2/350
260.35
7\T or 40
00
0-
--
--
-6/5 or T
2450
273\7
23728
118829
25370.083
4210150
0.65171
2/624
50-
6/750
0.9V + 11.3
53\4 \\ 7\8
23727.3
115788
26690.088
4510677
0.683180
Type 4
BZG789+
3\T593
27.346
31616551
0.088112
662020.683
4502/T 1/T 5/T 6/T
2035
26.82/T1/T5/T
1024.9
2/350
658.35
7\T593
27.346
31616551
0.088112
662020.683
450
4\T & 8\T0
00
0-
--
--
-10
24.91/4
500.9V + 11.3
-
3\\7\T293
27.393
6334138
0.08856
165510.683
2252/16/5
2035
-10
24.96/7
50658.3
53\4 & 7\8
58328
48333
157330.083
10762934
0.65427
3\\7\4 & 3\\7\8294
2895
6663933
0.08353
157330.65
21410
24.95/8
500.9V + 11.3
-
BA
RR
IÈRES + / + B
AR
RIER
S / + BA
RR
IEREN
FU-B
ZG-FR
EN
DE
-03-08-2018
Una :Ina : U(e) :U(a) :RL :Tol :lfm :T :\\ :\ :
Tension maximum d’utilisation en Ex nA [ia] pour un classement en température T4 : -20°C / +60°C / Maximum use voltage in Ex nA [ia] for a T4 class of temperature : -20°C / +60°C / Maximale Betriebsspannung für Ex nA [ia] für die Klasse T4 bei Temperatur : -20°C / +60°CCourant maximum d’utilisation en Ex nA [ia] pour un classement en température T4 : -20°C / +60°C / Maximum use current in Ex nA [ia] for a T4 class of temperature : -20°C / +60°C / Maximaler Betriebsstrom für Ex nA [ia] für die Klasse T4 bei Temperatur : -20°C / +60°CTension pour laquelle un courant de fuite inférieur ou égal à I(t) est assuré / Voltage for which a leakage current lower or equal to I(t) is assured / Spannung für den der Leckstrom kleiner oder gleich I(t) gewährleistet istTension maximum d’entrée / Maximum voltage input / Maximale EingangsspannungRésistance de ligne / Line resistance / LeitungswiderstandTolérance de la résistance de ligne / Tolerance of line resistance / Toleranz des LeitungswiderstandCourant maximum pouvant traverser la barrière (avant destruction) / Maximum current that can pass through the barrier (without destruction) / Maximalstrom der durch die Barriere fließen kann (ohne Zerstörung)Terre / Earth / ErdeEn parallèle / In parallel / ParallelPar rapport à / Compared to / Im Vergleich zu
4
Type
Modèle/ Model/
Varianten
Paramètres de sécurité intrinsèque / Intrinsicaly safe param
eters / Eigensichere parameter
Schéma théorique/
Theoretical diagram/
Theoretisches Diagramm
Caractéristiques électriques / Electrical data / Elektrische kennwerteBornes/
Terminals/ Klemmen
Ro(Ω)Uo(V)
Io(mA)
Po(mW
)Lo IIC(µH)
Co IIC(µF)
L/R IIC(µH/Ω)
Lo IIB(µH)
Co IIB(µF)
L/R IIB(µH/Ω)
Bornes/Terminals/ Klemmen
Una(V)
Ina(nA)
U(a)(V)
Bornes/Terminals/ Klemmen
I(t)(µA)
U(e)(V)
Bornes/Terminals/ Klemmen
Ifm(mA)
RL(Ω)Tol.
+/- (%)
Type 7
BZG728-3\T or 4
287-27.3
-95648
39390.088
5415758
0.683219
2/T2/1-24
50-26.8
2/T10
-24.92/3
50311.3
5
1/450
311.35
BZG728L- 3\T or 4
287-27.3
-95648
39390.088
5415758
0.683219
2/T2/1-24
50-26.8
2/T10
-24.92/3
50311.3
5
1/450
311.35
Type 8
BZG796-
3\T286
-25.2-88
5574547
0.10763
181900.82
2552/T
-2240
-24.42T
10-22.5
2/350
311.35
4\T369
-9.6-26
6253459
3.6577
21383626
23081/T
-2240
-18.83\4
647-25.9
-40256
227740.1
13891098
0.77555
1T10
-16.81/4
50401.3
53\\4 \ T
161-18.4
-114525
27250.285
6710903
1.69270
2/1-22
40-
Type 9
BZG796D-
3\T or 4286
-25.2-88
5574547
0.10763
181900.82
2552/1 or T
-2140
242/T
1023
2/350
311.35
7\T or 8370
-18.9-51
24113663
0.262147
546531.6
5906/5 or T
-1640
18.53\7
647-25.9
-40256
227740.1
13891098
0.77555
2/6-22
40-
6/T10
176/7
50401.3
53\\7 \ T
161-22.5
-139783
18280.154
457315
1.08181
BZG2728-3\4
287-27.3
-95648
39390.088
5415758
0.683219
2/1 or T 6/5 or T
-2450
-26.82/T6/T
10-24.9
2/350
311.35
7\8287
-27.3-95
6483939
0.08854
157580.683
2196/7
50311.3
5
BZG2728L-3\4
287-27.3
-95648
39390.088
5415758
0.683219
2/1 or T 6/5 or T
-2450
-26.82/T6/T
10-24.9
2/350
311.3 + 2V5
7\8287
-27.3-95
6483939
0.08854
157580.683
2196/7
50311.3 + 2V
5
Type 15
BZG710AC3\T or 4
529.8
185455
10403.3
784161
23313
2/1 2/T
8.8100
9.3
2/T
108.6
2/3
10059.6
5BZG715AC
3\T or 494
14.4152
5471543
0.6765
61734.18
26012
8513.5
1011
100103.6
5BZG715PAC
3\T or 444
14.4323
1164341
0.6731
13644.18
12212
10013.5
1011
10050.6
5BZG803AC
3\T or 4235
17.273
3116764
0.36114
270572.11
45816
5516
1015
100 252.6
5BZG801AC
3\T or 4143
17.2120
5162455
0.3669
98192.11
27616
7016
1015
100 153.6
5BZG802AC
3\T or 453
17.2322
1382342
0.3626
13692.11
10316
10016
1015
10059.4
5BZG722AC
3\T or 4142
20.5144
7381716
0.20348
68651.33
19319
7019
1018
100153.6
5BZG728AC
3\T or 4285
27.797
6713778
0.08553
151100.663
21224
5027
1025
50 311.3
5BZG728PAC
3\T or 4225
27.7123
8492358
0.08542
94300.663
16824
5027
1025
50245.3
5BZG729PAC
3\T or 4161
27.7172
1190-
--
47950.663
11924
5027
1025
50180.3
5
Type 10
BZG764AC
3\T933
11.212
33255810
1.841077
100000012.6
43082/T
1027
10.62/T1/T
109.6
2/3100
1003.65
4\T933
11.212
33255810
1.841077
100000012.6
43081/T
1027
10.63\4
186622.4
1266
2558100.156
5381000000
1.092154
1/4100
1003.65
3\\4 \ T466
11.224
6663952
0.156528
2558101.09
21542/1
1027
-
BZG766AC
3\T141
11.279
2205755
1.84161
2302212.6
6462/T
1070
112/T1/T
1010.1
2/3100
153.65
4\T141
11.279
2205755
1.84161
2302212.6
6461/T
1070
113\4
28322.4
79440
57550.156
8023022
1.09323
1/4100
153.65
3\\4 \ T71
11.2157
4401438
0.15680
57621.09
3232/1
1070
-
Type 13
BZG905DAC
3\T or 425
4.8187
2241017
100158
40691000
6342/1
3.5100
3.82/T6/T
101.1
2/3100
30.65
7\T or 825
4.8187
2241017
100158
40691000
6346/5
3.5100
3.83\7
519.6
187448
10173.6
794069
26317
6/7100
30.65
3\\7 \ T12
4.8374
448254
10079
10171000
3172/6
7100
-
BZG908DAC
3\T or 4189
7.238
6824691
12.7519
98765216
20792/1
5.550
7.52/T6/T
105.7
2/350
211.35
7\T or 8189
7.238
6824691
12.7519
98765216
20796/5
5.550
7.53\7
37814.4
38136
246910.65
25998765
4.071039
6/750
211.35
3\\7 \ T94
7.276
1376188
12.7260
24753216
10402/6
1150
-
BZG765DAC
3\T or 453
7.8147
2891637
8.8123
6548115
4922/1
6100
7.52/T6/T
107
2/3100
59.65
7\T or 853
7.8147
2891637
8.8123
6548115
4926/5
6100
7.53\7
10615.7
147577
16370.487
616548
2.95246
6/7100
59.65
3\\7 \ T26
7.8295
578409
8.861
1637115
2462/6
12100
-
BZG765DPAC3\T or 4
257.8
306599
3808.8
591522
115237
2/1 6/5
6100
7.52/T6/T
107
2/3100
30.65
7\T or 825
7.8306
599380
8.859
1522115
2376/7
10030.6
5
BZG903DAC
3\T or 495
8.690
1944364
6.2183
1745655
7342/1
770
8.22/T6/T
107.5
2/3100
103.65
7\T or 8143
8.660
1299819
6.2275
3927655
11026/5
770
8.23\7
23817.2
72309
68180.36
11427275
2.11459
6/7100
153.65
3\\7 \ T57
8.6150
3221571
6.2110
628755
4412/6
1470
-
BZG901DAC
3\T or 471
8.6120
2582454
6.2137
981955
5512/1
7100
8.22/T6/T
107.5
2/3100
78.65
7\T or 871
8.6120
2582454
6.2137
981955
5516/5
7100
8.23\7
14317.2
120516
24540.36
689819
2.11275
6/7100
78.65
3\\7 \ T35
8.6241
516613
6.268
245455
2752/6
14100
-
BZG902DAC3\T or 4
258.6
334717
3186.2
491272
55198
2/1 6/5
7100
8.22/T6/T
107.5
2/3100
30.65
7\T or 825
8.6334
717318
6.249
127255
1986/7
10030.6
5
BZG764DAC
3\T or 4933
11.212
33100 000
1.841077
100 00012.6
43082/1
8.527
10.62/T6/T
109.6
2/3100
1003.65
7\T or 8933
11.212
33100 000
1.841077
100 00012.6
43086/5
8.527
10.63\7
186622.4
1266
100 0000.156
538100 000
1.092154
6/7100
1003.65
3\\7 \ T466
11.224
6664383
1.84540
100 00012.6
21612/6
1727
-
BZG766DAC
3\T or 4141
11.279
2205755
1.84161
2302212.6
6462/1
1070
10.62/T6/T
1010
2/3100
153.65
7\T or 8141
11.279
2205755
1.84161
2302212.6
6466/5
1070
10.63\7
28322.4
79440
57550.156
8023022
1.09323
6/7100
153.65
3\\7 \ T71
11.2157
4401440
1.8480
576212.6
3232/6
2070
-
BZG772DAC
3\T or 471
11.2157
4401438
1.8480
575512.6
3232/1
9100
10.62/T6/T
1010
2/3100
78.65
7\T or 871
11.2157
4401438
1.8480
575512.6
3236/5
9100
10.63\7
14222.4
157880
14380.156
405755
1.09161
6/7100
78.65
3\\7 \ T35
11.2314
880359
1.8440
143912.6
1612/6
18100
-
BZG766DPAC
3\T or 478
12.3157
4821437
1.2873
57518.1
2952/1
8.595
11.52/T6/T
1010.5
2/3100
85.65
7\T or 878
12.3157
4821437
1.2873
57518.1
2956/5
8.595
11.53\7
15624.5
157963
14370.118
365751
0.88147
6/7100
85.65
3\\7 \ T39
12.3315
963359
1.2836
14378.1
1472/6
1795
-
BZG907DAC
3\T or 4288
14.450
18114024
0.67196
5609826
7872/1
1250
142/T6/T
1012.5
2/3100
303.65
7\T or 8189
14.476
2716233
0.67131
2493226
5246/5
1250
143\7
47828.7
60433
97390.077
8238957
0.618328
6/7100
203.65
3\\7 \ T114
14.4126
4512246
0.6778
898626
3152/6
2450
-
Type 12
BZG906AC
3\T21
6.1290
439423
3781
1694880
3242/T
5100
5.92/T1/T
103
2/3100
25.65
4\T21
6.1290
439423
3781
1694880
3241/T
5100
5.93\4
426.1
145219
169437
1626777
880648
1/4100
25.65
3\\4 \ T10
6.1579
877105
3740
105880
1622/1
5100
-
BZG778AC
3\T256
27.7108
745-
--
122390.663
1902/T
2440
272/T1/T
1025
2/350
281.35
4\T369
27.775
516-
--
255360.663
2751/T
2440
273\4
62927.7
44305
--
-73132
0.663466
1/450
401.35
3\\4 \ T152
27.7182
1261-
--
42730.663
1122/1
2440
-
Type 6
BZG755AC3\T
143.2
214169
774100
2113097
1000843
2/T 1/T
250
4.32/T1/T
10.7
2/3 50
26.30.15
4\T9
3.2321
253344
100140
13771000
1401/4
5026.3
0.153\4
253.9
157151
1442100
2355760
1000941
2/12
50-
BZG756AC
3\T14
3.2214
169774
100211
30971000
8432/T1/T6/T
250
4.32/T1/T6/T
10.7
2/3 50
26.30.15
4\T9
3.2321
253344
100140
13771000
1401/4
5026.3
0.157\T
93.2
321253
344100
1401377
1000140
3\425
3.9157
1511442
100235
57601000
9412/1/6
250
-6/7
5026.3
0.154\\7 \ 3
193.9
196188
925100
1883700
1000753
Type 14
BZG757AC
3\T4\T8\T7\T9
3.2332
261323
100136
323100
1362/T1/T5/T6/T
250
4.3
2/T1/T5/T6/T
10.7
2/350
21.35
3\4 or 3\7 or 3\8 or 4\7 or 4\8 or 7\8
193.9
203195
866100
182866
100182
1/450
21.35
3\\4 \ 7 or 3\\4 \ 8 or 3\\7 \ 4 or 3\\7 \ 8or 3\\8 \ 7 or 3\\8 \ 4 or 4\\7 \ 3 or 4\\7 \ 8 or 4\\8 \ 3 or 4\\8 \ 7or 7\\8 \ 3 or 7\\8 \ 4
143.9
270260
487100
137487
100137
2/1/5/62
50-
5/850
21.35
3\\4 \ 7\\8 or 3\\7 \ 4\\8 or 3\\8 \ 4\\7
93.9
405390
216100
91216
10091
6/750
21.35
BA
RR
IÈRES - et A
C / - and A
C B
AR
RIER
S / - und AC
BA
RR
IEREN
FU-B
ZG-FR
EN
DE
-03-08-2018
Una :Ina : U(e) :U(a) :RL :Tol :lfm :T :\\ :\ :
Tension maximum d’utilisation en Ex nA [ia] pour un classement en température T4 : -20°C / +60°C / Maximum use voltage in Ex nA [ia] for a T4 class of temperature : -20°C / +60°C / Maximale Betriebsspannung für Ex nA [ia] für die Klasse T4 bei Temperatur : -20°C / +60°CCourant maximum d’utilisation en Ex nA [ia] pour un classement en température T4 : -20°C / +60°C / Maximum use current in Ex nA [ia] for a T4 class of temperature : -20°C / +60°C / Maximaler Betriebsstrom für Ex nA [ia] für die Klasse T4 bei Temperatur : -20°C / +60°CTension pour laquelle un courant de fuite inférieur ou égal à I(t) est assuré / Voltage for which a leakage current lower or equal to I(t) is assured / Spannung für den der Leckstrom kleiner oder gleich I(t) gewährleistet istTension maximum d’entrée / Maximum voltage input / Maximale EingangsspannungRésistance de ligne / Line resistance / LeitungswiderstandTolérance de la résistance de ligne / Tolerance of line resistance / Toleranz des LeitungswiderstandCourant maximum pouvant traverser la barrière (avant destruction) / Maximum current that can pass through the barrier (without destruction) / Maximalstrom der durch die Barriere fließen kann (ohne Zerstörung)Terre / Earth / ErdeEn parallèle / In parallel / ParallelPar rapport à / Compared to / Im Vergleich zu