multifunctional circuit board tester
TRANSCRIPT
MULTIFUNCTIONAL CIRCUIT BOARD TESTER
1) Dual-Channel Fault Detection by V-I Tester:
Fault detection by direct comparison of the current-voltage characteristics (signatures) of a working and a
faulty circuit board without applying power to the unit under test.
2) Fault Detection by Comparison with Stored Signatures:
Signatures of a functioning board can be saved and used at a later time as a reference for
troubleshooting a faulty board. The point to touch can be indicated by a cross hair mark at an image of
the board.
3) Equivalent Circuit Diagram: ***
Display of an equivalent circuit that corresponds to the characteristic on the touched point.
4) Display Values of Resistor, Capacitor and Diode Threshold: ***
Display the calculated values of resistance, capacitors and diode threshold voltages corresponding to the
conditions at the contacted node.
5) Dual-Channel Digital PC Oscilloscope:
As occasion may require, device can be used as oscilloscope.
6) 0.2... 25 KHz Square Wave Output:
Channel 2 is used as a square wave generator. Channel 1 can be used as an oscilloscope.
7) Analogue Voltage Output:
Channel 2 is used as Analog DC output. Channel 1 can be used as an oscilloscope.
8) Programmable Integrated DC Power Supply: ***
The output voltage is adjustable. 0 to 16 volts with an output current 20 to 1500 mA, for giving energy to
circuit board and creating Power DC Voltage-Current Graph.
9) Non-Touched IR Temperature Probe: ***
To detect more heated components and draw a heat map of the circuit board.
*** These features are unique features.
WWW.GSASINDIA.COM
The FADOS9F1 is designed to diagnose the failures in all types of elecronics circuit boards. It is PC based voltage - current analysis device. It has following 9 functions:
Smar
tpho
ne ? GSAS Micro Systems Private Limited
#106, "Sri Ranga", 1st Floor, 6th Main, Mahalakshmipuram, Bangalore - 560 086+91 80 2349 6051 +91 80 2349 6052 [email protected]
www.gsasindia.com
BANGALORE [email protected] + 91 080 23496051
[email protected] + 91 90008 46051
VIZAG & VIJAYAWADA [email protected] + 91 98450 98535
MUMBAI & PUNE [email protected]+ 91 98450 82950
TAMIL NADU [email protected] + 91 98450 80685
DELHI
[email protected] + 91 98450 82950
FADOS9F1 TECHNICAL SPECIFICATIONS
A- FAULT DETECTION SPECIFICATIONS :
Test Voltages
Test Resistance
: ±1V, ±2V, ±6V, ±12V, ±24V
: Current Level: Low 47KΩ, Med1 3,5KΩ, Med2 700Ω
High 250Ω
Test Frequencies : Very Low Frequency , Low2 Frequency, Low1
Frequency, Test Frequency, High Frequency
Number of Channels : 2 (Channel 1 and Channel 2)
Scan Mode : Manual or Automatic. Automatic selection steps of
voltage, current, frequency.
Other Feature : 1: Equivalent circuit diagram.
2: Resistor, capacitors, diodes etc measurement.
3: Recording data and comparing with recorded data.
4: 3 graphs at different adjustments can be screened
simultaneously.
B- POWER – IR TEMPERATURE FEATURES:
DC Power Source
IR (Infrared) Sensor
: Programmable 0-16V and 20-1500mA power output.
: Shows the difference between 0-120 degrees
according to ambient temperature.
C- PC OSCILLOSCOPE FEATURES :
: 400 K/S
: Probe 1X: ±5 V Probe 10X: ±50 V
Sampling Rate
Input Voltage
Channel / ADC
Sensitivity
Image Rate
Instant Memory
: 2 Channel / 12 Bit
: 2.5 mV
: 0.02 mS/div….100 mS/div
: 64 Kbyte
D- DIGITAL AND ANALOG OUTPUT :
: Channel 2 Output
Output Voltage
Frequency (Digital)
Dimensions
Weight
Warranty
: -12V….+12V (Adjustable)
: From 0.2KHz to 25KHz
: 122mm L x 113mm W x 29mm H
: 1100 gram with all accessories
: 1 year