new prestandard cen/ts 14751: tofd on weld seams
TRANSCRIPT
LudwigshafenVerbund Site
n professionaln customer focusedn cost aware
New Prestandard CEN/TS 14751 :
TOFD on Weld Seams
ECNDT 2006Berlin, 25.-29. September 2006We.2.7.2
Dr.-Ing. Andreas HechtPlant Inspection / Materials Engineering
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 2
LudwigshafenVerbund SiteEuropean Prestandard CEN/TS 14751
TOFD on Weld Seams
n TOFD Time-of-Flight Diffraction Technique
n Existing codes / recommendations / standards on TOFD
n Implementation of DIN CEN/TS 14751 within other European NDT – Standards on weld-testing
n European Prestandard DIN CEN/TS 14751
n Further European Activities
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 3
LudwigshafenVerbund Site
S
Principle of TOFD
Diffraction (not Reflection)
diffraction of the ultrasonic wave atthe edges of a defect
- rigid mechanical coupling
of transmitter and receiver
- no scanning, movement only along the weld
- preferably longitudinal waves
- wide angles of divergence required
- received signals of low amplitude
T R
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 4
LudwigshafenVerbund SiteEuropean Prestandard CEN/TS 14751
TOFD on Weld Seams
n TOFD Time-of-Flight Diffraction Technique
n Existing codes / recommendations / standards on TOFD
n Implementation of DIN CEN/TS 14751 within other European NDT – Standards on weld-testing
n European Prestandard DIN CEN/TS 14751
n Further European Activities
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 5
LudwigshafenVerbund SiteTOFD on Weld Seams
Existing codes / recommendations / standards on TOFD
Europen BS 7706 (national) December 1993
Guide to calibration and setting-up of the ultrasonic TOFD-technique for the detection, location and sizing of flaws
n ENV 583-6 (European pre-standard) January 1997 TOFD as a method for defect detection and sizing
n CEN/TS 14751 (CEN Technical specification) November 2004 Welding – Use of TOFD for examination of welds
Othern ASME Code Case 2235 since 1998, at present: 2235-9 from Oct. 2005
Use of ultrasonic examination in lieu of radiography(see also interpretation VIII-1-98-41)
n ASTM E 2373-04 July 2004Standard practice for the ultrasonic TOFD-technique
n 2006 ASME Code, Section V 2006Article 4, Mandatory Appendix III, Non-mandatory Appendix L and N new
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 6
LudwigshafenVerbund SiteEuropean Prestandard CEN/TS 14751
TOFD on Weld Seams
n TOFD Time-of-Flight Diffraction Technique
n Existing codes / recommendations / standards on TOFD
n Implementation of DIN CEN/TS 14751 within other European NDT – Standards on weld-testing
n European Prestandard DIN CEN/TS 14751
n Further European Activities
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 7
LudwigshafenVerbund SiteTOFD on Weld Seams
Implementation of TOFD-prestandard into European NDT-weld-testing system created by CEN/TC 121/SC 5
Constraints / Explanationsn Table is valid for fabrication
inspections within the EUn Main standard EN 12062 has to
be reviewed:l EN 25817 à EN ISO 5817l TOFD to be implemented
n ENV 583-6 from 1997 acts as a basic standard
n Weld testing standard CEN/TS 14751 completed
n Technical Specification (TS)means: „state-of-the-art is not yet stable enough“
n EN-standard for acceptance levels in progress
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 8
LudwigshafenVerbund SiteTOFD on Weld Seams
European Working Group
n CEN/TC 121/SC 5B/WG 2 resolution from October 1999
n Formation of a working-groupHecht (chairman) D BASFChardome B AIB VincotteChauveau F Institute de Soudure (IS) Hughes GB Health & Safety Executive (HSE)Kenzie GB The Welding Institute (TWI)Pers-Anderson S Westinghouse TRCRasmussen DK FORCESchlengermann D GE InspectionVandriessche B AIB VincotteVerkooijen NL SonovationWalaszek F CETIM
n 9 meetings from August 2000up to October 2002
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 9
LudwigshafenVerbund SiteEuropean Prestandard CEN/TS 14751
TOFD on Weld Seams
n TOFD Time-of-Flight Diffraction Technique
n Existing codes / recommendations / standards on TOFD
n Implementation of DIN CEN/TS 14751 within other European NDT – Standards on weld-testing
n European Prestandard DIN CEN/TS 14751
n Further European Activities
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 10
LudwigshafenVerbund SitePrestandard CEN/TS 14751
European Frontpage
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 11
LudwigshafenVerbund SitePrestandard CEN/TS 14751
Contents
Foreword1 Scope2 Normative references3 Terms and definitions4 General remarks on the capabilities of the technique5 Examination levels6 Information required prior to testing7 Requirements for personnel and equipment8 Preparation for testing8.2 Set-up of probes9 Testing of base metal10 Range- and sensitivity setting11 Weld testing12 Interpretation and analysis of TOFD images13 Test reportAnnex A (informative): Reference blocksAnnex B (informative): Examples of typical scans
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 12
LudwigshafenVerbund SitePrestandard CEN/TS 14751
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 13
LudwigshafenVerbund SitePrestandard CEN/TS 14751
Capabilities and Limitations
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 14
LudwigshafenVerbund SitePrestandard CEN/TS 14751
Limited capability of detection at surfaces
- Dead zone at scanning-surface, caused by pulse-length- Zone of limited sensitivity at opposite-surface, caused by interference between tip-diffraction
and backwall; depends of wave-length and pulse-length
n Measurements of Kreier (Innotest) and Brekow (BAM)published at ECNDT 1998
n notch 5 mm deep: diffraction signal of notch tip clearly visiblenotch 1 mm deep: no definite diffraction signal
Comparison pulse-echo / TOFDacc. to Schmitz and Müller(IZfP-Saarbrücken)
notch signal?
crack-depth
no crack
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 15
LudwigshafenVerbund SitePrestandard CEN/TS 14751
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 16
LudwigshafenVerbund SitePrestandard CEN/TS 14751
proposed table for EN 12062 - revision
n Proposal made by German experts of CEN/TC 121/SC 5B/WG 2 (UT)
n Has to be accepted by CEN/TC 121/SC 5B (NDT of welds)and CEN/TC 121 (Welding)
Table A7: time-of-flight diffraction technique (TOFD)
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 17
LudwigshafenVerbund SitePrestandard CEN/TS 14751
8.2 Set-up of Probes
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 18
LudwigshafenVerbund SitePrestandard CEN/TS 14751
similar toRT - film interpretation
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 19
LudwigshafenVerbund SitePrestandard CEN/TS 14751
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 20
LudwigshafenVerbund SitePrestandard CEN/TS 14751
What is a relevant TOFD-indication ?
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 21
LudwigshafenVerbund SitePrestandard CEN/TS 14751
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 22
LudwigshafenVerbund SitePrestandard CEN/TS 14751
Annex B1: Satisfactory Image
S E
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 23
LudwigshafenVerbund SitePrestandard CEN/TS 14751
Annex B1: Gain Setting too low
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 24
LudwigshafenVerbund SitePrestandard CEN/TS 14751
Ánnex B1: Gain Setting too High
from CEN/TS 14751
from ASME V 2006
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 25
LudwigshafenVerbund SitePrestandard CEN/TS 14751
Annex B1: Coupling Losses
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 26
LudwigshafenVerbund SitePrestandard CEN/TS 14751
Unsatisfactory Image from On-Site-Inspection (not included)
n gain-setting slightly to highn coupling lossesn electronic trigger-problems
n result:„no relevant indications“
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 27
LudwigshafenVerbund SitePrestandard CEN/TS 14751
Annex B2: Indication from Opposite Surface
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 28
LudwigshafenVerbund SitePrestandard CEN/TS 14751
Annex B3: Indication with measurable length and height
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 29
LudwigshafenVerbund SitePrestandard CEN/TS 14751
Annex B3: Geometrical Indication
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 30
LudwigshafenVerbund SiteEuropean Prestandard CEN/TS 14751
TOFD on Weld Seams
n TOFD Time-of-Flight Diffraction Technique
n Existing codes / recommendations / standards on TOFD
n Implementation of DIN CEN/TS 14751 within other European NDT – Standards on weld-testing
n European Prestandard DIN CEN/TS 14751
n Further European Activities
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 31
LudwigshafenVerbund SiteFurther
European Activities
n practical use of CEN/TS 14751 on-site:l get experienced with the provisions of the TSl review after 3 years and decision taken of transfer of TS into an EN or notl DIN EN ISO 17025: „there is no need to qualify / validate standardized techniques“
n preparation of an European standard on TOFD – acceptance levelsl draft prepared by CEN/TC 121/SC 5B/WG 2l ready for 5-months inquiry at CEN/TC 121
n review of EN 12062 necessaryl implementation of TOFD (CEN/TS 14751 + accept.lev.)
n European TOFDPROOF – projectl http://www.mpa-lifetech.de/TOFD/l organized by EPERC
Andreas Hecht, BASF AG ECNDT-Berlin, Sept. 2006, We.2.7.2 32
LudwigshafenVerbund SiteA Christmas Card
from Bjarne Larsenin good fun
For a happy andTOFD-free new year !