mx100
TRANSCRIPT
March 2003 MX100 Regional Training
MX100 Introduction
March 2003 MX100 Regional Training
Product LOGO
March 2003 MX100 Regional Training
Base PlateDifferent size for 1 to 6 modules.
MX100 Hardware Components
Main ModuleI/O Modules
March 2003 MX100 Regional Training
Compact flash memory card slot for data backup
Ethernet100-Base-TX,10Base-T
Auto-switch
Dip SWChange operating mode
Operating Mode indicator
Data acquisition engine controlling up to 6 I/o modules in one system.
MX100 Main Module
March 2003 MX100 Regional Training
I/O Module
4chHigh-speeduniversal inputmodule
10chMedium-speeduniversal inputmodule
10chHigh-speeddigital inputmodule
10chdigital outputmodule
Fastest measurement interval : 10ms
In of case TC/RTD, fastest measurement interval is 50 ms
Input : DCV/TC/RTD/DI
Fastest measurementinterval : 100ms Input : DCV/TC/RTD/DI
Fastest measurement
Interval : 10ms
Input : DI
Output interval :100msOutput : SPST relay (make contact)
March 2003 MX100 Regional Training
MX100 Features
PC Font-end System allowing Flexible Construction High Speed & Multi-channel Measurement
4ch module with 10msec measurement interval 10ch module with 100msec measurement interval Scalable from 4 channels to hundreds channels 3 individual sampling speed can run in one system
High Withstand Voltage (Reinforced Insulation) 3700Vrms(1minute), 600Vrms/Vdc(working voltage)
between input terminal and case
Data Protection Compact flash card for back-up the data while communication down
Open Architecture, Others Modular construction 100Base-TX Ethernet standard Disconnect-able terminal, external screw terminal
March 2003 MX100 Regional Training
100Base-TX
PC Front-end
To Network
Up to 20 units with MXLOGGER- 24ch/10msec- 300ch/100msec- 1200ch/1sec
Base plate
Main module with Ethernet, Compact flash card slot
Input/outputmodule
March 2003 MX100 Regional Training
Scalable
From 1 module model to 6 module model can be Configured according to measurement channels
March 2003 MX100 Regional Training
Multi Measurement Interval
100msec100msec10msec10msec 10sec10sec
3 individual sampling speed in one system
Setting example
Measurement intervals are set separately for each module.
March 2003 MX100 Regional Training
CH1CH2
….
.
CH(n)
CH(n-1)
V12 * V1
Vmax=600Vrms/Vdc from groundin case of 1 system.
Module1
Module(n/10)
CH10
Vmax=600Vrms/Vdc between modules
CH(n-9)
- In case of 10ch module, 150VACrms(50/60Hz) is a maximum noise
voltage between channels in one module. And, the voltage between channels in one module is also restricted by IEC1010 6.3.
- In case of 4ch module, 250Vrms/Vdc is a maximum voltage between
channels in one module
n=600/V1
Common Mode Voltage Performance(Double Insulation)
n * V1
….
.
March 2003 MX100 Regional Training
Common Mode Voltage Performance(Double Insulation)
Comparison table between Darwin and MX100
V1, V3 V2
10ms AI (4ch)
Allowable Common mode Voltage
600Vrms/Vdc 250Vrms/Vdc
Test Voltage (1min) 3700Vrms,50/60Hz
2300Vrms,50/60Hz
100ms AI (10ch) Allowable Common mode Voltage
600Vrms/Vdc 120Vrms/Vdc(SELV 250VACrms noise voltage, 50/60Hz)
Test Voltage (1min) 3700Vrms, 50/60Hz 1000Vrms, 50/60Hz
Darwin Allowable Common mode Voltage
160Vrms/Vdc(SELV 250VACrms noise voltage, 50/60Hz)
120Vrms/Vdc(SELV 150VACrms noise voltage, 50/60Hz)
Test Voltage (1min) 1500Vrms, 50/60Hz 1000Vrms, 50/60Hz
Aモジュール
Bモジュール
V1
V2
V3
Module A
Module B
V1
V2
V3
March 2003 MX100 Regional Training
Technical Resource
High breakdown voltage solid state relay
High breakdown voltage solid state relay •3 individual sampling
interval in one system•100 Base-TX standard•Compact flash standard
•3 individual sampling interval in one system•100 Base-TX standard•Compact flash standard
•Measurement of true parallel multi-channel•CH Synchronizing
•Measurement of true parallel multi-channel•CH Synchronizing
Iso.
SCC
Iso.
SCC
Iso.
SCC
Iso.
SCC
ASIC
SCC
ASIC
ASIC
CPUEthernet
ROM RAM
Power
CF
コ ン ト ロ ー ル ユ ニ ッ ト10ch/100ms AI4ch/10ms AI
3700V withstanding transformer
Control unit10ch/100msec AI4ch/10msec AI
High reliable serial bus with high speed simultaneous data transmission
High reliable serial bus with high speed simultaneous data transmission
March 2003 MX100 Regional Training
Data Back-up with CF Card
Support up to 2G bytes card
Start data storage at communication error Cable error
PC power fail, hung-up
Others
Re-start data transfer to PC automatically after the communication recovers
Communication True
Fail
True
File storage PC HD File A
MX CFFile B
PC HDFile C
March 2003 MX100 Regional Training
Data Back-up with CF Card
number ofchannels
measurementinterval
32M 128M 512M
10ms approx. 2 hours approx. 9 hours approx. 36 hours
100ms approx. 21 hours approx. 3.5 days approx. 15 days
500ms approx. 4.5 days approx. 18.5 days approx. 75.5 days
2s approx. 18 days approx. 75.5 days approx. 303 days
10ms approx. 54 minutes approx. 3.5 hours approx. 15 hours
100ms approx. 9 hours approx. 37 hours approx. 6 days
500ms approx. 45 hours approx. 7.5 days approx. 31.5 days
2s approx. 7.5 days approx. 31.5 days approx. 126 days
10ms approx. 18 minutes approx. 75 minutes approx. 5 hours
100ms approx. 3.5 hours approx. 15 hours approx. 2.5 days
500ms approx. 18 hours approx. 3 days approx. 12.5 days
2s approx. 3 days approx. 12.5 days approx. 50 days
60ch
10ch
24ch
Data Storage length
March 2003 MX100 Regional Training
Disconnect-able Terminal
Disconnect-able!!
Reduce re-wiring time when changing test- target and/or calibration.
March 2003 MX100 Regional Training
External Connectivity
- Screw terminal- Better RJC uniformity
Screw terminal can be used only for 10ch AI module and 10ch DI module.
March 2003 MX100 Regional Training
Others
- Connector cover - DIN rail mounting
March 2003 MX100 Regional Training
Basic specifications
Number of modules, units: Up to 6 modules / 1 main module
(10ms 24 ch, 100ms 60 ch/unit)
Up to 20 units connectable through MX100 enhanced software
Filter: Time constant=Measurement period x N,
N=5,10,20,25,40,50,100
Selectable N number depends on measurement period.
Interface: 100 Base-TX
Compact flash slot: Type II x 1, Specially designed for memory card
Alarm (main module): 2 levels/ch
Calculation (main module): Difference, scaling
Main Module
March 2003 MX100 Regional Training
Basic specifications
10 ch DI 10 ch DONumber of channels 10 ch 10 chInput and output types Non-voltage contact/TTL O.C/ SPST relay Level(5V logic)Measurement/output period minimum 10 ms minimum100 ms
Digital input/output module
4 ch high-speed module 10 ch scanner moduleNumber of channels 4 ch 10 chFastest measuring period 10 ms (50 ms for TC/RTD) 100 msMeasurement period Up to three types of intervals per system (on a module basis) 10, 50, 100, 200, 500ms, 1, 2, 5, 10, 20, 30, 60s Input ranges DCV/TC/RTD/DI DCV/TC/RTD/DI
DCV : 20mV, 60mV, 200mV, 2V, 6V, 20V, 100V TC : R,S,B,K,E,J,T,L,U,N,W,KpvsAu7Fe
RTD : Pt100, Pt50, NI100, NI120, Cu10 etc. DI : Non-voltage contact / Level(5V logic)Integration time: 1.67ms, 16.7ms, 20ms, 36.67ms, 100ms, 200ms Determined by the measurement periodMeasurement accuracy Integration time 16.7ms or longer 0.05% of rdg. + 5digits @2V rangeWithstanding voltage Between input terminal and case 3700VAC(50/60Hz) for 1 min. 3700VAC(50/60Hz) for 1 min. Between channels in one module 2300VAC(50/60Hz) for 1 min. 1000VAC(50/60Hz) for 1 min. (RTD also isolated) (b terminal common)
Analog input module
March 2003 MX100 Regional Training
MX100 DA100 Aims
Alarm
Shared by the main unit and PC softwareMain unit: 2 levels/channel
Upper/lower limits, upper/lower limits of difference
PC software: Implements by combining computation and command DORate-of-change alarm implementable
<>
Completely done on the main unit4 levels/channelUpper/lower limits, upper/lower limits of differenceRate-of-change alarm
Flexible alarm system implementableUsing the resources of the computation channels
Computation function
Shared by the main unit and PC softwareMain unit: Difference computation, scaling,
software filterPC software: Computation function provided as a
standard function
>
Completely done on the main unitDifference, scaling, moving average
Optional computation
function
Provided as a standard function. Darwin-/M1-level computation possible by the PC software. <>
Completely done on the main unit
Operation expressions easier to understand・ Constant description・ Total number of characters (40 → 250)・ C-language-like operator
Report function None. Use of the Excel macro, etc. < Provided as an option of /M3
Communications function
Ethernet only.Initial setup simplified such as automatic detection, automatic setup of IP address, etc.Binary-only format
<>
Ethernet, GP-IB, RS232, RS485ASCII command, binary/ASCII data
Simple setupHigh-speed setupDevelopment of self-made program supported by APIReduced number of communications types
Maintenance Update through the CF card slot, backing up function when communications disconnected, etc. > None Easy serviceability
Differences between MX100 and DA100 (2)
March 2003 MX100 Regional Training
MX100 DA100 Aims
System configuration
- PC-Base plate-Control unit-I/O Module
>
- PC-Basic/enhanced main unit-Subunit-I/O module-Communications module
Simple configuration covering a wide range of channels
Module types 10msAI,100msAI,DI,DO <
10ch20ch30ch UniversalmV/TCSingle-phase/three-phase power monitor120ohm /350ohm NDIS distortionDI-input-dedicated, mA inputPulse inputCurrent/voltage analog outputCommunications
Reducing the module types.Considering the real effects of each module.
Measurement cycle Maximum speed of 10 msMulti-interval of 3 types >>
Maximum speed of 500 msSynchronized with the cycle of the slowest module
High-speed measurementCoexistence of high speed and high stability
Withstand voltage 3700 V >> 1500 V Cell, electrolytic cell
Number of input points
60 channels/unit1200 channels/system <>
60 channels/subunit300 channels at the maximumMore channels connectable with the DAQLOGGER
Multi-channel measurement
Differences between MX100 and DA100 (1)
March 2003 MX100 Regional Training
MX100 Software Concept
MX Standard Software- Ready to run control software
-MX100 broadcast search (UDP) and Automatic module/controller detection-Always monitoring, once connection is made, even in background-All hardware options configurable via MXStandard
-Advanced Data logging -Independently log up to three scan groups -Record/log interval to log every N scans -Manual and Automatic start and stop conditions
-Advanced viewer -One to Four independent Viewer areas -”Mark” comment on live data, stored into logfile -Parallel cursors on
-Data Export-Excel, ASCII, Lotus
March 2003 MX100 Regional Training
MX100 Software ConceptMX Additional Software -Standalone Viewer
-View and Analyze recorded data-Cursor on all scan groups in parallel-Statistics or export data on selected regions
-MX Calibrator with wizards -Independently log up to three scan groups -Record/log interval to log every N scans -Manual and Automatic start and stop conditions
-Programming - API -Programmatically automate any MX measurement -Use C/C++, Visual Basic, or LabVIEW -DLL, VI, OPC support
March 2003 MX100 Regional Training
Software Options
Basic Specifications Features
Dedicated Software
Standard - One-to-one connection with the MX
(Up to 60 channels per unit)
- Setup, monitoring
Logging, redisplay
- Ready for multi-interval- Computation- Relay Output
Enhanced - Connected with two or more number of MX units
- Setup, monitoring
Logging, redisplay
Monitor server
- Ready for multi-interval
- Computation (between the units)
- Relay output - Synchronized data
processing among two or more number of MX units
API
LabView
Functions for setup and data sampling
Saving the man-hours of the users to develop self-made software
March 2003 MX100 Regional Training
MX100 standard software Useful features : Distributed data acquisition
M.N T.F
Multi MX connected under same segment network is detected automatically.
Network configuration menu
Dedicated LAN
March 2003 MX100 Regional Training
MX100 standard software Useful features : Manual DO during monitoring/recording
March 2003 MX100 Regional Training
Combination with DARWIN/DAQSTATION
MXLOGGER
DAQLOGGER
MXLOGGERMonitor Server
MXLOGGERMonitor Server
March 2003 MX100 Regional Training
Logo of DAQWORX
+
March 2003 MX100 Regional Training
Network
DAQWORX Data Highway
I/F
OPC
DAQLOGGERDAQEXPLORER DAQ32+DAQOPC
ADDObserver ADDMultiInTouchVDS
DAQWORX R1
MX-Log
GateDXP GateWT
ADDTRigger
GateOPC
GateEye GateMODBUS
DAQWORX
March 2003 MX100 Regional Training
DAQWORX Roadmap
PC Software
DAQWORX R2Feb
2004
AddDataManagerAddEventAddWebGateFA-M3
Improved installerMore value-add
DAQWORX R3Mid
2004
AddReport+α
Universal Launcher
DAQWORX R1
MX100 loggerAddTriggerGateWTGateEyeGateDX-PGateOPCGateMODBUS
Suite (1 CD)
Jun 2003
Today